metroselect configuration guide 02407h
TRANSCRIPT
-
8/12/2019 MetroSelect Configuration Guide 02407H
1/210
-
8/12/2019 MetroSelect Configuration Guide 02407H
2/210
Copyright
2007 by Metrologic Instruments, Inc. All rights reserved. No part of thiswork may be reproduced, transmitted, or stored in any form or by any means
without prior written consent, except by reviewer, who may quote briefpassages in a review, or provided for in the Copyright Act of 1976.
Trademarks
Metrologic is a registered trademark of Metrologic Instruments, Inc.Products identified in this document are hereby acknowledged astrademarks, registered or otherwise, of Metrologic Instruments, Inc. or theirrespective companies.
-
8/12/2019 MetroSelect Configuration Guide 02407H
3/210
Table of Contents iii
TABLE OF CONTENTS
IntroductionSymbol Key ................................................................................................. xi
Bar Code Configuration MethodsSingle-Code Method................................................................................... xiiMulti-Code Method ..................................................................................... xii
Need to Start Over?Recall Defaults ...........................................................................................xiii
Section A: Code Types and Decode RulesUPC/EAN......................................................................................................1 Code 128......................................................................................................3Code 39........................................................................................................4Interleaved 2 of 5..........................................................................................6Standard 2 of 5.............................................................................................9Other 2 of 5 Codes .....................................................................................10Codabar......................................................................................................12 Code 93......................................................................................................13Code 11......................................................................................................13Telepen.......................................................................................................14 Plessey Codes............................................................................................15Other Decode Features..............................................................................17Configurable Code Lengths........................................................................18RSS 14 Features........................................................................................21RSS Limited Features ................................................................................23RSS Expanded Features............................................................................25
-
8/12/2019 MetroSelect Configuration Guide 02407H
4/210
Table of Contents iv
TABLEOFCONTENTSSection B: Supplements
Two Digit Supplements/Redundancy ...........................................................1Five Digit Supplements/Redundancy ...........................................................1Supplements Required/Not Required...........................................................2Remote Supplemental Requirement ............................................................2Bookland (978) Supplement Required .........................................................3977 (2 Digit) Supplement Required ..............................................................3378/379 French Supplement Requirement...................................................3434/439 German Supplement Required.......................................................4414/419 German Supplement Required.......................................................4# System 2 Requires Supplements ..............................................................4# System 5 Requires Supplements ..............................................................58711685 Requires 5-Digit Supplements.......................................................5Coupon Code 128 ........................................................................................5Code 128 Group Separators ........................................................................6Code 128 ]C1 Extended Code Format........................................................6100 msec to Find Supplemental...................................................................6200 msec to Find Supplemental...................................................................6400 msec to Find Supplemental...................................................................7Code IDs with Supplements ........................................................................7Allow 2/5 on 977 Bar Code...........................................................................7Allow 2 on 977 Bar Code..............................................................................7Beep Once/Twice on Supplements .............................................................. 8ISBN Check Digit Transmission ...................................................................8Bookland to ISBN Conversion......................................................................9
-
8/12/2019 MetroSelect Configuration Guide 02407H
5/210
Table of Contents v
TABLEOFCONTENTSISBN Re-Formatting .....................................................................................9
ISSN Check Digit Transmission .................................................................10ISSN Re-Formatting ...................................................................................10977 to ISSN Conversion.............................................................................10Number System 4 Coupon Code 128.........................................................11UPC Discard...............................................................................................11Supplements and UPC in Same Line.........................................................11
Section C: CommunicationsEnable RS-232 .............................................................................................1Load Keyboard Wedge Defaults...................................................................1Enable Light Pen/Wand Communication......................................................1Enable Keyboard Wedge Emulation.............................................................1Enable Stand-Alone Keyboard Scanner.......................................................1Load OCIA Defaults......................................................................................2Enable OCIA Output.....................................................................................2Load IBM 46xx Defaults ...............................................................................2Enable IBM 46xx Communication ................................................................2Low Speed USB ........................................................................................... 3Enable No Communication Mode.................................................................3Reserved ......................................................................................................3
Section D: Scanner OperationConfiguration Mode Options.........................................................................1Scan Buffers.................................................................................................2Redundant Scans.........................................................................................4Miscellaneous Decode Features ..................................................................6Depth of Field Adjustments ..........................................................................7
-
8/12/2019 MetroSelect Configuration Guide 02407H
6/210
Table of Contents vi
TABLEOFCONTENTSSame Symbol Time Outs..............................................................................8Barcode Absence .........................................................................................9LED Options ...............................................................................................10Beeper Options...........................................................................................12Inter-Character Data Transmission Delays ................................................17Inter-Record Data Transmission Delays.....................................................18Communication Time Out Options ............................................................. 19Host Scanner Commands ..........................................................................21Power Save Modes ....................................................................................26Japanese Double Field Support .................................................................30Test Modes.................................................................................................35
Section E: Prefixes/SuffixesConfigurable Prefixes, All Data.....................................................................1Configurable ID Characters, Code Specific..................................................3
Identifiers Character ...........................................................................3Standard Prefix Characters ..........................................................................8Standard Suffix Characters ........................................................................14Longitudinal Redundancy Check (LRC) .....................................................16Configurable Suffixes, All Data...................................................................17Special Formats..........................................................................................20Character Replacements............................................................................21
Section F: Code FormattingUPC/EAN......................................................................................................1 Codabar........................................................................................................5 Code 39........................................................................................................7Code 11........................................................................................................9
-
8/12/2019 MetroSelect Configuration Guide 02407H
7/210
Table of Contents vii
TABLEOFCONTENTSTelepen.........................................................................................................9
Plessey.......................................................................................................10 2 of 5...........................................................................................................12
Section G: RS-232Enable RS-232 Mode ...................................................................................1Parity Features .............................................................................................2Baud Rates...................................................................................................3Data/Stop Bits...............................................................................................5Hardware Handshaking................................................................................6Software Handshaking .................................................................................9Miscellaneous.............................................................................................12
Section H: KeyboardEnable Keyboard Emulation.........................................................................1Country/Scan Code Table Selects ...............................................................2Keyboard/System Type ................................................................................4Special Keyboard Features ..........................................................................5Inter-Scan Code Delays ...............................................................................9Control Sets................................................................................................103151 Terminal Keyboard ............................................................................12
Section I: OCIALoad OCIA Defaults......................................................................................1Enable OCIA.................................................................................................1DTS/Siemens ...............................................................................................1DTS/Nixdorf..................................................................................................1 NCR-S ..........................................................................................................1NCR-F ..........................................................................................................1
-
8/12/2019 MetroSelect Configuration Guide 02407H
8/210
Table of Contents viii
TABLEOFCONTENTSSection J: Light Pen/Laser Emulation
Enable Light Pen Mode ................................................................................1Space/Bar Height .........................................................................................1Transmit Code 39.........................................................................................1Transmit as Scanned....................................................................................1Poll Light Pen Source...................................................................................2Light Pen Extra Toggle.................................................................................210x Narrow Element Border .........................................................................250x Narrow Element Border .........................................................................2Set Narrow Element Width ...........................................................................3Laser Emulation............................................................................................3
Section K: IBM 46xx ConfigurationEnable IBM 46xx Communication ................................................................1Load IBM 46xx Defaults ...............................................................................1IBM Ports......................................................................................................1IBM Reserve Codes .....................................................................................2
Section M: Code BytesCode Byte Usage .........................................................................................1Code Bytes 0-5.............................................................................................2Code Bytes 6-9.............................................................................................3Reserved Codes...........................................................................................4Code Byte/Code Type Table ........................................................................5
ASCII Reference Table.................................................................................6Extended Key Code Reference Table........................................................11
-
8/12/2019 MetroSelect Configuration Guide 02407H
9/210
Table of Contents ix
TABLEOFCONTENTS
Section N: Miscellaneous FeaturesCustom Defaults...........................................................................................1Serial Configuration Mode............................................................................5Software/Serial Number ...............................................................................5
Section O: Auxiliary Port ControlsDisable AUX Port..........................................................................................1AUX Port and Secondary Device Data Formats
When Using a Metrologic Device as a Secondary..............................1When Using a Non-Metrologic RS-232 Device as a Secondary.........3
Additional AUX Port Data Formats...............................................................4AUX Port Baud Rates...................................................................................5AUX Port Parity ............................................................................................7AUX Port Stop/Data Bits...............................................................................8Enable/Disable RTS/CTS Handshaking.......................................................9Message AUX RTS/CTS ..............................................................................9Character AUX RTS/CTS.............................................................................9Enable/Disable Port Mode 7.........................................................................9Enable/Disable D/E Commands.................................................................10Enable/Disable F/L Commands..................................................................10Enable/Disable M/O Commands ................................................................10Enable/Disable XON/XOFF Handshaking..................................................11Enable/Disable ACK/NAK...........................................................................11AUX CTS/RTS Polarity...............................................................................12AUX Same Symbol Timeout.......................................................................12Main Output Port Auxiliary Data Formats...................................................13
-
8/12/2019 MetroSelect Configuration Guide 02407H
10/210
Table of Contents x
TABLEOFCONTENTSInter-Character Delays ...............................................................................15Inter-Character De lays ..............................................................................16
Section P: USB .................................................................................................. 1Section R: IS3480 / MS3580 / MS3780
Button Modes ............................................................................................... 1Button Click Delay ........................................................................................1Primary and Secondary Scan Patterns ........................................................2Sweet Spot Mode (IS3480) ..........................................................................4CodeGate (IS3480 / MS3580)......................................................................4Depth of Field ...............................................................................................4IR Activation .................................................................................................5TTL RS232 ...................................................................................................5CodeGate (MS3780) ....................................................................................6Modes (MS3780)..........................................................................................7
Section S: Protocol FormattingROM Emulation ............................................................................................1
-
8/12/2019 MetroSelect Configuration Guide 02407H
11/210
Introduction xi
INTRODUCTION
Your new scanner has been configured at the factory with a set of default communicationprotocols. Since many host systems have unique formats and protocol requirements,Metrologic provides a wide range of configurable features that may be selected with theuse of this bar code configuration guide.
Once the configuration is completed, the scanner stores the settings in nonvolatilememory or NOVRAM. NOVRAM saves the settings when the power is turned off.
Symbol Key
* (asterisk) Default Feature
~ (tilde)Feature requires the Multi-CodeConfiguration Method,
see Bar Code Configuration Methods on page xii.
