mechanical anchoring systems · pdf filemechanical anchoring systems ... (ldt ™)...

Red HeadMechanical Anchoring Systems

The Red Head product line has long been respected by both contractors and specifiers in the constructionindustry. Because ITW Ramset/Red Head proactivelygets Red Head products specified before the job starts,contractors save time and money, plus the hassle of getting products approved. We will continue to pursuecode approvals for specific anchor usages.

Red Head has also been on the forefront of concrete anchoring industry innovation and development.

For example, we

Red Head is committed to providing contractors withquality products and developing new products to meetthe demands of contractors worldwide.

Since 1910, the brand trusted by the construction industry for quality, innovation and engineering support

| developed the first anchor (the Self-Drill in 1910)

| developed the fully-threaded Trubolt ® Wedge anchor with a stainless steel clip

| developed the lipped Multi-Set II® anchor

| helped develop (as part of ITW) markets for Tapcon® and E-Z Ancor™

| were one of the first manufacturers to achieve ISO9002 certification

58 Call our toll free number 800-899-7890 or visit our web site for the most current product and technical information at www.ramset-redhead.com

Selection Guide

Anchors for Concrete Applications

Diameter: 1/4 – 1

Length: 1-3/4 – 12

Diameter: 1/4 – 3/4

Length: 5/8 – 6-1/4


Length: 1-3/4 – 6-1/4

■ Fully-threaded

■ Length ID head stamped

■ Stainless steel clip

■ Through-fixture fastening

■ Concrete, block and brick

■ Many choices of head styles


■ Available in 304 stainless steel


Length: 2 – 7

■ Special design clamps down base plates

■ Finished head, heavy duty sleeve anchor

■ Removable

■ Available in carbon steel and 316 stainless steel

■ Concrete, block or brick

(see page 86)

■ Bottom bearing

■ Hammer-driven

■ Ideal for jacking or leveling

■ Easy installation

(see page 82)

Trubolt®Wedge Anchors

(see page 62)

ANCHOR TYPE KEY FEATURES SIZE RANGE (Inches)

Dynabolt®

Masonry Sleeve Anchors

(see page 73)

Stud™

Stud Anchors

Diameter: 1/4 – 3/4Length: 1 – 3-3/16Same as RM (above)Diameter: 3/8 Length: 3/4Diameter: 1/2 & 3/4Length: 2 & 3-3/16

■ RM: Flanged body to keep anchor flush with surface of concrete

■ RL: Non-flanged body for recessed setting

■ RX: Designed for hollow core and post tension concrete

■ CL: Designed for one-sided forming, accepts coil rodRM RL RX CL

Multi-Set II®Drop-In Anchors

Diameter: 3/8 and 1/2

Length: 1-3/4 – 5

■ Anti-rotation serrated washer

■ Extra large hex washer head

■ Length ID head stamped

■ GRD2000™ exterior coating*(= 1,000 hour salt spray)

■ Dust relief tip

Dynabolt GoldMasonry Sleeve Anchors

* Special order

Large Diameter Tapcon(LDT™)Self-Threading Anchor

(see page 68)

(see page 78)

For both Hollow and Solid Concrete Applications

59Call our toll free number 800-899-7890 or visit our web site for the most current product and technical information at www.ramset-redhead.com

Hex nutTie-Wire version

FF-S-325 Group II, Type 4, Class 1Underwriters LaboratoriesFactory MutualICBO Evaluation Service, Inc. – #ER-1372City of Los Angeles – #RR2748SBCCI Compliance Report – #9570California State Fire MarshalCal TransMetro-Dade County – #01-0504.12

RM: Flanged bodyRL: Non-flanged bodyUse any bolt or threaded rod

FF-S-325 Group VIII, Type 1Underwriters LaboratoriesFactory MutualICBO Evaluation Service, Inc. – #ER-1372City of Los Angeles – #RR2748SBCCI Compliance Report – #9570California State Fire MarshalCal Trans

Flat headHex nutAcorn nutTie-WireRound headThreshold flat headHex coupling

FF-S-325 Group II, Type 3, Class 3Factory MutualSBCCI Compliance Report – #9570California State Fire Marshal

Hex nut FF-S-325 Group VIII, Type 2SBCCI Compliance Report – #9570Factory MutualUnderwriters LaboratoriesCalifornia State Fire Marshal

Ultimate PulloutPerformance in 4000 psi Concreteup to 43,300 lbs.

Ultimate PulloutPerformance in4000 psi Concreteup to 9,480 lbs.


Dynaboltcont’d

CORROSION RESISTANCE PERFORMANCE HEAD STYLES APPROVALS/LISTINGS


Studcont’d

continued on next page

■ Zinc-plated carbon steel to ASTM B633, SC1, Type III


■ Type 304 stainless steel


■ Type 18-8 and 316 stainless steel


■ Hot dipped galvanized to ASTM A-153

■ Type 304 and 316 stainless steel

Multi-Set IIDrop-Incont’d

Finished headHex bolt

FF-S-325 Group II, Type 3, Class 1Ultimate PulloutPerformance in4000 psi Concreteup to 18,000 lbs.

■ Zinc-plated carbon steel to ASTM B633, SC1, Type II


DynaboltGoldcont’d

Selection Guide

LDTcont’d

■ Zinc-plated carbon steel to ASTM B695


Ultimate PulloutPerformance in4,000 psi Concreteup to 12,070 lbs.

Finished bolt style ICBO Evaluation Service, Inc. – #ER-5890City of Los Angeles – #RR25498

Truboltcont’d


Anchors for Concrete Applicationscontinued from pages 58-59

■ Simple installation

■ Small drill size

■ No torque required


Diameter: 1/4

Length: 3/4 – 3

Diameter: 3/16 & 1/4

Length: 1-1/4 – 6

Diameter: 3/16 & 1/4

Length: 7/8 – 2


Length: 1-1/4 – 1-7/16

3/16" uses #6 – 8 screw

1/4" uses #10 – 12 screw

■ Fast installation with Condrive tool

■ Removable

■ Cuts own threads

■ Bit included in every box



■ Low profile head


Hammer-Set™

Nail-drive Anchors

■ Unique twisting action

■ Resistant to moisture, chemicals andatmospheric conditions

■ Available in pre-packaged kits

Poly-Set®

All-purpose plastic plug anchors


Anchors for Hollow and Drywall Applications


Length: 1-1/4 – 1-7/16

3/16" uses #6 – 8 screw

1/4" uses #10 – 12 screw

■ Unique twisting action

■ Resistant to moisture, chemicalsand atmospheric conditions

■ Available in pre-packaged kits

Accepts #8 and #10 screws■ Fast, no pre-drilling

■ Easy to use, just use #2 phillips bit

■ Removable

(see page 97)

(see page 88)

Redi-Drive®

High performance Hammer-Drive Anchors

(see page 92)

(see page 99)

Diameter: 3/16 & 5/16

Length: 1 – 4

■ Easy—through fixture fastening

■ Removable

■ Low profile head with large bearing surfaces

Nylon-DriveAnchors

(see page 99)

(see page 102)

Tapcon®

Self-tappingConcrete Anchors

(see page 102)

E-Z Ancor™Drywall Anchors

Poly-Set®

All-purpose plastic plug anchors




For both Hollow and Drywall Applications

For Drywall Applications Only



Mushroom headPipe version (1/4" & 3/8")Tie-Wire versionForm-drive

FF-S-325 Group VIFactory Mutual (3/8" Pipe-Drive)

Hex headPhillips flat head

ICBO Evaluation Service, Inc.– #ER-3370Metro-Dade County – #00-0118.02City of Los Angeles – #RR24953

Mushroom head FF-S-325, Group V, Type 2, Class 3

Kit comes withphillips head screw(accepts screw styleof your choice)


Ultimate PulloutPerformance in4000 psi Concreteup to 793 lbs.



Kit comes with phillipshead screw (accepts screwstyle of your choice)

Accepts screw style ofyour choice

Ultimate PulloutPerformance in 5/8"Gypsum wallboardup to 75 lbs.

■ Zinc-plated carbon steel toASTM B695

■ Patented Climaseal® coating


■ Zinc alloy

■ Polyethylene Anchor

(accepts corrosion resistantscrew of your choice)

■ Polyethylene Anchor


■ Zinc plated steel/engineered plastic


Redi-Drivecont’d

E-Z Ancorcont’d

Tapconcont’d

Poly-Setcont’d

Selection Guide cont’d

Hammer-Setcont’d

Phillips flat head■ Nail is made of Zinc-plated carbon steel to ASTM B633, SC1

■ Anchor body is made fromPolyamide 6.6

Nylon-Drivecont’d

Ultimate PulloutPerformance in2000 psi Concreteup to 670 lbs.

Poly-Setcont’d


ADVANTAGES■ Versatile fully threaded design is standard

on sizes up to 3/4" diameter and 10" length

■ Anchor diameter equals hole diameter

■ One piece stainless steel expander clipresists corrosion

■ Standard or carbon and stainless steel anchors

■ 360° contact with concrete assures full expansion for reliable working loads

■ Non bottom-bearing, may be used in holedepth exceeding anchor length

■ Can be installed through the work fixture, eliminating hole spotting

■ Inspectable torque values, indicating proper installation

Trubolt’s fully threaded feature eliminates subsurfaceobstruction problems.

Fully threaded design accommodates various material thicknesses at the same embedment. One anchor length saves time and money.

Dependable,Heavy-Duty,Inspectable,Wedge Type

ExpansionAnchor

DESCRIPTION/SUGGESTED SPECIFICATIONS

Wedge Type Anchors— SPECIFIED FOR ANCHORAGE INTO CONCRETE

Wedge anchors feature a type 18-8 stainless steel split expansion ring and a threaded stud bolt body and integral cone expander, nut and washer. Anchor bodies are made of plated carbon steel, hot-dipped

galvanized carbon steel, type 304 stainless steel or type 316 stainless steelas identified in the drawings or other notations.

The exposed end of the anchor is stamped to identify anchor length.Stampings should be preserved during installation for any subsequentembedment verification.

Use carbide tipped hammer drill bits made in accordance to ANSI B212.15-1994 to install anchors.

Anchors are tested to ASTM E488 criteria and listed by ICBO and SBCCI. Anchors are listed by the followingagencies as required by the local building code: UL, FM, City of Los Angeles, California State Fire Marshal and Cal Trans.

TruboltWedgeAnchor

Fully ThreadedAdvantage

TruboltWedge Anchors

®


1. Using a bit whose diameter equals the anchordiameter, drill hole to any depth exceeding theminimum embedment. Clean hole.

2. Assemble anchor with nut and washer so that the top of the nut is flush with the top of theanchor. Drive anchor through material to be fastened so that nut and washer are flush with surface of material.

INSTALLATION STEPS

3. Expand anchor by tightening nut 3 to 5 turns, or to the specific torque requirement(see selection chart).

Trubolt Anchors

APPLICATIONS

FEATURES

Anchoring machinery and conveyors is a common wedge anchor application.The Trubolt is fully threaded to allow alarge range of embedment and fixture thickness.

Safety railings are commonly anchoredwith Trubolt wedge anchors because ofavailability in four material types for all corrosive atmospheres.

Pre-cast panels are typically anchored tothe concrete slab temporarily with Truboltwedge anchors because of reliable performance and economical pricing.

APPROVALS/LISTINGSMeets or exceeds U.S. Government G.S.A. Specification FF-S-325 Group II,Type 4, Class 1

Underwriters Laboratories

Factory Mutual

ICBO Evaluation Service, Inc. – #ER-1372(including seismic loading conditions)

Metro-Dade County – #01-0504.12

City of Los Angeles – #RR2748

SBCCI Compliance Report – #9570

California State Fire Marshal

Cal Trans

LENGTH INDICATION CODE*CODE LENGTH OF ANCHOR CODE LENGTH OF ANCHOR

A 1-1/2 < 2 (38.1 < 50.8) K 6-1/2 < 7 (165.1 < 177.8)B 2 < 2-1/2 (50.8 < 63.5) L 7 < 7-1/2 (177.8 < 190.5)C 2-1/2 < 3 (63.5 < 76.2) M 7-1/2 < 8 (190.5 < 203.2)D 3 < 3-1/2 (76.2 < 88.9) N 8 < 8-1/2 (203.2 < 215.9)E 3-1/2 < 4 (88.9 < 101.6) O 8-1/2 < 9 (215.9 < 228.6)F 4 < 4-1/2 (101.6 < 114.3) P 9 < 9-1/2 (228.6 < 241.3)G 4-1/2 < 5 (114.3 < 127.0) Q 9-1/2 < 10 (241.3 < 254.0)H 5 < 5-1/2 (127.0 < 139.7) R 10 < 11 (254.0 < 279.4)I 5-1/2 < 6 (139.7 < 152.4) S 11 < 12 (279.4 < 304.8)J 6 < 6-1/2 (152.4 < 165.1) T 12 < 13 (304.8 < 330.2)

*Located on top of anchor for easy inspection.

Length ID Head Stamp—provides for embedment inspection after installation

Fully Threaded Design

Cold-Formed—manufacturing processadds strength

Type 18-8 stainless steel split expansion ring

Anchor Body—available in zinc-platedsteel, hot-dipped galvanized steel, 304 stainless steel and 316 stainless steel


Trubolt Carbon Steelwith Zinc Plating

PART THREAD ANCHOR DIA. OVERALL MAX. QTY/WT QTY/WTNUMBER LENGTH & DRILL BIT LENGTH THICKNESS PER BOX PER MASTER

In. (mm) SIZE (THREADS) In. (mm) OF MATERIAL lbs. CARTONPER INCH TO BE FASTENED lbs.

In. (mm)

WS-1416 3/4 (19.1) 1/4" - 20 1-3/4 (44.5) 3/8 (9.5) 100/ 3.1 1000/ 32WS-1422 1-1/4 (31.8) 2-1/4 (57.2) 7/8 (22.2) 100/ 3.6 1000/ 37WS-1432 2-1/4 (57.2) 3-1/4 (82.6) 1-7/8 (47.6) 100/ 4.7 800/ 39WS-3822 1-1/8 (28.6) 3/8" - 16 2-1/4 (57.2) 3/8 (9.5) 50/ 4.1 500/ 41WS-3826 1-5/8 (41.3) 2-3/4 (69.9) 7/8 (22.2) 50/ 4.7 400/ 39WS-3830 1-3/4 (44.5) 3 (76.2) 1-1/8 (28.6) 50/ 5.0 400/ 41WS-3836 2-1/2 (63.5) 3-3/4 (95.3) 1-7/8 (47.6) 50/ 5.9 300/ 36WS-3850 3-3/4 (95.2) 5 (127.0) 3-1/8 (79.4) 50/ 7.4 250/ 38WS-3870 2-1/4 (57.2) 7 (177.8) 5-1/8 (130.2) 50/ 10.4 250/ 53WS-1226 1-1/4 (31.8) 1/2" - 13 2-3/4 (69.9) 1/8 (3.2) 25/ 4.6 200/ 38WS-1236 2-1/4 (57.2) 3-3/4 (95.3) 1 (25.4) 25/ 5.7 150/ 35WS-1242 2-3/4 (69.9) 4-1/4 (108.0) 1-1/2 (38.1) 25/ 6.2 150/ 38WS-1244 3 (76.2) 4-1/2 (114.3) 1-3/4 (44.5) 25/ 6.5 150/ 39WS-1254 3 (76.2) 5-1/2 (139.7) 2-3/4 (69.9) 25/ 7.7 150/ 47WS-1270 4-1/2 (114.3) 7 (177.8) 4-1/4 (108.0) 25/ 9.3 150/ 57WS-5834 1-3/4 (44.5) 5/8" - 11 3-1/2 (88.9) 1/8 (3.2) 10/ 3.6 100/ 37WS-5842 2-1/2 (63.5) 4-1/4 (108.0) 7/8 (22.2) 10/ 4.1 100/ 42WS-5850 3-1/4 (82.6) 5 (127.0) 1-5/8 (41.3) 10/ 4.7 100/ 48WS-5860 4-1/4 (107.9) 6 (152.4) 2-5/8 (66.7) 10/ 5.4 50/ 28WS-5870 5-1/4 (133.4) 7 (177.8) 3-5/8 (92.1) 10/ 6.2 30/ 19WS-5884 5-3/4 (146.0) 8-1/2 (215.9) 5-1/8 (130.2) 10/ 8.0 30/ 25WS-58100 5-3/4 (146.0) 10 (254.0) 6-5/8 (168.3) 10/ 9.4 30/ 29WS-3442 1-3/4 (44.5) 3/4" - 10 4-1/4 (108.0) 1/4 (31.8) 10/ 6.8 60/ 42WS-3446 2-1/4 (57.2) 4-3/4 (120.7) 3/4 (19.1) 10/ 7.4 60/ 45WS-3454 3 (76.2) 5-1/2 (139.7) 1-1/2 (38.1) 10/ 8.1 50/ 41WS-3462 3-3/4 (95.3) 6-1/4 (158.8) 2-1/4 (57.2) 10/ 9.1 30/ 28WS-3470 4-1/2 (114.3) 7 (177.8) 3 (76.2) 10/ 9.7 30/ 30WS-3484 5-3/4 (146.0) 8-1/2 (215.9) 4-1/2 (114.3) 10/ 12.3 30/ 38WS-34100 5-3/4 (146.0) 10 (254.0) 6 (152.4) 10/ 14.0 30/ 43WS-34120 1-3/4 (44.5) 12 (304.8) 8 (203.2) 10/ 16.6 30/ 51WS-7860 2-1/2 (63.5) 7/8" - 9 6 (152.4) 1-3/8 (34.9) 5/ 6.3 25/ 32WS-7880 2-1/2 (63.5) 8 (203.2) 3-3/8 (85.7) 5/ 8.1 15/ 25WS-78100 2-1/2 (63.5) 10 (254.0) 5-3/8 (136.5) 5/ 9.8 15/ 30WS-10060 2-1/2 (63.5) 1" - 8 6 (152.4) 1/2 (12.7) 5/ 8.3 25/ 43WS-10090 2-1/2 (63.5) 9 (228.6) 3-1/2 (88.9) 5/ 11.6 15/ 36WS-100120 2-1/2 (63.5) 12 (304.8) 6-1/2 (165.1) 5/ 15.0 15/ 46TIE WIRETW-1400 N/A 1/4" - 20 2-3/16 (55.6) 9/32-hole (7.1) 100/ 3.6 1000/ 36

Typical Applications—Structural Columns, Machinery, Equipment, etc.

Environment—Interior (non-corrosive)

Level of Corrosion—Low

Meets ASTM B633 SC1, Type III specifications for electroplating of 5um = .0002" thickness. This material is well suited for non-corrosive environments.

Typical Applications—Railings, Signage, Awnings, etc.

Environment—Rural/Suburban(exterior environment—essentially unpolluted areas)

Level of Corrosion—Low to Medium

Trubolt Carbon Steelwith Hot-Dipped Galvanizing



In. (mm)

WS-1226G 1-1/4 (31.8) 1/2" - 13 2-3/4 (69.9) 1/8 (3.2) 25/ 4.8 200/ 39WS-1242G 2-3/4 (69.9) 4-1/4 (108.0) 1-1/2 (38.1) 25/ 6.7 150/ 41WS-1254G 3 (76.2) 5-1/2 (139.7) 2-3/4 (69.9) 25/ 8.0 150/ 49WS-1270G 4-1/2 (114.3) 7 (177.8) 4-1/4 (108.0) 25/ 9.7 150/ 59WS-5834G 1-3/4 (44.5) 5/8" - 11 3-1/2 (88.9) 1/8 (3.2) 10/ 3.7 100/ 38WS-5860G 4-1/4 (107.9) 6 (152.4) 2-5/8 (66.7) 10/ 5.6 50/ 29WS-3446G 2-1/4 (57.2) 3/4" - 10 4-3/4 (120.7) 3/4 (19.1) 10/ 7.5 60/ 46WS-3454G 3 (76.2) 5-1/2 (139.7) 1-1/2 (38.1) 10/ 8.4 50/ 42WS-3484G 5-3/4 (146.0) 8-1/2 (215.9) 4-1/2 (114.3) 10/ 12.5 30/ 38

Meets ASTM A153 Class specifications for hot-dipped galvanizing > 45um = .002". It is highly recommended fordamp, humid environments near coastal regions. Hot-dipped galvanized Trubolts have a coating thickness of zinc that is almost 10 times as thick as electroplating. This creates greater corrosion resistance at a minimal cost.

