motor-drive unit tapmotion® td ism® · 2018. 1. 17. · the tapmotion® td ism® motor-drive...

Motor-drive UnitTAPMOTION® TD ISM®

Operating Instructions

4489615/01 EN . OEM-Control-Box

© All rights reserved by Maschinenfabrik ReinhausenDissemination and reproduction of this document and use and disclosure of its content are strictly prohibitedunless expressly permitted.Infringements will result in liability for compensation. All rights reserved in the event of the granting of patents,utility models or designs.The product may have been altered since this document was published.We reserve the right to change the technical data, design and scope of supply.Generally the information provided and agreements made when processing the individual quotations and ordersare binding.The original operating instructions were written in German.

Table of contents

Maschinenfabrik Reinhausen GmbH 2016 34489615/01 EN TAPMOTION® TD ISM®

Table of contents

1 Introduction......................................................................................................................... 51.1 Validity................................................................................................................................................. 5

1.2 Manufacturer....................................................................................................................................... 5

1.3 Subject to change without notice......................................................................................................... 5

1.4 Supporting documents......................................................................................................................... 5

1.5 Safekeeping......................................................................................................................................... 6

1.6 Notation conventions........................................................................................................................... 61.6.1 Symbols................................................................................................................................................................. 6

1.6.2 Hazard communication system............................................................................................................................. 7

1.6.3 Information system................................................................................................................................................ 8

1.6.4 Instruction system................................................................................................................................................. 8

1.6.5 Typographic conventions...................................................................................................................................... 9

2 Safety................................................................................................................................. 102.1 General safety information................................................................................................................ 10

2.2 Appropriate use................................................................................................................................. 10

2.3 Inappropriate use............................................................................................................................... 10

2.4 Personnel qualification...................................................................................................................... 11

2.5 Operator's duty of care...................................................................................................................... 11

2.6 Personal protective equipment.......................................................................................................... 11

3 Product description.......................................................................................................... 133.1 Scope of delivery............................................................................................................................... 13

3.2 Function description.......................................................................................................................... 13

3.3 Design............................................................................................................................................... 13

4 Packaging, transport and storage................................................................................... 154.1 Packaging.......................................................................................................................................... 154.1.1 Suitability............................................................................................................................................................. 15

4.1.2 Markings.............................................................................................................................................................. 15

4.2 Transportation, receipt and handling of shipments............................................................................ 16

4.3 Storage of shipments......................................................................................................................... 17

4.4 Unpacking shipments and checking for transportation damages...................................................... 18

5 Installation and commissioning...................................................................................... 19

Table of contents

Maschinenfabrik Reinhausen GmbH 20164 4489615/01 ENTAPMOTION® TD ISM®

6 Operation........................................................................................................................... 21

7 Maintenance and care....................................................................................................... 22

8 Fault elimination................................................................................................................ 23

9 Disposal............................................................................................................................. 24

10 Technical data................................................................................................................... 25

1 Introduction


IntroductionThis technical file contains detailed descriptions on the safe and proper in-stallation, connection, commissioning and monitoring of the product.

It also includes safety instructions and general information about the prod-uct.

This technical file is intended solely for specially trained and authorized per-sonnel.

ValidityThis technical file is valid for the TAPMOTION® TD ISM® product.

ManufacturerThe product is manufactured by:

Maschinenfabrik Reinhausen GmbH

Falkensteinstraße 893059 Regensburg, GermanyTel.: (+49) 9 41/40 90-0Fax: (+49) 9 41/40 90-7001E-mail: [email protected]

Further information on the product and copies of this technical file are avail-able from this address if required.

Subject to change without noticeThe information contained in this technical file comprises the technical speci-fications approved at the time of printing. Significant modifications will be in-cluded in a new edition of the technical file.

The document number and version number of this technical file are shown inthe footer.

