mechanic agriculture machinery 1st year module 1 - safety … · 2020-01-10 · 66 : what is the...

Mechanic Agriculture Machinery– 1st year Module 1 - Safety workshop practices Reviewed and updated on: 01st November 2019 Version 1.1

NIMI Question Bank of 57

1 : Which type of protective equipment used to protect head? A : Boot B : Mask C : Apron D : Helmet

2 : Which part of the human body need to protect in high noise level at work place? A : Ear B : Eye C : Nose D : Head

3 : Which type personal protective equipment is recommended for use, to handle loads with rough surfaces and jagged edges? A : Paper gloves B : Rubber gloves C : Leather gloves D : Polythene gloves

4 : What is the name of the protection sign?

A : Eye protection B : Head protection C : Hearing protection D : Respiratory protection

5 : What is the name of the safety sign?

A : Wear head protection B : Protect head from rain C : Sun cap must be worn D : Only construction workers allowed

6 : Which types of safety involves wearing of safety shoes and goggle in a workshop? A : General safety B : Personal safety C : Machine safety D : General and machine safety

7 : Which area is restricted for smoking? A : Water filling area B : Fuel refilling area C : Gram market area D : Corporation limit area

8 : Which is the cause for fire while refueling the hot engine? A : Vapour B : Paper C : Cloth D : Leather

9 : Which type of fuel contains more carbon monoxide? A : Solid fuel B : Burnt fuel C : Liquid fuel D : Unburnt fuel

10 : Which automobile component produces dust? A : Axle B : Piston C : Gear box D : Brake shoe

11 : Which type of material toxic may cause for lung cancer? A : Fiber B : Wood C : Graphite D : Asbestos

12 : Which comes under first aid? A : Treating a victim for a shock B : Completing a primary source C : Assessing a victim’s vital signs D : Immediate care and support given to injured person



13 : Which part of body, if bleeding profusely is considered serious and need professional attention? A : Leg B : Knee C : Wrist D : Buttock

14 : What is your immediate action on completion of first aid? A : Call taxi B : Call your friend C : Call fire service D : Call emergency service

15 : What is ABC in first aid? A : Army, Branch, Calculate B : Aviation, Breathing, Cumin C : Away, Breathing, Calculation D : Airway, Breathing, Circulation

16 : Which is the three elements must be present for burning of any fire? A : Fuel + Heat + Oxygen B : Oxygen + Fuel + Paper C : Heat + Water + Oxygen D : Smoke + Fuel + Oxygen

17 : What is called the isolating the fire from the supply of oxygen by blanketing with foam and sand? A : Cooling B : Starting C : Misfiring D : Smothering

18 : What is the cause for electric fire? A : Rated fuses B : Under loaded circuit C : Over loaded circuits D : Tight wire connection

19 : Which is highly flammable liquid? A : LPG B : Water C : Diesel D : Crude oil

20 : What is the type of fire with wood, cloth, and paper? A : Class - A B : Class - B

C : Class - C D : Class - D

21 : Which gas is to be eliminated to prevent fire? A : Carbon-di-oxide B : Argon C : Oxygen D : Nitrogen

22 : Which is chemical hazard? A : Noise B : Explosive C : Vibration D : Radiation

23 : Which fire extinguisher used for flammable liquid fires? A : Halon extinguisher B : Dry powder extinguisher C : CTC extinguisher D : Water extinguisher

24 : Which is unsuitable fire extinguisher for class B fire? A : Water fire extinguisher B : Foam fire extinguisher C : Dry powder fire extinguisher D : Carbon dioxide extinguisher

25 : Which class of fire involving liquefied gases? A : Class ‘A’ B : Class ‘B’ C : Class ‘C’ D : Class ‘D’

26 : Which is the major energy conservation opportunities? A : Stopping of leakage B : Replacement machineries C : Replacement of house hold appliance D : Laps in house keeping

27 : Which type of energy conservation comes under the renovation of old buildings? A : Minor energy conservation opportunities B : Major energy conservation opportunities C : Medium energy conservation opportunities D : Very minor energy conservation opportunities



28 : Which is medium energy conservation opportunities? A : House keeping B : Stopping of water leakage C : Renovation of the old building D : Replacement of existing house hold appliances

29 : Which material is best for use to cover a “oil spill” in the workshop? A : Dry sand B : Saw dust C : Waste cloth D : Card board cover

30 : Which safety involves wearing safety shoes or boot and goggle in a workshop? A : Personal safety B : General safety C : Machine safety D : General safety machine safety

31 : Which type of energy conservation opportunity involves stopping of water leakage points? A : Minor energy conservation opportunities B : Major energy conservation opportunities C : Medium energy conservation opportunities D : Extra major energy conservation opportunities

32 : Which safety precaution to be adopted in handling diesel machine? A : Use correct viscosity oil B : Remove safeguard of rotating part C : Use oil/greasy hand to repair work D : Use diesel engine with loose mounting

33 : What is the best way of avoiding accident? A : Doing work in sequence B : Doing work in own way C : Observing safety rules related to job machine and work place D : Using safety equipments

34 : Which one of the following cranes is used for loads and transport to another location? A : Overhead crane B : Travelling crane C : Piller gib crane D : Gantry crane

Mechanic Agriculture Machinery– 1st year Module 2 - Engineering Measurement Reviewed and updated on: 01st November 2019 Version 1.1


35 : Which spanner used for zero setting in outside micrometer? A : Cʹ spanner B : Ring spanner C : Double end spanner D : Adjustable spanner

36 : What is the name of marking instrument?

A : Bevel gauge B : Bevel protractor C : Universal bevel gauge D : Universal surface gauge

37 : Which one is the indirect measuring instrument? A : Steel rule B : Inside caliper C : Inside micrometer D : Outside micrometer

38 : Which is used for marking and setting of work? A : Surface plate B : Marking table C : ‘V’ Block D : Bench vice

39 : What is the name of tool?

A : Flat chisel B : Cap chisel C : Diamond chisel D : Half round chisel

40 : What is the name of vice?

A : Pin vice B : Hand vice C : Tool maker’s vice D : Quick release vice



41 : What is the name of equipment?

A : Surface plate B : Angle plate C : ‘V’ Block D : Parallel Block

42 : Which instrument is used to check the right angle? A : Steel rule B : Try square C : Firm joint caliper D : Spring joint caliper


A : Allen key B : Feather key C : Gib head key D : Woodruff key

44 : What is the name of plier?

A : Flat nose plier B : Round nose plier C : Slip joint plier D : Internal circle plier

45 : What is the name of part marked as ‘x’?

A : Face B : Cheek C : Wedge D : Pein



46 : What is the name of hammer?

A : Club hammer B : Ball peen hammer C : Cross peen hammer D : Straight peen hammer

47 : What is the name of caliper?

A : Firm joint caliper B : Spring joint caliper C : Out side caliper D : Inside caliper

48 : What is the name of plier?

