msh adjustable strap hangers - mitek...msh adjustable strap hangers mitek supplies quality products...
TRANSCRIPT
MSH Adjustable Strap Hangers
MiTek supplies quality productsto build Stronger Safer Structures
MiTek.ca
Use in conjunction with MiTek’s current Canadian Structural Products Catalogue for detailed hanger information.
Copyright © 2019 MiTek Industries, Inc. All Rights Reserved. June 2019 USP2320 MSH
Nailer Options – chart represents maximum factored resistance for hangers used on wood nailers.
Lbs kN Lbs kN
Qty Type Qty Type2X 4 10d x 1-1/2 4 10d x 1-1/2 2045 9.10 1655 7.363X 4 10d x 1-1/2 4 10d x 1-1/2 2045 9.10 1655 7.36
(2) 2X 6 10d 4 10d x 1-1/2 3200 14.23 2635 11.724X 6 10d 4 10d x 1-1/2 3200 14.23 2635 11.722X 6 10d x 1-1/2 6 10d x 1-1/2 3215 14.30 2525 11.233X 6 10d x 1-1/2 6 10d x 1-1/2 3215 14.30 2525 11.23
(2) 2X 6 16d x 2-1/2 6 10d x 1-1/2 3215 14.30 2525 11.234X 6 16d x 2-1/2 6 10d x 1-1/2 3215 14.30 2525 11.23
1) Listed loads shall not be increased. 2) The nailer must be sized to fit the supported width and be of sufficient thickness to satisfy specified top flange nailing requirements. A design professional must specify nailer attachment to steel beams. 3) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d x 2-1/2 nails are 0.162" dia. x 2-1/2" long.
MSH (18GA)
MSH (16GA or 14GA)
Fastener Schedule3 DF Factored Resistance1 S-P-F Factored Resistance1
MiTekSeries
Nailer
Size2
Header Joist
Vertical100%
Vertical100%
Vertical100%
Vertical100%
1) Listed loads shall not be increased.
2) The nailer must be sized to fit the supported width and be of sufficient thickness to satisfy specified top flange nailing requirements. A design professional must specify nailer attachment to steel beams.
3) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d x 2-1/2 nails are 0.162" dia. x 2-1/2" long.
The MSH is field adjustable. The flanges can be used in top mount, face mount, or combination installations. An open back design allows installation after a member is placed in position.
Materials: See chartFinish: G90 galvanizingOptions: See current catalogue for optionsCodes: Load values are derived from data submitted to various North American building code evaluators.
Installation:• Use all specified fasteners. MSH
H
D
W
B
Face Max
All header nails used should be driven into the wide face of the header
Top-Max
The hanger is installed in a topmount condition with at least six lowest header face nail holes filled, and four top flange nails filled. Refer to Table 1 below for minimum top flange length requirements.
Top-Min
The hanger is installed in a top mount condition with at least the top two header face nail holes filled, and four top flange nail holes filled. Refer to Table 1 below for minimum top flange length requirements. The joist nails shall be installed straight into the joist for all models.
Combination Face-Max / Top-Max
Face-Max values apply for the entire connection. Follow fastening directions for the applicable mounting condition for each individual flange strap.
Typical MSH face-max installation
Typical MSH top-max installation
Typical MSH top-min installation
Typical MSH combination installation
Mounting Conditions
Table 1
7/8" 1-1/8" 1-1/2" 1-3/4" 2" 2-3/16" 2-5/8" 2-3/4" 2-13/16"MSH426 MSH29 MSH422-2 MSH426-2 MSH424 MSH222 MSH218-2 MSH218 MSH213
MSH426IF -- MSH422-2IF -- -- MSH322 -- MSH413 ---- -- -- -- -- MSH222-2 -- MSH418 ---- -- -- -- -- MSH422IF -- MSH422 --
1) Total hanger height will be reduced by the top flange length. Carried member height must be accounted for accordingly.
Minimum Top Flange Length for Top Mount Installations 1
Page 1 of 2
Valid through Dec. 31, 2020
June 18, 2019
MSH Adjustable Strap Hangers
MiTek supplies quality productsto build Stronger Safer Structures
MiTek.ca
Use in conjunction with MiTek’s current Canadian Structural Products Catalogue for detailed hanger information.
