natspec template web viewthis branded worksection template has been developed by natspec in ......

06 FINISH 0411 Waterproofing – external and tanking

0671P VALSPAR - WATTYL PAINTING

1 GENERAL

1.1 RESPONSIBILITIES

GeneralRequirement: Provide coating systems to substrates, as documented.

PerformanceRequirement: Provide WATTYL coating systems as follows:

- Consistent in colour, gloss level, texture and dry film thickness.

- Free of runs, sags, blisters, or other discontinuities.

- Paint systems which are fully opaque or at the documented level of opacity.

- Clear finishes at the level of transparency consistent with the product.

- Fully adhered.

- Resistant to environmental degradation within the manufacturer’s stated life span.

1.2 COMPANY CONTACTS

Wattyl technical contactsWebsite: www.wattyl.com.au/en/contact-us/index.html

1.3 CROSS REFERENCES

GeneralRequirement: Conform to the following:

- 0171 General requirements.

1.4 STANDARDS

PaintingGeneral: To the recommendations of those parts of AS/NZS 2311 referenced in this worksection.

1.5 MANUFACTURER'S DOCUMENTS

Technical manualsProduct Data Sheets: www.valsparprofessional.com/productfinder/

System Selector Wizard: www.valsparprofessional.com.au/valspec/

1.6 INTERPRETATION

DefinitionsGeneral: For the purposes of this worksection the definitions in AS/NZS 2310 and the following apply:

- Gloss: The optical property of a surface, characterised by its ability to reflect light specularly.

- Gloss unit: Numerical value for the amount of specular reflection relative to that of a standard surface under the same geometric conditions.

- Levels of gloss finish: When the specular direction is 60 degrees, surfaces with the following specular gloss reading is defined as follows:

. Full gloss: Over 85 gloss units.

. Gloss: Between 50 and 85 gloss units.

© NATSPEC (Apr 18) 1 "[Insert date]"

http://www.wattyl.com.au/en/contact-us/index.html


. Semi-gloss: Between 20 and 50 gloss units.

. Low gloss (low sheen): Between 5 and 20 gloss units.

. Flat finish (matt): Up to 5 gloss units.

- Opacity: The ability of a paint or textured and membrane coating to obliterate the colour difference of a substrate.

- Paint or coating system: A product in liquid form, which when applied to a surface, forms a dry film having protective, decorative or other specific technical properties.

- Primer, prime coat: The first coat of a painting system that helps bind subsequent coats to the substrate and which may inhibit its deterioration.

- Sealer: A product used to seal substrates to prevent the following:

. Materials from bleeding through to the surface.

. Reaction of the substrate with incompatible top coats.

. Undue absorption of the following coat into the substrate.

- Substrate: The surface to which a material or product is applied.

- Undercoat: An intermediate coat formulated to prepare a primed surface or other prepared surface for the finishing coat.

1.7 SUBMISSIONS

Products and materialsGeneral: Submit the following at least 3 weeks before the paint is required:

- Paint brand name and product range quality statement.

- Safety data sheets (SDS) showing the health and safety precautions to be taken during application.

- The published recommendations for maintenance.

SamplesClear finish coatings: Submit samples of timber or timber veneer matching those to be used in the works as follows:

- Requirement: Label for identification and prepare, putty, stain, seal and coat in conformance with the documented system.

- Size: Large enough to be cut into 4 segments.

Opaque coatings: Submit labelled samples of each coating system, on representative substrates, showing surface preparation, colour, gloss level, texture, and physical properties.

Coated samples scheduleSubstrate Paint system Colour Sample size

SubcontractorsSpecialist applicators: Submit name and contact details of proposed specialist applicators.

Evidence of experience: [complete/delete]

Wet samplesGeneral: Submit two clearly labelled, 500 mL samples of each type of paint to be tested.



Wet samples schedulePaint type Colour

WarrantiesGeneral: Submit the coating manufacturer’s warranties as follows:

- [complete/delete]

1.8 INSPECTION

NoticeInspection: Give notice so that inspection may be made of the following:

- Painting stages:

. Completion of surface preparation.

. After application of final coat.

- Clear finishing stages:

. Before surface preparation of timber.

. Completion of surface preparation.

. After application of final coat.

- Fireshield coating stages:

. After application of Fireshield TimberClear 1FR.

. After application of Fireshield TimberClear 1FR Top coat.

2 PRODUCT

2.1 GENERAL

Product substitutionOther products: Conform to PRODUCTS, GENERAL, Substitutions in 0171 General requirements.

Storage and handlingGeneral: Store materials not in use in tightly covered containers in well-ventilated areas with temperatures maintained at the manufacturer’s recommendations.

Product identificationGeneral: Marked to show the following:

- Manufacturer’s identification.

- Product brand name.

- Product type.

- Quantity.

- Product reference code and batch number.

- Date of manufacture.

- Material composition and characteristics such as volatility, flash point, light fastness, colour and pattern.



2.2 PAINTING MATERIALS

StandardsPaint types: Conform to the Australian Standard as referenced in the Wattyl paint type table.

