mop third carrier version1.3

MOP

Third Carrier

HUAWEI Technologies Co., Ltd.

July, 2013

Third Carrier Implementation

1 SUMMARY Third Carrier Implementation: Modify existing S/2/2/2 configuration become to S/3/3/3 with adding new WRFU board scenario to keep the 40W /carrier after the activation.

RNC and Nodeb Hardware & Software Version :

Network Equipment Current Version

RNC BSC6900 UO UMTS V900R013ENGC00SPH552

NodeB BTS3900/BTS3900A/BTS3900L (Macro Site) WCDMA V200R013C00SPC339

Technical Implementation: Site Hardware Reconfiguration and Installation ( Insert WBBP , WRFU, Interconnection cable

and CPRI cable connection) Data Configuration

Site Hardware Installation:

Site Hardware Qty

S333 Site

1 Add WRFU board 3

2 Add CPRI cable 3

3 Add WBBP 1

Nodeb Hardware Installation Overview:

2 Network impact for Third Carrier

NodeB service would be down about 70 minutes. It only impacts one site service.

3 RNC SIDE CONFIGURATION

3..1 Objective Third Carrier configuration at RNC side

Data Configuration NE Remark 1. Deactivate cell RNC RF

2. Add Ulocell RNC RF

3. Add USAC RNC RF

4. Add UCELLQUICKSETUP RNC RF

5. Activate cell RNC RF

3..2 Preparation Before Execution Backup Existing Script

BKP DB:;

EXP CFGMML:;

3..3 Procedure and Work Flow Step 1 Deactivate Cell DSP UCELL: DSPT=BYNODEB, NodeBName="xxx";

DEA UCELL: CellId=xxx;






Noted : after deactivated ucell, subcon on site can directly change the jumper connection

Step 2 Add Ulocell ADD ULOCELL: NodeBName="abc", LoCell=xxx;

ADD ULOCELL: NodeBName="abc", LoCell=xxx;

ADD ULOCELL: NodeBName="abc", LoCell=xxx;

Step 3 Add USAC ADD USAC: CnOpIndex=0, LAC=xxx, SAC=xxx; ADD USAC: CnOpIndex=0, LAC=xxx, SAC=xxx; ADD USAC: CnOpIndex=0, LAC=xxx, SAC=xxx; Step 4 Add UCELLQUICKSETUP (noted: Third Carrier used this frequency for ULFREQ=9788, DLFREQ=10738, SpgID used 2, all data provided at CDR)

ADD UCELLQUICKSETUP: CellId=xxx, CellName="ABC", PeerIsValid=INVALID, CnOpGrpIndex=0,

BandInd=Band1, UARFCNUplink=9788, UARFCNDownlink=10738, PScrambCode=xxx, Tcell=CHIP0,

LAC=xxx, SAC=xxx, CfgRacInd=REQUIRE, RAC=xxx, SpgId=2, URANUM=D1, URA1=xxx,

NodeBName="ABC", LoCell=xxx, MaxTxPower=xxx, PCPICHPower=xxx;

Step 5 Add UCELLHSDPA // HSPA + 21Mbps ADD UCELLHSDPA: CellId=xxx, AllocCodeMode=Automatic, CodeAdjForHsdpaSwitch=ON,

CodeAdjForHsdpaUserNumThd=3;

MOD UCELLALGOSWITCH: CellId=xxx, NBMCacAlgoSwitch=CRD_ADCTRL-1&HSDPA_UU_ADCTRL-1,

NBMLdcAlgoSwitch=UL_UU_LDR-1&DL_UU_LDR-1&CELL_CODE_LDR-1&CELL_CREDIT_LDR-1,

HspaPlusSwitch=64QAM-1&DL_L2ENHANCED-1;

Step 6 Add UCELLHSUPA // HSUPA 5.7Mbps ADD UCELLHSUPA:CELLID=xxx, EAGCHCODENUM=1, ERGCHEHICHCODENUM=1,

MAXTARGETULLOADFACTOR=75, NONSERVTOTOTALEDCHPWRRATIO=0;

4 NODEB SIDE Hardware & Configuration implementation

4..1 Objective Third Carrier configuration at Nodeb side and installation nodeb hardware

Nodeb Hardware Installation Scenario :

Macro Site Scenario

4..2 Preparation Before Execution Backup Existing Script

Nodeb.xml

Check Existing Nodeb Alarm LST ALMAF

4..3 Procedure and Work Flow

Step 1 Add WBBP Board if only one

DSP BRD:;

ADD BRD: SN=2, BT=WBBP;

Step 2 List and add RRU , RRU Chain based on topology above (Noted: add RRU and RRUchain make sure check cpri cable which is connected from WRFU to WBBP, usually new board used wrfu board at slot 1, 3, 5 and wbbp board slot 2) LST RRU:;

LST RRUCHAIN:;

ADD RRU: CN=0, SRN=xxx, SN=xxx, TP=TRUNK, RCN=xxx, PS=0, RT=WRFU, RS=UO, ALMPROCSW=ON;



