multi functionalelectronicceramic stew souppot
TRANSCRIPT
1
Multi-FunctionalElectronic Ceramic
Stew /Soup Pot
多功能陶瓷電子燉盅湯鍋
Instruction Manual 說明書
Model 型號: CSP800
Before using your product for first time,please read this instruction manual.
在使用本產品前,請仔細閱讀本說明書並保存好。
2
IMPORTANT SAFEGUARDS
Read the user manual carefully before using the product.Properly keep
this User Manual for future use.
Ignoring the instructions or incorrect operation may result in severe
accidents or other injuries.Make sure you will observe the instructions
below when using the product:
1. The power supply shall be AC220-240V~,50/60 Hz;check and make
sure your power supply is correct.
2. Make sure the socket has secure contact before using the product,
and no extension cable is allowed
3. The product shall be used together with the power cable and socket
delivered together with the product and don’t use other power
cable and socket.
4. Kids are not allowed to operate the product by themselves.Keep the
product out the reach of kids or infants.
5. Don’t use the product on or near to the surface with poor heat
resistance,such as carpet or plastic;don’t put anything which can be
damaged by the steam above the product.
6. Use the product on stable flat surface and keep it out of the reach of
kids or people with disturbance of consciousness to prevent
accidents.
7. Don’t press the keys with too much force, or the keys may be
damaged.
8. Don’t try to touch the steam going out the steam outlet on the
upper cover when the product is working,or you will get scalded.
9. Add water as appropriate according to the scale shown inside the
stew body, or the boiled water may splash out and get people
scalded.Do put on the glass cover when the stew is working.
10. When use the product for the first time,please add water to the max
3
water level and then heat to boil the water to clean the interior.The
boiled water should be discarded.
11. If it is found that the product is working without water,please add
water or unplug power supply. Do not touch the product’s any
heating elements,and housing or you will get scalded.
12. Do not immerse the product in water or other liquids for cleaning,or
accidents may happen.
13. If the power cable is damaged or torn, replace it with dedicated
cable or dedicated modules purchased from the manufacturer or
maintenance department.
14. When the product has faults,do not disassemble it by yourself to
prevent danger.
15. This appliance is for household use only,do not use outdoor.
16. Do not use appliance for other than intended use.
17. This appliance can be used by children aged from 8 years and aboveand persons with reduced physical,sensory or mental capabilities orlack of experience and knowledge if they have been givensupervision or instruction concerning use of the appliance in a safeway and understand the hazards involved.
18. Children shall not play with the appliance. Cleaning and usermaintenance shall not be made by children without supervised.
19. If the supply cord is damaged,it must be replaced by the After-salesService Center or a similarly qualified person in order to avoid ahazard.
4
1.Brief Introduction to the Electric Stew /Soup Pot
Note:The product is upgraded from time to time.The pictures here arefor reference only,actual product may vary.
Glass upper cover
2.2L ceramicpot with lid
0.5L each ceramic potwith lid
Power cable
Stainless steel
steamer rack
Main Body
Control panel
5
Directions for Use of Multi-FunctionalElectronic
Ceramic Stew /SoupPot
1. Soup Making
Put the food into the Electric Stew/Soup Pot
Add appropriate amount ofwater according to the marksshown on the inner surface ofthe stew /Soup pot (waterlevelnot higher than the max.Mark line)
FunctionDefault time
(hour)
Adjustable time
(hour)
Default Temperatur( °C)
Adustable Temperature( °C)
Soup 2 0.1~9.9 /
Stew 3.5 0.1~9.9 /
Dessert 3 0.1~9.9 /
Porride/Rice 2 0.1~9.9 /
Quick
steaming 0.5 0.1~9.9 /
Hotpot / / 90 40-99
Keep
warm 2 0.1~9.9 /
Preset
timer 2 0.1~9.9 / /
6
2. Stew/Soup/Dessert/Porridge/Rice
Add the food to stew in theceramic pot plus appropriateamount of water.
Cover the ceramic lid
Note:Add the water so that itcan cover the food or slightlymore.Total volume of the foodand the water shall not exceed80% of the pot capacity.