Copyright © 2019 MiTek Industries, Inc. All Rights Reserved. June 2019 USP2320 MSH
Double shear nail designfeatures fewer nails
and faster installation
Uses standard length nails
MSH426MSH422IF
D
22"
3-5/8"
MSH222
23"
1-5/8"D
H
D
B
W
Top Face
W H D B Qty Qty Type Qty Typeface-max -- 18 10d 4 10d x 1-1/2 4625 1435 20.57 6.38 3630 1125 16.15 5.00top-max 4 6 10d 4 10d x 1-1/2 4785 1435 21.28 6.38 3760 1125 16.73 5.00top-min 4 2 10d 4 10d x 1-1/2 3630 -- 16.15 -- 2850 -- 12.68 --
face-max -- 20 10d 4 10d 4625 1435 20.57 6.38 3630 1125 16.15 5.00top-max 4 6 10d 4 10d 4785 1435 21.28 6.38 3760 1125 16.73 5.00top-min 4 2 10d 4 10d x 1-1/2 3630 -- 16.15 -- 2850 -- 12.68 --
face-max -- 26 10d 4 10d x 1-1/2 4625 1435 20.57 6.38 3630 1125 16.15 5.00top-max 4 6 10d 4 10d x 1-1/2 4785 1435 21.28 6.38 3760 1125 16.73 5.00top-min 4 2 10d 4 10d x 1-1/2 3630 -- 16.15 -- 2850 -- 12.68 --
face-max -- 22 10d 4 10d x 1-1/2 3640 1085 16.19 4.83 2860 850 12.72 3.78top-max 4 6 10d 4 10d x 1-1/2 4125 1085 18.35 4.83 3235 850 14.39 3.78top-min 4 2 10d 4 10d x 1-1/2 3440 -- 15.30 -- 2700 -- 12.01 --
face-max -- 22 10d 4 10d x 1-1/2 3410 940 15.17 4.18 2900 800 12.90 3.56top-max 4 6 10d 4 10d x 1-1/2 4495 975 19.99 4.34 3660 795 16.28 3.54top-min 4 2 10d 4 10d x 1-1/2 3370 -- 14.99 -- 2750 -- 12.23 --
face-max -- 16 10d 4 10d 3940 1105 17.53 4.92 3090 865 13.75 3.85top-max 4 6 10d 4 10d 5530 1105 24.60 4.92 4340 865 19.31 3.85top-min 4 2 10d 4 10d 3425 -- 15.24 -- 2690 -- 11.97 --
face-max -- 22 10d 4 10d 5335 1105 23.73 4.92 4190 865 18.64 3.85top-max 4 6 10d 4 10d 5530 1105 24.60 4.92 4340 865 19.31 3.85top-min 4 2 10d 4 10d 3425 -- 15.24 -- 2690 -- 11.97 --
face-max -- 14 10d 6 10d 5505 2865 24.49 12.74 4320 2250 19.22 10.01top-max 4 6 10d 6 10d 5125 2865 22.80 12.74 4020 2250 17.88 10.01top-min 4 2 10d 6 10d 3215 -- 14.30 -- 2525 -- 11.23 --
face-max -- 18 10d 6 10d 6930 2865 30.83 12.74 5440 2250 24.20 10.01top-max 4 6 10d 6 10d 5125 2865 22.80 12.74 4020 2250 17.88 10.01top-min 4 2 10d 6 10d 3215 -- 14.30 -- 2525 -- 11.23 --
face-max -- 22 10d 6 10d 6015 2490 26.76 11.08 5115 2115 22.75 9.41top-max 4 6 10d 6 10d 5125 2865 22.80 12.74 4020 2250 17.88 10.01top-min 4 2 10d 6 10d 3215 -- 14.30 -- 2525 -- 11.23 --
face-max -- 22 10d 4 10d 5335 1105 23.73 4.92 4190 865 18.64 3.85top-max 4 6 10d 4 10d 5530 1105 24.60 4.92 4340 865 19.31 3.85top-min 4 2 10d 4 10d 3425 -- 15.24 -- 2690 -- 11.97 --
face-max -- 36 10d 6 10d 6285 2345 27.96 10.43 4935 1840 21.95 8.18top-max 4 6 10d 6 10d 4705 2345 20.93 10.43 3695 1840 16.44 8.18top-min 4 2 10d 6 10d 2455 -- 10.92 -- 1930 -- 8.59 --top-max 4 8 16d 6 16d 6115 3415 27.20 15.19 4800 2685 21.35 11.94top-min 4 2 16d 6 16d 4340 905 19.31 4.03 3405 710 15.15 3.16face-max -- 26 16d 6 16d 9025 1935 40.15 8.61 7355 1575 32.72 7.01
top-max 4 10 16d 6 16d 7275 2145 32.36 9.54 5710 1685 25.40 7.50
top-min 4 4 16d 6 16d 6665 -- 29.65 -- 5230 -- 23.26 --
face-max -- 22 10d 4 10d 9025 1935 40.15 8.61 7355 1575 32.72 7.01
top-max 4 6 10d 4 10d 7275 2145 32.36 9.54 5710 1685 25.40 7.50
top-min 4 4 10d 4 10d 6665 -- 29.65 -- 5230 -- 23.26 --
1) Factored uplift resistances have been increased 15% for short-term loads such as wind and earthquake; reduce for other load durations in accordance with the code. 2) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d nails are 0.162" dia. x 3-1/2" long.