Important!
Note
-
8/12/2019 MetroSelect Configuration Guide 02407H
12/210
Bar Code Configuration Methods xii
BAR CODE CONFIGURATION METHODS
Metrologic scanners can be bar code configured in two ways: the Single-Code Method
and the Multi-Code Method.
Single-CodeMethod
Most features can be enabled or disabled using the Single-Code Method.
1. Power up the scanner.
2. Scan the bar code(s) for the desired feature(s).3. Observe a multi-toned, save setting beep that indicates the configuration has
been saved to NOVRAM.
Multi-CodeMethod
All features can be enabled or disabled using the Multi-Code Method.A feature marked with a ~ requires the Multi-Code Method.
1. Power up the scanner.
2. Scan the Enter/Exit Configuration Modebar code. [3 beeps]
3. Scan the bar code(s) for the desired feature(s). [1 beep]
4. Scan the Enter/Exit Configuration Modebar code [3 beeps] andsave new configuration.
Enter/Exit Configuration Mode
9 9 9 9 9 9
To abort a configuration change, power off the scanner before scanning theEnter/Exit Configuration Modebar code.
-
8/12/2019 MetroSelect Configuration Guide 02407H
13/210
Need to Start Over? xiii
NEED TO START OVER?
Scan the Recall Default bar code. This will erase all previous settings and return to thescanners default communications protocol.
Keyboard Wedge interface scanners will load keyboard wedge defaults. All other scanners will load RS232 defaults.
Metrologic manufactures custom OEM scanners, which load the OEMsdefaults. For further information on the affects they have on Metrologic defaultcommunications protocols refer to Section N, Custom Defaults.
Recall Defaults
9 9 9 9 9 8
-
8/12/2019 MetroSelect Configuration Guide 02407H
14/210
-
8/12/2019 MetroSelect Configuration Guide 02407H
15/210
Code Types & Decode Rules A 1
SECTIONA UPC/EAN
* Enable UPC/EAN Disable UPC/EAN
1 0 0 1 1 6 1 0 0 1 0 6
* Enable UPC-A Disable UPC-A
1 0 0 2 1 6 1 0 0 2 0 6
* Enable UPC-E Disable UPC-E
1 0 0 2 1 0 1 0 0 2 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
16/210
Code Types & Decode Rules A 2
SECTIONA UPC/EAN
* Enable EAN-13 Disable EAN-13
1 0 0 2 1 1 1 0 0 2 0 1
* Enable EAN-8 Disable EAN-8
1 0 0 2 1 4 1 0 0 2 0 4
* EnableAuto Redundancy UPC-E
DisableAuto Redundancy UPC-E
1 0 1 1 0 4 1 0 1 1 1 4
-
8/12/2019 MetroSelect Configuration Guide 02407H
17/210
Code Types & Decode Rules A 3
SECTIONA CODE 128
* Enable Code 128 Disable Code 128
1 0 0 1 1 3 1 0 0 1 0 3
EnableUCC/EAN-28]C1 Code Formatting
DisableUCC/EAN-128]C1 Code Formatting
1 0 0 3 1 4 1 0 0 3 0 4
For Coupon Code 128, see Section B, page 5.
-
8/12/2019 MetroSelect Configuration Guide 02407H
18/210
Code Types & Decode Rules A 4
SECTIONA CODE 39
* Enable Code 39 Disable Code 39
1 0 0 1 1 1 1 0 0 1 0 1
Enable MOD 43Check on Code 39
* Disable MOD 43Check on Code 39
1 0 0 2 1 3
The scanner will only scanCode 39 bar codes thathave a valid Modulo 43check digit.
1 0 0 2 0 3
The scanner will not testCode 39 bar codes for amodulo 43 check digit.
Transmit Mode 43 CheckDigit on Code 39
* Do Not Transmit Mode 43Check Digit on Code 39
1 0 7 7 1 5
This feature works inconjunction with Mode 43Check on Code 39. Bothoptions must be enabled for
this feature to work.
1 0 7 7 0 5
This option will not transmitCode 39s Mod 43 checkcharacter.
-
8/12/2019 MetroSelect Configuration Guide 02407H
19/210
Code Types & Decode Rules A 5
SECTIONA CODE 39
Enable Full ASCII Code 39 * Disable Full ASCIICode 39
1 0 0 2 1 7 1 0 0 2 0 7
Enable PARAF Support(Italian Pharmaceutical Codes) * Disable PARAF Support
1 0 0 2 1 5
The scanner will convertCode 39 bar codes toPARAF format.
1 0 0 2 0 5
The scanner will not convertcode 39 bar codes toPARAF format.
Enable TRI-OPTIC Code * Disable TRI-OPTIC Code
1 0 0 3 1 2 1 0 0 3 0 2
-
8/12/2019 MetroSelect Configuration Guide 02407H
20/210
Code Types & Decode Rules A 6
SECTIONA INTERLEAVED 2OF 5
* Enable Interleaved
2 of 5 (ITF)
Disable Interleaved
2 of 5 (ITF)
1 0 0 1 1 5 1 0 0 1 0 5
Enable MOD 10Check on ITF
* Disable MOD 10Check on ITF
1 0 0 3 1 0
The scanner will only scanInterleaved 2 of 5 (ITF)Bar codes that have aModulo 10 check digit.
1 0 0 3 0 0
The scanner will not testInterleaved 2 of 5 (ITF)bar codes for a Modulo 10check digit.
Transmit MOD 10Check Digit on ITF
* Do Not Transmit MOD 10Check Digit on ITF
1 0 7 7 1 4
The scanner transmitsInterleaved 2 of 5 (ITF)MOD 10 check character.
1 0 7 7 0 4
The scanner will nottransmit Interleaved 2 of 5(ITF) MOD 10 check digitcharacters. This featureworks in conjunction withMod 10 Check on ITF. Bothmust be enabled for this
feature to work.
-
8/12/2019 MetroSelect Configuration Guide 02407H
21/210
Code Types & Decode Rules A 7
SECTIONA INTERLEAVED 2OF 5
Enable ALTCheck Digit ITF
* Disable ALTCheck Digit ITF
1 0 0 7 1 7 1 0 0 7 0 7
Enable 12 Digit ITFCheck Digit at 1 * Normal Check Digit
1 0 0 9 1 0
This feature requiresMOD 10 ITF Check Digittobe enabled. The 12-
character ITF check digitcalculation will start with 1instead of 0.
1 0 0 9 0 0
Enable ITF/Code 39 Filter* Disable ITF/Code 39
Filter
1 0 0 4 1 6
Supports Code 39/ITF filters.
This feature may adverselyaffect reading Codabar,Code 93 and some othernon-standard symbologies.
1 0 0 4 0 6
-
8/12/2019 MetroSelect Configuration Guide 02407H
22/210
Code Types & Decode Rules A 8
SECTIONA INTERLEAVED 2OF 5
~ ITF Symbol Length
Lock 1
~ ITF Symbol Length
Lock 2
9 0 1 6 0 0
To specify a 1stITF symbol
length lock, scan the abovebar code and theappropriate code byteslocated in Section M.
9 0 1 7 0 0
To specify a 2ndITF symbol
length lock, scan the abovebar code and theappropriate code byteslocated in Section M.
~ ITF MinimumSymbol Length
9 0 3 4 0 0 To specify a minimumnumber of ITF characters tobe decoded, scan the abovebar code and theappropriate code byteslocated in Section M.
Refer to the Multi-CodeConfiguration Method onpage xii.
-
8/12/2019 MetroSelect Configuration Guide 02407H
23/210
Code Types & Decode Rules A 9
SECTIONA STANDARD 2OF 5
EnableStandard 2 of 5
* DisableStandard 2 of 5
1 0 0 1 1 0 1 0 0 1 0 0
~ Standard 2 of 5Symbol Length Lock
9 0 1 5 0 0
To specify a minimumnumber of ITF characters tobe decoded, scan the abovebar code and theappropriate code byteslocated in Section M.
Refer to the Multi-Code configurationmethod on page xii.
-
8/12/2019 MetroSelect Configuration Guide 02407H
24/210
Code Types & Decode Rules A 10
SECTIONA OTHER 2OF 5CODES
Enable Matrix 2 of 5 * Disable Matrix 2 of 5
1 0 0 0 1 5 1 0 0 0 0 5
Enable 15 Digit
Airline 2 of 5
* Disable 15 Digit
Airline 2 of 5
1 0 0 0 1 4 1 0 0 0 0 4
-
8/12/2019 MetroSelect Configuration Guide 02407H
25/210
Code Types & Decode Rules A 11
SECTIONA OTHER 2OF 5CODES
Enable 13 DigitAirline 2 of 5
* Disable 13 DigitAirline 2 of 5
1 0 0 3 1 3 1 0 0 3 0 3
Enable Hong Kong2 of 5
* Disable Hong Kong2 of 5
1 0 0 3 1 6 1 0 0 3 0 6
-
8/12/2019 MetroSelect Configuration Guide 02407H
26/210
Code Types & Decode Rules A 12
SECTIONA CODABAR
* Enable Codabar * Disable Codabar
1 0 0 1 1 4 1 0 0 1 0 4
EnableDual Field Codabar
* DisableDual Field Codabar
1 0 0 0 1 2 1 0 0 0 0 2
EnableTab in Dual Codabar
* DisableTab in Dual Codabar
1 0 8 0 1 2
This feature requires DualField Codabar to beenabled. The scanner willinsert a tab between thefields of the dual fieldCodabar.
1 0 8 0 0 2
-
8/12/2019 MetroSelect Configuration Guide 02407H
27/210
Code Types & Decode Rules A 13
SECTIONA CODE 93AND CODE 11
* Enable Code 93 Disable Code 93
1 0 0 1 1 2 1 0 0 1 0 2
Enable Code 11 * Disable Code 11
1 0 0 0 1 3 1 0 0 0 0 3
-
8/12/2019 MetroSelect Configuration Guide 02407H
28/210
Code Types & Decode Rules A 14
SECTIONA TELEPEN
Enable Telepen * Disable Telepen
1 0 0 0 1 7 1 0 0 0 0 7
EnableALPHA Telepen
* DisableALPHA Telepen
1 0 0 0 1 6 1 0 0 0 0 6
-
8/12/2019 MetroSelect Configuration Guide 02407H
29/210
Code Types & Decode Rules A 15
SECTIONA PLESSEY CODES
Enable MSI Plessey * Disable MSI Plessey
1 0 0 2 1 2 1 0 0 2 0 2
* No MSI PlesseyCheck Digit
2 0 0 7 0 4
The scanner will not testMSI Plessey bar codes for acheck digit.