Wattyl paint type tableGeneric paint type

Valspar product Technical Data Sheet (TDS)

Paint reference AS/NZS 2311 Table 4.2

Australian Standard

Flat latex: interior Interior Design i.d Contemporary Matt (Low VOC)

D4.54 B6 AS 3730.1

Interior Design i.d Ceiling White (Low VOC)

D4.58 AS 3730.1

Interior Design i.d Advanced Contemporary Matt (Low VOC, Anti-Bacterial & Anti-Mould)

D4.95 AS 3730.1

Solver Ultra Ceiling High Opacity White (Low VOC)

FC-4315.01 AS 3730.1

Solver Brite-Glo Scenic Flat Acrylic (Poster Black) & (Low VOC)

FC-4608.01

Solver Ultra Interior Matt Acrylic

FC-4365.01 AS 3730.1

Professional Choice Ceiling White (Low VOC)

D9.32 AS 3730.1

Permopave Non-Slip

D4.34

Rapidline TM13.30 AS 4049.3

Low sheen latex: interior

Interior Design i.d Luxury Low Sheen (Low VOC)

D4.17 B7 AS 3730.3



Generic paint type



Australian Standard

Interior Design i.d Advanced Luxury Low Sheen (Low VOC, Anti-Bacterial & Anti-Mould)

D4.93 AS 3730.3

Solver Ultra Clean Air Low Sheen Acrylic (Low VOC)

FC-4385.01 AS 3730.3

Solver Ultra Low Sheen Acrylic

FC-4375.01 AS 3730.3

Professional Choice Low Sheen Acrylic

D9.20 AS 3730.3

Satin latex: interior Interior Design i.d Silky Satin (Low VOC)

D4.18 B8 AS 3730.2

Interior Design i.d Advanced Silky Satin (Low VOC, Anti-Bacterial & Anti-Mould)

D4.94 AS 3730.2

Solver Ultra Interior Satin Acrylic

FC-4395.01 AS 3730.2

Professional Choice Satin Acrylic

D9.21 AS 3730.2

Aqua Trim Satin D4.65 AS 3730.2

Gloss latex: interior Aqua Trim Gloss D4.64 B9 AS 3730.12

Flat latex: exterior Solagard Masonry Matt

D4.41 B6 AS 3730.8

AS 3730.16

Duraguard Matt FC-4505.01 AS 3730.16

GranoShield Matt G2.27 AS/NZS 4548.1



Generic paint type



Australian Standard

Permopave Non-Slip

D4.34

Rapidline TM13.30 AS 4049.3

Low gloss latex: exterior

Solagard Low Sheen

D4.14 B7 AS 3730.8

Duraguard Low Sheen

FC-4290.01 AS 3730.16

GranoImpact G2.01 AS/NZS 4548.3

Weathergard Decking Paint

D5.53

Satin latex: exterior Solagard Satin D4.66 B8 AS/NZS 3750.9

Duraguard Satin FC-4520.01 AS 3730.16

GranoSkin Membrane

G2.14 AS/NZS 4548.3


Gloss latex: exterior

Solagard Gloss D4.1 AS 3730.10

Duraguard Gloss FC-4750.01 AS 3730.16

Aqua Trim Gloss D4.65 B9 AS 3730.12

Satin latex interior trim


Gloss latex interior trim

Aqua Trim Gloss D4.64 B42 AS 3730.12

Satin solvent-borne: interior

Solver Ultra Satin Enamel

FC-4212.01 B3 AS 3730.5

High gloss solvent-borne: interior

Ultra Premium High Gloss Enamel

D4.38 B5 AS 3730.6

Permopave Floor & Paving Paint

D4.08



Generic paint type



Australian Standard

High gloss solvent-borne: exterior

Solver Ultra High Gloss Enamel

FC-4220.01 B5 AS 3730.6, AS/NZS 3750.22

Killrust Epoxy Gloss Enamel

D4.59

Solver Roof & Structural Micaceous Paint

FC-4220.01

Permopave Floor & Paving Paint

D4.08

Wood primer, solvent-borne

Solver Ultra Fast Dry Undercoat

SU-4210.01 10 AS 3730.13

Solver Ultra All-Purpose Undercoat

SU-4206.01

Wood primer, latex AquaPrep Acrylic Timber Primer

D3.23 B10A AS 3730.17

Solver Ultra Primer Sealer Undercoat – PSU (Low VOC)

SU-4320.01 AS 3730.17

AS 3730.18

Concrete and masonry sealer, water borne

GranoPrime G1.02 B15

Concrete and masonry sealer, solvent borne

GranoPrime S G1.03 B15

Concrete, masonry, wallboard sealer/undercoat-latex, water borne

Interior Design Acrylic Sealer Undercoat (Low VOC)

D3.18 B16 AS 3730.18

Solver Ultra Acrylic Sealer Undercoat (ASU) (Low VOC)

SU-4325.01 AS 3730.18

Solver Preps Acrylic Plaster

SU-4360.02



Generic paint type



Australian Standard

Sealer (Low VOC)

Professional Choice Acrylic Sealer Undercoat (Low VOC)

