- my mobile does not get turned oﬀ - 0417 707...

P O Box 9067 Gold Coast Mail Centre QLD 9726 Tel +61 7 5597 6373 Fax: +61 7 5597 6474 Mob: 0417 707 248

E-Mail: [email protected] 99 198 641 856

Pty Ltd



Pty Ltd

COMPONENT SEALS

I am available 24/7- my mobile does not get turned off -

0417 707 248



Pty Ltd

p1

CONTENTS

T502 2

T21 3

MG1 & MG12 4

T2100 5

T32 & T37 6

T21DIN 7

T560 8

T560D 9

T58U & T59U 10

T58B & T59B 11

T7U 12

T7B 13

R3 & R2 14

R3U & R2U 15

BT 16

T80 & T87 17

T6 & T7 18

T7U & T7C 19

METRIC SEAT 20

IMPERIAL SEAT 21

SEAL FOR SPECIFIC PUMP 22

SPECIAL SEAL 23

SPECIAL SEAL 24

SPECIAL SEAL 25

SPECIAL SEAL 26

SEAL FOR FLYGT PUMPS 27

SEAL FOR FLYGT PUMPS 28

CONTENTS 1



Pty Ltd

p2

T502

D1 D3 D7 L1 L4 L1K=L1+L4 14mm 24.0 25.0 23.0 12.0 35.0 16mm 26.0 27.0 23.0 12.0 35.0 18mm 32.0 33.0 24.0 13.5 37.5 20mm 34.0 35.0 24.0 13.5 37.5 22mm 36.0 37.0 24.0 13.5 37.5 24mm 38.0 39.0 26.7 13.3 40.0 25mm 39.0 40.0 27.0 13.0 40.0 28mm 42.0 43.0 30.0 12.5 42.5 30mm 44.0 45.0 30.5 12.0 42.5 32mm 46.0 48.0 30.5 12.0 42.5 33mm 47.0 48.0 30.5 12.0 42.5 35mm 49.0 50.0 30.5 12.0 42.5 38mm 54.0 56.0 32.0 13.0 45.0 40mm 56.0 58.0 32.0 13.0 45.0 43mm 59.0 61.0 32.0 13.0 45.0 45mm 61.0 63.0 32.0 13.0 45.0 48mm 64.0 66.0 32.0 13.0 45.0 50mm 66.0 70.0 34.0 13.5 47.5 53mm 69.0 73.0 34.0 13.5 47.5 55mm 71.0 75.0 34.0 13.5 47.5 58mm 78.0 78.0 39.0 13.5 52.5 60mm 80.0 80.0 39.0 13.5 52.5 63mm 83.0 83.0 39.0 13.5 52.5 65mm 85.0 85.0 39.0 13.5 52.5 68mm 88.0 90.0 39.0 13.5 52.5 70mm 89.0 92.0 45.5 14.5 60.0 75mm 96.0 97.0 45.5 14.5 60.0 80mm 104.0 105.0 45.0 15.0 60.0 85mm 108.0 110.0 45.0 15.0 60.0 90mm 114.0 115.0 50.0 15.0 65.0 95mm 118.0 120.0 50.0 15.0 65.0

100mm 124.0 125.0 50.0 15.0 65.0

Design Features DIN 24960 standard. Full convolution elastomeric bellow seal. Non-clogging single coil spring for de-pendability

Operating Conditions Temperature: -30°C to +200°C(depending on materials used) Pressure: Up to 40 bar , 435 psi Speed: Up to 13m/s, 2500fpm

Materials available Seal face: carbon, ceramic, TC, SIC Elastomer: nitrile, viton, EPR

Equivalent to 502, BO7 seal.

Standard seat BO, BP. Alternative seat cup mounted DIN seat



Pty Ltd



Pty Ltd

p3

T21

D1(IN) D3 D7 L1 L4 L=L1+L4 0.375 21 22.2 22.2 6.3 28.5 0.500 23 25.4 22.2 8.0 30.2 0.625 27 31.8 22.2 10.3 32.5 0.750 31 35.0 22.2 10.3 32.5 0.875 34 38.1 24.0 10.3 34.3 1.000 40 41.3 25.4 11.0 36.4 1.125 45 44.5 27.0 11.0 38.0 1.250 47 47.7 27.0 11.0 38.0 1.375 52 50.8 28.5 11.0 39.5 1.500 54 54.0 28.5 11.0 39.5 1.625 58 60.3 35.0 12.7 47.7 1.750 62 63.5 35.0 12.7 47.7 1.875 66 66.7 38.0 12.7 50.7 2.000 71 69.9 38.0 12.7 50.7 2.125 75 76.2 43.0 14.3 57.3 2.250 79 79.4 43.0 14.3 57.3 2.375 82 82.6 46.0 14.3 60.3 2.500 85 85.7 46.0 14.3 60.3 2.625 92 85.7 49.0 16.0 65.0 2.750 92 88.9 49.0 16.0 65.0 2.875 99 95.3 52.5 16.0 68.5 3.000 99 98.4 52.5 16.0 68.5

Design Features Self- aligning Mechanical drive Non-clogging single coil spring for de-pendability

Operating Conditions Temperature: -30°C to +200°C (Depending on materials used)Pressure: Up to 10 bar , 145 psi Speed: Up to 13m/s, 2500fpm

Materials available Seal face: carbon, ceramic, TC, SIC Elastomer: nitrile, viton.