A : Flat nose plier B : Round nose plier

C : Slip joint multigrip plier D : Internal circle plier

49 : What is the use of ball pein hammer head? A : Strike soft metal B : Strike the metal C : Stamp the specifications D : Spread the metal In all direction

50 : What is the purpose of the cross pein in the hammer? A : Fix the handle B : Strike the metal C : Strike the metal in all direction D : Spread the metal in one direction

51 : Which tool used to tighten the nuts and bolts at recommended tightness? A : Stud wrench B : Pipe wrench C : Torque wrench D : Adjustable wrench


A : Socket ratcheting adapter B : Socket adapter C : Socket ratchet handle D : Socket sliding handle

53 : Which wrench is used measure the twisting force? A : Torque wrench B : Still son pipe wrench C : Footprint pipe wrench D : Hexagonal socket wrench



54 : What is the name of screw head?

A : Pan head B : Cheese head C : Raised cheese head D : Round head

55 : What is the name of the part marked as ‘X’?

A : Cap B : Lock C : Stock D : Graduated sleeve

56 : What is the least count of the metric outside micrometer? A : 0.01 mm B : 0.10 mm C : 0.0001 mm D : 0.00001 mm

57 : Which part ensures uniform pressure on the measuring faces in the outside micrometer? A : Barrel B : Spindle C : Thimble D : Ratchet Slop

58 : Which is the fixed measuring face of micrometer? A : Anvil B : Barrel C : Spindle D : Thimble

59 : Which material used to make micrometer anvil? A : Brass B : Bronze C : Carbon D : Carbide


A : Anvil B : Frame C : Spindle D : Thimble




A : Anvil B : Frame C : Spindle D : Thimble

62 : How many equal thimble divisions are made in outside micrometer metric? A : 30 Divisions B : 40 Divisions C : 50 Divisions D : 60 Divisions

63 : What is the smallest possible measurement that can be taken with the depth micrometer? A : 0.01 mm B : 0.02 mm C : 0.001 mm D : 0.002 mm

64 : What is the name of part marked as “X”?

A : Beam B : Fixed jaw C : Vernier scale D : Depth measuring blade

65 : What is the name of the part marked as ‘X’ in vernier caliper?

A : Beam B : Lock screw C : Sliding unit D : Movable jaw

66 : What is the least count of vernier caliper in metric system? A : 0.1 mm B : 0.0001 mm C : 0.02 mm D : 0.001 mm

67 : Which measuring instrument used to measuring inside, outside and depth of work piece? A : Steel rule B : Micrometer C : Dial caliper D : Vernier caliper

68 : Which part of vernier caliper used to measure internal and external measurement? A : Beam B : Sliding unit C : Fixed jaw D : Movable jaw



69 : What is the name of the measuring instrument?

A : Depth gauge B : Bore dial gauge C : Telescopic gauge D : Vernier gauge


A : Spindle B : Plunger C : Centring shoes D : Fixed anvil insert


A : Spindle B : Plunger C : Fixed Anvil Insert D : Centering shoes


A : Stem B : Plunger C : Fixed Anvil Insert D : Centering shoes

73 : Which instrument used to read the telescopic gauge measurement? A : Depth micrometer B : Inside micrometer C : Outside micrometer D : Three point internal micrometer




A : Anvil B : Stem C : Plunger D : Pointer

Mechanic Agriculture Machinery– 1st year Module 3 - Basic workshop practice Reviewed and updated on: 01st November 2019 Version 1.1


75 : Name the part marked as ‘x’ in a rivet?

A : Tail B : Body C : Head D : Diameter

76 : Which rivet is used in heavy structural work? A : Pan head rivet B : Snap head rivet C : Counter sunk rivet D : Conical head rivet

77 : Which rivets are used in light assembly work? A : Pan head rivet B : Snap head rivet C : Counter sunk rivet D : Conical head rivet

78 : What is the fault in riveting?

A : Burrs between plates B : Rivet head not centered C : Too much allowance given D : Holes on the plate are not in line

79 : What is the name of riveting defect?

A : Too little allowance on shank B : Too much allowance on shank C : Rivet head not centered with shank D : Head of rivet not perpendicular to shank

80 : Name the part of lever shear marked as ‘x’.

A : Base plate B : Lever arm C : Lower blade D : Upper blade

81 : Which sheet metal is highly resistant to corrosion and abrasion? A : Copper B : Black iron C : Aluminium D : Galvanised iron

82 : What is the name of tool used to cut thicker sheets? A : Bend snips B : Lever shears C : Straight snips D : Circle cutting machine



83 : What is the seam used in sheet metal joint for roofing and panelling? A : Lap seam B : Double seam C : Grooved seam D : Double grooved seam

84 : Which metal is very soft and heavy in sheet metal work? A : Lead B : Black iron C : Aluminium D : Copper sheet

85 : Name the type of seam.

A : Lap seam B : Double seam C : Grooved seam D : Double grooved seam

86 : Which sheet metal withstand contact with water and exposure to weather? A : Black iron B : Copper sheet C : Stainless sheet D : Galvanised iron

87 : What is the purpose of groover? A : Releasing of seam B : Compress the seam C : Closing and locking of seam D : Stress relieving during seam operation

88 : Name the part marked as ‘x’ of the file.

A : Heel B : Edge C : Ferrule D : Shoulder

89 : Which file is used to make the job close to the finishing size? A : Single cut file B : Curved cut file C : Second cut file D : Double cut file

90 : Which file has the parallel edges throughout the length? A : Hand file B : Bastard file C : Rasp cut file D : Single cut file

91 : Which grinding machine is used for heavy duty work? A : Bench grinder B : Portable grinder C : Pedestal grinder D : Surface grinder



92 : What is the name of file?

A : Hand file B : Rasp cut file C : Single cut file D : Curved cut file

93 : Name the defect that causes the metal chips to clog between the teeth of file. A : File bite B : Pinning of file C : Warping of file D : Glazing of file

94 : What is the part marked as ‘x’ in pedestal grinder?

A : Tool rest B : Eye shield C : Wheel guard D : Grinding wheel

95 : What is the name of the tool?

A : Stone dresser B : Diamond dresser C : Star wheels dresser D : Abrasive stick dresser

96 : Which term indicates the amount of bond present between the individual abrasive grains? A : Grain B : Grade C : Abrasive D : Structure

97 : Which type of bonded wheel is used in foundries for dressing castings? A : Silicate bond B : Shellac bond C : Rubber bond D : Resinoid bond



98 : What is the tool used in grinding operation?

A : Honing tool B : Abrasive stick C : Diamond dressers D : Star wheel dressers

99 : What is the name of the fit?

A : Transition fit B : Clearance fit C : Shrinkage fit D : Interference fit

100 : What is the difference between maximum limit of size and the minimum limit of size? A : Tolerance B : Basic size C : Limits of size D : Upper deviation

101 : What is the number of fundamental deviation in the BIS system available? A : 25 B : 20 C : 15 D : 26

102 : How many fundamental tolerance grades are available? A : 18 grade

B : 25 grade C : 15 grade D : 12 grade

103 : What is the name of the angle marked as ‘X’ in drill bit?

A : Helix angle B : Lead angle C : Point angle D : Chisel edge angle

104 : What is the purpose of clearance angle in twist drill? A : Prevent rough holes B : Prevent over size holes C : Prevent unequal angle of cutting edges D : Prevent friction of drill behind the cutting edges

105 : Which decides the point angle of drill? A : Drill material B : Job material C : Cutting speed D : Size of the drill



106 : How the size of drill bit is measured? A : Between flutes B : Between the lands C : Between web D : Neck diameter

107 : Which method is suitable to remove the broken stud very near to the surface? A : Ezy out method B : Making drill hole C : Prick punch method D : Using square taper punch

108 : Which reamer will have a long taper lead? A : Hand reamer B : Socket reamer C : Machine reamer D : Helical fluted reamer

109 : Name the type of the reamer.