D9.05 AS 3730.18

Concrete, masonry, wallboard sealer/undercoat-latex, solvent borne

Master Prep Pigmented Sealer

D3.21 B16 AS 3730.22

Undercoat, solvent-borne

Master Prep Multi Purpose Undercoat

D3.22 B17 AS 3730.14

Solver Ultra Fast Dry Undercoat

SU-4210.01

Solver Ultra All-Purpose Undercoat

SU-4206.01

Undercoat, latex: interior

AquaPrep Primer Sealer Undercoat (Low VOC)

D3.24 B17A AS 3730.18

Interior Design i.d Acrylic Sealer Undercoat (Low VOC)

D3.18 AS 3730.18

Solver Ultra Primer Sealer Undercoat – PSU (Low VOC)

SU-4320.01 AS 3730.17

AS 3730.18

Undercoat, latex: exterior

Interior Design i.d Acrylic Sealer Undercoat (Low VOC)

D3.18 B17A AS 3730.18

Solver Ultra Acrylic Sealer Undercoat (ASU) (Low VOC)

SU-4325.01 AS 3730.18

Solver Ultra Primer Sealer Undercoat –

SU-4320.01 AS 3730.17



Generic paint type



Australian Standard

PSU (Low VOC) AS 3730.18

Metal primer, water borne

Aqua Prep Galvanised Iron Primer

D3.26 AS 3730.15

Solver Preps Galva-Link

PR-4106.01 AS 3730.15

Metal primer, solvent borne

Killrust Etch Primer D2.08

Killrust Heavy Duty Primer

D2.11

Master Prep Metal Primer

D2.13

Solver Preps Zinc Phosphate Anti-Corrosive Metal Primer

PR-4120.01 AS/NZS 3750.19AS/NZS 3750.20

Clear varnish for timber floors, water borne (Low VOC): interior

ESTAPOL Water Based Speed Clear Gloss

D5.54

ESTAPOL Water Based Speed Clear Satin

D5.54

Clear varnish for timber trim, water borne (Low VOC): interior

ESTAPOL Water Based Xtra Clear Gloss

D5.58

ESTAPOL Water Based Xtra Clear Satin

D5.58

Two-pack clear gloss floor finish: interior

Estapol 7008 D5.07 B20 AS 3730.27

Clear varnish for timber trim: interior

ESTAPOL Moisture Cure Polyurethane High

D5.61



Generic paint type



Australian Standard

Gloss

Wood Stain for floors, water borne (Low VOC): interior

Colourwood flooring stain

D5.57

Wood Stain for trim, water borne (Low VOC): interior

Colourwood Water Based Stain and Varnish Gloss

D5.24

Transparent polyurethane varnish for timber decking & walls: exterior

Weathergard Decking 2-in-1 Stain & Varnish

D5.49

Decking paint for timber: exterior

Weathergard Decking Paint

D5.53

Transparent decking oil paint for timber: exterior

Weathergard Water-based Decking Oil

D5.52

Wattyl low VOC paint tableProduct Type Valspar products VOC gm/litre Tinted

Walls and ceilings – Interior Semi-Gloss

Interior Design Silky Satin < 1

Walls and ceilings – Interior Semi-Gloss

Interior Design i.d Advanced Silky Satin

< 1

Walls and ceilings – Interior Low Sheen

Interior Design Luxury Low Sheen

< 1


Interior Design i.d Advanced Luxury Low Sheen

< 1


Solver Ultra Interior Premium Clean Air Acrylic

< 3

Walls and ceilings Interior Flat-Washable

Interior Design i.d Contemporary Matt

< 1



Product Type Valspar products VOC gm/litre Tinted

Walls and ceilings Interior Flat-Washable

Interior Design i.d Advanced Contemporary Matt

< 1

Ceilings – Interior Flat Interior Design i.d Ceiling White < 1

Ceilings – Interior Flat Solver Ultra Ceiling Premium High Opacity White

< 3

Ceilings – Interior Flat Professional Choice Ceiling White

< 10

Trim – Interior Gloss Aqua Trim Gloss < 45

Trim – Interior Semi-gloss Aqua Trim Silky Satin < 74

Timber Primer Aqua Prep Acrylic Timber Primer < 30

Timber Primer Solver Ultra Primer Sealer Undercoat – PSU

< 20

Binding Primer Solver Preps Acrylic Plaster Sealer

< 5

Latex primer for galvanized iron and zincalume

AquaPrep Galvanised Iron Primer

< 10

Latex primer for galvanized iron and zincalume

Solver Preps Galva-Link < 60

Interior Latex Undercoat Interior Design Acrylic Sealer Undercoat

< 1

Interior Latex Undercoat Solver Ultra Acrylic Sealer Undercoat – ASU

< 45

Interior Latex Undercoat Solver Ultra Primer Sealer Undercoat – PSU

< 20

Interior Latex Undercoat Professional Choice Acrylic Sealer Undercoat – ASU

< 65

Interior Sealer Solver Ultra Acrylic Sealer Undercoat – ASU

< 45

Interior Sealer Solver Ultra Primer Sealer Undercoat – PSU

< 20

One pack performance coatings ESTAPOL Water Based Speed < 135



Product Type Valspar products VOC gm/litre Tinted

for floors Clear Gloss-Satin

One pack performance coatings for floors

ESTAPOL Water Based Xtra Clear Gloss-Satin

< 75

Trim – Exterior Gloss Solagard Gloss < 73

Trim – Exterior Low Sheen Solagard Low Sheen < 55

Trim – Exterior Semi Gloss Solagard Satin < 60

Exterior Latex Undercoat Solver Ultra Primer Sealer Undercoat – PSU

< 20

CombinationsGeneral: Do not combine products from different manufacturers in a system.

