minimum and general data sets

7/30/2019 Minimum and General Data Sets

1/4

PCP-R IFTS Min&GenDataSets.DRAFT.20050901.Posted.xls General & Minimum Data Sets (8/4/2011) C-FER Technologies

PCP-RIFTS: General Data Set

PCP-RIFTS: Min imum Data Set (1)

Parameter DescriptionCompany Name Name of operating company (Participant)

Division Name Name of operating unit, group of field, etc.

Field Name Name of oil field

Field Location (Country) Name of country field is in

Location of PCP Supply Centre Country, Provinces/State, and nearest Town/City of source of PCP system. If more than one supply centre, pleaprovide location of main supply centre.

Location of PCP Teardown Facility Country, Province/State, and nearest Town/City where pulled PCPs are sent for teardown and inspection. If mothan one teardown facility, please provide location of main teardown facility.

Field Type (Onshore/Offshore)Onshore, Offshore (Platform), Offshore (Subsea), Onshore/Offshore

Oil Density at STP Oil density inAPI at standard temperature (15C) and pressure (1 atm)

Reservoir Temperature Fluid temperature at the reservoir conditions

Dead Oil Viscosity at STP Dead oil viscosity at standard temperature (15C) and pressure (1 atm)

Oil Bubble Point Pressure Bubble point (vapour) pressure of oil at Reservoir Temperature

Well Name Name or identifier of well

Well Type (Geometry) Vertical, Slant, Deviated, Horizontal, S idetracked, Re-Entry Sidetrack, or Multilateral

Wellhead location Onshore, Platform, Subsea

Pad or Platform Name Name of group of wells

Reservoir Name/Zone Name(s) of producing reservoirs (during production period)

Reservoir Type Carbonate, Consolidated Sandstone, Unconsolidated Sandstone, Evaporite

Reservoir Recovery Mechanism Aquifer drive, Solution Gas Drive, Water flood, EOR (e.g., CO2 flooding, Water-Alternating-Gas (WAG), PolymeFlood, Steam stimulation, etc)

Completion Type Perforated Casing, Open hole, or Unknown

Sand Control Type Type of sand control installed in the well during the production period, e.g. Gravel Pack, Slotted Liner, Wire-wrapped Screen, etc. If no sand control installed, please indicate None.

Production Casing Outer Diameter Nominal outer diameter of the production casing

Production Period Number Production period number for well

Date Installed (mm/dd/yyyy) Date PCP system was installed

Date Period Started (mm/dd/yyyy) Date PCP system was first started. If not provided, the Date Period Started will be assumed equal to the DateInstalled.

Period Status Status of the production period: Period Completed or Still on Production.

Date Period Ended (mm/dd/yyyy) Date PCP system failed, was shutdown, or last date record was updated if PCP still running. If not provided, theDate Period Ended will be assumed equal to the Date Pulled.

Date Pulled (mm/dd/yyyy) Date PCP system was pulled

Actual Runtime Days the PCP system was actually running. If not provided, Actual Runtime will be assumed equal to Duration

PCP System Failed? Did/has the PCP system failed (Yes or No)? This parameter should be consistent with the Period Status. If PerioFailure Information

Field Information

Fluid Information

Well Information

Runtime Data

(dates)

Status ="Still Running", then PCP System Failed? should be "No". If PCP System Failed? ="Yes", then Period

Status should be "Period Completed".

Reason for Pull: General General category of why the PCP was pulled

Reason for Pull: Specific More specific reason why the PCP was pulled

Primary Failed System Only required if both PCP and Tubing System failed. If only one system fails, then the Primary Failed System isdefaulted to that system.

PCP System - Primary Failed Item The primary failed PCP component or partPCP System - Primary Failure Descriptor The primary descriptor of the PCP System - Primary Failed Item

PCP System - Secondary Failure Descriptor The secondary descriptor of the PCP System - Primary Failed Item

PCP System - Failure Cause: General Circumstances during design, manufacture or use that led to the PCP System failure

PCP System - Failure Cause: Specific Specific circumstances during design, manufacture or use that led to the PCP System failure

PCP System - Contributing Cause: General Circumstances during design, manufacture or use that contributed to the PCP System failure

PCP System - Contributing Cause: Specific Specific circumstances during design, manufacture or use that contributed to the PCP System failure

Tubing System Failed? Did/has the Tubing System failed?

