model: rtrk-521

• Always Wear a Safety Harness with this Product• Practice Using at Ground Level• Tree Size: 9”-18” diameter

Instruction&

Safety Manual

MODEL: RTRK-521Universal Full Treestand Enclosure

Distributed by Acheson Harriman Swan, LLC, 2407 W. Euclid Ave., Littleton, CO 80120©2021 (rev. 1/21)

W A R N I N GEvery year serious injury or death can occur from hunting related accidents. To ensure your safety, please COMPLETELY read and follow this safety manual and ALLwarning labels BEFORE assembling, installing or utilizing this product.

DO NOT USE THIS PRODUCT BEFORE FULLY UNDERSTANDING ALL SAFETYWARNINGS AND INSTRUCTIONS. If you have questions, are unsure about any information or need additional information concerning your product, contact our customerservice department at 1-866-972-6168 or visit www.primalvantage.com/realtree. Keep and maintain this safety and instruction manual in a safe location for future reference.

• Always Wear a Safety Harness with this Product• Practice Using at Ground Level• Tree Size: 9”-18” diameter

Customer Service Department 1-866-972-6168

MODEL: RTRK-521Universal Full Treestand Enclosure

www.primalvantage.com/realtreeDistributed by Acheson Harriman Swan, LLC, 2407 W. Euclid Ave., Littleton, CO 80120

©2021 (rev. 1/21)

2 M8x55mm Bolt...................... Part # 1255

40 2 M6x40mm Bolt....................... Part # 1040

551 M8x45mm Bolt...................... Part # 124545

Blind Enclosure (1)

Spring Pins

A

Front Frame Corner (2)

Spring Pins

B

Rear Frame Corner (2)

Bottom Tree Brace (1)

Frame Supports (2)

Two holeson side

A B

Top Tree Brace (1)E

Side Brace (2)F

C

Bracket (2) H Front Brace (1)I

Vertical Support (1)J

G

J-Hook Buckle (1)

Pole (1) NM M6 Knob (1)O

K

HARDWARE BOX P/N 521RH

2 Frame Supports........................ Part # RK-1015

2 Front Frame Corner..................2 Rear Frame Corner...................

Part # DFF-100Part # DRF-100

2 Side Brace................................ Part # DSB-770

Part # DVS-5911 Blind Enclosure.........................

Part # RK-1025

Part # DTB-510

1 Front Brace...............................

Part # RTBE-521

1 TopTree Brace..........................

1 Vertical Support........................

Part # DTB-5001 Bottom Tree Brace....................

Part # WB-1002 Bracket......................................1 J-Hook Buckle Strap.................

2 M8x55mm Bolt..........................Part # 1255

40 2 M6x40mm Bolt..........................Part # 1040

1 M6 Knob....................................Part # 160055

Part # RK-9035

1 Pole...........................................Part # DTP-100

1 M8x45mm Bolt..........................Part # 124545

PARTS LIST

BCEF

G

H

JKM

NO

A

I

Model: RTRK-521Universal Full Treestand EnclosureAssembly Instructions Page 1

Customer Service Department 1-866-972-6168 www.primalvantage.com/realtreeDistributed by Acheson Harriman Swan, LLC, 2407 W. Euclid Ave., Littleton, CO 80120

©2021 (rev. 1/21)

Slide each Side Brace F onto the other end of Front Frame Corner A .There are three holes on each side brace that MUST be facing the inside of the frame. SEE CLOSEUP

A

FF

I A

Spring Pins

Slide Front Brace I onto Front Frame Corner A .

A AISpring Pin Spring Pin

F

A

Spring Pin

1

2

1

2Closeup


Customer Service Department 1-866-972-6168 www.primalvantage.com/realtreeDistributed by Acheson Harriman Swan, LLC, 2407 W. Euclid Ave., Littleton, CO 80120

©2021 (rev. 1/21)

EB

Spring Pins

B

B

Spring Pin Spring Pin

B E

Slide each Rear Frame Corner B into Side Braces F . B

A

B

F

A

F

I

E

3

4

4

Closeup

3Slide each Rear Frame Corner B into Top Tree Brace E . The “U” part of the brace MUST be on top of the frame.SEE CLOSEUP




©2021 (rev. 1/21)

C

F F

5

5

NOTE: ALL WASHERS ARE AGAINST THE BOLT HEAD AND THE NUT

UNLESS STATED OTHERWISE

40

C FAttach the Frame Supports to the Side Braces using 2-M6x40mm bolt . 40




©2021 (rev. 1/21)

E

J

55

55

55

45

Attach Vertical Support J to Top Tree Brace E with 1-M8x55mm bolt .