A : Hand reamer B : Helical reamer C : Machine reamer D : Taper pin reamer

110 : What is the name of the die?

A : Split die B : Half die C : Solid die D : Adjustable screw plate die

111 : What is the method of removing broken stud?

A : Ezy-out B : Prick punch C : Making drill hole D : Using square taper punch

112 : What is the name of the process of finishing the drilled hole? A : Reaming B : Spot facing C : Counter boring D : Counter sinking



113 : What is the use of reamer? A : Drill a hole B : Enlarging a hole C : Threading a hole D : Finishing to correct size of the drilled hole

114 : What is the function of pilot in the hand reamer? A : Keep size of hole accurate B : Removes the burr from the hole C : Provide smooth functioning of reamer D : Keep reamer concentric with hole to be reamed

115 : What is the method of removing the broken stud?

A : Ezy- out method B : Prick punch method C : Making drill hole method D : Using square taper punch method

116 : Why hand reamers have uneven spacing of teeth? A : Reduce chattering B : Remove more metals C : Increase the efficiency D : Increase the life of the tool

117 : Why centre screw is provided in the die stock? A : To tighten the die B : To adjust the depth of cut C : To adjust the dia of internal thread D : To adjust the dia of external thread

118 : What is the tap drill size for M20 x 1.5? A : 18.5 B : 20 C : 19 D : 17

119 : What is the material of solder? A : Welding rod B : Synthetic element C : Pure metal or alloy D : Non metallic element

120 : How to specify the soldering bit? A : By the weight of copper head B : By over all size of the head C : By geometry of the head D : By the length of the head

121 : Which type of flux commonly used for ferrous and non ferrous metal? A : Zinc chloride B : Phosphoric acid C : Ammonium chloride D : Hydro chloric acid

122 : Which process is a similar to brazing but it gives a much stronger joint than the soldering? A : Brazing B : Welding C : Seaming D : Hemming

123 : What is the purpose of soldering iron? A : To melt joining metal B : To melt solder and heat metal C : To melt solder D : To heat joining metal

124 : What is the tin and lead composition ratio of extra fine solder? A : 40 : 60 B : 66 : 34 C : 63 : 37 D : 70 : 30



125 : What is the tin and lead composition ratio for common solder? A : 50 : 50 B : 60 : 40 C : 66 : 34 D : 70 : 30

126 : What is solder? A : Cleaning agent B : Lubricant C : Melting agent D : Filler material

127 : What is the function of flux on soldering surface? A : Remove oxides B : Smoke control C : Remove burrs D : Heat the solder

128 : Which type of flux is made from animal fat? A : Zinc chloride B : Ammonium chloride C : Resin D : Tallow

129 : Which method used to remove flux after welding on aluminium alloy metal? A : By acid chromate bath B : By chipping hammer or wire brush C : Wash by boiling water and brushing D : By nitric and hydro fluoric acid

130 : Which riveting tool is used to form the final shape of rivet? A : Drift B : Dolly C : Rivet set D : Rivet snap

131 : Which flux is used for soldering tin sheets? A : Resin B : Paste C : Zinc chloride D : Ammonium chloride

132 : What is the name of drilling machine?

A : Ratchet hand drill B : Pneumatic hand drill C : Electric hand drill light duty D : Electric hand drill heavy duty

133 : What is the type of the reamer?

A : Expansion reamer B : Hand reamer C : Socket reamer D : Machine reamer

Mechanic Agriculture Machinery– 1st year Module 4 - Basic Electrical and Electronics Reviewed and updated on: 01st November 2019 Version 1.1


134 : Which is the Ohm’s Mathematical Expression? A : I=V/R B : I=R/V C : V=I/R D : R=I/V

135 : What is the permissible voltage drop in the electrical circuit? A : 0.1 V B : 0.2 V C : 0.3 V D : 0.4 V

136 : How many cells are available in the 12V Battery? A : 2 cells B : 6 cells C : 9 cells D : 12 cells

137 : Which law state that “The current is directly proportional to the voltage and inversely proportional to the resistance”? A : Ohm’s Law B : Hook’s Law C : Boyle’s Law D : Newton’s Law

138 : Which instrument is used to measure the electrical resistance? A : Ammeter B : Voltmeter C : Ohmmeter D : Wattmeter

139 : Which instrument is prohibited to connect with live wire? A : Ammeter B : Voltmeter C : Ohmmeter D : Wattmeter

140 : What is the name of the electrical measuring instrument?

A : Ammeter B : Voltmeter C : Wattmeter D : Multimeter

141 : Which is a temperature sensitive resistor? A : Diode B : Thyristor C : Thermistor D : Transistor



142 : What is the name of the symbol?

A : Diode B : Transistor C : Triode D : Thermistor

143 : How to express battery capacity? A : Ampere - hour rating B : Voltage - hour rating C : Ampere rating D : Voltage rating

144 : Which instrument is used to check the continuity of the field coils of DC motor? A : Ammeter B : Voltmeter C : Ohmmeter D : Wattmeter

145 : Which type of the circuit has an infinite resistance? A : Open circuit B : Short circuit C : Series closed circuit D : Parallel closed circuit

146 : What is the net resistance ‘R’ if ‘R1’ and ‘R2’ resistance are connected in series? A : R = R1 + R2 B : R = R1 – R2 C : R = R1 x R2 D : R = R1/R2

147 : What type of resistor is used in the vehicle flasher unit? A : Ballast resistor B : Film resistor C : Printed resistor D : Integrated resistor

148 : Which electronic component is used as a solid state switch? A : Inductor B : Resistor C : Capacitor D : Transistor

149 : Which material is required to make integrated circuit chips? A : Zinc B : Steel C : Silicon D : Copper

150 : What is the name of the circuit?

A : Open circuit B : Short circuit C : Closed circuit D : Parallel circuit

151 : Which device have the ability to store electrical charge? A : Capacitor B : Resistor C : Insulator D : Conductor



152 : What is the effect of the soft iron bar in a closed circuit?

A : Shock effect B : Heating effect C : Magnetic effect D : Chemical effect

153 : What is the name of electrical symbol?

A : Capacitor B : Battery C : Earth D : Resistance

154 : What is the ampere hour rating if battery deliver 5 ampere and period of 20 hours? A : 80 Ampere hour B : 90 Ampere hour C : 100 Ampere hour D : 110 Ampere hour

155 : Which type of the circuit leads to hazard effect? A : Open circuit B : Series circuit C : Short circuit D : Parallel circuit

156 : What is the reason for fuse blown out in an electrical circuit? A : Open circuit B : Short circuit C : Series circuit D : Parallel circuit

157 : What is the material of positive plate in the lead acid battery? A : Tin B : Lead peroxide C : Antimony D : Spongy lead

158 : What is the material of negative plate in the lead acid battery? A : Spongy lead B : Tin C : Antimony D : Lead peroxide

159 : What is the colour of positive plates in the charged lead - acid - battery? A : Grey B : Brown C : White D : Black

160 : How the lead acid battery is classified? A : Dry cell B : Secondary cell C : Alkaline cell D : Primary cell

161 : How is the battery capacity expressed? A : Ampere - hour rating B : Voltage - hour rating C : Ampere rating D : Voltage rating



162 : What is the battery charge rate indicates by the floating level of hydrometer?