MSH426-2
2 11
14 7-1/4 26-1/16 2 11
MSH29 18
14 7-1/4 22-1/8
MSH218 18
MSH222 18 1-5/8
MSH218-2 16
MSH418
MSH222-2 16
16
MSH413 16
MSH422-2 MSH422-2IF
8
MSH424 16 3-5/8 21-1/2 2
MSH426 MSH426IF
14 3-5/8 26 1-3/4
5-3/16
5
1-5/8 2-1/4 516-3/4
3-9/16 17-1/2 1-3/4 7-5/8
10-1/16
1-3/4 10-3/8
10-1/16
1-3/4 10-13/16
3-1/8 17-3/4 1-3/4
7-5/8
3-1/8 22-1/4 1-3/4
3-9/16 14
7-5/8
MSH422IF 16 3-5/8 22 1-3/4 9-13/16
MSH422 16 3-9/16 21-1/2 1-3/4
1-3/4
S-P-F Factored Resistance
Uplift1
115%
MSH322 18 2-9/16 22-1/2
12-3/4
2-1/4 5
MSH213 18 1-5/8 2-1/4
8-3/4
23
1-5/8
MiTekStock No.
MountingCondition
Vertical100%
Uplift1
115%Ga.
Dimensions (in) Fastener Schedule2 DF Factored Resistance
Header Joist Lbs kN Lbs kN
Vertical100%
Uplift1
115%Vertical100%
Vertical100%
Uplift1
115%
Page 2 of 2
Valid through Dec. 31, 2020
June 18, 2019
MSH Adjustable Strap Hangers
MiTek supplies quality productsto build Stronger Safer Structures
MiTek.ca
Use in conjunction with MiTek’s current Canadian Structural Products Catalogue for detailed hanger information.
Copyright © 2019 MiTek Industries, Inc. All Rights Reserved. June 2019 USP2320 MSH
Nailer Options – chart represents maximum factored resistance for hangers used on wood nailers.
Lbs kN Lbs kN
Qty Type Qty Type2X 4 10d x 1-1/2 4 10d x 1-1/2 2045 9.10 1655 7.363X 4 10d x 1-1/2 4 10d x 1-1/2 2045 9.10 1655 7.36
(2) 2X 6 10d 4 10d x 1-1/2 3200 14.23 2635 11.724X 6 10d 4 10d x 1-1/2 3200 14.23 2635 11.722X 6 10d x 1-1/2 6 10d x 1-1/2 3215 14.30 2525 11.233X 6 10d x 1-1/2 6 10d x 1-1/2 3215 14.30 2525 11.23
(2) 2X 6 16d x 2-1/2 6 10d x 1-1/2 3215 14.30 2525 11.234X 6 16d x 2-1/2 6 10d x 1-1/2 3215 14.30 2525 11.23
1) Listed loads shall not be increased. 2) The nailer must be sized to fit the supported width and be of sufficient thickness to satisfy specified top flange nailing requirements. A design professional must specify nailer attachment to steel beams. 3) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d x 2-1/2 nails are 0.162" dia. x 2-1/2" long.