Supporting documentsThe following documents also apply in addition to this technical file:▪ Connection diagrams▪ Routine test report▪ Supplement

Also observe generally valid legislation, standards, guidelines and specifica-tions on accident prevention and environmental protection in the respectivecountry of use.

1

1.1

1.2

1.3

1.4

1 Introduction


SafekeepingThis technical file and all supporting documents must be kept ready at handand accessible for future use at all times.

Notation conventionsThis section contains an overview of the symbols and textual emphasisused.

Symbols

Symbol MeaningWrench size

Tightening torque

Number and type of fastening materials used

Fill with oil

Cut open, cut through

Clean

Visual inspection

Use your hand

Adapter ring

Apply a coat of paint

Use a file

Grease

1.5

1.6

1.6.1

1 Introduction


Symbol MeaningCoupling bolt

Use a ruler

Use a saw

Hose clip

Wire eyelet, safety wire

Use a screwdriver

Table 1: Symbols

Hazard communication system

Warnings in this technical file are displayed as follows.

Warning relating to section

Warnings relating to sections refer to entire chapters or sections, sub-sec-tions or several paragraphs within this technical file. Warnings relating tosections use the following format:

WARNING Type and source of dangerConsequences► Action► Action

Embedded warning information

Embedded warnings refer to a particular part within a section. These warn-ings apply to smaller units of information than the warnings relating to sec-tions. Embedded warnings use the following format:

DANGER! Instruction for avoiding a dangerous situation.

Signal words and pictograms

The following signal words are used:

1.6.2

1.6.2.1

1.6.2.2

1.6.2.3

1 Introduction


Signalword

Meaning

DANGER Indicates a hazardous situation which, if not avoided, willresult in death or serious injury.

WARNING Indicates a hazardous situation which, if not avoided, couldresult in death or serious injury.

CAUTION Indicates a hazardous situation which, if not avoided, couldresult in injury.

NOTICE Indicates measures to be taken to prevent damage toproperty.

Table 2: Signal words in warning notices

Pictograms warn of dangers:

Pictogram MeaningWarning of a danger point

Warning of dangerous electrical voltage

Warning of combustible substances

Warning of danger of tipping

Table 3: Pictograms used in warning notices

Information system

Information is designed to simplify and improve understanding of particularprocedures. In this technical file it is laid out as follows:

Important information.

Instruction system

This technical file contains single-step and multi-step instructions.

1.6.3

1.6.4

1 Introduction


Single-step instructions

Instructions which consist of only a single process step are structured as fol-lows:

Aim of actionü Requirements (optional).► Step 1 of 1.

ð Result of step (optional).ð Result of action (optional).

Multi-step instructions

Instructions which consist of several process steps are structured as follows:

Aim of actionü Requirements (optional).1. Step 1.

ð Result of step (optional).2. Step 2.

ð Result of step (optional).ð Result of action (optional).

Typographic conventions

The following typographic conventions are used in this technical file:

Typographic convention Purpose ExampleUPPERCASE Operating controls, switches ON/OFF[Brackets] PC keyboard [Ctrl] + [Alt]Bold Software operating controls Press Continue button…>…>… Menu paths Parameter > Control parameterItalics System messages, error mes-

sages, signalsFunction monitoring alarm trig-gered

[► Number of pages]. Cross reference [► 41].Table 4: Typographic conventions

1.6.5

2 Safety


Safety

General safety informationThe technical file contains detailed descriptions on the safe and proper in-stallation, connection, commissioning and monitoring of the product.▪ Read this technical file through carefully to familiarize yourself with the

product.▪ Particular attention should be paid to the information given in this chap-

ter.

Appropriate useIf used as intended and in compliance with the requirements and conditionsspecified in this technical file as well as the warning notices in this technicalfile and attached to the product, then the product does not present any haz-ards to people, property or the environment. This applies throughout theproduct's entire life, from delivery through installation and operation to disas-sembly and disposal.

The operational quality assurance system ensures a consistently high qualitystandard, particularly in regard to the observance of health and safety re-quirements.