A : Discharge B : 1/4 charge C : 1/2 charge D : Full charge

163 : What is the energy conversion of battery during discharge? A : Electrical energy into heat energy B : Chemical energy into electrical energy C : Electrical energy into chemical energy D : Electrical energy into mechanical energy

164 : What is the energy conversion of battery during charging? A : Electrical energy into chemical energy B : Electrical energy into heat energy C : Chemical energy into electrical energy D : Electrical energy into mechanical energy

165 : What is the name of the electronic symbol?

A : Diode B : Switch C : Battery D : Transistor

166 : Name the logic gate.

A : AND gate B : OR gate C : NOT gate D : NAND gate

167 : Name the logic gate.

A : AND gate B : OR gate C : NOT gate D : NAND gate



168 : What is the name of the symbol?

A : OR gate B : AND gate C : NOT gate D : NAND gate

169 : Which logic gate is called as “Inverter”? A : OR gate B : AND gate C : NOT gate D : NOR gate

Mechanic Agriculture Machinery– 1st year Module 5 - Manufacturing process hydraulic and Pneumatics

Reviewed and updated on: 01st November 2019 Version 1.1


170 : Which arc welding machine can be used anywhere in the field work even away from electric lines? A : Rectifier set B : Motor generator set C : Engine generator set D : AC welding transformer

171 : Which arc welding machine provides better heat distribution in the electrode and job? A : Rectifier set B : Motor generator set C : Welding transformer D : Engine generator set

172 : Which factor determine the current setting during welding? A : Types of joint B : Position of weld C : Length of electrode D : Diameter of electrode

173 : Name the joint in the arc welding.

A : Flush corner joint B : Single fillet lap joint C : Half open corner joint D : Full open corner joint

174 : What is the name of the the metal edge in an angle during welding and cutting operations? A : Kerf B : Drag C : Bevel D : Gouging

175 : Why the cylinder keys are not removed from the cylinder while welding? A : To prevent gas leak B : To adjust the gas supply C : To open and close frequently D : To close quickly in case of fire

176 : How to extinguish the flame after use in gas welding? A : Shut off oxygen and dip blow pipe in water B : Shut off oxygen and acetylene valve at a time C : Shut off oxygen valve first next acetylene valve D : Shut off acetylene valve first next oxygen valve

177 : Identify the part marked as ‘x’.

A : Safety plug B : Steel bottle C : Valve spindle D : Dissolved acetylene





A : Handle B : Mixing chamber C : Oxygen control value D : Acetylene control value

179 : What is the disadvantage of AC welding transformer? A : More initial cost B : Not free from arc blow C : More maintenance cost D : Not suitable for welding non ferrous metal

180 : What is the purpose of cellulosic electrode in arc welding process? A : Very easy to remove the deposited slag B : Used for high strength steel C : It is used for low carbon steel D : It is suitable for all position

181 : Which is the case hardening process? A : Tempering B : Annealing C : Normalising D : Nitriding

182 : What is the quenching media of normalising? A : Water spray B : Open air C : Oil bath D : Water bath

183 : What is the Quenching media of alloy steel in hardening process? A : Water spray B : Open air

C : Oil bath D : Water bath

184 : What is the name of process?

A : Annealing B : Carburising C : Normalising D : Case hardening

185 : Which type of hardening used eddy current in the metal bar? A : Flame hardening B : Nitriding hardening C : Induction hardening D : Annealing hardening

186 : What is the name of heat treatment process?

A : Nitriding B : Annealing C : Carburising D : Induction hardening




187 : Which one is the heat treatment process? A : Riveting B : Soldering C : Normalising D : Welding

188 : Which one is the heat treatment process? A : Casting B : Machining C : Welding D : Annealing

189 : What is the purpose of hardening? A : Increase ductility B : Increase malleability C : Increase hardness D : Increase brittleness

190 : What is the important role of non destructive testing? A : Quality control B : Planning control C : Production control D : Material control

191 : What is the name of valve?

A : Single control valve B : Double control valve C : 3/2-Directional control valve D : 2/2- Directional control valve


A : By pass valve

B : Pressure relief valve C : 2/2 Way directional control valve D : 3/2 Way directional control valve

193 : What is the name of mechanical symbol?

A : Push button B : Plunger C : Foot pedal D : Hand lever

194 : What is the name of mechanical symbol?

A : General B : Plunger C : Push button D : Foot pedal




195 : What is the name of part marked as ‘X’ in hydraulic clutch?

A : Reservoir B : Pedal C : Hose D : Clutch

196 : What is the name of part marked as ‘X’ in the hydraulic power steering?

A : Suction pipe B : Pressure Pipe C : Return Pipe D : Over flow pipe

197 : Which type of pump used in the hydraulic jack? A : Gear pump B : Plunger pump

C : Vane pump D : Internal gear pump


A : Check valve B : Choke valve C : Throttle valve D : Pressure relief valve

199 : Which law is applied in hydraulic brake system? A : Boyle’s law B : Charles law C : Pascal’s law D : Newton’s law




200 : What is the name of NDT method?

A : Ultrasonic test B : Eddy current test C : Magnetic particle test D : Radio graphic test

201 : What is the name of NDT method?

A : Ultra sonic testing B : Radiographic testing C : Liquid penetrate testing D : Electro magnetic yoke testing

202 : Which type of components can be tested by magnetic particle test? A : Non-ferrous components

B : Ferrous components C : Aluminium components D : Plastic components

203 : What is the objective of Non-Destructive testing? A : Find cracks B : Find atomic structure C : Find the weld quality D : Find the flux density

204 : What is the use of liquid penetrant test? A : Clean the surface B : Remove the dust C : Indicate cracks D : Remove excess penetrate

205 : What is the purpose of non destructive testing in auto components? A : Find surface defects B : Find hardness C : Find the brittleness D : Find the chemical composition

206 : Which component increase the pressure in the hydraulic system? A : Control valve B : Oil pump C : Cylinder D : Reservoir

207 : Which type of NDT method used ferrous particles are applied to the area between the poles? A : Ultra sonic testing B : Radiographic testing C : Liquid penetrate testing D : Electro magnetic yoke testing

208 : Which part is used in the pneumatic brake? A : Brake chamber B : Master cylinder C : Wheel cylinder D : Slave cylinder




209 : Which device converts mechanical into pneumatic energy? A : Actuator B : Generator C : Alternation D : Compressor

210 : Which part in the internal gear pump act as seal? A : Gears B : Gasket C : Sealing ring D : Crescent-shaped spacer

211 : What is the name of part marked as ‘X’?