Enable MSI PlesseyMOD 10/10 Check Digit
* Enable MSI Plessey MOD10 Check Digit
2 0 0 7 3 4
The scanner will test MSIPlessey bar codes for adouble Modulo 10 check
digit.
2 0 0 7 2 4
The scanner will test MSIPlessey bar codes for asingle Modulo 10 check
digit.
-
8/12/2019 MetroSelect Configuration Guide 02407H
30/210
Code Types & Decode Rules A 16
SECTIONA PLESSEY CODES
Transmit
MSI Plessey Check Digit
* Do Not Transmit
MSI Plessey Check Digit
1 0 7 7 1 1
This option works in
conjunction with one or bothof the Enabled MSI PlesseyMode options.
1 0 7 7 0 1
The scanner will not
transmit MSI Plessey checkdigit characters.
Enable UK Plessey * Disable UK Plessey
1 0 0 1 1 7 1 0 0 1 0 7
Enable UK PlesseyA to X Conversion
* Disable UK PlesseyA to X Conversion
1 0 0 7 1 6 1 0 0 7 0 6
-
8/12/2019 MetroSelect Configuration Guide 02407H
31/210
Code Types & Decode Rules A 17
SECTIONA OTHER DECODE FEATURES
Enable Double BorderRequired/LargeInter-Character Space
* Disable Double BorderRequired/LargeInter-Character Space
1 0 0 0 1 1 1 0 0 0 0 1
~ MinimumSymbol Length
~ Symbol Length Lock
9 0 1 8 0 0
Omnidirectional default is 4.Combine this code with theproper Code Bytes, tospecify the minimumnumber of characters in allnon-UPC/EAN bar codes.
9 0 1 9 0 0
This code combined with theproper Code Bytes, locks thebar codes length into place.
Refer to the Multi-Code Configuration Method on page xii.
-
8/12/2019 MetroSelect Configuration Guide 02407H
32/210
Code Types & Decode Rules A 18
SECTIONA CONFIGURABLE CODE LENGTHS
There are seven bar code lock lengths available. Specific code types can be assigned to
a lock length using the Multi-Codeconfiguration method.
Example:
1. Scan the enter/exit configuration bar code.
2. Scan the code length lock #1bar code.
3. Scan the three Code Bytes that represent the code length.
4. Scan the matching code type lock #1 bar code.
5. Scan the three code bytes that represent the code type.
Refer to the Code Type Tablein Section M.
6. Repeat steps 2 through 5 for lock lengths 2 through 7 if desired.
7. Scan the enter/exit configuration bar code when finished to save settings.
~ Code LengthLock #1
~ Code TypeLock #1
9 0 2 0 0 0 9 0 2 1 0 0
~ Code Length
Lock #2
~ Code Type
Lock #2
9 0 2 2 0 0 9 0 2 3 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
33/210
Code Types & Decode Rules A 19
SECTIONA CONFIGURABLE CODE LENGTHS
~ Code LengthLock #3
~ Code TypeLock #3
9 0 2 4 0 0 9 0 2 5 0 0
~ Code LengthLock #4
~ Code TypeLock #4
9 0 2 6 0 0 9 0 2 7 0 0
~ Code LengthLock #5
~ Code TypeLock #5
9 0 2 8 0 0 9 0 2 9 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
34/210
-
8/12/2019 MetroSelect Configuration Guide 02407H
35/210
Code Types & Decode Rules A 21
SECTIONA RSS14FEATURES
Enable RSS 14 * Disable RSS 14
1 0 0 4 1 3 1 0 0 4 0 3
* Transmit
RSS 14 Check Digit
Do Not Transmit
RSS 14 Check Digit
1 1 4 9 0 0 1 1 4 9 1 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
36/210
Code Types & Decode Rules A 22
SECTIONA RSS14FEATURES
* Transmit
RSS 14 Application ID
Do Not Transmit
RSS 14 Application ID
1 1 4 9 0 1
Application identifier 01 is
transmitted by default.
1 1 4 9 1 1
* TransmitRSS 14 Symbology ID
Do Not TransmitRSS 14 Symbology ID
1 1 4 9 0 2
Symbology identifier ]e0 istransmitted by default.
1 1 4 9 1 2
-
8/12/2019 MetroSelect Configuration Guide 02407H
37/210
Code Types & Decode Rules A 23
SECTIONA RSSLIMITED FEATURES
Enable RSS Limited * Disable RSS Limited
1 0 0 4 1 4 1 0 0 4 0 4
* TransmitRSS Limited Check Digit
Do Not TransmitRSS Limited Check Digit
1 1 4 9 0 3 1 1 4 9 1 3
-
8/12/2019 MetroSelect Configuration Guide 02407H
38/210
Code Types & Decode Rules A 24
SECTIONA RSSLIMITED FEATURES
* Transmit RSS Limited
Application ID
Do Not Transmit
RSS Limited Application ID
1 1 4 9 0 4
Application identifier 01 is
transmitted by default.
1 1 4 9 1 4
* Transmit RSS LimitedSymbology ID
Do Not TransmitRSS Limited Symbology ID
1 1 4 9 0 5
Symbology identifier ]e0 istransmitted by default.
1 1 4 9 1 5
-
8/12/2019 MetroSelect Configuration Guide 02407H
39/210
Code Types & Decode Rules A 25
SECTIONA RSSEXPANDED FEATURES
Enable RSS Expanded * Disable RSS Expanded
1 0 0 4 1 5 1 0 0 4 0 5
* Transmit RSSExpanded Symbology ID
Do Not Transmit RSSExpanded Symbology ID
1 1 4 9 0 6
Symbology identifier ]e0 istransmitted by default.
1 1 4 9 1 6
-
8/12/2019 MetroSelect Configuration Guide 02407H
40/210
-
8/12/2019 MetroSelect Configuration Guide 02407H
41/210
-
8/12/2019 MetroSelect Configuration Guide 02407H
42/210
Supplements B 2
SECTION B SUPPLEMENTS/REDUNDANCY
Enable Five Digit
Redundancy
* Disable Five Digit
Redundancy
1 0 1 2 1 1
Twice before accepting
data, the scanner will scanthe bar code plus the fivedigit add on.
1 0 1 2 0 1
The scanner will not
implement the five digitredundancy feature.
Supplementsare Required
* Supplements arenot Required
1 0 1 2 1 3
All UPC/EAN labels that arescanned must have asupplement.
1 0 1 2 0 3
UPC/EAN labels do notrequire a supplement to bescanned.
Enable RemoteSupplemental Requirement
* DisableRemote SupplementalRequirement
1 0 1 4 1 6 1 0 1 4 0 6
-
8/12/2019 MetroSelect Configuration Guide 02407H
43/210
Supplements B 3
SECTION B SUPPLEMENTS
Enable Bookland (978)Supplement Requirement
* Disable Bookland (978)Supplement Requirement
1 0 1 4 1 7 1 0 1 4 0 7
Enable 977 (2 digit)
Supplemental Requirement
* Disable 977 (2 digit)SupplementalRequirement
1 0 1 3 1 4
The scanner will require a2 digit supplement bescanned when an EAN-13code begins with 977.
1 0 1 3 0 4
The scanner will notrequire a 2 digit supplementbe scanned whenever anEAN-13 code begins with977.
Enable 378/379 FrenchSupplement Requirement
* Disable 378/379 FrenchSupplemental Requirement
1 0 1 3 1 3 1 0 1 3 0 3
-
8/12/2019 MetroSelect Configuration Guide 02407H
44/210
Supplements B 4
SECTION B SUPPLEMENTS
Enable 434/439 GermanSupplemental Requirement
* Disable 434/439
German SupplementalRequirement
1 0 1 4 1 5 1 0 1 4 0 5
Enable 414/419 GermanSupplemental Requirement
* Disable 414/419 GermanSupplemental Requirement
1 0 1 4 1 3 1 0 1 4 0 3
Enable # System 2 RequiresSupplements
* Disable # System 2Requires Supplements
1 0 1 4 1 2 1 0 1 4 0 2
-
8/12/2019 MetroSelect Configuration Guide 02407H
45/210
Supplements B 5
SECTION B SUPPLEMENTS
Enable # System 5 RequiresSupplements
* Disable # System 5Requires Supplements
1 0 1 2 1 5 1 0 1 2 0 5
Enable 8711685 Requires5-Digit Supplement
* Disable 8711685Requires 5-DigitSupplement
1 0 7 6 1 3
The scanner will require a5-digit supplement to be
scanned when an EAN-13code begins with 8711685.
This feature is notavailable with allmodels.
1 0 7 6 0 3
The scanner will not requirea 5-digit supplement to be
scanned when an EAN-13code begins with 8711685.
Enable CouponCode 128
* Disable CouponCode 128
1 0 0 3 1 5 1 0 0 3 0 5
-
8/12/2019 MetroSelect Configuration Guide 02407H
46/210
Supplements B 6
SECTION B SUPPLEMENTS
Enable Code 128 ]C1
Extended Code Format
* Disable Code 128 ]C1
Extended Code Format
1 0 1 4 1 1
The scanner will transmit a
]C1 at the beginning of thecode 128 portion of thecoupon code.
1 0 1 4 0 1
The scanner will not
transmit a ]C1 at thebeginning of the code 128portion of the coupon code.
Enable 128 GroupSeparators
* Disable 128 GroupSeparators
1 0 1 4 1 4
GS (1DH) character will betransmitted with couponCode 128 codes.
1 0 1 4 0 4
GS (1DH) character willnot be transmitted withcoupon Code 128 codes.
* 100 msec to FindSupplemental
200 msec to FindSupplemental
3 0 1 3 1 0
The scanner will allot 100milliseconds to find an addon after a main UPC/EANbar code has been scanned.
3 0 1 3 2 0
The scanner will allot 200milliseconds to find an addon after a main UPC/EANbar code has been scanned.
-
8/12/2019 MetroSelect Configuration Guide 02407H
47/210
Supplements B 7
SECTION B SUPPLEMENTS
400 msec to FindSupplemental
3 0 1 3 4 0
The scanner will allot 400milliseconds to find an addon after a main UPC/EANbar code has been scanned.