The following is considered appropriate use▪ Only operate the product in accordance with this technical file and the

agreed delivery conditions and technical data.▪ Always operate the product under supervision.▪ Use the equipment and special tools supplied solely for the intended

purpose and in accordance with the specifications of this technical file.▪ Only use the product for commissioning an on-load tap-changer using

the TAPMOTION® TD ISM® motor-drive unit.

Inappropriate useUse is considered to be inappropriate if the product is used other than as de-scribed in the Appropriate use section. Please also note the following:▪ Risk of explosion and fire from highly flammable or explosive gases, va-

pors, or dusts. Do not operate product in areas at risk of explosion.▪ Risk of personal injury and damage to property from electric shock. Do

not use product on an energized transformer.▪ Unauthorized or inappropriate changes to the product may lead to per-

sonal injury, material damage, and operational faults. Only modify prod-uct following discussion with Maschinenfabrik Reinhausen GmbH.

2

2.1

2.2

2.3

2 Safety


Personnel qualificationThe product is designed solely for use in electrical energy systems and facili-ties operated by appropriately trained staff. This staff comprises people whoare familiar with the installation, assembly, commissioning and operation ofsuch products.

Operator's duty of careTo prevent accidents, disruptions and damage as well as unacceptable ad-verse effects on the environment, those responsible for transport, installa-tion, operation, maintenance and disposal of the product or parts of the prod-uct must ensure the following:▪ All warning and hazard notices are complied with.▪ Personnel are instructed regularly in all relevant aspects of operational

safety, the operating instructions and particularly the safety instructionscontained therein.

▪ Regulations and operating instructions for safe working as well as therelevant instructions for staff procedures in the case of accidents andfires are kept on hand at all times and are displayed in the workplacewhere applicable.

▪ The product is only used when in a sound operational condition andsafety equipment in particular is checked regularly for operational relia-bility.

▪ Only replacement parts, lubricants and auxiliary materials which are au-thorized by the manufacturer are used.

▪ The specified operating conditions and requirements of the installationlocation are complied with.

▪ All necessary devices and personal protective equipment for the specificactivity are made available.

▪ The prescribed maintenance intervals and the relevant regulations arecomplied with.

▪ Installation, electrical connection and commissioning of the product mayonly be carried out by qualified and trained personnel in accordancewith this technical file.

▪ The operator must ensure appropriate use of the product.

Personal protective equipmentPersonal protective equipment must be worn during work to minimize risks tohealth.▪ Always wear the personal protective equipment required for the job at

hand.▪ Follow information about personal protective equipment provided in the

work area.

2.4

2.5

2.6

2 Safety


Always wear Protective clothingClose-fitting work clothing with a lowbreaking strength, with tight sleeves andwith no protruding parts. It mainly servesto protect the wearer against being caughtby moving machine parts.Do not wear any rings, necklaces or otherjewelry.Safety shoesTo protect against falling heavy objectsand slipping on slippery surfaces.

Table 5: Personal protective equipment to be worn at all times

Wear the following in spe-cial environments

Special personal protective equipmentis needed in special environments.The choice of equipment depends onthe circumstances.Safety glassesTo protect the eyes from flying parts andsplashing liquids.

Hard hatTo protect from falling and flying parts andmaterials.

Hearing protectionTo protect from hearing damage.

Table 6: Personal protective equipment to be worn in special environments

3 Product description


Product descriptionThis chapter contains an overview of the design and function of the product.

Scope of deliveryThe OEM Control Box is packaged with protection against moisture and isdelivered as follows:▪ OEM Control Box▪ Product documentation

Please note the following:► Check the shipment for completeness using the shipping documents.

Function descriptionThe OEM Control Box is used to actuate the TAPMOTION® TD ISM® mo-tor-drive unit's gear motor manually if the control cabinet is not yet installedand connected (e.g. for test tap-change operations at the transformer plant).