Clear timber finish systems: Provide only the combinations of putty, stain and sealer recommended by the manufacturer of the topcoats.

Putty and fillersMaterial: To the recommendations of the paint system manufacturer, suitable for the substrate and compatible with the primer.

TintingGeneral: Provide only products which are colour tinted by the manufacturer or supplier.

Toxic ingredientsGeneral: To the Poisons Standard March 2018 (including SUSMP 20) Part 2 Section 7.

3 EXECUTION

3.1 PREPARATION

Order of workOther trades: Before painting, complete the work of other trades as far as practicable within the area to be painted, except for the installation of fittings, floor sanding and laying flooring materials.

Clear finishes: Complete clear timber finishes before commencing opaque paint finishes in the same area.

ProtectionGeneral: Before painting, clean the area and protect it from dust contamination. Use drop sheets and masking agents to protect surfaces, including finished surfaces and adjacent finishes, during painting.

Fixtures and furniture: Remove door furniture, switch plates, light fittings and other fixtures before painting, and conform to the following:

- Labelling and storage: Attach labels or mark fixtures using a non-permanent method, identifying location and refixing instructions, if required. Store and protect against damage.

Difficult to remove fixtures: Where removal is impractical or difficult, apply surface protection before substrate preparation and painting.



Wet paint warningNotices: Place in a conspicuous location and do not remove until the paint is dry.

Substrate preparation – generallyGeneral: Prepare substrates to receive the painting systems.

Cleaning: Clean down the substrate surface. Do not cause damage to the substrate or the surroundings.

Filling: Fill cracks and holes with fillers, sealants, putties or grouting cements as appropriate for the finishing system and substrate, and sand smooth.

- Clear finish: Provide filler tinted to match the substrate.

Clear timber finish systems: Prepare the surface so that its attributes will show through the clear finish without blemishes, using methods including the following:

- Removal of bruises.

- Removal of discolourations, including staining by oil, grease and nailheads.

- Bleaching where necessary to match the timber colour sample.

- Puttying.

- Fine sanding, with the last abrasive no coarser than 220 grit, so that there are no scratches across the grain.

Treated surfaces: If surfaces have been treated with preservatives or fire retardants, make sure coating is compatible with the treatment and does not adversely affect its performance.

Unpainted surfacesStandard: To AS/NZS 2311 Section 3.

Previously painted surfacesCondition of substrate: [complete/delete]

Location of substrate in good condition: [complete/delete].

Location of substrate in poor condition: [complete/delete].

Preparation of a substrate in good condition: To AS/NZS 2311 clause 7.4.

Preparation of a substrate in poor condition: To AS/NZS 2311 clause 7.5.

Preparation of steel substrates with protective coatings: To AS 2312.1 Section 8 and AS 1627.1.

PVC-U: Clean with methylated spirit and a nylon scouring pad.

Wallcovering: Remove wallcovering and residual paste with clean water. Patch and repair substrate to a uniform surface before painting.

Lime wash paints: Remove by brushing with warm water.

Reconditioned damaged surfaces in galvanized steel: To AS/NZS 4680 Appendix E.

Cleaning external surfacesSound external surfaces other than timber: Remove dirt, grease, loose and foreign matter, efflorescence and mould by water blasting or steam cleaning without damaging the surface. Remove remaining loose material with appropriate hand tools. Use sanding blocks to preserve the arrises of masonry and stone details.

Efflorescence: Eliminate the source of salt and water before cleaning. Allow surface to dry for 15 to 30 days before repainting.

New masonry: Allow 30 days for the masonry to cure and pH level to stabilise before painting.

Particular preparation requirements schedule



Substrate Preparation method Applicable standard

3.2 PAINTING

Light levelsGeneral: ≥ 400 lux.

Substrate moisture contentRequirement: Use a moisture meter to demonstrate that the moisture content of the substrate is at or below the recommended maximum level for the type of paint and the substrate material.

Painting conditionsGeneral: Unless the paint is recommended for such conditions, do not paint under the following conditions:

- Dusty conditions.

- Relative humidity: > 85%.

- Surface temperature: < 10°C or > 35°C.

Priming before fixingGeneral: Apply one coat of wood primer, and 2 coats to end grain, to the back of the following before fixing in position:

- External fascia boards.

- Timber door and window frames.

- Bottoms of external doors.

- Associated trims and glazing beads.

- Timber board cladding.

