MTS-1700 SERIES

ADVANCED UNIVERSAL

PROTECTIVE RELAY

TEST SYSTEM

TESTS ALL TYPES OF PROTECTIVE RELAYS

DYNAMIC TESTING

EASY-TO-USE

PRODUCTIVITY ENHANCING FEATURES

DIRECT DISPLAY OF RELAY PARAMETERS: FAULT ANGLE,

IMPEDANCE, SLOPE, POWER

TRANSIENT WAVEFORM PLAYBACK CAPABLE

HIGH COMPLIANCE VOLTAGE, HIGH VA CURRENT OUTPUT

PERFORM SIMPLE AND COMPLEX TASKS MANUALLY

PARALLELABLE CURRENT OUTPUT CHANNELS

UNMATCHED VERSATILITY

COMPACT & PORTABLE

COVERS THE COMPLETE SPECTRUM OF RELAY TESTING .....

Steady state testing

Dynamic testing

Dynamic with controlled source impedance

Scheme testing

Harmonic sensitivity

Fault waveform playback

Automated testing

End-to-end testing

MTS-1700 Series

APPLICATIONS

Test, evaluation, calibration and commissioning of all protective relays including:

FUNCTION ANSI NO. FUNCTION ANSI NO.

Under/Overcurrent 50/51 Impedance 21Under/Overvoltage 27 Loss of field 40Frequency 81 DC auxiliary 94Frequency rate of change 81 Motor protection N/AVolts per Hertz 24 Negative sequence 46Transformer differential 87 Line differential 87Directional overcurrent 67 Pilot protection N/ASynchronizing 25 Reclosing 79Directional Power 32 Out of step 78Breaker failure 50BF Multi-function distance N/AStator ground 59N/27TN Voltage balance 60FL

Secondary injection testing of protection & metering panelsTesting of voltage, current, power, frequency, phase angle transducers, energy meters Testing of fault locators and fault recorders

2

Features & Benefits

DISTINCTIVE FEATURES

· Independently programmable prefault, fault and postfault settings· 12 built-in fault mode setups - simulate classical faults· Single knob adjustment of multiphase parameters· Programmable fault incidence angle· Easy to use, setting-free timer· Programmable ramping/fault duration· Independent variable DC voltage output· DC current output for testing DC current operated targets· Direct % harmonic adjustment· Front panel menu gives access to many programmable capabilities· Dual frequency mode for testing synchronizing devices· Two wire pulse timing· External current input for extra-high burden relays· All functions are automated using MTS-1780 or other software· Multi-system synchronization· Auxiliary communication port connects to relay/device under test· Closed case calibration· Extended warranty & full service agreements offered

Integrated, setting-free timer

Independently programmable prefault, fault and postfault conditions

External current inputmode for extra high

burden relays

Convenient fault type &phase selector

DC coupled outputsfor transient playback

Dedicated DC voltageoutput channel

Single phase 2-wire,2 channel 4 wire, or

3 phase 4 wire current output

THE CHOICE OF THE EXPERTS

High performance and unmatchedversatility are some of the manyreasons why the experts choose theMTS-1700 series Advanced UniversalProtective Relay Test System.

Many advanced capabilities suchas ramping and computed

measurements

Unique �Powerscope� software gives realtime phasor display of outputs, impedanceand symmetrical components.

3

�The portability of the MTS-1710 injectiontest set has played a key role in many ofour commissioning projects.�Ross PottageSupervisor of Technical Services

MTS-1710 Advanced UniversalProtective Relay Test System

Basic Facts· Configurable as 3-phase voltage + single

phase current OR 2 voltages + 2 currents· Dedicated DC voltage channel output· Able to test all single phase devices, differential

devices and most 3-phase devices· Autoranging seconds/cycles timer· Many integrated control and measurement

functions

The MTS-1710 meets the needs of virtually allprotection relay testing work in one package.Manual and remote control is provided allowingadjustment of the parameters required tosimulate virtually any condition required (eg.voltage, current, phase angle, frequency, faultdurations, breaker time, etc.).

SINGLE PHASE AND 3-PHASE TESTING CAPABILITY IN A SINGLE CONVENIENT PACKAGE ...

NOT JUST A DIGITAL RELAY TEST SYSTEM

The MTS-1700 is more than a digital relay test system. The high VA current and voltage outputs areideal for performing panel injection and commissioning of entire protection or metering panels. Built-inadvanced manual capabilities allow troubleshooting difficult situations without the use of a computer.

Single-Phase Relay Testing

Differential Relay Testing

Three Phase Relay Testing

V I

I2I1

~~INTERNAL

SWITCHING

MATRIX

3Ø-4 Wire Output Terminals

IA

I3 OUTPUT

Most 3-phase relays can be tested one phaseat a time by switching the current to the phaseunder test (A-N, B-N, C-N, A-B, B-C, C-A). Thisis an ideal method for commissioning protectionand metering panels.