Enable Code IDs with
Supplements
* Disable Code IDs with
Supplements
1 0 1 2 1 4 1 0 1 2 0 4
Allow 2/5 on 977 Bar Code Allow 2 on 977 Bar Code
1 2 4 8 1 1
This feature allows either2 or 5 digit supplements if
977 mode is active.
1 2 4 8 0 1
This feature allows 2 digitsupplements if 977 mode is
active.
-
8/12/2019 MetroSelect Configuration Guide 02407H
48/210
Supplements B 8
SECTION B SUPPLEMENTS
* Beep Once on
Supplements
Beep twice on
Supplements
1 1 8 4 0 6 1 1 8 4 1 6
Enable ISBN Check DigitTransmission
Disable ISBN Check DigitTransmission
1 0 1 3 1 5
This feature is notavailable with allmodels.
1 0 1 3 0 5
-
8/12/2019 MetroSelect Configuration Guide 02407H
49/210
Supplements B 9
SECTION B SUPPLEMENTS
Enable Bookland toISBN Conversion
* Disable Bookland toISBN Conversion
1 0 1 3 1 7
This feature is notavailable with allmodels.
1 0 1 3 0 7
EnableISBN Re-Formatting
* DisableISBN Re-Formatting
1 0 1 3 1 6
This feature is notavailable with allmodels.
1 0 1 3 0 6
-
8/12/2019 MetroSelect Configuration Guide 02407H
50/210
Supplements B 10
SECTION B SUPPLEMENTS
Enable ISSN Check Digit
Transmission
* Disable ISSN Check Digit
Transmission
1 1 5 1 1 5 1 1 5 1 0 5
EnableISSN Re-Formatting
* DisableISSN Re-Formatting
1 1 5 1 1 6
Transmit a hyphen with thebarcode.
1 1 5 1 0 6
Enable 977 to
ISSN Conversion
* Disable 977 to
ISSN Conversion
1 1 5 1 1 7
Convert 977 periodicals to
ISSN format.
1 1 5 1 0 7
Do not convert 977
periodicals to ISSN format.
-
8/12/2019 MetroSelect Configuration Guide 02407H
51/210
Supplements B 11
SECTION B SUPPLEMENTS
Enable Number System 4Coupon Code 128
* Disable Number System4 Coupon Code 9128
1 0 1 0 1 2
Supports Coupon Code 128for Number System 4 barcodes.
1 0 1 0 0 2
Enable UPC Discard * Disable UPC Discard
1 0 1 0 1 3
Supports UPC discard if theCode 128 portion of theCoupon Code 128 is
scanned.
1 0 1 0 0 3
Allow Supplements andUPC in Same Line
Disable Supplements andUPC in Same Line
1 0 1 0 1 4
This feature requires2 digit supplements beenabled as well asrequired redundancyand supplements.
1 0 1 0 0 4
-
8/12/2019 MetroSelect Configuration Guide 02407H
52/210
-
8/12/2019 MetroSelect Configuration Guide 02407H
53/210
Communications C 1
SECTION C COMMUNICATIONS
* Enable RS-232 Load Keyboard WedgeDefaults
4 1 5 5 5 4
The scanner will work with
RS-232 12V serial output.
9 9 9 9 9 4
Scan this before selectingNormal or Stand AloneMode.
Enable Light Pen/WandCommunication
Enable Keyboard WedgeEmulation
4 1 5 5 2 4
Use this option if a scanneris used in place of a lightpen.
5 1 5 5 1 4 3
Select if the scannerprovides keyboardemulation by converting thescanned bar code data tothe PC keyboard scan codeequivalent.
Enable Stand-AloneKeyboard Scanner
5 1 5 5 1 5 3
Allows the scanner to beused without an external
keyboard.
-
8/12/2019 MetroSelect Configuration Guide 02407H
54/210
Communications C 2
SECTION C COMMUNICATIONS
Load OCIA Defaults Enable OCIA Output
9 9 9 9 9 3
Scan this before selectingEnable OCIA output.
4 1 5 5 4 4
Select this option if thecommunications
requirement is an OpticallyCoupled Interface Adapter(OCIA). This is a docked(by the host) serial interface.
LoadIBM 46xx Defaults
Enable IBM 46xxCommunication
9 9 9 9 9 5
Scan this before selectingEnable IBM 46xxCommunication
4 1 5 5 0 4
Select this option for IBM46xx SIOC/RS485communications.
Not all scannerssupport this interface.The correct interfaceboard is required.
-
8/12/2019 MetroSelect Configuration Guide 02407H
55/210
Communications C 3
SECTION C COMMUNICATIONS
Load Low SpeedExternalUSB Defaults
EnableLow Speed USB
9 9 9 9 7 8
Refer to Section P forfull speed USB options.
4 1 5 5 1 1 4
Load Low SpeedInternalUSB Defaults
EnableNo Communication Mode
9 9 9 9 4 1 4 1 5 5 3 4
Select this option if thescanner does notinterfacewith the host device.
Reserved Reserved
4 1 5 5 6 4 9 1 7 5 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
56/210
-
8/12/2019 MetroSelect Configuration Guide 02407H
57/210
Scanner Operation D 1
SECTION D CONFIGURATION MODE OPTIONS
Allow Configuration Modeon Power-Up
* Allow Configuration ModeAnytime
1 1 8 1 1 7
The scanner can only enterMetroSetmode before anybar codes are scanned.
1 1 8 1 0 7
Allow MetroSetconfiguration at any time.
Allow Configuration Codeson Power Up * Allow ConfigurationCodes Anytime
1 1 8 1 1 6
Once a product bar code isscanned after power-up, thescanner will not acceptconfiguration bar codes.
1 1 8 1 0 6
Allows scanning ofconfiguration bar codes anytime.
EnableSingle Code Configuration
DisableSingle Code Configuration
1 1 8 2 1 2 1 1 8 2 0 2
-
8/12/2019 MetroSelect Configuration Guide 02407H
58/210
-
8/12/2019 MetroSelect Configuration Guide 02407H
59/210
Scanner Operation D 3
SECTION D SCAN BUFFERS
5 Scan Buffers 6 Scan Buffers
3 1 8 0 4 0
Same function as 2 Scan
Buffers, but 5 bar codes arein the scan field.
3 1 8 0 5 0
Same function as 2 Scan
Buffers, but 6 bar codes arein the scan field.
7 Scan Buffers 8 Scan Buffers
3 1 8 0 6 0
Same function as 2 ScanBuffers, but 7 bar codes arein the scan field.
3 1 8 0 7 0
Same function as 2 ScanBuffers, but 8 bar codes arein the scan field.
-
8/12/2019 MetroSelect Configuration Guide 02407H
60/210
Scanner Operation D 4
SECTION D REDUNDANT SCANS
* 0 Redundant Scans 1 Redundant Scans
3 0 1 1 0 0
Requires 1 good decode fora good scan.
3 0 1 1 1 0
Requires 2 consecutivedecodes of the same bar
code data for a good scan.
2 Redundant Scans 3 Redundant Scans
3 0 1 1 2 0
Requires 3 consecutivedecodes of the same barcode data for a good scan.
3 0 1 1 3 0
Requires 4 consecutivedecodes of the same barcode data for a good scan.
4 Redundant Scans 5 Redundant Scans
3 0 1 1 4 0
Requires 5 consecutivedecodes of the same barcode data for a good scan.
3 0 1 1 5 0
Requires 6 consecutivedecodes of the same barcode data for a good scan.
-
8/12/2019 MetroSelect Configuration Guide 02407H
61/210
Scanner Operation D 5
SECTION D REDUNDANT SCANS
6 Redundant Scans 7 Redundant Scans
3 0 1 1 6 0
Requires 7 consecutive
decodes of the same barcode data for a good scan.
3 0 1 1 7 0
Requires 8 consecutive
decodes of the same barcode data for a good scan.
In-Store Redundancy* Disable In-Store
Redundancy
1 0 1 1 1 7
Enable redundancy ofEAN-13 Sys2 & UPCA sys2& Sys4 (store printedbarcodes).
1 0 1 1 0 7
Disable redundancy ofEAN-13 Sys2 & UPCA sys2& Sys4 (store printedbarcodes).
-
8/12/2019 MetroSelect Configuration Guide 02407H
62/210
Scanner Operation D 6
SECTION D MISCELLANEOUS DECODE FEATURES
* Enable Segmented
UPC Decoding
Disable Segmented
UPC Decoding
1 0 1 1 1 3
Enabling segmented UPCdecoding aids in decipheringdamaged or incomplete barcodes.
1 0 1 1 0 3
Disable this feature whenbar codes are in goodreading condition. This willspeed up decoding andimprove over all accuracy.
* Enable
Piece In-Store Bar Codes
Disable
Piece In-Store Bar Codes
1 0 0 9 0 7
Enable piece EAN-13 Sys2,
and UPCA Sys2 and Sys4(store printed barcodes).
1 0 0 9 1 7
Disable piece EAN-13 Sys2,
and UPCA Sys2 and Sys4(store printed barcodes).
OptionalSame Symbol Check
* NormalSame Symbol Check
1 1 8 1 1 3
Requires 1 differentcharacter betweensuccessive bar codes toconsider the bar code new.
1 1 8 1 0 3
Requires 3 differentcharacters betweensuccessive bar codes toconsider the bar code new.
-
8/12/2019 MetroSelect Configuration Guide 02407H
63/210
Scanner Operation D 7
SECTION D DEPTH OF FIELD ADJUSTMENTS
Do not change these settings unless instructed by a Metrologic representative.
* Optimize forLow Density Codes
Optimize forHigh Density Codes
4 1 8 7 9 0 4 1 8 7 1 3 0
Fixed forHigh Density Codes
Fixed forMedium Density Codes
4 1 8 7 0 0 4 1 8 7 1 0
Fixed forLow Density Codes
4 1 8 7 2 0
For use withomnidirectionalscanners only.
-
8/12/2019 MetroSelect Configuration Guide 02407H
64/210
Scanner Operation D 8
SECTION D SAME SYMBOL TIME OUTS
These numbers determine the length of time before a bar code can be rescanned after it
is removed from the scan field. Single code fixed settings in msecs of No, 50, 100, 200,500, 1200 (1.2 sec), 2000 (2.0 sec) and infinite are available. User configurable valuescan be set in user-configurable increments of 50 msecs to 6350 msecs (6.35 sec).
