ncar-tn/str-65 numerical prediction of the performance of ... · performance of high altitude...
TRANSCRIPT
NCAR-TN/STR-65NCAR TECHNICAL NOTE
July 1971
Revised February 1974
Numerical Prediction of thePerformance of High Altitude Balloons
Frank KreithProfessor of Engineering, University of ColoradoandConsultant, National Center for Atmospheric Research
Jan F. KreiderResearch Associate, University of ColoradoandConsultant, Environmental Consulting Services, Inc.
ATMOSPHERIC TECHNOLOGY DIVISION
NATIONAL CENTER FOR ATMOSPHERIC RESEARCHBOULDER, COLORADO
iii
PREFACE
Originally issued in 1971, this report was prepared to assist in
predicting the vertical motion of high altitude balloon systems. In
anticipation of the increasing use of balloons as an energetically
efficient means of transporting instrumentation or commercial payloads,
it seemed desirable to enlarge the report to include a calibrated model
for predicting the vertical trajectory of zero-pressure balloons. A
number of errors in the 1971 edition have been corrected in this revi-
sion. The additions in the revised report to the dynamic and thermo-
dynamic analysis contained in the original edition provide the balloon
engineer an efficient, calibrated computer program to predict balloon
ascent rates, ceiling, and behavior at float.
We would like to thank A. L. Morris, J. H. Smalley, and K. H.
Stephan of NCAR for their help and encouragement in the preparation of
the original document.
Frank Kreith
Jan F. Kreider
November 1973
v
CONTENTS
Preface . . . . . . . . . . . . . . . . . . . . . . . . ... a iii
List of Figures .......................... vii
List of Tables . ..... . . . . . . . . .o . ix
Nomenclature . . . o . o . . o . . . . . . xi
Credits . . . . . . . . ... . o . e . . .. . .o . . xiii
I. INTRODUCTION . . . . . . . . . . . . . . . .. . . .. . . 1
II. THE EQUATIONS OF VERTICAL MOTION ............. 3
III. CONVECTION BETWEEN THE ATMOSPHERE AND THEBALLOON SYSTEM . ....... . .......... 13
IV. CONVECTION INSIDE THE BALLOON .......... o 23
V. RADIATION HEAT TRANSFER .... . ... ...... e 25
VI. EMITTED RADIATION . . .................. 33
VII. DIRECT SOLAR RADIATION ............... o 37
VIII. REFLECTED SOLAR RADIATION ................ 43
IX. INFRARED RADIATION FROM THE EARTH AND THEATMOSPHERE ............ .. ...... . 55
X. EXPERIMENTAL RESULTS ... . . . . . . . .. 69
Appendix .... . . . . . . . . . . . . . .. . . . . . . 77
References ........ . . . . . . . . . . . . . . 125
vii
FIGURES
1. Schematic illustrating force balance for verticalballoon motion ....... .......................... . 4
2. Temperature variation in the atmosphere up to 100 km .... 7
3. Schematic illustrating energy balance for lifting gas
and balloon skin ................. .. 10
4. Local free convection heat transfer over a sphere--
comparison of theory and experiments ............ 14
5. Average Nusselt number for sphere in combined free and
forced convective flow ................... 19
6. Temperature field about a heated horizontal flat plate
at a Rayleigh number of 50 ................. 21
7. Emission of radiation from a balloon skin--
the effective emittance .................. 34
8. Spectral distribution of solar radiation in space
and at sea level ................ ...... 38
9. Spectral distribution of solar radiation incident at
sea level for air masses 1.0 to 8.0 ... 39
10. Albedo as a function of latitude under various
sky conditions ......... ... 45
11. Shape factor for a small sphere and rectangular area .... 48
12. Satellite- or balloon-to-earth geometric configuration . . . 51
13. Variation of directional solar reflectance with
zenith angle (60° < C < 80°) .. ....... .... 52
14. Albedo map for the northern hemisphere during theperiod 16-28 July 1966 ................... 53
15. Variation of directional hemispherical reflectance
with zenith angle ........... . . - 54
16. Infrared radiation map for the northern hemisphere
during the period 16-28 July 1966 ...... . ... 56
17. Upward and downward radiation flux as a function
of altutude .................. *e* e 57
viii
18. Suomi-Kuhn flat plate radiometer ... ......... 61
19. Radiation environment at Green Bay, Wisconsin,in the summer . . .· . , . .... . .. . . . 63
20. Radiation environment at Green Bay, Wisconsin,in the winter ....... , 64
21. Radiation environment at a desert island, 20S . . ., 65
22. Gergen "Black Ball" radiometer ... . ...... . 66
23. Vertical trajectory of "Thermistor" Flight.October, 1964, 250,000 ft 3 polyethylene balloon,He lift gas. Solid line - model prediction; dashedline - data. ...... .... 72
24. Vertical trajectory of Stratoscope S4-2 Flight.July, 1965, 5.5 million ft 3 Mylar balloon, He liftgas. Solid line - model prediction; dashed line -data . .......................... 73
25. Vertical trajectory of Stargazer Flight. December,1962, 3.1 million ft Mylar balloon, He lift gas.Solid line - model prediction; dashed line - data. .... 74
26. Vertical trajectory of Special Hydrogen Flight.July, 1970, 1.5 million ft 3 polyethylene balloon,H2 lift gas. Solid line - model prediction; dashedline - data. .................. .... 75
ix
TABLES
1. Equivalent length dimensions of convection correlation .... 17
2. Average Nusselt numbers for a horizontal plate in freeconvection . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3. Constants for the free convection equation (Eq. 27) ..... 22
4. Constants for free convection in a sphere (Eq. 29) ...... 24
5. Radiation characteristics of surfaces ... .. 30
6. Energy storage capabilities of water and batteries .. . 31
7. Relative spectral distribution of solar radiation under
various sky conditions ........... . ..... 44
8. Mean values of thickness, reflectance, and absorptancefor various cloud types ..... . .... .... . 49
9. Radiation environment for superpressure balloons ....... 59
xi
NOMENCLATURE
A -area
a -absorptance
b - thickness of fabric
CD - drag coefficient
CM - virtual displacement coefficient
c - specific heat at constant volumeV
D -diameter
E exhaust rate of balloon gas through expulsion duct and valve
e - emittance
F -force
G -radiation incident on surface
g -gravitational constant
h -heat transfer coefficient
I - intensity of radiation
LF - free lift
LG - gross lift (= p V - m )
M -molecular weight
m -mass
p -pressure
q -rate of heat transfer
R - universal gas constant
r -reflectance or radial distance
S - surface area
T - temperature
t - time
U -velocity
V -volume
v - specific volume
z -altitude or geopotential height
xii
- zenith angle
y - lapse rate of atmosphere
X- wavelength of radiation
e - polar angle or super temperature
T - superpressure
p - mass density
a - Stefan-Boltzmann constant
T - transmittance
- azimuth angle
Subscripts
a - atmospheric air
B - ballast
b - balloon system
c - convection
D - drag
d - ducting
f - balloon skin fabric
g - balloon gas
i - infrared
o - zero altitude
p - payload
s - solar
v - valve
Dimensionless Numbers
Gr - Grashof Number
Nu - Nusselt Number
Pr - Prandtl Number
Ra - Rayleigh Number
Re - Reynolds Number
Re* - Equivalent Reynolds Number
Sc - Schmidt Number
xiii
CREDITS
Below is a list of the figures used in this report which have been taken
from other publications.
Fig. 2 S. L. Valley, Ed.: Handbook of Geophysicsand Space Environments, McGraw-Hill,New York, N.Y. (Copyright 1966, usedwith permission of McGraw-Hill Book Co.)
Fig. 4 A. A. Krause and J. Schenk: Thermal freeconvection from a solid sphere. AppZ.Sci. Res. A-15. (Copyright 1965, usedwith permission of Martinus Nijhoff, N.V.)
Fig. 5 H. Borner: Heat and mass transfer of singlebodies by combined free and forced convec-tion. VDI-Forschungsheft 512. (Copyright1965, used with permission of VDI-Verlag,Dusseldorf.)
Fig. 6 F. J. Suriano and K.-T. Yang: Laminar freeconvection about vertical and horizontalplates at small and moderate Grashof num-
bers. Int. J. Heat Mass Trans. 11(3).
(Copyright 1968, used with permission of
Pergamon Press.)
Fig. 8 S. L. Valley, Ed.: Handbook of Geophysicsand Space Environments, McGraw-Hill,New York, N.Y. (Copyright 1966, usedwith permission of McGraw-Hill Book Co.)
Fig. 9 D. M. Gates: Spectral distribution of
solar radiation at the earth's surface.Science 151(3710). (Copyright 1968,
used with permission of American Asso-ciation for the Advancement of Science.)
Fig. 10 C. G. Goetzel, J. B. Rittenhouse, andJ. B. Singletary, Eds.: Space Mate-
rials Handbook, 2nd ed., TORML 64-40Air Force Materials Laboratory, Wright-
Patterson Air Force Base, Ohio, 1965.
Figs. E. Raschke: The radiation balance of
13,14 the earth-atmosphere system from radi-
15,16 ation measurements of the Nimbus IImeteorological satellite. NASA TND-4589, Washington, D.C., 1968.
xiv
Fig. 17 T. Sasamori: The radiative cooling cal-culations for application to generalcirculation experiments. J. AppZ.Meteorol. 7(5). (Copyright 1968, usedwith permission of American Meteoro-logical Society.)
Figs. Courtesy of Peter Kuhn, Atmospheric18,19 Physics and Chemistry Laboratory,20,21 Environmental Science Services
Administration, Boulder, Colo.
Fig. 22 J. L. Gergen: "Black-Ball": A devicefor measuring atmospheric infraredradiation. Rev. Sci. Instr. 27(7),1956.
1
I. INTRODUCTION
The vertical motion of balloon systems depends critically on the
heat transfer to and from the gas inside because the temperature and
the pressure of the gas determine the lift of the balloon. In the past
the thermal design of high altitude balloons has largely been based on
a combination of experience, empirical data, and approximate calcula-
tions [1,2]. Recent advances in heat transfer research make it fea-
sible, however, to calculate the temperature of the lifting gas as a
function of altitude and to predict the vertical motion of the balloon
system with the aid of high speed computers [3,4].
Any computer program designed to predict the vertical motion of a
balloon uses equations with coefficients whose values are derived from
theory or experiments. Such a program was developed several years ago
for the Office of Naval Research and has since been used by balloon
manufacturers and the National Center for Atmospheric Research. In
developing the currently available program, several of the heat transfer
and friction coefficients were adjusted to obtain agreement between the
vertical motion and the gas temperatures observed during the flights of
two balloons especially instrumented to obtain these data. Reasonably
good agreement between the computed and the measured performance was
obtained. However, in developing the program the values of several
empirical coefficients were altered simultaneously. Therefore, it is
not possible to discern which coefficients are generally applicable to
scientific ballooning and which are useful only for calculating the
motion of these two specific balloons. To improve the accuracy and
reliability of analytical predictions of balloon motion, the heat trans-
fer and friction parameters in the program should be compared with the
results of recent advances in heat transfer research and, if necessary,
revised.
There are three general problem areas in which thermal design can
improve balloon operation. The first involves rapid variations in
internal energy which occur when clouds cause sudden changes in the
radiation incident on the balloon. This type of change in the heat
2
transfer rate is usually sensed only after the altimeter registers a
change. After an altitude change is registered, altitude is maintained
by dropping ballast or exhausting gas. If one could control altitude
by reacting rapidly to a change in radiation, the loss of ballast or gas
could be reduced. The second area of thermal design is concerned with
changes in heat loss during a complete day. More accurate predictions
of heat loss and the use of appropriate materials or surface coatings
could increase the payload or the float altitude for a given balloon
system. The third area of thermal design involves long-range planning
for balloon flights, such as those currently envisioned in the equato-
rial zone, over new routes.
This report presents first the equations governing the vertical
motion of a balloon. It then reviews recent advances in heat transfer
experimentation and theory pertinent to the processes which affect the
calculation of balloon performance and the thermal design of balloon
instrument packages. Finally, the pertinent equations of fluid mechan-
ics, heat transfer, and thermodynamics are combined to predict analyti-
cally the vertical motion of balloons. The Appendix includes a complete
computer program predicting the vertical motion of balloons; this pro-
gram is based on the analysis given in the body of the report.
3
II. THE EQUATIONS OF VERTICAL MOTION
The total mass of a balloon system which must be accelerated during
ascent and descent, including a virtual mass term CMpaVg to account for
the air mass displaced by the motion of the balloons [5,6], is
Zm. = m + mf + mB + m + CMPaVg (1)i g Pg
where m is the mass of the lifting gas, mf the mass of the balloon fab-
ric, mB the ballast, and m the payload, and where m + mf + m + m = mbp g B p mb
the mass of the balloon system. The sum of the forces acting on the
balloon system (Fig. 1) is
Fi = (PaVg m - mf - mB -m p) - 1/2CDaIblUb (2)
The sum of the five terms in the parentheses times g is usually called
the "free lift," LF. The last term represents the aerodynamic drag
force, FD.
For a spherical shape in the Reynolds-number range of large bal-
loons, i.e., above 6 x 10 5 , the drag coefficient, CD, is equal to 0.1
[7], but no data for actual balloon shapes have been published. In
Ref. 8, a value of 0.3 for C was used as an average for computational
purposes.
In balloon terminology g(p Vb - m ) is called the "gross lift," LG.
Using the perfect gas law as the equation of state for the atmospheric
air and the balloon gas, LG is given by the expression
/M P T + \L /a a a_= gm M P + T (3)
where 0 = (T - T ) is the so-called gas superheat (although it is
actually a super temperature), and T = (P - Pa) is called the gassuperpressure.
superpressure.
dzVELOCITY = Ub = d
mf MASS OF FABRIC
'm--m mg - MASS OF GAS
CMP Vo v IVIRTUAL 1MASS OF BALLOONDUE TO ACCELERATION
mB + m - MASS OF PAYLOAD + BALLAST
7777r GROUNDE Fz = MASS x ACCELERATION
9 [(poV g- mm -m- m p)-CDPo UAb]
2
dt z(mg + mf+mB+mp+C V)o b o v oo oo
Fig. 1 Schematic illustrating force balance for vertical balloon motion.
5
The qualities 0 and T are usually quite small compared to T anda
P , respectively. The ratio of T/P is of the order of 0.0015 in zero-a a
pressure balloons, but may be as large as 0. 25 in superpressure balloons.
The ratio e/T depends on the heat transfer characteristics of thea
system, as discussed in detail in subsequent sections of this paper. By
expanding the fraction in Eq. (3) one can deduce the widely used approx-
imate relation
La g a 1 + a 7F (4)LO = gmg [al+ 8(-~ a)] (4)
G g -- M T-g g a a
Substituting Eqs. (1) and (2) into Newton's second law of motion
gives
F 1 d/2 Ca dt (m + mf + mB + m + C V) (5)LF - p1/2 CD a P - CMPaVpg dt2
In applying the above equations it is possible to relate the balloon
pressure to the height z through the hydrostatic balance and the equa-
tion of state of the atmosphere because there is generally only a very
slight superpressure in a balloon. In zero-pressure balloons this
superpressure is limited by the automatic exhaustion of gas through the
expulsion duct just before float altitude is reached. This gas release
keeps the balloon from bursting. Gas is also released through an
exhaust valve controlled from the ground--"valving"--to reduce the free
lift when the balloon ascends too rapidly and to initiate descent from
float altitude.
ATMOSPHERIC PROPERTY VARIATIONS
In hydrostatic equilibrium the variation of pressure in the atmo-
sphere with altitude is given by the relation
dP
a (6)dz =-gpa
6
If it is assumed that the atmospheric air obeys the perfect gas law,
the pressure as a function of altitude is expressed by
dP Ma a
P = g RT dz (7)a a
or
p ga gMa / dz
in p R / Tao a
zo
Over limited ranges in altitude the variation of the atmospheric air
temperature with altitude is often approximated by the linear relation
a = T + Y (z - z) (8)
where
ay, the lapse rate = d at z)
Figure 2 shows the temperature variation to 100 km as a function of
altitude according to various models of the atmosphere proposed during
the past 15 years [9].
If the atmospheric temperature profile is known (or taken for
purposes of calculation from Fig. 2), the pressure and density varia-
tions over an altitude change between zl and z 2 for which the lapse rate
is a constant can be written in the form
P l a T lgMa ++Ry
a a
2 \Ta 2 \aRPd p (2T) aRY
PRESSURE (mb) p
(D
21. 8l ...... ' - -.
rEOMETRICt -ATITU- (--
-v II ImIC
rtH,. m FJ- /H- -s 0o r,,
*-oiI//rt m
0
~C)~~
0r~r 0S\\/
0 2
0 3)~~~~~~DENSITY (g/m 3 )
8
BALLOON GAS EXPANSION
The variation of the gas volume in the balloon with time is
dV Rm T \ Rm dT RT dm Rm T dPg d g = g + g g _ gg g (10)
dt dt MP MP P dt M P d2 dt\gg g gg MP
gg
If the relation between atmospheric pressure and altitude from Eq. (7)
is used and superpressure is neglected, the above equation can be
written in the form
dVdV / dT dm gm T M d \m _g + T g+g d +dt P dt R dt RT (11
ga a
LIFT AND LOAD ADJUSTMENTS
As mentioned earlier, the lift of a balloon system can be reduced
by exhausting helium automatically through the gas expulsion duct when
float altitude is reached, or by valving to maintain float altitude,
to reduce the rate of ascent, or to cause the balloon to descend. If Ed
is the volumetric gas flow rate through the expulsion duct (required to
stabilize the balloon at ceiling) and E is the flow rate through the
exhaust valve, the net change in balloon mass due to loss of gas is
dm- =p E + p E (12)dt gd d d gv v
The mass of the balloon system can be reduced by dropping ballast
or part of the payload. This change in mass of the balloon system dur-
ing a time increment At = t2 - tl is
2 dmb 2 dm
- dt P
1 1
where Am represents the amount of mass dropped during the time inter-
val At.
9
THE ENERGY EQUATIONS
The conservation equation for the gas inside the skin of a balloon
can be obtained by applying the First Law of Thermodynamics (Fig. 3).
The rate of change of the internal energy of the gas equals the rate at
which heat is transferred to the gas (ql) minus both the rate at which
net work is done by the gas and the rate at which internal energy is
lost by valving. Assuming that the equation of state of the gas can be
approximated by the ideal gas law and that the temperature and pressure
of the gas inside the balloon are uniform, one obtains
RT dm dV dm
dt v g q1 M dt a dt vg dt
where the term on the left-hand side of Eq. (14) is the rate of change
in internal energy of the balloon gas, the first term on the right hand
represents the rate of heat transfer by free convection from the interior
surface of the balloon skin to the gas, the second term the flow work
done during gas release, the third term the work done on the external
pressure when the balloon volume changes because of a change in gas tem-
perature or because of valving, and the last term the loss of internal
energy by valving. If the pressure inside the balloon is uniform and
equal to the atmospheric pressure, the flow work done during valving in
the absence of heat transfer equals the work done by the atmosphere on
the balloon and the second and third terms cancel.
The assumption that the temperature of the gas inside the balloon
is uniform may lead to serious error when short-term transients occur
and the gas adjacent to the balloon skin undergoes temperature varia-
tions while the gas in the interior does not. When this situation pre-
vails, the first term in the energy equation should be replaced by
d--t Cv|c p T dV'(JJJ vggg g
g
A similar analysis can be performed on the balloon skin. The
internal energy of the skin will change only because of heat transfer
ENERGY EQUATION-SKIN ENERGY EQUATION -GAS
FLOW WORK dmg.( pv) ( Volving )dt t
I(( ^ SqSOLAR q 2 - -sKq, /I /j
/ (q CONVECTION
/; qA CONVECTION q4 X Vg C T
q RADIATION q5 q lNFRARED q 3 K COMPRESSION WORK = Pa dVdt
dt- (cpt)fdS, = q 2+q+q 4-q 5 -q,
~Sf~~ ~~ d~~~~dt t dVg. 3 S c ig e y b e for dtl (mT)9 gq- d (PV)g PbA dn.
Fig. 3 Schematic illustrating energy balance for lifting gas and balloon skin.
11
to and from its surfaces. The skin is so thin that one can neglect the
temperature drop across it at any location, but since the heat transfer
over the skin is not uniform its temperature will vary. This variation
cannot, however, be expressed analytically, and when it becomes impor-
tant only a numerical analysis can yield a satisfactory approximation of
the physical reality.
To simplify the thermodynamic analysis it will be assumed that an
averaged skin temperature can be used. A First Law analysis (Fig. 3)
then gives
d fdTfCfff qc+ d + q -q - q (15)dt cf PftfTfdSf = cfmf dt = q2 3 4 q (1 5 )
f
where c = specific heat of skin
mf = mass of skin
Tf = average skin temperature
Pf = density of the balloon skin
q = rate of absorption of solar radiation
2, direct 2, reflected)
q = rate of absorption of infrared radiation3
q = rate of heat transfer by convection from the4 atmosphere to the skin
q = rate of radiant heat transfer from the skin
tf = thickness of film
S = surface area of balloon
q = rate of heat transfer by convection from the1 skin to the lift gas
Equations (14) and (15) are the two energy equations which must be
combined with Eq. (5) to calculate the vertical position and the motion
of the balloon. The energy equations for the balloon gas and the skin
fabric can be treated analytically if one assumes that all of the gas
is at one temperature and the entire skin is at one temperature (these
two temperatures may or may not be identical). This assumption is quite
good at night but can introduce appreciable errors during the day when
solar energy heats the skin unevenly. Modifications for nonuniform
12
heating could be made in the analysis [10] for the exterior of the fab-
ric skin by numerical means, but the convection process inside a non-
uniformly heated, balloon-shaped container is very complex. At this
time the process is not well enough understood to be modeled analyti-
cally; thus an accurate calculation of the heat transfer in the interior
is not possible. Fortunately, during normal flight, balloons rotate so
all parts of their skins are exposed equally (on the average) to the sun
and the balloon gas is mixed. This makes the assumption of uniform gas
and skin temperatures valid for thermal analyses performed for times
ranging from hours to days.
In the following three sections the heat transfer phenomena in bal-
loon systems will be examined in the light of recent advances in heat
transfer research. Sections III and IV will deal with convection and
Sect. V with radiation phenomena. The final objective will be the eval-
uation of the five heat transfer terms in Eq. (15).
13
III. CONVECTION BETWEEN THE ATMOSPHERE AND THE BALLOON SYSTEM
(q in Eq. 15)4
Convective heat transfer between balloon systems and the atmosphere
occurs over wide ranges of the convectional parameters used to describe
the process. Heat is transferred between the atmosphere and the balloon
by forced convection or free convection, or both, at Reynolds numbers
from 0 to 107 and Grashof numbers from 0 to 1011. Depending on the cir-
cumstances, the flow can be laminar or turbulent. The shapes of super-
pressure balloons resemble a sphere, those of zero-pressure balloons
resemble an onion, but instrument packages come in a variety of shapes,
such as cubes, cylinders, and plates. Balloon diameters range from 10
to 400 ft, ascent velocities from near 0 to 40 ft/sec, and temperature
differences (between the skin and gas) from 0 to 50°F.
Although convective heat transfer to and from an object in air has
been studied extensively, few investigations extend into the extreme
Reynolds- and Grashof-number ranges encountered by balloons and none
have specifically treated the onion shape typical of zero-pressure bal-
loons. Therefore, approximations and extrapolations of existing data
are unavoidable.
Heat transfer from spherical shapes in forced convection has
recently been investigated experimentally by Yuge [11] and Vliet and
Leppert [12]. Local values of the heat transfer coefficient in flow
over a sphere in the neighborhood of the stagnation point have been cal-
culated by Merk [13]. The pressure distribtuion for flow over spheres
has been investigated by Fage [14], who also measured the separation
point. He found that at a Reynolds number of 1.6 x 106, separation
occurred at a polar angle ( of 70° (Fig. 4) and moved toward the rear
with increasing Reynolds number. At the highest Reynolds number of his
tests, ReD = 4.2 x 106, separation occurred at a polar angle of 100°.