Cover the glass cover correctly Plug into power supply
7
Add appropriate amount ofwater into the electricstew/souppot
Put the steamer rack and thefilled pot into the electricstew/soup pot
Note:Add the water reach the“Water level before put in thepot”inside the machine)
Cover the upper cover Connect to the power supply
8
3.Quick Steaming
Put the steamer rack into themain body.
Add appropriate amount of water,too much water may result inreaching the food when boiling.
Put the food on the steamer rack Connect to the power supply
9
4.Hotpot
Add appropriate amount of waterinto the electric stew/souppot,together with hotpot soup whilehotpot cooking.
Cover the glass cover correctly andconnect to the power supply.
Note:The total volume of thefood and the water shall notexceed the water level for“hotpot”shown inside the mainbody.
The hotpot soup is ready when the water is boiled and put the raw foodinto the electric stew /souppot for cooking.
10
Directions for Operation
Icons on the control panel in the standby mode
Plug into the power supply to enter the standby mode and the controlpanel is lit up constantly and shows “OF”.Press “Preset timer”to enterthe preset time mode .Press“Function/Cancel”button to choose thedesired function.Press “+/-”button to set the time (“+/-”doesn’t work inthe standby mode).
1.Presettimer and Function Selecting
甜品
預約
隔水炖 火鍋
保溫
粥/飯
煮汤
快蒸
甜品
預約
隔水炖 火鍋
保溫
粥/飯
煮汤
快蒸
保溫
粥/飯
煮汤
甜品
預約
火鍋
快蒸
保溫
粥/飯
煮汤
甜品
預約
隔水炖 火鍋
快蒸
11
Press “Preset Timer” button in the standby mode and the indicator of
timer flashes and shows the default time of “2.0”hours.Press “+” or
“-” to adjust the duration of timer,or you can long press the “+” or
“-” for quick increase/decrease.Therange can be set from 0.1hour-9.9
hours time. After setting the duration of timer, press the
“ Function/Cancel” button and now the indicator is lit up constantly,
which indicates successful setting of timer.You are now in the stage offunction selecting.The function of “soup”is switched on ,youcan chooseone of the function to finish the setting .The selected indicator lightsremain ON after the preset time and function are set.If there is no need
to set the timer,directly press “Function/Cancel” button to enter the
stage of function selecting.
甜品
預約
隔水炖 火鍋
保溫
粥/飯
煮汤
快蒸
12
In the standby mode or after setting the timer, you can press“Function/Cancel”button to enter the stage of function selecting.Pressthe “Function/Cancel”button to switch the function and the functionindicator flashes.Now,press “+”/“-”button to adjust the operation time.
Important Note:In the function of “Hotpot”,the digits shown on the
digit display is temperature.The temperature range can be set from
40-99℃.
3.Finish the Selection of Function
In the working mode
保溫
粥/飯
煮汤
甜品
預約
火鍋
快蒸
保溫
粥/飯
煮汤
甜品
預約
隔水炖 火鍋
快蒸
甜品
預約
隔水炖 火鍋
保溫
粥/飯
煮汤
快蒸
2.Function Selecting
13
Stop the cooking process when pressing “Function/Cancel”button
The electric stew/soup pot starts working automatically in 10 secondsafter function selection.During operation process, the three buttons of
“Timer”,“+” and“-”don’t work until you press“Function/Cancel”button to stop the timer or steaming/cooking function and then enter intothe standby mode.
Note:If the function “Hotpot” is chosen,the buttons of “+” and “-”
can work normally even when the electric stew /soup pot is in the workingmode.
Attention:Please add water into the electric stew /soup pot according to instructionson water level,or the effects of cooking/stewing may be affected or injurymay be resulted from splashing boiling water;Prolong the working time if use the electric stew /soup pot at lowtemperature (below10oC)to guarantee best effect of stewing/cooking.
Sequence of function selecting is clockwise, that is, soup – stew with
pot – dessert – porridge/rice – quick steaming – hotpot –
keep warm – standby(OF).The temperature controller trips in case of excessive temperature when
the water dries up.Then,the panel shows “EO”and start beeping ,all the
keys don’t work.When the temperature drops or water is replenished,
the temperature controller resets and the control panel shows “EO” and
“OF” (alternatively)for several seconds,which is OK and the product
will later enter the standby mode and the panel shows “OF”.Then the
machine returns to normal working.