No Same Symbol Time OutSame Symbol Time Out100 msecs
8 1 8 9 0 0 8 1 8 9 2 0
Same Symbol Time Out200 msecs
* Same Symbol Time Out500 msecs
8 1 8 9 4 0 8 1 8 9 1 0 0
Same Symbol Time Out1200 msecs
Same Symbol Time Out2000 msecs
8 1 8 9 2 4 0 8 1 8 9 4 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
65/210
Scanner Operation D 9
SECTION D SAME SYMBOL TIME OUTS
InfiniteSame Symbol Time Out
~ VariableSame Symbol Time Out
1 1 8 9 1 7
The scanner will notrepetitively scan the samebar code.
This optionoverrides thesymbol rescantime-outs.
9 1 8 9 0 0
Using the Multi-CodeMethod (on page xii), scanthis bar code and a codebyte sequence from SectionM to set the same symboltime-out duration. Valuesrange from 001 to 127(50 to 6350 msecs).
BARCODE ABSENCE
* Enable Bar CodeAbsence Detection
Disable Bar CodeAbsence Detection
1 1 8 2 0 0
Excludes the MS2000Stratos Series.
1 1 8 2 1 0
Enable Stratos Bar CodeAbsence Detection
* Disable Stratos Bar CodeAbsence Detection
1 2 4 9 1 7
The scan field must be freeof data for 50 millisecondsto accept a new bar code.
1 2 4 9 0 7
-
8/12/2019 MetroSelect Configuration Guide 02407H
66/210
Scanner Operation D 10
SECTION D LEDOPTIONS
Flash Green LED if
Rescan Allowed
* Do not flash Green LED if
Rescan Allowed
1 1 8 3 1 3
This indicates same symbol
timeout has elapsed.
1 1 8 3 0 3
Reverse LED Functions * Normal LED Functions
1 1 8 3 1 2
Red = Laser OnGreen = Good Read
1 1 8 3 0 2
Green = Laser OnRed = Good Read
* Enable 3rdLED Disable 3rdLED
1 4 3 1 0 6
Enable scanners optionalthird LED.
This feature is notavailable with allmodels.
1 4 3 1 1 6
Disable scanners optionalthird LED.
This feature is notavailable with allmodels.
-
8/12/2019 MetroSelect Configuration Guide 02407H
67/210
Scanner Operation D 11
SECTION D LEDOPTIONS
* Laser LED High Intensity Laser LED Low Intensity
2 4 3 1 0 0
Laser LED Intensity is High
or Normal.
2 4 3 1 2 0
Laser LED is Low Intensity
This feature is notavailable with allmodels.
* Scan LED High Intensity Scan LED Low Intensity
2 4 3 1 0 2
Scan LED Intensity is Highor Normal.
2 4 3 1 2 2
Scan LED Intensity is LowIntensity
This feature is not
available with allmodels.
Scan LED Off Laser LED Off
2 4 3 1 3 2
The scan LED does notsignify barcode scanning.The LED will continue tolight for all other functions.
This feature is notavailable with allmodels.
2 4 3 1 3 0
The laser LED does notsignify laser ON. The LEDwill continue to light for allother functions.
This feature is notavailable with allmodels.
-
8/12/2019 MetroSelect Configuration Guide 02407H
68/210
Scanner Operation D 12
SECTION D BEEPER OPTIONS
* Normal Tone Optional Tone 1
3 1 8 5 7 5 3 1 8 5 6 5
Optional Tone 2 Optional Tone 3
3 1 8 5 5 5 3 1 8 5 4 5
Optional Tone 4 Optional Tone 5
3 1 8 5 3 5 3 1 8 5 2 5
-
8/12/2019 MetroSelect Configuration Guide 02407H
69/210
Scanner Operation D 13
SECTION D BEEPER OPTIONS
Optional Tone 6 No Beep
3 1 8 5 1 5 3 1 8 5 0 5
* Enable Good Scan Beep Disable Good Scan Beep
1 4 1 9 0 3
Enable good scan beep onpower up.
1 4 1 9 1 3
Disable good scan beep onpower up.
* Enable ButtonBeep Controls
Disable ButtonBeep Controls
1 1 9 7 0 1
This feature is notavailable with all
models.
1 1 9 7 1 1
This feature is notavailable with all
models.
-
8/12/2019 MetroSelect Configuration Guide 02407H
70/210
Scanner Operation D 14
SECTION D BEEPER OPTIONS
Next Beep Tone Next Volume
9 9 9 9 7 5 9 9 9 9 7 4
* Loudest Volume 2ndLoudest Volume
2 1 8 5 0 0 2 1 8 5 1 0
3rdLoudest Volume No Volume
2 1 8 5 2 0 2 1 8 5 3 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
71/210
Scanner Operation D 15
SECTION D BEEPER OPTIONS
* Beep Once onSupplements Beep Twice onSupplements
1 1 8 4 0 6 1 1 8 4 1 6
Enable Fast Beep * Disable Fast Beep
1 1 8 4 1 4 1 1 8 4 0 4
-
8/12/2019 MetroSelect Configuration Guide 02407H
72/210
Scanner Operation D 16
SECTION D BEEPER OPTIONS
Beep on BEL Command * Ignore BEL Command
1 1 8 4 1 7
The scanner beeps when itreceives a BEL character
from the host. If a numberis sent within 200 msecsbefore the BEL character,then the scanner will beepthat number of times.
1 1 8 4 0 7
Enable Light Pen ToggleDuring Beep
* Disable Light Pen ToggleDuring Beep
1 1 6 9 1 3
The scanner will beep andtoggle the light pen data lineon a successful decode.This drives a good readindicator.
1 1 6 9 0 3
-
8/12/2019 MetroSelect Configuration Guide 02407H
73/210
Scanner Operation D 17
SECTION D INTER-CHARACTERDATA TRANSMISSION DELAYS
Use these codes to select the amount of delay between sending data characters andBar Code records from the scanner to the host. This helps prevent the scanner fromoverflowing host input buffers.
* 1 msecInter-Character Delay
10 msecInter-Character Delay
8 1 8 8 1 0 8 1 8 8 1 0 0
25 msec
Inter-Character Delay~ Variable msec
Inter-Character Delay
8 1 8 8 2 5 0 9 1 8 8 0 0
Scan this bar code and asequence of code bytes inSection M to set the delaybetween characters sent tothe host system. Delayrange can be set from 1 to255 msecs.Refer to the Multi-CodeConfiguration Method onpage xii.
-
8/12/2019 MetroSelect Configuration Guide 02407H
74/210
Scanner Operation D 18
SECTION D INTER-CHARACTERDATA TRANSMISSION DELAYS
No Inter-Character Delay
8 1 8 8 0 0
INTER-RECORD DATA TRANSMISSION DELAYS
~ VariableInter-Record Delay
9 1 9 3 0 0
Turn Off Laser DuringInter-Record Delay
* Leave Laser On DuringInter-Record Delay
1 1 9 3 1 7 1 1 9 3 0 7
-
8/12/2019 MetroSelect Configuration Guide 02407H
75/210
Scanner Operation D 19
SECTION D COMMUNICATION TIME OUT OPTIONS
EnableCommunications Time Outs
* Disable CommunicationsTime Outs
1 1 8 4 1 2 1 1 8 4 0 2
* Beep Before Transmit Beep After Transmit
1 1 8 4 1 3
Scanner will beep beforeeach label is transmitted.
1 1 8 4 0 3
Scanner will beep after eachlabel is transmitted.
~ Variable CommunicationsTime Out
* Default CommunicationsTime Out (2 secs)
9 1 9 1 0 0 8 1 9 1 4 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
76/210
Scanner Operation D 20
SECTION D COMMUNICATION TIME OUT OPTIONS
Short Communications Time
Out (1 sec)
Long Communications
Time Out (4 secs)
8 1 9 1 2 0 0 8 1 9 1 8 0 0
Three Beeps on Time Out * No Beeps on Time Out
1 1 8 4 1 0 1 1 8 4 0 0
Razzberry Tone onTime Out
* No Razzberry Toneon Time Out
1 1 8 4 1 1 1 1 8 4 0 1
-
8/12/2019 MetroSelect Configuration Guide 02407H
77/210
Scanner Operation D 21
SECTION D HOST SCANNER COMMANDS
Enable D/E Disable Command* Disable D/E Disable
1 1 8 0 1 5
The scanner will disable scanningafter it receives and ASCII Dfrom the host device. It willenable scanning when it receivesan ASCII E.
1 1 8 0 0 5
Do not monitor D/Ecommands.
Enable Z/R Type
D/E Simulation
* No Z/R Type
D/E Simulation
1 1 8 2 1 1
The scanner will disable scanning
after it receives an ASCII Z fromthe host device. It will enablescanning when it receives an
ASCII R.
1 1 8 2 0 1
Do not monitor Z/R
commands.
Enable F/L Laser Command* Disable F/L Laser
Command
1 1 8 0 1 4
The scanner will turn off the laserafter receiving an ASCII Fcharacter. The laser will turn onafter it receives an ASCII Lcharacter.
1 1 8 0 0 4
Do not monitor F/Lcommands.
-
8/12/2019 MetroSelect Configuration Guide 02407H
78/210
Scanner Operation D 22
SECTION D HOST SCANNER COMMANDS
Motor On/Off Using
M/O Commands
* Disable M/O
Commands
1 1 8 2 1 3
The scanner will turn the
motor OFF after it receives anASCII O character. Themotor will turn ON after thescanner receives an ASCIIM character.
For use with omnidirectionalscanners only.
1 1 8 2 0 3
Do not monitor the M/O
commands.
Enable I Command Disable I Command
1 1 5 9 1 7 1 1 5 9 0 7
Enable i Command Disable i Command
1 1 5 9 1 6 1 1 5 9 0 6
-
8/12/2019 MetroSelect Configuration Guide 02407H
79/210
Scanner Operation D 23
SECTION D HOST SCANNERCOMMANDS
Enable S Command * Disable SCommand
1 2 5 6 1 0 1 2 5 6 0 0
Enable EM Commands * Disable EM Commands
1 2 0 6 1 0
Enable EM command. Endof Medium (ctrl Y). The EMcommand sends and IDstring then a scanner statusspread over two bytes.