Extensive correlations of experimental data indicate that in
forced convection the average Nusselt number of the entire surface of
1.0 Nu
(CorPr)V
, , , , , ,--....,..£-. *1
Ir: II/ ,
0.5 / /
°1 . . . . . . . . . .. , .. .
0 60 120 180
OAT =15.50C; "AT=19.5°C
Fig. 4 Local free convection heat transfer over a sphere--comparison of theory and experiments.
15
the sphere in air can be obtained from the relation
hDN c 0.57
Nu = = 2 + 0.30 Re m (16)m k D,m
a
for Reynolds numbers between 1.8 x 103 and 1.4 x 105 [11] or from the
relationh Dc 0.5 5
Nu = = 2 + 0.41 ReD,5 (17)m k D,m
a
for Reynolds numbers between 0.4 and 2 x 105 [12]. In both of the above
equations, the subscript m indicates that all physical properties should
be evaluated at the mean temperature between the skin and the atmospheric
temperatures.
Using Eq. (17), the rate of heat transfer by convection to or from
the surface of the balloon skin during ascent or descent can be written
in the form
q= 3.9 V 1/3 k (T - Tf) 2 + 0.472 V' 3 [a dz/dt ) (18)4 g a a g Oa p^a
Krause and Schenk [15] investigated thermal free convection from a
warmer surrounding fluid to a cooler spherical body at uniform surface
temperature in the range of Rayleigh numbers between 6 x 108 and
5 x 109. As shown in Fig. 4, the experimental results for the local
heat transfer coefficient agree reasonably well with a theoretical
analysis of Merk [16] up the the hydrodynamic separation point, which
for the narrow Grashof-number range of this investigation occurred at a
polar angle of about 145° from the vertical axis. Since Merk's theory
applies equally well for laminar free convection from a heated sphere,
it also seems reasonable to use the data in Fig. 4 to calculate heat
transfer from the upper hemispherical surface of heated balloons. No
theory or data exist at present, however, to predict the influence of
the nonuniform azimuthal temperature distribution, which is always
present when the balloon is heated by the sun.
16
Experimental evidence is contradictory regarding the influence of
the Grashof number on the separation point in laminar free convection to
or from a sphere. Garner et al. [17,18] found a shift in separation
point from 155 to 100° between mass transfer Rayleigh numbers (Gr * Sc)
from 1.5 x 108 to 5.5 x 108 for different fluids with 800 < Sc < 2,200,
whereas Schutz [19] found a much weaker dependency in the region
2 x 108 < Gr * Sc < 2 x 10l° (170 to 135°) for a fluid with Sc = 1,800.
According to conventional boundary layer theory, the separation point
should shift toward the stagnation point with increasing Grashof numbers
and the heat transfer coefficient in the region of the free convection
plume, where the flow is turbulent, will be larger than in the laminar
flow regions, as shown in Fig. 4. The results agree qualitatively with
observations of free convection about a horizontal cylinder.
The point of transition from laminar to turbulent flow in the free
convection regime is not presently known. Schlieren patterns [15] show
that purely laminar flow prevails over a sphere between the stagnation
point and the equator at Grashof numbers as high as 6 x 108 and that
some disturbances exist between 100° and separation (190 to 150°), but
real turbulence was observed only in the plume at a Grashof number of
about 109. Perhaps the stability analysis of Gebhart [20] could be
applied to natural convection over a balloon-shaped body (idealized as
a sphere to analytically predict the point of transition. Gebhart's
analysis for a flat plate predicts that turbulent instabilities could
amplify at local Grashof numbers of the same order of magnitude as have
been observed on balloons.
If the designer can use averaged values of the heat transfer
coefficient over the entire surface of the sphere, available data can
be correlated [15] by a relation of the type
DhNu = c = 2 + 0.6(GrPr)4 (19)m k m
a
for Rayleigh numbers between 105 and 2 x 10l°. The constant value of 2
applies in the limit as the Grashof number approaches zero and the heat
transfer mechanism approaches pure conduction. The theoretical
17
convergence of the Nusselt number at small Grashof numbers has recently
been elegantly verified by Fendell [21].
The influence of vibration on the heat transfer from spheres has
been investigated in free and forced convection [22], and the influence
of rotation about a vertical axis has been studied experimentally for
free convection [23,24]. The results of these investigations indicate
that under flight conditions neither vibration nor rotation will in-
fluence balloon heat transfer characteristics.
Using Eq. (19), the rate of heat transfer by free convection to or
from a balloon at float altitude can be written in the form
p2g(T - T)V \11a = .a a f -
q = 7.79 V 3k (T - Tf) 1 + 0.322 (20)
a a
For computational purposes a very convenient correlation of
averaged experimental convection data has recently been provided by
Borner [25], who reviewed 70 previous investigations of heat and mass
transfer by free convection or forced convection, or both, in flow over
single bodies, and who also conducted additional tests. One convenience
of Borner's correlation is that.data for bodies of different shapes can
be handled [26] by choosing a pertinent length dimension, 9', defined in
Table 1 for several shapes.
Table 1
EQUIVALENT LENGTH DIMENSIONS OF CONVECTION CORRELATION
Shape of Body Equivalent Length A'
Very wide plate with surface parallel to theflow in forced convection with length Z in
direction of flow. R' =
Sphere or long cylinder of diameter D with
axis perpendicular to the flow in forced
and free convection 9' = (T/2)D
Long rectangular bar of width a* andheight b* with its long axis perpendicular
to the flow in forced convection 9' - a* + b*
Vertical plate (surface parallel to gravity)
of height 9 in free convection 9' =
Long horizontal plate (surface perpendicular
to gravity) of width 9 in free convection 9' = Q/2
18
Reference 25 presents correlations of free convection data for plates
(horizontal and vertical), spheres, and cylinders (horizontal and vertical)
as plots of Nu., = h '/k versus (Gr, · Pr) = (gp23ATV'3/p 2) (c p/k)c p
and of forced convection data in the form Nu., versus Reg,. A combined
free and forced convection correlation was obtained by defining an equi-
valent Reynolds number for free convection Rei,*
x2
Reg,* = f(Pr) Gr, (21)
where the function f(Pr) for air, which is dependent upon the Prandtl
number, should be taken equal to f for "a best fit correlation," com-
pared to 0.64 predicted by analysis. With the definition of an equiva-
lent Reynolds number for free convection given in Eq. (21), free convec-
tion dominates when Re., < 2.4 Reg,* and forced convection dominates
when Re.,* < 2.4 Reg,. A transition region, where both free and forced
convection are appreciable, exists between these limits. It has been
shown that in this transition region free convection aids the forced con-
vection transfer when the motion caused by buoyancy is in the same
direction as the forced flow and retards it [27,28] when buoyancy
opposes the flow. In order to bridge the gap between forced and free
convection Borner [25] defines a third Reynolds number Re'g, as
Re' Re, + (Gr,/2) (22)
and then plots Nu., versus Re' ,. Figure 5 shows the results of this
correlation for a sphere with downward forced convection, the situation
of an ascending balloon. Under these circumstances free convection will
oppose the forced convection flow, but visualization studies for this
condition [25] have shown that the existence of a free convection field
will produce turbulence at low velocities and will also cause separation
of the boundary layer. These effects tend to offset any decrease in
the heat transfer, as predicted for purely laminar flow [27]. The
correlation function shown in Fig. 5 was also found to be applicable
for upward flow, the condition of a descending balloon. Sharma and
19
0: 2e6
O rlA = 2,7. lobiS to.YI I I i o irf= 5,0 -10 6b 6,0 10
. < Gr= = 8,0- lo Ws go -10103 2 4 6 10 2- 6 8 15 2-
IFh__38.251 Reynoldsahl Re_,; e1 r__e
Fig. 5 Average Nusselt number for sphere in
combined free and forced convective flow.
Sukhatme [29] have recently published experimental results concerning
the interaction between free and forced convection in flow over a hori-
zontal cylinder for Reynolds numbers from 10 to 5,000 and Grashof num-
103 2 610 2 6 8 1 2
bers from 3 x 103 to 7 x 10 no. These results indicate that the Reynolds
number exponent n in the parameter Gr/Re. is affected by turbulence and
separation phenomena and that a value of 3.25 is most suitable when free
convection dominates, whereas a value of 1.8 is more suitable at the
forced convection end. An average value of 2.5 was found to give a
reasonably good correlation in the transition region.
bers fBorner's correlation does not give insight into local variations
of the heat transfer coefficient, but it is convenient. By computing
Repar and Re,* phenoimultaneously and continuously from the time of launch
until the balloon has reached the float altitude, a smooth transition
between the forced and free convection regions can be made and the
influence of radiation can be superimposed directly.
20
In general, only the equilibrium temperature at float altitude is
important to the thermal design of balloon instrument packages. During
ascent forced convective heat transfer is quite effective [30] in main-
taining a small instrument package at a temperature close to that of
the ambient air, but when the balloon has reached its float altitude
only free convection can transfer heat directly between the package and
the surrounding air. The relative magnitude of the radiation to and
from the surfaces of the package dominates the thermal transfer during
the day, but convection enters prominently at night.
In certain specialized instrument packages, in addition to the
averaged heat transfer coefficient, local values at the top and bottom
surfaces are also sometimes of interest. The numerical study of Suriano
and Yang [31] provides some insight into the flow and temperature field
in the vicinity of a heated horizontal square plate at small Rayleigh
numbers. Table 2 shows averaged Nusselt numbers obtained by their cal-
culations for both the top and bottom surfaces. The temperature field
over a horizontal plate at a Rayleigh number of 50 (Fig. 6) suggests
boundary layer behavior on the lower surface but not on the upper. How-
ever, the analysis of Stewartson [32], as modified by Gill et al. [33],
indicates that a boundary layer also forms over the upper surface of a
heated horizontal strip and that the average Nusselt number for a strip
of width L in air can be predicted from the relation
h L-- c Gl5Nu = k =0.79 GrL (23)k L
a
in the laminar flow region. This result is not in complete agreement
with experimental data for the upper surface of a heated square plate
of side L in air [34]. These data give larger heat transfer coeffi-
cients that are correlated empirically by the relations
Nu = 0.50 GrL4 (105 < GrL < 2 x 107, laminar) (24)
Nu = 0.125 Grl/3 (2 x 107 < GrL < 3 x 109, turbulent) (25)L L
21
Table 2
AVERAGE NUSSELT NUMBERS FOR A HORIZONTAL PLATE IN FREE CONVECTION
NRa Nr = 0.72 Buznik andPr. .__ .. .. Bezlomtsev
x = 0- x = 0+ Average
0 1.049 1.047 1.048 1.00
0.10 1.052 1.045 1.048 1.28
5.0 1.201 0.946 1.074 1.77
10.0 1.406 0.932 1.169 1.91
50.0 2.879 1.259 2.069 2.38
100.0 4.041 1.330 2.685 2.64
200.0 6.166 1.492 3.829 2.96
250.0 7.194 1.594 4.394 3.00
300.0 7.620 1.678 4.469 3.03
1Buznik, V. M., and K. A. Bezlomtsev, 1960: A generalized equationfor the heat exchange of natural and forced convection during externalflow about bodies. Izv. Uyssh. Ucheb. Zaved. 2, 68-74; 1961: Ref. Zh.MeckZ. 6, Rev. 6V506.
\ =NRo50N p= 0.72
.6 \0.5 \0.4
0.50.7
0.8
0.9
0 .0
-0.5
0 0.50 1.0y
Fig. 6 Temperature field about a heated horizontalflat plate at a Rayleigh number of 50.
22
Heat transfer by free convection from the lower surface of finite
heated plates (or to the upper surface of cooled plates) has recently
been studied by Singh et al. [35,36] for square and circular plates and
a long strip. Local heat transfer coefficients are lowest in the center
and increase toward the edges. For a square plate of side L the local
Nusselt number at a distance x from the center is
h(x)L 0 i/58jf, R2xa2 ] , 2 4 1/4
h(x)L - 0.58 Ra1/5 1 - L ]+ 0.271 1 - + ... (26)k = ' '
The average Nusselt number for square plates, as well as for circular
plates and long strips, is given by the relation
h LNu- = k = C GrL (27)
a
where constants C and n are given in Table 3
Table 3
CONSTANTS FOR THE FREE CONVECTION EQUATION (Eq. 27)
Reference ConstantsNumbers C n
Square Platel(L is length of side)
35 (analytical) 0.89 0.234 (experimental) 1.00 0.2
Circular Platel(L is the diameter)
35 (analytical) 0.79 0.236 (experimental) 1.0 0.2
Long Stripl(L is the width)
32 and 33 (analytical) 0.80 0.2
1Heated surface facing downward, influence of side walls neglected.
Flow-visualization experiments with a number of other shapes, with
heated surface facing upward, have been reported by Husar and Sparrow
[37], but information regarding the interaction between the boundary
layer flow over vertical surfaces and the flow developing over hori-
zontal surfaces (i.e., the top and bottom of boxes or vertical cylin-
ders) is still lacking.
23
IV. CONVECTION INSIDE THE BALLOON
(q in Eqs. 14 and 15)1
The convection process inside the balloon is important because it
determines the temperature, the pressure, and the volume of the lift
gas (usually helium). Little research has been done on convection in-
side a sphere [38,39] and none has been done on convection inside
cavities resembling the shapes of high altitude balloons.
The heat transfer process is free convection. Hellums and
Churchill showed as early as 1961 [40,41] that the partial differen-
tial equations for the conservation of mass, momentum, and energy can
be solved for laminar natural convection under many different condi-
tions, but so far no solution for the heat transfer inside a balloon
has been obtained. Investigations of natural convection in annuli [42]
suggest that several types of flow patterns will exist as the tempera-
ture difference between the surface and the gas varies during a 24-hr
period. It seems likely that in the daytime, when the balloon skin is
warmer than the gas inside, there would be upward flow near the balloon
skin and downward flow in the interior. The reverse would be expected
at night. But there could also be situations during the day when gas
ascends on the side heated by the sun and descends on the cooler side.
As a first approximation, one could use existing solutions for flow in
a rectangular cavity heated on two sides as long as the flow is laminar.
But the tremendous size of a balloon makes it very likely that the flow
will be turbulent, except for very small temperature differences.
A semiempirical analysis [43] suggests that for turbulent free con-
vection over a vertical plate the Nusselt number fits the relationship
h L- = 0.021 (GrL . Pr)2 5 (28)
17 Lg
at Grashof numbers of the order of 1012, but Clark [44] suggests using
a relationship of the type
Dh gP (f g(Tf -T PrD
gg= c g · Prg (29)
24
with the constants C and n selected from Table 4, and with all physical
properties of the gas evaluated at the skin temperature.
Table 4
FREE CONVECTION IN A SPHERE(Constant C and Exponent n for Eq. 29)
Gr · Pr C n Type of Flow
104-109 0.59 1/4 Laminar
9O19lO12 0.13 1/3 Turbulent
In the absence of more concrete information, Dingwell et al. [45] used
Eq. (29) for their balloon study, with C and n equal to 0.13 and 1/3,
respectively. Equation (29) can then be used to write the rate of heat
transfer from the skin to the gas in the form
q l c(Tf - T) dAi = h T D (Tf TA i
= 4.83 h V2/3 (T - ) (30)c g f g
= 0.628 V2/3 k (T - T ) gf2 - Prg g f 2 T g
g g
Experimental data supporting the form of Eq. (29) have recently
been reported by Ulrich et al. [46] for the transient condition encoun-
tered in filling a cylindrical tank with air at Grashof numbers between
108 and 1013. The length-to-diameter ratio of their tanks varied
between 0.5 and 2.0 so their results should indicate what might occur in-
side a sphere. The experiments showed that during the initial stages of
the process the heat transfer coefficients were significantly higher
than those predicted by turbulent free convection, but agreement with
the heat transfer rate predicted by Eq. (30) was achieved after a few
seconds. Available information on the transient free convection heat
transfer characteristics of vertical surfaces in the laminar region is
extensive and has been summarized by Gebhart et al. [47]; little infor-
mation is available for the turbulent flow region [46].
25
V. RADIATION HEAT TRANSFER
The radiation heat transfer to and from balloons strongly influences
their performance and determines their short-term stability. Balloon
skins absorb direct and reflected solar radiation and radiation emitted
by the earth and the atmosphere. Over 99% of the solar radiation is in
the wavelength range between 0.2 and 4.0 p, whereas the earth and atmo-
spheric radiation is in the infrared range between 6 and 100 p, with
about 70% below 20 p. Balloon skins are usually at temperatures of
about 20°F and thus emit infrared radiation. For approximate calcula-
tions the sun and earth can be considered to be blackbodies at 9,500 and
80°F, respectively. The direct radiation from the earth and the clouds
can be as high as 150 BTU/ft2 hr [3]. However, the direct solar radia-
tion is collimated and, therefore, the effective receiving area is the
projected area, which in the case of a 1 million ft3 balloon (equivalent
to a 124 ft diam sphere) would be about 12,100 ft2. Reflected solar
radiation, on the other hand, impinges on the lower half of the total
surface area of the balloon, which is about 24,000 ft2. Earth radiation
impinges on the total area of the balloon (about 48,000 ft2) during
ascent through the atmosphere but impinges only on the lower half of the
balloon surface after it has risen to an altitude of 70,000 ft, where
less than 5% of the total air mass remains above. Thus, the total
direct solar radiation is about 5.4 x 106 BTU/hr, and the reflected ra-
diation is about 3.6 x 106 BTU/hr. Infrared radiation from the earth
and the atmosphere can amount to as much as 7.2 x 106 BTU/hr, but at
float altitude will be of the order of 2 x 106 BTU/hr. The balloon
emits radiation at a rate of 4.8 x e x 106 BTU/hr, where the effective
emissivity ef may vary between 0.2 and 0.7 for different skin materials.
In comparison, convection contributes only about 2 x 105 BTU/hr to the
heat transfer over the exterior balloon surface, but it is the only heat
transfer mechanism in the interior because helium is transparent to
radiation.
Since the actual amount of radiation absorbed depends critically on
the radiation properties of the receiving and emitting surfaces, a
26
knowledge of these properties is very important to the designer. The
two most common materials for balloon skins are polyethylene and Mylar,
which have (according to available data [48]) an effective absorptance
to ultraviolet solar radiation of about 0.12 and 0.17, respectively. The
absorptance to infrared earth radiation, which is also approximately
the emittance of the skin, is 0.21 for polyethylene and 0.63 for scrim
Mylar (0.5 mil Mylar on dacron scrim). A Mylar balloon absorbs, there-
fore, a much smaller percentage of its total radiation load from the
sun than does a polyethylene balloon, and since it also emits more
radiation by virtue of its higher emittance, a Mylar balloon will be
cooler than a polyethylene balloon. At the same time, however, because
of its high emittance a change in environmental conditions (e.g.,
setting of the sun) will reduce the gas temperature in a Mylar balloon
more quickly than in a polyethylene balloon. A Mylar balloon, there-
fore, has less altitude stability than a polyethylene balloon.
In the evaluation of the radiant contribution to the total heat
load on balloons and their instrument packages, engineers are faced with
a lack of experimental data for the pertinent surface radiation charac-
teristics of balloon materials. To calculate accurately the percentage
of direct solar incident radiation absorbed by a surface, one must know
its monochromatic absorptance for radiation of wavelengths between 0.2
and 4.0 p at various angles of incident radiation [49]. The absorptance
of thin films has a strong angular variation; radiation perpendicular
to the surface passes through more readily than does radiation at a
grazing angle. This angle variation can become particularly important
in a balloon system where the radiation incidence angle is zero at sun-
rise, rises to a maximum at noon, and then decreases again to zero at
sunset. For passive temperature control, i.e., the use of surfaces with
very different solar absorptances and infrared emittances, the influence
of the average incident angle of radiation cannot be ignored.
The difficulty of determining radiation properties for balloon
skins is exacerbated by the transparency of these skins, and the trans-
mittance has to be considered [50]. As will be shown,- to calculate
27
accurately the radiation heat load on a balloon, one needs to know the
total hemispherical emittance of the skin at its temperature, the direc-
tional and the angular hemispherical absorptance in the solar spectrum
(since surfaces are irradiated directly and indirectly by the sun), the
directional reflectances of clouds and terrestrial surfaces in the
solar spectrum, and the hemispherical absorptance in the infrared (for
the surfaces exposed to the earth or clouds).
In 1969, Edwards [51] summarized our knowledge of the radiative
transfer characteristics of materials and surveyed techniques available
to measure surface properties [52]. It does not seem feasible to mea-
sure spectral-angular surface properties for all potentially useful
materials. The amount of data would be unmanageable, and the cost with
present equipment would be unreasonably high. It would, therefore, be
desirable to classify materials according to their physical surface
properties and to develop working relationships to estimate "effective"
angular properties from measurements of a few select properties. One
should also know the influence on the radiation surface properties of
launch procedures, aging, solar radiation, and atmospheric phenomena so
thermal predictions can be made not only for idealized laboratory
samples but also for actual operational systems.
The flight lifetime of a balloon depends critically on the relation-
ship between the amount of radiant energy absorbed during the day and
the amount of radiant energy lost at night. In the morning the balloon
is usually at the lowest float altitude because the gas is at its lowest
temperature. After sunrise the gas is warmed by transient free convec-
tion from the skin after the skin has been warmed by the absorption of
solar radiation. The part of the skin exposed to the sun transfers heat
by transmission and internal emission to the rest of the skin. As the
temperature of the gas increases, the buoyancy of the balloon also in-
creases and the system begins to rise. This rise will continue until
shortly after sunset, whereupon the net loss of energy exceeds the net
input of energy, and the balloon begins to sink. At present the total
balloon heat balance over a 24-hr period shows a small loss in internal
energy. One of the long-range objectives of balloon designers is a
28
system which will passively maintain its average float altitude, i.e.,
the altitude for which the net change in lift-gas energy over a 24-hr
period is zero.
Various schemes to achieve a zero net change have been tried without
success. But even if a "permanent balloon" is not possible, increased
balloon lifetime and altitude stability would materially contribute to
programs aimed at permitting long-term weather prediction and eventual
weather control.
At altitudes below 70,000 ft the radiation incident on a balloon is
subject to considerable variation, and quantitative estimates are uncer-
tain. The amounts of infrared radiation from below and above will differ
and will both depend on the weather and cloud cover. The incident solar
radiation will also depend on the altitude and the clouds. At altitudes
over 70,000 ft a balloon is above the weather and receives nearly all of
its infrared radiation from below. Under these conditions the infrared
radiation heat load can be estimated with considerably more confidence.
Fortunately, large balloons are generally launched in good weather so
that changes in cloud cover during ascent are minimized.
Although measurements of upward and downward radiation in the atmo-
sphere have been made for many years, accurate evaluation of rapid
changes in radiation flux are unreliable because it is not possible to
predict local weather changes in advance. One could, however, modify
the radiation heat flux calculations to include observed weather data,
such as the types of clouds and their altitudes. Calculations based on
recent observations made at ESSA by Kuhn [53] clearly correlate changes
in the radiation flux with cloud cover. Application of available
knowledge of atmospheric radiation to balloon performance will, however,
require the close cooperation of meteorologists, cloud physicists, and
ballooning engineers.
For small packages used on superpressure balloons at intermediate
altitudes, an engineering analysis of the thermal control problem and a
summary of the experience gained in several flights by NCAR have been
presented by Lichfield and Carlson [30]. The basic problems of
29
temperature control at float altitude are quite similar to those en-
countered in spacecraft. In space, where only radiation can transfer
heat, the equilibrium temperature T developed by an opaque body sub-
jected only to direct solar radiation at the rate G over a projecteds
surface area S normal to the sun, having an averaged directional ab-s
sorptance per unit projected area, a , and a surface area, S, with
an average hemispherical emittance in the infrared eH is
a GS S
T / s, avg s s(31)
\ H,i
Equation (31) shows that in this case the ratio of the absorptance in
the solar spectrum to the emittance in the infrared controls the equi-
librium temperature.
