moyaproof ws2.pdf
TRANSCRIPT
Technical Datasheet
Construction Chemicals
MoyaProof WS2TWO COMPONENT POLYMER MODIFIED SEMI FLEXIBLE CEMENTITIOUSWATERPROOFING MEMBRANEDESCRIPTION MoyaProof WS2 is a two component acrylic co-polymer based flexible
cementitious waterproofing slurry coat. It is supplied in ready to use kit.MoyaProof WS2 provides excellent adhesion, flexibility, and durability.
STANDARDS BS 6920:Part 1:2000, BS 6920:Part 3 : 1996,ASTM C190, ASTM C348, ASTMC241, ASTM C140, BS 1881 : Part 207
USES MoyaProof WS2 is suitable for many waterproofing applications, such asswimming pools, balconies, bathrooms, wet areas, basements and as aeconomical roof waterproofing system in damp conditions where othersystems cannot be used.
ADVANTAGES • Excellent adhesion• Can be applied to freshly hardened concrete• Breathable coating• Protection against carbonation and chlorides• Crack bridging and sealing• Excellent elongation and flexibility• Increased frost & salt resistance• Easy to apply• Minimum surface preparation needed• Excellent for damp-proofing basements• Can be used for potable water tanks
TYPICAL PROPERTIES @ 25°C Appearance : Grey / Off WhiteMix Density : 2.00 kg/ltrPot life : 30 minutesElongation : >40%Adhesion to Concrete : 1.5 N/mm2
Tensile Strength : 2 N/mm2
Water Absorption : <2%Application Temperature : +5°C to +40°CToxicity : Non toxic
SURFACE PREPARATION Surface should be clean and sound, free of dust, loose particles, grease, oil,primers from previous membrane systems or bitumen. Bitumen or primersshould be removed by shotblasting or mechanical means. Spalled concreteshould be repaired by cutting to sound concrete and patching with ReCon GP.
Special recommendations for critical areas of application:
It is recommended to use Conmix ConTape at all critical areas such asintersections, corner joints, floor/wall junctions, gaps (where there is anexpected structural / thermal movements), peripherial areas of pipelines beforethe application of waterproofing membrane to ensure better waterproofing tostructures like swimming pool, balconies, toilets, terrace slab etc... Beforefixing the Conmix ConTape, the gaps and corners should be filled and levelledwith polymer modified mortar (ReCon GP).
CC/MP04/Ver3/12/07
1/2
Construction ChemicalsConstruction Chemicals
Conmix Ltd.P.O. Box 5936 Sharjah,United Arab Emirates Sales OfficeTel: +971 (06) 5314155 Tel: +971 (06) 5682422Fax: +971 (06) 5314332 Fax: +971 (06) 5681442www.conmix.com Email: [email protected]
It is the customer’s responsibility to satisfy themselves by checking with the company that the information is still current at the time of use. The customer must be satisfied that the product is suitablefor the use intended. All products comply with the properties shown on current data sheets. Conmix however do not warrant or guarantee the installation of the products as it does not have any controlover installation or end use of the product. All information and in particular the recommendations relating to application and end use are given in good faith. The products are guaranteed against anydefect and are manufactured and sold subject to Conmix standard terms and conditions of sale.
MIXING MoyaProof WS2 is supplied in premeasured units. Slowly add powder to theliquid and mix to a lump free smooth consistency. Do not add water or reworka stiffened mix by adding water. Mix sufficient material to use within 30-40minutes.
APPLICATION Saturate the concrete surface with clean water. Apply the first coat while thesurface is still damp with no free standing water. Apply using a short stiffbristle brush or roller at a minimum thickness of 1.0 mm per coat. Leave for2-6 hours, apply second coat in perpendicular direction to the first coat. Thesecond coat can be finished by rubbing down with a soft sponge. Spray ortrowel application is acceptable provided the mixing ratio is adjusted to achievethe right consistency. It is recommended that the application over hollowblocks or highly porous areas to be coated with minimum 3 coats at totalthickness of 3mm.
YIELD 12.5 litre / set.
COVERAGE 6 m2 / Set @ 2mm thickness in two coats
CURING MoyaProof WS2 should be protected from high wind & intense sunshine.Keep moist for 3 - 4 days after application. Protect from wind, heat and rainuntil fully cured.
GENERAL INFORMATION Shelf Life 12 months from date of production, if stored properly inoriginal unopened packing in dry conditions and away fromsunlight and scorching heat.
Packaging Part A + B = 25 kg Set.
Cleaning Clean all equipments and tools with water.
Note Stir Well Before Use.
HEALTH & SAFETY PPE’s Gloves, goggles & mask must be worn
Precautions Contact with skin, eyes, etc. must be avoided, if notmay cause irritation
Hazardous It is regarded as non-hazardous for transportation
Disposal Do not re-use bags & containers. To be disposed offas per local rules and regulations.
Detail Information Refer MSDS for detailed information.
TECHNICAL SERVICE Conmix Technical services are available on request for on site support toassist the correct use of it’s products.
CC/MP04/Ver3/12/07
2/2