Equivalent to 21, E43seal

Standard seat CU, OG seat Alternative seat CE, W seat



Pty Ltd

p4

MG1 & MG12

D1 D3 D7 L1 L12 L4 L=L1+L4 L1k=L12+L4

14mm 28.5 25.0 17.0 28.4 6.6 23.6 35.0 15mm 28.5 17.0 28.4 17.0 16mm 28.5 27.0 17.0 28.4 6.6 23.6 35.0 18mm 32.0 33.0 19.5 30.0 7.5 27.0 37.5 20mm 37.0 35.0 21.5 30.0 7.5 29.0 37.5 22mm 37.0 37.0 21.5 30.0 7.5 29.0 37.5 24mm 42.5 39.0 22.5 32.5 7.5 30.0 40.0 25mm 42.5 40.0 23.0 32.5 7.5 30.5 40.0 28mm 49.0 43.0 26.5 35.0 7.5 34.0 42.5 30mm 49.0 45.0 26.5 35.0 7.5 34.0 42.5 32mm 53.5 48.0 27.5 35.0 7.5 35.0 42.5 33mm 53.5 48.0 27.5 35.0 7.5 35.0 42.5 35mm 57.0 50.0 28.5 35.0 7.5 36.0 42.5 38mm 59.0 56.0 30.0 36.0 9.0 39.0 45.0 40mm 62.0 58.0 30.0 36.0 9.0 39.0 45.0 43mm 65.5 61.0 30.0 36.0 9.0 39.0 45.0 45mm 68.0 63.0 30.0 36.0 9.0 39.0 45.0 48mm 70.5 66.0 30.5 36.0 9.0 39.5 45.0 50mm 74.0 70.0 30.5 38.0 9.5 40.0 47.5 53mm 78.5 73.0 33.0 36.5 11.0 44.0 47.5 55mm 81.0 75.0 35.0 36.5 11.0 46.0 47.5 58mm 85.5 78.0 37.0 41.5 11.0 48.0 52.5 60mm 88.5 80.0 38.0 41.5 11.0 49.0 52.5 63mm 65mm 93.5 85.0 40.0 41.5 11.0 51.0 52.5 68mm 96.5 90.0 40.0 41.2 11.3 51.3 52.5 70mm 99.5 92.0 40.0 48.7 11.3 51.3 60.0 75mm 107.0 97.0 40.0 48.7 11.3 51.3 60.0 80mm 112.0 105.0 40.0 48.0 12.0 52.0 60.0 85mm 120.0 110.0 41.0 46.0 14.0 55.0 60.0 90mm 127.0 115.0 45.0 51.0 14.0 59.0 65.0 95mm 132.0 120.0 46.0 51.0 14.0 60.0 65.0

100mm 137.0 125.0 47.0 51.0 14.0 61.0 65.0

Design Features Single spring enclosed bellows seal. Independent on direction of rotation Highly recommended for duties with media containing solids eg. MG1 is the short working length MG12 complies with DIN 24960 L1k working length.

Operating Conditions Temperature: -20°C to +200°C (depending on materials used)Pressure: Up to 12 bar g, 174 psig Speed: Up to 10m/s, 2000 fpm

Materials available Seal face: carbon, SIC Elastomer: nitrile, viton, EPR

Equivalent to BO2, BO12 seal

Standard seat G6, G60.Alternative seat G4, G9



Pty Ltd



Pty Ltd

p5

T2100

D1 D3 D7 L1 L12 L4 L=L1+L4 L1k=L12+L4

14mm 24 25 15 29.0 6 21 35.0 15mm 25 26 15 29.0 6 21 35.0 16mm 26 27 15 29.0 6 21 35.0 18mm 32 33 20 31.5 6 26 37.5 20mm 34 35 20 31.5 6 26 37.5 22mm 36 37 20 31.5 6 26 37.5 24mm 38 39 20 34.0 6 26 40.0 25mm 39 40 20 34.0 6 26 40.0 28mm 42 43 26 36.5 6 32 42.5 30mm 44 45 26 35.5 7 33 42.5 32mm 46 48 26 35.5 7 33 42.5 33mm 47 48 26 35.5 7 33 42.5 35mm 49 50 26 34.5 8 34 42.5 38mm 54 56 30 37.0 8 38 45.0 40mm 56 58 30 37.0 8 38 45.0 43mm 59 61 30 37.0 8 38 45.0 45mm 61 63 30 37.0 8 38 45.0 48mm 64 66 30 35.0 10 40 45.0 50mm 66 70 30 37.5 10 40 47.5 53mm 69 73 30 37.5 10 40 47.5 55mm 71 75 30 37.5 10 40 47.5 58mm 78 78 33 42.5 10 43 52.5 60mm 80 80 33 40.5 12 45 52.5 63mm 83 83 33 40.5 12 45 52.5 65mm 85 85 33 40.5 12 45 52.5 68mm 88 90 33 40.5 12 45 52.5 70mm 90 92 33 48.0 12 45 60.0 75mm 99 97 40 48.0 12 52 60.0 80mm 104 105 40 46.0 14 54 60.0 85mm 109 110 40 46.0 14 54 60.0 90mm 114 115 40 51.0 14 54 65.0 95mm 119 120 40 51.0 14 54 65.0

100mm 124 125 40 51.0 14 54 65.0

Design Features Full compliance with DIN 24960, Single spring enclosed bellows seal. Independent on direction of rota-tionThe drive bands have intermesh-ing tags which create positive drive through the seal T2100 is the short working length T2100 complies with DIN 24960 L1k working length.