SELECTION CHART

SELECTION CHART

Tie Wire Wedge for hanging suspended ceiling


Trubolt Type 316 Stainless Steel

Contains more nickel and chromium than Type 304, and 2%-3% molybdenum, which gives it better corrosion resistance. It is especially more effective in chloride environments that tend to cause pitting.



In. (mm)

SWW-1422 1-1/4 (31.8) 1/4" - 20 2-1/4 (57.2) 7/8 (22.2) 100/ 3.7 1000/ 37SWW-1432 2-1/4 (57.2) 3-1/4 (82.6) 1-1/8 (28.6) 100/ 4.8 1000/ 39SWW-3822 1-1/8 (28.6) 3/8" - 16 2-1/4 (57.2) 3/8 (9.5) 50/ 4.1 500/ 41SWW-3826 1-5/8 (41.3) 2-3/4 (69.9) 7/8 (22.2) 50/ 4.8 400/ 39SWW-3830 1-3/4 (44.5) 3 (76.2) 1-1/8 (28.6) 50/ 5.2 400/ 42SWW-3836 2-1/2 (63.5) 3-3/4 (95.5) 1-7/8 (47.6) 50/ 6.0 300/ 37SWW-3850 3-3/4 (95.3) 5 (127.0) 3-1/8 (79.4) 50/ 7.5 250/ 39SWW-1226 1-1/4 (31.8) 1/2" - 13 2-3/4 (69.9) 1/8 (3.2) 25/ 4.7 200/ 39SWW-1236 2-1/4 (57.2) 3-3/4 (95.3) 1 (25.4) 25/ 5.8 150/ 36SWW-1242 2-3/4 (69.9) 4-1/4 (108.0) 1-1/2 (38.1) 25/ 6.5 150/ 40SWW-1254 3 (76.2) 5-1/2 (139.7) 2-3/4 (69.9) 25/ 7.8 150/ 48SWW-5842 2-1/2 (63.5) 5/8" - 11 4-1/4 (108.0) 7/8 (22.2) 10/ 4.2 100/ 43SWW-5850 3-1/4 (82.6) 5 (127.0) 1-5/8 (41.3) 10/ 4.8 100/ 49SWW-5870 5-1/4 (133.4) 7 (177.8) 3-5/8 (92.1) 10/ 6.7 30/ 21SWW-3446 2-1/4 (57.2) 3/4" - 10 4-3/4 (120.7) 3/4 (19.1) 10/ 6.8 60/ 41SWW-3454 3 (76.2) 5-1/2 (139.7) 1-1/2 (38.1) 10/ 8.1 50/ 41

Typical Applications—Pumps, Diffusers, Gates, Weir Plates, etc.

Environment—Industrial (moderate to heavy atmospheric pollution)

Level of Corrosion—Medium to High

Trubolt Type 304Stainless Steel



In. (mm)

WW-1416 3/4 (19.1) 1/4" - 20 1-3/4 (44.5) 3/8 (9.5) 100/ 3.2 1000/ 32WW-1422 1-1/4 (31.8) 2-1/4 (57.2) 7/8 (22.2) 100/ 3.7 1000/ 37WW-1432 2-1/4 (57.2) 3-1/4 (82.6) 1-7/8 (47.6) 100/ 4.8 800/ 39WW-3822 1-1/8 (28.6) 3/8" - 16 2-1/4 (57.2) 3/8 (9.5) 50/ 4.1 500/ 41WW-3826 1-5/8 (41.3) 2-3/4 (69.9) 7/8 (22.2) 50/ 4.8 400/ 39WW-3830 1-3/4 (44.5) 3 (76.2) 1-1/8 (28.6) 50/ 5.1 400/ 42WW-3836 2-1/2 (63.5) 3-3/4 (95.3) 1-7/8 (47.6) 50/ 6.0 300/ 37WW-3850 3-3/4 (95.3) 5 (127.0) 3-1/8 (79.4) 50/ 7.5 250/ 39WW-1226 1-1/4 (31.8) 1/2" - 13 2-3/4 (69.9) 1/8 (3.2) 25/ 4.7 200/ 38WW-1236 2-1/4 (57.2) 3-3/4 (95.3) 1 (25.4) 25/ 5.8 150/ 36WW-1242 2-3/4 (69.9) 4-1/4 (108.0) 1-1/2 (38.1) 25/ 6.3 150/ 39WW-1254 3 (76.2) 5-1/2 (139.7) 2-3/4 (69.9) 25/ 7.7 150/ 47WW-1270 3-1/2 (88.9) 7 (177.8) 4-1/4 (108.0) 25/ 9.4 150/ 57WW-5834 1-3/4 (44.5) 5/8" - 11 3-1/2 (88.9) 1/8 (3.2) 10/ 3.6 100/ 37WW-5842 2-1/2 (63.5) 4-1/4 (108.0) 7/8 (22.2) 10/ 4.2 100/ 43WW-5850 3-1/4 (82.6) 5 (127.0) 1-5/8 (41.3) 10/ 4.8 100/ 49WW-5860 4-1/4 (107.9) 6 (152.4) 2-5/8 (66.7) 10/ 5.5 50/ 28WW-5870 5-1/2 (139.7) 7 (177.8) 3-5/8 (92.1) 10/ 6.2 30/ 20WW-5884 3-1/2 (88.9) 8-1/2 (215.9) 5-1/8 (130.2) 10/ 8.0 30/ 25WW-3442 1-3/4 (44.5) 3/4" - 10 4-1/4 (108.0) 1/4 (1.6) 10/ 6.8 60/ 42WW-3446 2-1/4 (57.2) 4-3/4 (120.7) 3/4 (19.1) 10/ 6.7 60/ 41WW-3454 3 (76.2) 5-1/2 (139.7) 1-1/2 (38.1) 10/ 7.5 50/ 38WW-3470 4 (101.6) 7 (177.8) 3 (76.2) 10/ 9.2 30/ 28WW-3484 5-3/4 (146.0) 8-1/2 (215.9) 4-1/2 (114.3) 10/ 12.3 30/ 38WW-34100 1-3/4 (44.5) 10 (254.0) 6 (152.4) 10/ 13.5 30/ 42WW-10060 2-1/2 (63.5) 1" - 8 6 (152.4) 1/2 (12.7) 5/ 8.3 25/ 43WW-10090 2-1/2 (63.5) 9 (228.6) 3-1/2 (88.9) 5/ 11.4 15/ 35WW-100120 2-1/2 (63.5) 12 (304.8) 6-1/2 (165.1) 5/ 15.0 15/ 46

Typical Applications—Cladding, Stadium Seating, etc.

Environment—Urban (slight to moderate degree of pollution)

Level of Corrosion—Medium

Serves many applications well. It withstands rusting in architectural and food processing environmentsand resists organic chemicals, dye stuffs and many inorganic chemicals.

Typical Applications—Tunnels, Dams, Tiles, Lighting Fixtures, etc.

Environment—Marine (heavy atmosphericpollution)

Level of Corrosion—High

SELECTION CHART

SELECTION CHART


ANCHOR INSTALLATION EMBEDMENT ANCHOR f’c = 2000 PSI (13.8 MPa) f’c = 4000 PSI (27.6 MPa) f’c = 6000 PSI (41.4 MPa)

DIA. TORQUE DEPTH TYPE TENSION SHEAR TENSION SHEAR TENSION SHEARIn. (mm) Ft. Lbs. (Nm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

1/4 (6.4) 8 (10.8) 1-1/8 (28.6) 1,180 (5.2) 1,400 (6.2) 1,780 (7.9) 1,400 (6.2) 1,900 (8.5) 1,400 (6.2)1-15/16 (49.2) 2,100 (9.3) 1,680 (7.5) 3,300 (14.7) 1,680 (7.5) 3,300 (14.7) 1,680 (7.5)2-1/8 (54.0) 2,260 (10.1) 1,680 (7.5) 3,300 (14.7) 1,680 (7.5) 3,300 (14.7) 1,680 (7.5)

3/8 (9.5) 25 (33.9) 1-1/2 (38.1) 1,680 (7.5) 2,320 (10.3) 2,240 (10.0) 2,620 (11.7) 2,840 (12.6) 3,160 (14.1)3 (76.2) 3,480 (15.5) 4,000 (17.8) 5,940 (26.4) 4,140 (18.4) 6,120 (27.2) 4,500 (20.0)4 (101.6) 4,800 (21.4) 4,000 (17.8) 5,940 (26.4) 4,140 (18.4) 6,120 (27.2) 4,500 (20.0)

1/2 (12.7) 55 (74.6) 2-1/4 (57.2) 4,660 (20.7) 4,760 (21.2) 5,100 (22.7) 4,760 (21.2) 7,040 (31.3) 7,040 (31.3)4-1/8 (104.8) 4,660 (20.7) 7,240 (32.2) 9,640 (42.9) 7,240 (32.2) 10,820 (48.1) 8,160 (36.3)6 (152.4) 5,340 (23.8) 7,240 (32.2) 9,640 (42.9) 7,240 (32.2) 10,820 (48.1) 8,160 (36.3)

5/8 (15.9) 90 (122.0) 2-3/4 (69.9) 6,580 (29.3) 7,120 (31.7) 7,180 (31.9) 7,120 (31.7) 9,720 (43.2) 9,616 (42.8)5-1/8 (130.2) 6,580 (29.3) 9,600 (42.7) 14,920 (66.4) 11,900 (52.9) 16,380 (72.9) 12,520 (55.7)7-1/2 (190.5) 7,060 (31.4) 9,600 (42.7) 15,020 (66.8) 11,900 (52.9) 16,380 (72.9) 12,520 (55.7)

3/4 (19.1) 175 (237.3) 3-1/4 (82.6) 7,120 (31.7) 10,120 (45.0) 10,840 (48.2) 13,720 (61.0) 13,300 (59.2) 15,980 (71.1)6-5/8 (168.3) 10,980 (48.8) 20,320 (90.4) 17,700 (78.7) 23,740 (105.6) 20,260 (90.1) 23,740 (105.6)

10 (254.0) 10,980 (48.8) 20,320 (90.4) 17,880 (79.5) 23,740 (105.6) 23,580 (104.9) 23,740 (105.6)

7/8 (22.2) 250 (339.0) 3-3/4 (95.3) 9,520 (42.3) 13,160 (58.5) 14,740 (65.6) 16,580 (73.8) 17,420 (77.5) 19,160 (85.2)6-1/4 (158.8) 14,660 (65.2) 20,880 (92.9) 20,940 (93.1) 28,800 (128.1) 24,360 (108.4) 28,800 (128.1)8 (203.2) 14,660 (65.2) 20,880 (92.9) 20,940 (93.1) 28,800 (128.1) 24,360 (108.4) 28,800 (128.1)

1 (25.4) 300 (406.7) 4-1/2 (114.3) 13,940 (62.0) 16,080 (71.5) 20,180 (89.8) 22,820 (101.5) 21,180 (94.2) 24,480 (108.9)7-3/8 (187.3) 14,600 (64.9) 28,680 (127.6) 23,980 (106.7) 37,940 (168.8) 33,260 (148.0) 38,080 (169.4)9-1/2 (241.3) 18,700 (83.2) 28,680 (127.6) 26,540 (118.1) 37,940 (168.8) 33,260 (148.0) 38,080 (169.4)

1-1/4 (31.8) 500 (677.9) 5-1/2 (139.7) 18,140 (80.7) 23,280 (103.6) 26,380 (117.3) 29,460 (131.0) 33,640 (149.6) 33,780 (150.3)8 (203.2) 27,340 (121.6) 35,080 (156.0) 43,300 (192.6) 44,260 (196.9) 45,540 (202.6) 50,560 (224.9)

* Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values.

Ultimate Tension and Shear Values (Lbs/kN) in Concrete*

Ultimate Tension and Shear Values (Lbs/kN) inLightweight Concrete*

ANCHOR INSTALLATION EMBEDMENT ANCHOR LIGHTWEIGHT CONCRETE LOWER FLUTE OF STEEL DECK WITH

DIA. TORQUE DEPTH TYPE f’c = 3000 PSI (20.7 MPa) LIGHTWEIGHT CONCRETE FILL

In. (mm) Ft. Lbs. (Nm) In. (mm) f’c = 3000 PSI (20.7 MPa)

TENSION SHEAR TENSION SHEARLbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

3/8 (9.5) 25 (33.9) 1-1/2 (38.1) 2,120 (9.4) 3,720 (16.5) 1,900 (8.5) 3,160 (14.1)3 (76.2) 2,940 (13.1) 4,240 (18.9) 2,840 (12.6) 4,000 (17.8)

1/2 (12.7) 55 (74.6) 2-1/4 (57.2) 3,600 (16.0) 7,040 (31.3) 3,400 (15.1) 5,380 (23.9)3 (76.2) 4,720 (21.0) 6,620 (29.4) 4,480 (19.9) 6,620 (29.4)4 (101.6) --- --- 6,920 (30.8) 4,800 (21.4) 6,440 (28.6)

5/8 (15.9) 90 (122.0) 3 (76.2) 6,000 (26.7) 9,240 (41.1) 4,720 (21.0) 5,500 (24.5)5 (127.0) 5,960 (26.5) 9,280 (41.3) 6,580 (29.3) 9,140 (40.7)

3/4 (19.1) 175 (237.3) 3-1/4 (82.6) 7,160 (31.9) 12,600 (56.0) 5,840 (26.0) 8,880 (39.5)5-1/4 (133.4) 8,900 (39.6) 15,920 (70.8) 7,040 (31.3) --- ---


WS-Carbon orWS-G

Hot-DippedGalvanized

orWW-304 S.S.

or SWW-316 S.S.

WS-Carbon orWS-G


orWW-304 S.S.

or SWW-316 S.S.



PERFORMANCE TABLE

PERFORMANCE TABLE


Recommended Spacing and Edge Distance Requirementsfor Tension Loads*

ANCHOR EMBEDMENT ANCHOR EDGE DISTANCE MIN. ALLOWABLE SPACING REQUIRED MIN. ALLOWABLEDIA. DEPTH TYPE REQUIRED TO EDGE DISTANCE AT TO OBTAIN MAX. SPACING AT WHICH

In. (mm) In. (mm) OBTAIN MAX. WHICH THE LOAD WORKING LOAD THE LOAD FACTORWORKING LOAD FACTOR APPLIED = .65 In. (mm) APPLIED = .70

In. (mm) In. (mm) In. (mm)

1/4 (6.4) 1-1/8 (28.6) 2 (50.8) 1 (25.4) 3-15/16 (100.0) 2 (50.8)1-15/16 (49.2) 1-15/16 (49.2) 1 (25.4) 3-7/8 (98.4) 1-15/16 (49.2)2-1/8 (54.0) 1-5/8 (41.3) 13/16 (20.6) 3-3/16 (81.0) 1-5/8 (41.3)

3/8 (9.5) 1-1/2 (38.1) 2-5/8 (66.7) 1-5/16 (33.3) 5-1/4 (133.4) 2-5/8 (66.7)3 (76.2) 3 (76.2) 1-1/2 (38.1) 6 (152.4) 3 (76.2)4 (101.6) 3 (76.2) 1-1/2 (38.1) 6 (152.4) 3 (76.2)

1/2 (12.7) 2-1/4 (57.2) 3-15/16 (100.0) 2 (50.8) 7-7/8 (200.0) 3-15/16 (100.0)4-1/8 (104.8) 3-1/8 (79.4) 1-9/16 (39.7) 6-3/16 (157.2) 3-1/8 (79.4)6 (152.4) 4-1/2 (114.3) 2-1/4 (57.2) 9 (228.6) 4-1/2 (114.3)

5/8 (15.9) 2-3/4 (69.9) 4-13/16 (122.2) 2-7/16 (61.9) 9-5/8 (244.5) 4-13/16 (122.2)5-1/8 (130.2) 3-7/8 (98.4) 1-15/16 (49.2) 7-1/16 (195.3) 3-7/8 (98.4)7-1/2 (190.5) 5-5/8 (142.9) 2-13/16 (71.4) 11-1/4 (285.8) 5-5/8 (142.9)

3/4 (19.1) 3-1/4 (82.6) 5-11/16 (144.5) 2-7/8 (73.0) 11-3/8 (288.9) 5-11/16 (144.5)6-5/8 (168.3) 5 (127.0) 2-1/2 (63.5) 9-15/16 (252.4) 5 (127.0)

10 (254.0) 7-1/2 (190.5) 3-3/4 (95.3) 15 (381.0) 7-1/2 (190.5)7/8 (22.2) 3-3/4 (95.3) 6-9/16 (166.7) 3-5/16 (84.1) 13-1/8 (333.4) 6-9/16 (166.7)

6-1/4 (158.8) 6-1/4 (158.8) 3-1/8 (79.4) 12-1/2 (317.5) 6-1/4 (158.8)8 (203.2) 6 (152.4) 3 (76.2) 12 (304.8) 6 (152.4)

1 (25.4) 4-1/2 (114.3) 7-7/8 (200.0) 3-15/16 (100.0) 15-3/4 (400.1) 7-7/8 (200.0)7-3/8 (187.3) 7-3/8 (187.3) 3-11/16 (93.7) 14-3/4 (374.7) 7-3/8 (187.3)9-1/2 (241.3) 7-1/8 (181.0) 3-9/16 (90.5) 14-1/4 (362.0) 7-1/8 (181.0)

1-1/4 (31.8) 5-1/2 (139.7) 9-5/8 (244.5) 4-13/16 (122.2) 19-1/4 (489.0) 9-5/8 (244.5)8 (203.2) 8 (203.2) 4 (101.6) 16 (406.4) 8 (203.2)

* Spacing and edge distances shall be divided by 0.75 when anchors are placed in structural lightweight concrete. Linear interpolation may be used for intermediate spacing and edge distances.