MSH (18GA)
MSH (16GA or 14GA)
Fastener Schedule3 DF Factored Resistance1 S-P-F Factored Resistance1
MiTekSeries
Nailer
Size2
Header Joist
Vertical100%
Vertical100%
Vertical100%
Vertical100%
1) Listed loads shall not be increased.
2) The nailer must be sized to fit the supported width and be of sufficient thickness to satisfy specified top flange nailing requirements. A design professional must specify nailer attachment to steel beams.
3) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d x 2-1/2 nails are 0.162" dia. x 2-1/2" long.
The MSH is field adjustable. The flanges can be used in top mount, face mount, or combination installations. An open back design allows installation after a member is placed in position.
Materials: See chartFinish: G90 galvanizingOptions: See current catalogue for optionsCodes: Load values are derived from data submitted to various North American building code evaluators.
Installation:• Use all specified fasteners. MSH
H
D
W
B
Face Max
All header nails used should be driven into the wide face of the header
Top-Max
The hanger is installed in a topmount condition with at least six lowest header face nail holes filled, and four top flange nails filled. Refer to Table 1 below for minimum top flange length requirements.
Top-Min
The hanger is installed in a top mount condition with at least the top two header face nail holes filled, and four top flange nail holes filled. Refer to Table 1 below for minimum top flange length requirements. The joist nails shall be installed straight into the joist for all models.
Combination Face-Max / Top-Max
Face-Max values apply for the entire connection. Follow fastening directions for the applicable mounting condition for each individual flange strap.
Typical MSH face-max installation
Typical MSH top-max installation
Typical MSH top-min installation
Typical MSH combination installation
Mounting Conditions
Table 1
7/8" 1-1/8" 1-1/2" 1-3/4" 2" 2-3/16" 2-5/8" 2-3/4" 2-13/16"MSH426 MSH29 MSH422-2 MSH426-2 MSH424 MSH222 MSH218-2 MSH218 MSH213
MSH426IF -- MSH422-2IF -- -- MSH322 -- MSH413 ---- -- -- -- -- MSH222-2 -- MSH418 ---- -- -- -- -- MSH422IF -- MSH422 --
1) Total hanger height will be reduced by the top flange length. Carried member height must be accounted for accordingly.
Minimum Top Flange Length for Top Mount Installations 1
Page 1 of 2
Valid through Dec. 31, 2020
June 18, 2019
June 18, 2019
June 18, 2019
June 18, 2019
MSH Adjustable Strap Hangers
MiTek supplies quality productsto build Stronger Safer Structures
MiTek.ca
Use in conjunction with MiTek’s current Canadian Structural Products Catalogue for detailed hanger information.
Copyright © 2019 MiTek Industries, Inc. All Rights Reserved. June 2019 USP2320 MSH
Double shear nail designfeatures fewer nails
and faster installation
Uses standard length nails
MSH426MSH422IF
D
22"
3-5/8"
MSH222
23"
1-5/8"D
H
D
B
W
Top Face