Operating Conditions Temperature: -20°C to +200°C (depending on materials used)Pressure: Up to 20 bar , 290 psi Speed: Up to 15m/s, 3000fpm

Materials available Seal face: carbon, SIC Elastomer: nitrile, viton, EPR

Equivalent to 2100, BO5, BO52 seal

Standard seat Cup mounted seat

Alternatives seat



Pty Ltd

p6

T32 & T37

D d3 d7 L32 L37 l418mm 31 30 20.5 18.0 8.0 19mm 33 35 22.0 19.0 7.5 20mm 34 35 22.0 19.0 7.5 22mm 36 35 23.5 20.5 7.5 24mm 38 38 25.0 22.0 7.5 25mm 39 38 26.5 23.5 7.5 28mm 42 42 26.5 24.5 9.0 30mm 44 45 25.0 24.5 10.5 32mm 46 48 28.5 28.0 10.5 33mm 47 35mm 49 52 28.5 28.0 11.0 38mm 54 55 32.2 31.0 10.3 40mm 56 58 34.7 34.0 10.8 43mm 58 62 37.3 35.0 12.0 45mm 61 64 39.2 36.5 11.6 48mm 64 68.4 44.7 42.0 11.6 50mm 66 69.3 45.7 43.0 11.6

Design Features Metric size shafts to comply with DIN 24960 Conical spring dependent on direction of rotation, R/H and L/H spring Unbalanced seals T32 is carbon shrink-fitted in rotary face T37 is sic or tc shrink-fitted in rotary face


Materials available Seal face: carbon/sic, sic/sic Elastomer: nitrile, viton, neoprene, EPD

Equivalent to M32, M37G, BS32 seal

Standard seat G4, G9 Alternative seat G13, G6



Pty Ltd



Pty Ltd

p7

T21DIN

D1 D3 D7 L1 L4 L1K=L1+L4

14mm 16mm 26.5 27 24.7 10.3 35.018mm 30.5 33 27.2 10.3 37.520mm 34.0 35 27.2 10.3 37.522mm 34.0 37 27.2 10.3 37.524mm 40.0 39 29.0 11.0 40.025mm 40.0 40 29.0 11.0 40.028mm 44.5 43 31.5 11.0 42.530mm 46.5 45 31.5 11.0 42.532mm 46.5 48 31.5 11.0 42.533mm 50.5 48 31.5 11.0 42.535mm 51.5 50 31.5 11.0 42.538mm 54.0 56 34.0 11.0 45.040mm 58.0 58 32.3 12.7 45.043mm 61.5 61 32.3 12.7 45.045mm 61.5 63 32.3 12.7 45.048mm 65.5 66 32.3 12.7 45.050mm 70.5 70 34.8 12.7 47.553mm 75.0 73 33.3 14.2 47.555mm 75.0 75 33.3 14.2 47.558mm 79.0 78 38.3 14.2 52.560mm 82.0 80 38.3 14.2 52.563mm 85.0 83 38.3 14.2 52.565mm 85.0 85 36.5 16.0 52.568mm 91.5 90 36.5 16.0 52.570mm 91.5 92 44.0 16.0 60.073mm 99.0 93 44.0 16.0 60.075mm 99.0 97 44.0 16.0 60.0

Design Features Metric size shafts to comply with DIN 24960 L1k Self- aligning Mechanical drive Non-clogging single coil spring for de-pendability



Equivalent to 521, 52, E43DIN seal

Standard seat DIN cup mounted seat Alternative seat BO seat



Pty Ltd

p8

T560

D1 D3 D7 L1 L4 L=L1+L4 10mm 23.5 24 16 7 23 11mm 23.5 24 16 7 23 12mm 26.0 26 17 7 24 14mm 28.0 28 18 7 25 15mm 28.0 28 18 7 25 16mm 30.0 32 19 8 27 18mm 32.5 35 18 8 26 19mm 32.5 35 18 8 26 20mm 34.0 38 20 8 28 22mm 34.0 40 20 8 28 25mm 40.0 44 20 9 29 28mm 44.5 46 21 9 30 30mm 46.5 50 22 9 31 32mm 46.5 54 24 9 33 35mm 51.5 58 26 10 36 38mm 54.0 60 27 10 37 40mm 58.0 64 28 10 38 45mm 61.5 66 30 10 40 50mm 70.5 72 32 10 42

Design Features Metric size shafts to Japanese specifi-cation Self- aligning Mechanical drive Non-clogging single coil spring for de-pendability



Equivalent to 560, EA560 seal

Standard seat cup mounted seat Alternative seat



Pty Ltd



Pty Ltd

p9

T560D

D1 D3 D7 L2 L4 L14mm 30 30 4.0 4.0 36 15mm 30 30 4.0 4.0 36 16mm 18mm 34 38 20mm 38 44 7.5 8.6 50 20mm 38 38 50