ANCHOR EMBEDMENT ANCHOR EDGE DISTANCE MIN. EDGE MIN. EDGE DISTANCE SPACING MIN. ALLOWABLEDIA. DEPTH TYPE REQUIRED TO DISTANCE AT WHICH AT WHICH THE REQUIRED TO SPACING BETWEEN

In. (mm) In. (mm) OBTAIN MAX. THE LOAD FACTOR LOAD FACTOR OBTAIN MAX. ANCHORS In. (mm) WORKING LOAD APPLIED = .60 APPLIED = .20 WORKING LOAD LOAD FACTOR

In. (mm) In. (mm) In. (mm) In. (mm) APPLIED = .40

1/4 (6.4) 1-1/8 (28.6) 2 (50.8) 1-5/16 (33.3) --- --- 3-15/16 (100.0) 2 (50.8)1-15/16 (49.2) 1-15/16 (49.2) 1 (25.4) --- --- 3-7/8 (98.4) 1-15/16 (49.2)

3/8 (9.5) 1-1/2 (38.1) 2-5/8 (66.7) 1-3/4 (44.5) --- --- 5-1/4 (133.4) 2-5/8 (66.7)3 (76.2) 3-3/4 (95.3) 3 (76.2) 1-1/2 (38.1) 6 (152.4) 3 (76.2)

1/2 (12.7) 2-1/4 (57.2) 3-15/16 (100.0) 2-9/16 (65.1) --- --- 7-7/8 (200.0) 3-15/16 (100.0)4-1/8 (104.8) 5-3/16 (131.8) 3-1/8 (79.4) 1-9/16 (39.7) 6-3/16 (157.2) 3-1/8 (79.4)

5/8 (15.9) 2-3/4 (69.9) 4-13/16 (122.2) 3-1/8 (79.4) --- --- 9-5/8 (244.5) 4-13/16 (122.2)5-1/8 (130.2) 6-7/16 (163.5) 3-7/8 (98.4) 1-15/16 (49.2) 7-11/16 (195.3) 3-7/8 (98.4)

3/4 (19.1) 3-1/4 (82.6) 5-11/16 (144.5) 3-3/4 (95.3) --- --- 11-3/8 (288.9) 5-11/16 (144.5)6-5/8 (168.3) 6-5/16 (160.3) 5 (127.0) 2-1/2 (63.5) 9-15/16 (252.4) 5 (127.0)

7/8 (22.2) 3-3/4 (95.3) 6-9/16 (166.7) 4-5/16 (109.5) --- --- 13-1/8 (333.4) 6-9/16 (166.7)6-1/4 (158.8) 8-1/2 (215.9) 6-1/4 (158.8) 3-1/8 (79.4) 12-1/2 (317.5) 6-1/4 (158.8)

1 (25.4) 4-1/4 (108.0) 7-7/8 (200.0) 5-1/8 (130.2) --- --- 15-3/4 (400.1) 7-7/8 (200.0)7-3/8 (187.3) 10-1/16 (255.6) 7-3/8 (187.3) 3-11/16 (93.7) 14-3/4 (374.7) 7-3/8 (187.3)

1-1/4 (31.8) 5-1/2 (139.7) 9-5/8 (244.5) 6-1/4 (158.8) --- --- 19-1/4 (489.0) 9-5/8 (244.5)8 (203.2) 11-7/16 (290.5) 8 (203.2) 4 (101.6) 16 (406.4) 8 (203.2)


Combined Shear and Tension Loading—for Trubolt AnchorsAllowable loads for anchors subjected to combined shear and tension forces are determined by the following equation:

(Ps /Pt ) 5/3 + (Vs /Vt ) 5/3 ≤ 1

Ps = Applied tension load Vs = Applied shear load Pt = Allowable tension load Vt = Allowable shear load

WS-Carbon or

WS-GHot-DippedGalvanized

orWW-304 S.S.

or SWW-316 S.S.

WS-Carbon orWS-G


orWW-304 S.S.

or SWW-316 S.S.



Recommended Spacing and Edge Distance Requirementsfor Shear Loads*

PERFORMANCE TABLE

PERFORMANCE TABLE


Uses standard drill bits—

no special drill bits to

purchase or lose!

SAVE TIMEEASILY INSTALLED■ Installs in less than half the time of 1/2" wedge

or adhesive application■ Simply drill a pilot hole and drive the LDT anchor by

hand or impact

EASILY REMOVED■ No torching or grinding required to remove anchors

SAVE MONEYLOWER DRILL BIT COSTS■ Use standard ANSI bits instead of proprietary bits■ Single piece design, no nut and washer to assemble

USE STANDARD ANSI BITS■ No special proprietary bits to purchase or lose■ Reduce chances for anchor failure due to incorrect

bit usage

Finished head,Removable Anchor


Self-threading Anchors — SPECIFIED FOR ANCHORAGE INTO CONCRETE

The LDT anchor is a high performance concrete anchor that cuts its ownthreads into concrete.

Anchor bodies are made of hardened carbon steel, plated with zinc orGRD2000® (tested to ASTM B117A for corrosion resistance).

The anchors shall have a finished hex washer head with anti-rotation serrations to prevent anchor back-out. The head of the anchor is stamped with a length identification code for easy inspection.

The anchor shall be installed with carbide tipped hammer drill bits made in accordance to ANSI B212.15-1994.

LDT Self-threadingAnchor

LargeDiameter

Tapcon (LDT ™) Anchors

LDT(3/8" and 1/2")

NOW AVAILABLE IN STAINLESS STEEL

The Easy, Fast, High Performing, RemovableTapcon, Now Available in 3/8" and 1/2" Diameter

5/8" DRILL BIT9/16" DRILL BITDRILL BIT SIZE REQUIRED

7"

HOLE DEPTH REQUIRED

1/2" LDT 5/8" wedge1/2" adhesive

7/16" DRILL BIT

4-1/2" 4-1/2"

LDT anchors specify asmaller & less expensivedrill bit than thoserequired with the 1/2"adhesive threaded rod orthe 5/8" wedge.

DIFFICULT TO REMOVE

EXPOSED THREADS

5-STEP INSTALLATION

CURE TIME

INSTALLS IN 1/2 THE TIME

EASILY REMOVED

FINISHED HEAD

PERMANENT APPLICATION

EXPOSED THREADS

DIFFICULT TO REMOVE

At 4-1/2" embedmentthe LDT anchor will giveyou performance similarto 1/2" adhesive anchorof the same depth or5/8" wedge anchors at 7" deep.

For use in concrete andconcrete block

ADVANTAGES


INSTALLATION STEPS

LDT Anchors

APPLICATIONS

FEATURES

Racking, shelving and conveyors are justa few high volume applications ideal forLarge Diameter Tapcon (LDT™). The easeand speed of installation of the LDT canreduce installation time to less than halfthe time of typical systems used today.

For installation speed, high performanceand easy removability, LDT is the anchorof choice.

APPROVALS/LISTINGS

ICBO Evaluation Service, Inc. – #ER-5890 City of Los Angeles – #RR25498

Easy InstallationInstalls into concrete by hand or impact wrench

Anti-rotation Serrated Washer— Prevents anchor back-out

Extra Large Hex Washer Head— With increased bearing surface — 3/8" LDT replaces 1/2" wedge

anchor application

Length Identification Head Stamp— For embedment inspection after

installation

Hi-Lo Threads— Cuts its own threads into concrete for

greater pull-out resistance

1. Using a 5/16" (for 3/8" LDT) or 7/16" (for 1/2"LDT) carbide tipped bit, drill a pilot hole at least1" deeper than anchor embedment.

2. Using a socket wrench (hand install) or electricimpact wrench, insert anchor into hole and tightenanchor until fully seated. (9/16" socket for 3/8" and3/4" socket for 1/2")

��

��

2. Installation Steps for BlockUsing a socket wrench insert anchor into hole and hand tighten anchor until fully seated.(9/16" socket for 3/8" and 3/4" socket for 1/2")

1. Using a 5/16" (for 3/8" LDT) or 7/16" (for 1/2"LDT) carbide tipped bit, drill a pilot hole at least1" deeper than anchor embedment.

��

Installation Steps in Concrete

Installation Steps in Concrete Block (CMU)

Installation by impact wrench—is recommendedfor faster installations or for high volume projects.Installation with impact wrench—is notrecommended for hollow block.

Installation by hand—is easy, simply using asocket wrench

LDT’s can be installed by hand or with animpact wrench

The LDT’s finished head and lack of exposedthreads virtually eliminates tire damage onfork lift trucks.


PART PART ANCHOR DRILL BIT EFFECTIVE MAX. THICKNESS QTY/WT QTY/WTNUMBER NUMBER DIA. DIA. LENGTH OF MATERIAL PER BOX PER MASTERFOR 410 FOR CARBON In. (mm) In. (mm) In. (mm) TO BE FASTENED lbs. CARTON

STAINLESS STEEL STEEL (see detail on left) In. (mm) lbs.

SLDT-3816 LDT-3816 3/8 (9.5) 5/16 (7.9) 1-3/4 (44.5) 1/4 (6.4) 50/ 3.0 400/ 24.0

SLDT-3824 LDT-3824 3/8 (9.5) 5/16 (7.9) 2-1/2 (63.5) 1 (25.4) 50/ 4.5 400/ 34.0

SLDT-3830 LDT-3830 3/8 (9.5) 5/16 (7.9) 3 (76.2) 1-1/2 (38.1) 50/ 5.0 400/ 40.0

SLDT-3840 LDT-3840 3/8 (9.5) 5/16 (7.9) 4 (101.6) 2-1/2 (63.5) 50/ 6.5 400/ 52.0

SLDT-1230 LDT-1230 1/2 (12.7) 7/16 (11.1) 3 (76.2) 1/2 (12.7) 25/ 4.5 150/ 27.0

SLDT-1240 LDT-1240 1/2 (12.7) 7/16 (11.1) 4 (101.6) 1-1/2 (38.1) 25/ 6.0 150/ 36.6

SLDT-1250 LDT-1250 1/2 (12.7) 7/16 (11.1) 5 (127.0) 2-1/2 (63.5) 25/ 7.6 150/ 45.6

* The stainless steel LDT‘s will be gold in color in order to differentiate them from the carbon steel anchors which are silver.

LDT Carbon andStainless Steel

with Zinc Plating

Meets ASTM B695 specifications for zinc plating of 5um = .0002" thickness. This material iswell suited for non-corrosive environments. For greater corrosion resistance GRD2000™ coating is available as special order.

SELECTION CHART

PART DESCRIPTION USABLE OVERALL QTY/WTNUMBER DRILLING LENGTH LENGTH PER BOX

DD-5164 5/16" SDS Plus 4" 6" 1/.15

DD-7164 7/16" SDS Plus 4" 6" 1/.15

DD-71610 7/16" SDS Plus 10" 12" 1/.15

DD-124 1/2" SDS Plus 4" 6" 1/.15

DD-1210 1/2" SDS Plus 10" 12" 1/.7

DD-1216 1/2" SDS Plus 16" 18" 1/.7

DD-5164K Bulk Pack DD-5164 4" 6" 25/3.1

* Straight shank and spline shank of the appropriate size can also be used.

LDT AnchorAccessories

ACCESSORIES

SDS Carbide Bits*—stronger shaft and core than industry standard for longer bit life

LENGTH INDICATION CODE*

CODE LENGTH OF ANCHOR In. (mm)

A 1-1/2 < 2 (38.1 < 50.8)

B 2 < 2-1/2 (50.8 < 63.5)

C 2-1/2 < 3 (63.5 < 76.2)

D 3 < 3-1/2 (76.2 < 88.9)

E 3-1/4 < 4 (88.9 < 101.6)

F 4 < 4-1/2 (101.6 < 114.3)

G 4-1/2 < 5 (114.3 < 127.0)

H 5 < 5-1/2 (127.0 < 139.7)*Located on top of anchor for easy inspection.

LENGTH INDICATION CODE*

HOLE DIAMETER THROUGH FIXTURE SUGGESTED LDT DIAMETERIn. (mm) In. (mm)

7/16 (11.1) 3/8 (9.5)

1/2 (12.7) 3/8 (9.5)

9/16 (14.3) 1/2 (12.7)

5/8 (15.9) 1/2 (12.7)

DESIGN GUIDE

EffectiveLength

For proper selection of anchor diameters based upon predrilledholes through base plates and fixtures to be fastened.


Allowable Tension and Shear Values* (Lbs/kN) in ConcreteCarbon and Stainless Steel1

ANCHOR EMBEDMENT f’c = 2000 PSI (13.8 MPa) f’c = 3000 PSI (20.7 MPa) f’c = 4000 PSI (27.6 MPa)

DIA. DEPTH TENSION SHEAR TENSION SHEAR TENSION SHEARIn. (mm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

3/8 (9.5) 1-1/2 (38.1) 334 (1.5) 527 (2.3) 413 (1.8) 691 (3.1) 492 (2.1) 854 (3.8)

2 (50.8) 373 (1.7) 759 (3.4) 506 (2.2) 807 (3.6) 638 (2.8) 855 (3.8)

2-1/2 (63.5) 933 (4.2) 828 (3.7) 937 (4.2) 841 (3.7) 940 (4.2) 856 (3.8)

3-1/2 (88.9) 1,349 (6.0) 828 (3.7) 1,656 (7.4) 842 (3.7) 1,963 (8.7) 857 (3.8)

1/2 (12.7) 2 (50.8) 895 (4.0) 1,411 (6.3) 977 (4.3) 1,628 (7.2) 1,059 (4.7) 1,845 (8.2)

3-1/2 (88.9) 1,813 (8.0) 1,609 (7.2) 2,011 (8.9) 1,822 (8.1) 2,209 (9.8) 2,035 (9.0)

4-1/2 (114.3) 2,544 (11.3) 1,846 (8.2) 2,583 (11.5) 1,992 (8.9) 2,622 (11.7) 2,138 (9.5)

* Allowable values are based upon a 4 to 1 safety factor. (Ultimate/4)

LDT Anchors

Recommended Edge & Spacing Requirements for Tension Loads*Carbon and Stainless Steel

ANCHOR DIA. EMBEDMENT DEPTH EDGE DISTANCE LOAD FACTOR APPLIED SPACING DISTANCE LOAD FACTOR APPLIEDIn. (mm) In. (mm) REQUIRED TO OBTAIN AT MIN. EDGE DISTANCE REQUIRED TO OBTAIN AT MIN. SPACING

MAX. WORKING LOAD 1-3/4 Inches (44mm) MAX. WORKING LOAD DISTANCE In. (mm) In. (mm) 3 Inches (76mm)

3/8 (9.5) 1-1/2 (38.1) 2 (50.8) 70% 6 (152.4) 44%

2 (50.8) 2 (50.8) 70% 6 (152.4) 44%

2-1/2 (63.5) 3 (76.2) 70% 6 (152.4) 44%

3-1/2 (88.9) 4 (101.6) 70% 6 (152.4) 44%

1/2 (12.7) 2 (50.8) 2-1/4 (57.2) 65% 8 (203.2) 27%

3-1/2 (88.9) 3 (76.2) 65% 8 (203.2) 27%

4-1/2 (114.3) 4 (101.6) 65% 8 (203.2) 27%

* Edge and spacing distance shall be divided by .75 when anchors are placed in structural lightweight concrete. Linear interpolation may be used for intermediate spacing and edge distances.

LDT Anchors

PERFORMANCE TABLE

PERFORMANCE TABLE

Recommended Edge & Spacing Requirements for Shear Loads*Carbon and Stainless Steel

ANCHOR DIA. EMBEDMENT DEPTH EDGE DISTANCE LOAD FACTOR APPLIED SPACING DISTANCE LOAD FACTOR APPLIEDIn. (mm) In. (mm) REQUIRED TO OBTAIN AT MIN. EDGE DISTANCE REQUIRED TO OBTAIN AT MIN. SPACING

MAX. WORKING LOAD 1-3/4 Inches (44mm) MAX. WORKING LOAD DISTANCE In. (mm) In. (mm) 3 Inches (76mm)

3/8 (9.5) 1-1/2 (38.1) 3 (76.2) 25% 6 (152.4) 57%

2 (50.8) 4 (101.6) 25% 6 (152.4) 57%

2-1/2 (63.5) 5 (127.0) 25% 6 (152.4) 57%

3-1/2 (88.9) 5 (127.0) 25% 6 (152.4) 57%

1/2 (12.7) 2 (50.8) 5 (127.0) 25% 8 (203.2) 60%

3-1/2 (88.9) 5 (127.0) 25% 8 (203.2) 60%

4-1/2 (114.3) 5-1/2 (139.7) 25% 8 (203.2) 60%

* Edge and spacing distances shall be divided by .75 when anchors are placed in structural lightweight concrete. Linear interpolation may be used for intermediate spacing and edge distances.

LDT Anchors

PERFORMANCE TABLE


Allowable Tension and Shear* (Lbs/kN) in Concrete Block (anchors should be installed by hand in hollow block)

ANCHOR DIA. EMBEDMENT HOLLOW CONCRETE BLOCK GROUT FILLED CONCRETE BLOCK In. (mm) DEPTH

In. (mm) TENSION SHEAR TENSION SHEARLbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

3/8 (9.5) 1-1/2 (38.1) 229 (1.0) 794 (3.5) 398 (1.8) 975 (4.3)

1/2 (12.7) 2-1/2 (63.5) ---- ---- ---- ---- 1,481 (6.6) 1,670 (7.4)

* Allowable values are based upon a 4 to 1 safety factor. (Ultimate/4)

LDT Anchors

LDT Installed inLower Flute

20 Gauge Metal Deck

Upper FluteAnchoring Overhead in 3000 PSI LightweightConcrete On Metal DeckLDT Anchors

PERFORMANCE TABLE

PERFORMANCE TABLE

ANCHOR DRILL HOLE EMBEDMENT 3000PSI (20.7 MPa) CONCRETEDIAMETER In. (mm) ULTIMATE TENSION LOAD ALLOWABLE WORKING LOADIn. (mm) Lbs. (kN) Lbs. (kN)

3/8” LDT 5/16 (7.9) 1-1/2 (38.1) Upper Flute 2,889 (12.9) 722 (3.2)

Lower Flute 1,862 (8.3) 465 (2.1)


Multi-Set IIDrop-In Anchors

ADVANTAGES

■ Lipped anchor body keeps anchor flush


■ Keeps all rods same length

■ Easy inspection

■ Available in carbon steel, 18-8 and 316 stainless steel

InternallyThreaded Heavy-

Duty AnchoringSystems


Drop-In, Shell-Type Anchors— SPECIFIED FOR ANCHORAGE INTO CONCRETE

Drop-In, shell-type anchors feature an internally threaded, all-steel shell with expansion cone insert and flushembedment lip. Anchors are manufactured from plated carbon steel, 18-8 stainless steel and 316 stainless steel.

Anchors should be installed with carbide tipped hammer drill bits made in accordance to ANSI B212.15-1994 specifications.

Anchors should be tested to ASTM E488 criteria and listed by ICBO and SBCCI. Anchors should also be listed by the following agencies as required by the local building code: UL, FM, City of Los Angeles, Metro-Dade County,California State Fire Marshal and Cal Trans.Multi-Set II Drop-In Anchors

RM Drop-In Anchor

■ Below surface setting for easy patch work

■ Higher performance potential with deep embedment setting

RL Drop-In Anchor

■ Optimized (only 3/4" long) for use in hollow-core, pre-cast plank and post-tension slabs

■ Lip keeps anchor flush during installation

■ Shallow drilling—fast installation

RX-38 Drop-In Anchor

■ Quick thread attachment—ideal for 1 sided forming

■ Use coil rod on job

■ 2 diameters (1/2" and 3/4")

formwork

existingconcrete

coil rod, holding form in place

bentrebar

Coil Thread Anchor

®


1. Drill hole the same diameter as outside diameterof anchor being used to any depth exceeding minimum embedment. Clean hole.

2. Drive anchor flush with surface of concrete.

3. Expand anchor with setting tool provided.

Anchor is properly expanded when shoulder

of setting tool is flush with top of anchor.

To set anchor below surface:

Drill hole deeper than anchor length. Thread bolt into anchor. Hammer anchor into hole until bolt head is at desired depth. Remove bolt and set anchor with setting tool.

To set anchor flush with surface:

INSTALLATION STEPS

Multi-Set II Anchors

APPLICATIONS

FEATURES

Pumps and heavy piping are commonapplications for larger diameter Multi-Set Drop-In Anchors.

Cable tray and strut suspended fromconcrete ceilings are ideal Multi-Setapplications. In post-tension or hollow-core slabs use the RX-38.

The Multi-Set Anchor is the standardfor pipe-hanging. The RM version has aretainer lip to keep all anchors flush atthe surface, keeping all your threadedrod the same length.

