Fourth Semester B.E. Degree Examination, Dec.2014/Jan.2015Mechanical Measurements and Metrology

Max. Marks: 1.\j,.

<:)~

"~ (05 Marks)ith neat sketches.

(10 Marks)t' used in calibration of

e compared with the meteraping A and B, it was found thatand B. (05 Marks)

Note: Answer FIVE full questions, selectingatleast TWO questions from each part.

a. :E>efin,e.metrology.What are the objectives of metrology?b. Expkf " " mperial standard yard" and "International prototype met '

c. A calibrated eter end bar has an actual length of 1000.0002two bars A antI , each having a basic length of 500 mID.bar LA + LB wasff01.indto be shorter by 0.0003 mID. In coA was 0.0004 mnll n er than B. Find the actual length 0;

1""a. Differentiate: i) unil~eral and bilateral tolerances '- clearance fit and interference fit.

(06 Marks)b. Determine the dimensions of ail: and hole for. fit 30 H7fs. The given data are:

/i = 0.45® + 0.00 ID microns. Funoamental <l0'viationfor f shaft is _5.5D°.41microns, 30 mmfalls in the diameter step 0 f 18 an f'" Tolerance grade for IT7 and IT 8 are 16i and 25irespectively. Also design plug gauge'~o.(e ck the above hole. Take wear allowance as 10%of the gauge tolerance. I (10 Marks)

c. Explain: i) Shaft basis syste ii) Hole basi (04 Marks)

a. With a neat sketch, explain the construction a d working of Johannsoncomparator. ~ J ~

b. Explain with a neac) etch, the working of Solex pgumatic comparator.advar:tages? 0 }'

c. Explain the pFin . Ie of sine bar. ;:R:f }'

a. With a ~at sketch, explain the working principle of an autocollim to . (06 Marks)b. Defin ~'Effective diameter". Explain the 3-wire method of finding t Ii, ctive diameter of

s ". I {breads. "7... (08 Marks)

c. Explain with a sketch, how the chordal thickness is measured by using g tooth verniercaliper. }' ~ 6 Marks)

Mikrokator(08 Marks)

What are its(08 Marks)(04 Marks)

.~/.I

" 5•

a. Defme measurement. With a block diagram, explain the generalized measurement syswith a suitable example. (08 Marks

b. Defme the following terms: i) precision ii) hysteresis iii) sensitivity. (06 Marks)c. Explain the principle of capacitive type electrical transducer. With a sketch explain anyone

type of capacitive transducer. (06 Marks)

6 a. Explain the inherent problems present in mechanical modifying system.b. With a block diagram, explain the general telemetering system.c. Explain with neat sketches: i) stylus type oscillograph ii) x - y - plotter.

(06 Marks)(06 Marks)(08 Marks)

www.bookspar.com | VTU NOTES | QUESTION PAPERS | NEWS | VTU RESULTS | FORUM | VTU BOOKSPAR APP

www.bookspar.com | VTU NOTES | QUESTION PAPERS | NEWS | VTU RESULTS | FORUM | VTU BOOKSPAR APP

a. Sketch and explain the analytical balance (equal arm balance).b. Explain how the torque is measured using prony brake dynamometer.

disad vantages?c. Describe the working principle ofpirani gauge with a sketch.

(08 Marks)What are its

(06 Marks)(06 a

8 a. State the laws of thermocouples.~ Explain the construction and working of optical pyrometer.

c. ""IDefinegauge factor. Explain the wheat stone bridge arrangement for straiJe ~,/0- V\

~, ~~

6>-0)('. ~X~~..I- *****~/. ,"-

~ ,,"°C~ @~~ rlO~

•••~ ~"J?S ;v~()O

~<c; 'QCOV ~

0-0~ ~ @l09 /)'

~~ '70<:' ~B

&.($ OJ:~ ~/

t?~~Q

9'

www.bookspar.com | VTU NOTES | QUESTION PAPERS | NEWS | VTU RESULTS | FORUM | VTU BOOKSPAR APP

www.bookspar.com | VTU NOTES | QUESTION PAPERS | NEWS | VTU RESULTS | FORUM | VTU BOOKSPAR APP