mt tracker bbq™ operating manual€¦ · 06 mt tracker bbq operating manual cylinder setup the...

MT Tracker BBQ™ Operating Manual

Important Notice

This document has been prepared by BOC Limited ABN 95 000 029 729 (‘BOC’), as operating instructions and has been prepared in good faith. Information in this document has been derived from third parties, and though BOC believes it to be reliable as at the time of printing, BOC makes no representation or warranty as to the accuracy, reliability or completeness of information in this document and does not assume any responsibility for updating any information or correcting any error or omission which may become apparent after the document has been issued. The information in this document is commercial in confidence and is not to be reproduced. The recipient acknowledges and agrees that it must make its own independent investigation and should consider seeking appropriate professional advice in reviewing

the information. This document does not take into account the particular circumstances of the recipient. Except insofar as liability under any statute cannot be excluded, BOC and its affiliates, directors, employees, contractors and consultants do not accept any liability (whether arising in contract, tort or otherwise) for any error or omission in this document or for any resulting loss or damage (whether direct, indirect, consequential or otherwise) suffered by the recipient of this document or any other person relying on the information contained herein. The recipient agrees that it shall not seek to sue or hold BOC or their respective agents liable in any such respect for the provision of this document or any other information.

MT Tracker BBQ Operating Manual02

Description 3

Smart device setup 4

Cylinder setup 6

Using the app 7

Battery replacement 10

Warranty 14

Safety guidelines 15

Specifications 16

Troubleshooting tips 17

Contents.

03MT Tracker BBQ Operating Manual

MT Tracker BBQ™ sensor accurately detects LPG cylinder fill levels and sends the status via Bluetooth® to our mobile app. You can also rename sensors, set auto alerts or add multiple sensors. Available for both iOS and Android devices.

Outdoor use only.

Description


Smart device setup

Go to your app store. Search for the Mt Tracker app and install.

Launch the app. When it starts it will automatically start a search for sensors.

The first time you use your MT Tracker BBQ™ press the “Sync” button 5 times in a row to initialise it. Press and hold SYNC button until sensor appears on app. (up to 10 seconds).

No MT Tracker BBQ™ devices have been added.

The first time you use your MT Tracker BBQ™ press the “Sync” button 5 times in a row to initialise it. To add new sensors make sure the scanning icon is spinning

press and hold SYNC button on your MT Tracker BBQ™ until it is found.


The sensor will then appear on your app as a new device. Sensor is now Sync’d. You may now proceed to installing the sensor on the cylinder.


Cylinder setup

The cylinder should be kept upright at all times throughout the installation process. Clean the bottom of the cylinder of any debris, excess paint, and rust.

The sensor mounts to the bottom centre of the cylinder using magnets. The rubber pad between the magnets must make good contact with the cylinder, with no contaminants in between and must be aligned to the bottom centre of the cylinder.

Check that the cylinder is on a level and flat surface or otherwise is level with ground. Even a slight tilt can degrade the quality of the measurement.

After a short period the LPG will settle and the readings will stabilize.

Magnet

MagnetRubber pad


Using the app

Adding more sensors will keep adding to the sensor list. Up to 50 sensors can be added.

Selecting a sensor from the list takes you to the sensor’s info screen that shows the battery condition, Bluetooth signal strength, and detection quality. A low quality level often indicates an installation problem, such as poor placement, debris or excessive paint, etc. which can cause erratic readings.


Selecting the pencil icon will bring up the settings page for the sensor, where you can edit the sensor name, select your cylinder size or enter an arbitrary custom size, set LPG level alarm threshold and level display units.


To remove a sensor from the app list, swipe left on the sensor in the list. A delete button will appear. Select delete to confirm removal of the sensor from the app.


Battery replacement

WARNING: EXPLOSION HAZARD-BATTERIES MUST ONLY BE CHANGED IN AN AREA FREE OF IGNITABLE CONCENTRATIONS.