In the balloon packages the heat transfer problem is more compli-
cated because of the addition of reflected solar radiation, convection,
and the influence of the atmospheric radiation, all of which depend
strongly on the cloud cover and weather. In daytime flights, the tem-
perature can be controlled by proper treatment of the surface of the
package. The properties of a number of materials and surface coatings
for such use are presented in Refs. 54-57; Table 5 presents a typical
selection. Silver sulfide, which has an average infrared emittance of
only 0.03 and an average solar absorptance of 0.60, has been used suc-
cessfully in balloon packages for which a temperature between 44 and
60°F was desirable. A further increase in temperature during the day
was achieved by covering the package with a thin film of material such
as Mylar which is transparent to radiation only in the solar spectrum
between 0.2 and 3.0 D, but has a large reflectance for infrared radia-
tion. This method of trapping the radiation, using this so-called
greenhouse effect, should be used cautiously to avoid an excessive tem-
perature rise during the middle of the day.
For nighttime balloon flights, energy must be stored to maintain
the internal temperatue of the flight package. A simple reservoir is
water. When a pound of water freezes, 42 W-hr of energy are released.
In addition, 0.3 W-hr of energy are released for each pound of water
30
Table 5
RADIATION CHARACTERISTICS OF SURFACES
Material IR Solar RatioEmissivity Absorption
Silver (polished) 0.02 0.07 0.28
Platinum 0.05 0.10 0.50
Aluminum 0.08 0.15 0.53
Nickel 0.12 0.15 0.80
Stellite 0.18 0.30 0.60
Aluminum paint 0.55 0.55 1.00
White lead paint 0.95 0.25 3.80
Zinc oxide paint 0.95 0.30 3.20
Gray paint 0.95 0.75 1.26
Black paint 0.95 0.95 1.00
Lamp black 0.95 0.97 0.98
Silver sulfide 1 0.03 0.60 0.05
Nickel blackl' 2 0.10 0.90 0.11
Cupric oxide1' 2 0.15 0.90 0.16
1These are special surfaces where a metal is covered with a very thinlayer of absorbing material. The layer is so thin that it is a frac-tion of a wavelength thick in the infrared and is, therefore, almosttransparent to IR. The result is that the IR emissivity is nearlythat of the underlying metal. However, the thickness is large com-pared to the wavelength of the maximum solar spectrum so the absorp-tivity is large for solar radiation.
2H. Tabor 1961: Solar Energy.
31
cooled 1F°. Table 6 compares the energy storage capacity of water with
that of zinc-air and silver-zinc batteries. The batteries have greater
energy storage capacity than water, but zinc-air batteries require a
supply of oxygen at balloon float altitudes, and water is cheaper and
easier to handle.
Table 6
ENERGY STORAGE CAPABILITIES OF WATER AND BATTERIES
W-hr/lb W-hr/kg W-hr/in.3
Water (heat of fusion) 42 93 1.5
Water (per °C) 0.52 1.16 0.02
Zinc-air 80 176 5
Lead-acid 11 24.2 1.2
Nickel-cadmium 8 17.6 0.4
Silver-cadmium 35 77.0 3.5
Silver-zinc 55 121 4.5
For flights lasting several days, the package must be able to
absorb as much heat during the day as it loses during the night. With
suitable black paint daytime surface temperatures of 6 to 100F can be
attained, but since a typical nighttime surface temperature is -67°F,
it is necessary to achieve a daytime surface temperature of about 1300F
to maintain temperatue equilibrium in the water. This requires the use
of special coatings, such as silver sulfide, or the use of one or more
greenhouse covers. One can also use solar cells to generate energy
within the package during the day, but this adds weight and complicates
the system.
33
VI. EMITTED RADIATION
(q in Eq. 15)
The balloon fabric, polyethylene or Mylar, transfers heat to the
atmosphere by infrared radiation. A typical Mylar balloon fabric
(0.35 mil thick Mylar with dacron scrim, 4 x 6 strands per inch) has
at its operating temperature an average transmittance of about 0.55, an
average reflectance of about 0.20, and an average absorptance of 0.25.
A typical polyethylene film has an average transmittance of 0.75, an
average reflectance of only 0.05, and an average absorptance of 0.20.
However, the monochromatic properties of fabric materials vary consid-
erably. Mylar, for example, has radiation windows with transmittances
as high as 0.80 for wavelengths between 3 and 6 p and opaque ranges with
transmittances as low as 0.10 for wavelengths between 13 to 15 p [58].
To calculate the emitted radiation it is necessary to know the
spectrally averaged hemispherical emittance in the infrared region.
The evaluation of an average hemispherical emittance for a given wave-
length range or a given temperature offers no difficulties for an opaque
surface [51,55,59]. As shown in Fig. 7, however, a surface element
of a balloon skin dS radiates not only directly into space, but also
into the interior where radiation can pass through the fabric into
space, can be reflected from the interior surface of the balloon fabric,
or can be absorbed by the fabric. To calculate accurately the "effec-
tive emittance" of a balloon from data on the surface radiation proper-
ties of its fabric skin, bidirectional values of the monochromatic
emittance, absorptivity, and reflectivity of the interior surface would
have to be known for the infrared wavelengths between 6 and 100 p [51].
Such measurements are difficult and are generally too expensive. For
balloon design it would actually be much more desirable to measure the
actual emittance of a spherical sample of the fabric material filled
with helium. However, no such data have as yet been taken, and calcula-
tions have been based on a model proposed by Germeles [8]. This model
assumes that the inner fabric surface obeys Lambert's law, i.e., it
emits and reflects diffusely. It also assumes that average values can
T-A^:-ei---r"7ei - 4T 4 xdS
<iei~zot 4 adSTi er 2 o- T 4 dS. -S '
ri e; T 4 dS ri ei oc T 4 d S
Ef=f f| e i (X) - T 4 dSdX ei rD2 Tf 4so
Q total e i w Dg 0 T 4 [I+-(+ +rI2.]Fig. 7 Emission of radiation from a balloon skin-the effective emittance.
Fig. 7 Emission of radiation from a balloon skin--the effective emittance.
35
replace the spectrum of values for the emittance, absorptivity, and
reflectivity of the inner surface over the wavelength range (between
6 and 20 p) for which data are available [53]. The net rate of emis-
sion from the entire balloon is then equal to the radiation directly
emitted from the outer surface, ei ~' D2 a T, plus that portion of the
radiation emitted by the interior surface which eventually passes
through the fabric, ei Ti T D2 a T4 (1 + ri. + .) + ) By summing
the series, one obtains the effective emissivity of the fabric
e =ff ei 1 + i (1 + ri + r . )eff i r1 i (lri .i ''
(32)
= -1 - l--i
where
100 /100
a = a(X) I (X) d / I (X) dX (33a)
p100 / .100
= r(X) I (X) dX I (X) dX (33b)
6
T = - r. - a. (33c)i 1 1
ei (Tf) = ai (Tf) (33d)
Use of the effective emissivity gives the rate of heat transfer from
the balloon fabric in the form
q = 4.83 eeff V213 oT4 (34)
where T4 is the average of the fourth power of the absolute temperature
of the balloon fabric.
36
The infrared hemispherical emittance of the surface of an opaque
body can be measured easily, so the determination of radiation emitted
by the surface of a balloon instrument package generally offers no
problem.
37
VII. DIRECT SOLAR RADIATION
(q in Eq. 15)2,d
The solar radiation spectrum has been investigated in great detail,
and summaries of the current state of knowledge are presented in Refs. 9
and 54. Figure 8 shows the solar spectrum at the outer fringes of the
atmosphere and at the surface of the earth after attenuation and absorp-
tion by the atmosphere. Over 99% of the solar energy is contained
within a narrow wavelength band between 0.2 and 4 p, and for most engi-
neering heat transfer calculations the sun's spectrum can be approxi-
mated by that of a blackbody at 9,500°F. The solar constant, i.e., the
radiation received by a surface placed perpendicular to the rays of the
sun outside the earth's atmosphere, is 2.0 cal/cm2 min, or 442 BTU/ft2 hr.
The solar radiation per unit area on a horizontal surface outside the
earth's atmosphere depends only on the zenith angle, i.e., the angle be-
tween a line normal to the surface and the rays of the sun. This angle
can be determined from the relationship
cos C = sin X sin a + cos X cos a cos h (35)S S
As shown in detail in Refs. 59 and 60, the radiation per unit area
on a surface tilted at an angle T to the horizontal is
G = G cos C cos ( (36)s
where
cos < = cos (A - a) cos (90 - %) sin T + sin (90 - C) cos T
T = the angle between the surface and the horizontal
a= the westward declination (measured from the southmeridian) of the projection on the earth's surfaceof the normal to the surface
X = latitude
a = solar declinations
h = local hour angle
A = azimuth of the sun, measured westward from the southmeridian
G = average incident solar radiations
0Q25aj , | I, g l | I | l | l | I | I' I I I ' I I I i I J I
0.20
'I t\ Solar Radiation Curve Outside Atmosphereo. ,s I ' o Solar Radiation Curve at Sea Level
0< . / \.-Curve for Blackbody at 59000 K"E
\ H20I o2 , H20
1010 IQ
I H,2'H20
H20
- / *n ©H0.05 - HO
::::· / / f j o ^,_ co°I H209 CoII IliiH201 C0
/3 I ;· HO CO2
0 02 0.4 Q6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2
WAVELENGTH (^)
Fig. 8 Spectral distribution of solar radiation in space and at sea level.
39
Once the angle between the sun and the surface, i.e., (% - T), is
known the solar radiation absorbed by a surface outside the atmosphere
is simply a (% - T)G , where a (% - T) is the effective directional
absorptance for that angle.
In passing through the atmosphere, the intensity and spectrum of
the solar energy are altered by absorption and scattering [61]. There-
fore, the radiation on an object is strongly dependent on the atmo-
spheric path length of the solar rays, usually expressed in terms of
the "optical air mass." Exact calculations of the attenuated spectrum
are quite cumbersome [61,62] and for engineering purposes such
calculations are only useful when the directional absorptances of the
receiving surfaces are known [63,64]. Figure 9 shows the distribution
of direct solar radiation incident at sea level on a horizontal surface,
as a function of wavelength, for several short paths corresponding to
optical air masses between 1.0 and 8.0. The optical air mass is unity
WAVELENGTH (L)0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 2.0 o
7^~~~0 ~~ _ E
.5 60 aEE | TOTAL ENERGY ' :
Air Mass W/cm2
cal/min cmr2
/
0 50 -- 1.0 0.0865 1.24 /> 1.5 0.0750 .080 2.0 0.0640 0.917
4.0 0.0372 0533 c1 40_ 6.0 0.0240 0.344 /
E 8.0 0.0152 0.218 ~~~~~~~~~~~~~~~~~~~~~-O 0.5 E
0.o
dettealeelfoar20masses1.0 0
Z WW 1.0 Z
06.0
35,000 30,000 25,000 20,000 15,000 10,000 5000 0nO
WAVE NUMBER (cm - ')
Fig. 9 Spectral distribution of solar radiation inci-dent at sea level for air masses 1.0 to 8.0.
40
when the sun is directly overhead and the body receiving radiation is
on the earth's surface. Under these conditions only 70.2% of the solar
constant is received. For other values of optical air mass (m), the
fraction of solar radiation received is expressed to within 3% accuracy
[8] by the empirical relation
sZ 0.5 (e-065m + e-0095m (37)
s,o
where optical air mass depends on the altitude and the sun's zenith
angle C. The variation of the optical air mass at sea level with zenith
angle, m(o,C), is given in Table 16-18 of Ref. 9 and can be closely
approximated [8] by the relationship
m(o,C) = [1229 + (614 cos %)2]½ - 614 cos C (38)
for 0 < C < 90°. Since the attenuation is proportional to the number
of air molecules in the path, for a given zenith angle the optical air
mass at altitude z can be related approximately to the air mass at sea
level by the relationship
m(z) = m(o) [p(z)z/p(o)] (39)
Using Eqs. (35) - (39) one can determine radiation on a surface at
any altitude, geographical location, and time between sunset and sunrise.
There are two short periods
90° < C < 90° + cos- kDearth + 2~ = \ Dea h+ 2z
before sea-level sunrise and, after sea-level sunset during which a bal-
loon also receives solar radiation. A method for determining the air
mass during these periods is presented in Ref. 8, but for most purposes
it is sufficiently accurate to double the value of the air mass calcu-
lated at sea-level sunrise or sunset.
41
The portion of the solar radiation absorbed at the surface of an
opaque body, such as an instrument package, can be calculated once the
orientation of the surface relative to the sun is known. The amount of
incident radiation absorbed per unit area is
r 4qabsorbed = a( - T, X) G (X,z)dX = a ( - T) G(z) (40)
0.2
However, as mentioned previously, the problem is more complicated for
the balloon because the skin is transparent, and a portion of the inci-
dent solar radiation is absorbed, a portion reflected, and the rest
transmitted into the interior where some of the radiation transmitted
on the first pass will be absorbed as a result of internal reflection
and absorption.
Except for occasional measurements in connection with basic inves-
tigation of radiation [51,63], only Dingwell [48] has attempted to
make systematic measurements of the radiation properties of balloon fab-
rics. Since balloon skins are transparent, absorptances are difficult
to measure directly. Therefore, Dingwell measured the monochromatic
transmittance of solar radiation using a Beckman D.K. spectrophotometer.
The reflectance was then estimated by observing interference fringes
caused by internal reflections and applying Fresnel's formula for nor-
mal incidence. Finally the monochromatic absorptance for incident ra-
diation, presumably normal to the surface, was calculated from the
relationship
a(X) = 1 - r(X) - T(X) (41)
and the integrated normal absorptance of the fabric over the solar spec-
trum was determined by numerical integration of the relationship
r4.0 / 4.0
a (normal) = | a(X) I (X) dX I (X) dX (42)
0.2 0.2
42
No measurements have yet been made of the effect on the radiation prop-
erties of balloon films of the solar radiation angle of incidence.
Edwards [64] has shown, however, that predicted equilibrium temperatures
can be as much as 40°F in error if the angular dependence of radiation
characteristics is neglected, and it would be desirable to measure the
directional absorptance, a(90,,X,T), for some typical materials.
To estimate from available information the percentage of the solar
radiation actually absorbed by the skin of a balloon, it will be assumed
that the absorptance of the skin is independent of the angle of inci-
dence and that radiation transmitted through the skin emerges diffusely
from the interior surface. Furthermore, the shape of the balloon will
be idealized as a sphere so that the projected area is D/D24. The
fraction of the incident solar energy absorbed on the first pass is
a G(z)D 2/4, and the fraction transmitted is T G(z)D2/4. Of the frac-s g_ _ s _tion transmitted, a will be absorbed by the fabric and r will again
5 s
be reflected. The total amount of the incident solar radiation even-
tually absorbed, obtained by summing this series of interreflections,
will be
qd = G(z) D2/4 a + s (43)\ r
or in terms of the gas volume in the balloon
q = G(z) 1.21 V23 a 1 + s (44)2,d g ls \ 1 - r
s
The zenith angle r can be defined in a time coordinate system re-
lated to the flight of the balloon. If the Greenwich hour angle at the
time of launch is GHA, then at any subsequent time t the hour angle is
6h = GHA - LONG + (t/240) (45)
where GHA and the longitude LONG are in degrees and t is in seconds,
43
VIII. REFLECTED SOLAR RADIATION
(q in Eq. 15)2 ,r
Until recently, the heat load of greatest uncertainty in Eq. (15)
was the reflected solar radiation. It was known from an overall heat
balance that the portion of the solar radiation reflected by the earth
and its atmosphere (the albedo), when averaged over time and space, was
about 34% [65]. It was also known from balloon and aircraft observa-
tions that the albedo can vary widely, but no accurate long-term mea-
surements could be made without an observation station outside the
atmosphere. The early measurements of Explorer VII and several Tiros
satellites resulted in data for only part of the globe because these
satellites were not in polar orbits. In 1967 and 1968, however, the
meteorological satellite Nimbus II measured the incoming and outgoing
radiation over the entire globe for several weeks, and Raschke of the
Goddard Space Flight Center correlated the results and presented them
in convenient graphs [65].1 These results are very useful for estimates
of the reflected solar radiation above the atmosphere at the geographic
locations scanned by Nimbus II, but they cover only a limited period and
do not indicate variations with weather or direction.
The works of Houghton [66] and Fritz [67] are, therefore, still
very useful for engineering design. Houghton established a convenient
graph for the approximate albedo as a function of latitude for clear,
partially overcast, and completely overcast skies (Fig. 10). Although
these curves were designed for conditions above the atmosphere, they
also will give approximate results for balloons in the atmosphere as
long as the sky above is not completely overcast. The accuracy of the
method, which is very good for altitudes above 50,000 ft, depends upon
the altitude and the amount of cloud cover. From the work of Fritz [67]
and Coulson [68] an estimate of the spectrum of the reflected solar radi-
ation can be made. Table 7 presents the results [54] as the ratio of the
solar radiation received from below at a wavelength X to the radiation
at the wavelength of maximum intensity for three sky conditions. The
1According to a private communication all the curves are shifted by 2.5°
due to a drafting error.
44
Table 7
RELATIVE SPECTRAL DISTRIBUTION OF SOLAR RADIATIONUNDER VARIOUS SKY CONDITIONS
R (1) R ( 1)__________ R R()
X Clear Mean Overcast X Clear Mean Overcast(p) skies skies (p) skies skies
0.29 0 0 0 0.53 0.378 0.668 0.807
0.30 0.882 0.721 0.477 0.54 0.252 0.663 0.812
0.31 0.892 0.761 0.534 0.55 0.333 0.637 0.795
0.32 0.848 0.749 0.553 0.56 0.312 0.615 0.770
0.33 1.000 0.920 0.705 0.57 0.288 0.590 0.752
0.34 0.858 0.813 0.648 0.58 0.276 0.581 0.748
0.35 0.815 0.802 0.661 0.59 0.262 0.563 0.734
0.36 0.744 0.746 0.634 0.60 0.241 0.541 0.717
0.37 0.768 0.796 0.700 0.70 0.134 0.396 0.554
0.38 0.671 0.714 0.632 0.80 0.084 0.293 0.425
0.39 0.575 0.624 0.570 0.90 0.057 0.224 0.331
0.40 0.758 0.840 0.772 1.00 0.042 0.179 0.266
0.41 0.781 1.000 0.950 1.10 0.028 0.149 0.219
0.42 0.790 0.937 0.925 1.20 0.019 0.118 0.181
0.43 0.675 0.835 0.835 1.30 0.017 0.095 0.145
0.44 0.708 0.908 0.934 1.40 0.015 0.076 0.115
0.45 0.734 0.958 1.000 1.50 0.013 0.063 0.093
0.46 0.649 0.892 0.960 1.60 0.010 0.051 0.078
0.47 0.713 0.864 0.954 1.70 0.008 0.042 0.063
0.48 0.563 0.834 0.935 1.80 0.006 0.034 0.052
0.49 0.487 0.749 0.853 1.90 0.005 0.029 0.045
0.50 0.524 0.727 0.840 2.00 0.005 0.025 0.037
0.51 0.422 0.697 0.825 4.00 0.000 0.002 0.028
0.52 0.378 0.650 0.780
R = the ratio of the solar radiation at wavelength X to thesolar radiation at the wavelength of maximum intensity.
45
1001 0 0 -\-.-I . I I .I I .- I _\I -- I -'
80
o 60 II OVERCAST SKIES
0
o 40 III MEAN2 0 ~ I CLEAR SKIES
0 10 20 30 40 50 60 70 80 90
LATITUDE (°)
Fig. 10 Albedo as a function of latitudeunder various sky conditions.
reflected solar radiation incident on a satellite or a balloon from a
surface element of the earth-atmosphere dS ise
dG = (r D/4) Glar rs(0) cos 0 cos C dS/12b (46)
where
dGs = reflected solar radiation incident on dSe
r (0,%) = the bidirectional reflectance of dSe for a zenith
angle C in the direction of the balloon, e
1 = the distance between the balloon and dSs-b e
For a known geographical distribution of r (09,), the reflected radia-
tion can be calculated numerically. If one assumes that the earth-
atmosphere system reflects uniformly and diffusely, Eq. (46) can be
approximately integrated [69] over the portion of the earth visible
46
from the balloon, and the radiation heat load resulting from albedo
reflection q becomes2 r
q (7 D/4) as solar [2 ra (- z/ cos s] (47)2,r g s solar s,a s
where
Go = solar constant (442 BTU/ft2 hr)solar
a = average effective absorptance of the skin in the solar
spectrum
rS = average hemispherical albedo of the earth-atmosphere fors,aa given zenith angle
z = altitude of the balloon
D = earth diameter (7,920 mi)
s = angle between a vertical line through the balloon and
the earth's center and a line through the earth's center
and the sun
When the atmosphere below a balloon is partially covered by clouds,
the reflection from below will not be uniform. In such a situation one
can improve the accuracy of the calculations by dividing the visible
earth-atmosphere system into areas of uniform, but not equal, reflec-
tion. Assuming that each area reflects diffusely, one can approach
this problem by means of shape-factor algebra [59,69,70,71] just as in
calculations of radiation between two diffuse surfaces.
Although the atmospheric layers are curved, one can approximate
the atmosphere below the balloon by a flat surface without introducing
an appreciable error. The shape factor between a small sphere dA and1
47
a plane rectangle A when the sphere is located at one corner of a2
second rectangle having a common side with A (Fig. 11) is2
F = -tan1 x y (48)dA -A 4r l+x2 +y/
1 2 VI + x' + y"
where x = b/c and y = a/c.
The reflectance of various types of clouds can be estimated from
Table 8 in conjunction with the relationship [77]
/ -b t\r= r - e ) (49)
where
r = reflectance of cloud of thickness t
r = reflectance of cloud of infinite depth00
t = cloud thickness in meters
b = constant whose value depends on liquid water1
content or cloud type
An approximate method, sufficiently accurate for most purposes, is
to assume that: (a) the atmosphere ends at the intersection of a
straight line between the balloon and the horizon, and (b) the atmo-
spheric surface below the balloon is flat.
As x and y approach infinity, the shape factor for radiation be-
tween a sphere and an infinitely large plane approaches TrD /2, which is
larger by a factor of 1 - 4 z/Darth J than the correct value between
a small and a large sphere. At an altitude of 20 mi, the error would
be about 10%. A calculation taking the curvature into account is pre-
sented by Cunningham [72].
d A x x=b/c-TS- .(+.... y=a/c
C bb
C
A a 0.
I/ 9 0 0 o
I , /an' x yI -IdA1 -A2 4 tan T
g 1 S 2 + y 2
Fig. 11 Shape factor for a small sphere and rectangular area.
49
Table 8()
MEAN VALUES OF THICKNESS, REFLECTANCE, AND ABSORPTANCE
AS WELL AS CONSTANTS b AND b FOR VARIOUS CLOUD TYPES1 2
Mean Mean Mean
Reflectance Absorptance Thicknesst
b i b2
r() (2) a ( 3) (10 - 4/m) (x 10- 4/m)
Low cloud 0.60 0.07 450 21.9 4.5
Middle cloud 0.48 0.04 600 10.5 1.8
High cloud 0.21 0.01 1,700 1.2 0.15
Nimbostratus 0.70 0.10 4,000 4.2 0.78
Cumulonimbus 0.70 0.10 6,000 2.8 0.52
Stratus 0.69 0.06 100 155 16.8
(1)Adopted from Ref. 77
2 ) = r, (1 - e ;t) value of r corresponds to mean thicknesst co t
(3)a = a (1 - e ); value of a corresponds to mean thickness
Data from which the geographic distribution of reflected solar
radiation above the atmosphere can be calculated were gathered by the
Nimbus II meteorological satellite, which was launched 16 May 1966 and
remained in a polar, synchronous, circular orbit at a mean altitude of
707 mi until 28 July 1966. Its orbital period was 108.6 min, and during
its 13 daily orbits the entire globe could be observed day and night.