A : Air tank B : Air pressure gauge C : Brake valve D : Compressor


A : Actuator B : Control valve C : FRL D : Compressor

213 : Which equipment is used for only levelling the soil ground? A : Tractor B : Dozer C : JCB D : Jeep

214 : Which type of vehicle provides separate steering for left and right wheel tracks? A : Tractor B : Jeep C : Tipper D : Bulldozer

215 : Which electrical device rotate the flywheel of tractor engine? A : Alternator B : Starter motor C : Battery D : Wiper motor




216 : Which type of cranking system is used to crank the heavy duty multicylinder diesel engine? A : Compressed air cranking B : Gasoline engine cranking C : Handle cranking D : Rope cranking


A : Jack stand B : Hydraulic Jack C : Mechanical Jack D : Hydraulic car hoist


A : Car hoist B : Engine hoist C : Hydraulic jack D : Hydraulic press


A : Car hoist B : Grease gun C : Hydraulic jack D : Hydraulic press

220 : Which type of vehicle capable of sensing its environment and navigating without human input? A : Diesel car B : Petrol car C : Electric car D : Driver less car

221 : Which type service equipment used in car service station to lift the car? A : Arbor press B : Hydraulic jack C : Hydraulic hoist D : Hydraulic press




222 : Which is used for quick inspection under the chassis of a car? A : Stands B : Screw jack C : Trolley jack D : Two post hoist

Mechanic Agriculture Machinery– 1st year Module 6 - Servicing of Tractor and Engine components



223 : Which type of vehicle is used for hitching the agricultural implements? A : Bulldozer B : Tractor C : Tipper D : Mini van

224 : Which is a larger tracked vehicle? A : Jeep B : Tractor C : Dozer D : Van

225 : Which type of vehicle rotate in 360°? A : Jeep B : Bull dozer C : Tractor D : Mini van

226 : Which type of cranking system is used in small power generator? A : Hand cranking B : Gasoline engine starting C : Compressed air cranking D : Electric motor cranking

227 : What is the type of engine cranking system?

A : Rope cranking B : Handle cranking C : Electric motor cranking D : Compressed air cranking

228 : What is the name of part marked as ‘X’ in electric motor cranking system?

A : Piston B : Battery C : Fly wheel D : Starter motor

229 : Which cranking system is provided in the tractor engine? A : Rope cranking B : Handle cranking C : Compressed air cranking D : Electric motor cranking




230 : What is the type of engine?

A : In-line engine B : V engine C : Opposed engine D : Radial engine


A : In line engine B : ‘V’ engine C : Opposed engine D : Radial engine


A : Inline engine B : ‘V’ engine C : Opposed engine D : Radial engine


A : Inline engine B : ‘V’ engine C : Opposed engine D : Radial engine

234 : Which type of valve used in two stroke engine? A : Reed valve B : Sleeve valve C : Rotary valve D : Poppet valve

235 : Which plug is used to pre heat the combustion chamber of diesel engine? A : Glow plug B : Safety plug C : Spark plug D : Drain plug




236 : Which part of the engine ignite the fuel in four stroke engine? A : Crank case B : Intake manifold C : Combustion chamber D : Exhaust main fold

237 : What is the name of cylinder head?

A : ‘ L ‘ head B : ‘ I ‘ head C : ‘ F ‘ head D : ‘ T ‘ head


A : ‘ L ‘ head B : ‘ I ‘ head

C : ‘ F ‘ head D : ‘ T ‘ head


A : ‘ L ‘ head B : ‘ I ‘ head C : ‘ F ‘ head D : ‘ T ‘ head

240 : What is the name of part marked as ‘X’ in cylinder head?

A : Wedge combustion chamber B : Pre-combustion chamber C : Hemispherical combustion chamber D : Swirl combustion chamber





A : Reed valve B : Rotary valve C : Sleeve valve D : Poppet Valve


A : Poppet Valve B : Rotary valve C : Reed valve D : Sleeve valve

243 : What is the name of part marked as ‘X’ in overhead valve mechanism?

A : Tappet B : Cam lob C : Push rod D : Rocker arm

244 : What is the name of part marked as ‘X’ in side valve mechanism?

A : Valve B : Cam lobe C : Gudgeon pin D : Connecting rod




245 : Which part of the overhead valve mechanism moves the valve against the spring tension? A : Tappet B : Cam lobe C : Rocker arm D : Push rod

246 : Which part of the engine fastened with oil pan? A : Cylinder head B : Cylinder block C : Cylinder liner D : Cylinder block oil main gallery


A : Oil pan B : Engine block C : Cylinder head D : Valve door cover

248 : Which type of material used to make wet type liners? A : Aspetas B : Copper

C : Nitrided cast iron D : Aluminium

249 : Which part of the engine converts the reciprocating motion of the piston into rotary motion of crank shaft? A : Push rod B : Cam shaft C : Rocker arm D : Connecting rod

250 : Which portion of the piston absorbs high pressure and temperature during combustion? A : Piston crown B : Piston boss C : Piston land D : Piston skirt

251 : Which type of piston head is easy to decarbonise? A : Flat head B : Domed head C : Concave head D : Irregular head

252 : Which type of piston head has a conical shaped projection inside the cavity? A : Domed head B : Concave head C : Flat head D : Irregular head

253 : Which side of the piston get maximum thrust during engine run in clockwise? A : Left side B : Right side C : Front side D : Rear side

254 : Which portion of the piston helps to maintain a constant clearance with cylinder bore? A : Slot B : Crown C : Land D : Piston pin




255 : Which part of an engine drive the cam shaft? A : Counter shaft B : Clutch shaft C : Crank shaft D : Converter shaft

256 : Which device is fitted in front end of the crank shaft to balance the torsional torque? A : Connecting rod B : Vibration damper C : Cam shaft D : Pulley

257 : Which part of the engine stores energy during the power stroke? A : Cam shaft B : Crank shaft C : Fly wheel D : Timing gear

258 : What is the function of fly wheel ring gear in tractor? A : Store the energy B : Crank the engine C : Balancing the fly wheel D : Drive the pinion gear

259 : What is the name of part marked as ‘X’ in gear?

A : Pump mark B : Chain mark C : Timing mark D : Gear band mark

Mechanic Agriculture Machinery– 1st year Module 7 - Cooling and Lubrication System Reviewed and updated on: 01st November 2019 Version 1.1


260 : In which type of cooling system used fins on the cylinder head? A : Oil cooling B : Water cooling C : Liquid cooling D : Air cooling

261 : In which types of cooling system’s rate of cooling is very low? A : Thermo siphon system B : Air cooling system C : Forced feed system D : Pump circulation system

262 : How the water circulation is obtained in thermosyphon system? A : By forced feed of water B : By density of water of hot and cold water C : By gravity of water D : By water jackets

263 : How the water pump get drive in pump circulation cooling system? A : By belt B : By gear C : By chain D : By coupling

264 : What is the name of the part marked as ‘x’?

A : Radiator upper tank

B : Radiator lower tank C : Radiator drain plug D : Radiator cap

265 : How to check the damaged radiator core tubes? A : Check visually B : Check with special tools C : Check with computer D : Check with bore dial gauge

266 : Which lubrication system used separate oil tank? A : Wet sump lubrication B : Splash lubrication C : Petrol-oil lubrication D : Dry sump lubrication

267 : Which type of lubrication system used in two stroke engine? A : Dry sump lubrication B : Wet sump lubrication C : Petrol-oil lubrication D : Splash lubrication

268 : Which is related to lubrication system? A : Provide a cushioning effect to oil filter B : Increase the wear and tear of the moving parts C : Increase the blow by gases by providing an oil D : Minimise the wear and tear of the moving parts

269 : Which part of the crank shaft flow oil to crank pin? A : Crank web B : Crank shaft thrust bearing C : Crank shaft main journal D : Crank pulley

270 : Which is the property of a lubricant? A : Boiling temperature should be low B : Should develop foam C : Oil viscosity should not be same in hot and cold condition D : Oil viscosity should be suit the operating conditions

Mechanic Agriculture Machinery– 1st year Module 7 - Cooling and Lubrication System Reviewed and updated on: 01st November 2019 Version 1.1


271 : What is the main purpose of the lubricant? A : Minimise the friction B : Increase the friction C : Increase the weariness D : Increase the noise

272 : Which device sucks oil from oil sump? A : Strainer B : Suction pipe C : Pump D : Filter

273 : What is the name of the part marked as ‘x’?