DesignThe OEM Control Box consists of the following components:

Figure 1: OEM Control Box

1 OEM Control Box 3 Control cable2 Connecting lead

3

3.1

3.2

3.3

3 Product description


The OEM Control Box contains the following operating controls and displayelements:

Figure 2: Operating controls

1 Motor protective switch 2 In Position LED3 Error LED 4 EMERGENCY OFF switch5 AUTO/MANUAL switch 6 N key7 1 key

4 Packaging, transport and storage


Packaging, transport and storage

PackagingThe products are sometimes supplied with a sealed packaging and some-times also dried depending on what is required.

A sealed packaging surrounds the packaged goods on all sides with plasticfoil. Products that have also been dried are identified by a yellow label on thesealed packaging.

The information in the following sections should be applied as appropriate.

Suitability

NOTICE

Property damage due to incorrectly stacked crates!Stacking the crates incorrectly can lead to damage to the packaged goods!► Only stack up to 2 equally sized crates on top of one another.

The packaging is suitable for undamaged and fully functional means oftransportation in compliance with local transportation laws and regulations.

The packaged goods are packed in a stable crate. This crate ensures thatthe packaged goods are secure when in the intended transportation positionand that none of the parts touch the loading surface of the means of trans-port or touch the ground after unloading.

The packaged goods are stabilized inside the crate to prevent impermissiblechanges in position.

A sealed packaging surrounds the packaged goods on all sides with plasticfoil. The packaged goods are protected from humidity using a desiccant. Theplastic foil is bonded after the drying agent is added.

Markings

The packaging bears a signature with instructions for safe transport and cor-rect storage. The following symbols apply to the shipment of non-hazardousgoods. Adherence to these symbols is mandatory.

Protectagainst

moisture

Top Fragile Attach liftinggear here

Center ofmass

Table 7: Shipping pictograms

4

4.1

4.1.1

4.1.2



Transportation, receipt and handling of shipments

WARNING Danger of death and damage to property!Danger of death and damage to property due to tipping or falling load!► Transport crate only when closed.► Do not remove the mounting material used in the crate during transport.► Only trained and appointed persons may select the sling gear and se-

cure the load.► Do not walk under the hanging load.► Use means of transport and lifting gear with a sufficient carrying capaci-

ty in accordance with the weight stated on the delivery slip.

In addition to oscillation stress and shock stress, jolts must also be expectedduring transportation. In order to prevent possible damage, avoid dropping,tipping, knocking over and colliding with the product.

If a crate tips over, falls from a certain height (e.g. when slings tear) or expe-riences an unbroken fall, damage must be expected regardless of theweight.

Every delivered shipment must be checked for the following by the recipientbefore acceptance (acknowledgment of receipt):▪ Completeness based on the delivery slip▪ External damage of any type.

The checks must take place after unloading when the crate or transport con-tainer can be accessed from all sides.

If external transport damage is detected on receipt of the shipment, proceedas follows:▪ Immediately record the transport damage found in the shipping docu-

ments and have this countersigned by the carrier.▪ In the event of severe damage, total loss or high damage costs, immedi-

ately notify the sales department at Maschinenfabrik Reinhausen andthe relevant insurance company.

▪ After identifying damage, do not modify the condition of the shipmentfurther and retain the packaging material until an inspection decisionhas been made by the transport company or the insurance company.

▪ Record the details of the damage immediately onsite together with thecarrier involved. This is essential for any claim for damages!

▪ Photograph damage to packaging and packaged goods. This also ap-plies to signs of corrosion on the packaged goods due to moisture insidethe packaging (rain, snow, condensation).

▪ NOTICE! Be absolutely sure to also check the sealed packaging. If thesealed packaging is damaged, do not under any circumstances install orcommission the packaged goods. Either dry the dried packaged goodsagain as per the operating instructions for the relevant on-load tap-

4.2

Visible damage



changer/off-circuit tap-changer or contact Maschinenfabrik ReinhausenGmbH to agree on how to proceed with drying. If this is not done, thepackaged goods may be damaged.