Reflected solar radiation in the wavelength range between 0.2 and 4 i
and the earth-emitted long-wave radiation between 5 and 30 p were mea-
sured with a radiometer. Details of the data reduction and instrumen-
tation are presented by Raschke [65]. In the following, only the
application of the averaged data to the evaluation of the reflected
solar radiation will be discussed.
50
Using the parameters defined in Fig. 12, the solar radiation
reflected from a surface element dS depends on the location of d e one Sthe globe, the time of year, the weather conditions (primarily the cloud
cover), and the zenith angle of the sun. The total hemispherical radi-
ation reflected from dS will bee
27 7/2
qreflected = I (I ,e) sin 0 cos 0 dedi (50)
O 0
where I is the intensity of the reflected solar radiation and 0 and i
are the zenith and azimuth angles of measurement, respectively. Since
the intensity of radiation reflected from the earth-atmosphere system
depends on 0, p, and C1 (the instantaneous zenith angle of the sun),
pl, the instantaneous bidirectional reflectance of the area element
dS at longitude X and latitude (, can be defined ase
i, (X,()co P (51)cos l I+
s
where I+ is the instantaneous direct intensity of the direct solar radi-s
ation incident on dSe
The hemispherical directional reflectance r(%) is the ratio of
the total reflected solar radiation (as would be received by a black
hemisphere placed over dS ) to the incoming solar radiation. It de-
pends only on the zenith angle C and the time of year. From airplane
and balloon measurements Raschke prepared diagrams relating the ratio
between the directional hemispherical reflectance (r) and the bi-
directional reflectance (p1 = p/7) at various azimuth angles within
relatively narrow ranges of the zenith angle. Figure 13 shows one of
these diagrams in which isolines of x = r/p are drawn as functions of e
and i for a range of solar zenith angles between 60 and 80°. With the
aid of these intermediate approximations, Raschke calculated the hemi-
spherical directional reflectance from the Nimbus II data and presented
his results as maps of the average albedo of the earth-atmosphere sys-
tem during a two-week period [65]. Figure 14 shows such a map for the
northern hemisphere during the period 16-28 July 1966. The albedo
ZENITH
\ I SATELLITE
~~~~~z----
OBSERVED AREA (X,4{)
Fig. 12 'Satellite- or balloon-to-earth geometric configuration.
52
I= 180°
= 135
O = 60 ° 0
x ( , ,'= CONST. )' ( ~' = CONST. ) j=o" = 9
p ( i9, ~, ~'= CONST. ) e 'O"~V P~ = 04
0.4-- = 45°
0.3
0= 300V3 = 690=0°
Fig. 13 Variation of directional solar reflectancewith zenith angle (60° < C < 80°)
53
.--t Nio t m,,t . ,* e*tW" , ,. S S" "I it - t"l· ~~~~ ~ ~~~~~-- i /ALBEDO 1%1 c.· 7-w:4N NORTHERN HEMISPHER ENIMBUS A 16-28 ALy 1966 . . .i / '
mm~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ .'./..'~ '.'\(,,
r ;~~~~~~~~~~~~, :'~/ 7' .' ._/7z ~ - ~. -~
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ,,
Fig. 14 Albedo map for the northern hemisphereuigt
.r · ~ ~ ~ ~ ~ ~ ~ ~ ·c~~
.. 1 :'~~~~4jl· p L/5-5
g ·-,~~~~~~~~~~~ I~~~
or\40~ ~~~~t40I
$Q$O r ··~4
r~~~~~~~~~~~~~~~~~~~~~~~~3
oar ~~~~~~~~~~~~~~, t: " ev " W W " "1 .
54
varies from 20 to 30% over coastal parts of the North American continent
to 60% over Greenland and the Sahara Desert.
In addition to the albedo maps, Raschke also presented a correla-
tion of available data showing the variation of the directional hemi-
spherical reflectance with zenith angle (Fig. 15) and the ratio between
the directional hemispherical reflectance and the bidirectional reflec-
tance at various azimuth angles for snow, stratocumulus clouds, and
cloudless ocean areas. With the aid of these diagrams one can make pre-
dictions of the reflection at altitudes above 50,000 ft. Such predic-
tions are quite accurate except when there are changes in cloud cover.
For engineering design it is usually satisfactory, however, to use
Eq. (47) in combination with the graph in Fig. 15 relating the average
hemispherical reflectance to the zenith angle, which can be calculated
(using Eq. 45) in a time-coordinate system related to a balloon flight.
3.00
2.8
2.6 0-0 FUNCTION USED IN THIS WORK
*-2.4 -* *TIROS E (0.2p-5.0p): AFTER ARKING, A., PRIVATE COMMUNICATION, 1967
A---A TIROS II (0.55p-0.75#): AFTER LEVINE, J. S., PRIVATE COMMUNICATION, 1967 I
2.2 [2.2 -- O TIROS I (0.55M-0.75p): REFERENCE 34 /
2.0 -
1.8 -.,--O .,,
1.4 s2--- -,--..
^-^ y \ I
1.4 - '-O;O•• c -
.8 I I I I i I I0 10 20 30 40 50 60 70 80 90
SOLAR ZENITH ANGLE C (°)
Fig. 15 Variation of directional hemisphericalreflectance with zenith angle.
55
IX. INFRARED RADIATION FROM THE EARTH AND THE ATMOSPHERE
(q in Eq. 15)3
The contribution to the total heat load on a balloon by the radia-
tion from the earth and the atmosphere is an important variable in the
energy balance formulated by Eq. (15). Unfortunately, the quantitative
prediction of this portion of the total heat load is subject to some
uncertainty because it depends on several factors difficult to specify.
The infrared radiation from the earth and the atmosphere varies as
the balloon ascends. Immediately after its launch, the balloon receives
radiation from the atmosphere over its entire surface, but as it ascends
the amount of air above the balloon continuously decreases. Eventually,
only the lower part of the balloon receives radiation from the atmo-
sphere. This infrared radiation is dependent on the altitude and cloud
cover, and since the cloud cover often changes rapidly, a balloon can
experience unexpected and unpredictable fluctuations in the radiation
from the earth-atmosphere. The situation improves considerably, how-
ever, as the balloon ascends; once it has risen above the clouds and the
weather to an altitude of about 60,000 ft, the contribution of radiation
from the earth and the atmosphere can be predicted with a considerable
degree of accuracy.
Radiation from the earth and the atmosphere is of considerable
interest to meteorologists. Comprehensive treatises on the radiation
characteristics of the atmosphere have been published during the past
decade by outstanding meteorologists such as Goody [73], Feigelson [62],
Budyko [74], and Kondratyev [75]. The radiation characteristics have
been investigated and reduced to convenient graphs and charts by
Simpson [76], Yamamoto [77], and Elsasser and Culbertson [78]. Using
Nimbus II data Raschke also prepared infrared radiation maps. Figure 16
shows the infrared radiation emitted by the earth and the atmosphere
into space over the northern hemisphere during the period 16-28 July 1966.
In connection with efforts to construct a general circulation
model of the atmosphere, several researchers including Houghton [66],
London [79], Manabe and Moller [80], and Davis [81] have studied
56
OUTGOING LONGWAVE RADIATION (cal cm mmin / ..
r~~~~76.. ~ ~ .' ', ,,IBM~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~.
NORTHERN HEMISPHERENIMBUSX116-28 JULY,1966 o~J4 j
/ Q 0.36 04
;' 0 310.482 .
/. ·. ~. ~ ~ 033 / / 4 042
03 33'1
_ ~~~~~,1~~~~~~~~~~~~~~~~. ;.M?~r0.3155-A'.: ..
0.33~~~~~~~~~~~~~~~~3
-' ' 033'~~~~~~~~' 0367 ~~~~~~ K033-. .4 I " ·: ...
sphere·during the period 16-28 July 1
-,'0.30,
i~~~~~~~~a -0.42~~~~~~~~~~~~~~~~~~~~~4
0.33 4rv
·,~~~~~~~~~~~~~~~~~:,
.36~~~~~~ ,'k
,0.42:0 0, it ': O36 x
I ~ ~ ~ ~ '''~~~~ ~ ~~~.I. '0.!2 ~.iIlrr~~~~~~~~~~~~~~~~~~~~~~'' ·
7-._ i. :~ ,~ . ,~0.33 ·/,,Y ,, -f)~~~~~~~~3
i .I~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cm f 1( -L-- \· 2~~~~~~a o" VV T
Fig. 16 Infraredradainmpfrtenrhreisphere dr i n the' p erio 162 ul96
57
theoretical aspects of atmospheric radiation, but most of them calcu-
lated the meridional distribution and seasonal variation of the radia-
tion balance and not its global distribution. From a practical point of
view, Simpson's simple model [76,82] is still very useful for estimating
radiation heat loads, although Budyko [74] presents more accurate heat
balance calculations at the earth's surface. Neither of them, however,
considers the radiation within the atmosphere. Recently, Katayama [83]
has made valuable calculations of the radiation budget of the troposphere
over the northern hemisphere, and Sasamori [84] has developed a method
for calculating the upward and downward radiation flux in a cloudless
atmosphere. Sasamori's calculations are based on empirical formulas for
the spectral variations of the absorptances of water vapor, carbon diox-
ide, and ozone (the constituents of the atmosphere with absorption bands
in the infrared range) and on the assumption that the surface of the
earth is perfectly black. A summary of his results is shown for various
latitudes in Fig. 17, in which the upward and downward radiation fluxes
are plotted as a function of altitude. The spectral characteristics of
the radiation are not shown but can be calculated from the empirical
relations in Ref. 84.
-25 LAYERS ( YMAMOTO CHART).o 6 LAYERS(EMPIRICAL FORMULA)
20 a, , 1 ,T1 - '0- 20
0-10 N 30-40'N 60-N70'N
15 *sb 9· \Pi 0 1
E E
to .4 o .1 . » . *! - 150o Io
Ft-F' FFF F
1;) 6 -FX \F W
F'-F4 5
200 400 600 00 200 400 600 20 400 600
FLUX (cal/cm 2 day)
Fig. 17 Upward and downward radiation flux as a function of altitude.
58
It should be noted that the atmosphere is almost transparent to
wavelengths between 8 and 12 p. Consequently, a balloon will receive
such radiation directly from the earth. At longer and shorter wave-
lengths the atmospheric water vapor and carbon dioxide have strong
absorption bands, and in those parts of the spectrum the infrared radia-
tion received by a balloon is emitted by the atmosphere, usually at a
temperature lower than that of the earth. Some balloon materials ex-
hibit considerable variations in the monochromatic absorptance in the
infrared, and to reliably estimate the infrared radiation absorbed by
the skin, integrations over the spectrum between 6 and 100 p, as shown
by Eq. (33), are necessary [59,85]. For these integrations, simplified
models of the variations in the monochromatic radiation of the atmo-
sphere, such as those given in Refs. 9 or 59, are quite satisfactory.
In view of these complicated conditions it is not surprising that
several approaches have been taken to calculate the radiation from the
earth and its atmosphere which is absorbed by a balloon. Lally [3],
dealing only with superpressure balloons, divided the incoming infrared
radiation into four parts: from below, from above, and from two sides,
each illuminating an area of ( D2/4). The radiation environment is\ 6 / /
then estimated using the following simplified assumptions:
1. Downward radiation.
a. If clouds above: downward flux equals blackbody radiationfrom a source at the temperature of the cloud base.
b. If clear above: balloon above 9 mi--3.2 BTU/ft 2hr;balloon between 6-9 mi--6.3 BTU/ft 2hr; balloon below6 mi--12.7 BTU/ft2hr.
2. Upward radiation.
a. If clouds below: upward flux equals blackbody radiationfrom a source at the temperature of the cloud tops.
b. If clear below: upward radiation will vary from 48 to144 BTU/ft2hr depending on altitude and air mass. Table 9provides estimates of upward flux for several altitudesand air masses.
Table 9
RADIATION ENVIRONMENT FOR SUPERPRESSURE BALLOONS1
Average nighttime clear sky Mylar balloon (a = 0.05)
balloon super temperatureAltitude Season Air
Temperature Mylar balloon Metallized top Temperature in- Maximum added Maximum daytime
(°C) (°C) balloon crease per W/m2 solar flux temperature in-
(°C) increment (W/m2 ) crease
(*C) (°C)
Temperate,winter -10 0 5 0.24 35 8
3 km Temperature,(700 mb) summer 5 - 3 2 0.21 35 8
Tropic 10 - 5 0 0.20 35 8
Temperate,winter -30 0 8 0.30 35 10
6 km Temperate,(500 mb) summer -15 - 5 5 0.27 35 9
Tropic - 5 -10 2 0.25 35 9
Temperate,winter -50 5 15 0.36 40 14
9 km Temperate,(300 mb) summer -35 - 5 7 0.34 40 13
Tropic -30 -10 2 0.34 40 13
Temperate,winter -55 10 20 0.36 45 16
12 km Temperate,(200 mb) summer -55 10 20 0.36 45 16
Tropic -50 5 15 0.36 45 17
Temperate,winter -60 5 0.42 45 19
16 km Temperate,(100 mb) summer -65 10 0.42 45 21
Tropic -80 15 0.47 45 21
Temperate,winter -55 - 5 0.45 45 20
24 km Temperate,
(30 mb) summer -55 - 5 0.45 45 20
Tropic -55 - 5 0.45 45 20
1Adopted from Ref. 3.
60
3. The radiation from the sides can be estimated as equal toblackbody radiation from a source at the temperature of the airat balloon altitude.
London [85] considered only the upward and downward fluxes. The
advantage of this approach is that theoretical analyses and measurements
of atmospheric radiation usually provide the upward and downward, but
not horizontal, radiation fluxes. An instrument which has been widely
used at ESSA to obtain measurements of the upward and downward atmo-
spheric radiation was developed by Suomi and Kuhn [86]. This instrument
(Fig. 18) is basically a double-faced, hemispherical bolometer with
broad-response, blackened sensing surfaces shielded from convection cur-
rents by thin membranes of polyethylene. The upward and downward radi-
ation flux can be calculated from the temperatures, measured with tiny
thermistors, of the sensor surfaces and the air. A flight test of this
instrument, also called an "economical net-radiometer," is reported in
Ref. 87. Data taken during several balloon flights have been published
[e.g., 88-91], but data from other flights are still being processed at
ESSA [53]. Whenever the spectra of the upward and downward infrared
radiation are known, the rate at which infrared radiation is transferred
to the balloon skin can be calculated from the relationship
100
q = (7 D2 2) a (X) Gu (X) + a (X) i, (X) d3 g eff i,up eff i,down
(52)
where aeff (X) is the effective monochromatic absorptance of the balloon
film, which can be approximated from Eq. (43) by
(a ) [1 +1 -a(X) - r(X) ]a (X) [1 + 1- r(X)
and where G. (X) is the upward monochromatic radiation as measured byi,up
a hemispherical flat surface radiometer, and G do(X) is the downwardimonochromatic radown
monochromatic radiation, measured likewise.
61
Thermal Isolation
0.00025in. Aluminum Stretched Black Coated 7 7/ _a .--_i
____ __ __ -i41CBI Bead Thermistor
4.75 9a -. 75 -- 7
0 0.0005 in, Polyethylene Film
Fig. 18 Suomi-Kuhn flat plate radiometer.
62
Unfortunately, only the total average radiation over all wavelengths
is usually measured. Typical data from meteorological measurements are
illustrated in the graphs of Figs. 19, 20, and 21. In all three figures
the air temperature and the total radiation on a horizontal surface from
above and below are plotted as a function of altitude. Also shown are
the net radiation flux (i.e., the difference between the radiation from
above and from below) and the atmospheric cooling rate--quantities which
are of meteorological interest only.
Figures 19 and 20 show the average radiation environment at Green
Bay, Wisconsin, during summer and winter, and Fig. 21 shows the radia-
tion environment of a desert island at 2°S. The downward radiation in-
creases markedly with decreasing altitude, whereas the upward radiation
decreases slowly with increase in altitude. In winter, when the atmo-
spheric temperature variation with altitude is less than in summer, the
changes in radiation are also smaller. Near the equator where variation
in the atmospheric temperature with altitude is even larger than at
Green Bay during the summer, the changes in the infrared radiation en-
vironment are also more pronounced. It should be noted that the infra-
red radiation graphs in Figs. 19, 20, and 21 represent averages of the
total hemispherical radiation over all wavelengths. When the spectrum
is not known, an average absorptance must be estimated to calculate the
rate of absorption of infrared radiation from Eq. (52). There will, of
course, always be variations with changes in weather conditions, and the
amount of radiation absorbed by a balloon skin or an instrument package
will depend not only on the spectrum of the incoming radiation but also
on the variation with wavelength, as yet not known, of the directional
hemispherical absorptance of the receiving surface.
A third method of estimating the infrared heat load has been pro-
posed by Germeles [8]. It uses the measurements obtained by a "black-
ball" radiometer (Fig. 22), an instrument widely used by meteorologists
to measure the radiation in the atmosphere. The instrument, developed
by Gergen [92], consists essentially of a small balsa dodecahedron
painted black and surrounded by a convection shield. A thermistor im-
bedded in the center is used to measure T , the "equilibrium radiation
TEMPERATURE (°C)-90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30
100,|^~ ,Xq ~~ 4 |LEGEND
~200 0t \~ v 7 ~ o °DOWNWARD FLUX
300 03 UPWARD FLUXX AIR TEMPERATURE
.5 400E
500\ \U)
u) 600iti
700
800
900
1000 I-0.I 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
RADIATION (ly/min)
Fig. 19 Radiation environment at Green Bay, Wisconsin, in the summer.
TEMPERATURE (°C)-90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30
00
100
~ .8 {¥~ [|~ ~LEGEND
~200~ ~~ t k i~ °0o DOWNWARD FLUX300 \ 0 UPWARD FLUX
^~_ i R N~~ Q |~ X AIR TEMPERATURExQ 400E
V)
500
39 600-
70 0 \ \
800 -
900- : -
1000-0o. 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
RADIATION (.y/min)
Fig. 20 Radiation environment at Green Bay, Wisconsin, in the winter.
TEMPERATURE (°C)-90 -80 -70 -60 -50 -40 -30 -20 -10 0 10 20 30
100
X1 00 "o ~ > ~ \q |~ :LEGEND200-
~ 2 0 0 0t~ ~:~ ^Y "~0 ° DOWNWARD FLUX
300- UPWARD FLUX] K -Ad : x AIR -TEMPERATURE
-- 400
500
O 600
(t 700 \
800
900
1000-0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
RADIATION (.y/min)
Fig. 21 Radiation environment at a desert island, 2°S.
66
Fig. 22 Gergen "T Black Ballo" radiometer.
67
temperature" of the device. From this measurement, the radiation is
then calculated from the relationship [92]
G. = a T4 (53)1 r
Measurements with this device are carried out during the night so
the detector is not affected by the sun. It is claimed that the temper-
ature recorded by the black ball is representative of the total radia-
tion field to which it is exposed. Black-ball equilibrium temperatures
have been recorded as a function of altitude at different geographic
locations, and it has been observed that large changes in the black-ball
temperature profile occur within days at the same location. The results
of these measurements support the following approximate, simple, general
rule. At ground level, the radiation temperature is usually less than
the air temperature, but the deviation is about 10°F. The equivalent
radiation temperature decreases almost linearly with altitude up to the
tropopause, where it becomes about 75% of its ground value. From there
to higher altitudes the radiation temperature remains approximately con-
stant, indicating that most of the radiation is received from below.
Germeles [8] used data obtained by means of a black-ball radiometer
to calculate the infrared radiation on a balloon. He assumed that the
black-ball temperature profile is known. Since the black ball has a
shape similar to that of a balloon, the radiation absorbed by the bal-
loon can be obtained from the relationship
= 4.83 a a V213 T4 (54)q3 ' aeff g r
It is apparent that the estimates of radiation emitted by the atmosphere
and the earth require considerable improvement and elaboration. It may
well be that such improvement has not been made because the properties
of balloon fabrics are not precisely known, so that even if the heat
load could be calculated with considerably higher accuracy, the uncer-
tainty in the absorption load would remain.
68
At this juncture I would recommend: (a) using black-ball radiometer
data, when available, or (b) calculating the heat load from above and be-
low, making use of measurements obtained with an instrument such as the
Suomi-Kuhn radiometer, and calculating the actual amount of radiation
with a simple model of the atmosphere such as that proposed by Simpson
[76], which considers only water and carbon dioxide absorption. This
approach, described in Ref. 58 for use in spacecraft design, is also
directly applicable to calculations on balloon and instrument packages.
For calculations of heat loads in areas where the Suomi-Kuhn instrument
has not been flown, I suggest use of the Nimbus II data, which are sim-
ilar to albedo data in that they include the total radiation flux emit-
ted by the earth's atmosphere. This approach, of course, will only be
useful for altitudes above 60,000 ft since satellite data are taken far
outside the atmosphere. An aid to further improvement of the calcula-
tion of the heat load would be to fly several balloons instrumented to
measure gas temperature, the radiation heat load, and air temperature
simultaneously. Although such measurements have not been made, they are
feasible with existing instrumentation.
69
X. BALLOON TRAJECTORY COMPUTER MODEL
DESCRIPTION AND VALIDATION
A FORTRAN code has been created which utilizes the analyses of
balloon dynamics and thermodynamics contained in the previous chapters
to predict the vertical motion of zero-pressure balloons. Such a model
has many uses, It can predict ascent rates, time to reach ceiling, and
ceiling altitude in advance of an actual flight. An optimal ballasting
or valving schedule can also readily be determined by preliminary model
runs. The program and its use are described in detail in the appendix
which follows.
With a model as complex as that required to predict balloon motion,
many parameters enter which could be specified in such a way that the
model predictions would represent any single flight to good accuracy.
If, however, such a model is to be valid for a variety of balloon types
and flight conditions, a more fundamental approach than a simple curve-
fitting exercise is needed. In order to calibrate the present computer
simulation, the following approach has been used. Four recent, accurate-
ly monitored flights, which include a twenty-fold range in balloon volume,
daytime and nighttime launches, both hydrogen and helium lift gas, and
Mylar and polyethylene fabric materials, have been selected for model
validation. Of the thirty-three parameters which must be specified to
permit a unique solution to the equations of motion and energy, all but
two were determined by independent means. The parameter list is detailed
in the appendix and includes:
balloon gas transport properties, molecular weight andspecific heat
balloon fabric radiation properties (IR and UV)
balloon system weight and balloon volume
launch-time parameters - time of launch, initial freelift, fabric and gas temperatures, locationand altitude of site
atmospheric properties - temperature profile andblack ball profile
70
In principle, all but eight of the thirty-three parameters can be
specified readily to good accuracy from handbooks, The American Ephemeris
and Nautical Almanac, sonde data, and measurements normally made at a
balloon launch site. The eight parameters which are more difficult to
evaluate are:
1) internal convection coefficient
2) external convection coefficient
3) & 4) fabric UV and IR absorptances
5) initial free lift
6) atmospheric "black ball" profile
7) & 8) initial fabric and gas temperature
The latter two parameters, 7) and 8), were evaluated by assuming that
initially the fabric and lift gas are at launch site ambient temperature.
To evaluate the black ball profile, the simple rule described on p. 67
was used. Such an approach was justified by a sensitivity analysis which
showed that infrared profiles are not one of the sensitive factors during
the ascent phase of a flight. At float altitudes, the black ball tem-
perature has always been measured as approximately constant, implying
that all the IR radiation sources lie below the balloon. Consequently,
the only important component of a black ball profile is its value at
tropopause and above, where the temperature is nearly uniform.
The multiple pass fabric radiation properties 3) and 4) were
evaluated by the method described in [48] where the authors measured
absorptances in the IR and UV bands for more than 50 samples of balloon
fabrics. Computation of effective balloon values from such samples
(vide pp. 33-35 above) does not require the spherical balloon assumption
and should be quite accurate. However, the lubricating powder normally
used on plastic balloons has an unknown effect on the IR and UV absorp-
tance values.
