nanoskin car care products 2011

Paint Protection

Glass Protection

Wheel Protection

Leather, Vinyl, Rubber, Tire & Plastic Protection

Fabric & Carpet Protection

Cleaners, Degreasers, Shampoo, Scents, Maintenance

Polishes

Solvents

GLASS MOLECULENano Protective Shield

• Hardens to form a protective shield

• Prolongs surface perfection

• Relentless water beading

• Unique UV absorber

• Silicone Free

• Easy on, easy off

• Single stage and clear coat safe

NANOSKIN GLASS MOLECULE is a chemical solution that uses sol-gel process

to form a colloid of solid particles under 100 nanometers in size, which hardens to

form a protective shield (glass-like film), prolonging surface perfection, NOT a wax

or Teflon. Durability is strong with a consistent 25~30 car washes.

Best results are achieved by applying with 0.8mm mini HVLP spray gun@20PSI in

very thin coats. GLASS MOLECULE has a 24-48 hour cure time which requires no

attention from the user. After the cure, GLASS MOLECULE will be glossier and

harder.

Directions:

1. Rinse car with water to remove dirt and grease, then dry.

2. Clay the surface to remove contamination.

3. Remove any oil & grease with IPA glass cleaner.

4. Point spray nozzle towards surface area and spray evenly.

(0.8mm HVLP mini spray gun)

5. 2 times application is needed.

6. Allow to haze for 30 minutes, then wipe off with clean dry microfiber towels.

13.5oz

Description:

• Uses sol-gel to synthesize gels with particle

size less than 100nm, as shown in Figure A &

Figure B.

• By combining with polymer materials or

petroleum solvent formulas, the mixture can be

directly coated on a material surface by

spraying, dipping or painting.

• A glass-like protective film is created.

• Imparts excellent protective characteristics to

most types of surfaced including clear coated,

painted, aluminum, polished and anodized.

• Film Hardness 3H-4H.

(Meets ASTM D3363 criteria.)

• GLASS MOLECULE offers excellent water

repellency on the treated surface. Contact

angle measurements of the blends and

composites were conducted in a FTA-100

series.

PerformanceWater Repellency

• Introduction

Once the protective shield was coated on the painted

sheet, the degree of the contact angle increment was

tested. The purpose of this test was to verify the water

repellency after the coating of the protective shield on the

experimental painted sheet.

• Preparations and treatment of samples

Sample 1: Untreated painted sheet (uncoated)

Sample 2: Painted sheet coated with the protective

sheet

• Analysis method

A contact angle meter (FTA-100) was used to measure the

contact angle of water droplets. A distilled water droplet

was dropped onto a sample, and the contact angle was

measured. The droplet amount was 2μL, and five contact

angles were measured respectively for each sample to find

the average value.

• Analysis Result

Contact angle of water droplet

Sample 1 - Untreated

painted sheet (uncoated)

82.4±2.3

Sample 2 - Painted sheet

coated with protective

shield

109.3±2.0

Hardness Test1. Pre-test preparations

Pencil hardness testing mechanism preparation

(1) Pencils of 17 levels of hardness are sharpened and

laid out as pictured. The range of hardness from soft

to hard are

6B 5B 4B 3B 2B B HB F H 2H 3H 4H 5H 6H 7H 8H 9H

(2) A pencil hardness measurer meeting the ASTM D 3363

criteria is setup.

2. Preparation and processing of sample slides:

(1) Painted steel plates are buffed and cleaned.

(2) The protective film is evenly sprayed onto the

cleansed surface of the steel plates.

(3) Once dry, the surface is waxed and polished.

•

3. Test operations:

(1) The hardness test is conducted from the softest to

hardest.

(2) The pencil is placed in the measured as pictured

(3) The measurer is pushed across the surface of the

painted metal sheet at a speed of 5-10cm per second.

If there is a mere pencil mark that can be erased, the

pencil is not hard enough to scratch the surface.

(4) As hardness increases, a thread of paint is scraped

off from the surface, as pictured.

4. Results: Threshold of 3H

High/Low Temperature Test1. Foreword:

Metal sheets coated with GLASS MOLECULE are placed

in high temperature (150℃) and low temperature (0℃)

environments to test contact angles as an experience to

see whether the product retains its water repellency under

extreme temperatures.

2. Processing and preparation of samples:

Sample1: Painted surface coated with GLASS MOLECULE


after being placed under high heat (150℃)


after being placed under cold temp (0℃)

3. Method of analysis:

2μL of water is dropped on each sample. The contact

angle at which the droplet touches the surface of the

sample is measured using the FTA-100. This procedure is

done at five different points on each sample and the

average is taken.

Salt Water Test

1. Foreword:

A painted surface coated with GLASS MOLECULE is

soaked in 0.1M salt water for 48 hours, after which the

contact angle is measured to see whether GLASS

MOLECULE retains its water repellency after going

through extreme environments.


Sample1: Painted surface coated with GLASS

MOLECULE

Sample2: Painted surface coated with GLASS

MOLECULE, soaked in 0.1M salt water for 48

hours.


2μL of water is dropped on each sample. The contact angle

at which the droplet touches the surface of the sample is

measured using the FTA-100. This procedure is done at

five different points on each sample and the average is

taken.

Contact Angle

Sample 1: Painted surface coated with GLASS

MOLECULE

109.4±2.3


MOLECULE after being placed under high heat

(150℃)

108.1±0.7


MOLECULE after being placed under cold temp (0℃)

107.2±0.8

Contact Angle


MOLECULE

109.4±2.3


MOLECULE, soaked in 0.1M salt water for 48

hours

105.9±0.6

Wash Durability Test1. Foreword:

The purpose of this report is to state the effects of washing

on a car body coated with GLASS MOLECULE; whether it

effects the water repellency. The test is done by washing

the same surface with soap water and sponge 1,000

times, then measuring the contact angle.


A metal sheet 5cm x 5cm in size is coated with GLASS

MOLECULE. After it air-dries, the pre-washed contact

angle is measured.


2μL of water is dropped on the sample. The contact angle




taken.

4. The wash test is done according to the experiment setup

regulated by ASTM D2486. The sample secured on the

machine counter where the sponge, moistened with

neutral soap, conducts the washing process. Each wipe to

and forth counts as one time, and the surface is washed

1,000 times. Upon completion, the sample is removed

from the machine, rinsed with water, air-dried, and the

contact angle is measured again.

4. Results

Implication:

The outstanding water repellency quality of GLASS

MOLECULE remains even after as many as 1,000 washes.

Test against Acidity/Alkalinity1. Foreword:

The purpose of this report is to test and state the effects of

acid or alkaline on GLASS MOLECULE. Samples are

soaked for one day in strong acid, weak acid, strong

alkaline, weak alkaline, or tap water for one full day. The

contact angle of each is measured to examine water

repellency.