甜品
預約
隔水炖 火鍋
保溫
粥/飯
煮汤
快蒸
14
Trouble shooting
Note: Contact our after sales service center for assistance if the faultscannot be resolved with methods shown above.Never dissemble theproduct by unqualified personnel.
Faults Possible Reasons
Display does not light upon the panel
a. Power failureb. Power cable is not connected to the
electric stew/souppot
c. Power cable is not connected to thesocket
d. Power switch is turned off
Food not fully cooked
a. Incorrect setting of cooking time.
b. Inadequate water in the electric stew/souppot or too short time ofstewing/cooking.
Some keys don’twork/have no response
a. Read the User Manual carefully.
15
Cleaning and Maintenance1. Unplug the power cable from the socket immediately after use.
2. Clean the upper cover,the steamer rack,and the ceramic pot withdishwashing liquid and sponge.Don’t clean with hard steel wool,orthe surface of the pots or the upper cover may be damaged.
3. If the electric stew pot is dirty,wipe with a wet towel.Or usecleaning liquid,but do not have water contact with the machinepower position.Don’t immerse the electric stew pot in water forcleaning,or electric leakage or accident may happen.
4. Clean the product and put it in the packing box after drycompletely,keep the carton in a well ventilated and dry place if itwill not be used for long time to avoid humidity and impairedperformance.
5. Water scale can form when heating the food and it always depositson the inner wall and the bottom of the pot which may shorten theservice life of the product and affect the taste of food and thusneed to be removed in time.Generally water scale should beremoved twice a year (subjectto the quality of water);method:mixvinegar and water in the proportion of 1:2and add this mixture intothe electric stew /soup pot until reaching the max water level andheat to boiling.Keep the mixture in the body for 24 hours and thenpour out.Later,add clean water into the electric stew /souppotuntil reach the max level and heat to boiling again,thenpour outthe boiled water.
