nationalaccreditation boardfor testingandcalibration · pdf fileis1786:2008...
TRANSCRIPT
"RBLNational Accreditation Board for
Testing and Calibration Laboratories(An Autonomous Body under Department of Science & Technology, Govt. of India)
CERID'ICATE OFACCREDITATION
TCR ADVANCED ENGINEERING PRIVATE LIMITEDhas been assessed and accredited in accordance with the standard
ISO/lEe 17025:2005/IGeneral Requirements for the Competence of Testing & Calibration Laboratories"
for its facilities at250-252/9, GIDC, Makarpura, Naren Hardware Lane, Vadodara, Gujarat
inthe discipline ofMECHANICAL TESTING
(To see the scope of accreditation of this laboratory, you may also visit NABL website www.nabl-india.org)
Certificate Number T-1331
Valid Until 13/10/2017Issue Date 14/10/2015
This certificate remains valid for the Scope of Accreditation as specified in the annexure subject tocontinued satisfactory compliance to the above standard & the additional requirements of NABL.
Signed for and on behalf of NABL .
~Anil ReliaDirector
Prof. S. K. JoshiN. VenkateswaranProgram Manager Chairman
HflBLSCOPE OF ACCREDITATION
Laboratory TCR Advanced Engineering Private Limited, 250-25219, GIDC,Makarpura, Naren Hardware Lane, Vadodara, Gujarat
Accreditation Standard ISO/IEC 17025: 2005
Issue Date 14.10.2015
Valid Until 13.10.2017
Page 1 of 3
Test Method Specificationagainst which tests areperformed
Range of Testing ILimits of Detection
Discipline Mechanical Testing
Certificate Number T-1331
Last Amended on 26.10.2015
S.No. Product IMaterial of Test
Specific Test Performed
[. MECHANICAL PROPERTIES OF MATERIALS
1. Metallic Material Tensile TestUltimate Tensile strengthProof stressYield StressReduction in areasElongationLoad Test
Bend Test
Brinnel Hardness Test
Vickers Hardness Test
Rockwell Hardness Test
Micro Hardness Vickers
Charpy V notch impact Test(+)30 °C to (-)196 "C)
Gaurav SainiConvenor
ASTM A370-14,ASTM E8-15a,IS 1608: 2005,EN 10002: 2001,ASME (Sec IX): 15,EN 15614-1: 2008
0.5 kN to 600 kN
ASTM A 370-14,ASTM E 190-14,ASTM E 290-14,IS 1599: 2012,EN 5173: 2010,ASME (Sec IX): 15
ASTM E 10-15,IS 1500: 200.5
4,6,10,12,17,20,24,25,32,40,44,50,55,60mm mandrel dia
100 I-rBWto 400 HBW2.5/187.532 to 125 HBW 2.5/62.5100 to 400 HEW 10/3000100 to 400 HEW 5/750
IS 1501 (Part 1): 2013,ASTM E 384-11
40 to 800 HV5100 to 1000 HVIO100 to 1200 HV 3030 to 100 HRA30 to 100 HRB20 to 70 HRC40 to 1000 HVLoad 25 ,50, 100, 200,300,500,1000 gms2 J to 350 J
IS 1586: 2000,ASTM E 18-15
IS 1501 (Part I):2013,ASTM E 384-11
ASTM E23-12,ISO 148-2: 2008,EN 10045: 1990
N. VenkateswaranProgram Manager
rtflBLSCOPE OF ACCREDITATION
Laboratory TCR Advanced Engineering Private Limited, 250-25219, GIDC,Makarpura, Naren Hardware Lane, Vadodara, Gujarat
Accreditation Standard ISOllEe 17025: 2005
Discipline. Mechanical Testing Issue Date 14.10.2015
Certificate Number T-1331 Valid Until 13.10.2017
Last Amended on 26.10.2015 Page 2 of 3
S.No. Product I Specific Test Performed Test Method Specification Range of Testing IMaterial of Test against which tests are Limits of Detection
performed
2. Metallic Materials Micro Examination:General Structure ASTME 407-07, Grain Size: 1 to 14ASTMGrain size ASTME 3-11,
ASTME 1351:96ASTMA247: 10ASTM E 112- 13
Thickness of coating ASTMB 487 (RA2013) 0.01 rnmto 0.8 mm
Macro etchTest ASTME 340-15, QualitativeASTMA381 (RA 2005)EN ISO 17639:2013
De carburizationDepth ASTME1077-14, 0.01 mmto 0.8 mmIS 6396: 2000 (RA 2007).
Quantative Metallography ASTME-562-11 I %to 99%LOD= 1%
Linear Measurements TCRlADVrrM-37 Rev 03 dated 0.001 mm to 10mm05/10/2015
3. Reinforcement Bend Test of reinforcementbar . IS 1786:2008 4,6,10,12,17,20,24,BarrrMT Bar Rebend test of reinforcementbar 25,32,40,44,50,55,
ITMTbar 60 mmmandrel dia
4. Metallic material FlatteningTest ASTMNSA 370-14, OD(Tubes / Pipes.) ASTMB 11I-II 6 mm to 250 mm
5. Nuts Proof Load ASTMNSA 370: 14, 0.1 kN to 600 kNASTMNSA 194: 15,IS 1367(Part 6): 1994(RA 2004)
Gaurav SainiConvenor
N. VenkateswaranProgram Manager
HflBLSCOPE OF ACCREDITATION
Laboratory TCR Advanced Engineering Private Limited, 250-252/9, GIDC,Makarpura, Naren Hardware Lane, Vadodara, Gujarat
Accreditation Standard ISO/IEC 17025: 2005
Discipline Mechanical Testing Issue Date 14.10.2015
Certificate Number T-1331 Valid Until 13.10.2017
Last Amended on 26.10.2015 Page 3 of 3
S.No. Product I Specific Test Performed Test Method Specification Range of Testing IMaterial of Test against which tests are Limits of Detection
performed
6. StudlBolts FULL Size 8reaking! Tensile ASTM NSA 370-14, 0.1 kN to 600 kNtest/Proof load ASTM NSA 193-15,
IS 1367 (part 3): 2002,
7. Tube to Tube sheet Pull out test/push out test ASME (Sec VIll) Div-I: 2013 O. I kN to 600 kNMock up
8. Ferrous Material Nodularity in SOl iron IS 1754: 2002 Qualitative
9. Wrought Metallic Inclusion rating ASTM E45-13 QualitativeMaterials Method A
Method D
10. Stainless Steel IGCTEST ASTM A 262-14, QualitativePractice A DIN 3651-1 & 2: 1998
Practice 8 ASTM A 262-14, QualitativeDIN 3651-1 & 2: 1998
Practice C ASTM A 262-14, QualitativeDIN 3651-1 &2: 1998
Practice E ASTM A 262-14, QualitativeDIN 3651 -1 & 2: 1998
Pitting corrosion method A ASTMG48-11 QualitativeCrevice corrosion method 8
Inter metallic phase in Duplex ASTM A 923-14 o to 350 Jaustenitic/ferritic stainless steel ASTM A 923Method A ASTM A 923Method 8Method C
11. Metallic & Non Salt Spray Testing ASTM 8-117-11 QualitativeMetallic Materials IS 9844:1981 (Ra 2006)
ISO 9227:2012
-x-x-x-x-x-x-x-x-x-x-x-x-x-x-
N. VenkateswaranProgram Manager
Gaurav SainiConvenor