Attach both Brackets G to the center hole of Vertical Support J using1-M8x45mm Bolt .

Attach Bottom Tree Brace H to Vertical Support J using 1-M8x55mm Bolt .

J

G

55 H

45

6

6

NOTE: ALL WASHERS ARE AGAINST THE BOLT HEAD AND THE NUT UNLESS STATED OTHERWISE

7

7

Attach left and right Frame Supports to Vertical Support using M6 Knob . The washer should be placed on the end of the bolt against the nut. (See close-up)

CJ O

NOTE: ALL WASHERS ARE AGAINST THE BOLT HEAD AND THE NUT

UNLESS STATED OTHERWISE




©2021 (rev. 1/21)

CC

O

8

8

J

CC

JWasher

O

Close-up

Once the Roof Assembly is secured to the tree, pull Blind Enclosure to the top of the Roof Assembly. Position the Blind Enclosure so the hook and loop opening is in the back against the tree and the hook and loop is not secured. Pull the sides of the Blind Enclosure down unitl it is tight on all four sides.

Starting in one corner, slip the Roof Assmbly frame into the corner pocket of the enclosure. Repeat this step until all four corners are tightly fit onto the frame.

Now attach the Blind Enclosure to all four sides of the Roof Assembly frame using the hook and loop fasteners to secure a snug fit.

Insert pole into the sleeve located along the top center of the Blind Enclosure and into the hole in the middle of the Roof Assembly frame. Push the center of the pole up at an arc until the other end of the shock pole will fit into the other side of the Roof Assmbly frame.


Model: RTRK-521Universal Full Treestand EnclosureInstallation Instructions Page 1


©2021 (rev. 1/21)

9

11

Raise the Roof Assembly to the tree using a safe hoist/lift system to 3 feet above the shooting rail of your treestand.9

Attach the Vertical Support to the tree by usingHook Buckle Strap N .

Hook Buckle Strap N to Bracket G .Wrap the straparound the tree once and attach the other end to thebracket. (See Buckle Strap Instructions). Pull strap until it is tight against the tree.

10

11

N

M

K

G

10

W A R N I N G

K

M

K

K

K

K

Corner Pocket

Corner Pocket

Pole SleeveInsert Pole Here Insert Pole Here

Hook & Loop Fasteners




You MUST use a Hoist system to lift the Roof to the Stand forinstallation. DO NOT climb the Ladder with the Roof and Blind in Hand

NEVER stand on seat platform to attach roof.Raise flip-up seat platform to move closer to tree.

3 Ft.


Model: RTRK-521Universal Full Treestand EnclosureInstallation Instructions Page 2


©2021 (rev. 1/21)

12

Once the roof is secured, close the back of the Blind Enclosureby securing the hook and loop strips from the top to bottom along the back.

12

K

BUCKLE STRAP INSTRUCTIONS

3 Pull strap to desired length.

Hold buckle as shown1

2 Press down on latch and insert strap underneath teeth as shown.

4 Pull slack to tighten.

K

W A R N I N G

Hook & LoopFasteners

WARNING: KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS BLIND FABRIC. This blindmeets the flammability requirements of CPAI-84. It is NOT fireproof. The blind fabric will burn if left in

continuous contact with any flame source. The application of any foreign substance to the blind fabricmay render the flame resistant properties ineffective.

13

14

Attach the 3 hook and loop fasteners alongthe shooting rail of the treestand.13

Tie the bottom of the Blind Enclosure to the Foot Platform of the stand.14

Hook & LoopFasteners

model: rtrk-521

Documents