Product specification:Model No.: CSP800Power:800 -950WFrequency:220-240V~,50/60HzCapacity Main Body:4LProduct Dimension:296(W)x 295(H)x 240(D)mm
16
安全注意事項(1)使用時詳細閱讀本手冊操作說明書,並妥善保管以供日後慘考。
(2)無視該說明書或者操作失誤,都可能會造成重大事故或者其他傷
害的發生,所以,請遵循以下指示:
1.使用電源是 AC220-240V~,50/60 Hz,使用前請檢查電壓標準是否相符。
2.使用本產品時必須確定插座接觸良好,不可使用延長線。
3.產品應和配備的電源線插座使用,不能使用其他電源線插座。
4.請勿讓兒童單獨操作使用,要放在嬰幼兒不能觸及的地方。
5.不要在地毯、塑料等不耐熱的物體表面和附近使用本產品,會因蒸汽
受損的物體不要置於本產品上方。
6.使用時產品應放置於穩固平面上,不可將產品放置在兒童或無意識行
為認識可觸及的地方,以免發生意外。
7.操作按鍵時不可用力過猛,以防按鍵開關損壞。
8.產品工作時,不要觸碰從上蓋的蒸汽口噴出的蒸汽,以防燙傷。
9.加水時,請按照機體內水尺加入適量的水,以防沸水飛濺出來燙傷,
工作時必須蓋上玻璃蓋。
10.第一次使用時,應該加水到最大水位線,然後把水燒滾後倒掉不用,
以便清潔鍋體。
11.若產品啟動乾燒保護裝置,請往產品內加水或拔掉電源,此時切勿
用手觸摸鍋身和發熱體以防燙傷。
12.清潔時嚴禁將機體浸入水中或或其他液體中,以免發生危險。
13. 如電源線損壞時,必須於我司維修部買回專用組件來更換。
14.產品若出現任何故障,為了避免危險,請不要自行拆開機體。
15. 本產品只可作家庭用途,不能放置戶外使用。
16. 不可讓本產品作非指定用途使用。
17. 該電器可適用於 8 歲以上的兒童以及身體,感官或者智力能力下
降和缺乏經驗和知識的人群,他們使用該電器需要得到安全使用電器
的監督或者指導,並且瞭解所涉及的危險。
18. 成人應該指導小孩不可把玩此電器。
19. 定期檢查本產品的電源線。如果電源線損壞,必須由本公司售後服
務部或合格的電器技師更換,以避免危險。
17
主機部分簡介
備註:產品不斷優化升級,圖片僅供參考,具體請以實物為准
2.2L陶瓷燉盅連蓋
0.5L陶瓷燉盅連蓋
可拆式電源線
玻璃上蓋
蒸架
機身
操作面板
18
使用提示
1. 煮湯
在機體內放入食材
並按機身內表面的水尺加入適
量的水(加水量不超過機體內
水尺的最高水位)
功能默認工作時間
(小時)
可調整時間 (小時)
默認溫度 可調溫度
煮湯 2 0.1~9.9 /
隔水燉 3.5 0.1~9.9 /
甜品 3 0.1~9.9 /
粥飯 2 0.1~9.9 /
快蒸 0.5 0.1~9.9 /
火鍋 / / 90 40-99
保溫 2 0.1~9.9 /
預約 2 0.1~9.9 / /
19
蓋好玻璃蓋 接上電源
2.燉/湯/甜品/粥/飯
在燉盅內加入需要燉煮的食材
並加入適量的水蓋上燉盅蓋
注意:加水以剛好浸過食物或略
多一點為宜,加入的食材和水不
超過燉盅內容量的 80%
20
往機體內加入適量的水再將蒸架和裝好食材的燉盅放入
機體
注意:加水至機體內所標“放盅
前水位”水尺位置
蓋上上蓋 接上電源
21
把蒸架放入機體內加入適量的水,水量不適宜過多,
以免水沸騰後觸碰到食物
把食物放到蒸架上 接上電源
3.快蒸
22
往機體內加入適量的水和食材做
火鍋湯底
蓋好玻璃蓋,接上電源
注意:食材和水不能超過機體內
“火鍋”刻度水尺位
待水滾後,火鍋湯底完成。此時可放入食材開始進行火鍋。
4.火鍋
接上電源後本機即進入待機狀態,操作面板常亮顯示“OF”.按“預約”
鍵來進行預約,按“功能/取消”鍵來直接進行功能選擇,按“+,-”
鍵來進行設定時間,待機狀態下按“+,-”鍵不起作用。
1.預約和功能選擇
操作介紹
面板待機狀態
甜品
預約
隔水炖 火鍋
保溫
粥/飯
煮汤
快蒸
甜品
預約
隔水炖 火鍋
保溫
粥/飯
煮汤
快蒸
待機狀態下,按“預約”鍵,預約指示燈閃爍和顯示默認預約時間“2.0”
小時,此時按“+,-”鍵可調節預約時間長短,長按“+,-”鍵時可
快速增減時間,預約的範圍由 0.1小時至最長 9.9小時,設定好預約
時間後按下“功能/取消”鍵,此時預約指示燈常亮顯示,表示預約已
設定完成,同時進入功能選擇狀態。此時可選擇“煮湯”或其他功能