APPROVALS/LISTINGSMeets or exceeds U.S. Government G.S.A. Specification FF-S-325 Group VIII, Type 1

Underwriters Laboratories

Factory Mutual

ICBO Evaluation Service, Inc. – #ER-1372




Cal Trans

Expander Slots—allow for easy settingand superior performance

Cone Insert—that expands the anchorwhen driven with setting tool and hammer

Body—available in zinc-plated steel, 18-8 stainless steel, and 316 stainless steel

Easy Depth Inspection—keeps threadedrod drop lengths consistent

Retainer Lip—to keep anchor flush with surface

(See page 75 for part numbers.)

PART NUMBER RT-138

1 setting tool per master carton—except for RX-38 which is 1 per box.

PART NUMBER RTX-138

For use with RX-38 only.

For use with threaded rods or headedbolts (supplied by contractor)


USER APPLICATION BASE CORROSION DROP-IN PART SETTING BOLT SIZE- DRILL BIT THREAD EMBEDMENT QTY/WT QTY/WTTYPE MATERIAL RESISTANCE ANCHOR NUMBER TOOL THREADS SIZE DEPTH MIN. HOLE PER BOX PER

LEVEL TYPE PART PER INCH In. (mm) In. (mm) DEPTH lbs. MASTER CTN NUMBER* In. (mm) lbs.

HVAC/Fire Sprinkler Poured Low RM RM-14 RT-114 1/4" - 20 3/8 (9.5) 3/8 (9.5) 1 (25.4) 100/ 2.6 1000/ 28

Plumber (Pipe-fitter) in place RM-38 RT-138 3/8" - 16 1/2 (12.7) 1/2 (12.7) 1 - 5/8 (41.3) 50/ 3.4 500/ 36

concrete/ RM-12 RT-112 1/2" - 13 5/8 (15.9) 3/4 (19.1) 2 (50.8) 50/ 5.8 400/ 49

lightweight RM-58 RT-158 5/8" - 11 7/8 (22.2) 1 (25.4) 2 - 1/2 (63.5) 25/ 7.8 125/ 41

fill deck RM-34 RT-134 3/4" - 10 1 (25.4) 1-1/4 (31.8) 3-3/16 (81.0) 25/ 11.9 100/ 49

Hollow-core Low RX RX-38 RTX-138 3/8" - 16 1/2 (12.7) 1/2 (12.7) 3/4 (19.1) 100/ 3.5 1000/ 36

pre-cast

or Post-

tension

Solid Medium SRM SRM-14 RT-114 1/4" - 20 3/8 (9.5) 3/8 (9.5) 1 (25.4) 100/ 2.7 1000/ 28

concrete 18-8 S.S. SRM-38 RT-138 3/8" - 16 1/2 (12.7) 1/2 (12.7) 1 - 5/8 (41.3) 50/ 3.4 500/ 36

SRM-12 RT-112 1/2" - 13 5/8 (15.9) 3/4 (19.1) 2 (50.8) 50/ 6.0 400/ 50

SRM-58 RT-158 5/8" - 11 7/8 (22.2) 1 (25.4) 2 - 1/2 (63.5) 25/ 18.0 125/ 42

SRM-34 RT-134 3/4" - 10 1 (25.4) 1-1/4 (31.8) 3-3/16 (81.0) 25/ 12.0 100/ 50

Solid High SSRM SSRM-38 RT-138 3/8" - 16 1/2 (12.7) 1/2 (12.7) 1 - 5/8 (41.3) 50/ 3.4 500/ 36

concrete 316 S.S. SSRM-12 RT-112 1/2" - 13 5/8 (15.9) 3/4 (19.1) 2 (50.8) 50/ 6.0 400/ 50

Concrete Contractor, Solid Low CL-Coil CL-12 RT-112 1/2" - 6 5/8 (15.9) 3/4 (19.1) 2 (50.8) 50/ 5.7 400/ 47

General Contractor, Highway concrete Threaded CL-34 RT-134 3/4" - 4.5 1 (25.4) 1-1/4 (31.8) 3-3/16 (81.0) 25/ 11.9 100/ 49

Concrete Cutting/ Solid Low RL RL-14 RT-114 1/4" - 20 3/8 (9.5) 3/8 (9.5) 1 (25.4) 100/ 2.6 1000/ 28

Sawing Contractor/Misc. Metal concrete (w/o lip) RL-38 RT-138 3/8" - 16 1/2 (12.7) 1/2 (12.7) 1 - 5/8 (41.3) 50/ 3.4 500/ 36

RL-12 RT-112 1/2" - 13 5/8 (15.9) 3/4 (19.1) 2 (50.8) 50/ 5.8 400/ 49

RL-58 RT-158 5/8" - 11 7/8 (22.2) 1 (25.4) 2 - 1/2 (63.5) 25/ 7.8 125/ 41

RL-34 RT-134 3/4" - 10 1 (25.4) 1-1/4 (31.8) 3-3/16 (81.0) 25/ 11.9 100/ 49


SELECTION CHART

* 1 setting tool per master carton—except for RX-38 which is 1 per box.


BOLT ANCHOR MIN. EMBEDMENT ANCHOR TENSION Lbs. (kN) SHEAR Lbs. (kN)DIA. DIA. DEPTH TYPE f’c = 2000 PSI f’c = 4000 PSI f’c = 6000 PSI f’c >_2000 PSI

In. (mm) In. (mm) In. (mm) (13.8 MPa) (27.6 MPa) (41.4 MPa) (13.8 MPa)

1/4 (6.4) 3/8 (9.5) 1 (25.4) 1,680 (7.5) 2,360 (10.5) 2,980 (13.3) 1,080 (4.8)

3/8 (9.5) 1/2 (12.7) 1-5/8 (41.3) 2,980 (13.3) 3,800 (16.9) 6,240 (27.8) 3,160 (14.1)

1/2 (12.7) 5/8 (15.9) 2 (50.8) 3,300 (14.7) 5,840 (26.0) 8,300 (36.9) 4,580 (20.4)

5/8 (15.9) 7/8 (22.2) 2-1/2 (63.5) 5,500 (24.5) 8,640 (38.4) 11,020 (49.0) 7,440 (33.1)

3/4 (19.1) 1 (25.4) 3-3/16 (81.0) 8,280 (36.8) 9,480 (42.2) 12,260 (54.5) 10,480 (46.6)


Ultimate Shear and Tension Values (Lbs/kN) in Concrete*

RM, RL or CL-Carbon

or SRM-18-8 S.S. or

SSRM-316 S.S.


Ultimate Shear and Tension Values (Lbs/kN) inLightweight Concrete*

BOLT ANCHOR MINIMUM ANCHOR LIGHTWEIGHT CONCRETE LOWER FLUTE OF STEEL DECK WITHDIA. DIA. EMBEDMENT TYPE f’c = 3000 PSI (20.7 MPa) LIGHTWEIGHT CONCRETE FILL

In. (mm) In. (mm) DEPTH f’c = 3000 PSI (20.7 MPa)In. (mm) TENSION SHEAR TENSION SHEAR

Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

3/8 (9.5) 1/2 (12.7) 1-5/8 (39.7) 3,860 (17.2) 4,420 (19.6) 3,340 (14.9) 4,420 (19.6)

1/2 (12.7) 5/8 (15.9) 2 (50.8) 4,080 (18.1) 5,640 (25.1) 3,200 (14.2) 4,940 (22.0)

5/8 (15.9) 7/8 (22.2) 2-1/2 (63.5) 6,280 (27.9) 10,440 (46.4) 5,960 (26.5) 5,840 (26.0)

3/4 (19.1) 1 (25.4) 3-3/16 (81.0) 11,000 (48.9) 15,780 (70.2) 8,180 (36.4) 9,120 (40.6)


RM, RLor CL-Carbon or

SRM-18-8 S.S. or SSRM-316 S.S.


Combined Shear and Tension Loading—for Multi-Set AnchorsAllowable loads for anchors subjected to combined shear and tension forces are determined by the following equation:

(Ps /Pt ) 5/3 + (Vs /Vt ) 5/3 ≤ 1


PERFORMANCE TABLE

PERFORMANCE TABLE


BOLT ANCHOR EMBEDMENT ANCHOR EDGE DISTANCE MIN. EDGE SPACING MIN. ALLOWABLEDIA. DIA. DEPTH TYPE REQUIRED TO DISTANCE AT WHICH REQUIRED TO SPACING

In. (mm) In. (mm) In. (mm) OBTAIN MAX. LOAD FACTOR APPLIED OBTAIN MAX. BETWEEN ANCHORSWORKING LOAD =.80 FOR TENSION WORKING LOAD LOAD FACTOR APPLIED

In. (mm) =.70 FOR SHEAR In. (mm) =.80 FOR TENSIONIn. (mm) =.55 FOR SHEAR

In. (mm)

1/4 (6.4) 3/8 (9.5) 1 (25.4) 1-3/4 (44.5) 7/8 (22.2) 3-1/2 (88.9) 1-3/4 (44.5)

3/8 (9.5) 1/2 (12.7) 1-5/8 (41.3) 2-7/8 (73.0) 1-7/16 (36.5) 5-11/16 (144.5) 2-7/8 (73.0)

1/2 (12.7) 5/8 (15.9) 2 (50.8) 3-1/2 (88.9) 1-3/4 (44.5) 7 (177.8) 3-1/2 (88.9)

5/8 (15.9) 7/8 (22.2) 2-1/2 (63.5) 4-3/8 (111.1) 2-3/16 (55.6) 8-3/4 (222.3) 4-3/8 (111.1)

3/4 (19.1) 1 (25.4) 3-3/16 (81.0) 5-5/8 (142.9) 2-13/16 (71.4) 11-3/16 (284.2) 5-5/8 (142.9)


RM, RL or CL-Carbon

or SRM-18-8 S.S. or

SSRM-316 S.S.

Multi-Set IIDrop-In Anchors Recommended Spacing and Edge Distance Requirements*

PERFORMANCE TABLE

PERFORMANCE TABLE

SIZE ANCHOR EMBEDMENT 4000PSI (27.6 MPa) CONCRETE HOLLOW COREIn. (mm) DIA. In. (mm) TENSION SHEAR TENSION SHEAR

In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

3/8 (9.5) 1/2 (12.7) 3/4 (19.1) 1,987 (8.8) 2,903 (12.9) 1,908 (8.5) 2,525 (11.2)

* The tabulated values are for RX-38 anchors installed at a minimum of 12 diameters on center and minimum edge distance of 6 diameters for 100 percent anchor efficiency. Spacing and edge distance may be reduced to 6 diameters spacing and 3 diameter edge

distance provided the values are reduced 50 percent. Linear Interpolation may be used for intermediate spacings and edge margins.


Ultimate Shear and Tension Values (Lbs/kN) for RX-38(3/4" Embedment)*


PERFORMANCE TABLE

RX Drop-InInstalled inUpper Flute

Lower Flute

20 Gauge Metal Deck


RX-38 Drop-In 1/2 (12.7) 3/4 (19.1) Upper Flute 1,410 (6.3) 353 (1.6)

Lower Flute 1,206 (5.4) 301 (1.3)


Anchoring Overhead in 3000 PSI Lightweight Concrete On Metal Deck



DynaboltGold

Sleeve Anchors

ADVANTAGES

■ Carbon steel anchors feature a Grade 5 bolt formaximum strength.

■ Carbon Steel anchors feature a special organicclear coat that achieves 250 hours, neutral saltspray test.

■ Stainless Steel anchors available in 316 SS as astandard product.

■ Finished head anchors, bolt can be easilyremoved.

Unique Design ofHeavy Duty,

Finished HeadAnchor, Clamps

Down Base Plates

Dynabolt Gold Heavy-DutySleeve Anchor

The Dynabolt Gold anchor is a heavy duty sleeve anchor that can be used toanchor fixtures to concrete, concrete block, or brick. The anchor consists of ahex head bolt, a spacer sleeve, specially designed expansion sleeve, and anexpansion cone. Carbon steel anchors feature a Grade 5 hex head bolt anda special organic clear coat over zinc plating for added corrosion protection(250 hours, neutral salt spray, ASTM B117). Stainless steel anchors areavailable in Type 316 Stainless Steel.


Heavy-Duty Sleeve Type Anchors — SPECIFIED FOR ANCHORAGE INTO CONCRETE, MASONRY, GROUT-FILLED BLOCK ANDHOLLOW BLOCK

Dynabolt Gold(Carbon Steel)

Dynabolt Gold (316 Stainless Steel)

The chart shows how much eachanchor shortens or “pulls down”when the anchors are torqued.The vertical axis is the distancein inches.

0.3

0.25

0.2

0.15

0.1

0.05

03/8" 1/2" 5/8" 3/4"

Anchor Diameter

Pull D

own D

istan

ce

Upon tightening, the Dynabolt Gold pulls down and shortens in length.This dynamic action creates tremendous holding power while at thesame time pulling down uneven base plates.

The unique design of Dynabolt Gold—it twists, shortens and pulls down.


1. Use a bit with a diameter equal to the anchor.See selection chart to determine proper sizebit for anchor used. Drill hole to any depthexceeding minimum embedment. Clean hole.

2. Insert assembled anchor into hole, so thatwasher or head is flush with materials to be fastened.

INSTALLATION STEPS

3. Expand anchor by tightening nut or head2 to 3 turns.

Dynabolt Gold Anchors

APPLICATIONS

FEATURES

Dynabolt Gold is ideal for attachinglumber to concrete, concrete block,or brick.

Dynabolt Gold offers excellent holdingstrength for attaching steel ledgers.

The Dynabolt Gold has a finished head and tremendous performance in grouted block or solid concrete for a clean, safe stair rail installation.

APPROVALS/LISTINGS

Meets or exceeds U.S. Government G.S.A. Specification FF-S-325 Group II,Type 3, Class 1

Other approvals pending

Finished Head Bolt, Easy to remove

Grade 5 Bolt – Carbon steel anchors

AISI 316 – Stainless steel anchors

Special slotted expansion sleeve – twistsand shortens to provide maximumclamping force when anchor is torqued

Threaded expansion cone for maximumexpansion force inside the sleeve


PERFORMANCE TABLE

ANCHOR INSTALLATION EDGE DISTANCE MIN. ALLOWABLE SPACING REQUIRED MIN. ALLOWABLE DIA. TORQUE REQUIRED TO OBTAIN EDGE DISTANCE AT TO OBTAIN MAX. SPACING BETWEEN ANCHORS

In. (mm) Ft. Lbs. (Nm) MAX. WORKING LOAD WHICH THE LOAD FACTOR WORKING LOAD LOAD FACTORIn. (mm) APPLIED = 0.75 In. (mm) APPLIED = 0.50

In. (mm) In. (mm)

3/8 (9.5) 35 (47.5) 3-3/4 (95.3) 1-7/8 (47.6) 4-1/2 (114.3) 1-7/8 (47.6)1/2 (12.7) 60 (81.4) 5 (127.0) 2-1/2 (63.5) 6 (152.4) 2-1/2 (63.5)5/8 (15.9) 100 (135.7) 6-1/4 (158.8) 3-1/8 (79.4) 7-1/2 (190.5) 3-1/8 (79.4)3/4 (19.1) 120 (162.8) 7-1/2 (190.5) 3-3/4 (95.3) 9 (228.6) 3-3/4 (95.3)

Linear interpolation may be used for intermediate spacing and edge distances.

Recommended Spacing and Edge Distance Requirements for Tension Loads

Dynabolt GoldSleeve Anchors

Dynabolt Gold Carbon Steel with Zinc Plating

PART ANCHOR ANCHOR INSTALLATION QTY/WT QTY/WTNUMBER DRILL LENGTH TORQUE PER BOX PER MASTER

DIAMETER In. (mm) Ft. Lbs. (Nm) lbs. CARTON In. (mm) lbs.

HB-3820 DG 3/8 (9.5) 2 (50.8) 35 (47.5) 50/3.8 250/19

HB-3830 DG 3/8 (9.5) 3 (76.2) 35 (47.5) 50/5.1 250/26

HB-1236 DG 1/2 (12.7) 3-3/4 (95.3) 60 (81.4) 25/5.6 125/28

HB-1246 DG 1/2 (12.7) 4-3/4 (120.7) 60 (81.4) 25/7.0 125/35

HB-1256 DG 1/2 (12.7) 5-3/4 (146.5) 60 (81.4) 25/8.0 125/40

HB-5842 DG 5/8 (15.9) 4 (101.6) 100 (135.7) 10/4.1 50/20

HB-5850 DG 5/8 (15.9) 5 (127.0) 100 (135.7) 10/5.3 50/26

HB-5860 DG 5/8 (15.9) 6 (152.4) 100 (135.7) 10/6.1 50/28

HB-3442 DG 3/4 (19.1) 4-1/4 (108.0) 150 (203.5) 5/3.3 25/16

HB-3452 DG 3/4 (19.1) 5-1/4 (133.4) 150 (203.5) 5/3.9 25/19

HB-3472 DG 3/4 (19.1) 7-1/4 (184.2) 150 (203.5) 5/4.6 25/23

SHB-3820 DG 3/8 (9.5) 2 (50.8) 35 (47.5) 50/3.8 250/19

SHB-3830 DG 3/8 (9.5) 3 (76.2) 35 (47.5) 50/5.1 250/26

SHB-1236 DG 1/2 (12.7) 3-3/4 (95.2) 60 (81.4) 25/5.6 125/28

SHB-1246 DG 1/2 (12.7) 4-3/4 (120.7) 60 (81.4) 25/7.0 125/35

SELECTION CHART

Carb

on St

eel

316 S

S

expansion cone

hex head bolt

spacer sleeve

specially designedexpansion sleeve


PERFORMANCE TABLE

PERFORMANCE TABLE

ANCHOR INSTALLATION EDGE DISTANCE MIN. ALLOWABLE SPACING REQUIRED MIN. ALLOWABLE DIA. TORQUE REQUIRED TO OBTAIN EDGE DISTANCE AT TO OBTAIN MAX. SPACING BETWEEN ANCHORS

In. (mm) Ft. Lbs. (Nm) MAX. WORKING LOAD WHICH THE LOAD FACTOR WORKING LOAD LOAD FACTORIn. (mm) APPLIED = 0.50 In. (mm) APPLIED = 0.50

In. (mm) In. (mm)

3/8 (9.5) 35 (47.5) 4-1/2 (114.3) 1-7/8 (47.6) 4-1/2 (114.3) 1-7/8 (47.6)1/2 (12.7) 60 (81.4) 6 (152.4) 2-1/2 (63.5) 6 (152.4) 2-1/2 (63.5)5/8 (15.9) 100 (135.7) 7-1/2 (190.5) 3-1/8 (79.4) 7-1/2 (190.5) 3-1/8 (79.4)3/4 (19.1) 120 (162.8) 9 (228.6) 3-3/4 (95.3) 9 (228.6) 3-3/4 (95.3)

Linear interpolation may be used for intermediate spacing and edge distances.