A : Water pump pulley B : Water pump impeller C : Water pump housing D : Water pump shaft


A : Water pump B : Hydraulic pump C : Fuel pump D : Oil pump

Mechanic Agriculture Machinery– 1st year Module 8 - Intake and Exhaust fuel system Reviewed and updated on: 01st November 2019 Version 1.1


275 : What type of filter element is used in dry type air cleaner? A : Paper element B : Cloth element C : Wire mesh element D : Strainer element

276 : Where the turbo charger compressor housing outlet connected? A : Connected to air cleaner B : Connected to inlet-manifold C : Connected to exhaust - manifold D : Connected to oil filter

277 : During engine back fire, which act as a flame arrester? A : Oil filter B : Fuel filter C : Air filter D : Muffler

278 : Which type of muffler produces anti noise without restricting the exhaust flow in a silencer? A : Baffle type B : Electronic type C : Resonance type D : Reverse flow type

279 : Where is turbocharger mounted? A : Exhaust manifold B : Inlet manifold C : Air cleaner D : Cylinder head

280 : Name the drive of turbo charger. A : Engine drive B : Electric motor drive C : Exhaust gas pressure D : Compressed air

281 : Name the part marked as ‘x’.

A : Turbine unit B : Compressor unit C : Exhauster unit D : Charger unit

282 : Where the turbo charger compressor housing outlet connected? A : Connected to air cleaner B : Connected to inlet-manifold C : Connected to exhaust - manifold D : Connected to oil filter

283 : Name the type of muffler.

A : Reverse flow muffler B : Straight through muffler C : Baffle type muffler D : Electronic muffler







286 : What material is used for manufacturing exhaust manifold? A : Cast iron B : Aluminium alloy C : Copper D : Steel

287 : What is the material generally used for manufacturing inlet manifold? A : Aluminium alloy B : Copper C : Steel D : Plastic

288 : Which type of muffler produces anti noise without restricting the exhaust flow in a silencer? A : Baffle type B : Electronic type C : Resonance type D : Reverse flow type

289 : Which type of muffler is fitted with sensors, microphone and speakers? A : Baffle type muffler B : Reverse flow type muffler C : Electronics type muffler D : Straight through muffler

290 : What is the reason for decrease the volumetric efficiency in the exhaust system? A : Low noise B : High temperature C : Excessive back pressure D : Low temperature

291 : How the CRDI injectors pressure control valve operated? A : Mechanically B : Electronically C : Manually D : Hydraulic

292 : Where is the pressure discharge valve fitted in CRDI fuel system? A : Common rail B : Fuel pump C : Injectors D : Fuel filter

293 : How many fuel chamber’s are in HEUI? A : One B : Two C : Three D : Four

294 : Which is develop diesel pressure in the CRDI engine A : ECM B : Injection C : Fuel tank D : High pressure pump



295 : Which type of pump ensures in built and uniform delivery to all injectors in diesel engine? A : Jerk type pump B : In line pump C : Rotary type pump D : Servo type pump

296 : Which fuel related with cetane number? A : Petrol B : Diesel C : Coal D : Kerosene

297 : Where the diesel fuel is obtained? A : Crude oil B : Vegetable oil C : Animal oil D : Synthetic oil

298 : Which fuel pipe line is provided between fuel filter and injectors? A : Suction pipe B : Pressure pipe C : Vacuum pipe D : Over flow pipe

299 : What is the name of nozzle?

A : Single hole nozzle B : Multi hole nozzle C : Pintle nozzle D : Pintaux nozzle

300 : Which part is atomise the fuel into engine cylinder? A : Injector B : FIP C : Governor D : Feed pump

301 : Which type of fuel system is best suited for less fuel consumption, more power and reduce the exhaust emission? A : Inline pump system B : Rotary pump system C : Distributor pump system D : CRDI system

302 : What is the advantages of CRDI system? A : Increase engine noisy B : Reduce the engine torque C : Increase fuel consumption D : Above 25% of power developed

303 : Which is develop diesel pressure in the CRDI engine A : ECM B : Injection C : Fuel tank D : High pressure pump

304 : How much maximum pressure, develops by high pressure diesel pump in CRDI engine A : 500 Kg/cm2 B : 800 Kg/cm2 C : 2000 Kg/cm2 D : 1600 Kg/cm2

305 : Which feed system reduces above 50% unburnt hydro carbon? A : In line fuel injection system B : Distributor fuel injection system C : Electronic control system D : Air blast fuel injection system

306 : Which type of fuel system has high pressure oil pump in diesel engine? A : Inline FIP B : Rotary FIP C : CRDI fuel system D : HEUI fuel system



307 : Why fuel filter is essential in diesel engine? A : Increase the power B : Prevent dirty smoke C : Easy starting D : Mirror polishing finish in nozzle and FIP

Mechanic Agriculture Machinery– 1st year Module 9 - Transmission and Steering system



308 : What is the name of part marked as ‘X’ in dual clutch?

A : Clutch guard B : Disc spring C : Disc spring D : PTO pressure ring plate

309 : What is the name of part marked as ‘X’ in clutch plate?

A : Lining B : Torque plate C : Torque plate D : Cushion spring

310 : Which part of the transmission system connect and disconnect the power from the engine? A : Gear box B : Clutch C : Clutch D : Universal joint

311 : Which part of the transmission system transmit the power from engine to gear box?

A : Clutch B : Final drive C : Final drive D : Transfer case

312 : What is the name of gear box?

A : Sliding mesh gear box B : Synchro mesh gear box C : Synchro mesh gear box D : Epicyclic gear box

313 : What is the name of part marked as ‘X’ in gear shift mechanism?

A : Shifter locks B : Shift lever C : Shift lever D : Selector rod




314 : What is the name of part marked as ‘X’ in collar shift transmission?

A : Shaft B : Driven gear C : Driven gear D : Shifter sleeve

315 : Which assembly used to transfer the engine power to front and rear axle wheels? A : Main gear box B : Auxiliary gear box C : Auxiliary gear box D : Winch gear box

316 : Which type of gear box consists with annular and planet gears? A : Constant mesh gear box B : Sliding mesh gear box C : Sliding mesh gear box D : Synchro mesh gear box

317 : What is the name of part marked as ‘X’ in transfer case?

A : Output shaft gear B : Output high gear

C : Output high gear D : Reverse gear

318 : Which part of the differential unit support the axle pinion shaft? A : Star gear B : Ring gear C : Ring gear D : Drive pinion

319 : Which is the precaution of differential lock at use? A : Do not use more than ten seconds B : Don’t turn the vehicle with differential lock C : Don’t turn the vehicle with differential lock D : Engage differential lock on turn

320 : Which part of the differential prevents the loss of power? A : Drive pinion B : Axial shaft C : Axial shaft D : Shift lock

321 : Which part of the differential is idle on their axis during straight line run? A : Drive pinion B : Ring gear C : Ring gear D : Sun gear

322 : Which part of the differential unit rotate the cage flange in tractor? A : Drive pinion B : Ring gear C : Ring gear D : Sun gear




323 : What is the name of part marked as ‘X’ in front axle?