1 2 0 6 0 0
Enable SI/SO Command Disable SI/SO Command
1 2 5 0 1 4 1 2 5 0 0 4
-
8/12/2019 MetroSelect Configuration Guide 02407H
80/210
Scanner Operation D 24
SECTION D HOST SCANNER COMMANDS
Use
DTR Scan Disable
* Do not use
DTR Scan Disable
1 1 8 1 1 5
The scanner will monitor the
DTR input to determine ifscanning should be allowed. A+12V active level enablesdecoding. A -12V inactive leveldisables decoding.
1 1 8 1 0 5
Do not monitor the DTR
input.
Enable Pass Through Disable Pass Through
1 2 4 7 1 1
The AUX scanner mustbe configured for the
same Baud rate as thehost, with STX prefix,Nixdorf ID characters andCR Terminator enabled.
1 2 4 7 0 1
* Blink LEDs on Disable No Blink LEDs on Disable
1 2 0 4 0 2
When using CTS scan disable orDTR disable, blink the LEDs thatsignify the unit is disabled(signal = off).
1 2 0 4 1 2
When using CTS scanenable or DTR disable, donot blink the LEDs thatsignify the unit is disabled(signal = off).
-
8/12/2019 MetroSelect Configuration Guide 02407H
81/210
Scanner Operation D 25
SECTION D HOST SCANNER COMMANDS
Activate on DC2 Character* Do Not Activate on DC2
Character
1 1 8 1 1 0 1 1 8 1 0 0
Transmit NO READ ifDC2 Activated Do Not Transmit NOREAD if DC2 Activated
1 1 8 1 1 1 1 1 8 1 0 1
No Green LED DuringNO READ Xmit
* Green LED DuringNO READ Xmit
1 1 8 3 1 1 1 1 8 3 0 1
-
8/12/2019 MetroSelect Configuration Guide 02407H
82/210
Scanner Operation D 26
SECTION D POWER SAVE MODES
Always Power Save Mode No Power Save Mode
1 1 8 6 1 7
The scanner enters powersave mode immediately
after power-up and aftereach bar code scanned.
For use withomnidirectionalscanners only.
8 1 8 6 0 0
The scanner will never enterpower save mode.
Power Save Mode in1 minute
Power Save Mode in2 minutes
8 1 8 6 1 0
The scanner enters powersave mode when the
scanner remains idle for1 min.
8 1 8 6 2 0
The scanner enters powersave mode if the scanner
remains idle for 2 min.
Power Save in 5 Minutes Power Save in 10 Minutes
8 1 8 6 5 0
The scanner enters powersave mode if the scannerremains idle for 5 min.
8 1 8 6 1 0 0
The scanner enters powersave mode if the scannerremains idle for 10 min.
-
8/12/2019 MetroSelect Configuration Guide 02407H
83/210
Scanner Operation D 27
SECTION D POWER SAVE MODES
Power Save in 20 Minutes Power Save in 30 Minutes
8 1 8 6 2 0 0
The scanner enters power
save mode if the scannerremains idle for 20 min.
For use with omnidirectionalscanners only.
8 1 8 6 3 0 0
The scanner enters power
save mode if the scannerremains idle for 30 min.
DefaultPower Save Mode
BlinkPower Save Mode
3 1 9 4 0 0
This feature is notavailable with all
models.
Some Metrologic scanners
automatically wake or exitfrom the power save modeif the IR detects movement.Other Metrologic scannerswake if their multi-FunctionButton is pressed. Pleaserefer to the Installation andUsers Guide specific toeach product.
3 1 9 4 1 0
The laser Blinks OFF & ONafter a configured period of
non-use.
When the scannerrecognizes a bar code it willexit the blink mode.
This feature is notavailable with allmodels.
-
8/12/2019 MetroSelect Configuration Guide 02407H
84/210
Scanner Operation D 28
SECTION D POWER SAVE MODES
Laser OFF
Power Save Mode
Laser Motor OFF
Power Save Mode
3 1 9 4 2 0
The laser turns OFF after
a configured period ofnon-use.
This feature is notavailable with allmodels.
3 1 9 4 3 0
The laser and motor turns
OFF after a configuredperiod of non-use.
This feature is notavailable with allmodels.
Dual #1Power Save Mode
Dual #2Power Save Mode
3 1 9 4 4 0
The laser blinks OFF & ONafter a configured period ofnon-use then the laser andmotor turn OFF at thirty-minute intervals.
Example 1:Example of Dual #1 PowerSave Mode with the power
save timeout set to15 minutes.
This feature is notavailable with allmodels.
Some Metrologic scannersautomatically wake or exitfrom the power save modeif the IR detects movement.Other Metrologic scanners
wake if their multi-FunctionButton is pressed. Pleaserefer to the Installation andUsers Guide specific toeach product.
3 1 9 4 6 0
The laser turns OFF after aconfigured period of non-use then the motor turnsOFF at thirty-minuteintervals.
Example 2:Example of Dual #2 PowerSave Mode with the power
save timeout set to15-minutes.
This feature is notavailable with allmodels.
-
8/12/2019 MetroSelect Configuration Guide 02407H
85/210
Scanner Operation D 29
SECTION D POWER SAVE MODES
* EnablePower Save Switch
DisablePower Save Switch
1 1 9 7 0 0
This feature is notavailable with allmodels.
1 1 9 7 1 0
This feature is notavailable with allmodels.
EnableWake with Switch Only
* EnableWake with IR or Switch
1 1 9 7 1 7
Only wake from power saveusing the multi-functionbutton
1 1 9 7 0 7
Wake using the IR or themultifunction button.
-
8/12/2019 MetroSelect Configuration Guide 02407H
86/210
Scanner Operation D 30
SECTION D JAPANESE DOUBLE FIELD SUPPORT
To support Japanese Double Field Bar Codes, first make sure you have your scanner configured to
the following settings. Disable Segmented UPC Decoding Enable 2 scan buffers Disable bar code absence detection Enable normal code selects
Then, scan the EnableJapan 2 Fieldbar code.
Enable Japan 2 Field * Disable Japan 2 Field
1 2 4 7 1 3 1 2 4 7 0 3
Next, select the matching bar codes that are used for double field symbols.Note that only UPC/EAN bar codes are allowed in double field mode.
Select at least two characters for each bar code. The maximum is 4 upper and 4 lower bar codes.EXAMPLE
To select 54 as the first two characters in the Upper Code pair 1:1. Scan the Upper Code 1 Character 1bar code (shown on page D 31)2. Determine the correct Code Byte Value for the character 5 in 54
(Refer to Section Ms ASCII Reference Table, starting on page M 6)a. Scan Code Byte 0b. Scan Code Byte 5c. Scan Code Byte 3
3. Scan the Upper Code 1 Character 2bar code (shown on page D 31)4. Determine the correct Code Byte Value for the character 4 in 54.
a. Scan Code Byte 0b. Scan Code Byte 5c. Scan Code Byte 2
To select 18 as the first two characters in the Lower Code pair 1:1. Scan the Lower Code 1 Character 1bar code (shown on page D 31)2. Determine the correct Code Byte Value for the character 1 in 18
(refer to Section Ms ASCII Reference Table starting on page M 6)a. Scan Code Byte 0b. Scan Code Byte 4c. Scan Code Byte 9
3. Scan the Lower Code 1 Character 2bar code (shown on page D 31)4. Determine the correct Code Byte Value for the character 8 in 18.
(Refer to Section Ms ASCII Reference Table, starting on page M 6)a. Scan Code Byte 0b. Scan Code Byte 5c. Scan Code Byte 6
-
8/12/2019 MetroSelect Configuration Guide 02407H
87/210
Scanner Operation D 31
SECTION D JAPANESE DOUBLE FIELD SUPPORT
Upper Code 1 Character 1 Upper Code 1 Character 2
9 3 0 0 0 0 9 3 0 1 0 0
Lower Code 1 Character 1 Lower Code 1 Character 2
9 3 0 2 0 0 9 3 0 3 0 0
Upper Code 2 Character 1 Upper Code 2 Character 2
9 3 0 4 0 0 9 3 0 5 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
88/210
Scanner Operation D 32
SECTION D JAPANESE DOUBLE FIELD SUPPORT
Lower Code 2 Character 1 Lower Code 2 Character 2
9 3 0 6 0 0 9 3 0 7 0 0
Upper Code 3 Character 1 Upper Code 3 Character 2
9 3 0 8 0 0 9 3 0 9 0 0
Lower Code 3 Character 1 Lower Code 3 Character 1
9 3 1 0 0 0 9 3 1 1 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
89/210
Scanner Operation D 33
SECTION D JAPANESE DOUBLE FIELD SUPPORT
Upper Code 4 Character 1 Upper Code 4 Character 2
9 3 1 2 0 0 9 3 1 3 0 0
Lower Code 4 Character 1 Lower Code 4 Character 2
9 3 1 4 0 0 9 3 1 5 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
90/210
Scanner Operation D 34
SECTION D JAPANESE DOUBLE FIELD SUPPORT
Japanese Trial Time Enable Code Selects
9 3 8 8 0 0
Scan the above bar code followed bythe 3 code bytes in Section M that
represent the timeout value desired if inspecial code select mode.
1 is equal to 100 milliseconds
Example:If a 500 millisecond timeout is desired,scan the above code followed by codebyte 0, code byte 0 and code byte 5.
1 1 8 2 1 7
Transmit Top Code Select* Transmit
All Code Selects
1 2 0 4 1 0
Transmit the highest priority code selectif all are not found.
1 2 0 4 0 0
Transmit all code selects.
Enable Error Tone * Disable Error Tone
1 1 8 5 1 3
Adds ability to sound RAZZ error tonewhen special code selects fail.
1 1 8 5 0 3
-
8/12/2019 MetroSelect Configuration Guide 02407H
91/210
Scanner Operation D 35
SECTION D TEST MODES
Scanability ON * Scanability OFF
1 1 8 0 1 7
The scanner will enter
scanability test mode.
Do not enableunless instructed toby a Metrologicrepresentative.
1 1 8 0 0 7
Scan Count Mode ON * Scan Count Mode OFF
1 1 8 0 1 6
The scanner will enter scancount test mode and the
scanners firmware numberwill transmit to the host.
Do not enableunless instructed toby a Metrologicrepresentative.