SandingClear finishes: Sand the sealer using abrasives no coarser than 320 grit without cutting through the colour. Take special care with round surfaces and edges.

SprayingGeneral: If the paint application is by spraying, use conventional or airless equipment which conforms to the following:

- Satisfactorily atomises paint being applied.

- Does not require paint to be thinned beyond the maximum amount recommended by the manufacturer.

- Does not introduce oil, water or other contaminants into the applied paint.

Paint with known health hazards: Provide personal protection, masking, ventilating and screening facilities to AS/NZS 4114.1 and AS/NZS 4114.2.

RepairRequirement: Clean off marks, paint spots and stains progressively and restore damaged surfaces to their original condition.

Maintenance painting: To AS/NZS 2311 Section 8.



Repair of galvanizingCleaning: For galvanized surfaces which have been subsequently welded, power tool grind to remove all surface contaminants, including rust and weld splatter. Prime affected area immediately after cleaning.

Primer: Type 2 organic zinc-rich coating for the protection of steel to AS/NZS 3750.9.

TintingGeneral: Tint each coat of an opaque coating system so that each has a noticeably different tint from the preceding coat, except for top coats in systems with more than one top coat.

ServicesGeneral: Paint all new services and equipment, including those in plant rooms, if not embedded, except chromium, anodised aluminium, GRP, PVC-U, stainless steel, non-metallic flexible materials and normally lubricated machined surfaces.

Proprietary items: Repaint only if damaged.

WindowsOperation: Make sure opening windows function correctly before and after painting.

DoorsDrying: Maintain door leaf in the open position during drying. Do not allow door hardware or accessories to damage the door finish during the drying process.

3.3 COMPLETION

CleaningGeneral: On completion of painting, remove splatters by washing, scraping or other methods which do not scratch or damage adjacent finished surfaces.

Reinstatement: Repair, replace or refinish any damage, including works of other trades. Touch up new damaged decorative paintwork or misses only with the paint batch used in the original application.

Fixtures: Refix removed and undamaged fixture in the original location, make sure they are properly fitted and in proper working order.

Protection and maskingGeneral: Remove masking and protection coverings before paint has dried.

Disposal of paint and waste materials.Requirement: Conform to requirements of the local government authority.

4 SELECTIONS

4.1 PAINTING SYSTEMS

GeneralNumber of coats: Except where one or two coat systems are documented, each paint system consists of at least 3 coats.

Final coat selection: To the INTERIOR PAINTING SCHEDULE and the EXTERIOR PAINTING SCHEDULE.

Low VOC emitting paintsGeneral: Provide the VOC limits as documented in the Interior painting schedule and the Exterior painting schedule.

Previously painted surfacesStandard: To AS/NZS 2311 Tables 8.2 and 8.3.

Other requirements: Apply the following:



- Sealer: [complete/delete]

- Undercoat: [complete/delete]

Specialised painting systemsStandard: To AS/NZS 2311 clause 5.2. Provide the following final coats:

- High build textured or membrane finishes for concrete and masonry: B38 using products conforming to the AS 4548 series.

- Two-pack gloss pigmented polyurethane: B44.

- Two-pack epoxy: B29.

- Two-pack water based epoxy: B29A.

4.2 COLOUR RANGE

Paint colours scheduleSubstrate Number of colours

4.3 INTERIOR PAINTING SCHEDULE

Ultra premium interior (Low VOC)Paint code Substrate Final coat Painting system Colour reference

Previously Painted Water Based Acrylic Finishes

Interior Design i.d Ceiling White

WAU1001.2

Paper-Faced Plasterboard


WAU1001.4

Hard Set Plaster (Water-Based Primer)


WAU1001.7.2

Brickwork Blockwork


WAU1001.8

Off-Form Concrete (OFC)


WAU1001.10

Fibre Cement Sheet (FCS)


WAU1001.11



WAU1002.2



Paint code Substrate Final coat Painting system Colour reference



WAU1002.4



WAU1002.7.2

Brickwork Blockwork


WAU1002.8

Cement Render Interior Design i.d Contemporary Matt

WAU1002.9



WAU1002.10



WAU1002.11

Tilt-Up And Pre-Cast Concrete


WAU1002.12


Interior Design i.d Luxury Low Sheen

WAU1003.2



WAU1003.4

Timber Interior Design i.d Luxury Low Sheen

WAU1003.5



WAU1003.7.2

Brickwork Blockwork


WAU1003.8

Cement Render Interior Design i.d Luxury Low Sheen

WAU1003.9



WAU1003.10



WAU1003.11






WAU1003.12


Interior Design i.d Silky Satin

WAU1004.2



WAU1004.4

Timber Interior Design i.d Silky Satin

WAU1004.5



WAU1004.7.2

Brickwork Blockwork


WAU1004.8

Cement Render Interior Design i.d Silky Satin

WAU1004.9



WAU1004.10



WAU1004.11



WAU1004.12

Ultra premium Interior (Low VOC) water based enamelPaint Code Substrate Final coat Painting system Colour reference