Recommended Spacing and Edge Distance Requirements for Shear Loads


ANCHOR DIA. EMBEDMENT 3000 PSI (20.7 MPa) 4000 PSI (27.6 MPa) 6000 PSI (41.4 MPa) 4000 PSI (27.6 MPa) In. (mm) In. (mm) TENSION TENSION TENSION SHEAR

Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

3/8 (9.5) 1-1/2 (38.1) 1,481 (6.6) 1,814 (8.1) 2,094 (9.3) 5,737 (25.5)

2-1/8 (54.0) 3,510 (15.6) 4,299 (19.1) 4,965 (22.1) 6,861 (30.5)

1/2 (12.7) 1-5/8 (41.3) 2,452 (10.9) 3,342 (14.9) 3,859 (17.2) -- --

2-3/8 (60.3) 5,161 (23.0) 6,321 (28.1) 7,299 (32.5) 9,525 (42.4)

2-3/4 (69.8) 6,719 (29.9) 8,229 (36.6) 9,502 (42.3) 9,525 (42.4)

5/8 (15.9) 1-7/8 (47.6) 3,098 (13.8) 3,794 (16.9) 4,381 (19.5) -- --

2-3/4 (69.8) 6,237 (27.7) 7,639 (34.0) 8,821 (39.2) 13,661 (60.8)

3-1/2 (88.9) 9,664 (43.0) 11,836 (52.7) 13,667 (60.8) 13,661 (60.8)

3/4 (19.1) 2-3/8 (60.3) 4,721 (21.0) 5,782 (25.7) 6,676 (29.7) -- --

3-3/8 (85.7) 8,761 (39.0) 10,730 (47.7) 12,390 (55.1) 15,445 (68.7)

4-1/8 (104.8) 12,744 (56.7) 15,608 (69.4) 18,023 (80.2) 15,445 (68.7)

Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values.

Average Ultimate Shear and Tension Values (Lbs/kN) forCarbon Steel in Concrete


ANCHOR INSTALLATION BOLT MINIMUM ANCHOR LIGHTWEIGHT MEDIUM WEIGHTDIA. TORQUE DIA. EMBEDMENT TYPE HOLLOW CORE GROUT FILLED HOLLOW CORE GROUT FILLED

In. (mm) Ft. Lbs. In. (mm) DEPTH In. (mm) (STEEL) TENSION SHEAR TENSION SHEAR TENSION SHEAR TENSION SHEAR(Nm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

3/8 (9.5) 15 (20.3) 5/16 (7.9) 1-1/2 (38.1) Carbon 1,360 (6.0) 2,560 (11.4) 1,360 (6.0) 2,560 (11.4) 1,360 (6.0) 2,560 (11.4) 1,360 (6.0) 2,560 (11.4)Stainless 1,160 (5.2) 2,560 (11.4) 1,160 (5.2) 2,560 (11.4) 1,160 (5.2) 2,560 (11.4) 1,160 (5.2) 2,560 (11.4)

1/2 (12.7) 25 (33.9) 3/8 (9.5) 1-7/8 (47.6) Carbon -- -- -- -- 2,220 (9.9) 4,000 (17.8) -- -- -- -- 2,220 (9.9) 4,000 (17.8)Stainless -- -- -- -- 2,100 (9.3) 4,000 (17.8) -- -- -- -- 2,100 (9.3) 4,000 (17.8)

5/8 (15.9) 55 (74.6) 1/2 (12.7) 2 (50.8) Carbon -- -- -- -- 3,080 (13.7) 6,440 (28.6) -- -- -- -- 3,080 (13.7) 6,440 (28.6)

3/4 (19.1) 90 (122.0) 5/8 (15.9) 2-1/2 (63.5) Carbon -- -- -- -- 4,200 (18.7) 10,200 (45.4) -- -- -- -- 4,200 (18.7) 10,200 (45.4)

* Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values. The tabulated values are for anchors installed in a minimum of 12 diameters on center and a minimum edge distance of 6 diameters for 100 percent anchor efficiency. Spacing and edge distance may be reduced to 6 diameter spacing and 3 diameter edge distance, provided the values are reduced 50 percent. Linear interpolation may be used for intermediate spacings and edge distances.

Ultimate Shear and Tension Values in Masonry Units (Lbs/kN)*

PERFORMANCE TABLE



DynaboltSleeve

Anchors

ADVANTAGES

■ Anchor diameter equals hole diameter

■ Available in hex head and six other head styles

■ Available 1/4 - 3/4" diameter up to 6-1/4" length

■ Zinc plated carbon steel and 304 stainless steel

■ Provides full 360° hole contact over large areaand reduces concrete stress

■ Heavy-loading capacity

■ Preassembled for faster, easier installations

■ Dynabolt can be installed through object to be fastened

■ Sleeve design improves holding power

■ No pre-spotting of holes necessary

Versatile,Medium-DutySleeve Anchor

Available Head Styles

Sleeve type anchors feature a split expansion sleeve over a threaded studbolt body and integral expander, nut and washer.

Anchors are made of Plated Carbon Steel, or Type 18-8 Stainless Steel.

Anchors should be installed with carbide tipped hammer drill bits made inaccordance to ANSI B212.15-1994.

Anchors are tested to ASTM E488 criteria.


Sleeve Type Anchors— SPECIFIED FOR ANCHORAGE INTO CONCRETE, MASONRY, GROUT-FILLED BLOCK ANDHOLLOW BLOCK

Phillips Flat Head Hex Nut Acorn Nut(FS) (HN) (AN)

Tie Wire Round Head Threshold Flat Head(TW) (RS) (TH)

DynaboltMasonrySleeve Anchor

Full range of head style, corrosion protection, and sizes makes theDynabolt Sleeve the right product for almost any application.

Dynabolt Hex Nut Sleeve Anchor

®


1. Use a bit with a diameter equal to the anchor.See selection chart to determine proper sizebit for anchor used. Drill hole to any depthexceeding minimum embedment. Clean hole.

2. Insert assembled anchor into hole, so thatwasher or head is flush with materials to be fastened.

INSTALLATION STEPS

3. Expand anchor by tightening nut or head2 to 3 turns.

Dynabolt Anchors

APPLICATIONS

FEATURES

Electrical junction boxes are commonapplications for the Dynabolt Sleeveanchor because it works well in solidconcrete, concrete block, and brick. It is also available in several finishedhead styles.

The Dynabolt Sleeve anchor works well in hollow materials like brick andblock. It is available in zinc-plated carbon steel and 304 stainless steel.

Door and window frames are commonlyattached to the structure with DynaboltSleeve anchors because of their finishedand threshold head styles and performance in block and brick.

APPROVALS/LISTINGS

Meets or exceeds U.S. Government G.S.A. Specification FF-S-325 Group II,Type 3, Class 3

Factory Mutual



Multiple Head Styles—for any application

Range of Fixture Thickness—no weakened shear area because of all-steel spacer sleeve (no plastic)

Sleeve Design—for better holding

360° Hole Contact—gives better pullout resistance


DynaboltCarbon Steel with Zinc Plating

PART ANCHOR EFFECTIVE BOLT MIN. MAX. QTY/WT QTY/WTNUMBER DIA. & ANCHOR DIA./ EMBEDMENT THICKNESS PER BOX PER

DRILL LENGTH* THREADS In. (mm) OF MATERIAL lbs. MASTERBIT SIZE In. (mm) PER INCH TO BE FASTENED CARTON

In. (mm) lbs.

AN-1405 1/4" 5/8 (15.9) 3/16" /24 1/2 (12.7) 1/8 (3.2) 100/ 1.9 1000/ 20AN-1413 1-3/8 (34.9) 3/16" /24 1-1/8 (28.6) 1/4 (6.4) 100/ 2.6 1000/ 27AN-1422 2-1/4 (57.2) 3/16" /24 1-1/8 (28.6) 1-1/8 (28.6) 100/ 3.7 1000/ 38HN-1405 1/4" 5/8 (15.9) 3/16" /24 1/2 (12.7) 1/8 (3.2) 100/ 1.6 1000/ 17HN-1413 1-3/8 (34.9) 3/16" /24 1-1/8 (28.6) 1/4 (6.4) 100/ 2.3 1000/ 24HN-1422 2-1/4 (57.2) 3/16" /24 1-1/8 (28.6) 1-1/8 (28.6) 100/ 3.4 1000/ 35HN-1614 5/16" 1-1/2 (38.1) 1/4" /20 1-1/4 (31.8) 1/4 (6.4) 100/ 4.0 1000/ 41HN-1624 2-1/2 (63.5) 1/4" /20 1-1/4 (31.8) 1-1/4 (31.8) 100/ 5.9 800/ 47HN-3817 3/8" 1-7/8 (47.6) 5/16" /18 1-1/2 (38.1) 3/8 (9.5) 50/ 3.5 500/ 36HN-3830 3 (76.2) 5/16" /18 1-1/2 (38.1) 1-1/2 (38.1) 50/ 4.9 400/ 40HN-1222 1/2" 2-1/4 (57.2) 3/8" /16 1-7/8 (47.6) 3/8 (9.5) 25/ 3.3 250/ 34HN-1230 3 (76.2) 3/8" /16 1-7/8 (47.6) 1-1/8 (28.6) 25/ 4.0 200/ 33HN-1240 4 (101.6) 3/8" /16 1-7/8 (47.6) 2-1/8 (54.0) 25/ 5.3 200/ 44HN-5822 5/8" 2-1/4 (57.2) 1/2" /13 2 (50.8) 1/4 (6.4) 25/ 6.3 150/ 38HN-5830 3 (76.2) 1/2" /13 2 (50.8) 1 (25.4) 25/ 7.0 150/ 46HN-5842 4-1/4 (108.0) 1/2" /13 2 (50.8) 2-1/4 (57.2) 10/ 3.9 100/ 41HN-5860 6 (152.4) 1/2" /13 2 (50.8) 4 (101.6) 10/ 4.9 50/ 25HN-3424 3/4" 2-1/2 (63.5) 5/8" /11 2-1/4 (57.2) 1/4 (6.4) 10/ 4.7 50/ 25HN-3440 4 (101.6) 5/8" /11 2-1/4 (57.2) 1-3/4 (44.5) 5/ 3.2 50/ 33HN-3462 6-1/4 (158.8) 5/8" /11 2-1/4 (57.2) 4 (101.6) 5/ 4.3 50/ 44FS-1411 1/4" 1-1/2 (38.1) 3/16" /24 1-1/8 (28.6) 3/8 (9.5) 100/ 1.9 1000/ 21FS-1420 (head dia. .477) 2-1/4 (57.2) 3/16" /24 1-1/8 (28.6) 1-1/8 (28.6) 100/ 2.7 1000/ 28FS-1430 3-1/8 (79.4) 3/16" /24 1-1/8 (28.6) 2 (50.8) 100/ 3.8 1000/ 38FS-1440 4 (101.6) 3/16" /24 1-1/8 (28.6) 2-7/8 (73.0) 100/ 4.7 1000/ 48FS-3826 3/8" 2-7/8 (73.0) 5/16" /18 1-1/2 (38.1) 1-3/8 (34.9) 50/ 3.8 500/ 40FS-3840 (head dia. .722) 4 (101.6) 5/16" /18 1-1/2 (38.1) 2-1/2 (63.5) 50/ 5.3 400/ 44FS-3850 5 (127.0) 5/16" /18 1-1/2 (38.1) 3-1/2 (88.9) 50/ 5.6 300/ 40FS-3860 6 (152.4) 5/16" /18 1-1/2 (38.1) 4-1/2 (114.3) 50/ 8.0 300/ 48TH-1420 1/4" 2-1/4 (57.2) 3/16" /24 1-1/8 (28.6) 1-1/8 (28.6) 100/ 2.5 1000/ 25

(head dia. .385)

RS-1411 1/4" 1-3/8 (34.9) 3/16" /24 1-1/8 (28.6) 1/4 (6.4) 100/ 1.9 1000/ 20RS-1420 2 (50.8) 3/16" /24 1-1/8 (28.6) 7/8 (22.2) 100/ 2.7 1000/ 28RS-1426 2-7/8 (73.0) 3/16" /24 1-1/8 (28.6) 1-3/4 (44.5) 100/ 3.7 1000/ 38RS-3824 3/8" 2-5/8 (66.7) 5/16" /18 1-1/2 (38.1) 1-1/8 (28.6) 50/ 3.9 500/ 41TW-1614 5/16" 1-1/2 (38.1) 1/4" /20 1-1/2 (38.1) 9/32 (7.1) 100/ 4.9 1000/ 50

hole* Phillips flat head uses a standard 80°– 82° counter sink.

Typical Applications—Shelf ledgers, electrical boxes,conduit

Environment—Interior(non-corrosive)

Level of Corrosion—Low

ACOR

N NU

THE

AD S

TYLE

THRE

SHOL

DFL

AT H

EAD

HEX

NUT

PHILL

IPS F

LAT H

EAD*

ROUN

D HE

ADTIE WIR

E

DynaboltType 304 Stainless Steel

PART ANCHOR EFFECTIVE BOLT MIN. MAX. QTY/WT QTY/WTNUMBER DIA. & ANCHOR DIA./ EMBEDMENT THICKNESS PER BOX PER

DRILL LENGTH* THREADS In. (mm) OF MATERIAL lbs. MASTERBIT SIZE In. (mm) PER INCH TO BE FASTENED CARTON

In. (mm) lbs.

SHN-1413 1/4" 1-3/8 (34.9) 3/16" /24 1-1/8 (28.6) 1/4 (6.4) 100/ 2.3 1000/ 24SHN-3817 3/8" 1-7/8 (47.6) 5/16" /18 1-1/2 (38.1) 3/8 (9.5) 50/ 3.5 500/ 36SHN-3830 3 (76.2) 5/16" /18 1-1/2 (38.1) 1-1/2 (38.1) 50/ 4.9 400/ 40SHN-1222 1/2" 2-1/4 (57.2) 3/8" /16 1-7/8 (47.6) 3/8 (9.5) 25/ 3.3 250/ 34SHN-1230 3 (76.2) 3/8" /16 1-7/8 (47.6) 1-1/8 (28.6) 25/ 4.0 200/ 33SHN-1240 4 (101.6) 3/8" /16 1-7/8 (47.6) 2-1/8 (54.0) 25/ 5.3 200/ 44SHN-5842 5/8" 4-1/4 (108.0) 1/2" /13 2 (50.8) 2-1/4 (57.2) 10/ 3.9 100/ 41SFS-1420 1/4" 2-1/4 (57.2) 3/16" /24 1-1/8 (28.6) 1-1/8 (28.6) 100/ 2.7 1000/ 28SFS-1430 3-1/8 (79.4) 3/16" /24 1-1/8 (28.6) 3 (76.2) 100/ 3.8 1000/ 38SFS-3826 3/8" 2-7/8 (73.0) 5/16" /18 1-1/2 (38.1) 1-3/8 (34.9) 50/ 3.8 500/ 40SFS-3840 4 (101.6) 5/16" /18 1-1/2 (38.1) 2-1/2 (63.5) 50/ 5.3 400/ 44SRS-1420 1/4" 2 (50.8) 3/16" /24 1-1/8 (28.6) 7/8 (22.2) 100/ 2.7 1000/ 28

* Flat head uses a standard 80°– 82° counter sink.

Typical Applications—Cladding and Brick Ties

Environment—Slight tomoderate degree of pollution

Level of Corrosion—Medium

HEX

NUT

HEAD

STY

LESL

OTTE

D FL

AT H

EAD*

ROUN

D HE

AD

SELECTION CHART

SELECTION CHART

* Effective Anchor Length

AA

A

(FS) (HN) (RS)


ANCHOR INSTALLATION BOLT MINIMUM ANCHOR f’c = 2000 PSI (13.8 MPa) f’c = 3000 PSI (20.7 MPa) f’c = 4000 PSI (27.6 MPa)DIA. TORQUE DIA. EMBEDMENT TYPE TENSION SHEAR TENSION SHEAR TENSION SHEAR

In. (mm) Ft. Lbs. (Nm) In. (mm) DEPTH In. (mm) (STEEL) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

1/4 (6.4) 3.5 (4.7) No.10 1-1/8 (28.6) 1,200 (5.3) 1,620 (7.2) 1,600 (7.1) 1,620 (7.2) 2,100 (9.3) 1,620 (7.2)

5/16 (7.9) 8 (10.8) 1/4 (6.4) 1-1/4 (31.8) 1,400 (6.2) 2,040 (9.1) 1,920 (8.5) 2,220 (9.9) 2,600 (11.6) 2,400 (10.7)

3/8 (9.5) 14 (19.0) 5/16 (7.9) 1-1/2 (38.1) 1,620 (7.2) 2,560 (11.4) 2,240 (10.0) 2,800 (12.5) 3,100 (13.8) 3,040 (13.5)

1/2 (12.7) 20 (27.1) 3/8 (9.5) 1-7/8 (47.6) 2,220 (9.9) 4,000 (17.8) 3,140 (14.0) 4,500 (20.0) 4,400 (19.6) 5,000 (22.2)

5/8 (15.9) 48 (65.1) 1/2 (12.7) 2 (50.8) 3,080 (13.7) 6,440 (28.6) 4,400 (19.6) 7,240 (32.2) 6,120 (27.2) 8,080 (35.9)

3/4 (19.1) 90 (122.0) 5/8 (15.9) 2-1/4 (57.2) 4,200 (18.7) 10,200 (45.4) 6,060 (27.0) 11,600 (51.6) 8,900 (39.6) 13,100 (58.3)

Ultimate Shear and Tension Values in Concrete (Lbs/kN)*

Carbon or Stainless

DynaboltSleeve Anchors

ANCHOR INSTALLATION BOLT MINIMUM ANCHOR f’c = 4000 PSI (27.6 MPa) f’c = 6000 PSI (41.4 MPa)DIA. TORQUE DIA. EMBEDMENT TYPE TENSION SHEAR TENSION SHEAR

In. (mm) Ft. Lbs. (Nm) In. (mm) DEPTH In. (mm) (STEEL) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

1/4 (6.4) 3.5 (4.7) No.10 1-1/8 (28.6) 1,080 (4.8) 1,160 (5.2) 1,220 (5.4) 1,940 (8.6)

5/16 (7.9) 8 (10.8) 1/4 (6.4) 1-1/4 (31.8) 1,260 (5.6) 1,680 (7.5) 1,440 (6.4) 2,220 (9.9)

3/8 (9.5) 14 (19.0) 5/16 (7.9) 1-1/2 (38.1) 1,620 (7.2) 2,300 (10.2) 2,240 (10.0) 2,800 (12.5)

1/2 (12.7) 25 (33.9) 3/8 (9.5) 1-7/8 (47.6) 2,600 (11.6) 3,920 (17.4) 3,160 (14.1) 4,840 (21.5)

5/8 (15.9) 48 (65.1) 1/2 (12.7) 2 (50.8) 3,240 (14.4) 5,600 (24.9) 4,300 (19.1) 7,840 (34.9)

3/4 (19.1) 90 (122.0) 5/8 (15.9) 2-1/4 (57.2) 3,640 (16.2) 8,640 (38.4) 5,800 (25.8) 12,480 (55.5)

Ultimate Shear and Tension Values in Lightweight Concrete (Lbs/kN)*

Carbon or

Stainless


ANCHOR INSTALLATION BOLT MINIMUM ANCHOR LIGHTWEIGHT MEDIUM WEIGHTDIA. TORQUE DIA. EMBEDMENT TYPE HOLLOW CORE GROUT FILLED HOLLOW CORE GROUT FILLED

In. (mm) Ft. Lbs. In. (mm) DEPTH In. (mm) (STEEL) TENSION SHEAR TENSION SHEAR TENSION SHEAR TENSION SHEAR(Nm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

1/4 (6.4) 3.5 (4.7) 3/16 (4.8) 1-1/8 (28.6) Carbon 1,120 (5.0) 1,360 (6.0) 1,120 (5.0) 1,360 (6.0) 1,120 (5.0) 1,620 (7.2) 1,120 (5.0) 1,360 (6.0)Stainless 640 (2.8) 1,620 (7.2) 640 (2.8) 1,620 (7.2) 640 (2.8) 1,620 (7.2) 640 (2.8) 1,620 (7.2)

3/8 (9.5) 15 (20.3) 5/16 (7.9) 1-1/2 (38.1) Carbon 1,360 (6.0) 2,560 (11.4) 1,360 (6.0) 2,560 (11.4) 1,360 (6.0) 2,560 (11.4) 1,360 (6.0) 2,560 (11.4)Stainless 1,160 (5.2) 2,560 (11.4) 1,160 (5.2) 2,560 (11.4) 1,160 (5.2) 2,560 (11.4) 1,160 (5.2) 2,560 (11.4)

1/2 (12.7) 25 (33.9) 3/8 (9.5) 1-7/8 (47.6) Carbon -- -- -- -- 2,220 (9.9) 4,000 (17.8) -- -- -- -- 2,220 (9.9) 4,000 (17.8)Stainless -- -- -- -- 2,100 (9.3) 4,000 (17.8) -- -- -- -- 2,100 (9.3) 4,000 (17.8)

5/8 (15.9) 55 (74.6) 1/2 (12.7) 2 (50.8) Carbon -- -- -- -- 3,080 (13.7) 6,440 (28.6) -- -- -- -- 3,080 (13.7) 6,440 (28.6)Stainless -- -- -- -- 3,080 (13.7) 6,440 (28.6) -- -- -- -- 2,820 (12.5) 6,440 (28.6)

3/4 (19.1) 90 (122.0) 5/8 (15.9) 2-1/2 (63.5) Carbon -- -- -- -- 4,200 (18.7) 10,200 (45.4) -- -- -- -- 4,200 (18.7) 10,200 (45.4)* Allowable values are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values. The tabulated values are for anchors installed in a minimum of 12 diameters on center and a minimum edge distance of 6 diameters for 100 percent

anchor efficiency. Spacing and edge distance may be reduced to 6 diameter spacing and 3 diameter edge distance, provided the values are reduced 50 percent. Linear interpolation may be used for intermediate spacings and edge distances.