1 1 8 0 0 6
Temporary Symbologies
The Temporary Symbologiestest
code enables all major types of barcode symbologies, reduces theminimum number of charactersrequired to 1, sets the minimum ITFcharacters required to 2, and addsthe symbology name as a prefix tothe transmission. This feature isdisabled when power to thescanner is cycled OFFand ON.
9 9 8 0 4 1
Do not enableunless instructed toby a Metrologicrepresentative
-
8/12/2019 MetroSelect Configuration Guide 02407H
92/210
-
8/12/2019 MetroSelect Configuration Guide 02407H
93/210
Prefixes/Suffixes E 1
SECTION E CONFIGURABLE PREFIXES,ALL DATA
Scan the Enter/Exit Configuration Modebar code before trying to set thisfeature. Please refer to the Multi-Code method on page xii.
Enter/ExitConfiguration Mode
~ Configurable PrefixCharacter #1
9 9 9 9 9 9 9 0 3 5 0 0
A prefix ID can be addedand assigned for datatransmission. Use this codewith a 3-code bytesequence from Section Mthat represents the desiredcharacter.
~ Configurable PrefixCharacter #2
~ Configurable PrefixCharacter #3
9 0 3 6 0 0
Assigns a 2ndconfigurableprefix character.
9 0 3 7 0 0
Assigns a 3rdconfigurableprefix character.
~ Configurable PrefixCharacter #4 ~ Configurable PrefixCharacter #5
9 0 3 8 0 0
Assigns a 4thconfigurable
prefix character.
9 0 3 9 0 0
Assigns a 5thconfigurable
prefix character.
-
8/12/2019 MetroSelect Configuration Guide 02407H
94/210
Prefixes/Suffixes E 2
SECTION E CONFIGURABLE PREFIXES,ALL DATA
~ Configurable Prefix
Character #6
~ Configurable Prefix
Character #7
9 0 4 0 0 0
Assigns a 6thconfigurable
prefix character.
9 0 4 1 0 0
Assigns a 7thconfigurable
prefix character.
~ Configurable PrefixCharacter #8
~ Configurable PrefixCharacter #9
9 0 4 2 0 0
Assigns a 8thconfigurableprefix character.
9 0 4 3 0 0
Assigns a 9thconfigurableprefix character.
~ Configurable PrefixCharacter #10
* Clear all UserConfigurable Prefixes
9 0 4 4 0 0
9 9 9 9 8 5
-
8/12/2019 MetroSelect Configuration Guide 02407H
95/210
Prefixes/Suffixes E 3
SECTION E CONFIGURABLE IDCHARACTERS,CODE SPECIFIC
* Use Configurable CodeID Bytes as Prefixes
Use Configurable Code IDBytes as Suffixes
1 0 5 5 0 7
User configured, codespecific ID bytes aretransmitted before the data.
If using prefixes, userconfigured suffixescan not be used.
1 0 5 5 1 7
User configured, codespecific ID bytes aretransmitted after the data.
If using suffixes, userconfigured prefixescan not be used.
IDENTIFIERS CHARACTER
~ Configurable UPC-A ID ~ Configurable UPC-E ID
9 0 5 6 0 0 9 0 5 7 0 0
While using the Multi-Code method, scan this bar code followed by the 3 code byte barcodes in Section M that represent a unique ID character to be associated with this bar codetype. (Refer to the Multi-Code Method on page xii.)
-
8/12/2019 MetroSelect Configuration Guide 02407H
96/210
Prefixes/Suffixes E 4
SECTION E CONFIGURABLE IDCHARACTERS,CODE SPECIFIC
~ Configurable EAN-8 ID ~ Configurable EAN-13 ID
9 0 5 8 0 0
While using the Multi-Code method,scan this bar code followed by the 3code byte bar codes in Section Mthat represent a unique ID characterto be associated with this bar codetype. (Refer to the Multi-CodeMethod on page xii.)
9 0 5 9 0 0
~ Configurable Code 39 ID ~ ConfigurableCode 128 ID
9 0 6 0 0 0 9 0 6 1 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
97/210
Prefixes/Suffixes E 5
SECTION E CONFIGURABLE IDCHARACTERS,CODE SPECIFIC
~ Configurable Code 93 ID ~ Configurable Code 11 ID
9 0 6 3 0 0
While using the Multi-Code method,scan this bar code followed by the 3code byte bar codes in Section Mthat represent a unique ID characterto be associated with this bar codetype. (Refer to the Multi-CodeMethodon page xii.)
9 0 6 4 0 0
~ Configurable Telepen ID ~ Configurable
TRI-OPTIC ID
9 0 6 2 0 0 9 0 7 2 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
98/210
Prefixes/Suffixes E 6
SECTION E CONFIGURABLE IDCHARACTERS,CODE SPECIFIC
~ Configurable
Standard 2 of 5 ID
~ Configurable
Interleaved 2 of 5 ID
9 0 7 1 0 0
While using the Multi-Code method,scan this bar code followed by the 3code byte bar codes in Section Mthat represent a unique ID characterto be associated with this bar codetype. (Refer to the Multi-CodeMethod on page xii.)
9 0 6 7 0 0
~ ConfigurableMatrix 2 of 5 ID ~ ConfigurableAirline 2 of 5 ID
9 0 6 8 0 0 9 0 6 9 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
99/210
Prefixes/Suffixes E 7
SECTION E CONFIGURABLE IDCHARACTERS CODE SPECIFIC
~ ConfigurableMSI Plessey ID
~ ConfigurableUK Plessey ID
9 0 6 5 0 0
While using the Multi-Code method,scan this bar code followed by the 3code byte bar codes in Section Mthat represent a unique ID characterto be associated with this bar codetype. (Refer to the Multi-CodeMethod on page xii.)
9 0 7 0 0 0
~ ConfigurableCodabar ID
* Clear all ConfigurableCode Specific IDs
9 0 6 6 0 0 9 9 9 9 8 3
-
8/12/2019 MetroSelect Configuration Guide 02407H
100/210
Prefixes/Suffixes E 8
SECTION E STANDARD PREFIX CHARACTERS
Enable STX Prefix * Disable STX Prefix
1 1 6 6 1 5
The scanner will transmit aStart of TeXt (ASCII 02H)
before each bar code.
1 1 6 6 0 5
Will not transmit a Start ofTeXt (ASCII 02H) before
each bar code.
EnableRockford-Thompson Mode
* Disable Rockford-Thompson Mode
1 0 5 5 1 3 1 0 5 5 0 3
Enable AIM ID Characters* Disable AIM ID
Characters
1 0 7 9 1 5
The scanner will transmitAIM symbology identifiers.
Some scannermodels may notsupport this feature.
1 0 7 9 0 5
The scanner will nottransmit AIM symbologyidentifiers.
-
8/12/2019 MetroSelect Configuration Guide 02407H
101/210
Prefixes/Suffixes E 9
SECTION E STANDARD PREFIX CHARACTERS
Enable UPC Prefix ID * Disable UPC Prefix ID
1 1 6 6 1 7
When enabled, the scanner
will transmit a prefix beforeany UPC/EAN bar code.
The prefixes are as follows:A (UPC-A),E0 (UPC-E),F (EAN-13), andFF (EAN-8).
1 1 6 6 0 7
Do not send prefix ID
Characters with UPC/EANcodes.
Enable NCR Prefix ID * Disable NCR Prefix ID
1 0 7 9 1 1
When enabled, the scannerwill transmit a prefix beforethe following code types.
The prefixes are as follows:
1 0 7 9 0 1
A (UPC-A),E0 (UPC-E),FF (EAN-8),F (EAN-13),B1 (Code 39),B2 (ITF) andB3 (Code 128 & other codes).
-
8/12/2019 MetroSelect Configuration Guide 02407H
102/210
Prefixes/Suffixes E 10
SECTION E STANDARD PREFIX CHARACTERS
Enable Nixdorf ID
Characters
* Disable Nixdorf ID
Characters
1 0 7 9 1 7
This option transmits code
identifiers before each barcode for manySiemens/Nixdorf registers.
1 0 7 9 0 7
This option will not transmit
Siemens/Nixdorf codeidentifiers.
Enable SANYO IDCharacters
* Disable SANYO IDCharacters
1 0 7 9 1 6
Transmit Sanyo IDCharacters.
1 0 7 9 0 6
Do not transmit Sanyo IDCharacters.
-
8/12/2019 MetroSelect Configuration Guide 02407H
103/210
Prefixes/Suffixes E 11
SECTION E STANDARD PREFIX CHARACTERS
Enable TEC RegisterFormat ID Characters
Disable TEC RegisterFormat ID Characters
1 2 4 7 1 0 1 2 4 7 0 0
Enable TEC MA1530ID Characters
Disable TEC MA1530ID Characters
1 0 8 0 1 0 1 0 8 0 0 0
Enable Symbology Prefix Disable Symbology Prefix
1 0 5 5 1 4
This option adds asymbology description infront of the bar codetransmission.
1 0 5 5 0 4
Do not add a symbologydescription in front of the barcode transmission.
-
8/12/2019 MetroSelect Configuration Guide 02407H
104/210
Prefixes/Suffixes E 12
SECTION E STANDARD PREFIX CHARACTERS
Enable Manufacturer
ID Prefix
* Disable Manufacturer
ID Prefix
1 0 5 5 1 2
Transmits METROLOGIC
before all bar code data toidentify the scanner as aMetrologic Scanner.
1 0 5 5 0 2
The scanner will not
transmit the manufactureridentification string.
Enable C Prefix * Disable C Prefix
1 0 5 5 1 1 1 0 5 5 0 1
Enable $ Prefix ID
for UPC/EAN
* Disable $ Prefix ID
for UPC/EAN
1 0 5 5 1 0 1 0 5 5 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
105/210
Prefixes/Suffixes E 13
SECTION E STANDARD PREFIX CHARACTERS
Enable Tab Prefix * Disable Tab Prefix
1 1 6 6 1 1
The scanner will transmit a
TAB (ASCII 09H) beforeeach bar code.
1 1 6 6 0 1
The scanner will not
transmit a TAB.
Enable SNI Beetle Mode * Disable SNI Beetle Mode
1 1 6 1 1 1 1 1 6 1 0 1
Enable Cipher 1021 IDs * Disable Cipher 1021 IDs
1 1 6 1 1 3 1 1 6 1 0 3
-
8/12/2019 MetroSelect Configuration Guide 02407H
106/210
Prefixes/Suffixes E 14
SECTION E STANDARD SUFFIX CHARACTERS
* Enable CR Suffix Disable CR Suffix
1 1 6 6 1 3
The scanner will transmit aCarriage Return after each
bar code.