The initial free lift of a balloon is not measured directly, but is
determined by semi-empirical means at most balloon launch facilities. A
sensitivity analysis has shown that this is one of three parameters
which must be specified quite accurately if a computer model is to
71
replicate an actual flight, Although the accuracy of the method
presently used to determine initial free lift could easily be improved,
the free lift specified in the balloon data sheets was usually assumed
to be a non-adjustable parameter for this study within its normal limit
of accuracy (+ 1%).
The only two parameters which were considered to be adjustable
during the model calibration were the inner and outer convective heat
transfer coefficients. As noted earlier, no heat transfer measurements
have been made on balloon shaped bodies and the expressions proposed for
the convective heat transfer coefficients (Eqs. 18, 20, 28) were at the
outset recognized to be only approximate. As a result of the present
model calibration, it is suggested that for zero pressure balloons the
external coefficient be increased by 50% over that predicted by Eqs, 18
and 20 and the internal free convection coefficient be increased by a
factor of three over the value computed from Eq. 28. In a survey of
convection in enclosures such as spheres and rectangular boxes, Ostrach
[98] has also shown that free convection Nusselt numbers for these
geometries contain variations of the same order, of 300%.
The balloon drag coefficient was calculated throughout all phases
of the flight by assuming the balloon to be a sphere. The data in [97]
were curve-fitted in several ranges of Reynolds number and their use
gave good replication of measured flight trajectories.
The measured time-altitude history of the four flights used for
model validation are plotted in Figs. 23-26 along with the model pre-
dictions. The agreement is seen to be good for all of the flights
during the ascent as well as the float regimes. From flight to flight
no adjustments were required in any parametric representations of the
balloon dynamics and thermodynamics to achieve this agreement.
In addition to altitude correlations, it is possible to attempt to
correlate model predictions of balloon gas and fabric temperatures with
measured flight values. In order to determine flight values of Tf and
Tg, upon which the model computations are based, an unmanageably large
72
90000 -
8000070000 ~- /
70000 //
60000 /
50000
40000
F 30000H:2 200000
F --.J 10000 /
o I I -- I I , 1 - , I l . -
0 2000 4000 6000 8000 10000 12000
TIf E-SEC THERMISTOR FLIGHT
Fig. 23 Vertical trajectory of "Thermiscor" Flight.
October, 1964, 250,000 ft 3 polyethylene balloon,He lift gas. Solid line - model prediction;dashed line- data.
73
80000
60000
50000 -
40000
-'1'
30000 -
Cl)
LL.20000 -
- / / -JI
- 10000-
0 2000 4000 6000 8000 10000 12000
TIME-SEC STRATOSCOPE S4-2
Fig. 24 Vertical trajectory of Stratoscope S4-2 Flight.
July, 1965, 5.5 million ft 3 Mylar balloon, Helift gas. Solid line - model prediction; dashedline - data,
74
90000
80000 -,//
70000
60000
50000
40000
30000
y 20000
10000
00 2000 4000 6000 8000 10000 12000
TIME-SEC STARGAZER FLIGHT
Fig. 25 Vertical trajectory of Stargazer Flight.
December, 1962, 3.1 million ft 3 Mylar balloon,He lift gas. Solid line - model prediction;dashed line - data.
75
140000 -
120000 - /
100000
8 0 0 0 0 -/ /80000 -
60000 - /
I-
_ 20000
. _ /
0 1000 2000 3000 4000 5000 6000 7000 8000
T I ME-SEC HYDROGEN FL I TE 571 PT
Fig. 26 Vertical trajectory of Speclal Hydrogen Flight,
July, 1970, 4 .5 million ft 3 polyethylene balloon,H2 lift gas. Solid line -model prediction; dashedline - data.
76
grid of thermocouple o thermistors would be needed. In the tThermistor'
Flight two film nd two balloon gas temperatures were -measured, These
measurements show the same trends as the model, but numerical equivalence
was not achieved simply because such a small sampling of gas and fabric
temperatures does not permit an accurate computation of space-averaged
values of T and T.f g
Caution should be exercised in accepting the claims of some previous
investigators who have asserted that they were able to predict balloon
motion from a mathematical model. Germeles [8], for example, has made
such a claim, but close inspection of his model showed a 20-fold error
in balloon gas transport properties, an improper use of black ball tem-
perature data, and an assumption that the heat transfer mechanism at the
balloon outer surface was by mixed forced and free convection mode at
Eckert numbers (Gr/Re 2 ) where such mixed mode convection has never been
observed in nature or the laboratory. As noted above, the proper selec-
tion of the large number of parameters present in this model can give
the illusion of a successful model when, in fact, only a good curve fit
has been achieved without any fundamental representation of reality.
77
APPENDIX
A COMPUTER PROGRAM FOR PREDICTING THE VERTICAL MOTION OF
ZERO-PRESSURE BALLOONS
JAN KREIDER
I
79
INTRODUCTION
The analysis presented in the body of this report can be used to
predict the vertical motion of balloons by means of a computer. This
appendix gives a complete outline of the steps in the computer program
developed to solve the equations describing the balloon motion and to
determine parameters of interest in the design and performance analysis
of high altitude balloons. The program is similar in concept and exe-
cution to that presented in Ref. 8, but it has been updated to account
for recent developments in heat transfer and has been coded in FOR-
TRAN IV.
The fluid mechanical and thermodynamic model study in the body of
this report requires six nonlinear, ordinary differential equations
(Eqs. 5, 11, 12, 14, 15, and z = U) to describe the vertical motion of
zero-pressure high-altitude balloons. The six dependent variables
listed below are all functions of the independent variable, time t:
z(t) - altitude of balloon above sea level
T (t) - balloon gas temperatureg
Tf(t) - balloon skin fabric temperature
V (t) - volume of balloon gas
U(t) - balloon vertical velocity
m (t) - mass of balloon gasg
The following parameters must be independently specified to obtain
a unique solution of the six model equations:
1. Atmospheric properties: density (p ), pressure (P ), temper-a *a
ature (Ta), thermal conductivity (ka), viscosity (p ), Prandtl number
(Pr ), and molecular weight (M ), as functions of altitude z.a
2. Balloon gas properties: thermal conductivity (k ) and viscos-
ity (p ) as functions of balloon gas temperature (T ); also Prandtl
number (Pr ), molecular weight (Mg), and specific heat at constantgvolume (
volume (c ).v~g
80
3. Infrared radiation field: specified by "black ball" radiation
equilibrium temperature (T ) as a function of z according to Eq. (53).
Alternatively, the rigorous approach outlined in Sect. IX concerning the
evaluation of q can be used.
4. Balloon fabric properties: mass (mf), specific heat (Cf),
effective infrared emittance and absorptance (e ff i and aeff i ) , and
effective solar absorptance (aeff,s).
5. Payload: ballast mass (mB), fabric mass (mf), payload mass
(m ), and a ballasting schedule if any.
6. Valving schedule: pounds of lift lost as a function of time
because of valving.
7. Other parameters: drag coefficient (CD), apparent additional
mass coefficient (CM), maximum balloon volume (VBM), and correction fac-
tors for convective heat transfer equations (C4 and C6).
8. Launch information: latitude (X) and longitude ((), local hour
angle (h), and solar declination (a ).
9. Initial conditions: the initial values of the six dependent
variables specified at t = 0.
The program integrates the six differential equations numerically using
a fourth-order Runge-Kutta technique once the listed parameters are
specified. The symbols used in the program are shown in Table Al. The
Fortran listing of the program is also provided.
INPUT DATA
The input data contain all the parameters and initial values re-
quired for a unique solution of the equations along with certain other
information concerning output, the integration, and duration of flight.
The data are read in from cards of two types:
1. Control cards: for identifying the type of data, these have an
integer number from 0 to 14 in 12 format in the first two columns.
81
Table Al
LIST OF IMPORTANT FORTRAN SYMBOLS
NCARFORTRAN Report Description Units
ABIR a Effective infrared absorptance ofballoon fabric for multiple absorp-tion of infrared radiation (InputData)
ABUV a Effective ultraviolet absorptance ofeffs balloon fabric for multiple absorp-
tion of solar radiation (Input Data)
AIRM m(z) Optical air mass used to completeatmospheric transmittance to solarradiation
ALPHA -Balloon gas viscosity parameter lb /ft sec(Input Data)
B (dm /dt)g/g Instantaneous ballasting rate lb/sec( BB(I) + BO )
BO -Fixed ballasting rate (Input Data) lb/sec
BB(I) - Ballasting schedule, corresponding lb/secto TB(I) (Input Data)
BETA -Balloon gas viscosity parameter(Input Data)
Cl cf Specific heat of balloon fabric ft lb/lb °R(Input Data)
C4 -Correction constant for convectionfrom air to balloon fabric (Eqs. 18and 20) (Input Data)
C6 -Correction constant for free convec-tion from balloon gas to fabric(Eqs. 28, 29) (Input Data)
CB CM Apparent additional mass coefficientof balloon (Input Data)
CAIR k Thermal conductivity of air ft lb/ft sec°Ra
CCSI(I) - Array of solar radiation factors -Type 7 data (Input Data)
82
Table Al (cont.)
NCARFORTRAN Report Description Units
CD CD Drag coefficient of balloon
CG k Thermal conductivity of balloon gas ft lb/ft sec°Rg
CIR(I) - Array of infrared radiation factors -Type 13 data (Input Data)
CLATD cos X * Cosine of latitude x cosine ofcos a solar declination
s
CP Specific heat of balloon gas at ft lb/lb °Rconstant pressure (c + R/M) m(Input Data)
CV c Specific heat of balloon gas at ft lb/lb °R9 g ~ constant volume (Input Data)
DDRAG - 1.21p ACDIUU2V /3/2g ft lb/sec
DEC a Solar declination during flight - degassumed constant (Input Data)
DEH2 q3 Absorption of IR radiation by ft lb/secballoon fabric
DEH3 q5 Emission of IR radiation by balloon ft lb/secfabric
DEH4 q Heating of balloon fabric by air ft lb/secthrough convection
DEH6 q Heating of balloon gas by fabric ft lb/secthrough free convection
DEH7 q Absorption of solar radiation by ft lb/secballoon fabric
DEVE - Rate of energy loss when gas is ft lb/secvalved or exhausted
(c g + R/Mg) (T )v,g g gg
DEWA - Rate of work done by balloon gas in ft lb/secexpanding against the atmosphere
(Pavg)
83
Table Al (cont.)
NCARFORTRAN Report Description Units
DKE -Rate of change of kinetic energy of ft lb/secballoon system
(dz(mg + mf + mB + mp + CPaVg) dt /c
DPE -Rate of change of potential energy ft lb/secof balloon
(P V m - - mr) dzag g f -mp dt g/gc
DPLT - Plotting routine time interval - must secbe an integer multiple of H (InputData)
DPR -Printing time interval (Input Data) sec
E E Rate of volumetric gas flow due to ft /secexhausting
EAIRT(I) T Array of observed atmospheric air °Ftemperatures corresponding to timesETIME(I) (Input Data)
EALT(I) z Array of observed balloon altitudes ftcorresponding to times ETIME(I)(Input Data)
ECHK -ENET - EP Energy check ratioENET (Eq. A10)
EFILMT(I) Tf Array of observed balloon film tem- °Fperatures corresponding to timesETIME(I) (Input Data)
EGAST(I) T Array of observed balloon gas ten- °Fg peratures corresponding to times
ETIME(I) (Input Data)
EMIR eeff,i Effective infrared emissivity ofef1 balloon fabric for multiple emission
(Input Data)
84
Table Al (cont.)
NCARFORTRAN Report Description Units
ENET -Difference between internal energy ft lbof gas and fabric at time t and at
beginning of flight, t ER dt (Eq. Al)
0
EP -Same as ENET but computed by ft lbsummation
EP = (Z ERi ) * Hi i
ER - Rate of change of mechanical and ft lb/secthermal energy of balloon (Eq. Al)
(- DKE + DPE - DDRAG - DEWA + DEVE+ q2 + q3 + q4 - q5)
ETIME(I) -Array of time of observed flight secdata points (Input Data)
ET0T -Internal energy of balloon gas and ft lbfabric (c m T + cfmfTf)
v,g g g f f f
EVEL(I) -Array of observed balloon velocities ft/seccorresponding to times ETIME(I)(Input Data)
F(1) dz/dt Vertical velocity of balloon ft/sec
F(2) d2 z/dt2 Vertical acceleration of balloon ft/sec2
F(3) Tf Rate of change of fabric temperature °F/secf
F(4) T Rate of change of gas temperature °F/secg
F(5) m Rate of change of gas mass lb /secg m
F(6) V Rate of change of balloon volume ft3/secg
FL - Free lift (pV - m - m lb
- mp)g/g
FLO - Initial free lift (Input Data) lb
85
Table Al (cont.)
NCARFORTRAN Report Description Units
4 2FLUXIR aT Atmospheric radiation flux at ft lb/sec ft
r balloon surface - computed fromblack ball profile RTIR(I)
2FS0L G Solar constant outside the ft lb/ft2sec
~s atmosphere ( = 96)
G g Acceleration due to gravity ft/sec2
( = 32.17)
GAMMA -Balloon gas conductivity parameter ft lb/lb °R(Input Data)
GHA GHA Greenwich hour angle of the sun at degstart of flight - positive westfrom the prime meridian (Input Data)
GMTS -Greenwich Mean Time at start of secflight (Input Data)
H - Time interval for computer integra- section (Input Data)
NBI -Number of Type 9 TB/BB data cards
NCIR -Number of Type 13 data cards
NEX -Number of Type 12 data cards
NIR - Number of Type 11 data cards
NSI -Number of Type 7 data cards
NT -Number of Type 10 ZZ/TZ data cards
NVI -Number of Type 8 TV/VV data cards
NYC -Number of model points to be plottedby YPLOT
P P Atmospheric pressure lb/fta
PERB -Cumulative percent of ballastdropped
86
Table Al (cont.)
NCARFORTRAN Report Description Units
PERE -Cumulative percent of gas exhausted
PERV - Cumulative percent of gas valved
PHI V/3 One third power of balloon volume ftg D = 1.24), Ab = 1.21)2, S = 4.834)2
PRG Pr Prandtl number of balloon gasg (Input Data)
R R Molar universal gas constant ft lb/lb mole°R( = 1545)
RA Gas constant for air (R/XMA) ft lb/lb °Rm
REN Re Balloon Reynolds number basedon ascent (descent) rate andequivalent diameter of balloon gas(1.24 x PHI)
RG Gas constant for balloon gas (R/XMG) ft lb/lb °Rm
RHO Pa Local density of atmosphere lb /ft 3
RH00 Density of air at ZZ(1) (q.v.) lb /ft 3
level (Input Data)
RH0G p Density of balloon gas lb /ft 3
RH~G Pg m
RTIR(I) T Array of black ball equilibrium °Rradiation temperatures corres-ponding to ZIR(I) (Input Data)
RTZ(I) (pT) Array of products of air density and lb °R/ft 3
temperature computed from atmos-pheric data corresponding to ZZ(I)
SB0LZ Stefan-Boltzmann constant ft lb/ft2 ecR 4
( = 3.6995 x 10' 1 0
SLATD sin A * Product of sines of latitude andsin a solar declination
s
TA T Atmospheric air temperature °Ra
87
Table Al (cont.)
NCARFORTRAN Report Description Units
TB(I) Array of times for scheduled secballasting - measured from startof flight (Input Data)
TCSI(I) -Array of times for solar radiation secfactor CCSI(I) measured from startof flight (Input Data)
TEMP T Air temperature computed from RHOT °Ra
TFO - Initial temperature of balloon °Rfabric (Input Data)
TGO -Initial temperature of balloon °Rgas (Input Data)
TIR(I) - Array of times for infrared secirradiation factor CIR(I) measuredfrom start of flight (Input Data)
TITLE - Descriptive title of model run
TMASS (mf + m Total mass of balloon system lbf g m
+ mB + mp)
TRANS G /G Transmittance of atmosphere tos Z s, solar radiation
TV(I) - Array of specified time for scheduled secvalving VV(I) measured from start offlight (Input Data)
TZ(I) -Array of atmospheric temperatures °Rcorresponding to ZZ(I) measuredupward from mean sea level (InputData)
TZA(I) -Atmospheric temperature profile °R
TZB(I) interpolation variables
V - Instantaneous valving rate (lb lift lb/seclost per sec) (VO + W(I))
VO - Constant valving rate (Input Data) lb/sec
88
Table Al (cont.)
NCARFORTRAN Report Description Units
VALD -Cumulative mass of gas valved lbm
VBM -Design maximum balloon volume ft(Input Data)
VISA a Viscosity of air lb /ft sec-a m
VISG pg Viscosity of balloon gas lbm/ft sec
W(I) -Scheduled rate of gas valving lb/sec(lb lift lost per sec) (InputData)
WF mf Mass of balloon fabric (does not lbinclude fittings) (Input Data)
WGO -Initial mass of balloon gas lbm
WGR0SS (m + m Total mass of payload (includes lbP B fittings and tapes), fabric, and
+ mf) ballast
WPB -Total initial mass of payload and lbballast (Input Data)
X t Time measured from start of balloon secflight to be modeled - may differfrom time measured from start ofmodel run XO
XO Time during flight to be modeled secat which model run is initiated(Input Data)
XLAT X Latitude of launch site - positive degnorth of equator (Input Data)
XL0NG LONG Longitude of launch site - measured degwestward from prime meridian (InputData)
XLAH 6 Local hour angle of the sun deg(XLAH = GHA - XLONG + X/240,)
89
Table Al (cont.)
NCARFORTRAN Report Description Units
XMA M Molecular weight of aira
XMG M Molecular weight of balloon gasg (Input Data)
XT -Specified final flight termination sectime measured from start of flight,not from start of model run XO(Input Data)
Y(1) z Altitude of balloon above mean ftsea level
Y(2) U Vertical velocity of balloon ft/secsystem
Y(3) Tf Mean temperature of balloon fabric °R
Y(4) T Mean temperature of balloon gas °Rg
Y(5) m Mass of balloon gas lbg m
Y(6) V Volume of balloon ft3
Y20 - Initial balloon velocity at XO ft/sec(Input Data)
ZO - Initial balloon altitude above ftmean sea level at XO (Input Data)
ZIR(I) - Array of altitudes above mean ftsea level for black balltemperatures RTIR(I) (Input Data)
ZMIN - Lowest permissible altitude - ftusually corresponding to groundlevel above mean sea level
(ZMIN > ZZ(1) > 0)
(Input Data)
90
Table Al (cont.)
NCARFORTRAN Report Description Units
ZZ(I) - Array of atmospheric temperature ftprofile altitudes above meansea level corresponding to TZ(I)
ZZ(l) < ZMINZZ(1) .< ZO
(Input Data)
91
2. Data cards: these have the first two columns blank and then
input data in F10.4 or E10.0 format.
There are 12 data types (coded Types 3-14), each of which must be
preceded by a control card identifying it. A tabular representation of
a data deck is shown in Table A2. The order of the control cards is to
be noted. The control card with the number 1 initiates computation; it
is, therefore, placed after all the data. The control card with the num-
ber 2 initiates plotting and after plotting is completed, terminates the
program. It is, therefore, the last card in the deck as shown.
TYPE 3 DATA
These data include:
C1 - balloon fabric specific heat (cf) (ft lb/lbm°R)
C4 - convection heat transfer factorsC6 J
ABIR - effective infrared absorptance (a ff )eff,i
EMIR - effective infrared emittance (e ff i)
ABUV - effective solar absorptance (aeff,s)
TYPE 4 DATA
These data include:
WPB - payload mass at start of model run (mB + mp) (lb m )
WF - balloon fabric mass (mf) (lb m )
VBM - maximum balloon volume as specified by manufacturer (ft )
FLO - free lift at start of model run (lb)
CB - apparent additional mass coefficient for a sphere (CM)
ZMIN - lowest permissible altitude (ft) (ZMIN 2 ZZ(1) > 0)
TYPE 5 DATA
These data include:
TGO - gas temperature at start of model run (°R)
TFO - fabric temperature at start of model run (°R)
ZO - balloon altitude above MSL at start of model run (ft)
(ZO ' ZZ(1) > 0)
Y20 - balloon vertical speed at start of model run (ft/sec)
DEC - solar declination on launch day - positive N of equator
(Source: The Air Almanac) (deg)_.......... . -.. ..
92
XLAT - latitude of launch site - positive N of equator (deg)
XLONG - longitude of launch site - positive W of prime meridian(deg)
TYPE 6 DATA
These data include:
H - integration time interval (sec)
DPR - output printing interval (sec)
XO - model run start time measured from flight start time (sec)
XT - model run termination time measured from flight start
time (sec)
GMTS - Greenwich Mean Time at model run start time (sec)
GHA - Greenwich Hour Angle of the sun at flight start timemeasured positive W from the prime meridian (Source: TheAir Almanac) (deg)
DPLT - output plotting interval (sec). If zero, plots are notgenerated.
TYPE 7 DATA
These data include two arrays of time TCSI in seconds from the start
of flight and the "solar radiation factor" CCSI which accounts for
cloud cover, etc. They are in order of increasing TCSI and are
limited to 100 cards. If no cloud effects are considered, the
correct data are the two cards:
TCSI(1) = XO CCSI(1) = 1.0
TCSI(2) = XT CCSI(2) = 1.0
CCSI data are extrapolated if the balloon flies longer than
TCSI(NSI). NSI is the number of Type 7 data cards.
TYPE 8 DATA
These data include:
VO - The constant valving rate on the first card (lb lift lost
per sec). If no gas is valved uniformly, this card must
still lead Type 8 cards with a value 0.0.
TV and VV - Two arrays of time measured from start of flight (sec)
and valving rate (lb lift lost per sec) schedule. They are
in order of increasing TV and are limited to 100 cards.
TV(1) must be equal to XO, TV(NVI) must be equal to or
93
greater than XT. NVI is the number of Type 8 data
cards containing TV/VV data.
Example: XO = 0. , XT = 36,000.
VO = 1.0
TV(1) = 0. VW() = 0.
TV(2) = 18,000. VV(2) = 0.3
TV(3) = 18,100. VV(3) = 0.
TVC4) = 36,000. W(4) = 0.
These data mean that the constant valving rate is 1.0 lb/sec
and that scheduled valving takes place only from 18,000 to
18,100 sec at a rate of 0.3 lb/sec.
TYPE 9 DATA
These data include:
BO - The constant ballasting rate (lb/sec) on the first card.
If there is no uniform ballasting, this card must still be
present with a value of 0.0.
TB and BB - Two arrays of time (sec) measured from start of
flight and ballasting rate (lb/sec) schedule.
The rules for these data are similar to those for Type 8.
TYPE 10 DATA
These data include:
RH00 - Air density (lbm/ft 3 ) at ZZ(1) level on the first card
ZZ and TZ - Two arrays of altitude above mean sea level (ft)
and the corresponding air temperature (°R). They are in
order of increasing ZZ and are limited to 100 cards.
Properties of the first layer are extrapolated for properties below ZZ(1)
if necessary (as required for optical air mass computation, for example).
Note that ZZ(1) may be below ZMIN but may not be greater than ZMIN. ZZ(1)
may also differ from ZO but must not exceed it. Thus, ZZ(1) may be
chosen at a level more convenient for density specification than the
downstream ground level ZMIN or the initial altitude ZO. ZZ(NT) should
be equal to or greater than the expected maximum altitude of the balloon.
Atmospheric data for the model are extrapolated from the uppermost layer
whenever the balloon goes above ZZ(NT); NT is the number of Type 10 data
94
cards containing ZZ/TZ data.
TYPE 11 DATA
These data include two arrays of altitude above mean sea level
ZIR (ft) and the corresponding values of black ball radiation equilibrium
temperature TIR (°R). The rules for these data are the same as for Type
10 ZZ/TZ data. Whenever the balloon goes above ZIR(NIR), infrared data
from the uppermost data layer are extrapolated; NIR is the number of
Type 11 data cards.