W H D B Qty Qty Type Qty Typeface-max -- 18 10d 4 10d x 1-1/2 4625 1435 20.57 6.38 3630 1125 16.15 5.00top-max 4 6 10d 4 10d x 1-1/2 4785 1435 21.28 6.38 3760 1125 16.73 5.00top-min 4 2 10d 4 10d x 1-1/2 3630 -- 16.15 -- 2850 -- 12.68 --
face-max -- 20 10d 4 10d 4625 1435 20.57 6.38 3630 1125 16.15 5.00top-max 4 6 10d 4 10d 4785 1435 21.28 6.38 3760 1125 16.73 5.00top-min 4 2 10d 4 10d x 1-1/2 3630 -- 16.15 -- 2850 -- 12.68 --
face-max -- 26 10d 4 10d x 1-1/2 4625 1435 20.57 6.38 3630 1125 16.15 5.00top-max 4 6 10d 4 10d x 1-1/2 4785 1435 21.28 6.38 3760 1125 16.73 5.00top-min 4 2 10d 4 10d x 1-1/2 3630 -- 16.15 -- 2850 -- 12.68 --
face-max -- 22 10d 4 10d x 1-1/2 3640 1085 16.19 4.83 2860 850 12.72 3.78top-max 4 6 10d 4 10d x 1-1/2 4125 1085 18.35 4.83 3235 850 14.39 3.78top-min 4 2 10d 4 10d x 1-1/2 3440 -- 15.30 -- 2700 -- 12.01 --
face-max -- 22 10d 4 10d x 1-1/2 3410 940 15.17 4.18 2900 800 12.90 3.56top-max 4 6 10d 4 10d x 1-1/2 4495 975 19.99 4.34 3660 795 16.28 3.54top-min 4 2 10d 4 10d x 1-1/2 3370 -- 14.99 -- 2750 -- 12.23 --
face-max -- 16 10d 4 10d 3940 1105 17.53 4.92 3090 865 13.75 3.85top-max 4 6 10d 4 10d 5530 1105 24.60 4.92 4340 865 19.31 3.85top-min 4 2 10d 4 10d 3425 -- 15.24 -- 2690 -- 11.97 --
face-max -- 22 10d 4 10d 5335 1105 23.73 4.92 4190 865 18.64 3.85top-max 4 6 10d 4 10d 5530 1105 24.60 4.92 4340 865 19.31 3.85top-min 4 2 10d 4 10d 3425 -- 15.24 -- 2690 -- 11.97 --
face-max -- 14 10d 6 10d 5505 2865 24.49 12.74 4320 2250 19.22 10.01top-max 4 6 10d 6 10d 5125 2865 22.80 12.74 4020 2250 17.88 10.01top-min 4 2 10d 6 10d 3215 -- 14.30 -- 2525 -- 11.23 --
face-max -- 18 10d 6 10d 6930 2865 30.83 12.74 5440 2250 24.20 10.01top-max 4 6 10d 6 10d 5125 2865 22.80 12.74 4020 2250 17.88 10.01top-min 4 2 10d 6 10d 3215 -- 14.30 -- 2525 -- 11.23 --
face-max -- 22 10d 6 10d 6015 2490 26.76 11.08 5115 2115 22.75 9.41top-max 4 6 10d 6 10d 5125 2865 22.80 12.74 4020 2250 17.88 10.01top-min 4 2 10d 6 10d 3215 -- 14.30 -- 2525 -- 11.23 --
face-max -- 22 10d 4 10d 5335 1105 23.73 4.92 4190 865 18.64 3.85top-max 4 6 10d 4 10d 5530 1105 24.60 4.92 4340 865 19.31 3.85top-min 4 2 10d 4 10d 3425 -- 15.24 -- 2690 -- 11.97 --
face-max -- 36 10d 6 10d 6285 2345 27.96 10.43 4935 1840 21.95 8.18top-max 4 6 10d 6 10d 4705 2345 20.93 10.43 3695 1840 16.44 8.18top-min 4 2 10d 6 10d 2455 -- 10.92 -- 1930 -- 8.59 --top-max 4 8 16d 6 16d 6115 3415 27.20 15.19 4800 2685 21.35 11.94top-min 4 2 16d 6 16d 4340 905 19.31 4.03 3405 710 15.15 3.16face-max -- 26 16d 6 16d 9025 1935 40.15 8.61 7355 1575 32.72 7.01
top-max 4 10 16d 6 16d 7275 2145 32.36 9.54 5710 1685 25.40 7.50
top-min 4 4 16d 6 16d 6665 -- 29.65 -- 5230 -- 23.26 --
face-max -- 22 10d 4 10d 9025 1935 40.15 8.61 7355 1575 32.72 7.01
top-max 4 6 10d 4 10d 7275 2145 32.36 9.54 5710 1685 25.40 7.50
top-min 4 4 10d 4 10d 6665 -- 29.65 -- 5230 -- 23.26 --
1) Factored uplift resistances have been increased 15% for short-term loads such as wind and earthquake; reduce for other load durations in accordance with the code. 2) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d nails are 0.162" dia. x 3-1/2" long.