A : Stub axle B : Axle beam C : Axle beam D : Drop arm

324 : What is the name of stub axle?

A : Elliot B : Lemoin C : Lemoin D : Reversed lemoin

325 : What is the type of stub axle?

A : Reverse lemoin type B : Lemoin type C : Lemoin type D : Reverse Elliot type

326 : What is the name of part marked as ‘X’ in steering mechanism?

A : Drop arm B : Drag link rod C : Drag link rod D : Track rod

327 : Which type of steering gear box used in wheeled tractors? A : Rack and pinion type B : Cam and peg type C : Cam and peg type D : Worm and roller type




328 : What is the name of part marked as ‘X’ in steering mechanism?

A : Tie rod B : Drag link C : Drag link D : Steering arm

329 : What is the name of part marked as ‘X’ in worm and roller type steering mechanism?

A : Drag link B : Steering column

C : Steering column D : Drop arm

330 : Which type of stub axle is mounted on the top of the tractor axle beam? A : Reverse Elliot type B : Lemoin type C : Lemoin type D : Reverse lemoin type

331 : What is the name of part marked as ‘X’ in electronic power steering system?

A : Controller B : Torque sensor C : Torque sensor D : Steering torque




332 : What is the type of power assisted steering system?

A : Manual steering B : Integral steering C : Integral steering D : Electronic power steering

333 : Which part of the steering system used by driver to change the direction of tractor front wheel? A : Steering wheel B : Drag link rod C : Drag link rod D : Track rod

334 : How to prevent the oil leakage from the steering gear box? A : By sealing wax B : By sealing compound C : By sealing compound D : By bearing retainer

Mechanic Agriculture Machinery– 1st year Module 10 - Wheels, Tyres and Brake system



335 : What is the type of wheel?

A : Light alloy wheel B : Split wheel C : Wire wheel D : Heavy vehicle wheel

336 : What is the name of wheel rim?

A : Wire wheel rim B : Split wheel rim C : Flat type rim D : Light alloy wheel rim

337 : What is the name of wheel rim?

A : Split wheel rim B : Wire wheel rim C : Flat wheel rim D : Light alloy wheel rim

338 : What is the name of tyre defects?

A : Bald spots B : Cracked treads C : Rapid wear at centre D : Rapid wear at shoulder




339 : What is the name of arrow marked defects in tyre?

A : Bald spots B : Cracked treads C : Wear on one side D : Rapid wear at centre

340 : What is the name of tyre defect?

A : Bald spots wear B : Feathered edge C : Scalloped wear D : Cracked tread

341 : What is the name of arrow marked tyre defects?

A : Cracked treads B : Bald spots wear C : Wear on one side D : Scalloped wear

342 : What is the name of arrow marked tyre defects?

A : Cracked treads B : Feathered edge C : Bald spots wear D : Rapid wear at shoulders




343 : What is the name of part marked as ‘X’ in tyre?

A : Plies B : Tread C : Casing D : Beads

344 : Which component of tyre resist to cut? A : Beads B : Casing C : Tread D : Side walls

345 : What represent the number 28 in tyre mark 12.6 X 28? A : Plies rating B : Rim diameter C : Cross section width D : Tyre wall thickness

346 : Which type of metal wire provided in the inner edge of tyres?

A : Brass wire B : Steel wire C : Aluminium wire D : Lead wire

347 : What is the advantage of tube less tyres? A : Tyre life is short B : Less period of air holding C : Suitable for wire wheel rim D : Seal a puncture without removing

348 : What denotes 145 of tyre number 14570R13? A : Diameter B : Height C : Width D : Radial

349 : Which prevent the uneven wear of tyres? A : Tyre rotation B : Tyre over inflation C : Tyre under inflation D : Use of tubeless tyre

350 : Which is strengthen the tyre casing with wheel? A : Beads B : Plies C : Tube flap D : Inflation pressure

351 : Which part of the tyre absorb the sudden shocks from rough surface? A : Casing B : Treads C : Breakers D : Beads

352 : Which part of the tyre anchor with rim? A : Casing B : Tread C : Beads D : Side wall

353 : How much percentage of water used in rear tube for ballasting? A : 45% B : 55% C : 65% D : 75%




354 : Which part of the tyre is flexible on sudden shock? A : Treads B : Plies C : Breakers D : Side walls

355 : Which protects the tube damage by the rim? A : Tread B : Casing C : Flap D : Beads

356 : What is the purpose of foot brake in tractor? A : To start the engine B : To stop the engine C : To stop the vehicle D : To connect the implements

357 : Which part of hydraulic brake acts against the drum force? A : Master cylinder B : Wheel cylinder C : Brake pedal D : Brake shoes

358 : Which type of wheel has two separate discs and clamped together with nut and bolt? A : Flat rim B : Wire wheel rim C : Split wheel rim D : Light alloy wheel rim

359 : Which device is used to adjust the clearance between the brake shoe and drum in air brake system? A : Brake chamber B : Slack adjuster C : Brake valve D : Unloader valve

360 : What is the practice in hydraulic brake system?

A : Top up the wheel cylinder B : Remove the excessive fluid C : Remove air from brake system D : Top up the master cylinder

361 : What is the cause for spongy brake pedal in hydraulic brake? A : Fluid viscosity low B : Air enter in the system C : Master cylinder cap vent hole open D : Dirty brake fluid

362 : What indicate the wheel arrow mark?

A : Wheel alignment B : Wheel balancing C : Wheel rotation D : Wheel defects




363 : Which part of the mechanical brake expands the brake shoe? A : Brake pedal B : Brake linkage C : Brake cam D : Brake drum

364 : What is the disadvantage of hydraulic brake? A : More wear of parts B : Equal braking in all wheels C : Little maintenance need D : Fluid leakage leads brake safeless

365 : What is the name of brake system?

A : Pneumatic brake B : Mechanical brake C : Band type parking brake D : Vacuum booster hydraulic brake

366 : Which device is used to adjust the clearance between the brake shoe and drum in air brake system? A : Brake chamber B : Slack adjuster C : Brake valve D : Unloader valve

367 : What is the name of part marked as ‘X’ in brake system?

A : Brake pedal B : Master cylinder C : Wheel cylinder D : Brake shoe

Mechanic Agriculture Machinery– 1st year Module 11 - Agriculture Implements Service of Charging and Starting system



368 : What is the name of part marked as ‘X’ is power tiller?

A : Chassis B : Tensioner C : Front stand D : Handle stay

369 : What is the name of part marked as ‘X’ in power tiller?

A : Chassis B : Tensioner C : Handle stay D : Rota tiller assembly

370 : What is the name of part marked as ‘X’ in rota tiller assembly?

A : Tyne B : Sprocket C : Bearing D : Rotary shaft

371 : What is the name of part marked as ‘X’ in rota tiller assembly?