TYPE 12 DATA
These data include six arrays of observed altitude EALT, gas tem-
perature EGAST, film temperature EFILMT, air temperature EAIRT, and
ascent rate EVEL corresponding to flight times ETIME from an actual
flight which the program is to model. These data may be used for flight
correlation checks. The data must be in order of increasing ETIME and
are limited to 400 cards.
TYPE 13 DATA
These data consist of two arrays of time TIR from the start of
flight and corresponding values of the "infrared radiation factor" CIR.
This factor accounts for possible transient cold cloud cover infrared
effects. The rules for these data are similar to those for Type 7 data.
TYPE 14 DATA
These data include the following information about the balloon gas:
PRG - balloon gas Prandtl number
ALPHA)
BETA 3- empirical constants for viscosity computation from an
expression of the form:
BETA= ALPHA * T BETA
g g
ALPHA has units (lbm/ft sec)m
GAMMA - constant for computing conductivity from viscosity
assuming constant Pr ;g
kg = GAMMA * ,g
GAMMA has units (ft lbf/lbm - OR)i m
95
XMG - balloon gas molecular weight
CP - specific heat of balloon gas at constant pressure
(ft - lbf/lbm 0R)
CV - specific heat of balloon gas at constant volume
(ft - lbf/lbm°R)
96
Table A2
CONTENT AND ORDER OF INPUT CARDS FOR ONE FLIGHT
Field Format
2 12 22 32 42 52 62 72
TITLE 8A10
3 I2
C1 C4 C6 ABIR EMIR ABUV F10.4
4 I2
WPB WF VBM FLO CB ZMIN F10.4
5 I2
TGO TFO ZO Y20 DEC XLAT XL0NG F10.4
6 I2
H DPR XO XT GMTS GHA DPLT F10.4
7 12
TCSI(1) CCSI(1) F10,4
*: F10.4
TCSI(NSI) CCSI NSI) F10.4
8 I2
VO F10.4
TV(1) VV(1) F10.4
*':~~~~ FlO.4;C, ~~F10.4
TV(NVI) VV(NVI) F10.4
~~~~~~~~~~~9 ~~~~1~~I2
BO F10.4
TB(1) BB(1) F10.4
' ' F10.4
TB(NBI) BB(NBI) F10.4
97
Table A2 (cont.)
Field Format
2 12 22 32 42 52 62 72
10 12
RHO F10.4
ZZ(1) TZ(1) F10.4
: F10.4
ZZ(NT) TZ(NT) F10.4
11 12
ZIR(1) RTIR(1) F10.4
F10.4
ZIR(NIR) RTIR(NIR) F10.4
12 12
ETIME(1) EALT(1) EAIRT(1) EFILMT(1) EGAST(1) EVEL(1) F10.4
......: :i~ :~ :~ :~ ~ F10.4
ETIME(NEX) EALT(NEX) EAIRT(NEX) EFILMT(NEX) EGAST(NEX) EVEL(NEX) F10.4
13 I2
TIR(1) CIR(1) F10.4
: ' F10.4
TIR(NCIR) CIR(NCIR) F10.4
14 I2
PRG ALPHA BETA GAMMA XMG CP CV 10.0
1 I2
2 I2
98
THE PROGRAM
The program is composed of a MAIN routine and six subroutines (RNGKTA,
YPRIME, RHOT, DRAGC, YPLOT, and TIME) which perform special tasks.
The MAIN Routine
This routine reads the input data from the input tape. When a run
is made with more than one flight, the computer will read the input data
and compute one flight at a time. The cards containing the input data
as well as the control cards must be punched correctly and must be in
the proper order as described in the INPUT DATA section. Otherwise,
the first time that the MAIN finds an error, it will terminate the
entire run after writing a comment in the output tape which will help
locate the error in the data.
As a further check on the input data, before proceeding to the com-
putation of the flight, the MAIN will write on the output tape all the
data used for the flight. The input data printed on the output should
be examined carefully to insure that they are identical to the input
data.
A flight will be terminated automatically when:
1. The entire payload, including the gondola, has been
dropped. This could be caused by excessive ballasting
(see below). A comment will be written on the output
tape indicating that this has happened.
2. The balloon hits the ground.
3. The flight time exceeds the flight time specified in the
input data.
The program will then proceed to the next flight.
The MAIN does a considerable amount of computation involved in
interpolating the input data and reducing it to a suitable form. It
also computes some of the variables in the desired output form and
stores them on the output tape.
99
The MAIN also exhausts gas artificially. The integration is
carried out in time intervals equal to H. At the end of each interval
the instantaneous volume Y(6) of the gas is compared with the inflated
volume of the balloon VBM as specified by its manufacturer. If Y(6) is
equal to or smaller than VBM, no gas is exhausted and the computer pro-
ceeds to the next step. If Y(6) is greater than VBM, the exhausting
rate is set equal to (VBM - Y(6))/H and the same step is repeated. If
Y(6) again comes out greater than VBM, the exhausting rate is increased
by (VBM - Y(6))/H, etc. Twenty such iterations per integrating step are
included in the basic program.
Finally, the MAIN does an energy check, which will be described
later.
Subroutine RNGKTA
The actual integration of the six differential equations is carried
out by this subroutine with Gill's fourth-order Runge-Kutta method,
which is a stable, self-starting, accurate numerical integration tech-
nique; RNGKTA requires another subroutine YPRIME in which the differen-
tial equations are stated and derivatives computed.
Subroutine YPRIME
This subroutine contains the six first-order differential equations
and evaluates the first derivatives of the dependent variables. It also
evaluates the various heat transfer rates. Thus, YPRIME is called fre-
quently by MAIN, as well as by RNGKTA, whenever information is needed
concerning the derivatives of the dependent variables or the heat trans-
fer rates.
To determine the rate of absorption of solar radiation, YPRIME
computes the intensity of solar radiation and, when sunrise or sunset
occurs at the balloon, it computes the Greenwich Mean Time (GMT) and
writes directly on the output tape the appropriate comment (for
instance, GMT - 2.20.13 SUNSET AT BALLOON),
100
When the balloon goes above the infrared radiation field specified
in the input data (Type 11), YPRIME will print on-line an appropriate
comment. The flight will be continued using the infrared data of the
highest altitude for as long as the balloon remains above the specified
infrared field.
In computing the convective heat transfer rates to the
atmosphere, YPRIME gets information about the atmosphere from subroutine
RHOT.
Subroutine RHOT
This subroutine computes the atmospheric temperature and the
product of atmospheric temperature and density for given altitude.
When the balloon goes above the atmospheric temperature profile speci-
fied in the input data (Type 10), RHOT will print on-line an appropri-
ate comment. The flight will be continued using the atmospheric data
of the highest altitude for as long as the balloon remains above the
specified atmosphere.
Subroutine RHOT is called frequently by MAIN and YPRIME to give
information about the atmosphere.
Subroutine DRAGC
This subroutine computes the drag coefficient for the balloon, the
shape of which is assumed to be spherical. For Reynolds numbers less
than 1.0, Stokes Law is used. For Reynolds numbers between 1.0 and
300,000, the data presented in Ref. 97 are used. Three equations are
required to fit the data, and the form of these equations depends on
which subinterval of the Reynolds number interval between 1.0 and
300,000 is of interest. For Reynolds numbers larger than 300,000 a
value of CD = 0.5 is used. Subroutine DRAGC is called by YPRIME each
time YPRIME is called.
101
Subroutine TIME
This subroutine is called by MAIN and YPRIME when the GMT is
required during the model run.
Subroutine YPLOT (written by J.H. Smalley)
This subroutine is called by MAIN after all calculations have been
completed for a given flight. YPLOT plots the following variables ver-
sus local time in hours:
Variable Symbol on Plot
Air temperature (°F) A
Balloon Fabric Temperature (°F) F
Balloon gas temperature (°F) G
Balloon altitude (ft) H
Balloon vertical velocity (ft/min) V
Percent free lift L
If two or more variables have the same ordinate value at any time, only
one symbol is printed. A maximum of 1,000 values of any of the six
variables listed above may be plotted. If DPLT = 0, no plot is generated.
ACCURACY OF INTEGRATION
With a program as massive as this it is desirable to have a scheme
by which the accuracy of integration can be estimated for a given
integrating-time interval. With such a scheme the integrating-time
interval can be maximized for a given desired accuracy and, thus, the
total computer time per flight can be minimized.
To this end, an energy check is most effective. If Eq. (5) is
multiplied by U and Eqs. (14) and (15) are added, after some rearrange-
ment, the following energy equation is obtained:
d (ETOT) = - DKE + DPE - DDRAG - DEWA + DEVE + q + q - q + q (Al)dt 3 4 5 .2
102
where
ETOT = cv m T + c mf T (A2)vg g g f f f
DKE = (m + mf + mB +m + CM p V ) U (A3)g f B p Ma g g
DPE = (p V -m - m -m - m) U (A4)ag g f p B
DDRAG = (1.21/2g ) p CD U | 2 V2/3 (A5)g
DEWA = p V (A6)a g
DEVE = c T m (A7)P g g
and where c is the specific heat at constant pressure of the gas.P
Note that Eq. (Al) relates the rates at which the various forms of
energy of the gas-fabric system are exchanged. The interpretations of
the various terms are: ETOT is the internal energy; DKE and DPE are
the rates of change of kinetic and potential energy, respectively;
DDRAG is the rate at which the energy is expended to overcome drag;
DEWA is the rate at which work is done (on the atmosphere) when the bal-
loon expands; and DEVE is the rate of energy lost when gas is valved or
exhausted. Finally, the sum of the q terms is the rate of net heat
transfer to the system.
Let the right hand side of Eq. (Al) be denoted by ER. Integrating
this equation from time zero to t, one obtains:
ENET = ETOT - ETOTI = ER dt (A8)Let
nEP = HZ ER. (A9)
i=l 1
where ER. is the value of ER at the end of each time step H.1
103
At the end of each integration by RNGKTA, the MAIN routine eval-
uates ETOT and, therefore, ENET from the integrated variables. Simi-
larly, it evaluates the increment in EP, which is H(ERi), resulting
from each step and keeps track of the total EP. Clearly, ENET and EP
thus evaluated are not equal for two reasons (if all integrations were
exact, ENET and EP would be identical). First, there is an error in-
volved in the integrations done by RNGKTA. Second, there is another
error involved in the above approximate first order integration of ER.
The second error is certainly larger than the first one. Nevertheless,
the ratio
ECHK ENET-EP (A10)ENET
which is evaluated by MAIN and stored on the output tape each time
output is stored there, has some bearing on the accuracy of RNGKTA.
If ECHK is a small number, this means, at least, that RNGKTA is very
accurate.
OUTPUTS
As stated above, the first part of output is a printout of the
input data used for the flight. The printout of input data is followed
by the computed output. A unit of output contains one line; the con-
tents of the line are the values of the variables appearing at the head
of each page of output. These variables are:
GMT - Greenwich Mean Time (hr, min, sec)
TIME - Time from beginning of flight (min)
ALTITUDE - Altitude of balloon from sea level (ft)
VEL - Velocity of balloon (ft/min)
PRESS - Atmospheric pressure (mb)
TA - Atmospheric temperature (°R)
TF - Balloon fabric temperature (°R)
104
TG - Balloon gas temperature (OR)
VOLUME - Balloon volume (ft3)
TMASS - Mass of payload ballast, gas and balloon fabric (lb)m
GMASS - Mass of balloon gas (lb)m
FR LIFT - Free lift (lb)
PERB - Cumulative ballast dropped (percent of initial load--
payload plus ballast)
PERV - Cumulative gas valved (percent of initial gas weight)
PERE - Cumulative gas exhausted (percent of initial gas weight)
IRS - Number of iterations required to exhaust an adequate
amount of gas during the most recent integrating step
ECHK - Energy check, as explained above
When sunset or sunrise occurs at the balloon, the GMT of the occur-
rence, together with the appropriate comment, are printed on the output.
When a flight is aborted because of errors in the data, the output
contains comments which will help locate the errors.
105
OTHER RULES FOR USAGE
In MAIN, a card reading "KIP = 0" is noted near the start of the
listing. The function of KIP is as follows:
KIP = 0: input data are printed
KIP = 1: input data are not printed.
To achieve greater accuracy during the initial stages of the flight,
a one second integration step is used instead of that specified by the
input value H.
Valving and ballasting events must span at least one integration
interval H. If not, the event will not be sensed by the model.
A model run may be begun at any point in an actual flight if the
investigator wishes to examine a specific portion of the flight in
detail. This is done by specifying the appropriate values of FLO, TGO,
TFO, ZO, Y20, XO, etc. in the input data which correspond to the time
at which the model run is to be initiated.
More than one flight may be computed in one computer run. This
is done by simply placing the decks of input cards in consecutive order
replacing those intermediate control data cards with a 2 in Column 2
by blank cards. If certain data is the same from one flight to the
next, it is carried over automatically from the first flight to subse-
quent flights. Each new data deck must be preceded by a TITLE card
(format 8A10).
A microfilm plotting routine has been developed for use with this
program on the NCAR computers; it is used to plot model prediction and
actual flight data for model validation purposes only and has not been
included in this report. A listing of subroutine MFP is available upon
request from the authors or from the NCAR Palestine Launch Site, Box 1175,
Palestine, Texas 75801.
106
In the data description section above a distinction is made between
"start of flight" and "start of model run" times. "Start of flight"
refers to the time at which the balloon launch took place. "Start of
model run" refers to the point at which the computer begins its compu-
tations; it may be at the start of the flight or at a later time at the
user s option.
Selection of the optimum integration interval H is facilitated by
the printout of ECHK. It has been found that a value of H resulting in
ECHK < .010 is satisfactory. A smaller integration interval will not
materially change the output values but will consume more computer time
unnecessarily.
107
PROGRAM MAINTDMENSION Y(16),F (6) ZZ(lOO) ,TZ( 100,RTZ(100) ,TZA( 100) TZO(100)
1TCSI (100) CCSI (100)TV (100) ,VV (100) ,TB (100) BB (10) ,XX (7) T I TLE(122) ,RT IR( 100) ,Z R( 1 0 ),DIRrZ ( 1 0) ,S IDT( 100) ET IME(400)FALT(400),TTR( InO)CTR(l00),r CIRnT(l00),YPH(OOO,1 ),XPT ( 1O),4YPT(1000,3),YPL(1000,1),YPV(1000 1) ,Q(6)'DIMENSION FAIRTT(0),EFILMT(400)FGAST(400),FVEL(400)COMMON/AA/ N IRZIRDIRDZ,TRARTIRAR IRMIRSBOLZ,RADGHA XLONGRHOG,1'SIATnCLATD,P ,PZFRFSOLA ,AUV LP ,GAMMA,RG ,GC4 C6 ,PRG ,WGPOSS,CR,2ClTWFCP,VE,ALPHARFTA,Fr)FH2,OFH3,'FH4,)FH7,CSI CCIRCOMMON/RB/ZZ,NT,TZA ,TZBRTZ,TZCOMMON/CC/GMTSCOMMON/DD/TARHO,PHI,CDCOMMON/EE/QCOMMON/SHARE/RAXXO,F,Y,AHAM AS RFN,RT
KIP=OTHIPDn=. /3.FSOL=96.SBOLZ=3.6995F-10XMA=28.9644R=1545.32PA = R/XMAG=32.1740RAD = (4.0*ATAN(1.O))/180.0
1001 READ 995,(TITLE(I),I=1,8)RFAD 20,ITTF(TT) 998,9QR,1000
998 WRITE(6,994) (TITLE(I),I=1!8)WRITF (6950)CALL FXIT
1000 ,GOTc( lO0,?On ,40, ,OO O ,7nn ^ , oO, 00,^O o, , ^ /^On) T
C**DATA PRINTOUT SECTION****************************************
100 IF (KIP.FQ.1) GO TO 2013WRITF (6,994) (TITLF(I),T=i,8)WRITF (6,2000)1=3WRITF (692001) IWRITF (6,3000)WRITF (6,200?) Cl C4 ,r6,ARITRFMIRARUV1=4WRITF (69 2001) IWRITE (694000)WRITF (6,2002) WPB,WF ,VRMFL-n, CRZMIN1=5
WRITE (6, 2001) IWRITF (6,5000)WRITE (6, 2002) TGO,TFOZO, Y20,DEC,XLAT,XLONGt=6WRITE (6, 2001) IWRITF ( 6, 6000)WRITF (6, 200?) HDPR,Xf,XT,GMTS,GHADPLTT=7WRITF (6, 2001) IWRITE (6,7000)
108
rO 2004 T=1,NST2004 WRITE (6,2005) TCSI(I),CCSI(I)
T=8WRITE (6, 2001) IWRITE(6,8000) VODO 2007 T=1,NVI
2007 WRITE (6,2005)TV(I),VV(I)I=9WRTTF (69 2001) IWRITF (6,9000)R1n 200R T=1,NRT
200R WRITF (6,2005) TR(I),BR(T)T=10WRITE (6, 2001) IWRITE (6,1010) RHOO00 2009 1=1 ,NT
2009 WRITF (6,2005) ZZ(I),TZ(I)I=11WRITF(6,2001) IWRITF(6,1100).o 2010 T=1 NTR
2010 WRITE (6,2005) 7IR(I),RTTR(I)T=12WRYTF (6, 2001) IWRITF(6,1111)DO 2011 T=1,NFX
2011 WRITF (6,2005)FTIMF() ,FALT( I)EAIRT(I),EFILMT(I),EGAST(I) FVEL(I)1=13WRTTF (6, 2001) TWRITF (6 1300)) 72012 =l ,NCTP
201? WRITF (6.,2?Oo) TIR(I),CIR(T)T = 14WRITF (692001) TWRITF (6,1405)WRITE(6,1500) PRG, ALPHA, FFTA, GAMMA,XMGCP,CVc, Tn 2013
200 PRINT 994CALL FXIT
C**DATA REAnIN AND INTERPOLATION SECTION********************************
300 RFAD 2nITT(XX(I),I=1,7)IP=3IF(IT) 997,302,970
o0? (l = XX(1)
C4=XX(2)C6 = XX(3)ARIR = XX(4)FMIR = XX(5)ARUV = XX(6)PFAD 20,ITIF(IT) 997,971 1 100
400 RFAD 20, IT, ( XX(I), =1,7 )IP=4IF(IT) 997,402,970
109
402 WPR=XX(1)WF =XX (?)VRM=XX (3)FLO=XX (4)CR = XX(5)ZM IN=XX (6)READ 20,ITIF(TT) 997,971,1000
50, RFAD 20,TT,(XX(I),I=1,7)
IP=5IF(TT) 997 502,970
50? TGO=XX(1)TFO=XX(2)ZO=XX (3)Y20=XX(4)DFC=XX (5XLAT=XX(6)XLONC=XX(7)RFAn ?0,TT
TF ( TT) 097,971 ,1 OnC
95, READ 20,IT,(XX(I),I=1,7)TP=6IF(IT) 997,952 970
95? H = XX( )DPR=XX(2)XO=XX(3)XT=XX ()GMTS=XX (5)CHA=XX (6)DPLT = XX(7)HSTOR=HPFAtn 7n,TTTF(TT) 997,971 1000
70, TP=7
nO 701 T=1,100READ 20 , IT, TCSI(I ) CCST(I)IF (T)9977701 ,704
701 CONTINUFRFAD 20, ITIF(TT) 997,071 706
7nh T= T+704 NSI=T-1
nr 705 J=2,NST
DnsIDT(J-1)=(CCST (J)-CS (J-1))/(TCSIJ! -TSI(J-1))705 (ONTTINUF
GOTO 1000
800 READ 20, IT, XX(1)TP=RIF (T)997,802s970
80? VO = XX(1)nO 801 T= 1,100RFAD 20, TT. TV(I), VV(T)I (IT) 99-7801,804
801 CONTTNUJE
110
RfAfn ?0, TTIF(IT) 997 071t 05
805 I=1+1804 NVI=I-1
GO TO 1000
900 READ 20, IT, XX(1 )IP=oIF(IT) 997,902,970
90? CONT INUFPR = XX ( )nnO 903 T=1,100)READ 20, IT, TR(I ), BR(I)IF (T) 997,90 ,905
903 CONTINU JFREAD 20, ITIF(IT) 997,971,904
004 1=1+1900 NRI=T-1
GO TO 00o0
6n PFAD ?0, IT, XX(I )TP=1TF( T) 907 602? 70
60? RHOO= XX(1)rn 6n03 T=1 100RFAD 20, IT, Z7(I), TZ(T)IF (IT) 997, 603, 608
603 CONTINUFREAD 20, ITIF(IT) 997,971,609
609 I = 1+16hn NIT = T-1
PTZ(1) = RHnO * T7(1)rn 604 =?, NITIF ( T7(I) -TZ(I-l)) 605, 6n6, 605
605 TZA(I-1) = ( TZ(I - TZ(T-1))/(ZZ(TI -ZZ(I-l))TZR( -1 ) =(ZZ( ) *TZ(I-1) - ZZ(T-1) * TZ(T)) / (ZZ(T) - ZZ(T-l))RTZ(T) = RTZ(I-1) *(TZ(1-1)/T Z(I))**(1./(RA*TZA(T-1)) )GO TO 604
606 TZA( 1-1) = 0.0TZB( I-1) = TZ(I)RTZ(I) = RTZ(I-1) *EXP ((ZZ(I-l)-ZZ(I))/(RA*TZ(I-1)) )
604 CONTINUEr)0 TO Innn
96^ TP= 11no 961 T=1,100RFAn 20,TTZTR( T) ,RTTR(I)
C** FOUATION 51 - INFRARED HEAT FLUX TO FABRIC FROM BLACK PALL TFMP PROFILE ****IF( IT )997,961 962
961 CONTINUERFAD 20, ITIF ( IT) 997,971 964
964 T=1+1962 NIR=I-1
n 9P63 J=2?NIPDIRDZ(J-I)=(RTIR(J)-RTIR(J-1))/(ZIR(J)-ZIR(J-1))
11
963 CONTINUEGOTO 1000
qsn IP=1?DO 984 MZY=1 400ETIME(MZY)=0.FALT(MZY)=0.FAIRT(MZY)=O.EFILMT(MZY)=0.FGAST(MZY)=0.FVEL(MZY)=0.
984 CONTINUEDO 981 I=1,400READ 20,ITET IME(I),EALT(I),EAIRT(I)EFILMT(I) EGAST(I),EVEL(I)IF(TT)997,981 982
981 CONTTNUFREAD 20, ITIF(IT) 997,971,983
983 - I+l982 NFX= I-
GO TO 1000
1400 TP=13nO 1401 T=1t,00READ 20, IT,TTR(fI) CIR(I)IF ( IT)997,1401 1402
1401 CONTINUEREAD 20, ITTF(IT) 997,97191403
1403 1=1+1140? NCIR=I-1
D01404 I=2?NCTRDC IRDT( I-1)=(CIR(I)-CIR(T-1l/(TIR(I)-TIR(I-1 )
1404 CONTINUEGO TO 1000
3020 READ 21,IT,(XX(I),I=1,7)IP = 14IF(TT) 997,3022, 970
3022 CONTINUEPRG = XX()1ALPHA = XX(2)BETA = XX(3)GAMMA = XX(4)XMG = XX(5)CP = XX(6)CV = XX(7)RG = R/XMGRFAD 20, ITIF(IT) 997,97111000
997 WRITF(6,994) (TITLF(I),I=19l )WRITF (6,80) IPCALL FXIT
970 WRITE(6,994) (TITLE(I),I=1,8)WRITE(6,60) IPCALL FXIT
971 WRITE(6,994) (TITLE(I)tI=1,8)WRITE (6,70) IP
112
CALL EXIT
C**INTT ALTZTNG VARTARLFS AND PARAMFTFRS*******************************
2013 CLATD=COS (XLAT*RAD)*COS (DEC*RAD)SLATD=SIN (XLAT*RAD)*SIN (DrC*RAD)
C FOR THE FIRST 60 SECONDS, ONE SECOND INTERVALS ARE USED.H = 1.0CALL RHOT(0.,TEMP)PZER=RT*RAY(1 = ZO
Y(?)=Y;'0Y(3) = TFOY(4)=TGOX = XO
IF (X -TV(1)) 102,1021 9021102 WRITE (6,40) X, TV(1)
WRITE (6,45)GO TO 996
1021 CONTINUFIF(X-TR(l)) } 111 112,t11?
ll WRITF (6,56) XTP(1)WRITF (6,45)GO TO 996
111? CONT NUFIT(X-TCSI (1) )1?211211 ,121
121 WRITF(6,65) X, TCSI(1)WRITF (6, 45)GO TO 996
1211 CONTINUEIF(X-TTR(1) )126,1261,1261
126 WRITE (6,81) XTIR(1)WRITE (6, 45)GOTO 996
1261 CONTINUFXP= XOVTF=XOVA.LD=O.LP=5SIY=ONYC=0LAST=0tH=0C1TWF=C1*WFCALL RHOT(Y(1),TFMP)RHO = RT / TFMPP=RT*RATA = TFMPWGROSS=WPR+WFFL=ELOY(5)=(FL+WGROSS)/((XMA*Y(4) /(XMG*TA)-1,WGO=Y( 5)Y(6)=RG*Y(5 )*Y(4)/PDO 99 I=1,6Q( I )=0.