2. Processing and preparation of samples

Metal sheets 5cm x 5cm in size are coated with GLASS

MOLECULE. After they air-dry, the pre-soak contact angle

is measured.

Contact Angle

Painted surface coated with GLASS

MOLECULE – Pre-wash

107.4±0.5

Painted surface coated with GLASS

MOLECULE – After 1,000 washes

105.3±0.5


2μL of water is dropped on each sample. The contact angle




taken.

The following five solutions are prepared:

A. Strong acid solution – 1N concentrated

hydrochloric acid (pH<1)

B. Weak acid solution – 0.1N acetic acid (pH = 4.0)

C. Weak alkaline solution – 0.1N bicarbonate (pH = 9.0)

D. Strong alkaline solution – 1N sodium hydroxide (pH>13)

E. Neutral solution – tap water

A metal sheet coated with GLASS MOLECULE is soaked

in each of the solutions for 24 hours, removed, rinsed, and

air-dried. The contact angle of each is then measured.

4. Test Results

Solution Pre-soak Contact

Angle

Post-soak Contact

Angle

Neutral solution

110.0±0.5

110.5±0.9

Strong acid solution Paint peeled off

Weak acid solution 110.1±0.8

Weak alkaline solution 107.8±1.3

HYDRO EXPRESSHydrophobic Spray Polymer

• The most advanced spray polymer

• The missing link between washing and waxing

• A spray polymer that actually repels water

• Contains durable anti-static polymer

• Lasts up to 2 months

• Restores perfect finish

• Enhances reflections on shiny materials

• May also be used on glass, chrome and plastic

If you’re looking for a perfect finish to your detail, spray on NANOSKIN HYDRO

EXPRESS. It will not disappoint! Through the use of new nanotechnology formula,

NANOSKIN has created a spray polymer that actually repels water, dissipates

static, lasts up to 2 months, and adds additional protection to your finish.

NANOSKIN HYDRO EXPRESS can also be used on glass, chrome, and plastic.

The spray dries crystal clear on any surface and enhances reflections on shiny

materials, like chrome wheels and trim. It’s so easy, you can detail a full size car in

less than 10 minutes.

Directions:

1. Shake well. Use only on clean, cool paint and out of direct sunlight.

2. Mist HYDRO EXPRESS onto one section at a time.

3. Quickly spread product with clean dry microfiber towel.

4. Turn to a dry portion of the towel, then wipe dry.

16oz

VITALITYNano Spray Wax

• Water-based & silicone free formula


• 2~3 months durability

• Adds anti-static polymer

• Conceals minor scratches and swirl marks

• Protects from harmful UV rays

• Wheel conditioner

NANOSKIN VITALITY is a water-based & silicone free spray wax. The combination

of advanced polymer and nano wax creates a long-lasting brilliant wet-look shine

with outstanding water repellency. Added anti-static polymer will help dust from

settling on the surface. Applying your wheels with VITALITY would also be a great

idea. VITALITY changes the surface polarity of your wheels to repel brake dust

particles.

Directions:


2. Mist VITALITY onto one section at a time.

3. Spread product with clean dry microfiber towel.


16oz

MAJESTICHydrophobic Crème Wax

• Self-cleaning premium wax


• Produces unbelievably deep, vibrant color and a dramatically

clear wet-look

• Protects against oxidation, corrosion, UV rays and

• surface degradation

• Fills and seals fine scratches

• High durability formulation


MAJESTIC is a cream wax designed to add a high gloss and rich luster to new or

used vehicles. MAJESTIC contains nano-sized white carnauba which repels water

excellently and is much more efficient at filling and sealing fine scratches. This

premium wax is a self-cleaning, high durability formulation that is easy to use and

lasts consistent 3-4 months. Hand or machine application work equally well.

Shake well before using.

Directions:


2. For hand application, use a wax applicator in overlapping, circular motion. Allow

to haze, then remove with a clean microfiber towel. Fold in quarters and rotate

often to maximize wax removal efficiency and help prevent scratches.

3. For orbital machine application, wax with slow speed (1200 rpm) and a clean

finishing foam pad.

16oz

HYDROPHOBICNano Paste Wax

• Advanced polymer based nano wax

• Deep gloss & Wet-look

• Water repellent

• Light cleaning properties

• Dries instantly

• Won’t stain trim

• Easy to apply and remove

NANOSKIN HYDROPHOBIC provides relentless water beading, and its nano-sized

polymer with light cleaning properties fills the pores of the paint. With unique nano

tech and formulated white carnauba, HYDROPHOBIC provides warm, wet shine

and deep gloss. Long-lasting hydrophobic effect keeps your ride clean and dust-

free as long as rain drops take dirt away. Apply in any direction you choose. Best

results are simply achieved by applying in very thin coats. As you may notice it

dries instantly. You can remove it immediately, or finish applying it to the rest of

your car.

Directions:


2. Using a clean applicator or soft pad, apply evenly to a section at a time using

overlapping, circular motions.

3. Allow to dry to a haze and wipe off with a clean dry cloth.

4. Buff lightly for a deep gloss shine.

250g

HYDROPHOBIC+Premium Nano Paste Wax

• New hydrophobic polymer formula

• Introduce a new dimension of gloss

• Provides relentless water beading

• Delivers unparalleled shine and protection

• Protects against UV rays and surface degradation

• Easy to apply and remove

NANOSKIN HYDROPHOBIC+ introduces a new dimension of gloss and protection.

It dramatically darkens color, brings out the full richness of the paint, and creates

clear, sharp reflections for the ultimate show car shine. New hydrophobic polymer

formula provides relentless water beading and protection against oxidation,

corrosion, UV rays and surface degradation. This new breakthrough technology

builds such incredible protection and surface tension that water beads up and just

glides off your paint finish, wash after wash!

Directions:


2. Using a clean applicator or soft pad, apply evenly to a section at a time using

overlapping, circular motions.

3. Allow to dry to a haze and wipe off with a clean dry cloth.

4. Buff lightly for a deep gloss shine.

150g

Description:

Nano vehicle wax means the wax which, if applied onto the paint surface or the

metallic stoving varnish on the body, will make it capable of nano characteristics.

Self-cleaning function means that after the nano vehicle wax is applied on the

surface, the water drop contact angle is over 100 degrees, and the body can be

easily cleaned by sponge and clean water.

• Nano vehicle wax shall meet the following requirements:

• Reference Information:

1. ISO 16700:2004(E)：Microbeam Analysis -- Scanning Electron Microscopy --

Guidelines for Calibrating Image Magnification

2. CNS 6928 Method for testing the washability of the latex paint for indoor use

3. ASTM D3836-94(1999)：Standard Practice for Evaluation of Automotive Polish

Performance Standard

Testing Method– See appendix 1 –

• Method for testing nano vehicle wax characteristics for details on testing nano

characteristics.

