method statement for apcs-113a for alloy steel - ---otc - fbe-002

7
Overseas Technical Coatings & Services Company (LLC) OTC/QCP.Doc, MS-IC-002 (Rev 02) Page 1 of 7 KARAN UTI L I TI ES AND CO-GENERATI ON PROJECT  SAUDI ARAMCO CONTRACT 660 0021903 (IK) METHOD STATEMENT FOR SURFACE PREPARATION AND PAINTING ON ALLOY PIPING EXTERNAL SURFACES WITH APCS-113-A MS -IC- 002 Prepared for Approval 09 July, 2011 Rev 02 Date Prepared By Hertel OTC Checked By Reviewed By Approved By

Upload: sharif339

Post on 30-Oct-2015

275 views

Category:

Documents


12 download

DESCRIPTION

msss

TRANSCRIPT

Page 1: Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

7/16/2019 Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

http://slidepdf.com/reader/full/method-statement-for-apcs-113a-for-alloy-steel-otc-fbe-002 1/7

Overseas Technical Coatings & Services Company (LLC)

OTC/QCP.Doc, MS-IC-002 (Rev 02)  Page 1 of 7

KARAN UTI L I TI ES AND CO-GENERATION PROJECT 

SAUDI ARAMCO CONTRACT 6600021903 (IK)

METHOD STATEMENT

FOR 

SURFACE PREPARATION AND PAINTING ON ALLOY

PIPING EXTERNAL SURFACES WITH APCS-113-A

MS -IC- 002

Prepared for 

Approval

09 July, 2011

Rev 02 Date

Prepared

By HertelOTC

CheckedBy

ReviewedBy

ApprovedBy

Page 2: Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

7/16/2019 Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

http://slidepdf.com/reader/full/method-statement-for-apcs-113a-for-alloy-steel-otc-fbe-002 2/7

Overseas Technical Coatings & Services Company (LLC)

OTC/QCP.Doc, MS-IC-002 (Rev 02)  Page 2 of 7

Index 

1. Scope

2. Definitions

3. References

4. Procedure

4.1 Pre-Blast Checks

4.2 Surface Preparation

4.3 Cleaning

4.4 Paint, Storage & Preparation

4.5 Shop & Field Weld joints Paint Application

4.6 Repairs

4.7 Quality Control Procedure

5. Personnel Qualifications

6. Safety

Page 3: Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

7/16/2019 Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

http://slidepdf.com/reader/full/method-statement-for-apcs-113a-for-alloy-steel-otc-fbe-002 3/7

Overseas Technical Coatings & Services Company (LLC)

OTC/QCP.Doc, MS-IC-002 (Rev 02)  Page 3 of 7

1.  SCOPE

This procedure covers minimum requirements of APCS 113A (liquid type epoxy coating) for 

Alloy steel piping on shop application & filed weld joints external coating in buried piping

spools and associated fittings in accordance with SAES-H-002.

2  DEFINITIONS

2.1  COMPANY : SAUDI ARAMCO

2.2  EPC CONTRACTOR : PETROFAC

2.3  CLIENT : MMG

2.4  PROJECT : KARAN UTILITY AND CO-GENERATION

2.5  JOB NO. : 6600021903

2.6  COATING CONTRACTOR : Overseas Technical Coatings & Services (OTC)

3.  REFERENCES 

SAEP-316 : Performance Qualification of Coating Personnel

SAES-H-002 : Internal & external coating of pipeline and piping

SAES-H-002V : Approved Saudi Aramco Data Sheets for the pipelines

Maintenance external coating

SAES-H-100 : Coating Matl’s & Application Requirements for Industrial Facilities 

SAES-H-102 : Safety Requirements for Coating Application

SAES-H-200 : Storage, Handling and Installation of Externally Coated Pipe

SATIP-H-002-06 : Renovation& Repair coating for Submerged Services APCS-113A

09-SAMSS-113 : The requirements of External. Liquid Coatings for Buried P/L & Piping