99 CONTINUECSI=CCSI (1)CCIR=CTR( 1)
113
PHI=Y(6)**THYRD
C**INITIALIZING TOTAL ENERGY, E1****************************************
CALL YPRTMFDKE=(WGROSS+Y(5)+CB*RHO*Y(6))*Y(2)*F(2)/GDPE= (RHO*Y(6)-WGROSS-Y(5))*Y(2)DDRAG=CD*.60375*PHI**2.*RHO*Y(2)*ABS (Y(2))*Y(2)/GDEWA=P*F(6)DEVE=Y(4)*CP*F(5)ETOT=CV*Y(5)*Y (4)+C1*WF*Y(3)FTOT1=FTOTENET=.OFP=0.OECHK=0.
C**BEGIN NEXT ITERATIVE STEP********************************************
101 LAMBDA=0DO 104 I=2,100IF (TV(I)- X) 104,104,105
104 CONTINUFWRITF(6,108)GO TO 996
105 V= VV(I-t)+VOCONTINUE
Dn 11t3 = 2, 100IF ( X - TR(I)) l16, 11 3 113
11 CONTINUFWRITF (6,125)GO TO 996
116 B = PR (-I )+ROCONT INUF
WGROSS=WGROSS-R*HIF (WGROSS-WF) 109,109,9120
109 WRITF(6,15)GO TO 996
120 00 12? I=2,NSI
IF(X-TCSI(I )+.5*H)124,123,123123 CONT NUF124 CSI=DSIDT(T-1)*(X-TCSI(I-1))+CCSI(I-1)
DO 128 I=2,NCTRIF(X-TIR(I)+.5*H)129*128,128
17R CONTINUF12q CCIR=CIR(I-1)+OCIRDT(I-1)*(X-TIR(I-1))
IF (IY)130,153,1301.5 3 TY=1
GOT0140
130 F = 0.XS = X
DO 131 I=16131 Y(I+10) = Y(I)
114
CALL RNGKTA (Ho 6 1 1 )IF(Y(6)-VRM)160,160,133
16^ CONTINUEPHI = Y(6)**THIRD
C**INCREMENTING TOTAL FNERGY********* ************ **-******************
CALL YPRIMEDKE=(WGROSS+Y(5)+CB*RHO*Y(6))*Y(2)*F(2)/GDPE= (RHO*Y(6)-WGROSS-Y(5))*Y(2)DDRAG=CD*.60375*PHI*PHI*RHO*Y(2)*ABS (Y(2))*Y(2)/GDEVE=Y(4)*CP*F(5)DFWA=P*F(6)FL=Y(5)*((XMA*Y(4))/(XMG*TA)-l1)-WGROSSEP=EP+(-DKE+DPE-DDRAG-DEWA+DFVE+DEH2-DEH3+DEH4+DEH7)*HVALn=VALr)+H*V/( ((XMA*Y(4)))/(XMG*TA )-.1 )ETOT=CV*Y(5 )*Y(4)+C1TWF*Y(3)FNET=FTOT-~TOTECHK=(ENET-EP)/ENETGO TO 140
133 CONTINUEDO 135 LAMRDA=19 20F = F + ( VRM - Y(6)) / HX = XSDr 1t6 T=I1Y(I) = Y(+l10)
136 CONTINUECALL RNGKTA ( H, 6, 1, 1)IF(Y(6)-VRM)160,160,135
13, CONTINUFPRINT 25GO TO 133
140 IF( (Y(1)+(0.5*F(2)*H+Y(2))*H) .GT. ZMIN )GO TO 142IF (LAST.EQ.1)GO TO 141HSTOR=HLAST=InZMTN=Y(I )-ZMTN
148 HST=HH=H-((0.5*F(2)*H+Y(2))*H+nZMIN)/(F(2)*H+Y(2))IF(ABS(HST-H).GT0.1 )148,142
141 IX = 1GO TO 150
142 IF ( X -XT) 1449 1419 141144 IX=2150 IF(X-(X0+60.))156,154,155154 H=HSTOR-AMOD(60.,HSTOR) $ GO TO 156155 IF(IH.EQ.1)GO TO 156 $ IH=1 $ H=HSTOR156 CONTINUE
C**CONVERT PROGRAM VALUES TO PRINTFR AND PLOTTER OUTPUTS****************
IF( (DPLT.EQ.O.) .OR. (X.LT.VTF) )GO TO 171CALL TIMEVTM = AH + (AM*60.0 + AS)/3600.0NYC = NYC + 1TC = 459.67
115
YPT(NYC1 ) = TA - TCYPT(NYC,2) = Y(3) - TCYPT(NYC.3) = Y(4) - TCYPH(NYC91) = Y(l)YPV(NYC,1) = 60,0*Y(2)YPL(NYC,1) = FL/ WGROSS * 100.0XPT(NYC) = VTMVTF=X+DPL T
171 CONTINUEC**PRINT OUTPUT*********************************************************
IF(TX.FQ.1),O TO 143IF(X-XP) 157,143*143
143 CONTINUEXP = XP + rPRIF(LP-55)146,146,147
147 CONTINUEWRITE (69994) ( T+TLF(JS)9 JS 3 IT 8DWRITE (60976)LP = 0
146 CONTINUEPERB=100.*(WF+WPR-WGROSS)/(WPB)PERV=100.*VALD/WGOPERE=100.*(WGO-Y(5))/(WGO)-PERVVEL=60.*Y(2)PM = 0.478802516 * PXMIN=X/60.CALL TIMEWGP=WGROSS+Y(5)WRITF (69 977) AHAMASXMIN,Y(1),VFL,PMTA,Y(3)IY(4),Y(6 ,W
1GPY(5) ,FLPFRR PERV PERF LAMPBAFCHKLP= LP+1
157 CONTINUEC**CALL PLOT ROUTINE****************************************************
IF(IX.EQ.2)GO TO 101IF(DPLT.EQ.O.)GO TO 996CALL YPLOT(NYC,3,XPTYPT,1)CALL YPLOT(NYC91,XPT,YPH,2)CALL YPLOT(NYC,1,XPTYPV,3)CALL YPLOT(NYC,1,XPT,YPL-4)
996 READ 209 ITIF(IT.EQ.2) GO TO 200IF(IT.EQ.O) GO TO 1001WRITE (69993)CALL EXIT
C**INPUT AND OUTPUT FORMATS*********************************************15 FORMAT (77H1 YOU HAVE NOW THROWN AWAY ALL OF THE BALLAST - - INCLU
1DING THE GONDOLA./1HO/1HO)20 FORMAT ( TI2 7F10.4)21 FORMAT( 12* 7F100 )25 FORMAT(* ITFRATION DOES NOT CONVFRGF*//)40 FORMAT ( 7H1 TIME=F10.598H TV(1)=F10.5)45 FORMAT(15H TNPUT IS WRONG/IHO/1HO)50 FORMAT (31H CARD AFTER TTTLE CARD IS WRONG/1HO)55 FORMAT(7H1 TIME=F10.58H TB(1)=F10.5)60 FORMAT (9H NO TYPE I295H DATA/1HO)
116
65 FORMAT ( 7H1 TIME=F10O.59H TCSI(1)=F10.5)70 FORMAT (15H TOO MANY TYPE I295H DATA/1HO)80 FORMAT (20H IT AFTER DATA TYPE I2,12H IS NEGATIVE/1HO)81 FORMAT(7H1 TIME=F10.58H TIR(1)=F10.5)
108 FORMAT (28H1 X IS GREATER THAN TV(100)/1HO/1HO)125 FORMAT (28H1 X IS GREATER THAN TB(100)/1HO/1HO)976 FORMAT(1HO03X,3HGiMT 6X 4HT MF 2X 8HALT ITUDF,4X3HVFL,3X,5HPRESS 4X
1,2HTA,5X,2HTXHTF,5X2HTG5X,6HVOLUME3X,5HTMASS92X6H GMASS,2X97HFR LI.2FT,2X,4HPERB,2X,4HPERV 2X,4HPERE,2X 3HIRS,3X,4HECHK/2X*H M S*35X*MIN*5X*FT*7X*FPM*5X*MR*6X*R*6X*R*6X*R*6X*CU FT*4X*LBM*5X*LBM*47X*LR* / )
977 FORMA ( 3F3.0,1XF7.0,2XF7.0,2XF6.0,2F61XF6512XF51 2XF5.lt2XF15.12XF8 0XF*Ot2 2XF2XF8.02XF6 2XF6 2XF7 2XF412XF4.12XF4.1,2X I22XF63)
993 FORMAT(1H1952H CARD AFTER CARD TYPE 1 OF PREVIOUS PROBLEM IS WRONG1/1HO)
994 FORMAT(1H1,8A]0)995 FORMAT(8A10)1010 FORMAT(1H+8X*RHOO =*F10.5/11X*ALT*12X*TEMP*)1100 FORMAT(1H+1OX*ALT*11X*RTEMP*)1111 FORMAT(1H+8X,*FTIME*912X,*EALT*11X*EAIRT*O1X*EFILMT*11X,
l*FGAST*12X*EVFL*)1300 FORMAT(1H+8X*TIME ETHIR*8X*CIR*)1405 FORMAT(1H+9X*PR.NO.* 12X*ALPHA* 13X*BETA* 12X*GAMMA* 10X*MOL.WT.*
115X,*CP*, 15X,*CV*)1500 FORMAT(4X9 7(E15.6,2X))2000 FORMAT(1HO,11H INPUT DATA)2001 FORMAT(1HO,4H IT=I2)2002 FORMAT(7F16.5)
2005 FORMAT(6F16.3)3000 FORMAT(1H+11X*C1*14X*C4* 14X*C6*12X*ABIR*12X*EMIR*12X*ABUV*)4000 FORMAT(1H+7X*PAY+BLST*6X*FABRIC WT*12X*VOL*12X*F.L.*14X*CB*12X*ZMI
1N*)5000 FORMAT
* (1H+10X*TGO*13X*TFO*14X*ZO*12X*ZVEL*13X*DEC*13X*LAT*12X*LONG*)6000 FORMAT(1H+8X*DTIME*10X*DPRINT*11X*ZTIME*11X*ENDTIME*12X*GMTS*
* 13X*GHA*12X*DPLT*)7000 FORMAT(1H+8X*TIMF SUNIR*7X*CCSI*)8000 FORMAT(1H+8X*MAN VALVE =*F1O.5/9X*VTIME*12X*VDOT*)9000 FORMAT(1H+8X*MAN BLST =*Fl0.5/9X*BTIME*12X*BDOT*)
FND00562
117
SUBROUTINE YPRIMETDMFNSION Y(16),ZIR(100),F(6),DIRDZ(100),RTIR(100)
COMMON/AA/ NIR,ZIRDIRDZRTIR,ABIREMIRSBOLZRAC GHAXLONGRHOG,1SLATDCLATDP,PZERFSOL,ABUV LP,GAMMARGG C4 C6,PRGWGROSS CB2C1TWF,CP,V,E,ALPHABETA,DEH2,DEH3,DEH4,DEH7,CSI CCIRCOMMON/DD/TARHOPHICOMMON/SHARE/RAX,XO,F,YAHAMASRENRTDATA THIRD, TRZ, RETH/ .33333333333339 459.67, 20903520. /SBOLZ=3.6995E-10CALL DRAGC(CD)CALL RHOT(Y(1),TA)P=RT*RARHO = PT / TAPHI=Y(6)**THIRDPHISQ=PHT*PHIDO 181 I=2,NIRTF(Y(1)-ZIR(I ))182,181,18l
181 CONTINUEGO TO (184,183),IXY
184 PRINT 20,XY(1)IXY=2GO TO 183
182 IXY=1183 TIR=DIRDZ(I-1)*((Y(l)-ZIR(I-1))) +RTIR(I-1)
FLUX R=SROLZ*T R**4C** EQUATION 50 - ABSORPTION OF INFRARED RADIATION BY BALLOON FABRIC *****N*****
DEH2=CCIR*ABIR*4.83*PHISO*FLUXIRC** EQUATION 32 - EMISSION OF INFRARFD RADIATION BY BALLOON FABRIC *************
DEH3=EMIR*4.83/PHISQ*SBOLZ*(Y(3)**4)C** FQUATION 43 *************-*************************************************
XLAH=RA)*(GHA-X ONG+X/240.)C-** EQUATION 33 ****-********************************************************
CAM= SLATD + CLATD* COS (XLAH)IF (CAM) 100,101,101
C** EQUATION 36 - AIR MASS CALCULATION ****************************************101 AIRM= (P/PZER)*(SQRT(1228.6 +376750.44*CAM*CAM)-613.8*CAM)
C** FQUATION 35 - ATMOSPHFRIC TRANSMITTANCE TO SOLAR RADIATION **********.*****TRANS=.5*(FXP (-.65*AIRM)+EXP (-.095*AIRM))FLUXUV= FSOL*TRANS *CSIGOTO 110
100 CAL=RETH/(RETH+Y(1))CAMM=-SQRT(1.-CAL*CAL)IF (CAMM-CAM)102,103,103
102 ZZ1=(RETH+Y(1))*SQRT(1.-CAM*CAM)-RETHCALL RHOT(ZZ1,TTT)PZ1 = RT*RAAIRM1=35.1*PZI/PZERAIRM2=(P/PZER)*(SQRT(1228.6+376750.44*CAM*CAM)+613.8*CAM)TRAN1=.5*(EXP (-.65*AIRM1)+EXP (-.095*AIRM1))TRAN2=.5*(FXP (-.65*AIRM2)+EXP (-.095*AIRM2))FLUXUV=FSOL*CSI*TRAN1*TRAN1/TRAN2GOTO 110
103 FLUXUV=0.110 CONTINUE
DEHH7=DEH7C** EQUATION 42 - RATE OF ABSORPTION OF SOLAR RADIATION BY BALLOON FABRIC*L*****
DEH7= ABUV*1.208*PHISQ*FLUXUV
118
IF(DFHH7) 111 111 115111 IF(DFH7) 119119,114114 IF(X-XO)119,119,120120 INM=1
GO TO 121117 WRITF (6,113) AH, AM, AS
118 LP=LP+3 $ GO TO 119115 IF(DFH7.GT.O.)GO TO 119
INM=2121 CALL T IM
GO TO(112,116),INM116 WRITE (69117) AH, AM, AS $ GO TO 118119 VISA = (7.30248F-07 * TA *SQRT(TA))/(TA + 198.72)
VISG = ALPHA * Y(4)**RFTACG = GAMMA * VISGCAIR = 277.28 * VTSARHOG = P/(RG*Y(4))GR = ABS(RHO*RHO*G*(TA-Y(3))*Y(6))/(TA*VISA*VISA)*1.91EC = 0.0IF(RFN.EQ.0.0) FC = 2.0IF(EC.GT.1.O) GO TO 200EC = GR/(REN*REN)
200 CONTINUEC** EQUATION 20 - CONVECTION TO OR FROM FABRIC AT FLOAT ***********************
IF(EC.GT.1.0)DEH4=7.79*PHI*CAIR*(TA-Y(3) )*(1+.322*((RHO*RHO*G** ABS(TA-Y(3))*Y(6))/(TA*VTSA*VISA))**0.25)*C4
C** EQUATION 18 - CONVECTION TO OR FROM FABRIC DURING ASCFNT OR DESCENT ********
IF(EC.LE.1.O) DEH4 = 3.9*PHI*CAIR*(TA-Y(3))*(2.0+O.472*PHI**0.55*(1(RHO*ABS(Y(2)))/VISA)**0.55)*C4
C** EQUATION 28 AND 29 - CONVECTION HEATING OF BALLOON GAS BY FABRIC ***********XNUSG=0.1612*PHI*((RHOG*RHOG*G*PRG*ABS(Y(4)-Y(3)))/(VISG*VISG*Y(4)*))**THIRDDEH6 = 3.895 * C6 * CG * PHI * XNUSG * (Y(3)-Y(4))F(1) = Y(2)
C** EQUATION 5 - BALLOON ACCELERATION FROM BALLOON FORCE BALANCE ***************F(2)=((RHO*Y(6)-WGROSS-Y(5))*G-.6038*CD*PHISQ*RHO*Y(2)*ABS (Y(2)))
1/(WGROSS+Y(5)+CR*RHO*Y(6))C** EQUATION 15 - BALLOON FABRIC ENERGY BALANCE ********************************
F(3)=(DEH2-DFH3+DEH4-DEH6+DEH7)/(C1TWF)C** EQUATION 14 - BALLOON GAS ENERGY BALANCE ***********************************
F(4)=( DEH6-RHO*Y(6)*Y(2))/(Y(5)*CP)C** EQUATION 12 - BALLOON GAS MASS BALANCE ***********************************
F(5)=RHOG-RHOGRHOE-RHOG*V/(RHO-RHOG)C** EQUATION 11 - RATE OF CHANGE OF BALLOON VOLUME *****************************
F(6)=((F(4)/Y(4))+(F(5)/Y(5))+(Y(2)/(RA*TA)))*Y(6)RETURN
20 FORMAT(1HO9H AT TIME=F7.0,75H SEC THE BALLOON WENT ABOVE THE INFR1ARED FIELD SPECIFIED IN THE INPUT DATA./18H BALLOON ALTITUDE=F7.0O26H FEET./123H START TO CONTINUE FLIGHT USING INFRARED DATA OF UPPE3R LAYER OF SPECIFIED FIELD FOR AS LONG AS BALLOON REMAINS ABOVE FI4FLD.)
113 FORMAT (1HO,25X,4HGMT=3F3.0,5X,18HSUNRISE AT BALLOON / )117 FORMAT (1HO925X,4HGMT=3F3.0,5X17HSUJNSET AT BALLOON / )
FND00112
119
SUBROUTINE RHOT(ZT)DIMFNSION ZZ(100),TZ(100),RTZ(100) ,TZA(100) ,TZ( 100) Y( 16) F(6)
COMMON/BB/ZZ NT,TZATZB,RTZ TZCOMMON/SHARE/RA,X,XO,F ,YAH,AM,ASRENRTIF ( Z- ZZ(1)) 100,200, 200
100 J=lGO Tf 203
20,, NM1 = NT-1DO 201 J=1, NM1IF ( Z - ZZ( J+1)) 300, 300, 201
201 CONTINUEJ=NM1GO TO (202,203),IYX
202 PRINT 209XY(1)IYX=2GO TO 203
300 IYX=1203 IF ( TZA(J)) 301, 302, 301301 T = TZA( J) * 7 + TZB (J)
RT=RTZ(J)*(TZ(J)/T)**(I./(RA*TZA(J)))RETURN
302 T = TZB (J)RT=RTZ(J)*FXP ((ZZ(J)-Z)/(RA*T))RETURN
20 FORMAT(1H099H AT TIME=F7.0,63H SEC THE BALLOON WENT ABOVE ATMOSPHE
1RE SPECIFIED IN INPUT DATA./18H BALLOON ALTITUDE=F7.0,6H FEET./1282H START TO CONTINUE FLIGHT USING ATMOSPHERIC DATA OF UPPER LAYER 0
3F SPECIFIED ATMOSPHFRE FOR AS LONG AS BALLOON REMAINS AROVE IT.)
END00030
120
SUBROUTINE TIMEDIMENSION Y(16),F(6)COMMON/CC/GMTSCOMMON/SHARE/RAX XO F ,Y ,AH AM AS RFN RTGT TMF=X-XO+GMTSAH = 0.0HH = GTIME
10 HH = HH - 3600.AH = AH + 1.0
IF(HH.EQ.0.) GO TO 20IF(HH.GT.0.) GO TO 10AH = AH - 1*0
20 HH = (GTIME) - 3600.0 * AHAM = 0.0
30 HH = HH - 60AM = AM + 1.0IF(HH.FQO00) GO TO 40IF(HH.GT.0.0) GO TO 30AM = AM - 1.0
40 AS=(GTIME) - 3600.0 * AH - 60.0 * AM
RFTURNEND
00023
121
SUBROUTINE DRAGC(XCD)C**WRITTEN BY J.H. SMALLEY
DIMENSION Y(16) F(6)COMMON/DD/TARHOPHI , CDCOMMON/SHARE/RA ,XXO ,F,YAH AM AS REN RT
C SUTHERLANDS EQUATION FOR VISCOSITY OF AIRVISA=7.30248E-7*TA*SQRT(TA)/(TA+198.72)REN=1.24*RHO*ABS(Y(2))*PHI/VISAIF( REN.GT. 0.01 ) GO TO 10CD=2400.GO TO 100
10 IF( REN.GT. 1.0 ) GO TO 20C STOKES LAW FOR DRAG COEFFICIENT
CD=24./RFNGO TO 100
2, IF( REN.GT.3E+3 ) GO TO 30XZ=ALOG0 (RFN)Z=(( 0.0185*XZ+ 0.0095 )*XZ-0.748 )*XZ+ 1.385
GO TO 9030 IF( REN.GT.1E+5 ) GO TO 40
CD=0.47GO TO 100
40 IF( REN.GT.3E+5 ) GO TO 50XZ=ALOG10(REN)Z= -1 406*XZ+ 6.702GO TO 90
50 CO=0.5GO TO 100
9, CD=FXP( Z/0.4342944819 )
100 CONTINUEXCD = CDRETURNEND
00034
122
SUBROUTINE RNGKTA(HI N1 ,N2.N3)DIMENSION Q(6),Y(16),F(6)COMMON/FEE/QCOMMON/SHARE/RAX ,XOF ,Y ,AHAM ,ASRFNRTTF(N3-1)2,1,2
1 H=H1HH=.5*HN=!N1M=N?
? Dn 4 J=1 MCALL YPRTMFDO 5 I=1. NS=F(I)*HT=.5*(S-2.*Q(I))Y(I)=Y(I)+T
5 Q( I )=Q( I )+3.*T-.5*SX=X+HHCALL YPRIMFDO 6 I=1,NS=F (I )*HT=.2928932?*(S-0(I))Y(I )=Y(I )+T
6( I)=Q(IT+3.*T -. 29289322*SCALL YPRTMFDO 7 T=19NS=F(I) *HT=1.7071067*(S-( I))Y( I )=Y( I )+T
7 Q(I)=Q(I)+3.*T-1.707106*SX=X+HHCALL YPRTMF
n0 ( TR l=1NS=F ( )*HT=(S-2.*O( T )/6.Y(I)=Y(I)+T
8 Q(I)=Q(I)+3.*T-.5*S4 CONTINUF
RFTURNFN0
00040
123
SUBROUTINE YPLOT(N,MXYNG)C**WRITTFN BY J.H. SMALLFY
DIMENSION Y(10003) ,IA(120),PTS(11) IHP(10),X(1)DIMENSION IS(12), IL(24), IY(8), CC(10), IFMT(2)DATA IF,TF /1HE1HF/
C N=NO. OF DATA POINTS, M=NO. OF CURVES PER GRAPH, NG=NO. OF GRAPHSC CC=ARRAY OF ADMISSIBLE RANGES OF THE Y-AXIS SCALEC IS=SYMBOL ARRAY, DIMENSION=NSYM*NGC IL=LEGEND ARRAY, DIMENSION=NSYM*NG*2C IY=Y-AXIS LABLE ARRAY, DIMENSION=2*NGC NSYM=MAXIMUM NO. OF SYMBOLS (CURVES) PER GRAPH
DATA NSYM/ 3 /DATA CC/ 1.,2.,3.,4.,5.,6.,8.,10.,15.,20. /DATA IS/ 1HA,1HF,1HG9 1HH,1H ,1H * 1HV,1H ,1H , 1HL,1H ,1HDATA IY/ 20HY AXIS = DEGREES (F), 20HY AXIS = FEET* 20HY AXIS = FEET/MINUTE, 20HY AXIS = PERCENTDATA TL/ 20HA = AMBIFNT AIR TFMP, 20HF = FILM TFMP
* 2CHG = BALLOON GAS TFMP,* 20HH = BALLOON HEIGHT , H ,1H ,1H ,1H* 20HV= VERTICAL VELOCITY, 1H ,1H ,1H ,1H 9* 20HL = FREE LIFT , 1H ,1H ,1H ,1H
CNGM1=NG-1 $ NSNG1=NSYM*NGM1NCONI=2*NGM1+1 $ NCON2=2*NGMI+2DO 100 I=1 ,M
100 IHP(I) = IS(NSNG1+I)DO 2 J=1,170
2 IA(J)=1H
C FIND Y-SCALE FXTREMES AND CHARACTFRISTICSYMAX=Y(5,1) $ YMIN=Y(1,1)DO 1 I=1,M $ DO 1 J=1l,YMAX=MAX1F(Y(J,I),YMAX)
l YMIN=MIN1F(Y(J,I),YMIN)YDIF=YMAX-YMIN $ YM=AMAX1(ABS(YMAX),ABS(YMIN))PT=INTF(ALOGlO(YDIF)) $ IF(YDIF.LT.1.)PT=PT-1.PP=ATNT(ALOGl0(YM)) $ IF(YM.LT.1.)PP=PP-1,IF(YMIN*YMAX.LTO.)PT=PPFM=10.**(PT-1.)SU=AINT(YMAX/FM) $ SL=AINT(YMIN/EM)TF((YMAX.GT.O.) .AND. (YMAX.GT.SU*EM))SU=SU+1.IF((YMIN.LT.O.) *AND. (YMINLT.SL*FM))SL=SL-1.