Tubing System - Primary Failed Item The primary failed Tubing component or part

Tubing System - Primary Failure Descriptor The primary descriptor of the Tubing System - Primary Failed Item

Tubing System - Secondary Failure Descriptor The secondary descriptor of the Tubing System - Primary Failed Item

Tubing System - Failure Cause: General Circumstances during design, manufacture or use that led to the Tubing System failure

Tubing System - Failure Cause: Specific Specific circumstances during design, manufacture or use that led to the Tubing System failure

Tubing System - Contributing Cause: General Circumstances during design, manufacture or use that contributed to the Tubing System failure

Tubing System - Contributing Cause: Specific Specific circumstances during design, manufacture or use that contributed to the Tubing System failure

Failure Comments Specific notes regarding the failure. Include a description of the "contaminant" (e.g., sand, scale, asphaltene, etcthe Contaminated failure descriptor is used.

Control Panel Type Type of control panel: Switchboard, Switchboard with Soft Start, Variable Frequency Drive

Control Panel Vendor Vendor of control panel

Power Transmission Type Type of power transmission: Belts and Sheaves, Gears, Combination, or Other

Prime Mover Type Type of prime mover: Electric Motor, Internal Combustion Engine, or Hydraulic Motor.

Drivehead Vendor Name of vendor/manufacturer of surface drivehead

Prime Mover Rated Power Rated power of prime mover on surface drive

Power Source Local Power Line/Grid, Field Generator, Wellsite Generator

Power Quality Excellent, Good, Average, Low, Poor

(as per PCP

Failure

Nomenclature

Standard)

Surface

Equipment Data

IF Rod Driven PCP

System

Confidential 1 / 4


2/4




Parameter Description

PCP Vendor Name of vendor/manufacturer of pump components (e.g., Weatherford BMW). If rotor vendor and stator vendordifferent, use the stator vendor as the Pump Vendor.

Pump Model (SI) Catalogue model designation of pump (e.g., 15-1400)

Elastomer Model Model designation of stator elastomer

Elastomer Type Type of stator elastomer (e.g., medium nitrile, high nitrile, fluroelastomer, etc.)

Rotor Coating Type Type of rotor coating (e.g. chrome, boron, etc.)

Pump Rated Displacement Rated displacement of the pump

Pump Rated Differential Pressure Rated differential pressure of the pump

Stator Serial Number Serial number or unique identifiers for that specific PCP statorRotor Serial Number Serial number or unique identifiers for that specific PC P rotor

In-Test: Date Date pump was bench tested prior to installation

In-Test: Speed Rotational speed pump was bench tested at (RPM) prior to installation

In-Test: Reference Differential Pressure Reference pressure of bench test volumetric efficiency (usually rated pressure) prior to installation

In-Test: Volumetric Efficiency at Reference DP Volumetric efficiency of pump at reference pressure and test speed prior to installation

In-Test: Friction Torque Friction torque of pump at test speed prior to installation

In-Test: Volumetric Efficiency at Zero DP Volumetric efficiency of pump at zero differential pressure prior to installation

Out-Test: Date Date pump was bench tested after pull

Out-Test: Speed Rotational speed pump was bench tested at (RPM) after pull

Out-Test: Reference Differential Pressure Reference pressure of bench test volumetric efficiency (usually rated pressure) after pull

Out-Test: Volumetric Efficiency at Reference

DP

Volumetric efficiency of pump at reference pressure and test speed after pull

Out-Test: Friction Torque Friction torque of pump at test speed after pull

Out-Test: Volumetric Efficiency at Zero DP Volumetric efficiency of pump at zero differential pressure after pull

Date Pump Inspected Date pump was inspectedStator New/Used/Repaired When installed, was the stator New or Used (without service or minor servicing only)

Rotor New/Used/Rechromed When installed, was the rotor New, Used (without service or minor servicing only), Repaired (used and servicedRechromed

Stator Pull Condition Condition of stator when pulled: Reusable or Not Reusable

Rotor Pull Condition Condition of rotor when pulled: Reusable or Not Reusable

Pump Intake Vendor Name of vendor/manufacturer of pump intake

Pump Intake TypeType of pump intake: None (PCP Opening), Tail Pipe, Standard Bolt-on Intake (Flexshaft), Static Gas Separator

Bottom-Feeder Gas Separator, Multiple Stator Intakes, Rotary Gas Separator, or Gas Handler

Pump Intake Pull Condition Condition of pump intake when pulled: Reusable or Not Reusable

Tag Bar Type Type of pump tag bar (e.g., integral bar or plate or separate downhole component)

Downhole

Equipment Data

Tag Bar Pull Condition Condition of tag bar when pulled: Reusable or Not Reusable

Pump Seating Depth MD Measured depth of the pump intake

Pump Seating Depth TVD Vertical depth of the pump intake

Inclination at PSD Inclination (hole angle) at the Pump Seating Depth

Maximum Dogleg Maximum curvature that the PCP had to pass through during installation

Tubing Outer Diameter Nominal outer diameter of production tubing

Tubing Weight Weight of the production tubing

Tubing Internal Coating Type Coating type on ID of production tubing string, if tubing ID is coated

Rod Diameter Nominal diameter of rod string

Rod Material Grade Material grade of rod string

Rod Type Type of rod string: Standard, Continuous, or Hollow

Rod Centralizer Type Type of rod string coupling centralizers, if used (Coated, Spin Thru)

Rod Guide Type Type of rod string rod body guides, if used

Tubing Anchor Installed? Was a device installed to anchor the tubing to the casing?