Ultimate Shear and Tension Values in Masonry Units (Lbs/kN)*

PERFORMANCE TABLE

PERFORMANCE TABLE

PERFORMANCE TABLE


Combined Shear and Tension Loading—for Dynabolt AnchorsAllowable loads for anchors subjected to combined shear and tension forces are determined by the following equation: (Ps /Pt ) + (Vs /Vt ) ≤ 1



StudAnchors

ADVANTAGES

FEATURES

External Threads for easy equipment setting

Stamped part number on body

Pre-assembled expander plug—easy anchor to set—drill and hammer in—anchor is bottom bearing

■ Fast and easy to install

■ Same drill size as anchor size

■ Bottom-bearing design is ideal for jacking and leveling applications

■ Install anchor directly through fixture

■ Hammer-driven expansion design eliminates torque requirements, for dependable holding capacity

Bottom-Bearing,Hammer-Driven

Anchors


Stud Type Anchors — SPECIFIED FOR ANCHORAGE INTO CONCRETE

Stud Anchors feature a bolt body and pre-assembled expander plug.Anchors should be installed with carbide tipped hammer drill bits made in accordance to ANSI B212.15-1994.

Anchors are tested to ASTM E488 criteria and listed by SBCCI. Anchors are listed by the following agencies as required: UL and FM.

APPLICATIONS

Stud Anchors are commonly used to anchorequipment to concrete slabs. The externalstuds make for easy jacking and leveling for easy cleanup in industrial settings.

APPROVALS/LISTINGS

Meets or exceeds U.S. Government G.S.A. specification FF-S-325 Group VIII, Type 2

SBCCI Compliance Report – #9570 Factory Mutual

California State Fire Marshal Underwriters Laboratories

™

StudAnchor


PART HOLE OR BIT SIZE OVERALL STUD THREAD MIN. QTY/WT QTY/WTNUMBER (THREADS) LENGTH LENGTH LENGTH EMBEDMENT PER BOX PER MASTER

PER INCH In. (mm) In. (mm) In. (mm) In. (mm) lbs. CARTON lbs.

JS-14C 1/4" - 20 1-3/4 (44.5) 3/4 (19.1) 5/8 (15.9) 1-3/8 (34.9) 100/ 2.6 1000/ 26JS-14H 2-1/4 (57.2) 1-1/8 (28.6) 7/8 (22.2) 1-3/8 (34.9) 100/ 3.1 1000/ 31JS-14M 3-1/4 (82.6) 2-1/8 (54.0) 7/8 (22.2) 1-3/8 (34.9) 100/ 4.5 1000/ 45JS-38C 3/8" - 16 2-1/4 (57.2) 1 (25.4) 3/4 (19.1) 1-5/8 (41.3) 50/ 3.6 500/ 36JS-38H 3 (76.2) 1-5/8 (41.3) 1-1/4 (31.8) 1-5/8 (41.3) 50/ 4.5 500/ 45JS-38M 3-3/4 (95.3) 2-1/4 (57.2) 1-1/4 (31.8) 1-5/8 (41.3) 50/ 5.7 500/ 57JS-12C 1/2" - 13 2-3/4 (69.9) 1-1/8 (28.6) 7/8 (22.2) 1-7/8 (47.6) 25/ 3.9 250/ 39JS-12H 4-1/4 (108.0) 2-1/2 (63.5) 2 (50.8) 1-7/8 (47.6) 25/ 5.6 250/ 56JS-12M 5-1/4 (133.4) 3-5/8 (92.1) 2 (50.8) 1-7/8 (47.6) 25/ 7.0 250/ 70JS-58H 5/8" - 11 5 (127.0) 3 (76.2) 2-1/4 (57.2) 2-3/8 (60.3) 10/ 4.1 100/ 42JS-34H 3/4" - 10 6-1/4 (158.8) 3-3/4 (95.3) 2-1/2 (63.5) 2-7/8 (73.0) 10/ 7.6 50/ 59

1. Drill hole same diameteras anchor to embedmentspecified in chart. Clean hole.

2. Drive anchor with expanderplug in bottom, throughmaterial to be fastened.

I N S TA L L AT I O N S T E P S

3. Expand anchor by driving anchor over plug with hammer.

Stud Anchors

Stud Anchors

ANCHOR MINIMUM f ’c = 2000 PSI (13.8 MPa) f ’c = 4000 PSI (27.6 MPa)DIA. EMBEDMENT DEPTH TENSION SHEAR TENSION SHEAR

In. (mm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

1/4 (6.4) 1-3/8 (34.9) 1,120 (5.0) 580 (2.6) 1,500 (6.7) 1,640 (7.3)3/8 (9.5) 1-5/8 (41.3) 1,740 (7.7) 2,280 (10.1) 3,160 (14.1) 3,360 (14.9)1/2 (12.7) 1-7/8 (47.6) 2,680 (11.9) 5,320 (23.7) 4,020 (17.9) 5,100 (22.7)5/8 (15.9) 2-3/8 (60.3) 3,200 (14.2) 5,460 (24.3) 5,520 (24.6) 6,820 (30.3)3/4 (19.1) 2-7/8 (73.0) 4,020 (17.9) 8,100 (36.0) 7,520 (33.5) 8,560 (38.1)

Allowable loads are based upon a 4 to 1 safety factor. Divide by 4 for allowable load values.

Ultimate Shear and Tension Values in Concrete (Lbs/kN)Stud Anchors

ANCHOR MINIMUM EDGE DISTANCE MIN. EDGE DISTANCE SPACING MIN. ALLOWABLE SPACINGDIA. EMBEDMENT REQUIRED TO AT WHICH LOAD REQUIRED TO BETWEEN ANCHORS

In. (mm) DEPTH OBTAIN MAX. FACTOR APPLIED OBTAIN MAX. LOAD FACTOR APPLIEDIn. (mm) WORKING LOAD = .90 FOR TENSION WORKING LOAD = .90 FOR TENSION

In. (mm) = .65 FOR SHEAR In. (mm) = .50 FOR SHEARIn. (mm) In. (mm)

1/4 (6.4) 1-3/8 (34.9) 2-7/16 (61.9) 1-1/4 (31.8) 4-13/16 (122.2) 2-7/16 (61.9)3/8 (9.5) 1-5/8 (41.3) 2-7/8 (73.0) 1-7/16 (36.5) 5-11/16 (144.5) 2-7/8 (73.0)1/2 (12.7) 1-7/8 (47.6) 3-5/16 (84.1) 1-11/16 (42.9) 6-9/16 (166.7) 3-5/16 (84.1)5/8 (15.9) 2-3/8 (60.3) 4-3/16 (106.4) 2-1/8 (54.0) 8-5/16 (211.1) 4-3/16 (106.4)3/4 (19.1) 2-7/8 (73.0) 5-1/16 (128.6) 2-9/16 (65.1) 10-1/16 (255.6) 5-1/16 (128.6)

* Linear interpolation may be used for intermediate spacing and edge distances.

Stud Anchors Recommended Spacing and Edge Distance Requirements*

Combined Shear and Tension Loading—for Stud AnchorsAllowable loads for anchors subjected to combined shear and tension forces are determined by the following equation: (Ps /Pt ) 5/3 + (Vs /Vt ) 5/3 ≤ 1


SELECTION CHART

PERFORMANCE TABLE

PERFORMANCE TABLE

Note: Recommended thickness of concrete for bottom-bearing anchors = embedment depth+ three times anchor diameter

Redi-DriveAnchors

®

100% ContactMore contact—more holdingpower!

.215 Shank Diameter

.198

ADVANTAGES■ High performance provides superior holding

values in concrete and other masonry materials

■ Fire resistant

■ Tamper resistant

■ Standard 3/16" drill hole size—cheaper bitand faster installation

■ Available in 3/4", 1-1/8", 1-5/8", 2", 2-1/2", and3" lengths

■ Most economical steel anchor available

■ Provides fast, high performance drive-type fastening without torquing or need for special setting equipment

As simple as using a nail—drive into predrilled holes for tremendous holdingstrength in concrete. Compressive strength is created by forcing a larger

diameter fastener into a smaller size hole.The greater the degree of contact the greater the holding power.

Only 3 Points of ContactHalf the holding power of Redi-Drive

.190ShankDiameter

.260

Only 2 Points of ContactOne-fourth theholding powerof Redi-Drive

.250ShankDiameter

.260

The Redi-Drive is a high performance small diameter one-piece hammer-drive anchor. The anchor holds based on a friction principle—the shank diameter is larger than the drill hole size. Anchors shall be

installed with carbide-tipped hammer drill bits made in accordance to ANSI B212.15-1994.

The Redi-Drive is available in four types…mushroom head, pipe-hanging (1/4" & 3/8") FM approved (on 3/8"), Tie-Wire, and double-head forming versions. Anchor performance in solid concrete at one inch embedment shallexceed 400 lbs. allowable tension load and 750 lbs. allowable shear load.


Light-Duty Hammer-Drive Masonry Anchors—SPECIFIED FOR ANCHORAGE INTO CONCRETE, BLOCK AND BRICK

Redi-Drive HighPerformanceHammer-DriveAnchor


Redi-DriveAnchors—High

PerformanceWithout Torquing

TieWire

FinishedHead

PipeDrive

FormingAnchor


1. Drill a 3/16" diameter hole (1/4" for 3/8" pipedrive) at a minimum depth (see chart) andclean hole.

2. Insert anchor through material to be fastened(insert tie-wire or pipe version Redi-Drive Anchorsinto drilled holes) and drive anchor with a 3-lb.hammer until the head is flush with surface ordesired embedment.

��

��

��yy

��yyy

��y

��yyy

��yy

��yyy

INSTALLATION STEPS

3. Anchor is now set.

1. Drill 3/16" diameter hole in concrete.

2. Hammer in flat side of Redi-Drive 1-1/4".

��

��

��

INSTALLATION STEPS FOR REDI-TIE-DRIVE

3. The Redi-Drive is set. Tie acoustical or electricaldrop wire to open hole.

Redi-Drive Anchors

FEATURES

APPROVALS/LISTINGS

Meets or exceeds U.S. Government G.S.A. Specification FF-S-325 Group VI

Factory Mutual (3/8" pipe-drive)

Tamper-Proof—mushroom head

100% Hole Contact—.215 shank in .198 hole

Dog-Point—for easy insertion and installation

APPLICATIONS

Signage and other light duty metalproducts are common applications for the Redi-Drive. It has superior performance in block, brick and solidconcrete, and is tamper-proof.

Wood attachments to concrete arecommon Redi-Drive applications,whether permanent or temporary.

Electrical boxes and conduit clips that need permanent attachment areideal applications for the Redi-Drive.It works well in all base materialsand is fast and economical.


Typical Applications—Electrical boxes, conduitclips, and duct work

Redi-DriveAnchors

PART HEAD DIA. DRILL SIZE TOTAL MIN. MAX. FIXTURE CLEARANCE QTY/WT QTY/WT PERNUMBER In. (mm) In. (mm) LENGTH EMBEDMENT THICKNESS HOLE SIZE PER BX MASTER CARTON

In. (mm) In. (mm) In. (mm) In. (mm) lbs. lbs.

RD4-034 7/16 (11.1) 3/16 (4.8) 3/4 (19.1) 11/16 (17.5) 1/16 (1.6) 1/4 (6.4) 100/ 1.4 1000/ 15

RD4-118 7/16 (11.1) 3/16 (4.8) 1-1/8 (28.6) 3/4 (19.1) 3/8 (9.5) 1/4 (6.4) 100/ 1.6 1000/ 17

RD4-158 7/16 (11.1) 3/16 (4.8) 1-5/8 (41.3) 3/4 (19.1) 7/8 (22.2) 1/4 (6.4) 100/ 2.2 1000/ 23

RD4-200 7/16 (11.1) 3/16 (4.8) 2 (50.8) 3/4 (19.1) 1-1/4 (31.8) 1/4 (6.4) 100/ 2.6 1000/ 26

RD4-212 7/16 (11.1) 3/16 (4.8) 2-1/2 (63.5) 3/4 (19.1) 1-3/4 (44.5) 1/4 (6.4) 100/ 3.2 1000/ 33

RD4-300 7/16 (11.1) 3/16 (4.8) 3 (76.2) 3/4 (19.1) 2-1/4 (57.2) 1/4 (6.4) 100/ 3.7 1000/ 37

Pipe HangingTypicalApplications—Fire sprinkler, waterlines, steam/gas,cable tray, electricalconduits

FormingWood attachments toconcrete are commonRedi-Drive applications,whether permanent ortemporary

Tie Wire TypicalApplications—Acoustical ceilings,suspended electricalfixture, pencil rod

��Redi-DriveAnchors

PART HEAD SIZE DRILL SIZE TOTAL MIN. HEAD HEAD SIZE QTY/WT QTY/WTNUMBER O.D. In. (mm) LENGTH EMBEDMENT HEIGHT I.D. PER BX PER MASTER

In. (mm) In. (mm) In. (mm) In. (mm) lbs. CARTON lbs.

TD4-112 3/16 (4.8) 3/16 (4.8) 2-1/8 (54.0) 1-1/4 (31.8) 5/8 (15.9) 9/32" hole 100/ 3.5 1000/ 35

SELECTION CHART

SELECTION CHART

1. Drill 3/16" diameter hole for1/4" anchor (1/4" diameterhole for 3/8" anchor).

2. Hammer in anchor 1-1/4"for 1/4" anchor (1-3/4" for3/8" anchor).

��

��

��INSTALLATION STEPS FOR REDI-PIPE-DRIVE

3. The Redi-Drive is set. Run1/4" or 3/8" threaded rodor bolt into anchor.

PART INTERNAL DRILL SIZE TOTAL MIN. HEAD INTERNAL QTY/WT QTY/WTNUMBER THREAD SIZE In. (mm) LENGTH EMBEDMENT HEIGHT THREADED PER BX PER MASTER

I.D. In. (mm) In. (mm) In. (mm) DIAMETER O.D. lbs. CARTON In. (mm) lbs.

PD4-112 1/4 - 20" 3/16 (4.8) 2-1/8 (54.0) 1-1/4 (31.8) 5/8 (15.9) 13/32 (10.3) 100/ 3.0 1000/ 30

PD8-134 3/8 - 16" 1/4 (6.4) 2-1/2 (63.5) 1-3/4 (44.5) 3/4 (19.1) 9/16 (14.3) 100/ 6.0 1000/ 61

PART HEAD SIZE DRILL SIZE TOTAL MIN. HEAD HEAD SIZE QTY/WT QTY/WTNUMBER O.D. In. (mm) LENGTH EMBEDMENT HEIGHT I.D. PER BX PER MASTER

In. (mm) In. (mm) In. (mm) In. (mm) lbs. CARTON lbs.

FD4-234 7/16 (11.1) 3/16 (4.8) 2-3/4 (69.9) 3/4 (19.1) N/A N/A 100/ 3.5 1000/ 35


Ultimate Shear and Tension Values (Lbs/kN) in Concrete,Hollow Block and Grout Filled

SHANK DIA. EMBEDMENT 4500 PSI (31.0 MPa) CMU (HOLLOW BLOCK) PSI (MPa) CMU (GROUT FILLED) PSI (MPa)ANCHOR In. (mm) TENSION SHEAR TENSION SHEAR TENSION SHEAR

Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

Redi-Drive/ 3/4 (19.1) 1,215 (5.4) 1,857 (8.3) 382 (1.7) 683 (3.0) 731 (3.3) 1,614 (7.2)

Redi-Form Drive 1 (25.4) 1,667 (7.4) 3,112 (13.8) 392 (1.7) 987 (4.4) 870 (3.9) 1,766 (7.9)

1-1/4 (31.8) 2,373 (10.6) 3,355 (14.9) 398 (1.8) 1,381 (6.1) 1,543 (6.9) 2,778 (12.4)

Tie-Drive or1/4" Pipe-Drive 1-1/4 (31.8) 2,372 (10.6) -- -- -- -- -- -- -- -- -- --

3/8" Pipe-Drive 1-1/2 (38.1) 2,090 (9.3) -- -- -- -- -- -- -- -- -- --

Safe working loads for single installations under static loading conditions should not exceed 25% of the ultimate capacity.

Redi-DriveAnchors

The Redi-Drive is the mostversatile of all of theseproducts. It can be used at all these embedmentdepths and is superior inpull-out performance tothese competitive anchors.

PERFORMANCE TABLE

PERFORMANCE TABLE

*Rawl Spike ® cannot be installed in 3/4” embedment

Rawl Spike ® is a registered trademark of Powers Fastening, Inc.

Embedment in 4500 psi Concrete

PART DESCRIPTION QTY/WT QTY/WTNUMBER PER BOX PER MASTER

CARTON

RDST Redi-Drive Setting Tool 1/1 1/1

Redi-Drive Setting Tool

ACCESSORIESInstalls Redi-Drive anchors in tight and hard to access areas—easily and quickly. Just place anchor in rubber“holding cap,” place against work surface and hammer in anchors.

20 Gauge Metal Deck

Redi-Pipe-DriveInstalled inLower Flute


3/8” Pipe Drive 1/4 (6.4) 1-1/2 (38.1) Upper Flute 1,099 (4.9) 275 (1.2)

Lower Flute 994 (4.4) 249 (1.1)


Anchoring Overhead in 3000 PSILightweight Concrete On Metal Deck

Redi-DriveAnchors


TapconAnchors

ADVANTAGES■ Works in all masonry base materials

■ Fast and easy—3 anchors per minute

■ No hole spotting or inserts required

■ Removable and reusable

■ Slotted hex and phillips flat head styles

■ Excellent corrosion protection—Climaseal™ coated

■ Available in 410 Stainless Steel

ITW Tapcon“The Original”

Hex Head style on Tapcon Anchors is availablefor majority of fixture anchoring needs

Climaseal™ Coating is standard on all Tapconanchors to provide extended corrosion resistance

Now available in 410 Stainless Steel

Phillips Flat Head style is available when flushseating is necessary in countersink applications

Hi-Lo Threads with notches cut into masonrymaterials for greater stability and pullout values

Lengths of Tapcon Anchors range from 1-1/4" to 4" in 3/16" and up to 6" in 1/4" diameters.The tapered shank provides a wedging action for a strong reliable hold

Nail-Type Point guides the anchor into the pre-drilled hole. Excellent for wood to concrete applications

The “original masonry” anchor that cuts its own threads into concrete, brick,or block. Maximum performance is achieved because the Tapcon Anchor,the Condrive Installation Tool, and the carbide-tipped Tapcon Drill Bits aredesigned to work as a system. It is essential to use the Condrive tool and thecorrect drill bit to assure consistent anchor performance.