The enclosure lid is held in place by a snap fit, in 4 places. In the approximate locations shown, insert small screwdriver between lid and base and pry outward to release snap fit. Lid can then be lifted out of assembly. (Note: Sync button will sometimes be slightly stuck to electronics board. Detach sync button and board if necessary to completely remove lid and leave electronics in the base piece.)

Gently lift board from base such that battery can be removed from battery holder. Insert new battery in same orientation. (Note: Wires that connect sensor base and electronics board remain attached during battery change. Use care not pull too hard on wires thus damaging the sensor.)

1

3

2

4


Place electronics board back into base. Pay attention to wire routing so that wires do not get pinched when lid is reassembled. Also check that the enclosure seal is properly seated into the base.

Seal


4. If Sync button came loose during disassembly, assemble button back to lid. Button will stay attached to lid once properly assembled to lid.


6. Place lid back into base and press down fully to reengage all 4 snap fits.


Warranty

The MT Tracker BBQ™ carries a 12 month warranty from the date of purchase. This warranty excludes apparent misuse of the sensor and battery.


Use of this device in a manner other than stated in this manual, may result in impairment of the designed safety protection and thus an unsafe condition.

Safety guidelines


Specifications

SpecificationsPart number GASM1001354

Measurement method Ultrasonic

Fluid LPG

Cylinder types Steel cylindersNote: Also works with aluminum cylinders with alternate mounting. Not intended for use on composite cylinders.

Cylinder sizes Vertical DOT Cylinders of 3.7 kg and 8.5 kg Typically any LPG cylinder up to 500 mm (20”) fluid height, on which the sensor may be mounted on bottom.

Envelope dimensions 47.2 x 87.7 x 7.3 mm (1.85 x 3.45 x 0.29 in)

Mounting location Cylinder bottom

Suitable for these locations CLASS 1, DIVISION 2, GROUP D CLASS 1, ZONE 2, GROUP IIA

Operating temperature range -25° TO 40°C

Temperature code T6

Battery ONE, CR2032 COIN CELL (3 V)

Humidity range 0–100%

Max. altitude 4000 m


Troubleshooting tips

Make sure your cylinder is level. If the cylinder is sitting at an angle, the surface of the liquid will also be at an angle, sometimes causing incorrect readings.

MT Tracker BBQ™ sensor must be located properly. The black rubber contact pad should be placed on centre of the cylinder bottom.

If experiencing a reading that looks incorrect or erratic, sometimes a slight reposition of the sensor will correct the problem.

If the bottom of the cylinder is dirty or rusty it will need to be wiped clean of any debris first. Also the black rubber contact pad on the sensor should be kept clean.

If the cylinder is moving or vibrating it will degrade the quality of the signal.

Movement of the cylinder can cause the liquid to slosh, sometimes causing erratic readings. Readings should go back to normal after a few minutes.

It’s typical to see the level change slightly with changing temperature. This is a characteristic of LPG as it boils into gas.

MT Tracker BBQ™ sensor is shipped in sleep mode to preserve battery life. You must press the Sync button on the sensor at least 5 times to wake it up before it will be detected.

BOC Limited 10 Julius Avenue, North Ryde NSW 2113, Australia970–988 Great South Road, Penrose, Auckland, New Zealand

MP1

8-00

89 F

DAUS

081

8

© BOC Limited 2018. BOC is a trading name of BOC Limited, a Member of The Linde Group. Reproduction without permission is strictly prohibited. Details given in this document are believed to be correct at the time of printing. Whilst proper care has been taken in the preparation, no liability for injury or damage resulting from its improper use can be accepted.

For more information contact the BOC Customer Service Centre.

BOC Australia 131 262 www.boc.com.au

BOC New Zealand 0800 111 333 www.boc.co.nz

mt tracker bbq™ operating manual€¦ · 06 mt tracker bbq operating manual cylinder setup the...

Documents