Tubing Anchor Model Model designation of torque anchor. Alternatively, torque anchor vendor may be provided.

Tubing Rotator Installed? Was a device installed to rotate the tubing?

Tubing Rotator Vendor Name of vendor/manufacturer of tubing rotator components

Tubing Rotator Model Model designation of tubing rotator

Gearbox Vendor Name of vendor/manufacturer of gearbox

Gearbox Model Catalogue model designation of gearbox

Gearbox Gear Ratio Gear ratio of gearbox (e.g., 9:1)

Gearbox Trim Metallurgy, elastomers and coatings

Gearbox Serial Number(s) Serial number(s) or unique identifiers for that specific gearbox

Gearbox New/Used/Repaired When installed, was the gearbox New, Used (without service or minor servicing only), or Repaired (used andserviced)

Gearbox Pull Condition Condition of downhole gearbox when pulled: Reusable or Not Reusable

Seal Vendor Name of vendor/manufacturer of seal components

Seal Model Catalogue model designation of seal (e.g. LSBSB-HL)

Seal Trim Metallurgy, elastomers and coatings

Seal Serial Number(s) Serial number(s) or unique identifiers for that specific seal

Seal New/Used/Repaired When installed, was the seal New, Used (without service or minor servicing only), or Repaired (used and service

Seal Pull Condition Condition of downhole seal when pulled: Reusable or Not Reusable

Motor Vendor Name of vendor/manufacturer of motor

Motor Model Catalogue model designation of motor (e.g. KMH)

Motor Rated Power @ 60Hz Rated horsepower of motor at 60 Hz

Motor Trim Metallurgy, elastomers and coatings

Motor Serial Number(s) Serial number(s) or unique identifiers for that specific motor

IF DH Drive PCP

System

IF Rod Driven PCP

System

Confidential 2 / 4


3/4





Motor New/Used/Repaired When installed, was the motor New, Used (without service or minor servicing only), or Repaired (used andserviced)

Motor Pull Condition Condition of downhole motor when pulled: Reusable or Not Reusable

Flexshaft Vendor Name of vendor/manufacturer of flexshaft components

Flexshaft Model Catalogue model designation of flexshaft

Flexshaft Trim Metallurgy, elastomers and coatings

Flexshaft Serial Number(s) Serial number(s) or unique identifiers for that specific flexshaft

Flexshaft New/Used/Repaired When installed, was the flexshaft New, Used (without service or minor servicing only), or Repaired (used and

serviced)Flexshaft Pull Condition Condition of flexshaft when pulled: Reusable or Not Reusable

Cable Vendor Name of vendor/manufacturer of cable

Cable Model Catalogue model designation of cable (e.g., Redalead or CELF)

Cable Size American Wire Gauge (AWG) size of the cable

Cable Armour Galvanized, Monel, Stainless Steel, etc.

Cable Serial Number(s) Serial number(s) or unique identifiers for that specific cable

Motor Lead Extension (MLE) Model Model designation of motor lead extension (MLE)

Cable New/Used/RepairedWhen installed, was the cable New, Used (without service or minor servicing only), or Repaired (used and servic

Cable System Pull Condition Condition of cable system when pulled: Reusable or Not Reusable

Wellhead Penetrator Model Model designation of wellhead penetrator. Alternatively, wellhead penetrator vendor may be provided.

Packer Penetrator Model Model designation of packer penetrator. Alternatively, packer penetrator vendor may be provided.

Downhole Monitoring System Installed?

Downhole Monitoring System Vendor Was a downhole monitoring system installed with the PCP system? (Yes/No)

Downhole Monitoring System

New/Used/Repaired

When installed, was the downhole monitoring system New, Used (without service or minor servicing only), or

Repaired (used and serviced)

Downhole Monitoring System Pull Condition Condition of downhole monitoring system when pulled: Reusable or Not Reusable

Injection Tubing String Outer Diameter Nominal outer diameter of injection tubing string

Shroud Installed? Was a shroud installed with the PCP system? (Yes/No)

Shroud Outer Diameter Outer diameter of shroud. If a shroud is not installed, then leave .

Packer Installed? Was a packer installed with the PCP system? (Yes/No)

Packer Depth Top Landed At Measured depth to the top of the packer. If a packer is not installed, then leave .