Shop primed steel Aqua Trim Silky Satin

WAU1026.3

Plasterboard Aqua Trim Silky Satin

WAU1026.4

Timber Aqua Trim Silky Satin

WAU1026.5

MDF Aqua Trim Silky WAU1026.6



Paint Code Substrate Final coat Painting system Colour reference

Satin

Galvanized steel Aqua Trim Silky Satin

WAU1026.13

Iron and steel Aqua Trim Silky Satin

WAU1026.16

Shop primed steel Aqua Trim Gloss WAU1027.3

Plasterboard Aqua Trim Gloss WAU1027.4

Timber Aqua Trim Gloss WAU1027.5

MDF Aqua Trim Gloss WAU1027.6

Galvanized steel Aqua Trim Gloss WAU1027.13

Iron and steel Aqua Trim Gloss WAU1027.16

Ultra premium interior (Low VOC, anti-bacterial & anti-mould)Paint code Substrate Final coat Painting system Colour reference



WAU1005.2



WAU1005.4

Hard Set Plaster Interior Design i.d Advanced Contemporary Matt

WAU1005.7



WAU1005.7.2

Brickwork Blockwork


WAU1005.8

Cement Render Interior Design i.d Advanced

WAU1005.8




Contemporary Matt



WAU1005.9



WAU1005.11



WAU1005.12



WAU1006.2



WAU1006.4

Timber Interior Design i.d Advanced Luxury Low Sheen

WAU1006.5

Hard Set Plaster Interior Design i.d Advanced Luxury Low Sheen

WAU1006.7



WAU1006.7.2

Brickwork Blockwork


WAU1006.8

Cement Render Interior Design i.d Advanced Luxury Low Sheen

WAU1006.9



WAU1006.10


Interior Design i.d Advanced Luxury

WAU1006.11




Low Sheen



WAU1006.12



WAU1007.2



WAU1007.4

Timber Interior Design i.d Advanced Silky Satin

WAU1007.5

Hard Set Plaster Interior Design i.d Advanced Silky Satin

WAU1007.7



WAU1007.7.2

Brickwork Blockwork


WAU1007.8

Cement Render Interior Design i.d Advanced Silky Satin

WAU1007.9



WAU1007.10



WAU1007.11



WAU1007.12



Ultra premium interiorPaint code

Ultra premium interior enamelPaint code Substrate Final coat Painting system Colour reference

Timber id Ultra Premium Satin Enamel

WAU1051.5

Timber id Ultra Premium High Gloss Enamel

WAU1052.5

MDF id Ultra Premium Satin Enamel

WAU1051.6

MDF id Ultra Premium High Gloss Enamel

WAU1052.6

Shop primed steel id Ultra Premium Satin Enamel

DS 030.11

Shop primed steel id Ultra Premium High Gloss Enamel

DS 035.11

Galvanized steel id Ultra Premium Satin Enamel

WAU1051.13

Galvanized steel id Ultra Premium High Gloss Enamel

WAU1052.13

Iron and steel id Ultra Premium Satin Enamel

WAU1051.16

Iron and steel id Ultra Premium High Gloss Enamel

WAU1052.16

Premium Interior painting low VOC





Solver Ultra Clean Air Low Sheen Acrylic

SAU2004.2



SAU2004.4

Timber Solver Ultra Clean Air Low Sheen Acrylic

SAU2004.5



SAU2004.7.2

Brickwork Blockwork


SAU2004.8

Cement Render Solver Ultra Clean Air Low Sheen Acrylic

SAU2004.9



SAU2004.10



SAU2004.11



SAU2004.12


Solver Ultra Ceiling High Opacity White

SAU2005.2



SAU2005.4



SAU2005.7.2




Brickwork Blockwork


SAU2005.8



SAU2005.10



SAU2005.11

Fibre cement sheet Cement render Concrete

Solver Brite-Glo Scenic Flat Acrylic (Poster Black)

PS-620

Bondek® soffits (galvanized iron)

Solver Brite-Glo Scenic Flat Acrylic (Poster Black)

PS-619

Premium Interior paintingPaint code Substrate Final coat Painting system Colour reference



SAU2001.2



SAU2001.4

Hard Set Plaster Solver Ultra Interior Matt Acrylic

SAU2001.7

Brickwork Blockwork


SAU2001.8

Cement Render Solver Ultra Interior Matt Acrylic

SAU2001.9



SAU2001.10



SAU2001.11



SAU2001.12






SAU2002.2



SAU2002.4

Timber Solver Ultra Low Sheen Acrylic

SAU2002.5

Hard Set Plaster Solver Ultra Low Sheen Acrylic

SAU2002.7

Brickwork Blockwork


SAU2002.8

Cement Render Solver Ultra Low Sheen Acrylic

SAU2002.9



SAU2002.10



SAU2002.11



SAU2002.12



SAU2003.2



SAU2003.4

Timber Solver Ultra Interior Satin Acrylic

SAU2003.5

Hard Set Plaster Solver Ultra Interior Satin Acrylic

SAU2003.7

Brickwork Blockwork


SAU2003.8

Cement Render Solver Ultra Interior Satin Acrylic

SAU2003.9






SAU2003.10



SAU2003.11



SAU2003.12


Ultra Ceiling Toned White

SAU2006.2



SAU2006.4

Hard Set Plaster Ultra Ceiling Toned White

SAU2006.7



SAU2006.10

Premium interior painting enamelPaint code



Trade interior painting low VOCPaint code Substrate Final coat Painting system Colour reference