Tapcon Anchors —SPECIFIED FOR ANCHORAGE INTO CONCRETE, BRICK OR BLOCK®

Tapcon Starter KitStarter Kit Part Number: 7904050Kit Contains:1 Box HW4-1141 Box HW4-1341 Condrive 1000

Tapcon Anchors

TapconSelf-TappingConcreteAnchor


1. With sleeve off and drill bit exposed, drill pilothole 1/4" deeper than recommended anchorembedment. Snap proper anchor socket ontoend of sleeve. Slide drive sleeve over drill bit.

2. Insert head of Tapcon anchor into hex or phillips socket.

INSTALLATION STEPS

3. Put point of anchor into pre-drilled hole anddrive until anchor is fully seated.

Tapcon Anchors

APPROVALS/LISTINGS

ICBO Evaluation Service, Inc. – #ER-3370 (Carbon Steel only)

Metro-Dade County – #00-0118.02


Fixture Thickness—determine the fixture thickness to be anchored

Anchor Embedment—with a minimum recommended embedment of 1", the correctTapcon anchor choice can be made. Holedepth must be a minimum 1/4" deeperthan the anchor embedment to allow fordisplaced material

Hole Diameter—proper hole diameter is very important to insure consistent performance and maximum pulloutstrength. 3/16" anchors require 5/32"diameter bits, and 1/4" anchors require3/16" diameter bits

APPLICATIONS

Tapcon is especially well suited forwindow and door frames because itperforms well in block, is available ina flat head style, and is fast to install.

Many horizontal or “wall” applicationsare attached with Tapcon because it isremovable and works well in block and brick.

The picture shows the Condrive 1000Installation Kit in action. The kit makesfor fast and easy change over from drillbit to driver and controls the drivingtorque to prevent thread stripping andhead snapping in hard base materials.

FEATURES

Head Styles

3/16" Diameter: 1/4" slotted hex washer head (HWH)1/4" Diameter: 5/16" slotted hex washer head (HWH)

3/16" Diameter: #2 phillips flat head (PFH)1/4" Diameter: #3 phillips flat head (PFH)


PART NO. PART NO. PART NO. PART NO. RECOMMENDED FIXTURE BIT BITS FOR BITS FOR BITS FOR BITS FOR3/16" 1/4" 3/16" 1/4" TAPCON LENGTH THICKNESS LENGTH 3/16" TAPCON 1/4" TAPCON 3/16" SDS 1/4" SDS

HEX HEAD HEX HEAD FLAT HEAD FLAT HEAD In. (mm) INCHES In. (mm) PART NO. PART NO. BIT NO. BIT NO.

HW3-114 HW4-114 PF3-114 PF4-114 1-1/4 (31.8) 0" - 1/4" 3-1/2 (88.9) 7900814 7901014 ---- ----

HW3-134 HW4-134 PF3-134 PF4-134 1-3/4 (44.5) 1/4" - 3/4" 3-1/2 (88.9) 7900814 7901014 ---- ----

HW3-214 HW4-214 PF3-214 PF4-214 2-1/4 (57.2) 3/4" - 1-1/4" 4-1/2 (114.3) 7900818 7901018 ---- ----

HW3-234 HW4-234 PF3-234 PF4-234 2-3/4 (69.9) 1-1/4" - 1-3/4" 4-1/2 (114.3) 7900818 7901018 ---- ----

HW3-314 HW4-314 PF3-314 PF4-314 3-1/4 (82.6) 1-3/4" - 2-1/4" 5-1/2 (139.7) 7900822 7901022 ---- ----

---- HW4-334 ---- PF4-334 3-3/4 (95.3) 2-1/4" - 2-3/4" 5-1/2 (139.7) 7900822 7901022 ---- ----

---- HW4-400 ---- PF4-400 4 (101.6) 2-1/2" - 3" 5-1/2 (139.7) 7900822 7901022 ---- ----

---- HW4-500 ---- PF4-500 5 (127.0) 3-1/2" - 4" 6-1/2 (165.1) ---- 7901026 ---- 7901060

---- HW4-600 ---- PF4-600 6 (152.4) 4-1/2" - 5" 7-1/2 (190.5) ---- 7901030 790059 7901059

All boxes of ITW Tapcon come packaged with matching carbide-tipped bit. Tapcon is packaged 100 pieces per box and 500 pieces per master carton except HW4-600 and PF4-600 (400 in master carton).

TapconAnchors

SELECTION CHART

PART NO. PART NO. RECOMMENDED FIXTURE BIT DRILL BIT1/4" 1/4" TAPCON LENGTH THICKNESS LENGTH PART NO.

HEX HEAD FLAT HEAD In. (mm) INCHES In. (mm)

SHW4-114 SPF4-114 1-1/4 (31.8) 0" - 1/4" 3-1/2 (88.9) 3098910

SHW4-134 SPF4-134 1-3/4 (44.5) 1/4" - 3/4" 3-1/2 (88.9) 3098910

SHW4-214 SPF4-214 2-1/4 (57.2) 3/4" - 1-1/4" 4-1/2 (114.3) 309910

SHW4-234 SPF4-234 2-3/4 (69.9) 1-1/4" - 1-3/4" 4-1/2 (114.3) 309910

SHW4-314 SPF4-314 3-1/4 (82.6) 1-3/4" - 2-1/4" 5-1/2 (139.7) 3100910

SHW4-334 SPF4-334 3-3/4 (95.3) 2-1/4" - 2-3/4" 5-1/2 (139.7) 3100910

TapconStainless Steel Anchors

SELECTION CHART

TapconSDS Bits

PART DESCRIPTIONNUMBER

790059 7” (SDS Rotohammer Bits for use with 3/16”Tapcon)



SELECTION CHART


ANCHOR MIN. DEPTH OF f ’c = 2000 PSI (13.8 MPa) f’c = 3000 PSI (20.7 MPa) f’c = 4000 PSI (27.6 MPa) f’c = 5000 PSI (34.5 MPa)DIA. EMBEDMENT TENSION SHEAR TENSION SHEAR TENSION SHEAR TENSION SHEAR

In. (mm) In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

3/16 (4.8) 1 (25.4) 240 (1.1) 740 (3.3) 320 (1.4) 840 (3.7) 400 (1.8) 840 (3.7) 440 (2.0) 860 (3.8)1-1/4 (31.8) 440 (2.0) 780 (3.5) 560 (2.5) 840 (3.7) 600 (2.7) 840 (3.7) 640 (2.8) 860 (3.8)1-1/2 (38.1) 640 (2.8) 820 (3.6) 840 (3.7) 860 (3.8) 880 (3.9) 880 (3.9) 920 (4.1) 900 (4.0)1-3/4 (44.5) 760 (3.4) 920 (4.1) 1,040 (4.6) 1,020 (4.5) 1,120 (5.0) 1,020 (4.5) 1,240 (5.5) 1,020 (4.5)

1/4 (6.4) 1 (25.4) 520 (2.3) 1,120 (5.0) 720 (3.2) 1,460 (6.5) 800 (3.6) 1,560 (6.9) 920 (4.1) 1,660 (7.4)1-1/4 (31.8) 840 (3.7) 1,280 (5.7) 1,120 (5.0) 1,600 (7.1) 1,240 (5.5) 1,660 (7.4) 1,400 (6.2) 1,740 (7.7)1-1/2 (38.1) 1,120 (5.0) 1,280 (5.7) 1,520 (6.8) 1,620 (7.2) 1,600 (7.1) 1,680 (7.5) 1,680 (7.5) 1,760 (7.8)1-3/4 (44.5) 1,320 (5.9) 1,500 (6.7) 1,840 (8.2) 2,140 (9.5) 2,040 (9.1) 2,160 (9.6) 2,240 (10.0) 2,200 (9.8)

Safe working loads for single installation under static loading should not exceed 25% of the ultimate load capacity.The tabulated values are for anchors installed in a minimum of 12 diameters on center and a minimum edge distance of 10 diameters for 100 percent anchor efficiency.

Ultimate Shear and Tension Values (Lbs/kN) in ConcreteTapcon

Anchors

ANCHOR DEPTH OF EMBEDMENT IN SOLID MATERIAL In. (mm)DIA. 1" (25.4) 1-1/4" (31.8) 1-1/2" (38.1) 1-3/4" (44.5)

In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

3/16 (4.8) 209 (0.9) 357 (1.6) 468 (2.1) 547 (2.4)1/4 (6.4) 406 (1.8) 615 (2.7) 851 (3.8) 984 (4.4)

Safe working loads for single installation under static loading should not exceed 25% of the ultimate load capacity.

Ultimate Tension Value (Lbs/kN) in Hollow BlockTapcon

Anchors

ANCHOR ANCHOR SHEAR STRENGTH LIGHTWEIGHTDIA. EMBEDMENT HOLLOW BLOCK

In. (mm) In. (mm) Lbs. (kN)

3/16 (4.8) 1-1/4 (31.8) 731 (3.3)1/4 (6.4) 1-1/4 (31.8) 1,058 (4.7)


Ultimate Shear StrengthTapcon

Anchors

PERFORMANCE TABLE

ANCHOR DEPTH OF EMBEDMENT IN CONCRETE 3000 PSI (20.7 MPa) In. (mm) DEPTH OF EMBEDMENT IN HOLLOW BLOCKDIA. 1" (25.4) 1-1/4" (31.8) 1-1/2" (38.1) 1-3/4" (44.5) 1-1/4" (31.8)

In. (mm) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN) Lbs. (kN)

1/4 (6.4) 1,381 (6.1) 1,618 (7.2) 2,041 (9.1) 2,332 (10.4) 754 (3.4)


Ultimate Tension Value (Lbs/kN) in Concrete and Hollow BlockTapcon

Stainless Steel Anchors

ANCHOR ANCHOR SHEAR STRENGTH HARD ROCK CONCRETE SHEAR STRENGTH LIGHTWEIGHTDIA. EMBEDMENT 3000 PSI (20.7 MPa) HOLLOW BLOCK

In. (mm) In. (mm) Lbs. (kN) Lbs. (kN)

1/4 (6.4) 1-1/4 (31.8) 1,622 (7.2) 1,218 (5.4)


Ultimate Shear StrengthTapcon

Stainless Steel Anchors


InstallationTool Kit

TapconCondrive

Tool Kit

®

PART NO. DESCRIPTION QTY/WT

(A) 7901001 Drill Adapter 1/.06(B) 7901002 Sleeve 1/.01

7901003 Black Band 1/.027901004 5/32" Ball Bearing 1/.02

(C) 7901006 3/16" Socket 1/.04(D) 7901007 1/4" Socket 1/.05

7901008 #2 Phillips bit for 3/16" anchor 1/.107901009 #3 Phillips bit for 1/4" anchor 1/.12

(E) 7901010 Phillips Socket 1/.447902006 Set Screw 1/.027902008 1/16" Ball Bearing 1/.027902010 1/8" Hex Key 1/.10

(Note: 1 matching bit is included in each box of Tapcon anchors. For part numbers see selection chart on page 94 and carbide bits on page 107.)

Condrive 1000Spare Parts

ADVANTAGES■ Fast change from drilling to driving

■ Eliminates need to change out chucks and bits

■ Eliminates need for two tools

■ Special nut driver is recessed for torque controlto reduce head breakage

■ Includes bits for all sizes hex and phillips head

The key to Tapcon’s fast and easy installation is the multi-purpose CondriveInstallation Tool. The drive sleeve, along with the hex head and phillipssockets provide the installer with the flexibility necessary for the completevariety of Tapcon applications.


Condrive 1000 Installation Tool—SPECIFIED FOR ANCHORAGE INTO CONCRETE, BRICK OR BLOCK

APPLICATIONS

The picture shows the Condrive 1000 InstallationKit in action. The kit makes for fast and easychange over from drill bit to driver and controlsthe driving torque to prevent thread strippingand head snapping in hard base materials.

Part No. C1000

(Does not include drill bit)

(D)

(E) (C)

(B)(A)


E-ZAncor

ADVANTAGES

■ Fast—no pre-drilling

■ Easy—just use #2 phillips bit

■ Clean and neat—tri-cut point drills a small hole and seats flush

■ Corrosion resistance

■ Removable—easily backed out of wallboard

■ Breakaway point for easy usage when cavityis shallow

The Original Self-Drilling

Drywall Anchor

APPLICATIONS■ Electrical fixtures

■ HVAC fixtures

■ Bathroom accessories

■ Shelving

■ Closet organizers

■ Curtain rods

■ Signage

The E-Z Ancor is a one-piece self-drilling anchor designed for optimalholding performance in gypsum wallboard. Available in zinc or highstrength engineered plastic (non-conductive). Ideal anchor for 3/8",1/2" and 5/8" gypsum wallboard.


E-Z Ancor Self-Drilling Drywall Anchors— SPECIFIED FOR ANCHORAGE INTO GYPSUM WALLBOARD

E-Z Ancor KitStarter Kit Part Number: EZ25Kit Contains:25 Zinc Anchors25 Screws

™

E-Z AncorSelf-DrillingAnchor


PART DESCRIPTION QTY/WT QTY/WT PERNUMBER PER BOX MASTER CARTON

lbs. lbs.

EZ100 Zinc E-Z Ancor 100/ 1.6 1000/ 17

EZPPL100 Plastic E-Z Ancor 100/ 0.1 1000/ 4.2

EZ25 25 Zinc Anchors/25 Screws (#8 – 1-1/4” sheet metal screw) 1/ 0.9 10/ 10

E-Z Ancor

E-Z Ancor

MAXIMUM ULTIMATE PULLOUT LBS. ULTIMATE SHEAR LBS.FIXTURE GYPSUM BOARD THICKNESS GYPSUM BOARD THICKNESS

THICKNESS 3/8" 1/2" 5/8" 3/8" 1/2" 5/8"

3/4" 40 50 75 135 150 200

E-Z Ancor

1. Place #2 phillips screwdriveror cordless screwdriver (#2 phillips bit) into recess of E-Z Ancor.

2. Press into Gypsum wallboardwhile turning the anchorclockwise until seated flush.

INSTALLATION STEPS3. Place fixture in position over

installed E-Z Ancor. Insert screw (#8A or AB screws are recommended). Tighten fixture into place.

SELECTION CHART

PERFORMANCE TABLE


Hammer-SetAnchors

ADVANTAGES

■ Fast, easy installation

■ Works in concrete, block and brick

■ Install through material to be fastened

■ Low profile mushroom head style

Nail-DriveAnchors


Hammer-Set Nail Drive Anchors— SPECIFIED FOR ANCHORAGE INTO CONCRETE, BLOCK OR BRICK

APPLICATIONSNOT FOR USE IN OVERHEAD APPLICATIONS*

■ Electrical boxes

■ Conduit clips

■ Drywall track

■ Roof flashing* For overhead applications refer to page 88 for Redi-Drive information and performance data

1. Drill hole through material to be fastened into base material.(See selection chart for drill size).

2. Insert Hammer-Set into hole untilhead of anchor body is flush withmaterial to be fastened. Tap the nailuntil flush with head of anchor.

� ��INSTALLATION STEPS

3. Anchor is now set.

APPROVALS/LISTINGS

Meets or exceeds GSA specification FF-S-325 Group V, Type 2, Class 3

The Hammer-Set one-piece zinc plated steel anchor consists of anexpansion body and expander drive pin. Anchors meet or exceed GSAspecification FF-S-325 Group V, Type 2, Class 3.

™

Hammer-SetNail-DriveAnchor


PART DESCRIPTION DRILL MAX. FIXTURE MIN. MIN. QTY/WT QTY/WTNUMBER In. (mm) SIZE THICKNESS EMBEDMENT HOLE SIZE PER BOX PER MASTER

In. (mm) In. (mm) In. (mm) In. (mm) lbs. CTN-lbs.

HS-1607 3/16 x 7/8 (4.8 x 22.2) 3/16 (4.8) 1/4 (6.4) 5/8 (15.9) 1-1/8 (28.6) 100/ 2.0 1000/ 20

HS-1406 1/4 x 3/4 (6.4 x 19.1) 1/4 (6.4) 1/8 (3.2) 5/8 (15.9) 1 (25.4) 100/ 2.2 1000/ 22

HS-1410 1/4 x 1 (6.4 x 25.4) 1/4 (6.4) 1/4 (6.4) 3/4 (19.1) 1-1/4 (31.8) 100/ 2.4 1000/ 24

HS-1412 1/4 x 1-1/4 (6.4 x 31.8) 1/4 (6.4) 1/2 (12.7) 3/4 (19.1) 1-1/2 (38.1) 100/ 2.6 1000/ 26

HS-1414 1/4 x 1-1/2 (6.4 x 38.1) 1/4 (6.4) 3/4 (19.1) 3/4 (19.1) 1-3/4 (44.5) 100/ 2.8 1000/ 28

HS-1420 1/4 x 2 (6.4 x 50.8) 1/4 (6.4) 1-1/4 (31.8) 3/4 (19.1) 2-1/4 (57.2) 100/ 3.5 1000/ 35

Hammer-SetSELECTION CHART

Hammer-Set Anchors

ANCHOR EMBEDMENT 4000 PSI (27.6 MPa)DIA. In. (mm) TENSION SHEAR

In. (mm) Lbs. (kN) Lbs. (kN)

3/16" (4.8) 5/8" (15.9) 640 (2.8) 810 (3.6)

1/4" (6.4) 3/4" (19.1) 935 (4.2) 1,506 (6.7)

1/4" (6.4) 1" (25.4) 1,414 (6.3) 1,506 (6.7)

1/4" (6.4) 1-1/4" (31.8) 1,755 (7.8) 1,506 (6.7)


Hammer-Set

PERFORMANCE TABLE

Bulk Packaging Available

Ultimate Shear and Tension Valuesin Concrete (Lbs/kN)*


Nylon DriveAnchors

Fast Installation,Removable Anchor for

All Types of Masonry

ADHESIVE ANCHORING SYSTEMSADHESIVE ANCHORING SYSTEMS

ADVANTAGES■ Easy to install through part to be fastened

■ Expands by hammering on screw (or drive with a screw gun)

■ Made from Polyamide 6.6 (highly durable nylon)

■ Easy to remove—back out screw

INSTALLATION STEPS

PART ANCHOR ANCHOR BIT SIZE QTY/WT QTY/WT PERNUMBER DIAMETER LENGTH In (mm) PER BOX MASTER CTN

In (mm) In (mm) Lbs Lbs

ND3-100 3/16 (4.8) 1 (25.4) 3/16 (4.8) 100/ 0.6 3500/ 20.5

ND3-134 3/16 (4.8) 1-3/4 (44.5) 3/16 (4.8) 100/ 1.0 3500/ 34.2

ND4-118 1/4 (6.4) 1-1/8 (28.6) 1/4 (6.4) 100/ 0.9 3500/ 31.5

ND4-l34 1/4 (6.4) 1-3/4 (44.5) 1/4 (6.4) 100/ 1.2 3500/ 41.0

ND4-218 1/4 (6.4) 2-1/8 (54.0) 1/4 (6.4) 100/ 1.4 2400/ 34.8

ND-234 1/4 (6.4) 2-3/4 (69.8) 1/4 (6.4) 100/ 1.7 2400/ 40.3

ND5-134 5/16 (7.9) 1-3/4 (44.5) 5/16 (7.9) 100/ 1.9 2400/ 45.5

ND5-238 5/16 (7.9) 2-3/8 (60.3) 5/16 (7.9) 100/ 2.3 1750/ 82.2

ND5-278 5/16 (7.9) 2-7/8 (73.0) 5/16 (7.9) 50/ 2.9 1750/ 102.7

ND5-400 5/16 (7.9) 4 (101.6) 5/16 (7.9) 50/ 3.7 1200/ 89.5

Nylon DriveAnchors

SELECTION CHART

Nylon bodied anchors, can be installed using a hammer or screw gun, forfastening to concrete, concrete block or brick.


