mt01_assembly_04
DESCRIPTION
Broken lines of assembly because coloring becomes more difficult *Take care when using sharp or pointed objects or when may be differences in dimensions, depending on the once parts are assembled. *Occasionally, white spots will be apparent on folds It is recommended that this be done after each stage *Follow the working method and markings carefully. tool to make a light crease along the dotted or solid line. This will make the folds straight. Avoid making under the paper you want to cut. 2TRANSCRIPT
Please glue them by aligning the red and red/blue and blueparts if they are marked on the paper.
2
Note
Basic working method and markingsTo begin
How to assemble
Tools and materials needed
Items of Caution
-Ruler - scissors - blade cutter or "Exacto-knife" - awl or
other pointed tool (for making a folding crease) - felt pen
- pin set - glue - hand towel ( for cleaning your fingers) -
dictionary or other heavy book ( to press the papers flat).
*Take care when using sharp or pointed objects or when
using bladed cutting tools. Place a heavy sheet of paper
under the paper you want to cut.
*Use glue and other adhesives only in well-ventilated
areas.
*When printing, use a slightly reduced font size. There
may be differences in dimensions, depending on the
type of printer used.
*Follow the working method and markings carefully.
*Cut carefully along the outter line with cutting blade,
Exacto-knife or scissors.
One - point Advice
*Before beginning assembly, test adhesive amounts
on extra paper.
*Cut carefully with cutting blade, Exacto-knife or
scissors.
*Occasionally, white spots will be apparent on folds
and cuts. Use a marker or pencil to fill in these spots.
It is recommended that this be done after each stage
of assembly because coloring becomes more difficult
once parts are assembled.
*As an adhesive, white wood glue is recommended.
Avoid over application as this may cause the paper to
wrinkle.
*For folding parts, first use an awl or other pointed
tool to make a light crease along the dotted or solid
line. This will make the folds straight. Avoid making
strong creases, as this will cause the paper to tear.
Cut along these lines.Dotted line
Fold along these lines. The printed surface should beon the inside of the folded shape.
Broken lines
Fold along these lines. The printed surface should beon the outside of the folded shape.
Solid lines
Do not fold or cut the partsmarked .
Red dots are the referencepositions for gluing surfaces.
Cut out parts marked with anasterisk(*).
3
Indication of Working Methods
First, assemble each component by following the working
method and markings. Then, refer to the illustration and
photos below to glue the parts together.
Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
Foldor Curve Glue
8 Assembling the Exhaust Pipes
Exhaust Pipes 1Sheet H, 18 parts in total
Exhaust Pipes2Sheet H, 8 parts in total
Reference photo
Reference photo
1
2
3
4
5
6
6
1
2
3
4
56
7
8
*Assemble both sides. The diagram shows the left side. The number inside the ( ) is for the right side.
Glue in order from to on the graphic.1 8
Glue in order from to on the graphic.1 6
* Do not paste H-19 & H-20.
H-5(10)
H-6(11)
H-7(12)
H-1(15)
H-2(16)
H-3(17)
H-4(18)
H-9(14)
H-8(13)
H-22
H-21
H-24
H-26
H-23
H-19H-25
H-20
4
Exhaust Pipes5Sheet H, 12 parts in total
Exhaust Pipes4Sheet H, 6 parts in total
Exhaust Pipes3Sheet H, 9 parts in total
Indication of Working Methods
First, assemble each component by following the working
method and markings. Then, refer to the illustration and
photos below to glue the parts together.
Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
Foldor Curve Glue
8 Assembling the Exhaust Pipes
Reference photo
Reference photo
Reference photo
Glue in order from to on the graphic.1
12
3
456
7
1
2
3
4
5
6
7
8
9
10
7
*Assemble both sides. The diagram shows the left side. The number inside the ( ) is for the right side.
Glue in order from to onthe graphic.
1 10
* Do not paste H-29 & H-30.
H-28 H-29
H-27
H-30
H-31
H-32
H-42
H-53H-47
H-46
H-45
H-44
H-43
H-52
H-51
H-50
H-49
H-48
H-33
H-34
H-35
H-36(39)
H-38(41)
H-37(40)
5
Exhaust PipesSheet H, 53 parts in total
Indication of Working Methods
First, assemble each component by following the working
method and markings. Then, refer to the illustration and
photos below to glue the parts together.
Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
Foldor Curve Glue
8 Assembling the Exhaust Pipes
Reference photo
Connect each of the previously assembled parts in order from - according to the diagram.1
12
2
* Do not paste on exhaust pipes.
* Do not paste on exhaust pipes.
Exhaust Pipes1
Exhaust Pipes1
Exhaust Pipes2
Exhaust Pipes2
Exhaust Pipes3
Exhaust Pipes3
Exhaust Pipes4
Exhaust Pipes4
Exhaust Pipes5
* Do not paste Exhaust Pipes1 & Exhaust Pipes4.
* Do not paste Exhaust Pipes4 & Exhaust Pipes5.
6
Indication of Working Methods
First, assemble each component by following the working
method and markings. Then, refer to the illustration and
photos below to glue the parts together.
Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
Foldor Curve Glue
9 Assembling the Seat
SeatSheet I, 8 parts in total
Reference photo
Connect each of the previously assembled parts in order from - according to the diagram.1
1
2
3
4
5
6
6
6
7
7
7
8
8
8
8
I-5
I-8
I-7
I-3
I-1
I-6
I -4
I -2
7
Left footrests1Sheet J, 5 parts in total
Right footrests2Sheet K, 5 parts in total
Indication of Working Methods
First, assemble each component by following the working
method and markings. Then, refer to the illustration and
photos below to glue the parts together.
Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
Foldor Curve Glue
10 Assembling the right and left footrests
Right footrests3Sheet K, 10 parts in total
Reference photo
Reference photo
Reference photoGlue in order from to on the graphic.1
Glue in order from to on the graphic.1
1
1
2
2
3
3
4
4
56
7 8
9
4
9
K-17K-20
K-1
K-4
K-2
K-3
J-11
J-12
J-15
K-15K-18
K-21
K-19
K-16
K-14
K-13
K-12
K-5
J-13
J-14
8
Indication of Working Methods
First, assemble each component by following the working
method and markings. Then, refer to the illustration and
photos below to glue the parts together.
Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
Foldor Curve Glue
10 Assembling the right and left footrests
Left footrestsSheet J, 15 parts in total
Reference photo
1
Connect each of the previously assembled parts in order from - according to the diagram.1
2
3
4
5
6
7
8
9
10
10
Left footrests1
J-10
J-2
J-3 J-4 J-5
J-9
J-1
J-8
J-6
J-7
9
Indication of Working Methods
First, assemble each component by following the working
method and markings. Then, refer to the illustration and
photos below to glue the parts together.
Fold each relevant part according to the assembly symbols.
Please use the dots on each component as reference when gluing surfaces.
Foldor Curve Glue
10 Assembling the right and left footrests
Right footrestsSheet K, 22 parts in total
Reference photo
Connect each of the previously assembled parts in order from - according to the diagram.1
1
2
3
4
5
6
6
6
7
7
Right footrests3Right footrests2
K-11
K-8
K-10
K-9
K-7
K-6