– See appendix 2 –

• Method for measuring contact angle of water drop for details.


• Method for testing sliding angle of water drops for details.


• Method for testing remaining water drops for details.


• Method for washing test for details on wash durability test.

Appendix 1

Method for testing the nano characteristics of nano vehicle wax

The nano structure formed by applying the wax onto

the vehicle paint surface shall be analyzed by scanning

electron microscopy.

1. Equipment

See ISO 16700:2004 (E): Microbeam Analysis -

Scanning Electron Microscopy - Guidelines for

Calibrating Image Magnification for the

requirements on the microscopy.

2. Preparing the testing piece

The test piece is a piece of painted sheet in the size

of 1cm x 1cm and treated by base, color and

surface coating (clear coat).

Directly apply the vehicle wash wax onto the test

piece for testing; attach the test piece flatly on the

fixer of the scanning electron microscopy; see ISO

16700:2004 (E) for details on preparing the test

piece.

Adjust the magnification rate appropriately to

observe the dimensions of the nano structures

formed on the surface of waxed test piece. (In the

case below, the magnification rate is 50,000X).

3. The principles behind the test

The electron microscopy provides the characteristics

of the nano materials such as the dimensions,

distribution and shape on the basis of the signals

produced by the effect between the electron and

substance. Compared with other methods, in

addition to the direct measurement of the

dimensions, the biggest advantage of microscopy

lies in that the captured images can be used to tell

the in what shape the powder is and it can also be

used on materials with dimensions ranging from

nanometers to microns.

4. Precautions during the test

4.1 The test is a dry test, and do not dip the test

piece into solutons.

4.2 The system must be extracted to vacuum

pressure and anything that can easily

contaminate the vacuum chamber must be

dealt with.

4.3 The testing equipment must be first validated

with traceable standard test piece to ensure its

accuracy.

4.4 The test piece may be gold plated if necessary

to improve its readability in the system.

5. How to present the test results

The test report shall comprise the following:

5.1 Test date/place/instrument model number

5.2 Source of the test piece or the manufacturer

5.3 Treatment conditions before waxing the test

piece

5.4 The hydrophobic structures in the product

specifications must appear and at least one

dimension must be below 100 nm on average,

as shown in Figure A.

Figure A. Analyzing the surface structure on the paint

surface after the nano vehicle wax sold in the market is

applied by electron microscope.

Figure B. Analyzing the surface structure on the

paint surface after the non-nano vehicle wax sold

in the market is applied by electron microscope.

Appendix 3

Method for testing water drop sliding angle

1. Device and equipment

Device for testing water drop sliding: a platform, the

sloping angle of which can be adjusted and thus the

water drop sliding angle can be measured.

The following picture may serve as a reference for

such a platform:

2. Preparing the test piece

The test piece is a white painted plate in the size of

25cm x 50cm and treated with base, color and


3. Treating the test piece

Directly apply the nano vehicle wax on the test piece

and polish it evenly as waxing a vehicle.

4. Test method

Apply a drop of 50 uL volume by a syringe onto the

test plate, adjust the angle for zero degree and

record the angle when the drop begins to slide. The

water sliding degree may be read as precisely as 1

degree.

5. How to present the test results:

The test report should comprise:

5.1 Test date/place

5.2 Source and manufacturer of the painted test

piece.


piece

5.4 Average sliding angle value after the surface is

waxed.

Appendix 4

Method for testing remaining water drops


Use the device for testing sliding water drops shown

in appendix 3 as the reference; however, above the

platform there must be a water storage cup, from

which water can drop.


The test piece is a white painted plate in the size of

25cm x 50cm and treated with base, color and

surface coating (clear coat). The test piece can form

a sliding pathway because one side of the test piece

is about 80 cm longer than the other side.


Directly apply the nano vehicle wax on the test piece

and polish it evenly as waxing a vehicle.

4. Test method

The sloping angle of the testing plate is fixed at 30

degrees. Add 1 ml ink into 1 L water. Adjust the flow

adjustment valve on the cup so that the water can

drop onto the plate at the flow rate of 50 mL/min;

after about half an hour, calculate the percentage of

lattices with remaining water drops in transparent

acrylic plate with one thousand lattices, as shown in

the picture below . Obtain the mean by repeating

the test for three times.



5.1 Test date


piece.


piece

5.4 The average percentage of repetitions of tests

and the lattices where water drops remain.

Appendix 5

Method for washing test for details on wash durability test.


Device for wash durability test: using a device which

meets the provisions in CNS 6928:1981 “Method for

testing wash durability of latex paint for indoor use”.


The painted test piece is a white painted plate in the

size of 5cm x 5cm and treated with base, color and



Directly apply the nano vehicle wax on the test

piece and polish it evenly as waxing a vehicle.

4. Test method

4.1 Fix the test piece onto the platform for wash

durability test.

4.2 Fix a sponge or brush and the friction surface is

kept wet by neutral soap water and frictions the

test piece surface.

4.3 Washing back and forth is counted as one time

the friction times are set at 1000.

4.4 Remove the test piece when the test is

completed, clean it with water, dry it in wind and

measure the contact angle.



5.1 Test date


piece


piece

5.4 The manufacturer and model of the device for

wash durability tests.

5.5 How many times the test piece is washed and

the washing conditions.

Paint Protection

Glass Protection

Wheel Protection




Polishes

Solvents

RAINGlass Sealant

• Water-based formula

• Seals the microscopic pores of glass


• Repels rain, sleet, and snow

• Maintain a high level of visibility

• Significantly improves scratch resistance

• Lasts months, not weeks

RAIN provides a durable, invisible coating to your windshield giving it rain

repellency. The invisible coating repels rain, sleet, and snow to maintain a high

level of visibility, dramatically improving weather driving visibility. The treatment

also makes for easy removal of ice, frost, salt, mud and bugs. RAIN contains

durable anti-static polymer which will help dust from settling on your glass. RAIN

also significantly improves scratch resistance.

ALWAYS USE YOUR WINDSHIELD WIPERS AS NECESSARY.

Directions:

1. Clean with glass cleaner and thoroughly dry surfaces before treating.

2. Mist RAIN onto the surface evenly.

3. Spread product with clean dry lint-free microfiber towel.


5. Reapply RAIN to ensure complete and uniform coverage, then wipe dry.

6. Wait 10~15 minutes, then sprinkle with water or glass cleaner and wipe with a

dry lint-free towel until crystal clear.