}}

}

V I

B

C N

4

I

V

I1

I2

Vc

VB

VaI

MTS-1720 Two Channel Current Source

Basic Facts

· Combines with the MTS-1710 to build a full 3-phase voltage, 3-phase current system

· Parallelable current channels for higher current & VA· Able to test all three-phase devices· Operation controlled from the MTS-1710

Applications

· Out-of-step/power swing testing· Negative sequence current relay testing· True 3-phase close-in fault simulation· Motor protection relays· Pilotless or loss-of-load accelerated tripping schemes· Fault waveform playback

The MTS-1720 provides 2 current output channels in order toproduce full 3-phase current or to provide higher current/VAoutput when used with the MTS-1710. Control of the outputamplitude, phase, frequency and all other functions are providedthrough the front panel or RS-232C interface. The user operationalconcepts are the same as the MTS-1710, thereby allowing youto become familiar with its use in a matter of minutes.

FOR COMPLETE 3-PHASE TESTING CAPABILITY ....

Very simple rear panel connections forquick and hassle free setup.

IA

IB

IC

IN

Full 3-phase voltage 3-phase current testing Current ParallelingDeviceundertest

Va

VnVcVb

5

Test Relays Under RealisticPower System Conditions

TEST UNDER REALISTIC POWER SYSTEM CONDITIONS

You can now subject devices to realistic powersystem conditions, including DC offsets, transients,and harmonics. The MTS-1700 system can play backrecorded fault waveforms from digital fault recordersand protection relays, as well as IEEE COMTRADE filesand waveform files from computer-generated EMTP(or other) simulations. Since the MTS-1700 systemis field portable, protection systems can be testedon-site, under actual field conditions of temperature,EMI, noise, etc and interacting with other equipment.

Real-world fault records or waveforms fromcomputer simulations can be played back toprotective relays using �Fault Builder� software.

7

�We are doing things with this set that wecould have never done with our previousone.�Gerard ChasseAssistant Electrical Superintendent

Product Highlights

High VA power output

High VA current and voltage channels allow you to test highburden electromechanical relays, as well as digital relays.Built in current modes for high current, paralleling and aunique external current input for extra high burden relaysensures that you get the maximum performance of thesystem to match the task at hand.

Intelligent setup of standard faults

Built-in fault modes allow you to simulateclassical faults (Ø-N, Ø-Ø, 3Ø) with only 3settings (fault voltage, fault current and faultangle). These settings are remembered, andcan be applied to simulate the same fault onother phases with the flip of a switch.

Time-saving features

Direct display of parameters such asimpedance, power and slope allows you toview and adjust directly the parameter ofinterest, enhancing productivity as well asreducing errors.

Front panel accessible dynamic testing

Dynamic as well as steady-state tests can be easily controlled from the front panel.Independent amplitude, phase angle and frequency conditions in prefault, fault andpostfault states can be programmed without the use of a computer.

I

V

8

PREFAULT FAULT POSTFAULT

Every fault simulation function you need

In addition to standard prefault, fault and postfaultsettings, the front panel menu gives you access toadvanced features including fault duration, ramping,point-on-wave control, breaker time simulation,reclose simulation and more.

3-phase angleadjustment

phase-phase V & Iadjustment

3-phase V & Iadjustment

Easy-to-use

Just a few push buttons let you select the function you want, and a single control knobgives the feel of an analog instrument with digital precision. 3-phase voltage/current,phase-to-phase voltage/current, and phase angle of multiple voltages/currents canbe set/adjusted directly. The feature rich alphanumeric display gives at-a-glancereadout of vital settings and parameters.

9

IB

VA

VA

IA

IA

Va

Even greater possibilities are opened up withthe MTS-1700 external synchronizationcapabilities, including end-to-end testing,allowing testing of the protection and associatedcommunications equipment.

End-To-End Testing

}

RELAY 1TRIP

TX

+ -RX

+ -

- DCV}RELAY 2

TRIPTX

+ -RX

+ -

- DCV}

} +DCV

+DCV

VoltageCurrent

VoltageCurrent

Multi-systemsync connection

(rear)

PILOT WIRE RELAY TEST

SOFTWARE FOR END-TO-END TESTING

Note: MTS-1730 shown here for communications channel delay simulation

10

Accessories & Other Products

IISSOO 99000011 RReeggiisstteerreedd4060B Sladeview Crescent, Unit #1 Mississauga, Ontario L5L 5Y5

e-mail: sales@mantatest.com Internet: http://www.mantatest.com

Telephone: (905) 828-6469 Toll Free (USA & Canada): 1-800-233-8031 Fax: (905) 828-6850

Transducer Test / Calibration Multi-function Powermeters

1. Reusable heavy duty shipping case2. Cordura carry case3. Operation and reference manual4. Protective rear and front covers5. Test instrument interconnecting cables

and power cords6. Test lead kit and computer interface

cable (optional)7. Interface cables for specific relays

(optional)

1 2

3

74

5

Current and Voltage Sources

6

CU A007 01A Printed In Canada ©1998 Manta Test Systems Inc.

Represented By: