modelling thermal effects in machining by finite element methods authors andrea bareggi (presenter)...
TRANSCRIPT
MODELLING THERMAL EFFECTS IN MACHINING BY FINITE ELEMENT
METHODS
Authors Andrea Bareggi (presenter) Andrew TorranceGarret O’Donnell
IMC
200
7
Department of Mechanical and Manufacturing Engineering
The University of Dublin
Trinity College
Trinity College Dublin
Introduction
FE modelling for metal cutting• Stress, strain, strain rate predictions• Temperature distribution in the primary,
secondary and tertiary sub-cutting zones
Trinity College Dublin
IMC
200
7
• Cutting forces, plastic deformation (shear angles and chip thickness)
• Temperature in the workpiece, chip and tool
Commercial packagesTrinity College Dublin
IMC
200
7
ABAQUS
• Manual design of geometry, meshing and boundary condition setting
• No material library, but materials can be defined in detail
• Partial support in adaptive remeshing
• Good control of the solver
Commercial packagesTrinity College Dublin
IMC
200
7
ADVANTEDGE
• Very efficient interface to rapidly configure a model, tool library is provided
• Extensive material library
• Uses adaptive remeshing, but controls can not be modified
• Not suitable for customising control functions
IMC
200
7
Commercial packagesTrinity College Dublin
DEFORM 3D
• Built in “wizard” for machining
• Good material library and comprehensive material editor
• Uses adaptive remeshing, good control of meshing parameters
• The user can chose the solver and minimal control is permitted
Problem formulationTrinity College Dublin
IMC
200
7
• Incremental Lagrangian formulation
• Implicit integration method
• Solver with sparse matrix
• Direct method
Problem formulationTrinity College Dublin
• Cutting speed: 270m/min• Feed: 0.06mm/rev• Depth of cut: 0.5mm• Effective rake angle = 0°
nose radius = 0.2mm• Cooling method: air jet• AISI 1020 steel
workpiece,1.5 mm of length, plastic
• WC insert with reduced heat capacity, rigid
workpiece
insert
IMC
200
7
Thermal boundary conditionsTrinity College Dublin
• No cooling, natural convection, h=20 W/m²/K
• Air jet, overhead position, h=2000 W/m²/K
• Air jet, interface position, h=2000 W/m²/K
IMC
200
7
overhead
interface
Interface nozzle dir.
Overhead nozzle dir.
ResultsTrinity College Dublin
IMC
200
7
• Steady state condition: workpiece, interface, insert
• Temperature prediction: workpiece, chip and interface
Chip temperature(416°C)
ResultsTrinity College Dublin
IMC
200
7
feed=0.06mm/revdepth=0.5mmspeed=270m/min
Maxworkpiecetemp. (°C)
Interface temp. (°C)
Chip temp. (°C)
CuttingForce (N)
Dry cutting 737 710 416 93Air jet cooling,
overhead721 627 389 92
Air jet cooling, interface
727 648 408 95
• Reduction of interface temperature• Best cooling in overhead position• No influence on the cutting force
ResultsTrinity College Dublin
IMC
200
7
• Prediction of gradient temperature within the insert
• Developing of experimental techniques for investigating temperature
Temp (°C)
A=20
B=88
C=156
D=225
E=293
F=361
G=429
H=498
I=566
J=634
K=702
ConclusionTrinity College Dublin
IMC
200
7
• Results consistency: analytical results, ADVANTEDGE simulations, preliminary temperature measurements
• Finite Elements: cost saving in experimental work, process insight in cooling and lubricating method
• 3D modelling techniques under development, in particular with cooling
Further researchTrinity College Dublin
IMC
200
7
• Refinement of the model, estimation of the heat transfer coefficients, improved approach to jet modelling
• Simulation with different workpiece materials and cutting conditions
• Experimental validation, currently ongoing
Literature & AcknowledgementsTrinity College Dublin
IMC
200
7
•N.A. Abukhshim, P.T. Mativenga, M.A. Sheikh, Heat generation and temperature prediction in metal cutting: A review and implications for high speed machining, International Journal of Machine Tools & Manufacture 46 (2006) 782–800•J.D. Gardner, A.Vijayaraghavan, D.A. Dornfeld, Comparative Study of Finite Element Simulation Software, eScholarship Repository, University of California, Copyright c 2005 by the authors•T. O’Donovan, Fluid flow and heat transfer of an impinging air jet, Phd. Thesis, Mechanical & Manufacturing Engineering, Trinity College Dublin, 2005•D. Umbrello, L. Filice, S. Rizzuti, F. Micari, On the evaluation of the global heat transfer coefficient in cutting, International Journal of Machine Tools & Manufacture 47 (2007) 1738–1743
Literature & AcknowledgementsTrinity College Dublin
IMC
200
7
AcknowledgementsChristian E. Fischer, Ph.D., PE, (Scientific Forming Technologies Corporation, Columbus, Ohio, USA)
Questions?