鍵完成預約功能設定。若選定功能及所需時間後待指示燈常亮才完成。
若不需要設定預約,或可直接按“功能/取消”鍵進入功能選擇狀態。
2.設定工作功能
保溫
粥/飯
煮汤
甜品
預約
火鍋
快蒸
保溫
粥/飯
煮汤
甜品
預約
隔水炖 火鍋
快蒸
甜品
預約
隔水炖 火鍋
保溫
粥/飯
煮汤
快蒸
保溫
粥/飯
煮汤
甜品
預約
火鍋
快蒸
保溫
粥/飯
煮汤
甜品
預約
隔水炖 火鍋
快蒸
25
在待機狀態下或設置預約鍵後,按“功能/取消”鍵,則進入功能選擇
狀態,每按一下“功能/取消”鍵,切換對應功能,功能指示燈閃爍,
此時按“+,-”鍵可調節工作時間長短。
重要提示:火鍋功能,數碼顯示尺只會顯示可調節的溫度,不是時間
為單位,設定溫度範圍為 40 至 99 度。
3.完成功能選擇
工作過程中
停止設定需要按“功能/取消”鍵
功能選擇完成後,10 秒後自動進入設定好的工作狀態;在工作過程中,
“預約”鍵 “+,-”鍵不起作用,按“功能/取消”鍵,能夠停止預約
甜品
預約
隔水炖 火鍋
保溫
粥/飯
煮汤
快蒸
甜品
預約
隔水炖 火鍋
保溫
粥/飯
煮汤
快蒸
26
或燉煮工作,進入待機狀態。
注意提示:在火鍋功能工作過程中, “+”及“-”鍵仍可正常操作調
校溫度。
特別提醒:
1.往機體內加水時按照水尺指示加水,以免影響燉煮效果或水沸騰後溢
出傷人。
2.在低溫環境(10 ℃以下)燉煮時,請適當增加燉煮時間,以保證較
佳的燉煮效果
3.功能選項按順時針循環選擇,即:煮湯-隔水燉-甜品-粥/飯-快蒸-火鍋
-保溫-待機。
4.當水燒乾了,溫度過高時,溫控器會自行切斷,顯示屏“EO”顯示,
此時任何按鍵都失效,待溫度降低或機體加入水後,溫控器復位,顯
示屏會持續幾秒“EO”與“OF”交替閃動(此屬於正常現象),過後
產品會進入待機狀態,顯示屏“OF”顯示,並可正常工作。
機器故障
故障描述 可能原因
顯示屏無顯示 a 是否停電
b 電源線插頭與機體插座是否插緊連接
c 電源線是否插入電源插座
d 電源開關是否開啟
食物沒有燉熟 a 設定的時間是否選擇正確
b 機體內加的水太少,燉煮時間太短
某些按鍵失效、沒反應 a 請仔細閱讀本說明書的操作說明
備註:經以上現象分析後仍無法排除故障,請與本公司售後服務部進
行協助,嚴禁非專業人員對本機自行拆卸!
清潔與維護1. 使用完畢後,請及時從電源插座上拔下電源插頭。
2. 玻璃上蓋、蒸架、陶瓷燉盅可用洗潔精和海綿清洗,請勿使用
硬質鋼絲清洗,以免損壞表面。
3. 機體内有污垢時,可用濕毛巾擦拭,或清潔液清洗,但不可有
水接觸機器電源位置。請切勿將機體放入水中清洗,以免漏電及
發生事故。
4. 產品長時間不使用時,請清潔擦凈,裝入包裝箱中,放於通風
和乾燥的地方,以免受潮,影響使用。
5. 水垢是加熱時自然形成的鈣質沈澱物,常粘附在鍋身內壁和底
部,會影響到產品的使用壽命以及食物處理的口感,應及時清除;
正常使用的情況下,壹年约清除 2 次(根據當地水質而定);清除
方法:用醋和水按 1:2的比例混合裝入鍋內到最大水位,然後加熱
至沸騰,將混合液置放 24 小時,然後倒掉,再加入清水至最大水
位,加熱煮沸騰然後倒掉即可。
技術規格
產品型號:CSP800
額定功率:800 -950W
電壓頻率:220-240V~,50/60Hz
機身容量:4 L
產品尺寸:296(闊)x 295(高)x 240(深)mm
F 28
ToolBox
本產品不斷改進中,如功能有所更改,恕不另行通知,如有疑問,請
於客戶服務中心聯繫,不便之處,敬請原諒。
說明書內容以英文版本為準。
ToolBox Customer Service Center 客戶服務中心
7/F.,Goodwill Industrial Building,36-44Pak Tin Par Street,Tsuen Wan,
N.T.
新界荃灣白田壩街 36-44號信義工業大廈 7 樓
Customer Service Hotline 客戶服務熱線:(852)8210 8210
Service Email 電郵地址:[email protected]
Please register now at 請即上網登記:www.toolbox.hk
Website 網址:www.gilman-group.com
Proudly Serviced by
a Gilman Group Company
太平家庭電器
2/F,Shing Dao Industrial Building,232 Aberdeen Main Road,Hongkong
香港香港仔大道 232 號城都工業大廈 2 樓