Y-tool Installed? Was a Y-Tool installed with the PCP system? (Yes/No)

Number PCP Systems in Well Number of complete PCP Systems (Motor-Seal-Intake-Pump) installed in the well

Ifthere were/are more thanone PCP S stems installed,where the installed in arallel orin series(char e um

(Single/Tandem/Parallel)

PCP Deployment Method Method used to install/deploy the PCP: Production Tbg, Coiled Tbg, Cable

First PCP System Installed Well? Was/is this PCP installation the first PCP installed in this well?

Equipment Comments

Confidential 3 / 4


4/4





Total Flow Rate Total Flow Rate of produced liquids at standard conditions

Pump Speed Pump rotational speed (RP M)

Torque at Drive Measured torque on the polished rod for surface drive or at motor for downhole drive

Water Cut Water flow rate by %volume of produced liquids. Alternatively, produced oil and water rates may be provided.

Pump Intake Pressure Producing pressure at the pump intake

Producing Fluid Level Measured depth to top of annular fluid level

Free Gas at Pump IntakeFree gas % by volume at the pump intake pressure and temperature (includes both separated gas and gas hand

by the pump).

Wellhead Pressure Pressure of produced fluids at the wellheadCasing Head Pressure Pressure in the casing annulus at the wellhead

Pump Intake TemperatureProducing fluid temperature at the pump intake. If not provided, Pump Intake Temperature will be assumed equ

to the Reservoir Temperature.

Reservoir Static Pressure Static or shut-in pressure at the pump intake

Gas Oil Ratio (GOR) Producing gas-oil ratio. Alternatively, produced gas rate at standard conditions may be provided.

Sand CutConcentration of produced sand by %volume of produced liquids and solids. Alternatively, produced sand rate

be provided. If no sand was produced, please enter zero.

Total Solids Concentration Total concentration of solids (including sand, scale, particulate, etc.)

Scale? Presence and relative severity of sale (None/Light/Moderate/Severe)4

Asphaltenes? Presence and relative severity of asphaltenes (None/ L ight/Moderate/Severe)4

Solids? Presence and severity of all solids, including sand: None, Yes-Present, Light, Moderate, or Severe4

CO2 (% by Volume) Concentration of CO2 (preference by %volume of gas). If no CO2 observed, enter zero.

H2S (% by Volume) Concentration of H2S (preference by %volume of gas). If no H2S observed, enter zero.

Water pH Acidity of produced water - tends to be indication of corrosivity

Water Salinity Chloride concentration - indication of water density and corrosivity

Emulsion? Presence and relative severity of emulsion problem? (None/Light/Moderate/Severe)4Motor Operating Frequency Average frequency (Hz) of power supply to motor; IF surface electric or downhole drive

Motor Operating Voltage Average voltage of power supply to motor, IF surface electric or downhole drive

Motor Operating Current Average current of power supply to motor, IF surface electric or downhole drive

Hydraulic Pressure Average pressure to the hydraulic motor, IF surface electric is a hydraulic drive

Number of Restarts During Period Total number of starts during the production period

Injection Fluid Type of injection fluid, if used (water, diluent, oil)

Injection Fluid Rate Daily rate of injection fluid, if used

Production Period Comments Corrosion Treatments, etc.

Any written or verbal procedure, practices E.g., Pump selection and design (elastomer, target in-test efficiency), startup, speed changes, inspection, discaruidelines

Operating and

Production Data

Practices, ,

manufacture, transportation, inspection,

installation, operating, pulling and/or failure

analysis.

PCP Surveillance System

(SCADA/Operator/Other)

Automatic or Manual Control?

Number General Data Set Parameters = 188

Number Minimum Data Set Parameters = 70

Notes:

2. Duration is the days between Date Period Started and Date Period Ended . Time In Hole is the days between Date Pulled and Date

Installed .

3. In PCP-RIFTS, the ESPCP Cable is considered to be a system comprised of the main power cable (insulation, armor, and conductor

MLE, pothead, splices, packer penetrators, and wellhead penetrator. If any one of these parts is considered Not Reusable, the Cable

System is considered Not Reusable.

4. None: substance or problem not observed.

Yes - P resent: substance or problem is present but the concentration/severity is unknown.

Light: substance or problem observed but in small amount and not believed to be a problem for ESPs.

Moderate: moderate amounts of substance or problem observed, may be or has occasionally been a problem.

Severe: substantial amounts of substance or problem observed, strongly believed or known to be a problem.

1. Parameters in theMinimum Data Set are highlighted in yellow. Click on buttons labeled "1" and "2" in top left corner of spreadsheet

flip between Minimum and General Data Sets, respectively (or filter the parameter list based on column "A").

Confidential 4 / 4

minimum and general data sets

Documents