MSH426-2
2 11
14 7-1/4 26-1/16 2 11
MSH29 18
14 7-1/4 22-1/8
MSH218 18
MSH222 18 1-5/8
MSH218-2 16
MSH418
MSH222-2 16
16
MSH413 16
MSH422-2 MSH422-2IF
8
MSH424 16 3-5/8 21-1/2 2
MSH426 MSH426IF
14 3-5/8 26 1-3/4
5-3/16
5
1-5/8 2-1/4 516-3/4
3-9/16 17-1/2 1-3/4 7-5/8
10-1/16
1-3/4 10-3/8
10-1/16
1-3/4 10-13/16
3-1/8 17-3/4 1-3/4
7-5/8
3-1/8 22-1/4 1-3/4
3-9/16 14
7-5/8
MSH422IF 16 3-5/8 22 1-3/4 9-13/16
MSH422 16 3-9/16 21-1/2 1-3/4
1-3/4
S-P-F Factored Resistance
Uplift1
115%
MSH322 18 2-9/16 22-1/2
12-3/4
2-1/4 5
MSH213 18 1-5/8 2-1/4
8-3/4
23
1-5/8
MiTekStock No.
MountingCondition
Vertical100%
Uplift1
115%Ga.
Dimensions (in) Fastener Schedule2 DF Factored Resistance
Header Joist Lbs kN Lbs kN
Vertical100%
Uplift1
115%Vertical100%
Vertical100%
Uplift1
115%
Page 2 of 2
Valid through Dec. 31, 2020
June 18, 2019
June 18, 2019
June 18, 2019
June 18, 2019
MSH Adjustable Strap Hangers
MiTek supplies quality productsto build Stronger Safer Structures
MiTek.ca
Use in conjunction with MiTek’s current Canadian Structural Products Catalogue for detailed hanger information.
Copyright © 2019 MiTek Industries, Inc. All Rights Reserved. June 2019 USP2320 MSH
Nailer Options – chart represents maximum factored resistance for hangers used on wood nailers.
Lbs kN Lbs kN
Qty Type Qty Type2X 4 10d x 1-1/2 4 10d x 1-1/2 2045 9.10 1655 7.363X 4 10d x 1-1/2 4 10d x 1-1/2 2045 9.10 1655 7.36
(2) 2X 6 10d 4 10d x 1-1/2 3200 14.23 2635 11.724X 6 10d 4 10d x 1-1/2 3200 14.23 2635 11.722X 6 10d x 1-1/2 6 10d x 1-1/2 3215 14.30 2525 11.233X 6 10d x 1-1/2 6 10d x 1-1/2 3215 14.30 2525 11.23
(2) 2X 6 16d x 2-1/2 6 10d x 1-1/2 3215 14.30 2525 11.234X 6 16d x 2-1/2 6 10d x 1-1/2 3215 14.30 2525 11.23
1) Listed loads shall not be increased. 2) The nailer must be sized to fit the supported width and be of sufficient thickness to satisfy specified top flange nailing requirements. A design professional must specify nailer attachment to steel beams. 3) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d x 2-1/2 nails are 0.162" dia. x 2-1/2" long.
MSH (18GA)
MSH (16GA or 14GA)
Fastener Schedule3 DF Factored Resistance1 S-P-F Factored Resistance1
MiTekSeries
Nailer
Size2
Header Joist
Vertical100%
Vertical100%
Vertical100%
Vertical100%
1) Listed loads shall not be increased.
2) The nailer must be sized to fit the supported width and be of sufficient thickness to satisfy specified top flange nailing requirements. A design professional must specify nailer attachment to steel beams.
3) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d x 2-1/2 nails are 0.162" dia. x 2-1/2" long.
The MSH is field adjustable. The flanges can be used in top mount, face mount, or combination installations. An open back design allows installation after a member is placed in position.
Materials: See chartFinish: G90 galvanizingOptions: See current catalogue for optionsCodes: Load values are derived from data submitted to various North American building code evaluators.
Installation:• Use all specified fasteners. MSH
H
D
W
B
Face Max
All header nails used should be driven into the wide face of the header
Top-Max
The hanger is installed in a topmount condition with at least six lowest header face nail holes filled, and four top flange nails filled. Refer to Table 1 below for minimum top flange length requirements.
Top-Min
The hanger is installed in a top mount condition with at least the top two header face nail holes filled, and four top flange nail holes filled. Refer to Table 1 below for minimum top flange length requirements. The joist nails shall be installed straight into the joist for all models.