ADD RRUCHAIN: RCN=xxx, TT=CHAIN, BM=COLD, HSN=2, HPN=0;



HSN (Head Slot No): only can configured at slot 2 and 3 only

Step 3 List and Add ULgroup/DLgroup and WBBP board based on topology above (Noted: Third Carrier usually used DLgoup and ULgroup no 1 & WBBP board at slot 2, before add this board make sure there are cpri cable connected to WRFU board for wbbp board allocation)

LST DLGROUP: DLGROUPN=xxx;

LST ULGROUP: ULGROUPN=xxx;

RMV DLGROUP: DLGROUPN=0;

RMV ULGROUP: ULGROUPN=0;

ADD ULGROUP: ULGROUPN=0, DEMMODE=DEM_2_CHAN, SNE1=3;

ADD DLGROUP: DLGROUPN=0, SNE1=3;

ADD ULGROUP: ULGROUPN=1, DEMMODE=DEM_2_CHAN, SNE1=2;

ADD DLGROUP: DLGROUPN=1, SNE1=2;

Step 4 Modify RX mode (Reconfigure XL Axiata RX mode) (Noted: Before Modify list first and backup all information as attached below)

Lst Locell and Sector nodeb ran sharing.txt

// Remove XL Cell to Configure antenna Sector

LST LOCELL: MODE=LOCALCELL, LOCELL=xxx

RMV LOCELL:LOCELL=1;






LST SEC: STN=xxx, SECN=xxx

RMV SEC: STN=xxx, SECN=0;



// Reconfigure XL antenna Sector

ADD SEC: STN=xxx, SECN=0, SECT=LOCAL_SECTOR, ANTM=2, RFINTERCONN=FALSE, ANT1CN=1,

ANT1SRN=4, ANT1N=N0A, ANT2CN=1, ANT2SRN=4, ANT2N=N1A;





// Reconfigure XL locall cell ADD LOCELL: LOCELL=1, STN=xxx, SECN=0, SECT=LOCAL_SECTOR, ULGROUPNO=0, DLGROUPNO=0, TTW=FALSE, CN1=1, SRN1=4, SN1=0, ULFREQ=9813, DLFREQ=10763, MXPWR=460,

HISPM=FALSE, RMTCM=FALSE, VAM=FALSE;

ADD LOCELL: LOCELL=2, STN=xxx, SECN=1, SECT=LOCAL_SECTOR, ULGROUPNO=0,

DLGROUPNO=0, TTW=FALSE, CN1=1, SRN1=4, SN1=2, ULFREQ=9813, DLFREQ=10763, MXPWR=460,





ADD LOCELL: LOCELL=4, STN=xxx, SECN=0, SECT=LOCAL_SECTOR, ULGROUPNO=0, DLGROUPNO=0, TTW=FALSE, CN1=1, SRN1=4, SN1=0, ULFREQ=9838, DLFREQ=10788, MXPWR=460,








Third Carrier Implementation //In NodeB

ADD LOCELL: LOCELL=7, STN=xxx, SECN=0, SECT=LOCAL_SECTOR, ULGROUPNO=1, DLGROUPNO=1, TTW=FALSE, CN1=1, SRN1=4, SN1=1, ULFREQ=9788, DLFREQ=10738, MXPWR=460,








HSPA + 21Mbps & HSUPA 5.7Mbps //In NodeB SET MACHSPARA: LOCELL=xxx, DYNCODESW=OPEN;

SET MACHSPARA: LOCELL=xxx, SM=EPF;

Step 5 Active Cell From RNC side (Note: activate cell when NodeB configuration done)

ACT UCELL: CellId=xxx;



ACT UCELLHSDPA: CellId=xxx;



ACT UCELLHSUPA: CellId=xxx;



DSP UCELL: DSPT=BYNODEB, NodeBName="xxx";

Step 6 In M2000 please updates the license from S/2/2/2 configuration become S/3/3/3 Configuration

5. ROLL BACK EXECUTION RNC SIDE

Step 1. RMV ULOCELL: NodeBName="ABC", LoCell=7;

Step 2. RMV USAC: CnOpIndex=0, LAC=xxx, SAC=xxx; Step 3. RMV UCELL: CellId=xxx;

NodeB SIDE

Step 1. Reload the backup .xml script and change the configuration installation become existing ones

6. Testing after operation It needs team to verify service on site after operation

7. KPI monitor and CPU load monitor on M2000

a. Monitor after operation: // KPI monitor and CPU load monitor.

// check alarms which should be compared with the alarms before operation. // Verify the service through LMT

b. Monitor at first Busy Hour after operation: // KPI monitor

8. Operation time Maintenance time window. (00:00 until 04:00 am)

Revision Record

Date Revised Version Change description Author

26/06/2013 1.0 Hendra Wijaya

H00738385

27/06/2013 1.1

Add ucellhsdpa and Add ucellhsupa (HSPA + 21Mbps & HSUPA 5.7Mbps)

Hendra Wijaya

H00738385


H00738385


H00738385

mop third carrier version1.3

Documents