24mm 39 44 24mm 38 50 25mm 44 50 8.0 8.6 50 25mm 44 44 50

30mm 44 57 10.7 10.7 60 30mm 50 57 60

35mm 54 57 10.7 10.7 60 35mm 58 64 60

35mm 58 58 60

40mm 68 70 12.0 12.0 65 40mm 64 70 11.5 11.5 65 45mm 68 70 12.0 12.0 65

Design Features Back to back configuration, seal bath in oil chamber, silicon carbide seal face on the impellor side, commonly found in submersible pumps

Operating Conditions Temperature: -30°C to +200°C (Depending on materials used)Pressure: Up to 5 bar , 75psi Speed: Up to 5m/s,1000fpm

Materials available Seal face: carbon, ceramic, SIC Elastomer: nitrile, viton.

Equivalent to ED560seal



Pty Ltd

p10

T58U & T59U

D1 D3 D7 L1 L4 L1K=L1+L4

22mm 36 37 24.0 13.5 37.5 24mm 38 39 26.7 13.3 40.0 25mm 39 40 27.0 13.0 40.0 28mm 42 43 30.0 12.5 42.5 30mm 44 45 30.5 12.0 42.5 32mm 46 48 30.5 12.0 42.5 33mm 47 48 30.5 12.0 42.5 35mm 49 50 30.5 12.0 42.5 38mm 54 56 32.0 13.0 45.0 40mm 56 58 32.0 13.0 45.0 43mm 59 61 32.0 13.0 45.0 45mm 61 63 32.0 13.0 45.0 48mm 64 66 32.0 13.0 45.0 50mm 66 70 34.0 13.5 47.5 53mm 69 73 34.0 13.5 47.5 55mm 71 75 34.0 13.5 47.5 58mm 78 78 39.0 13.5 52.5 60mm 80 80 39.0 13.5 52.5 63mm 83 83 39.0 13.5 52.5 65mm 85 85 39.0 13.5 52.5 68mm 88 90 39.0 13.5 52.5 70mm 90 92 45.5 14.5 60.0 75mm 95 97 45.5 14.5 60.0 80mm 104 105 45.0 15.0 60.0 85mm 109 110 45.0 15.0 60.0 90mm 114 115 50.0 15.0 65.0 95mm 119 120 50.0 15.0 65.0

100mm 124 125 50.0 15.0 65.0

Design Features Metric size shafts to comply with DIN 24960 L1k Multiple spring arrangement

T58U is o-ring type seals T59U is wedge type seals


Materials available Seal face: carbon/ceramic, sic/sic Elastomer: nitrile, viton, neoprene, EPD, PTFE

Equivalent to 58U, 59U, M03S, M03

Standard seat BO, BP Alternative seat



Pty Ltd



Pty Ltd

p11

T58B & T59B

D2/D1 D3 D7 L1 L4 L1K=L1+L4

18/22mm 36 33 31.5 13.5 45.0 20/24mm 38 35 31.5 13.5 45.0 22/26mm 40 37 31.5 13.5 45.0 24/28mm 42 39 34.2 13.3 47.5 25/30mm 44 40 34.5 13.0 47.5 28/33mm 47 43 37.5 12.5 50.0 30/35mm 49 45 38.0 12.0 50.0 32/38mm 54 48 38.0 12.0 50.0 33/38mm 54 48 38.0 12.0 50.0 35/40mm 56 50 38.0 12.0 50.0 38/43mm 59 56 39.5 13.0 52.5 40/45mm 61 58 39.5 13.0 52.5 43/48mm 64 61 39.5 13.0 52.5 45/50mm 66 63 39.5 13.0 52.5 48/53mm 69 66 39.5 13.0 52.5 50/55mm 71 70 44.0 13.5 57.5 53/58mm 78 73 44.0 13.5 57.5 55/60mm 80 75 44.0 13.5 57.5 58/63mm 83 78 49.0 13.5 62.5 60/65mm 85 80 49.0 13.5 62.5 63/68mm 88 83 49.0 13.5 62.5 65/70mm 90 85 49.0 13.5 62.5 70/75mm 95 90 55.5 14.5 70.0 75/80mm 104 92 55.5 14.5 70.0 80/85mm 109 97 55.0 15.0 70.0 85/90mm 114 105 60.0 15.0 75.0 90/95mm 119 110 60.0 15.0 75.0 95/100m

m124 115 60.0 15.0 75.0

Design Features Metric size shafts to comply with DIN 24960 L1k Hydraulically balanced seal Multiple spring arrangement T58B is o-ring type seals T59B is wedge type seals


Materials available Seal face: carbon/ceramic, sic/sic Elastomer: nitrile, viton, neoprene, EPD, PTFE