Combination Face-Max / Top-Max
Face-Max values apply for the entire connection. Follow fastening directions for the applicable mounting condition for each individual flange strap.
Typical MSH face-max installation
Typical MSH top-max installation
Typical MSH top-min installation
Typical MSH combination installation
Mounting Conditions
Table 1
7/8" 1-1/8" 1-1/2" 1-3/4" 2" 2-3/16" 2-5/8" 2-3/4" 2-13/16"MSH426 MSH29 MSH422-2 MSH426-2 MSH424 MSH222 MSH218-2 MSH218 MSH213
MSH426IF -- MSH422-2IF -- -- MSH322 -- MSH413 ---- -- -- -- -- MSH222-2 -- MSH418 ---- -- -- -- -- MSH422IF -- MSH422 --
1) Total hanger height will be reduced by the top flange length. Carried member height must be accounted for accordingly.
Minimum Top Flange Length for Top Mount Installations 1
Page 1 of 2
Valid through Dec. 31, 2020
June 18, 2019
June 18, 2019
June 18, 2019
June 18, 2019
MSH Adjustable Strap Hangers
MiTek supplies quality productsto build Stronger Safer Structures
MiTek.ca
Use in conjunction with MiTek’s current Canadian Structural Products Catalogue for detailed hanger information.
Copyright © 2019 MiTek Industries, Inc. All Rights Reserved. June 2019 USP2320 MSH
Double shear nail designfeatures fewer nails
and faster installation
Uses standard length nails
MSH426MSH422IF
D
22"
3-5/8"
MSH222
23"
1-5/8"D
H
D
B
W
Top Face
W H D B Qty Qty Type Qty Typeface-max -- 18 10d 4 10d x 1-1/2 4625 1435 20.57 6.38 3630 1125 16.15 5.00top-max 4 6 10d 4 10d x 1-1/2 4785 1435 21.28 6.38 3760 1125 16.73 5.00top-min 4 2 10d 4 10d x 1-1/2 3630 -- 16.15 -- 2850 -- 12.68 --
face-max -- 20 10d 4 10d 4625 1435 20.57 6.38 3630 1125 16.15 5.00top-max 4 6 10d 4 10d 4785 1435 21.28 6.38 3760 1125 16.73 5.00top-min 4 2 10d 4 10d x 1-1/2 3630 -- 16.15 -- 2850 -- 12.68 --
face-max -- 26 10d 4 10d x 1-1/2 4625 1435 20.57 6.38 3630 1125 16.15 5.00top-max 4 6 10d 4 10d x 1-1/2 4785 1435 21.28 6.38 3760 1125 16.73 5.00top-min 4 2 10d 4 10d x 1-1/2 3630 -- 16.15 -- 2850 -- 12.68 --
face-max -- 22 10d 4 10d x 1-1/2 3640 1085 16.19 4.83 2860 850 12.72 3.78top-max 4 6 10d 4 10d x 1-1/2 4125 1085 18.35 4.83 3235 850 14.39 3.78top-min 4 2 10d 4 10d x 1-1/2 3440 -- 15.30 -- 2700 -- 12.01 --
face-max -- 22 10d 4 10d x 1-1/2 3410 940 15.17 4.18 2900 800 12.90 3.56top-max 4 6 10d 4 10d x 1-1/2 4495 975 19.99 4.34 3660 795 16.28 3.54top-min 4 2 10d 4 10d x 1-1/2 3370 -- 14.99 -- 2750 -- 12.23 --
face-max -- 16 10d 4 10d 3940 1105 17.53 4.92 3090 865 13.75 3.85top-max 4 6 10d 4 10d 5530 1105 24.60 4.92 4340 865 19.31 3.85top-min 4 2 10d 4 10d 3425 -- 15.24 -- 2690 -- 11.97 --
face-max -- 22 10d 4 10d 5335 1105 23.73 4.92 4190 865 18.64 3.85top-max 4 6 10d 4 10d 5530 1105 24.60 4.92 4340 865 19.31 3.85top-min 4 2 10d 4 10d 3425 -- 15.24 -- 2690 -- 11.97 --