16oz, 1Gal

RAIN PLUSHydrophobic Glass Treatment

• Advanced fluorosilane polymer technology

• Exceptional oil & water repellent

• Repels rain, sleet, and snow

• UV resistant

• 12~18 month durability

• Applies to exterior glass

RAIN PLUS is a solvent-based glass treatment by using advanced fluorosilane

polymer technology. The invisible coating provides exceptional oil & water

repellency while maintaining a high level of visibility, dramatically improving

weather driving visibility. With strong UV resistance, the coating has average

12~18 month durability. RAIN PLUS also makes for easy removal of ice, frost,

salt, mud and bugs.


Directions:

1. Clean with ammonia glass cleaner and let it sit on the surface for 3~5 minutes

then wipe off with lint-free glass towel.

2. Mix part A & part B and shake for 90 seconds.

3. Apply mixed product onto the surface , and spread product with non-woven

towel.

4. Allow to haze.

5. Wipe off the haze with lint-free glass towel.

16oz

ANTI-FOGInterior Glass Anti-Fog Treatment

• Eliminates and prevents interior fogging and steaming instantly!


• Windshields, side and rear windows

• Safe for painted surfaces

ANTI-FOG provides a durable, invisible coating to your interior glass preventing it

from fogging and steaming. The invisible coating maintains a high level of visibility,

dramatically improving weather driving visibility. ANTI-FOG contains durable anti-

static polymer which will help dust from settling on your interior glass.

Directions:

1. Clean with glass cleaner and thoroughly dry surfaces before treating.

2. Mist ANTI-FOG onto the surface evenly.

3. Quickly spread product with clean dry lint-free microfiber towel.


5. Reapply ANTI-FOG to ensure complete and uniform coverage, then wipe dry.

6. Wait 10~15 minutes, then sprinkle with clear water and wipe with a dry lint-free

towel until crystal clear.

16oz

ADDITIVEWindshield Washer Fluid/Glass

Cleaner Additive

• Provides residual water beading after use

• Helps revitalize glass sealant

• Improves ordinary washer fluid/glass cleaner performance

ADDITIVE is specially formulated to add to your windshield washer fluid/glass

cleaner. ADDITIVE provides residual water beading after use and helps revitalize

glass sealant. This powerful formula will also help improve ordinary washer fluid

performance to remove stubborn residue, road grime, bird droppings, and tree sap.

General dilution is 1-2 ounces per gallon of washer fluid/glass cleaner.

This bottle shall contain enough additive to treat 12 gallons of washer fluid/glass

cleaner.


Dilution:

4 caps of ADDITIVE to 1 gallon of washer fluid/glass cleaner

Directions:

For Windshield Washer Fluid-

Add 4 caps of ADDITIVE to 1 gallon of “off the shelf” windshield washer fluid.

For Glass Cleaner-

Add 4 caps of ADDITIVE to 1 gallon of “ready to use” glass cleaner.

16oz

Paint Protection

Glass Protection

Wheel Protection




Polish

BRAKE DUSTWheel Protective Shield

• Creates a firm barrier

• Hardens to form a protective shield

• Repels brake dust and road grimes

• Amazing heat resistance


• Spray-on, leave-off


NANOSKIN BRAKE DUST is a scientific breakthrough that introduces a new

dimension of wheel protection. This formula forms an amazing heat resistant

barrier that repels brake dust and road grime. New hydrophobic polymer provides

relentless water beading and protection against conventional acidic wheel

cleaners. This breakthrough technology builds such incredible protection that

wheels stay cleaner longer and clean up easier. A harsh wheel cleaner will no

longer be necessary.

Directions:

1. Clean and thoroughly dry surfaces before treating.

2. Mist BRAKE DUST onto the surface until the surface is fully covered.

3. Allow to dry.

16oz, 1Gal

Paint Protection

Glass Protection

Wheel Protection




Polishes

Solvents

LV RINSELeather & Vinyl Cleaner

• Non-alkaline cleaning agents

• Contains no waxes, oils or additives

• Loosens and suspends the dirt without leaving any deposits or

impediments

• Falls within the Ph range of leather itself.

• Safer for leather

LV RINSE Leather & Vinyl Cleaner is a blend of selected, non-alkaline cleaning

agents designed to clean leather safely and thoroughly without the harshness or

potentially damaging effects of saddle soaps, which are alkaline. The foaming

action loosens and suspends the dirt so that it can be easily rinsed away without

leaving any deposits or impediments. Its balanced formula falls within the pH range

of leather itself, and therefore, is safer for leather. Since it is alkaline-free it

contributes to the prolongation of fiber life.

NOTE: This product is not recommended for napped suede or glove soft leather.

Leather that has cracked from age or neglect cannot be restored by this or any

other known product.

Directions:

1. Remove all loose dirt by vacuuming.

2. Mist a damp towel with LV RINSE and massage into the upholstery. Particularly

soiled areas may require agitation with a white tampico brush or horsehair

brush.

3. Use the cleaner sparingly and do not allow it to dry on the upholstery.

4. Wipe away excess cleaner with a clean, dry microfiber towel.

16oz, 1Gal

NOURISHLeather & Vinyl Cleaner/Conditioner

• One step leather cleaner and conditioner with UV absorber

• Contains the finest natural oils for leather

• Leaves leather soft and supple

• Restores new appearance and natural feel to leather

• Makes scratches and abrasions less visible

• Help penetrates, softens and lubricates leather

• Easy to use: Spray on and wipe off

NOURISH is a one step leather & vinyl cleaner and conditioner. Its unique UV

absorber help protect against premature aging and damage from harmful UV rays.

NOURISH contains the finest natural oils for all type of leather, and it restores new

appearance and natural feel while leaving leather soft and supple. Its liquid

formula conditions and makes scratches & abrasions less visible. NOURISH may

be used on all interior leather, vinyl and plastic.

NOT FOR USE ON NUBUCK OR SUEDE.

Directions:

Use on any color.

1. Always test the product in an inconspicuous area to make sure treated surface

is acceptable.

2. Directly spray onto the leather or apply with clean soft cloth.

3. Brush into leather.

4. Buff gently with soft cloth.

16oz, 1Gal

FEEDLeather & Vinyl Protectant

• Water, oil and stain repellent for finished leathers

• Partially fluorinated polymer

• Exceptional oil, water and alcohol repellency

• Meets all VOC regulations

• Ambient cure

• Little or no effect on appearance of finished leather

• Easy to apply – Gently rub Into leather, wipe off excess

NANOSKIN FEED is a ready‐to‐use cream that protects finished leathers without

altering the feel or appearance of the leather. Unlike many protectors, it does not

leave the leather with an artificial sheen. Its fluorinated polymer provides

exceptional oil, water and alcohol repellency while meeting all VOC regulations.