A : Gear box B : Wheel hub C : Sprocket D : Chassis frame

372 : What is the purpose of the power tiller? A : Used for rock drilling B : Used for agricultural implements C : Used to pull heavy loads D : Used passenger transportation




373 : Which equipment is attached with power tiller for transportation purpose? A : Crawler B : Trolley C : Trailer D : Bucket

374 : What is the name of part marked as ‘X’ in single point hitch?

A : Quadrant B : Hitch pin C : Hitch bar D : Hitch point


A : Draw bar B : Lower links C : Stay links D : Hitch bar

376 : What is the name of hitch system?

A : Single point hitch B : Two point hitch C : Three point hitch D : Four point hitch




377 : What is the name of hitch system?

A : Single point hitch B : Two point hitch C : Three point hitch D : Four point hitch

378 : What is the name of part marked as ‘X’ in three point hitch?

A : Lower links B : Upper links C : Adjustable screw type top link D : Hitching point


A : Hitch bar B : Draw bar C : Stay links D : Lower links

380 : Which agriculture implement used to create soil for preservation of mixture from subsoil? A : Disc harrows B : Rotary grass mower C : Ridger D : PTO shaft

381 : What is the cause for belt slippage in tractor? A : Pulley to high B : Oil or grease on belt C : Pulleys too near D : Belt tension too high




382 : What is to be checked before hitching the disc plough?

A : Disc width B : Disc sharpness C : Disc weight D : Disc height

383 : What is the name of device? A : Disc plough B : Harvester C : Thresher D : Ridger

384 : Which agriculture implement is used to break the hard crust of the top soil and prevent into depth? A : Harvester B : Seed drilling machine C : Disc harrow D : Rotavator

385 : Which agriculture implement used to create soil for preservation of mixture from subsoil? A : Disc harrows B : Rotary grass mower C : Ridger D : PTO shaft

386 : Which part of the farm tractor takes care wide range of variation in the field condition? A : Hitch point B : Lower link C : Upper link D : Swinging draw bar

387 : What is the solution to full fill the shortage of human and animal source in farm works? A : Chemical power source B : Mechanical power source C : Electrical power source D : Hydraulic power source

388 : What is the cause for engine does not crank? A : Defective alternator B : Defective light switch C : Defective fog light D : Discharged battery

389 : What is the cause for engine does not crank even batteries in good condition? A : Alternator defective B : Starter motor pinion worn out C : Voltage regular defective D : Wiper motor defective




ANSWERS :

1:D; 2:A; 3:C; 4:A; 5:A; 6:B; 7:B; 8:A; 9:D; 10:D; 11:D; 12:D; 13:C; 14:D; 15:D; 16:A; 17:D; 18:C; 19:A; 20:A; 21:C; 22:B; 23:B; 24:A; 25:C; 26:B; 27:B; 28:D; 29:B; 30:A; 31:A; 32:B; 33:C; 34:A; 35:A; 36:D; 37:B; 38:C; 39:A; 40:D; 41:A; 42:B; 43:A; 44:C; 45:C; 46:A; 47:D; 48:C; 49:D; 50:D; 51:C; 52:B; 53:A; 54:B; 55:B; 56:A; 57:D; 58:A; 59:D; 60:B; 61:A; 62:C; 63:A; 64:D; 65:C; 66:C; 67:D; 68:D; 69:B; 70:C; 71:B; 72:A; 73:C; 74:C; 75:B; 76:A; 77:D; 78:D; 79:B; 80:C; 81:C; 82:B; 83:D; 84:A; 85:A; 86:D; 87:C; 88:C; 89:C; 90:A; 91:C; 92:B; 93:B; 94:A; 95:C; 96:D; 97:D; 98:C; 99:B; 100:A; 101:A; 102:A; 103:C; 104:D; 105:B; 106:B; 107:C; 108:B; 109:A; 110:B; 111:A; 112:A; 113:D; 114:D; 115:B; 116:A; 117:B; 118:A; 119:C; 120:A; 121:C; 122:B; 123:B; 124:B; 125:A; 126:D; 127:A; 128:D; 129:C; 130:D; 131:C; 132:D; 133:D; 134:A; 135:B; 136:B; 137:A; 138:C; 139:C; 140:D; 141:C; 142:B; 143:A; 144:C; 145:A; 146:A; 147:A; 148:D; 149:C; 150:A; 151:A; 152:C; 153:B; 154:C; 155:C; 156:B; 157:B; 158:A; 159:B; 160:B; 161:A; 162:D; 163:B; 164:A; 165:A; 166:A; 167:B; 168:C; 169:C; 170:C; 171:A; 172:D; 173:C; 174:C; 175:D; 176:D; 177:A; 178:C; 179:D; 180:A; 181:D; 182:B; 183:C; 184:B; 185:C; 186:A; 187:C; 188:D; 189:C; 190:A; 191:C; 192:C; 193:B; 194:C; 195:A; 196:C; 197:B; 198:C; 199:C; 200:C; 201:C; 202:B; 203:A; 204:C; 205:A; 206:B; 207:D; 208:A; 209:D; 210:D; 211:D; 212:A; 213:B; 214:D; 215:B; 216:B; 217:C; 218:B; 219:D; 220:D; 221:C; 222:C; 223:B; 224:C; 225:B; 226:A; 227:D; 228:C; 229:D; 230:A; 231:B; 232:C; 233:D; 234:A; 235:A; 236:C; 237:A; 238:C; 239:B; 240:B; 241:D; 242:D; 243:A; 244:A; 245:C; 246:B; 247:D; 248:C; 249:D; 250:A; 251:A; 252:D; 253:A; 254:A; 255:C; 256:B; 257:C; 258:B; 259:C; 260:D ; 261:A; 262:B; 263:A; 264:D; 265:A; 266:D; 267:C; 268:D; 269:C; 270:D; 271:A; 272:C; 273:B; 274:D; 275:A; 276:B; 277:C; 278:B; 279:A; 280:C; 281:B; 282:B; 283:A; 284:B; 285:C; 286:A; 287:A; 288:B; 289:C; 290:C; 291:B; 292:A; 293:B; 294:D; 295:C; 296:B; 297:A; 298:D; 299:A; 300:A; 301:D; 302:D; 303:D; 304:C; 305:C; 306:C; 307:B; 308:A; 309:B; 310:B; 311:A; 312:D; 313:D; 314:C; 315:B; 316:C; 317:C; 318:C; 319:B; 320:C; 321:C; 322:B; 323:B; 324:A; 325:D; 326:B; 327:D; 328:C; 329:B; 330:B; 331:B; 332:D; 333:A; 334:C; 335:C; 336:B; 337:C; 338:C; 339:C; 340:A; 341:D; 342:D; 343:A; 344:C; 345:B; 346:B; 347:D; 348:C; 349:A; 350:D; 351:C; 352:C; 353:D; 354:D; 355:C; 356:C; 357:D; 358:C; 359:B;

360:C; 361:B; 362:C; 363:C; 364:D; 365:D; 366:B; 367:B; 368:D; 369:D; 370:A; 371:C; 372:B; 373:B; 374:C; 375:C; 376:B; 377:C; 378:C; 379:B; 380:A; 381:B; 382:B; 383:A; 384:C; 385:A; 386:D; 387:B; 388:D; 389:B;

mechanic agriculture machinery 1st year module 1 - safety … · 2020-01-10 · 66 : what is the...

Documents