face-max -- 14 10d 6 10d 5505 2865 24.49 12.74 4320 2250 19.22 10.01top-max 4 6 10d 6 10d 5125 2865 22.80 12.74 4020 2250 17.88 10.01top-min 4 2 10d 6 10d 3215 -- 14.30 -- 2525 -- 11.23 --
face-max -- 18 10d 6 10d 6930 2865 30.83 12.74 5440 2250 24.20 10.01top-max 4 6 10d 6 10d 5125 2865 22.80 12.74 4020 2250 17.88 10.01top-min 4 2 10d 6 10d 3215 -- 14.30 -- 2525 -- 11.23 --
face-max -- 22 10d 6 10d 6015 2490 26.76 11.08 5115 2115 22.75 9.41top-max 4 6 10d 6 10d 5125 2865 22.80 12.74 4020 2250 17.88 10.01top-min 4 2 10d 6 10d 3215 -- 14.30 -- 2525 -- 11.23 --
face-max -- 22 10d 4 10d 5335 1105 23.73 4.92 4190 865 18.64 3.85top-max 4 6 10d 4 10d 5530 1105 24.60 4.92 4340 865 19.31 3.85top-min 4 2 10d 4 10d 3425 -- 15.24 -- 2690 -- 11.97 --
face-max -- 36 10d 6 10d 6285 2345 27.96 10.43 4935 1840 21.95 8.18top-max 4 6 10d 6 10d 4705 2345 20.93 10.43 3695 1840 16.44 8.18top-min 4 2 10d 6 10d 2455 -- 10.92 -- 1930 -- 8.59 --top-max 4 8 16d 6 16d 6115 3415 27.20 15.19 4800 2685 21.35 11.94top-min 4 2 16d 6 16d 4340 905 19.31 4.03 3405 710 15.15 3.16face-max -- 26 16d 6 16d 9025 1935 40.15 8.61 7355 1575 32.72 7.01
top-max 4 10 16d 6 16d 7275 2145 32.36 9.54 5710 1685 25.40 7.50
top-min 4 4 16d 6 16d 6665 -- 29.65 -- 5230 -- 23.26 --
face-max -- 22 10d 4 10d 9025 1935 40.15 8.61 7355 1575 32.72 7.01
top-max 4 6 10d 4 10d 7275 2145 32.36 9.54 5710 1685 25.40 7.50
top-min 4 4 10d 4 10d 6665 -- 29.65 -- 5230 -- 23.26 --
1) Factored uplift resistances have been increased 15% for short-term loads such as wind and earthquake; reduce for other load durations in accordance with the code. 2) NAILS: 10d x 1-1/2 nails are 0.148" dia. x 1-1/2" long, 10d nails are 0.148" dia. x 3" long, 16d nails are 0.162" dia. x 3-1/2" long.
MSH426-2
2 11
14 7-1/4 26-1/16 2 11
MSH29 18
14 7-1/4 22-1/8
MSH218 18
MSH222 18 1-5/8
MSH218-2 16
MSH418
MSH222-2 16
16
MSH413 16
MSH422-2 MSH422-2IF
8
MSH424 16 3-5/8 21-1/2 2
MSH426 MSH426IF
14 3-5/8 26 1-3/4
5-3/16
5
1-5/8 2-1/4 516-3/4
3-9/16 17-1/2 1-3/4 7-5/8
10-1/16
1-3/4 10-3/8
10-1/16
1-3/4 10-13/16
3-1/8 17-3/4 1-3/4
7-5/8
3-1/8 22-1/4 1-3/4
3-9/16 14
7-5/8
MSH422IF 16 3-5/8 22 1-3/4 9-13/16
MSH422 16 3-9/16 21-1/2 1-3/4
1-3/4
S-P-F Factored Resistance
Uplift1
115%
MSH322 18 2-9/16 22-1/2
12-3/4
2-1/4 5
MSH213 18 1-5/8 2-1/4
8-3/4
23
1-5/8
MiTekStock No.
MountingCondition
Vertical100%
Uplift1
115%Ga.
Dimensions (in) Fastener Schedule2 DF Factored Resistance
Header Joist Lbs kN Lbs kN
Vertical100%
Uplift1
115%Vertical100%
Vertical100%
Uplift1
115%
Page 2 of 2
Valid through Dec. 31, 2020
June 18, 2019
June 18, 2019
June 18, 2019
June 18, 2019