C MODIFY Y-SCALF TO A MORE USEFUL SCALE10 SS=SU-SL $ IF(SS.GT.?0.)SS=SS/10.
DO 1? =1,l10TF(SS-CC(I)) 13, 17, 12
13 CCM=CC(I)*EM $ IF(CCM.LT.YDIF)CCM=10.*CCM $ 1=10SD=AINT(CCM/EM+0.5) $ SC=SD/10.
12 CONTINUEIF(SU.FQ.0,)GO TO 14IF(SL.FQ.O.)GO TO 15IF(SU*SL.GT.O.)GO TO 18IF(AMOD(SLSC) )14915
14 SL=SL-1. $ GO TO 1015 SU=SU+l. $ GO TO 1018 IF(ABS(SU).GT.ABS(SL))GO TO 19
124
SUA=SU-AMOD(SU,10() $ IF(SUA-SD.GT.SL)SUASU-AMOD(SU,5 )IF(SUA-SD.GT.SL)GO TO 15SU=SUA $ SL=SU-SD $ GO TO 17
19 SLA=SL-AMOD(SL910.) $ IF(SLA+SD.LT.SU)SLA=SL-AMOD(SL,5*)TF(SLA+Sn.LT.SU)GO TO 14SL=SLA $ SLU=SL+SD $ GO TO 17
C
C START THE GRAPH17 PRINT 1616 FORMAT( 1H1 )
Dn 32 I=1.M $ K=2*(NSNGI+I)-132 PRINT 111, IL(K), IL(K+1
111 FORMAT( 1X9 2A10 )PRINT 110, IY(NCON1), IY(NCON2)
1l1 FORMAT( 41X, *X AXIS = GMT (HOURS) * // 41X, 2A10 / )PTS(1)=SL*FM $ DTS=FM*(SU-SLL)/1 .D n 'O j =I , 1n
30 PTS(J+1) = (PTS(J) + DTS)C nFTERMINF THF FORMAT FOR THE Y-ScAl.F
IP=INT(ALOG10(DTS)) $ TF(rOTS.LT..) IP=IP-lIF((SD.FQ.15.).OR.(SD.EQ.150.))IP=IP-1Tr)=0 $ TF (IP.LT.O) in=lD AS( IP )
IF((ID.NE.O).AND.(ID+PP.lGT.8.))II=INT(8.-PPIENCODF( 20,31,IFMT ) IFID, IF,Tn
31 FORMAT( *(1H * A1, *10.* I19 *,10* Al *11.* I1, * /* )II=l $ IF((PP.LT.O.).AND.(ID.GT.91 )ENCODE(2031,IFlMT)IFEIIIETIPRINT IFMT, (PTS(J) J=1,11)SC=SL*FM $ DTS=SU*EM-SCNZ= 0.+INTF ( -SC/FTS* 1 10.+.5 )IF(NZ.LT.10)NZ=1O $ IF(NZ.GT. 120)NZ=120rXP=(X (N)-X ( 1 ) / ( - ) I=n
C PLOT POINTS, AXIS AND X-SCALFnn 40 J=1 ,XDO=X(I)+(J-1)*nXP
42 DO 29 I= ,M46 II=II+l $ IF(II.LE.N)GO TO 447
TI=N-1 $ rO TO 48447 IF(XDO-X( I ))47,46,46
47 TT=T1-1 $ TF(II.G..1)GO TO 448t=1 $ cO TO 48
448 IF(XnO-X( T))47,48,4848 YP=Y(IIT I)+(Y(T +1,I )-Y(IIT T /(X(1+ 1)-X( II )*(XDO-X(I I
NW=10.+INTF((YP-SC)/DTS*110.+.5)
TF(TA(NZ).F0.1H )TA(NZ)=1HT29 IA(NW)=IHP(I)
WRITE (6,33 (IA(K) ,K= ,120)33 FORMAT( 20?A1
IF(XMODF(J-1,10).EQ.O) PRINT 44, XDO44 FORMAT( 1H+, F6.2, 2X1H+, 1(lOX1H+ ))
nO 34 K=l,120
' 4 IA(K)=1H40 CONTINUE
RFTURN'ND
00113
125
REFERENCES
1. Gibbs-Smith, C. H., 1948: Ballooning. Penguin Books, London,40 pp.
2. Dollfus, C., 1961: The Orion Book of Balloons. The Orion Press,New York, N.Y., 108 pp.
3. Lally, V. E., 1967: Superpressure Balloons for Horizontal Sound-ings of the Atmosphere. NCAR Technical Note TN-28, Boulder,Colo., 25 pp.
4. Kreith, F., and J. C. Warren, 1970: Thermal Analysis of Balloon-borne Instrument Packages. NCAR Technical Note TN-45, Boulder,Colo., 25 pp.
5. Iversen, H. W., and R. Balent, 1951: A correlation modulus forfluid resistances in accelerated motion. J. Appl. Phys. 22(3),324-328.
6. Robertson, J. M., 1965: Hydrodynamics in Theory and Application.Prentice Hall, Englewood Cliffs, N.J., 652 pp.
7. Schlichting, H., 1968: Boundary Layer Theory, 6th ed., McGraw-Hill, New York, N.Y., 746 pp.
8. Germeles, A. E., 1966: Vertical Motion of High AZtitude BaZZoons.Tech. Rept. No. 4 prepared for Office of Naval Research by A. D.Little, Inc., Cambridge, Mass., 88 pp.
9. S. L. Valley, Ed., 1965: Handbook of Geophysics and Space Environ-ments, McGraw-Hill, New York, N.Y.
10. Kreith, F., 1965: Principles of Heat Transfer, 2nd ed., Inter-national Textbook Co., Scranton, Pa., 620 pp.
11. Yuge, T., 1960: Experiments on heat transfer from spheres includ-ing combined natural and forced convection. J. Heat Trans. C-82,214-220.
12. Vliet, G. C., and G. Leppert, 1961: Forced convection heat trans-fer from an isothermal sphere to water. J. Heat Trans. C-83,163-175. (See also discussions by R. M. Drake, J. Kestin, andP. D. Richardson.)
13. Merk, H. J., 1959: Rapid calculations for boundary-layer trans-
fer using wedge solutions and asymptototic expansions. J. FZuidMech. 5, 460-480.
126
14. Fage, A., 1937: Pressure distribution for flow past spheres. Brit.Aeronaut. Res. Cor. R. & M. No. 1766.
15. Krause, A. A., and J. Schenk, 1965-66: Thermal free convectionfrom a solid sphere. Appi. Sci. Res. A-15, 397-403.
16. Merk, H. J., and J. A. Prins, 1954: Thermal convection in laminarboundary layers, Pts. I, II, and III. Appi. Sci. Res. A-4, 207-221.
17. Garner, F. H., and R. B. Keey, 1958: Mass transfer from singlesolid spheres, Pt. I. Chem. Eng. Sci. 13(9), 119-129; alsoGarner, F. H., and R. B. Keey, 1959: Mass transfer from singlesolid spheres, Pt. II. Chem. Eng. Sci. 14( ), 218-229.
18. Garner, F. H., and J. M. Hoffman, 1961: Mass transfer from singlesolid spheres by free convection. AIChE J. 7, 148-152.
19. Schutz, G., 1963: Natural convection mass-transfer measurements onspheres and horizontal cylinders by an electrochemical method.Int. J. Heat Mass Trans. 6, 873-879.
20. Gebhart, B., 1969: Natural convection flow, instability, and tran-sition. J. Heat Trans. C-91, 293-309.
21. Fendell, F. E., 1968: Laminar natural convection about an iso-thermally heated sphere at small Grashof number. J. FluidMech. 34, 163-176.
22. Boxi, C. B., and A. Ramachundran, 1969: Effect of vibration onheat transfer from spheres. J. Heat Trans. C-91, 337-344.
23. Kreith, F., L. G. Roberts, J. A. Sullivan, and S. N. Singh, 1963:Convection heat transfer and flow phenomena of rotating spheres.Int. J. Heat Mass Trans. 6, 881-895.
24. Nordlie, R. L. and F. Kreith, 1961: Convection from a rotatingsphere. Int. Dev. in Heat Transfer, ASME, New York, N.Y., 461-467.
25. Borner, H., 1965: Uber den Warme-und Stoffiubergang an umspultenEinzelnkorpern bei Uberlagerung von freier und erzwungenerStromung. VDI-Forschungsheft 512, VDI-Verlag, Dusseldorf, WestGermany.
26. Krischer, 0., and G. Loos, 1958: Warme und Stoffaustausch bei erz-wungener Stromung an Korpern verschiedener Form-Teilung. Chem.Ing. Techn. 30, 31-39.
27. Acrivos, A., 1958: Combined laminar free and forced convectionheat transfer in external flows. AIChE J. 4, 285-289.
127
28. Mori, Y., 1961: Buoyancy effects in forced laminar convectionflow over a horizontal flat plate. J. Heat Trans. C-83, 479-482.
29. Sharma, G. K. and S. P. Sukhatme, 1969: Combined free and forcedconvection heat transfer from a heated tube to a transverse airstream. J. Heat Trans. C-91, 457-459.
30. Lichfield, E. W. and N. E. Carlson, 1967: Temperature Control ofBalloon Packages. NCAR Technical Note TN-32, Boulder, Colo.,38 pp.
31. Suriano, F. J. and K.-T. Yang, 1968: Laminar free convection aboutvertical and horizontal plates at small and moderate Grashof num-bers. Int. J. Heat Mass Trans. 11(3), 473-490.
32. Stewartson, K., 1958: On the free convection from a horizontalplate. Z. Angew. Math. Phys. 9, Ser. A, 276-282.
33. Gill, W. N., D. W. Zeh, and E. D. Casal, 1965: Free convection ona horizontal plate. Z. Angew. Math. Phys. 16(4), 539-541.
34. Saunders, 0., and M. Fischenden, 1935: Some measurements of con-vection by an optical method. Engineering, 483-485.
35. Singh, S. N., R. C. Birkebak, and R. M. Drake, 1969: Laminar freeconvection heat transfer from downward facing horizontal surfacesof finite dimensions. In Progress in Heat and Mass Transfer,Vol. 2, Pergamon Press, Oxford.
36. Kimbadi, V., and R. M. Drake, 1960: Free surfaces for prescribedvariations in surface temperature and mass flow through the sur-face. T. R. Mech. Eng. HT-1, Princeton University, 17 pp.
37. Husar, R. B., and E. M. Sparrow, 1968: Patterns of free convectionflow adjacent to horizontal heated surfaces. Int. J. Heat MassTrans. 11(7), 1206-1208.
38. Tyler, B. J., and A. F. Tuck, 1967: Heat transfer to a gas from aspherical enclosure: measurements and mechanisms. Int. J. HeatMass Trans. 10(21), 251-253.
39. Sherman, M., and S. Ostrach, 1967: Lower bounds to the criticalrayleigh number in completely confined regions. J. Appl.Mech. 39(2), 308-312.
40. Hellums, J. D., and S. W. Churchill, 1961: Computation of naturalconvection by finite difference methods, Pt. I. Int. Dev. inHeat Transfer, ASME, New York, N.Y., 984-994.
41. and , 1962: Transient and steady state, free andnatural convection, numerical solutions, Pts. I and II. AIChE J. 8,690-693, 719.
128
42. Powe, E. R., C. T. Carley, and E. H. Bishop, 1969: Free convectiveflow patterns in cylindrical annuli. J. Heat Trans. C-91, 310-314.
43. Eckert, E. R. G., and T. W. Jackson, 1950: Analysis of Free Con-vection Boundary Layer on a Flat Plate. NACA Rept. No. 1015,
7 pp.
44. Clark, A. J., 1968: Cryogenic heat transfer. Advances in Heat
Transfer 5, Academic Press, Inc., New York., N.Y., 325-517.
45. Dingwell, I. W., W. K. Sepetoski, and R. M. Lucas, 1963: Vertical
Motions of High Altitude Balloons. Tech. Rept. II, prepared for
Office of Naval Research by A. D. Little, Inc., Cambridge, Mass.,
119 pp.
46. Ulrich, R. D., D. P. Wirtz, and R. H. Nunn, 1969: Transient heat
transfer in closed containers after gas injection. J. Heat Trans.
C-91, 461-463.
47. Gebhart, B., R. P. Dring, C. E. Polymeropoulos, 1967: Natural con-
vection from vertical surfaces, the convection transient regime.
J. Heat Trans. C-89, 53-59.
48. Dingwell, I. W., 1967: Thermal Radiation Properties of Some Poly-
mer Balloon Fabrics. Tech. Rept. VI, prepared for Office of
Naval Research by A. D. Little, Inc., Cambridge, Mass., 43 pp.
49. Dunkle, R. V., 1963: Thermal radiation characteristics of sur-
faces. In Fundamental Research in Heat Transfer, J. A. Clark,Ed., MacMillan Co., New York, N.Y., 1-31.
50. Hartnett, J. P., E. R. G. Eckert, and R. Birkebak, 1959: The
emissivity and absorptivity of parachute fabrics. J. Heat Trans.C-81, 195-201.
51. Edwards, D. K., 1969: Radiative characteristics of materials.J. Heat Trans. C-91, 1-15.
52. , 1969: Thermal Radiation Measurements. Measuring Tech-
niques in Heat Transfer. E. R. G. Eckert and R. J. Goldstein,
Eds., Advisory Group for Aeronautical Research and Development.
53. Kuhn, P. M., 1969: Environmental Science Services Administra-tion, Boulder, Colo., private communication.
54. Goetzel, C. G., J. B. Rittenhouse, J. B. Singletary, Eds., 1965:
Space Materials Handbook, 2nd ed., TORML 64-40 Air Force Materi-
als Laboratory, Wright-Patterson Air Force Base, Ohio, 712 pp.
129
55. Camack, W. G., and D. K. Edwards, 1960: Effect of surface thermal
radiation characteristics on the temperature control problem in
satellites. In Surface Effects on Spacecraft Materials, F. J.
Clauss, Ed., John Wiley and Sons, Inc., New York, N.Y., 3-54.
56. Gaumer, R. C., and L. A. McKellar, 1961: Thermal Radiative Control
Surfaces for Spacecraft. Lockheed Tech. Rept. LMSD-704014, Lock-
heed Aircraft Corp., Sunnyvale, Calif., 198 pp.
57. Blau, H. H., and H. Fischer, Eds., 1962: Radiative Transfer from
Solid Materials, Macmillan Co., New York, N.Y., 257 pp.
58. Wiebelt, John A., 1966: Engineering Radiation Heat Transfer, Holt,
Rinehart and Winston, New York, N.Y., 278 pp.
59. Kreith, F., 1962: Radiation Heat Transfer for Spacecraft and
Solar Power Plant Design, International Textbook Co., Scranton,
Pa., 236 pp.
60. Zarem, A. M., and D. D. Erway, Eds., 1963: Introduction to the
Utilization of Solar Energy, McGraw-Hill, New York, N.Y., 398 pp.
61. Gates, D. M., 1966: Spectral distribution of solar radiation at
the Earth's surface. Science 151(3710), 523-529.
62. Feigelson, E. M., 1966: Light and Heat Radiation in Stratus Clouds,
U.S. Dept. of Commerce, Springfield, Va., 245 pp.
63. Dunkle, R. V., D. K. Edwards, J. T. Gier, K. E. Nelson, and R. D.
Roddick, 1961: Heated cavity reflectometer for angular reflec-
tance measurements. In Proc. Int. Heat Trans. Conf., ASME-AIChE,
New York, N.Y., 541-562.
64. Edwards, D. K., 1961: Directional solar reflectances in the space
vehicle temperature control problem. ARS Journal, 1548-1553.
65. Raschke, E., 1968: The Radiation Balance of the Earth-Atmosphere
System from Radiation Measurements of the Nimbus II Meteorologi-
cal Satellite. NASA Tech. Note TN D-4589, Washington D.C., 81 pp.
66. Houghton, H. G., 1954: On the annual heat balance of the northern
hemisphere. J. Meteorol. 11(1), 1-9.
67. Fritz, S., 1949: The albedo of the planet Earth and of clouds.
J. Meteorol. 6, 277-282.
68. Coulson, K. L., 1959: Characteristics of the radiation emerging
from the top of a Rayleigh atmosphere: total upward flux and
albedo. Planet. Space. Sci. 1(1), Pergamon Press, London,277-284.
130
69. Hibbs, A. R., 1956: The Temperature of an Orbiting Missile.Progress Rept. No. 20-294, Jet Propulsion Laboratory, Pasadena,Calif., 20 pp.
70. Hottel, H. C., and A. F. Sarofim, 1967: Radiative Transfer, McGraw-Hill, New York, N.Y., 520 pp.
71. Sparrow, E. M. and R. D. Cess, 1966: Radiation Heat Transfer,Brooks Cole Publ. Co., Belmont, Calif., 322 pp.
72. Cunningham, F. E., 1961: Power Input to a Small Flat Plate from aDiffusely Radiating Sphere. NASA Tech. Note TN D-710, Washing-ton, D.C., 15 pp.
73. Goody, R. M., 1964: Atmospheric Radiation. Vol. I. TheoreticalBasis. Oxford Monogr. on Meteoro. , Clarendon Press, Oxford,436 pp.
74. Budyko, M. I., 1956: The Heat Balance of the Earth's Surface.Hydrometeorological Publishing House, Leningrad (trans. by U.S.Weather Bureau, 1958), 259 pp.
75. Kondratyev, K. Y., 1965: Radiative Heat Exchange in the Atmo-sphere (trans. by O. Tedder) Pergamon Press, Oxford, 411 pp.
76. Simpson, G. C., 1928: Some studies in terrestrial radiation. Mem.Roy. Meteorol. Soc. 2.
77. Yamamoto, G., 1952: On a radiation chart. Sci. Rept. Tohoku Univ.,Ser. 5, Geophys., 4, 9-23.
78. Elsasser, W. M., and M. F. Culbertson, 1960: Atmospheric radiationtables. Meteorol. Monogr. 4(23), American Meteorological Society,Boston, Mass., 43 pp.
79. London, J., 1957: A Study of the Atmospheric Heat Balance. FinalRept. AF19, New York University, 122-165.
80. Manabe, F., and F. Moller, 1961: On the radiative equilibrium andheat balance of the atmosphere. Mon. Wea. Rev. 89, 503-532.
81. Davis, P. A., 1963: An analysis of the atmospheric heat budget.J. Atmos. Sci. 20(1), 5-22.
82. Simpson, G. C., 1929: The distribution of terrestrial radiation.Mem. Roy. Meteorol. Soc. 3.
83. Katayama, A., 1966: On the radiation budget of the troposphereover the northern hemisphere, Pt. I. J. MeteoroZ. Soc. Japan44(6), 381-401; also Katayama, A., 1967: On the radiation budgetof the troposphere over the northern hemisphere, Pts. II and III.J. Meteorol. Soc. Japan 44(1), 1-25, 26-38.
131
84. Sasamori, T., 1968: The radiative cooling calculations for appli-cation to general circulation experiments. J. Appl. Meteorol.7(5), 721-729.
85. London, J., 1965: The heat-load on a balloon. Unpublished notes,University of Colorado, Boulder, Colo.
86. Suomi, V. E., and P. M. Kuhn, 1958: An economical net radiometer.Tellus 10(1), 160-163.
87. Bushnell, R. H., and V. E. Suomi, 1961: Experimental flight veri-fication of the economical net radiometer. J. Geophys. Res. 66(9),2843-2848.
88. Suomi, V. E., D. 0. Staley, and P. M. Kuhn, 1958: A direct measure-ment of infra-red radiation divergence to 160 mb. Quart. J. R.Met. Soc. 84(360), 134-141.
89. Kuhn, P. M., 1963: Measured effective long-wave emissivity ofclouds. Mon. Wea. Rev. 91, 635-640.
90. - , and D. R. Johnson, 1966: Improved radiometersonde observa-tions of atmospheric infrared irradiance. J. Geophys. Res. 71(2),367-373.
91. Kuhn, P. M., L. P. Stearns, and J. R. Stremkis, 1967: AtmosphericInfrared Radiation Over the Antarctic. ESSA Tech. Rept. ER55-IAS2, Boulder, Colo.
92. Gergen, J. L., 1956: "Black ball:" A device for measuring atmo-spheric infrared radiation. Rev. Sci. Instr. 27(7), 453-460.
93. Lucas, R. M., and G. H. Hall, 1960: The Measurement of High Alti-tude Balloon Gas Temperature. Tech. Rept. V, prepared for Officeof Naval Research by A. D. Little, Inc., Cambridge, Mass., 30 pp.
94. Dingwell, I. W., and R. Lucas, 1968: Recent Theoretical and Ex-perimental Studies of High Altitude Balloon Vertical Trajecto-ries. AIAA Paper 68-940, presented at AIAA 2nd AerodynamicDeceleration Systems Conference, El Centro, Calif., Sept. 1968.
95. Gabron, F., I. Dingwell, B. Allen, D. Comstock, 1968: A Study ofBalloon-Borne Instrumentation (Radiometers) to Detect ThermalRadiation Transients. NCAR Subcontract 84-68, prepared byA. D. Little, Inc., Cambridge, Mass., 63 pp.
96. Ney, E. P., R. W. Maas, and W. F. Huch, 1961: The measurement ofatmospheric temperature. J. Meteorol. 18, 60-80.
97. Hoerner, S. F., 1958: Fluid Dynamic Drag. (Published by author,148 Busteed Dr., Midland Park, N.J.)
132
98. Ostrach, S., 1972: Natural convection in enclosures,Advances in Heat Transfer 8, Academic Press, Inc., New York,N.Y., 161-226.