Apply in a circular motion using a lint free cloth, wiping off any excess after

working it into the leather. FEED may be used on auto interior leather & vinyl,

leather upholstery, leather apparel: shoes, pants, jackets, skirts, luggage,

briefcases and handbags.

NOT FOR USE ON NUBUCK OR SUEDE.

Directions:

1. Working on a clean, dry surface yields the best result.

2. Wipe onto the leather with a soft dry lint-free cloth.

3. Let the product set on leather for approximately 5 minutes.

4. Wipe off excess with soft dry lint-free cloth.

16oz, 1Gal

Before

Left: water drop

Right: cook oil drop

After

Left: water drop

Right: cook oil drop

Performace

Water/Alcohol Repellency Drop Test

(Dupont Test Method)

• Introduction

Repellency was measured by applying 3 drops of

test liquid and observing wetting of the surfaces. If

the drops were repelled for longer than 10 second

the surface was judged to be repellent to that test

liquid.

• Preparations and Treatment of Samples

Test liquids ranged from 2% Isopropyl Alcohol (1

rating) to 50% Isopropyl Alcohol (6 rating)

• Test Method

The higher the concentration of Isopropyl Alcohol

(higher number rating), the more repellent the

surface.

• Analysis Result

All leathers repelled 50% Isopropyl Alcohol and

were rated a 6 in water repellency.

Oil Repellency Drop Test

(AATCC Test Method 118-1989)

• Introduction

Repellency was measured by applying 3 drops of

test liquid and observing wetting of the surfaces. If

the drops were repelled for longer than 30 seconds

the surface was judged to be repellent to that test

liquid.

• Preparations and Treatment of Samples

Test liquids ranged from mineral oil (1 rating) to

Decane (6 rating).

• Test Method

The higher the number test liquid, the more

repellent the surface. Decane (6 rating) is more

difficult to repel than Dodecane (5 rating), which is

more difficult than Tetradecane (4 rating) and so

forth.

• Analysis Result

All leathers repelled at least a 4 oil and most

repelled a 5 or a 6 oil with the average of all

surfaces tested equal to 5.3 out of 6.

BLACK AWESOMEVRT Dressing & Protectant

• Silicone-free, water-based formula

• produces an incredibly deep, rich high gloss shin

• provides long-lasting UV absorber and water proof

• Imparts high gloss to vinyl, rubber, tire, plastic, leather, wood

and stone

• Dilutes up to four to one, varying the gloss from high to satin

• Vinyl, rubber, tire, plastic, leather, wood and stone.

• Clear coat safe

BLACK AWESOME is the choice for professionals or end-users looking for a high

performance dressing which can be used in any silicone sensitive environment. Its

VOC compliant water based formula produces an incredibly deep, rich high gloss

shine. By using advanced polymer, it provides long-lasting UV absorber and

actually repels water each time you clean your car. Dilute up to four to one, varying

the gloss from high to satin. One product, multiple uses...vinyl, rubber, tire, plastic,

leather, wood and stone.

Dilutions:

Tire (High gloss) RTU ~ 1 : 1

Tire (Satin gloss) 1 : 1 ~ 2 : 1

Leather, Vinyl, Rubber & Plastic 2 : 1 ~ 3 : 1

Wood & Stone 3 : 1 ~ 4 : 1

Directions:

1. Dilute one part of product up to four parts of water.

2. Spray directly on the surface or toweling and apply evenly to avoid streaking.

3. Wipe off excess.

16oz, 1Gal

WET LOOKTire Dressing

• Silicone based dressing

• Super high shine

• Tire, rubber moldings & bumpers

• Quick dry, low sling-off formula

• Highlights your great looking investment

• Works great on wet tires

You have waxed and polished your vehicle, removed stains and odors and looked

after the upholstery and leather. Now it's time to tackle the shine of your tires.

Nothing gets noticed more quickly after waxing than your glossy tires. NANOSKIN

WET LOOK Tire dressing is a super high shine, silicone based, dressing for

exterior surfaces. Brush or sponge application is recommended. Quick dry, low

sling-off formula works great on wet tires. WET LOOK really completes "the look“

that auto detailers want.

Directions:

1. For best results, apply to a clean, dry surface.

2. Spray or wipe on surface and let dry to a beautiful shine.

16oz, 1Gal

Paint Protection

Glass Protection

Wheel Protection




Polishes

Solvents

FABRICFabric & Carpet Protector

• Creates a protective finish

• Effectively resists soils and stains

• Safe for all types of fabrics and fibers

• Water & oil repellent

• Dries quickly

• Spray-on, leave-off

• Home, office, boat, auto, and many other applications

NANOSKIN FABRIC is a professional strength treatment that creates a protective

finish that effectively resists soils and stains. It is safe for all types of fabrics and

fibers including silk and sisal. Soils and spills simply blot from the surface. FABRIC

is easy to use, and the solvent formulation dries quickly. Perfect for use wherever

your valuable investments need to be protected from stains and spills: in the

home, office, boat, auto, and many other applications.

Directions:

1. Apply to any new or cleaned fabric.

2. Test fabric for color stability before use.

3. Hold applicator 8 to 10 inches away and spray in a sweeping motion.

4. Do not saturate. A light coating is all that is needed.

5. Allow 1 hour drying time before using treated fabric.

NOTE: FABRIC will migrate (spread) and penetrate fabric extremely well. Over

saturation will result in prolonged drying time.

16oz, 1Gal

Prepare a chamois

Center treated with FABRIC

After cured, put into a tray with water

Apply several water drops & oil drops

onto the treated center area

Left 4 drops: water drop

Right 7 drops: oil drop

Applications

• Test fabric for color stability before use.

• Spray evenly until fabric is slightly damp to the

touch.

• May be applied after immediately after wet or dry

cleaning.

• After application, allow fabric to dry before use.

• Product will cure in 2 stages.

– Stage one at 24 hours.

– Stage two at 72 hours.

• After curing, protector will last 30-40 dry cleanings.

Coverage per gallon

Performance

Carpet Drapery

Low Pile 1200-2400

sq. feet

Light

Weight

1500-3000

sq. feet

Medium Pile 1000-2000

sq. feet

Medium

Weight

1150-2300

sq. feet

High Pile 800-1600

sq. feet

Heavy

Weight

800-1600

sq. feet

Upholstery-

One pint (16oz) covers an average 6 foot sofa

Why is oil repellency important?

At one time or another our carpet or fabrics come in

direct contact with oils, whether it’s oil from our shoes,

cooking oil from our stoves, or body oil from our skin.

NANOSKIN FABRIC is formulated to repel oil helping to

keep the fabric cleaner for a longer period of time. We

believe, as some industry and university studies

indicate that silicone treatments can cause the fabric or

carpet to re-soil at a much faster rate.

Why is UV absorber important?