Professional Choice Ceiling White

WAU1205.2



WAU1205.4

Cement Render Professional Choice Ceiling White

WAU1205.9



WAU1205.10



WAU1205.11

Bondek® soffits (galvanized iron)


WAU1205.13

Trade Interior paintingPaint code Substrate Final coat Painting system Colour reference



WAU1202.2



WAU1202.4

Brickwork Blockwork


WAU1202.8

Cement Render Professional Choice Low Sheen Acrylic

WAU1202.9


Professional Choice Low Sheen

WAU1202.10




Acrylic



WAU1202.11



WAU1202.12



WAU1203.2



WAU1203.4

Brickwork Blockwork


WAU1203.8

Cement Render Professional Choice Satin Acrylic

WAU1203.9



WAU1203.10



WAU1203.11



WAU1203.12

Trade interior painting enamelPaint code Substrate Final coat Painting system Colour reference

Timber Professional Choice Easy Flow Satin Enamel

WAU1207.5




Timber Professional Choice Easy Flow Gloss Enamel

WAU1208.5

Shop primed steel Professional Choice Easy Flow Satin Enamel

WAU1207.3

Shop primed steel Professional Choice Easy Flow Gloss Enamel

WAU1208.3

Galvanized steel Professional Choice Easy Flow Satin Enamel

WAU1207.13

Galvanized steel Professional Choice Easy Flow Gloss Enamel

WAU1208.13

Iron and steel Professional Choice Easy Flow Satin Enamel

WAU1207.16

Iron and steel Professional Choice Easy Flow Gloss Enamel

WAU1208.16

Premium Woodcare clear two pack polyurethane finishesPaint code Substrate Final coat Painting system Colour reference

Timber floors and trim

ESTAPOL 7008 WAU1126.5 Not applicable

Premium Woodcare clear polyurethane finishes low VOCPaint code Substrate Final coat Painting system Colour reference

Timber floors ESTAPOL Water Based Speed Clear Gloss

WAU1127.5 Not applicable

Timber floors ESTAPOL Water Based Speed Clear Satin





Timber trim ESTAPOL Water Based Xtra Clear Gloss


Timber trim ESTAPOL Water Based Xtra Clear Satin


Premium Woodcare clear varnish finishesPaint code Substrate Final coat Painting system Colour reference

Timber ESTAPOL Moisture Cure Polyurethane High Gloss


Premium Woodcare stain and clear timber floor finishes low VOCPaint code Substrate Final coat Painting system Stain colour

Timber ESTAPOL Water Based Speed Clear Gloss

WAU1132.5

Timber ESTAPOL Water Based Speed Clear Satin

WAU1132.5

Premium Woodcare stain and clear finishes low VOCPaint code Substrate Final coat Painting system Stain colour

Timber ESTAPOL Water Based Xtra Clear Gloss

WAU1135.5

Timber ESTAPOL Water Based Xtra Clear Satin

WAU1135.5

Two pack epoxy water based low VOCPaint code Substrate Final coat Painting system Colour reference

Concrete Wattyl EPINAMEL P32.04




CF720

Cement render Wattyl EPINAMEL CF720

P32.04

Two pack epoxyPaint code Substrate Final coat Painting system Colour reference

Concrete Wattyl EPINAMEL EB600

P31.01

Cement render Wattyl EPINAMEL EB600

P31.01

4.4 EXTERIOR PAINTING SCHEDULE

Ultra Premium exterior low VOCPaint code Substrate Final coat Painting system Colour reference


Solagard Masonry Matt

WAU1076.2

Brickwork Blockwork


WAU1076.8

Cement Render Solagard Masonry Matt

WAU1076.9



WAU1076.10



WAU1076.11



WAU1076.12

Galvanized Iron and Zincalume®


DS205.6

Bare Iron and Steel (not galvanized)


DS205.5




PVC Solagard Masonry Matt

DS205.8


Solagard Low Sheen

WAU1077.2

Timber Solagard Low Sheen

WAU1077.5

Brickwork Blockwork

Solagard Low Sheen

WAU1077.8

Cement Render Solagard Low Sheen

WAU1077.9


Solagard Low Sheen

WAU1077.10


Solagard Low Sheen

WAU1077.11


Solagard Low Sheen

WAU1077.12


Solagard Low Sheen

WAU1077.13


Solagard Low Sheen

WAU1077.16

PVC Solagard Low Sheen

WAU1077.17


Solagard Satin WAU1078.2

Timber Solagard Satin WAU1078.5

Brickwork Blockwork


Cement Render Solagard Satin WAU1078.9












Bondek soffits (galvanized iron water based option)