SSPC-SP1 : Solvent Cleaning Specification

SSPC-SP2 : Hand Tool Cleaning Specification

SSPC-SP3 : Power Tool Cleaning Specification

SSPC-SP10 : Blast Cleaning to Near White Metal Specification

Page 4: Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

7/16/2019 Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

http://slidepdf.com/reader/full/method-statement-for-apcs-113a-for-alloy-steel-otc-fbe-002 4/7

Overseas Technical Coatings & Services Company (LLC)

OTC/QCP.Doc, MS-IC-002 (Rev 02)  Page 4 of 7

SSPC VIS-1 : Pictorial Surface Preparation Standards for Painting Steel Structures

SSPC-PA2 : Measurement of Dry film Thickness

4 PROCEDURE 

4.1  Pre-Blast Check  

4..1.1  QC Inspector shall carry out checks before blasting to determine whether cleaning is requiredeither with the use of chemicals or solvents. Solvent clearing if required shall be carried out in

accordance with SSPC - SPI.

4..1.2   No abrasive blasting shall be carried out unless the steel surface is at least minimum 3°Cabove the Dew Point temperature.

4..1.3  Prior to start for blasting, all sharp edges and cut-offs shall be rounded to a smooth radius andall weld spatters shall be removed.

4..1.4  The compressed air supply shall be checked free of oil, moisture and contamination. As a

minimum, the inspector shall check and approve the air quality at the start & midpoint of each8-hour period. The method of checking shall be in accordance with SAES-H-100 Para 5.4.1

4..1.5  All compressed air hoses and paint lines shall be circular in section, free of cuts, kinks andtwists. Any change in direction shall be by long radius curves to maintain constant and

unrestricted flow where possible.

4..1.6  All hoses and nozzle connections shall be inspected prior to commencement of work to ensurethey are secure. Any defective connection will be immediately replaced.

4.2  Surface Preparation:

4.2.1  Surface preparation shall be carried out in accordance with the relevant coating system as

specified in SAES H-002, APCS-113-A

4.2.2  The type of abrasive to be used shall be determined by degree of cleanliness and surface

Profile requirements as specified in SAES-H-002.

4.2.3  Abrasives shall be kept dry and free of contamination. and shall comply in accordance withSAES-H-100 Para 5.2.1

4.2.4  Sufficient capacity compressors shall be used to supply free air to all elements of the abrasiveand coating operation as per SAES-H-100 Para 5.4

4.2.5  The Blast profile shall be measured with “PRESS-O-FILM” (Testex tape X coarse replicatape) and Profile thickness gauge. The replica tape shall be attached with inspection report as

a permanent record.

Page 5: Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

7/16/2019 Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

http://slidepdf.com/reader/full/method-statement-for-apcs-113a-for-alloy-steel-otc-fbe-002 5/7

Overseas Technical Coatings & Services Company (LLC)

OTC/QCP.Doc, MS-IC-002 (Rev 02)  Page 5 of 7

4.2.6 Residual chloride on the surface shall not exceed 40 mg/m².

Cleaning

4.2.1  Used abrasives shall be removed from external surfaces using a dry brush, blow down withclean dry compressed air.

4.3  Paint, Storage and Preparation

4.3.1  Paint and thinner shall be stored in well – ventilated building at storage temperature as

recommended in the manufacture’s data sheet 

4.3.2  The date of manufacture shall be clearly marked on each paint container and paints that have

exceeded their shelf life shall be discarded

4.3.3  Paints that show signs of leakage or have gelled shall be discarded and any skins that haveformed shall be cut and removed before application. Paint preparation shall be in accordance

with manufacturer’s recommendation and/ or accordance with SAES-H-100- Para-7.

4.3.4  All paints shall be thoroughly mixed before application, quantities over 5 liters shall be mixed

using a power mixer. If the paint cannot be mixed uniformly (thick sediment at the bottom of 

the can) it shall be discarded.

4.4  Paint Application

4.4.1  The prepared surface shall be visually inspected for cleanliness and profile prior to coating.

4.4.2  Prepared surface shall be coated within a maximum of four hours and before any deterioration

 begins. Surfaces that have begun to deteriorate, or have exceeded the four hours shall be re- blasted.