▪ Name the damaged parts.

When damages are not determined until unpacking after receipt of the ship-ment (hidden damage), proceed as follows:▪ Make the party responsible for the damage liable as soon as possible by

telephone and in writing, and prepare a damage report.▪ Observe the time periods applicable to such actions in the respective

country. Inquire about these in good time.

With hidden damage, it is very hard to make the transportation company (orother responsible party) liable. Any insurance claims for such damages canonly be successful if relevant provisions are expressly included in the insur-ance terms and conditions.

Storage of shipments

Packaged goods dried by Maschinenfabrik Reinhausen

Upon receipt of the shipment, immediately remove the packaged goodsdried by Maschinenfabrik Reinhausen from the sealed packaging and storeair-tight in dry insulating oil until used.

Non-dried packaged goods

Non-dried packaged goods but with a functional sealed packaging can bestored outdoors when the following conditions are complied with.

When selecting and setting up the storage location, ensure the following:▪ Protect stored goods against moisture (flooding, water from melting

snow and ice), dirt, pests such as rats, mice, termites and so on, andagainst unauthorized access.

▪ Store the crates on timber beams and planks as a protection against ris-ing damp and for better ventilation.

▪ Ensure sufficient carrying capacity of the ground.▪ Keep entrance paths free.▪ Check stored goods at regular intervals. Also take appropriate action af-

ter storms, heavy rain or snow and so on.

Protect the packaging foil from direct sunlight so that it does not disintegrateunder the influence of UV rays, which would cause the packaging to lose itssealing function.

If the product is installed more than 6 months after delivery, suitable meas-ures must be taken without delay. The following measures can be used:▪ Correctly regenerate the drying agent and restore the sealed packaging.

Hidden damage

4.3



▪ Unpack the packed goods and store in suitable storage space (well ven-tilated, as dust-free as possible, humidity < 50 % where possible).

Unpacking shipments and checking for transportationdamages▪ NOTICE! Transport the packaged crate to the place where installation

will take place. Do not open the sealed packaging until just before instal-lation. If this is not done, damage to the packaged goods may occur dueto ineffectively sealed packaging.

▪ WARNING! When unpacking, check the condition of the packagedgoods.Secure packaged goods in an upright crate from tipping out. Ifthis is not done, the packaged goods may be damaged and serious inju-ries may result.

▪ Check completeness of supplementary parts on the basis of the deliveryslip.

4.4

5 Installation and commissioning


Installation and commissioningThis chapter describes how to correctly connect and commission the OEMControl Box.

WARNING Risk of severe injury or death!An energized transformer and energized on-load tap-changer componentscan cause death or serious injuries when installing the motor-drive unit!► Ensure de-energized state of transformer and on-load tap-changer

components during the installation of the motor-drive unit.

You may only connect the OEM Control Box to circuits with an external over-current protection device and an isolating device with all poles disconnectedso the equipment can be fully de-energized if required (service, maintenanceetc.).

Suitable equipment includes isolating devices in accordance with IEC60947-1 and IEC60947-3 (e.g. circuit breaker). When selecting the circuitbreaker type, note the properties of the relevant circuits (voltage, maximumcurrents). Please also note the following:▪ It must be easy for the operator to access the isolating device▪ The isolating device must be labeled for the device circuits to be isolat-

ed▪ The isolating device must not be part of the power line▪ The isolating device must not interrupt the main grounding conductor

You must fuse the power supply circuit with a C16A type miniature circuitbreaker.

To install and commission the OEM Control Box, proceed as follows:1. Connect the connecting lead to the gear motor's plug connector.2. Connect OEM Control Box to the power supply.

The CEE plug for the OEM Control Box power supply is configured for aclockwise rotary field.