Nylon Drive Anchors —SPECIFIED FOR ANCHORAGE INTO CONCRETE, BRICK OR BLOCK

Nylon DriveAnchor

1. Drill hole to anydepth exceedingminimum. Cleanhole.

2. Insert anchorthrough materialto be fastened,flush to work.

3. Drive expanderpin with ahammer.

ANCHOR AVERAGE ULTIMATE LOADS*DIAMETER IN 2000 PSI (13.8 MPa)

In (mm) EMBEDMENT BIT SIZE TENSIONIn (mm) In (mm) Lbs (kN)

3/16 (4.8) 1 (25.4) 3/16 (4.8) 345 (1.5)

1/4 (6.4) 1 (25.4) 1/4 (6.4) 180 (0.8)

1/4 (6.4) 2 (50.8) 1/4 (6.4) 265 (1.2)

5/16 (7.9) 1 (25.4) 5/16 (7.9) 180 (0.8)

5/16 (7.9) 2 (50.8) 5/16 (7.9) 265 (1.2)

5/16 (7.9) 3-1/2 (88.9) 5/16 (7.9) 670 (3.0)

* Allowable loads do not exceed 25% ultimate loads

Nylon DriveAnchors

PERFORMANCE TABLE

Average Ultimate Loadin Concrete (Lbs/kN)*


ADVANTAGES■ Unique twisting action provides superior

holding over standard plug anchors

■ Resistant to moisture, chemicals or atmosphericconditions—can be used anywhere

■ Pre-packaged in kits with matching screws and carbide-tipped drill bit

■ Works well in all base materials

DRYWALL THICKNESS PS-0608S PS-1012S

3/8" 7 - 9 Turns 9 - 11 Turns1/2" 5 - 7 Turns 8 - 9 Turns5/8" 3 - 4 Turns 6 - 7 Turns3/4" 1 - 2 Turns 4 - 5 Turns

1. Drill hole at least 1/4" deeper than anchor length and insertanchor until flange is flush.

For Solid Concrete For Hollow Material

��

��

��

��

��

��

��

��

��

QQQQQQQQQQQQQQQQQQQQQQQQQQQQQQ

��

2. Fasten fixture by insertingsheet metal screw throughfixture and into anchor.

��

��

��

��

��

��

��

��

��

QQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQ

��

3. Tighten screw.

��

��

��

��

��

��

��

��

��

QQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQQ

��

1. Drill hole and insert anchor untilflange is flush.

��

��

��

��

��

��

��

��

��

QQQQQQ

��

��

��

��

��

��

��

��

��

QQQQQQ

��

2. Fasten fixture by inserting sheetmetal screw through fixture andinto anchor.

��

��

��

��

��

��

��

��

��

QQQQQQ

��

��

��

��

��

��

��

��

��

��

QQQQQQQQ

��

3. Expand anchor after screw head isagainst fixture, tighten screw thenumber of additional turns indicatedon the chart below.

��

��

��

��

��

��

��

��

��

QQQQQQ

��

��

��

��

��

��

��

��

��

��

QQQ

��

INSTALLATION STEPS

Approximate number of additional turns after screw head is against fixture for indicated thickness of hollow wall.

Poly-SetAnchors

The Truly Versatile Plug Anchor

DESCRIPTION/SUGGESTED SPECIFICATIONSPlug Anchors — SPECIFIED FOR ANCHORAGE INTO ALL BASE MATERIALS

The Poly-Set is a polyethylene expansion anchor designed for fastening into dry-wall, hollow block, brick and solid concrete.

®Poly-SetPlugAnchor

PART DRILL ANCHOR SCREW GRIP QTY/WT QTY/WT PERNUMBER SIZE LENGTH SIZE RANGE PER BOX (lbs.) MASTER CTN (lbs.)

PS-0608SP 3/16 1-1/4 #6 - 8 3/8 - 3/4 100/ 0.9 1000/ 2

PS-1012SP 9/32 1-7/16 #10 - 12 1/2 - 1 100/ 1.8 1000/ 4

Poly-Set Anchors

PART DRILL KIT CONTAINS GRIP QTY/WT QTY/WT NUMBER SIZE RANGE PER BOX PER MASTER

(lbs.) CTN (lbs.)

PS-0608SKP 3/16 100 1-1/4" anchors/100 #8 screws 3/8 - 3/4 1/ 1.0 10/11

PS-1012SKP 9/32 50 1-7/16" anchors/50 #12 screws 1/2 - 1 1/ 1.2 10/12

Poly-Set Kits

SELECTION CHART

Whatever your concrete anchoring needs, ITW Ramset/Red Head has the high-performance carbide drill bitsyou’ll need. From SDS Plus and A-Taper to Straight Shank carbide bits, you’re assured of 100% performancesatisfaction.

All carbide bits are designed and manufactured with features that produce anywhere from a 25% to a 50%longer bit life. That means your bits go further...so youcan go further and be more productive on the job.

Features include vacuum heat treating, special designflutes and vacuum brazing. And all bits are manufacturedfrom high grade carbide and cobalt for longer bit life.

Included in this section is a handy cross reference chartallowing you to utilize Red Head carbide bits for superiorperformance in all your concrete anchoring systems.

Carbide Bits

100% guaranteed performancemeans you’ll drill more holes,cleaner holes and do it faster…saving you time and money.


Carbide Bits

ADVANTAGES

Carbide Drill Bits for Concrete

Anchoring Systems

DESCRIPTION

Carbide Bits — Anyone can make a carbide bit. It takes a dedicated and confident manufacturer to stand behind their carbide bits with a 100% SatisfactionGuarantee. Not just a guarantee on the quality of the bit, but a 100%Satisfaction Guarantee on the performance of that bit. Take a look at someof the quality built into every bit from Ramset/Red Head.

This quality is built into every bit to give you a performance edge.Ramset/Red Head carbide bits will perform better because of the integrity of the raw materials used and the quality of the manufacturing process. You’ll drill more holes, cleaner holes, and do it faster. That saves you time and money on the job.

ITW Ramset/Red Head guarantees the performance of every bit in their carbide line. This is not just the standard guarantee for warranty against manufacturing defects on the bit. This guarantee includes the PERFORMANCE of that bit...to your 100% satisfaction.

ITW Ramset/Red Head guarantees:

■ Labor savings due to faster drilling ■ Cleaner holes

■ Less vibration and noise ■ Longer bit life and more accurate holes per bit

If you do not agree that your Ramset/Red Head bit performs better than the brand you currently use, we willfully return the price of your purchase or replace the bit.

WHY YOU SHOULD BUY YOUR BITS FROM ITW RAMSET/RED HEAD

ITW Ramset/Red Head has over 75 years of experience, manufacturing and supplying the highest-qualityanchors, chemical anchoring systems, and related drilling products to the construction market. With that typeof background, we know the anchoring market. And we know what it takes to drill, secure and anchor in the toughest substrates. Our expertise in anchoring has led us to deliver the highest quality carbide bits toensure optimum anchoring performance.

From manufacturing chemical epoxy systems, to making almost every conceivable type of anchor for solid concrete, hollow block and brick applications, we have built a reputation for first class products, service and support.

We know what it takes to make a quality bit. We know the steel, the fluting, the carbide tip, the brazing process. And we don’t takeany shortcuts. Rest assured that you can depend on the performance

of Ramset/Red Head carbide bits. We guarantee it.

Ramset/Red HeadCarbide Bits—Every Bit Better


Carbide Bits

FEATURES APPROVALS/LISTINGS

Made to ANSI standardsHL Carbide and Cobalt—Higher density carbideand even distribution of cobalt means your bits staysharper longer for smoother, rounder holes

Special Design Flutes—Special undercut flutingmeans quick and complete dust removal. Cleaner holes mean better anchoring

Vacuum Heat Treating—Evenly tempered andannealed to increase the steel’s strength by 25% at the core for longer bit life

Shot Peening—A “skin-hardening” compressionprocess creates high torque strength and reducesflute wear for longer life

Vacuum Brazing—Solid braze of copper on both the sides and the bottom of the tip, applied in a vacuum oven at 1900° F ensures that the bit tips nevercome out

Multi-Cutter Head Styles—Unique multi-cutterhead for faster dust evacuation allows you to drill 20%faster than standard carbide heads. Two additional cutting tips reduce vibration 60% and increase bit life

Cross-ReferenceSDS PLUS SPLINE SDS MAX STRAIGHT

BOSCH 11211,11212, 11213, 11215, 11202, 11203, 11204, 11205, 11227, 11230, 11231,11236,11239, 11221, 11222, 11219, 11232, 11233, 11244 11233, 11235, 11245

11224, 11225 11228

DEWALT DW004K, DW999K-2, DW562K DW530K, DW531K DW540K, DW541K, DW545KDW565K, DW566K, DW567K, DW532K, DW533K

DW568K, DW570K

METABO 6010, 6011, 6015, 6020, 6021 RH66, RH99, 1129, 6030, 6040, 6046 6045

MAKITA 2010, 2410, HR2400, HR2511 HR3851, HR5000 4000, 5001

RAMSET 425 442, 445, 475

RED HEAD 555, 715 747-2

RYOBI ED160, ED211 PK382

KANGO 220, 240, 340, 360 845S, 850S, 950S 845M, 850M

MILWAUKEE 5303, 5362, 5365, 5311, 5316, 5316-6, 5313-20, 5315, 53465366, 5367, 5368, 5383 5317, 5321, 5345, 5347, 5348

HITACHI DH22VD, DH24PE DH38YE, DH50SB DH40, DH50

HILTI TE2, TE5, TE12, TE15, TE54, TE55, TE75, TE76 TE18, TE22, TE24, TE25

PORTER CABLE 97765

SKIL 642, 6372

ALL THREE JAW CHUCKED DRILL M

OTORS & ROTARY PERCUSSION TOOLS

Bosch® — Robert Bosch Power Tool Corp.DeWalt® —DEWALT Industrial Tool CompanyHilti® — Hilti of America, Inc.Hitachi® — Hitachi Power Tools U.S.A., Ltd.Kango® — Kango Wolf Power Tools, Inc.

Makita® — Makita U.S.A., Inc.Metabo® — Metabo Corp.Milwaukee® — Milwaukee Electric Tool Corp.Porter Cable® — Porter Cable Corporation

Ramset® — Illinois Tool Works (ITW Ramset/Red Head)Red Head® — Illinois Tool Works (ITW Ramset/Red Head)Ryobi®— Ryobi America CorporationQuadro® — Hawera, Inc.

All the following are copyrighted:

SELECTION CHART


SDS PlusPART DIAMETER USABLE OVERALL

NUMBER In. (mm) DRILLING LENGTH LENGTHIn. (mm) In. (mm)

DD-5324 5/32 (4.0) 4 (101.6) 6 (152.4)DD-3162 3/16 (4.8) 2 (50.8) 4 (101.6)DD-3164 3/16 (4.8) 4 (101.6) 6 (152.4)DD-3166 3/16 (4.8) 6 (152.4) 8 (203.2)DD-3168 3/16 (4.8) 8 (203.2) 10 (254.0)DD-142 1/4 (6.4) 2 (50.8) 4 (101.6)DD-144 1/4 (6.4) 4 (101.6) 6 (152.4)DD-146 1/4 (6.4) 6 (152.4) 8 (203.2)DD-148 1/4 (6.4) 8 (203.2) 10 (254.0)DD-5164 5/16 (7.9) 4 (101.6) 6 (152.4)DD-384 3/8 (9.5) 4 (101.6) 6 (152.4)DD-3810 3/8 (9.5) 10 (254.0) 12 (304.8)DD-3816 3/8 (9.5) 16 (406.4) 18 (457.2)DD-7164 7/16 (11.1) 4 (101.6) 6 (152.4)DD-71610 7/16 (11.1) 10 (254.0) 12 (304.8)DD-124 1/2 (12.7) 4 (101.6) 6 (152.4)DD-1210 1/2 (12.7) 10 (254.0) 12 (304.8)DD-1216 1/2 (12.7) 16 (406.4) 18 (457.2)DD-586 5/8 (15.9) 6 (152.4) 8 (203.2)DD-5810 5/8 (15.9) 10 (254.0) 12 (304.8)DD-5816 5/8 (15.9) 16 (406.4) 18 (457.2)DD-346 * 3/4 (19.1) 6 (152.4) 8 (203.2)DD-3410 * 3/4 (19.1) 10 (254.0) 12 (304.8)DD-3416 * 3/4 (19.1) 16 (406.4) 18 (457.2)DD-786 * 7/8 (22.2) 6 (152.4) 8 (203.2)DD-7810 * 7/8 (22.2) 10 (254.0) 12 (304.8)DD-7816 * 7/8 (22.2) 16 (406.4) 18 (457.2)DD-18 * 1 (25.4) 8 (203.2) 10 (254.0)DD-116 * 1 (25.4) 16 (406.4) 18 (457.2)

SDS Facts■ Versatile and popular style

bits fit SDS-drive rotary hammers

■ Lengths and diameters available for virtually every application

■ Stronger shaft and core than industry standard forlonger bit life

■ Extra strong “HL” grade carbide tip means fasterdrilling and longer bit life

■ Made to ANSI standards

■ Available in bulk pack

* Single flute

SDS PlusPART DIAMETER USABLE OVERALL


DD-3164K 3/16 (4.8) 4 (101.6) 6 (152.4)DD-144K 1/4 (6.4) 4 (101.6) 6 (152.4)DD-146K 1/4 (6.4) 6 (152.4) 8 (203.2)DD-5164K 5/16 (7.9) 4 (101.6) 6 (152.4)DD-384K 3/8 (9.5) 4 (101.6) 6 (152.4)DD-124K 1/2 (12.7) 4 (101.6) 6 (152.4)

SELECTION CHART

SELECTION CHART

SDS Plus—Bulk Pack of 25


SDS MaxPART DIAMETER USABLE OVERALL


DSM-128 * 1/2 (12.7) 7 (177.8) 13 (330.2)DSM-1216 * 1/2 (12.7) 18 (457.2) 23 (584.2)DSM-588 5/8 (15.9) 7 (177.8) 13 (330.2)DSM-5816 5/8 (15.9) 18 (457.2) 23 (584.2)DSM-348 3/4 (19.1) 7 (177.8) 13 (330.2)DSM-3416 3/4 (19.1) 18 (457.2) 23 (584.2)DSM-788 7/8 (22.2) 7 (177.8) 13 (330.2)DSM-7816 7/8 (22.2) 18 (457.2) 23 (584.2)DSM-18 1 (25.4) 7 (177.8) 13 (330.2)DSM-116 1 (25.4) 18 (457.2) 23 (584.2)DSM-11812 1-1/8 (28.6) 8 (203.2) 13 (330.2)DSM-11818 1-1/8 (28.6) 18 (457.2) 23 (584.2)DSM-11410 1-1/4 (31.8) 10 (254.0) 15 (381.0)DSM-11418 1-1/4 (31.8) 18 (457.2) 23 (584.2)DSM-13818 1-3/8 (34.9) 18 (457.2) 23 (584.2)DSM-11218 1-1/2 (38.1) 18 (457.2) 23 (584.2)DSM-13418 1-3/4 (44.5) 18 (457.2) 23 (584.2)DSM-218 2 (50.8) 18 (457.2) 23 (584.2)

SDS Max Facts■ Vacuum heat-treated tool steel at core is

25% stronger

■ Vacuum-brazed with pure copper at 1900˚Ffor superior braze and longer bit life

■ Vario flutes with progressive angles forstraighter holes and faster dust removal


Multi-Cutter Head■ Improves bit life by more than 50%

■ Reduces vibration up to 60%

■ Reduces noise up to 30%

■ Extends hammer life

* All bits 1/2" thru 9/16" are single tip carbide; all others are multi-cutter.

SELECTION CHART

Tapcon SDS BitsPART DESCRIPTION

NUMBER

790059 7” (SDS Rotohammer Bits for use with 3/16”Tapcon)7901060 5” (SDS Rotohammer Bits for use with 1/4”Tapcon)7901059 7” (SDS Rotohammer Bits for use with 1/4”Tapcon)

SDS Bits specially designed for use with Condrive 1000 driver tool.

SELECTION CHART


Spline ShankPART DIAMETER USABLE OVERALL


DSS-386 3/8 (9.5) 11 (279.4) 17 (431.8)DSS-7168 7/16 (11.1) 7 (177.8) 12 (304.8)DSS-126 1/2 (12.7) 7 (177.8) 13 (330.2)DSS-1211 1/2 (12.7) 11 (279.4) 17 (431.8)DSS-1218 1/2 (12.7) 17 (431.8) 23 (584.2)DSS-586 5/8 (15.9) 7 (177.8) 13 (330.2)DSS-5811 5/8 (15.9) 11 (279.4) 17 (431.8)DSS-5818 5/8 (15.9) 18 (457.2) 23 (584.2)DSS-346 3/4 (19.1) 7 (177.8) 13 (330.2)DSS-3411 3/4 (19.1) 11 (279.4) 17 (431.8)DSS-3418 3/4 (19.1) 18 (457.2) 23 (584.2)DSS-7811 7/8 (22.2) 11 (279.4) 17 (431.8)DSS-7818 7/8 (22.2) 18 (457.2) 23 (584.2)DSS-111 1 (25.4) 11 (279.4) 17 (431.8)DSS-118 1 (25.4) 18 (457.2) 23 (584.2)DSS-11811 1-1/8 (28.6) 12 (304.8) 18 (457.2)DSS-11818 1-1/8 (28.6) 18 (457.2) 23 (584.2)DSS-11411 1-1/4 (31.8) 11 (279.4) 17 (431.8)DSS-11418 1-1/4 (31.8) 18 (457.2) 23 (584.2)DSS-13811 1-3/8 (34.9) 11 (279.4) 17 (431.8)DSS-13818 1-3/8 (34.9) 18 (457.2) 23 (584.2)DSS-11211 1-1/2 (38.1) 12 (304.8) 18 (457.2)DSS-11218 1-1/2 (38.1) 18 (457.2) 23 (584.2)DSS-13418 1-3/4 (44.5) 18 (457.2) 23 (584.2)DSS-218 2 (50.8) 18 (457.2) 23 (584.2)

Spline Shank Facts■ Splines held to very close tolerances

ensure perfect fit and improvedimpact transmission for faster drilling

■ Vacuum-brazed with pure copper at 1900˚ F for superior braze andlonger bit life

■ Annealed shaft helps prevent breakage

■ Shot peened for torque protection and better wear

■ 25% stronger steel for longer bit life

■ Extra strong grade carbide tip means faster drilling and longer bit life


SELECTION CHART

mechanical anchoring systems · pdf filemechanical anchoring systems ... (ldt ™)...

Documents