Equivalent to 58B, 59B, M04S, M04seal

Standard seat BO, BP Alternative seat



Pty Ltd

p12

T7U

D1 D3 D7 L1 L4 L1K=L1+L4

22mm 37 37 26.0 11.5 37.5 24mm 39 39 28.5 11.5 40.0 25mm 40 40 28.5 11.5 40.0 28mm 43 43 31.0 11.5 42.5 30mm 45 45 31.0 11.5 42.5 32mm 47 48 31.0 11.5 42.5 33mm 48 48 31.0 11.5 42.5 35mm 50 50 31.0 11.5 42.5 38mm 55 56 31.0 14.0 45.0 40mm 57 58 31.0 14.0 45.0 43mm 60 61 31.0 14.0 45.0 45mm 62 63 31.0 14.0 45.0 48mm 65 66 31.0 14.0 45.0 50mm 67 70 32.5 15.0 47.5 53mm 70 73 32.5 15.0 47.5 55mm 72 75 32.5 15.0 47.5 58mm 79 78 37.5 15.0 52.5 60mm 81 80 37.5 15.0 52.5 63mm 84 83 37.5 15.0 52.5 65mm 86 85 37.5 15.0 52.5 68mm 89 90 34.5 18.0 52.5 70mm 91 92 42.0 18.0 60.0 75mm 99 97 42.0 18.0 60.0 80mm 104 105 41.8 18.2 60.0 85mm 109 110 41.8 18.2 60.0 90mm 114 115 46.8 18.2 65.0 95mm 119 120 47.8 17.2 65.0

100mm 124 125 47.8 17.2 65.0

Design Features Metric size shafts to comply with DIN 24960 L1k Wave spring arrangement Unbalanced seals Independent on direction of rotation


Materials available Seal face: carbon/sic, sic/sic Elastomer: nitrile, viton, neoprene, EPD, PTFE

Equivalent to M7N

Standard seat G9 Alternative seat G4, G13, G6



Pty Ltd



Pty Ltd

p13

T7B

D2/D1 D3 D7 L1 L4 L1K=L1+L4

18/22mm 37 33 33.5 11.5 45.0 20/24mm 39 35 33.5 11.5 45.0 22/26mm 40 37 33.5 11.5 45.0 24/28mm 43 39 36.0 11.5 47.5 25/30mm 45 40 36.0 11.5 47.5 28/33mm 47 43 38.5 11.5 50.0 30/35mm 48 45 38.5 11.5 50.0 32/38mm 50 48 38.5 11.5 50.0 33/38mm 55 48 38.5 11.5 50.0 35/40mm 57 50 38.5 11.5 50.0 38/43mm 60 56 38.5 14.0 52.5 40/45mm 62 58 38.5 14.0 52.5 43/48mm 65 61 38.5 14.0 52.5 45/50mm 67 63 38.5 14.0 52.5 48/53mm 70 66 38.5 14.0 52.5 50/55mm 72 70 42.5 15.0 57.5 53/58mm 79 73 42.5 15.0 57.5 55/60mm 81 75 42.5 15.0 57.5 58/63mm 84 78 47.5 15.0 62.5 60/65mm 86 80 47.5 15.0 62.5 63/68mm 89 83 47.5 15.0 62.5 65/70mm 91 85 47.5 15.0 62.5 70/75mm 99 90 52.0 18.0 70.0 75/80mm 104 92 52.0 18.0 70.0 80/85mm 109 97 51.8 18.2 70.0 85/90mm 114 105 56.8 18.2 75.0 90/95mm 119 110 56.8 18.2 75.0 95/100m

m124 115 57.8 17.2 75.0

Design Features Metric size shafts to comply with DIN 24960 L1k Wave spring arrangement Hydraulically balanced seals Independent on direction of rotation


Materials available Seal face: carbon/sic, sic/sic Elastomer: nitrile, viton, neoprene, EPD, PTFE

Equivalent to H7N

Standard seat G9 Alternative seat G4, G13, G6



Pty Ltd

p14

R3

D1 D3 D7 L1 L4 L=L1+L4 10mm 20 18.1 15 5.5 20.5 12mm 22 20.6 18 5.5 23.5 14mm 25 23.1 22 6.0 28.0 15mm 29 26.9 22 7.0 29.0 16mm 29 26.9 23 7.0 30.0 17mm 29 26.9 23 7.0 30.0 18mm 33 30.9 24 8.0 32.0 19mm 33 30.9 25 8.0 33.0 20mm 33 30.9 25 8.0 33.0 21mm 38 35.4 25 8.0 33.0 22mm 38 35.4 25 8.0 33.0 23mm 38 35.4 27 8.0 35.0 24mm 38 35.4 27 8.0 35.0 25mm 40 38.2 27 8.5 35.5 28mm 46 43.3 29 9.0 38.0 29mm 46 43.3 30 9.0 39.0 30mm 46 43.3 30 9.0 39.0 32mm 46 43.3 30 9.0 39.0 33mm 48 53.5 39 11.5 50.5 35mm 50 53.5 39 11.5 50.5 38mm 56 60.5 39 11.5 50.5 40mm 58 60.5 39 11.5 50.5

Design Features Metric size shafts, seat comply with FE housing Conical spring dependent on direction of rotation Unbalanced seals R3 is ceramic rotary and carbon seat as standed R2 is stainless rotary and carbon seat as standed


Materials available Seal face: ceramic, carbon, sic Elastomer: nitrile, viton, EPD