5

5 Installation and commissioning


3. Configure motor protective switch according to the gear motor's ratedcurrent and tripping class. To do so, note the table below.

Figure 3: Configuring motor protective switch

Rated current and tripping class of the gear motor

Motor designation In CLASS

380 V 400 V 440 VGear motor VM 50 Hz 1.0 A 10Gear motor VM 60 Hz 1.0 AGear motor VV 50 Hz 1.4 A 1.4 A 1.8 AGear motor VV 60 Hz 1.4 A 1.5 A 1.7 A

Table 8: Rated current (In) and tripping class (CLASS) of the connected gear motor

6 Operation


OperationYou can control the TAPMOTION® TD ISM® motor-drive unit's gear motorusing the OEM Control Box in two different operating modes:▪ MANUAL: In MANUAL mode, the gear motor only runs as long as key 1

or N is pressed and held down. This allows you to move the gear motorincrementally.

▪ AUTO: In AUTO operating mode, the gear motor runs until the on-loadtap-change operation is completely finished after pressing key 1 or N.

To activate the gear motor, proceed as follows:1. Move MANUAL/AUTO switch to the desired position to select the oper-

ating mode.2. Press or press and hold key 1 or key N to activate the gear motor ac-

cording to the operating mode selected.ð The gear motor runs. Then, if the gear motor is in a defined tap position,

the In Position lamp lights up. Otherwise, the Error lamp lights up.

6

7 Maintenance and care


Maintenance and careYou can clean the device's housing with a dry cloth.

7

8 Fault elimination


Fault eliminationThis chapter describes how to eliminate simple operating faults.

Characteristics/detail Cause RemedyNo function in AUTOoperating mode▪ ERROR LED

lights up

On-load tap-changer is inimpermissible position

Bring on-load tap-changer to a permissible posi-tion:1. Select MANUAL mode.2. Push key 1 or key N to move the on-load

tap-changer into a permissible position. Ifthe tap changer is in a permissible position,the IN POSITION lamp lights up.

No function No power supply Check power supply.Miniature circuit breaker F14triggered

Engaging miniature circuit breaker:1. Remove device from the network.2. Remove cover plate cross recessed head

screws and lift cover plate.3. Engaging miniature circuit breaker F14:4. Install cover plate.5. Connect device and check function.If faults persist: contact Maschinenfabrik Rein-hausen GmbH.

Miscellaneous error Contact Maschinenfabrik Reinhausen.Table 9: Fault elimination

Other faults

In the event of faults that cannot be easily corrected on site, please informyour authorized MR representative or contact us directly:

Maschinenfabrik Reinhausen GmbHTechnical ServicePostfach 12 03 6093025 RegensburgGermany

Phone: (+49) 9 41/40 90-0Fax: (+49) 9 41/40 90-7001

E-mail: [email protected]: www.reinhausen.com

8

9 Disposal


DisposalThe device was produced in accordance with European Community Direc-tive 2011/65/EC (RoHS) and must be disposed of accordingly. If the deviceis not operated within the European Union, the national disposal require-ments applicable in the country of use should be observed.

9

10 Technical data


Technical data

Dimensions and weight

Dimensions (W x H x D) 265 x 315 x 198 mmWeight 1.7 kg

Table 10: Dimensions and weight

Electrical connection loads

Power supply 400 VACFrequency 50/60 HzPower consumption approx. 4 AFuse Miniature circuit breaker 1.6 A type

C

Motor protective switch, dependingon the setting of the gear motor'srated current

Table 11: Electrical connection loads

Figure 4: Position of the miniature circuit breaker if cover plate is disassembled

F14 Miniature circuit breaker

Ambient conditions

Degree of protection IP65 (if cover closed)Operating temperature 5...40 °CStorage temperature -20…+50 °C

Table 12: Ambient conditions

10

MR worldwideAustraliaReinhausen Australia Pty. Ltd.17/20-22 St Albans RoadKingsgrove NSW 2208Phone: +61 2 9502 2202Fax: +61 2 9502 2224E-Mail: [email protected]