As you can see when the wave lengths reach the point

that they become visible light (around 380). The

absorbers do not modify (absorb) them or it would

cause the light to be a different color. It is very

important not to block the light or the colors of the

carpet / fabric or it would appear different then its

intended color. For example, instead of a sofa looking

green it may in fact look light blue.

UV Scan

• Harmful UV rays are in the 250 - 350nm range.

• As you can see from the graph, we're showing

absorption from the 190 to 370nm range as noted

by the red line.

• This test was run with a 1% solution of FABRIC with

UV absorber.

• The reason we could not run it with 100% product

is because it absorbed so much that it would be off

the top of the chart and you wouldn't be able to see

anything but a flat line across the top of the chart.

LIQUID IRONWrinkle Release

• Relaxes fibers

• Allows for wrinkle to be easily smoothed away

• Ideal for heat-sensitive fabrics where cool ironing is

recommended

• Anti-static spray & fabric softener

LIQUID IRON Wrinkle Release is a water-based fabric treatment that is effective in

reducing wrinkles in most fabrics. This pH neutral, color safe treatment can be

sprayed on casual clothes for hang drying to reduce wrinkles, or can be applied

during ironing to give clothing a pressed appearance without being stiffened by

starch.

Directions:

Use before or after drying.

Water sensitive fabrics (such as silk or rayon) should be tested first in an

inconspicuous area.

To effect less wrinkling on fabrics in the drying cycle, spray fabrics as they are

transferred from the washer.

In Hang Drying Application-

Simply hold the fabric no more than 1 foot from the spray applicator, and apply

lightly with a sweeping motion to the wrinkled area.

Use more spray for heavy fabrics or severe wrinkling.

For Severe Wrinkling-

Some smoothing of the fabric by hand or with a cold iron will remove wrinkles

faster and more effectively. Fabrics which have been dried and show wrinkling can

be treated and dried at low heat to remove wrinkles quickly and completely.

16oz

Paint Protection

Glass Protection

Wheel Protection




Polishes

Solvents

BUBBLE BATHHydrophobic Shampoo

• Super-concentrated

• Dilution 127 : 1

• Added hydrophobic polymer protection


• Extremely slick

• Nice glossy finish

• Will not strip wax

NANOSKIN BUBBLE BATH is a super concentrated wash solution for all type of

paint finishes. Its hydrophobic polymer formula lubricates the surface, deepens

gloss and leaves a highly water repellent surface. BUBBLE BATH will not remove

wax, yet easily washes away all traces of grease, dirt and grit that have

accumulated since your last wax. BUBBLE BATH works extremely well at cutting

through road salt and winter grime. General dilution is 1 ounce per gallon of water.

Directions:

1. Mix 1 oz per gallon of water.

2. Rinse surface with water to flush away loose dirt.

3. Wash and rinse in sections.

4. Begin with the roof, and work the suds down to the hood, trunk and sides.

5. Rinse with clean water.

6. Dry with clean and soft towels.

For Automatic Car Wash Systems-

1. Dilute 1 gallon of BB to 10 gallons of water.

2. Adjust metering system for maximum foam and cleaning performance.

16oz, 1Gal

GREASE FREEGlass Sealant

• Water-based formula

• Cleans engines, trunks, door jams, wheels, tire

and rims

• Safe for most under-the-hood rubber and plastic parts

GREASE FREE is a concentrated water base power cleaner and degreaser. It

dilutes with water and cleans a variety of surfaces. For engines and greasy door

jams, dilute one part of GF with three parts of water. For medium duty degreasing,

dilute one part of GF with nine parts of water. For general cleaning, dewaxing or

other light duty work, dilute one part of GF with nineteen parts of water. Safe for

most under-the-hood rubber and plastic parts. Great for stubborn spots and stains.

Dilutions:

Heavy Duty Degreasing 3 : 1

Medium Duty Degreasing 9 : 1

General Cleaning, Dewaxing 19 : 1

Directions:

1. Dilute with water to designed strength.

2. Spray or wipe on surface.

3. Brush or wipe as needed.

4. Rinse surface with water.

16oz, 1Gal

BRIGHTWheel, Tire & Metal Cleaner

• Removes grease, road grime, light oxidation and brake dust

• Safe on all types of tires and wheels

• Non-corrosive to skin and metal

• Removes water spots, safe for glass & paint

• No guess work anymore

BRIGHT is a low Ph organic salt that performs like an acid. It is non-corrosive to

skin and metal per DOT/TDG test protocol, non-fuming and is DOT “Non-

Regulated”. BRIGHT safely removes grease, road grime, light oxidation, and brake

dust from metal, paint and other hard surfaces. Safe on all types of wheels

including clear coated, painted, aluminum, polished and anodized. Great for

removing water spots. New technology chemically embraces and lifts mineral

deposits and protect surface from future water spots.

NOTE: BRIGHT can be used to replace HCL acid in many applications and offers

significant performance advantages vs. acids such as phosphoric, citric,

hydroxyacetic, sulfamic, oxalic, etc. with regards to removal of calcium, lime and

rust.

Dilutions:

Wheels & Rims 9 : 1

Water Spot Remover 9 : 1

Diamond Plate 9 : 1

Car & Truck Washing 250 : 1

Directions:

1. Eye protection is recommended. 2. Test an inconspicuous spot for surface

compatibility. 3. Spray even on cool, dry surface. 4. Allow to soak for 1 to 4

minutes. 5. For extremely dirty wheels and tires, agitate with a soft brush or

sponge. 6. Stand away from surface and hose off thoroughly with strongly

water spray. 7. Dry surface immediately with a clean, soft towel to prevent

water spots.

16oz, 1Gal

CRYSTAL-CLEARVOC Free Glass Cleaner

• VOC Free

• Contains no harmful or harsh chemicals, including

ammonia or alcohol

• Uses an ultra-fine polishing agent

• No streaks, no smears

• Safe for glass, ceramics, stainless steel, acrylics, paint surfaces,

polystyrene, ABS and polycarbonate

CRYSTAL-CLEAR highly concentrated VOC Free Glass Cleaner contains no

harmful or harsh chemicals, including ammonia or alcohol that damages your car

or the environment. By using an ultra-fine polishing agent, it gently removes dirt

and grime from glass and clear plastic by polishing it away. The final result is a

polished finish without streaks or smears. Safe for use on glass, ceramics,

stainless steel, acrylics, paint surfaces, polystyrene, ABS and polycarbonate.

Dilution:

40 : 1

Directions:

1. Dilute with water to designed strength.

2. Spray or wipe on surface.

3. Wipe with a clean dry towel or glass towel for a sparkling clean surface.

TIPS: All glass cleaners are sensitive to dirty towels. So, if you use a towel that's

previously been used for polishing or waxing, remaining product residue is bound

to leach out and smear your glass. Dedicated glass towels are your best bet.