Equivalent to SIMPLEX, ROTEN3, ROTEN2

R2



Pty Ltd



Pty Ltd

p15

D1 D3 D7 L1 L4 L=L1+L4 10mm 20 21 15 7 22 12mm 22 23 18 7 25 14mm 25 25 22 7 29 16mm 29 27 23 7 30 18mm 33 33 24 10 34 20mm 33 35 25 10 35 22mm 38 37 25 10 35 24mm 38 39 27 10 37 25mm 40 40 27 10 37 28mm 46 43 29 10 39 30mm 46 45 30 10 40 32mm 46 48 30 10 40 33mm 48 48 39 10 49 35mm 50 50 39 10 49 38mm 58 56 42 13 55 40mm 58 58 42 13 55

Design Features Metric size shafts, seat comply with DIN hous-ing Conical spring dependent on direction of rota-tion Unbalanced seals R3U is ceramic rotary and carbon seat as standed R2U is stainless rotary and carbon seat as standed


Materials available Seal face: ceramic, carbon, sic Elastomer: nitrile, viton, EPD

Equivalent to SIMPLEX, UNITEN3, UNITEN2

R3U

R2U



Pty Ltd

p16

BT

Design Features Enclosed rubber bellows seal. European designed. Main feature is the short work-ing length

Operating Conditions Temperature: -30°C to +200°C(depending on materials used)Pressure: Up to 6 bar, 87psi Speed: Up to 12m/sec, 2400fpm

Materials available carbon/ceram ic/nitrile sic/sic/viton

Equivalent to FA, BO1, T55, CYCLAM seal.

D1 D3 D7 L1 L2 L=L1+L2 6mm 18 22.0 11.0 4.0 15.0 8mm 18 22.0 11.0 4.0 15.0 8mm 18 26.0 11.0 8.0 19.0

10mm 24 26.0 11.0 8.0 19.0 11mm 24 26.0 13.0 8.0 21.0 12mm 24 26.0 13.0 8.0 21.0 12mm 24 25.0 13.0 5.5 18.5 12mm 24 26.0 13.0 5.5 18.5 13mm 24 26.0 13.0 5.5 18.5 13mm 24 26.0 13.0 8.0 21.0 14mm 28 28.5 13.0 8.0 21.0 14mm 28 29.5 13.0 8.0 21.0 14mm 28 25.0 13.0 6.0 19.0 15mm 28 29.5 13.0 8.0 21.0 15mm 32 38.0 13.0 8.0 21.0 16mm 28 29.5 13.0 8.0 21.0 16mm 32 38.0 13.0 8.0 21.0 17mm 39 42.0 13.0 8.0 21.0 18mm 32 32.0 13.0 6.5 19.5 18mm 39 42.0 13.0 8.0 21.0 19mm 39 42.0 13.0 8.0 21.0 20mm 35 35.0 15.5 8.3 23.8 20mm 39 42.0 13.0 8.0 21.0 20mm 42 45.0 13.0 10.0 23.0 22mm 39 42.0 13.0 8.0 21.0 22mm 42 45.0 13.0 10.0 23.0 24mm 47 50.0 13.5 10.0 23.5 25mm 47 50.0 13.5 10.0 23.5 25mm 42 39.3 13.5 8.4 21.9 25mm 42 39.3 13.5 6.0 19.5 28mm 54 57.0 15.0 10.0 25.0 30mm 54 57.0 15.0 10.0 25.0 32mm 54 57.0 15.0 10.0 25.0 35mm 60 63.0 16.0 10.0 26.0 38mm 65 68.0 18.0 12.0 30.0 40mm 65 68.0 18.0 12.0 30.0 45mm 70 73.0 20.0 12.0 32.0 50mm 85 88.0 23.0 15.0 38.0 55mm 85 88.0 23 15 38



Pty Ltd



Pty Ltd

p17

T80 & T87

D1 D3 D7 L1 L4 L=L1+L4 0.625 27.0 28.5 19.1 6.3 25.416mm 27.0 28.5 19.1 6.3 25.40.750 30.0 31.7 19.1 6.3 25.424mm 34.1 35.4 19.1 7.6 26.728mm 40.0 42.0 19.1 7.6 26.71.125 39.5 41.2 19.1 7.6 26.730mm 41.0 42.7 19.1 7.6 26.71.250 42.4 44.2 19.1 7.6 26.732mm 42.4 44.4 19.1 7.6 26.71.375 45.5 47.6 19.1 7.6 26.71.500 51.8 53.9 21.1 8.1 29.21.750 58.2 60.3 21.1 8.1 29.21.875 61.4 63.5 21.1 8.1 29.250mm 61.9 63.9 21.1 8.1 29.22.000 64.6 66.6 22.1 9.6 31.72.125 71.0 73.0 22.1 9.6 31.72.125 71.0 73.9 22.1 9.6 31.72.150 72.0 75.0 22.1 9.6 31.755mm 72.0 75.0 22.1 9.6 31.763mm 79.3 83.0 25.8 9.1 34.92.500 79.3 88.9 25.8 9.1 34.92.750 88.9 95.2 25.8 9.1 34.92.875 94.0 98.4 25.8 9.1 34.975mm 96.0 100.4 25.8 9.1 34.9

PUMP D1 D3 D7 L1 L4 SR1 20mm 31.0 30 19.1 10.7 SR2 30mm 41.0 41 19.1 10.9 SR3 35mm 45.5 47 21.1 12.2 SR4 45mm 58.2 58 21.1 11.6 SR5 55mm 72.0 70 22.1 13.0 SR6 75mm 96.0 92 25.8 14.5