BrazilMR do Brasil Indústria Mecánica Ltda.Av. Elias Yazbek, 465CEP: 06803-000Embu - São PauloPhone: +55 11 4785 2150Fax: +55 11 4785 2185E-Mail: [email protected]

CanadaReinhausen Canada Inc.3755, rue Java, Suite 180Brossard, Québec J4Y 0E4Phone: +1 514 370 5377Fax: +1 450 659 3092E-Mail: [email protected] IndiaEasun-MR Tap Changers Ltd. (Joint Venture)612, CTH RoadTiruninravur, Chennai 602 024Phone: +91 44 26300883Fax: +91 44 26390881E-Mail: [email protected] IndonesiaPt. Reinhausen IndonesiaGerman Center, Suite 6310,Jl. Kapt. Subijanto Dj.BSD City, TangerangPhone: +62 21 5315-3183Fax: +62 21 5315-3184E-Mail: [email protected]

IranIran Transfo After Sales Services Co.(Joint Venture)Zanjan, Industrial Township No. 1 (Aliabad)Corner of Morad Str.Postal Code 4533144551E-Mail: [email protected] ItalyReinhausen Italia S.r.l.Via Alserio, 1620159 MilanoPhone: +39 02 6943471Fax: +39 02 69434766E-Mail: [email protected] JapanMR Japan CorporationGerman Industry Park1-18-2 Hakusan, Midori-kuYokohama 226-0006Phone: +81 45 929 5728Fax: +81 45 929 5741 LuxembourgReinhausen Luxembourg S.A.72, Rue de PrésL-7333 SteinselPhone: +352 27 3347 1Fax: +352 27 3347 99E-Mail: [email protected]

MalaysiaReinhausen Asia-Pacific Sdn. BhdLevel 11 Chulan TowerNo. 3 Jalan Conlay50450 Kuala LumpurPhone: +60 3 2142 6481Fax: +60 3 2142 6422E-Mail: [email protected]

P.R.C. (China)MR China Ltd. (MRT)开德贸易（上海）有限公司

中国上海浦东新区浦东南路 360 号

新上海国际大厦 4楼 E座

邮编： 200120

电话：＋ 86 21 61634588

传真：＋ 86 21 61634582

邮箱：[email protected]

[email protected]

Russian FederationOOO MRNaberezhnaya Akademika Tupoleva15, Bld. 2 ("Tupolev Plaza")105005 MoscowPhone: +7 495 980 89 67Fax: +7 495 980 89 67E-Mail: [email protected]

South AfricaReinhausen South Africa (Pty) Ltd.No. 15, Third Street, Booysens ReserveJohannesburgPhone: +27 11 8352077Fax: +27 11 8353806E-Mail: [email protected] South KoreaReinhausen Korea Ltd.21st floor, Standard Chartered Bank Bldg.,47, Chongro, Chongro-gu,Seoul 110-702Phone: +82 2 767 4909Fax: +82 2 736 0049E-Mail: [email protected]

U.S.A.Reinhausen Manufacturing Inc.2549 North 9th AvenueHumboldt, TN 38343Phone: +1 731 784 7681Fax: +1 731 784 7682E-Mail: [email protected] United Arab EmiratesReinhausen Middle East FZEDubai Airport Freezone, Building Phase 63rd floor, Office No. 6EB, 341 DubaiPhone: +971 4 2368 451Fax: +971 4 2368 225Email: [email protected]

Maschinenfabrik Reinhausen GmbHFalkensteinstrasse 893059 Regensburg

+49 (0)941 4090-0+49(0)941 [email protected]

www.reinhausen.com

4489615/01 EN ▪ 02/16 ▪

motor-drive unit tapmotion® td ism® · 2018. 1. 17. · the tapmotion® td ism® motor-drive...

Documents