4.4.3  Approved Paint materials for APCS 113-A as per SAES-H-002V shall be used for externalapplication of Alloy spools including associated fittings to specify DFT. WFT will be

monitored to control the required DFT.

4.4.4  Paint shall only be applied if the following conditions are met and as specified by the

Manufacturer:

  Surface temperature to be above 10oC and below 60

oC. Surface temperature to be also

at least minimum 3oC above dew point temperature.

  The surface shall be free of oil, grease, dirt, loose paint, dust, rust and other surface

contaminants.

Page 6: Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

7/16/2019 Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

http://slidepdf.com/reader/full/method-statement-for-apcs-113a-for-alloy-steel-otc-fbe-002 6/7

Overseas Technical Coatings & Services Company (LLC)

OTC/QCP.Doc, MS-IC-002 (Rev 02)  Page 6 of 7

  There is protection from adverse weather conditions, such as winds that may blowsand, or other foreign bodies on the painted surface or it may disrupt the paint pattern

or cause dry spray.

4.4.5  Recoating intervals shall be maintained as per manufacturer’s data sheet. Color contrast between coats shall also be maintained.

4.4.6  Dry film thickness of each coat shall be measured in accordance with SSPC-PA2 using a

suitable non ferrous thickness gauge.

4.4.7  All the work shall be documented for future reference.

4.6 Repairs

4.6.1 All defective areas shall be cleaned with solvents or detergents.

4.6.2 Areas less than 0.1M2

shall be hand abraded or ground back to the surface substrate usingat least 80 grit disc sanders and paint touch up shall be by brush only.

4.6.3 Areas greater than 0.1M2

shall be blast cleaned to original specification and paintapplication shall be airless spray.

4.7 Quality Control Procedure

4.7.1 Quality control requirements are to be carried out in accordance with Inspection and test

 plan of the project. All documents shall be the latest version.

4.7.2 Abrasive blasting/Painting equipment shall be checked by the crew supervisor for 

suitability prior to the start of the surface preparation and coating activities (as per 

approved ITP)

4.7.3  Record on a daily basis critical in process inspection activities.(As per approved ITP)

4.7.4 Paint/Coating and Equipment check list is required to be completed and signed by theCoating Crew Supervisor and verified and signed by the client Inspector 

(As per approved ITP)

4.7.5 TESTEX tape for the profile reading of the blasted area. Minimum 3 tests shall be performed during each shift.

Page 7: Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

7/16/2019 Method Statement for APCS-113A for Alloy Steel - ---Otc - Fbe-002

http://slidepdf.com/reader/full/method-statement-for-apcs-113a-for-alloy-steel-otc-fbe-002 7/7

Overseas Technical Coatings & Services Company (LLC)

OTC/QCP.Doc, MS-IC-002 (Rev 02)  Page 7 of 7

5.  PERSONNEL QUALIFICATION

5.1 OTC personnel involved in preparation, application, direct supervision or inspection of 

coatings shall be qualified and certified by Hertel-OTC and ARAMCO as per SAEP-316.

This includes abrasive blasters, coating applicators, crew supervisors and QC inspectors.

6.  SAFETY. 

6.1  Safety Requirements for Painting shall be observed at all times and shall be strictlyfollowed in accordance with SAES-H-102

6.2  The Project safety plan will be fully enforced during the duration of the work.

6.3  During application process, all lighting will be of the explosion proof type as per SAES-

H-102 item 4.1

6.4  A standby man will be at the work at all times during the work. His role will be observingactivities in the painting work and to stop the work immediately while any safety concern

arises.

6.5  All operators will wear full personal protective equipment including coveralls, safety

 boots, gloves, helmets and positive air feed breathing masks in accordance with SAES-H-

102 item 4.3

6.6  All recommendations of the Material/Equipments manufacturers concerning the safe

handling and application of their products shall be followed as per SAES-H-102 item 4.4.