Design Features O-ring pusher seals designed Wave spring arrangement Short working length mechanical seal The seal can installed either internal or external Most commonly used on lobe, gear pumps

Operating Conditions Temperature: -30°C to +200°C (Depending on materials used)Pressure: Up to 10 bar , 145 psi Speed: Up to 5.5m/s, 1100fpm

Materials available Seal face: stainless/carbon, TC/TC Elastomer: nitrile, viton, EPD

Equivalent to T80,T87



Pty Ltd

p18

D1(IN) D3 D7 L1 L4 L=L1+L4 0.375 24 22.2 16.7 6.3 23 0.500 27 25.4 16.7 8 24.7 0.625 31 31.75 18.3 10.3 28.6 0.750 35 34.95 18.3 10.3 28.6 1.000 43.5 41.3 20.7 11 31.7

D1 D3 D7 L1 L2 L40.375 24.0 23.0 10.0 8 0.500 28.5 25.4 10.2 8 6.3 0.500 30.0 25.0 10.2 8 5.0 0.500 33.4 25.4 10.2 8 6.3 0.625 36.5 31.0 10 10.3

0.625 38.1 11.0 10 0.750 40.0 35.0 11.0 10 10.31.000 47.0 41.3 19.0 12 1.125 52.0 48.0 16.0 12

Design Features stationary seal design Pressure: Up to 4 bar , 60 psi Speed: up to 45m/s, 9000fpm

Materials available Seal face: carbon, ceramic, sic Elastomer: nitrile, viton

Equivalent to T6A, T68, T7, T790, BO3



Equivalent to T6, T16, BO4

T6

T7



Pty Ltd



Pty Ltd

p19

D1 D3 D7 L12 28.50 25.0 17.50 12 30.00 26.0 17.50 16 36.50 28.5 19.00 20 40.00 36.8 22.50

D1 D3 D7 L1 L410 27 23 14.0 412 32 25 14.2 516 41 31 16.8 520 45 35 17.5 525 52 44 20.0 11 30 58 48 21.0 8

Design Features Unitised design

Operating Conditions Temperature: -30°C to +100°C Pressure: Up to 4 bar , 60 psi Speed: up to 45m/s, 9000fpm

Materials available carbon/cerami/nir Equivalent to T6A, T68

Design Features stationary seal design to run at higher operating speed Operating Conditions Temperature: -30°C to +180°C (Depending on materials used)Pressure: Up to 4 bar , 60 psi Speed: up to 45m/s, 9000fpm


Equivalent to T6A, T68, T7, T790, BO3

T7U

T7C



Pty Ltd

p20

METRIC SEAT

D1 D2 L1 L2 L3=L4 L5 D710mm 19.2 6.6 6.6 10.0 21

12mm 21.6 5.6 6.6 10.0 23

14mm 24.6 5.6 6.6 12.0 10.0 25 15mm 24.6 6.6 16mm 28.0 7.5 6.6 12.0 10.0 27 18mm 30.0 8.0 7.5 13.5 11.5 33 20mm 35.0 7.5 7.5 13.5 11.5 35 22mm 35.0 7.5 7.5 13.5 11.5 37 24mm 38.0 7.5 7.5 13.3 11.5 39 25mm 38.0 7.5 7.5 13.0 11.5 40 28mm 42.0 9.0 7.5 12.5 11.5 43 30mm 45.0 10.5 7.5 12.0 11.5 45 32mm 48.0 10.5 7.5 12.0 11.5 48 33mm 50.0 11.0 7.5 12.0 11.5 48 35mm 52.0 11.0 7.5 12.0 11.5 50 38mm 55.0 10.3 9.0 13.0 14.0 56 40mm 58.0 10.8 9.0 13.0 14.0 58 43mm 62.0 12.0 9.0 13.0 14.0 61 45mm 64.0 11.6 9.0 13.0 14.0 63 48mm 68.4 11.6 9.0 13.0 14.0 66 50mm 69.3 11.6 9.5 13.5 15.0 70 53mm 72.3 12.3 11.0 13.5 15.0 73 55mm 75.4 13.3 11.0 13.5 15.0 75 58mm 78.4 13.3 11.0 13.5 15.0 78 60mm 80.4 13.3 11.0 13.5 15.0 80 65mm 85.4 13.0 11.0 13.5 15.0 85 68mm 91.5 13.7 11.3 13.5 18.0 90 70mm 92.0 13.0 11.3 14.5 18.0 92 75mm 99.0 14.0 11.3 14.5 18.0 97 80mm 104.0 15.0 12.0 15.0 18.2 105 85mm 109.0 14.8 14.0 15.0 18.2 110 90mm 114.0 14.8 14.0 15.0 18.2 115 95mm 120.3 15.8 14.0 15.0 17.2 120