PVC Solagard Satin WAU1078.17


Solagard Gloss WAU1079.2

Timber Solagard Gloss WAU1079.5

Brickwork Blockwork


Cement Render Solagard Gloss WAU1079.9











PVC Solagard Gloss WAU1079.17





Duraguard Matt SAU2101.2

Brickwork Blockwork


Cement Render Duraguard Matt SAU2101.9











PVC Duraguard Matt FC-4505.01


Duraguard Low Sheen

SAU2102.2

Timber Duraguard Low Sheen

SAU2102.5

Brickwork Blockwork

Duraguard Low Sheen

SAU2102.8

Cement Render Duraguard Low Sheen

SAU2102.9


Duraguard Low Sheen

SAU2102.10


Duraguard Low Sheen

SAU2102.11


Duraguard Low Sheen

SAU2102.12





Duraguard Low Sheen

SAU2102.13


Duraguard Low Sheen

SAU2102.16

PVC Duraguard Low Sheen

SAU2102.17


Duraguard Satin SAU2103.2

Timber Duraguard Satin SAU2103.5

Brickwork Blockwork


Cement Render Duraguard Satin SAU2103.9











PVC Duraguard Satin SAU2103.17


Duraguard Gloss SAU2104.2

Timber Duraguard Gloss SAU2104.5

Brickwork Blockwork


Cement Render Duraguard Gloss SAU2104.9














PVC Duraguard Gloss SAU2104.17

Elastomeric coating system - highest performancePaint code Substrate Final coat Painting system Colour reference

Cement render GranoSkin Membrane (Low Profile Finish)

GAU3020.9

Brick and blockwork

GranoSkin Membrane (Low Profile Finish)

GAU3020.8



GAU3020.10

Precast concrete Tilt-up concrete


GAU3020.12

Elastomeric coating system - high performancePaint code Substrate Final coat Painting system Colour reference

Cement render GranoShield Matt (Low Profile Finish)

GAU3030.9

Brick and blockwork

GranoShield Matt (Low Profile Finish)

GAU3030.8






GAU3030.10



GAU3030.12

Elastomeric coating systemPaint code Substrate Final coat Painting system Colour reference

Cement render GranoImpact (Low Profile Finish)

GAU3010.9

Brick and blockwork

GranoImpact (Low Profile Finish)

GAU3010.8



GAU3010.10



GAU3010.12

Compressed fibre cement sheeting


GAU3010.22

ExoTec CFC sheeting


GAU3010.25

Elastomeric coating system – textured finishPaint code Substrate Final coat Painting system Colour reference


GranoImpact (High Profile finish)

GAU3015.10


GranoImpact (High Profile finish)

GAU3015.12

Roll-on texture: High profile, smooth to coarse finishesCoating code Substrate Texture/

intermediate coat

Final coat Coating system

Colour reference

Brick and blockwork

GranoSahara Ripple

GranoImpact GAU3115.8



Coating code Substrate Texture/intermediate coat

Final coat Coating system

Colour reference

Cement render GranoSahara Ripple


Off Form Concrete (OFC)

GranoImpact High Profile



GranoSahara Ripple



GranoSoffit Texture

GAU3050.10


GranoRoll-on Smooth



GranoRoll-on Medium



GranoRoll-on Coarse



GranoImpact High Profile



GranoSahara Ripple



GranoRoll-on Smooth



GranoRoll-on Medium



GranoRoll-on Coarse




Ultra premium exterior (Low VOC) water based enamelPaint code

Ultra premium exterior enamelPaint code

Trade exterior painting enamelPaint code Substrate Final coat Painting system Colour reference

Timber Professional Choice Easy Flow Gloss Enamel

WAU1208.5

Shop primed steel Professional Choice Easy Flow Gloss Enamel

WAU1208.3

Galvanized steel Professional Choice Easy Flow Gloss Enamel

WAU1208.13




Iron and steel Professional Choice Easy Flow Gloss Enamel

WAU1208.16

Premium Woodcare exteriorPaint code Substrate Final coat Painting system Colour reference

Timber Weathergard Decking Water Based Stain

WAU1176.5

Timber Weathergard Decking Paint

WAU1177.5

Timber Weathergard Decking Oi

WAU1178.5

Timber Weathergard Water Based Decking Oi

WAU1179.5

Previously stained, oiled Timber

Weathergard Decking 2-in-1 Stain & Varnish

WAU1180.1

Timber Weathergard Decking 2-in-1 Stain & Varnish

WAU1180.5

Timber Weathergard Exterior Varnish

WAU1181.5

Paving paint water-based slip resistantPaint code Substrate Final coat Painting system Stain colour

Concrete Permopave Non-Slip

D4.34

Asphalt/bitumen Permopave Non-Slip

D4.34

Timber Permopave Non-Slip

D4.34



Linemarking water-basedPaint code Substrate Final coat Painting system Colour reference

Concrete Rapidline TM 13.30

Asphalt/bitumen Rapidline TM 13.30

4.5 ADDITIONAL DATA

Paint system characteristics schedulePaint code Characteristic Requirements


natspec template web viewthis branded worksection template has been developed by natspec in ......

Documents