1 1 6 6 0 3
The scanner will nottransmit a Carriage Return
after each bar code.
* Enable LF Suffix Disable LF Suffix
1 1 6 6 1 2
The scanner will transmit aLine Feed after each barcode.
This feature isDisabled whenkeyboard wedgedefaults are loaded.
1 1 6 6 0 2
The scanner will nottransmit a Line Feed aftereach bar code.
Enable Tab Suffix * Disable Tab Suffix
1 1 6 6 1 0
The scanner will transmit aTAB (ASCII 09H) after eachbar code.
1 1 6 6 0 0
The scanner will nottransmit a TAB (ASCII 09H)after each bar code.
-
8/12/2019 MetroSelect Configuration Guide 02407H
107/210
Prefixes/Suffixes E 15
SECTION E STANDARD SUFFIX CHARACTERS
Enable ETX Suffix * Disable ETX Suffix
1 1 6 6 1 4
The scanner will transmit
End of TeXt (ASCII 03H)after the bar code data.
1 1 6 6 0 4
The scanner will not
transmit End of TeXt(ASCII 03H).
Enable UPC Suffix ID * Disable UPC Suffix ID
1 1 6 6 1 6
The scanner will transmit asuffix after any UPC/EANbar code.
The suffixes are as follows:A (UPC-A),E (UPC-E),F (EAN-13) and
F (EAN-8).
1 1 6 6 0 6
The scanner will nottransmit a suffix afterUPC/EAN bar codes.
-
8/12/2019 MetroSelect Configuration Guide 02407H
108/210
Prefixes/Suffixes E 16
SECTION E LONGITUDINAL REDUNDANCY CHECK (LRC)
Enable Transmit of
LRC Calculation
* Disable Transmit of
LCR Calculation
1 0 7 8 1 1
The scanner outputs an
LRC check character afterthe bar code.
1 0 7 8 0 1
The scanner will not output
an LRC (check character)after the bar code.
* Start LRC on First Byte Start LRC on Second Byte
1 0 7 8 0 0
The scanner will calculatethe LRC check digit startingwith the first character.
1 0 7 8 1 0
The scanner will calculatethe LRC check digit startingwith the second character.
-
8/12/2019 MetroSelect Configuration Guide 02407H
109/210
Prefixes/Suffixes E 17
SECTION E CONFIGURABLE SUFFIXES,ALL DATA
Scan the Enter/Exit Configuration Mode bar code before trying to set this feature.Refer to the Multi-Code Method on page xii.
Enter/ExitConfiguration Mode
~ Configurable SuffixCharacter #1
9 9 9 9 9 9 9 0 4 5 0 0
A suffix ID can be addedand assigned for datatransmission. Use this codewith a 3 code byte sequencefrom Section M thatrepresents the desiredcharacter.
~ Configurable Suffix
Character #2
~ Configurable Suffix
Character #3
9 0 4 6 0 0
Assigns a 2ndconfigurablesuffix character.
9 0 4 7 0 0
Assigns a 3rdconfigurablesuffix character.
-
8/12/2019 MetroSelect Configuration Guide 02407H
110/210
Prefixes/Suffixes E 18
SECTION E CONFIGURABLE SUFFIXES,ALL DATA
~ Configurable Suffix
Character #4
~ Configurable Suffix
Character #5
9 0 4 8 0 0
Assigns a 4thconfigurable
suffix character.
While using the Multi-Code method,scan this bar code followed by the 3code byte bar codes in Section Mthat represents the desiredcharacter. (Refer to the Multi-CodeMethod on page xii.)
9 0 4 9 0 0
Assigns a 5thconfigurable
suffix character.
~ Configurable SuffixCharacter #6
~ Configurable SuffixCharacter #7
9 0 5 0 0 0
Assigns a 6thconfigurablesuffix character.
9 0 5 1 0 0
Assigns 7thconfigurablesuffix character.
-
8/12/2019 MetroSelect Configuration Guide 02407H
111/210
Prefixes/Suffixes E 19
SECTION E CONFIGURABLE SUFFIXES,ALL DATA
~ Configurable SuffixCharacter #8
~ Configurable SuffixCharacter #9
9 0 5 2 0 0
Assigns a 8thconfigurablesuffix character.
9 0 5 3 0 0
Assigns a 9thconfigurablesuffix character.
~ Configurable SuffixCharacter #10
9 0 5 4 0 0
Assigns a 10thconfigurablesuffix character.
While using the Multi-Code method, scan thisbar code followed by the3 code byte bar codes inSection M that representthe desired character.
(Refer to the Multi-CodeMethod on page xii.)
* Clear All UserConfigurable Suffixes
9 9 9 9 8 4
-
8/12/2019 MetroSelect Configuration Guide 02407H
112/210
Prefixes/Suffixes E 20
SECTION E SPECIAL FORMATS
Enable SINEKO Mode * Disable SINEKO Mode
1 0 7 9 1 4 1 0 7 9 0 4
Enable Newcode FormattingMode A
* Disable NewcodeFormatting Mode A
1 1 6 7 1 1 1 1 6 7 0 1
Enable Newcode Formatting
Mode B
* Disable Newcode
Formatting Mode B
1 1 6 7 1 0 1 1 6 7 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
113/210
Prefixes/Suffixes E 21
SECTIONE CHARACTER REPLACEMENTS
To replace a character:1. Scan the Enter/Exit Configuration Modebar code
(located on page xii, at the front of this guide).
2. Scan the Character to Replace Code (shown below).
3. Scan the ASCII Code Byte value of the character you wish to replace
(refer to the ASCII reference table in Section M).
4. Scan the Replacement Characterbar code.
5. Scan the ASCII Code Byte value of the replacement character.
6. Scan the Enter/Exit Configuration Modebar code
(located on page xii, at the front of this guide).
Character to Replace No Replacement
9 3 8 6 0 0 8 3 8 6 0 0
Replacement Character
9 3 8 7 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
114/210
-
8/12/2019 MetroSelect Configuration Guide 02407H
115/210
Code Formatting F 1
SECTION F UPC/EAN
* Transmit UPC-ACheck Digit
Do not TransmitUPC-A Check Digit
1 0 7 5 1 7 1 0 7 5 0 7
Transmit UPC-E
Check Digit
* Do Not Transmit
UPC-E Check Digit
1 0 7 5 1 6 1 0 7 5 0 6
Expand UPC-E to 12 Digits* Do Not Expand
UPC-E To 12 Digits
1 0 7 5 1 5
Expand UPC-E bar codes tothe 12 digit equivalent,
UPC-A bar codes.
1 0 7 5 0 5
Do not expand UPC-E to the12 digit equivalent, UPC-A
bar code.
-
8/12/2019 MetroSelect Configuration Guide 02407H
116/210
Code Formatting F 2
SECTION F UPC/EAN
Convert UPC-A to EAN-13
* Do Not Convert
UPC-A to EAN-13
1 0 7 5 1 4
The scanner converts
UPC-A to EAN-13 bytransmitting a leading zerobefore the bar code.
1 0 7 5 0 4
The scanner will not convert
UPC-A to EAN-13.
Transmit Lead Zeroon UPC-E
Do Not TransmitLead Zero on UPC-E
1 0 7 5 1 3
This option will transmit azero before each
UPC-E bar code.
1 0 7 5 0 3
This option will not transmita zero before each UPC-E
bar code.
Convert EAN-8 to EAN-13* Do Not Convert
EAN-8 to EAN-13
1 0 7 5 1 2
The scanner will transmitfive zeros before the barcode to convert EAN-8 toEAN-13.
1 0 7 5 0 2
The scanner will not convertEAN-8 to EAN-13.
-
8/12/2019 MetroSelect Configuration Guide 02407H
117/210
Code Formatting F 3
SECTION F UPC/EAN
* Transmit UPC-ANumber System
Do Not Transmit UPC-ANumber System
1 0 7 5 1 1 1 0 7 5 0 1
Metrologic stronglydiscourages usingthis feature.Duplicate numbersmay result in thedatabase.
* TransmitUPC-A MFR #
Do Not TransmitUPC-A MFR #
1 0 7 6 1 1 1 0 7 6 0 1
* TransmitUPC-A ITEM #
Do Not TransmitUPC-A ITEM #
1 0 7 6 1 0 1 0 7 6 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
118/210
Code Formatting F 4
SECTION F UPC/EAN
* Transmit EAN-8
Check Digit
Do Not Transmit
EAN-8 Check Digit
1 0 7 9 1 0 1 0 7 9 0 0
* Transmit EAN-13Check Digit Do Not TransmitEAN-13 Check Digit
1 0 7 9 1 2 1 0 7 9 0 2
GTIN-14 Format No GTIN-14 Format
1 0 7 5 1 0
This feature is notavailable with all
models.
1 0 7 5 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
119/210
Code Formatting F 5
SECTION F CODABAR
Transmit Codabar Start/StopCharacters
* Do Not Transmit CodabarStart/Stop
1 0 7 7 1 7
Transmits Codabars start/stopcharacters before and after eachbar code.
1 0 7 7 0 7
Will not transmit Codabarsstart/stop characters before andafter each bar code.
Convert Codabar Start/Stop
Characters to Lowercase
* Do Not Convert CodabarStart/Stop Characters toLowercase
1 1 5 1 1 0 1 1 5 1 0 0
-
8/12/2019 MetroSelect Configuration Guide 02407H
120/210
Code Formatting F 6
SECTIONF CODABAR
Enable
CLSI Editing
1 0 7 7 1 6
CLSI type editing will be done
before the information istransmitted to the host.
This option will onlywork with 14 digitCodabar type lengths.
* Do Not EnableCLSI Editing
1 0 7 7 0 6
This option will not performCLSI type editing before theinformation is transmitted tothe host.
-
8/12/2019 MetroSelect Configuration Guide 02407H
121/210
Code Formatting F 7
SECTION F CODE 39
Enable MOD 43Check on Code 39
* Disable MOD 43 Checkon Code 39
1 0 0 2 1 3
The scanner will only scanCode 39 bar codes thathave a valid Modulo 43Check Digit.
1 0 0 2 0 3
The scanner will not testCode 39 bar codes for aModulo 43 Check Digit.
Transmit Mod 43
Check Digit on Code 39*