100mm 123.3 15.8 14.0 15.0 17.2 125

H4 seat equivalent to G4 seat



HB seat equivalent to BO seat

HP seat equivale nt to BP seat

Materials available Seat: ceramic, SICTV Elastomer: nitrile, viton, EPD



Pty Ltd



Pty Ltd

p21

IMPERIAL SEAT

D1(IN) D1 L1 L2 D70.375 22.30 8.0 8.7 24.60 0.500 25.40 8.0 8.7 27.80 0.625 31.75 10.3 10.3 30.95 0.750 34.95 10.3 10.3 34.15 0.875 38.10 10.3 10.3 37.30 1.000 41.30 11.0 10.3 40.50 1.125 44.45 11.0 11.9 47.65 1.250 47.65 11.0 11.9 50.80 1.375 50.80 11.0 11.9 54.00 1.500 54.00 11.0 11.9 57.15 1.625 60.30 12.7 11.9 60.35 1.750 63.50 12.7 11.9 63.50 1.875 66.65 12.7 11.9 66.70 2.000 69.85 12.7 13.5 69.85 2.125 76.20 14.3 13.5 73.05 2.250 79.40 14.3 13.5 76.20 2.375 82.55 14.3 13.5 79.40 2.500 85.87 14.3 13.5 82.55 2.625 85.70 16.0 15.9 92.10 2.750 88.90 16.0 15.9 95.25 2.875 95.25 16.0 15.9 98.45 3.000 98.40 16.0 15.9 101.60 3.125 101.60 19.8 19.8 111.15 3.250 104.80 19.8 19.8 114.30 3.375 107.95 19.8 19.8 117.50 3.500 111.15 19.8 19.8 120.65 3.625 114.30 19.8 19.8 123.85 3.750 117.50 19.8 19.8 127.00 3.875 120.65 19.8 19.8 130.20 4.000 123.85 19.8 19.8 133.35

CE seat equivalent to N seat

Materials available Seat: ceramic, SIC, TC Elastomer: nitrile, viton,



Pty Ltd

p22

AHLSTROM IBEX MOG

AJAX INDENG

ALBIN INOXPA

ALFA LAVAL JABSCO PUMP

ALLFLEX JOHNSON PUMP

APV PUMP KSB

DAB PUMP LOWARA

DAVEY PUMP MAGNETIC PUMP

EBARA MONO PUMP

FINSBURY ONGA

FLOMAX PASILAC

FLYGT REGENT PUMP

FORRERS SIHI

FRISTAM SOUTHERN CROSS

GAAM TKL

GORMAN RUPP TSURUMI

GRUNDFOS VARISCO

SEAL FOR SPECIFIC PUMP



Pty Ltd



Pty Ltd

p23

E RANG SEAL

SIZE 24MM 32MM 44MM

DIPLO SEAL

H16-0.75O”CARBON/CERAMIC/VITON NO METAL PARTS FOR CHEMICAL

MONO MACERATORT40-1.000”

T6 UK-1.000”

H70 SEAL

SIZE 15MM 16MM



Pty Ltd

p24

APV W SERIES SEAL APV W+ SEAL SIZE 25MM 35MM

APV LOBE PUMP SEAL 1.125” & 55MM A2356/404-041885002

JOHSON-ONLINEC14-4513-02, TC/TC/V C24-4513-02, TC/TC/V C34-4513-02, TC/TC/V

WAUKESHASIZE 1.125” 1.500”

PASILACSIZE 20, 25, 30, 48, 54 MM

H740 EXTERNAL SEAL SIZE. 1.000”- 2.125” SIZE, 25MM –53MM CARBON/CERAMIC/V SIC/SIC/V

H20-1.250 PTFE/CERAMIC

BOOT SEAL 15052-928408-0000



Pty Ltd



Pty Ltd

p25

SIHI VACUUM PUMP SEAL

SIZE 24, 38, 43, 60, 70MM RIGHT AND LEFT HAND SPRING

GRUNDFOS PUMP SEAL

SIZE 12MM, 16MM, 22MM

SUB PUMP SEAL FOR GRUNDFOSABS, DAB, ZENIT PUMP

SUB PUMP SEAL FOR TSURUMI PUMP SAKURAGAWA PUMP EBARA PUMP

AUTO COMPRESSOR SEAL



Pty Ltd

p26

CYCLONE SEPARATOR (PLANS31 AND41)

WE SUPPLY UP TO 380MMSILICON CARBIDE (REACTION BONDED)

TUNGSTEN CARBIDE (NICKEL BONDED)

TUNGSTEN CARBIDE (COBALT BONDED)

CERAMIC (99.5% ALUMINUM OXIDE)

FOR ALL SEAL FACE, INSERT, SLEEVE, SHAFT

CARBON PRODUCT

CARBON PTFE AND PTFE PRODUCT

MULTISPRING SETTING CLIP

FORRERS PUMP SEAL

SIZE, 1.125”, 1.625”, 2.250”, 2.875 SIZE, 25, 28, 45, 63 , 75, 90 MM



Pty Ltd



Pty Ltd

p27

20MM

3085 3067 3066

22MM

2102-041 2102-040

25MM

3102-180

28MM

2125-180 2125-181 3101-180 2140

35MM

2151-011



Pty Ltd

p28

35MM

3127-180 3126-181

33/35MM

2151-010 3126-180

GRINDEX SEAL

35/45 2201-010 43/45 3152-120 55/60 3170-180, 3201-120 60/60 2250-011 75/90 3300-180

- my mobile does not get turned oﬀ - 0417 707...

Documents