16oz, 1Gal

UPHOLSTERYInterior Cleaner & Shampoo

• Superior anti-stain, anti-resoiling properties

• Helps to keep the surfaces cleaner and stain free longer

• Removes oil, grease, dirt, blood, wine, coffee and most

substances

• Cleans soil and spots without removing the natural sheen of any

fine finish

• May also be used on automotive trunk or home carpet

• Environmental friendly

• Biodegradable

UPHOLSTERY Interior Cleaner and Shampoo cleans all interior surfaces without

harmful effects. Specially designed for today’s surfaces, UPHOLSTERY offers

superior anti-stain, anti-resoiling properties helping to keep the surfaces cleaner

and stain free longer. It removes oil, grease, dirt and most substances that stain all

automotive interior surfaces, trunk or home carpet. Using unique cleaning

technology, the best part is that the carpet or fabric will not be altered after

cleaning.

Dilutions:

Pre-Spray 15 : 1 (8oz per gallon)

Extraction Cleaner 63 : 1 (2oz per gallon)

Spot Remover 7 : 1 (16oz per gallon)

Hard Surface Cleaner 127 : 1 (1oz per gallon)

Directions:

Dilute with water to designed strength. 1. Remove all loose dirt by vacuuming.

2. Apply UPHOLSTERY and agitate. 3. Use a carpet cleaning brush for stubborn

spots. 3. Wipe with clean dry towels or vacuum with a WET/DRY vacuum.

4.Allow to air dry.

16oz, 1Gal

When you see the DfE label on a product,

what does it mean?

• EPA allows safer products to carry the Design for the Environment (DfE) label. This

mark allows consumers to quickly identify and choose products that can help

protect the environment and are safer for families.

• When you see the DfE logo on a product it means that the DfE scientific review

team has screened each ingredient for potential human health and environmental

effects and that-based on currently available information, EPA predictive models,

and expert judgment-the product contains only those ingredients that pose the least

concern among chemicals in their class.

• Product manufacturers who become DfE partners, and earn the right to display the

DfE logo on recognized products, have invested heavily in research, development

and reformulation, to ensure that their ingredients and finished product line up on

the green end of the health and environmental spectrum, while maintaining or

improving product performance.

• EPA's Design for the Environment Program (DfE) has allowed use of their logo on

over 2000 products. These products are formulated from the safest possible

ingredients and have reduced the use of "chemicals of concern" by hundreds of

millions of pounds.

How do I know products bearing the DfE label

are really safer?

• Looking carefully at product ingredients

DfE starts with information that scientists already know about each ingredient such

as how it works in a detergent, and how it affects living things. Where that

information doesn't tell the full story, EPA looks at an ingredient's chemical structure

- its components and shape - to understand how it could impact the environment

and people. A chemical's structure can tell a lot about how the chemical will behave

and what types of effects it may have when it comes in contact with people or the

environment. DfE uses the special skills of the scientists at EPA who have studied

chemicals for 30 years or even longer.

• Allowing logo for best in class products only

DfE compares an ingredient's characteristics to other chemicals in the same class.

That is, solvents are compared to other solvents, and wetting agents (surfactants)

are compared with other surfactants. Before DfE allows the logo on a product, DfE

makes sure that only the safest ingredients from each class are used.

• Protecting your family and the environment

When you use a cleaning product, it is released into the environment-inside your

home and down the drain to the outdoors. Adults come in contact with cleaning

products on a regular basis, as do children who are often the most exposed when

they crawl on the floor. Some consumers may prefer cleaning products that, for

example, are inherently safer or do not irritate sensitive skin. Others may prefer

products that break down quickly and do not harm fish or are safer for use around

family pets. The DfE logo is an easy way to know you are choosing a product that is

as safe as possible for people and the environment.

• Expect the safest possible ingredients

When the DfE logo appears on a product, it means that the DfE review team has

screened each ingredient in the product for potential human health and

environmental effects and that--based on hazard and risk information, the latest

models and predictive tools, and expert scientific judgment--the product contains

only those ingredients that pose the least concern among chemicals in their class.

For example, if a DfE-recognized product contains a surfactant, then that surfactant

will not be toxic to human health and it will biodegrade readily to non-polluting

degradation products; many surfactants in conventional products biodegrade slowly

or biodegrade to more toxic and persistent chemicals, which threaten aquatic life.

• DfE formulator review is especially discriminating and protective

The DfE Program is unique because of two defining characteristics: its assessment

methodology and its technical review team. The DfE technical review team has

many years of experience and is highly skilled at assessing chemical hazards,

applying predictive tools, and identifying safer substitutes for chemicals of concern.

The review team applies the DfE assessment methodology by carefully reviewing

every product ingredient (The review includes all chemicals, including those in

proprietary raw material blends, which manufacturers share with DfE in

confidentiality).

SMOOTHInstant Detail Spray

• Missing link between washing and waxing

• Restores the brilliance of a showroom finish

• A clay lubricant

• Can be used on glass, chrome, and plastic

• Enhance reflections on shiny materials


If you’re looking for a missing link between washing and waxing, spray on

NANOSKIN SMOOTH. It removes minor contaminants, dust, fingerprints, bugs,

and more, restoring the brilliance of a showroom finish. As a good friend of clay

bar, SMOOTH lubricates the paint so well while rubbing the clay back and forth. It

can also be used on glass, chrome, and plastic. The spray dries crystal clear on

any surface and enhances reflections on shiny materials, like chrome wheels and

trim. It’s so easy and you can detail a full size car in less than 10 minutes.

Directions:


2. Mist SMOOTH onto one section at a time.

3. Quickly spread product with clean dry microfiber towel.


16oz

WATERLESSWaterless Wash

• Spray, wipe, shine, protect

• Water-based & enviro-friendly

• Removes bugs, dirt, road grime & contaminants

• Designed for paint, glass, chrome & plastic

• Works well at cutting through road salt and winter grime


WATERLESS is a water-based, enviro-friendly blend of wetting agents, emulsifiers

and protectants. It emulsifiers, lifts and remove bugs, dirt and light to medium

surface contaminants. Not for excessively soiled, muddy or caked on dirt.

Designed for all exterior surfaces. Works on all paint, metal, plastic, chrome and

glass. Does not smear or streak. Perfect shine in seconds.

Directions:

1. Spray on surface and let set for 10 seconds.

2. Wipe off with a clean, dry terry cloth or microfiber.

3. For difficult spots, repeat and let soak on surface longer to work, then wipe off.

4. When towels are soiled, use a clean towel.

16oz

SILVER BULLETAll Metal Cleaner & Polish

• Restores mirror bright shine of all types of metals in seconds

• Wheels - Rims – Chrome – Diamond Plate

• Cleans plastic headlights

• Safe for painted surfaces.

SILVER BULLET is the perfect all metal cleaner & polish. It removes minor

scratches and dullness. It restores the sparkle and shine to Aluminum, Brass,

Chrome, Copper, Gold, Magnesium, Pewter, Silver, and Stainless Steel. SILVER

BULLET cleans plastic headlights and restores the clear, bright appearance. Safe

for painted surfaces.

Directions:

1. Shake well before using.

2. Apply a small amount on a soft cloth and rub on surface until it becomes black.

3. Buff of polish residue to an amazing Silver Bullet shine.

4. Repeat if necessary on badly tarnished or oxidized surfaces.

16oz

ESSENCEOdor & Stain Eliminator

• Deodorizes bad odors, not an odor mask

• Removes stains caused by pet urines, wine and some yellow

stains

• Provides anti-resoiling protection

• Safe on wool

• Wide variety of applications


ESSENCE is not only an odor eliminator but also a stain remover. It deodorizes

bad odors caused by spilled milk souring, smoke lingering, or pet odors, not an

odor mask or cover, and it’s Safe on Wool. ESSENCE also removes stains caused

by pet urine, perfume, wine and some yellow stains. Apply directly to stains as

soon as possible to help prevent permanent damage to carpet or fabric dyes.

Directions:

Odors are primarily trapped in fibers, so apply to carpets, upholstery and other

fabric surfaces.

For Odor-

1. Spray light coat evenly over affected areas until surface is damp. Do not

saturate.

2. Allow product to penetrate and self-dry, no rubbing required.

For Stain-

1. Mist Essence onto the surface.

2. Blot with absorbent toweling.

3. Flush with water if necessary.

16oz

Paint Protection

Glass Protection

Wheel Protection




Polishes

Solvents

HD CUTHD Rubbing Compound

• Removes 1000 to 1500 sanding marks

• Prepares surfaces for wax or glaze

• Contains no wax or silicone

NANOSKIN HD CUT is a super fast acting compound that removes 1000 to 1500

grit sanding marks, heavy oxidation, and other serious paint imperfections and

defects from all types automotive paint surfaces. It contains no silicone, no wax,

and no fillers.

Directions:

Shake well. Apply to a cool surface.

Hand-

1. Apply a small amount on a clean, soft cloth.

2. Rub on surface using light pressure to desired finish.

3. Wipe off excess with a clean, soft cloth or micro fiber towel.

Machine-

1. Apply to buffing pad and biff with light to medium pressure to desired finish.

2. Wipe off excess with a clean, soft cloth or microfiber towel.

16oz, 1Gal

FIRST CUTPolishing Compound

• Removes sanding marks and paint defects

• Contains no silicone, wax, or fillers

• Safe for all paints

NANOSKIN FIRST CUT is the first step compound to remove sanding marks,

oxidation, and paint defects from all automotive paints. It's unique combination of

diminishing gentle abrasives, fine polishing powders, and chemical cleaning

agents, deliver a low dust application. The perfect first step set up for

NANOSKIN COMPOLISH Ultra Fine Polishing compound. It contains no silicone,

no wax, and no fillers.

Directions:

Shake well. Use only on clean, cool paint and out of direct sunlight.

Hand-

1. Apply a small amount to a soft cloth and rub on the surface until the scratches

are removed.

2. Wipe off residue and apply wax or glaze.

Rotary Polisher-

1. Apply a small amount to the surface.

2. Buff with a wool or foam pad at low rpm.

3. Slightly tilt up the pad and buff from side to side to remove scratches.


DA or Orbital Polisher-

1. Apply a small amount to the surface and polish until swirls are removed.


16oz, 1Gal

COMPOLISHUltra Fine Polishing Compound

• The enemy of swirls

• Safe for all paints

• Prepares surface for waxing or glazing

NANOSKIN COMPOLISH is an ultra fine polishing compound designed to remove

minor scratches, swirls, spider webs and light oxidation. By simply using

COMPOLISH with 2 pads – Wool polishing pad & Euro foam cutting pad, the paint

will be completely swirl and hologram free. It leaves low dust and produces a

brilliant high gloss finish. A perfect follow up to NANOSKIN FIRST CUT. The

combination of FIRST CUT and COMPOLISH should be all you need for most

paint corrections. It contains no silicone, no wax, and no fillers.

Directions:

Shake well. Use only on clean, cool paint and out of direct sunlight.

Hand-

1. Apply a small amount to a soft cloth and rub on the surface until the scratches

are removed.


Rotary Polisher-

1. Apply a small amount to the surface.

2. Buff with a wool or foam pad at low rpm.

3. Slightly tilt up the pad and buff from side to side to remove scratches.


DA or Orbital Polisher-

1. Apply a small amount to the surface and polish until swirls are removed.


16oz, 1Gal

HI GLAZEHigh-Endurance Glaze

• See the difference

• Feel the shine

• Perfect for all colors and all paints

NANOSKIN HI GLAZE is our top of the line high gloss paint glaze. It is a long

lasting and detergent resistant protectant. It's perfect for all colors and all paints.

On dark colors, the depth of the shine and wet gloss reflections will amaze you.

It's easy application and low dust removal make it a number one choice for

professional detailers. Works in the sun.

Directions:

Shake well before using.

Hand-

1. Apply a small amount to a dry wax applicator sponge.

2. Wipe on surface and let dry to a light haze.

Wipe off residue with a clean dry towel or clean dry micro fiber.

Machine-

1. Apply a small amount product to surface and buff with a foam polishing pad to

a brilliant shine.

2. Wipe off residue with a clean dry soft towel or clean dry micro fiber.

16oz, 1Gal

Paint Protection

Glass Protection

Wheel Protection




Polishes

Solvents

TAR SOLVENTTar & Grease Remover

• Removes tar and adhesive trim marks

• Safe to use on all paints and trim

• Small amount required to remove spots

When oil based, greasy, sticky stains happen, NANOSKIN TGR Tar and Grease

Remover is the answer. This special blend of solvents will remove most oily stains

with ease. In addition to gum, tar, and grease, this stain remover is excellent on

crayon, lipstick, shoe polish, wax, inks, adhesives, glues and many other oil based

stains.

Directions:

Test surface compatibility on an inconspicuous area before using.

1. Lightly moisten a clean cloth.

2. Lightly rub surface to remove undesirable coating.

3. Not recommended for freshly painted surfaces.

4. Do not use on plastic.

16oz, 1Gal

nanoskin car care products 2011

Documents

protective shield glass

protective film

experimental painted

b b hb f h

protective shield109

film hardness

contact angle measurements

contact angle increment