nec 4xi rev e - extron...config projector sw1: 1-2-3-4 sw2 sw3 sw4 sw5 sw6 prj cable comm as adapter...

Extron • System 4xixixixixi Switcher Series • User’s Manual • P/N 68-413-02 Rev. E

Configuration and ConnectionsNEC Installation

SYSTEM 4xixixixixiPROJECTOR COMMUNICATIONS KIT

ATTENTION!

PLEASE READ THIS DOCUMENT FOR IMPORTANTINSTALLATION INSTRUCTIONS

THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:

Kit Type: NEC

Included Communications Adapter(s):

Quantity Part Number Description1 26-472-01 ADP, UNV, “D”1 26-458-01 ADP, NEC MT1 26-494-01 ADP, UNV, “K”1 26-467-01 ADP, UNV, “A”

THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDINGCOMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUSMODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED ASINDICATED BY THE “✔ ” IN THE “CONFIG AS” COLUMN. IF YOUR PROJECTOR MODELDIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHERWITH THE CORRECT SETTINGS.

PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION ANDSIGNAL CONNECTION INSTRUCTIONS.

THIS SWITCHER HAS BEEN CONFIGURED FOR: NEC XG

CONFIG MODEL SW1 SW2 SW3 SW4 SW5 SW6 PROJ COMMAS 1 2 3 4 CABLE ADAPTER

✔ NEC XG off on on off 0 0 4 F 0 J9 26-472-01

NEC/Runco off on on off 0 0 7 5 0 J9 26-472-01

NEC MT Series off on off on 0 0 0 F 0 J15 26-458-01

NEC GT 2000 off on off on 0 0 4 E 0 J15 26-494-01

NEC host comm* off on off on 0 0 5 E 0 J15 26-467-01

NEC GT 1150 off on off on 0 0 5 E 0 J15 26-467-01

* As of printing: MT1045/1040, XT5000, VT440/540


NEC Installation Configuration and Connections

(Note: Information depends onSystem 4xi setup.)

(See note.)

(See note.)

(See note.)

(See note.)

[System 4xi model and softwareversion displayed here]

}

SW1

ON

SW2

SW4

SW3 SW5

J9

34 12

Connecting System 4xixixixixi to NEC/Runco or NEC XG Projector

If the System 4xi is already configured for an NEC/Runco or NEC XG projector,go to step 4. If it is not set up correctly, it will be necessary to change switchsettings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify thecorrect configuration.

1. Use the Front Panel to display the Information Menu to verify that the System 4xiis already set up for the NEC/Runco or NEC XG projector. Apply power to theSystem 4xi and do the following:

a. Press to display the MENU SELECT on the LCD screen.

b. Press or to step to Menu 8.

c. Press to select this menu.

d. Press or to display the configuration. The example to the left is general,yours will show the System 4xi model name, the software version and thefollowing information:PRJ = NEC (or NEC_XG for XG model)PRJ BAUD = 9600UNIT No. = 000HST BAUD = 9600 (value depends upon setup Menu 3)

2. Go to the procedure on page 2-3 to remove the System 4xi cover and then go topage 2-4 to set up the Main Controller board. Return to Step 3 (below) when theconfiguration is correct.

Config Projector SW1: 1-2-3-4 SW2 SW3 SW4 SW5 SW6 Prj Cable Commas Adapter

NEC/Runco off-on-on-off 0 0 7 5 0 J9 26-472-01

✔ NEC XG off-on-on-off 0 0 4 F 0 J9 26-472-01

System 4xi to NEC/Runco Configuration System 4xi to NEC XG Configuration

3. Double-check your work and be sure the System 4xi cover is on securely.

4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.

__________ Changes in some switch configurations are not detected until the power isremoved at the AC cord, and then restored.If the Projector Cable is wrongly connected to J15 on the Main Controller Board,Menu 8 will not indicate the error.

Use the appropriate cable diagram on page 6 and continue.

5. The NEC Adapter (NC COM) has two male connectors, one 9-pin and one15-pin. Plug the 15-pin male connector to the female connector marked“Remote 1” on the NEC connector panel.

SW1

ON

SW2

SW4

SW3 SW5

J9

34 12



6. Plug the 15-pin HD connector of the Projector Communications Extension cable(shown as CC 50') into the PJ Comm port on the System 4xi. The other end hasa 9-pin female connector. Plug this into the other 9-pin male D connector on theNC COM adapter.

______ Secure all of the connector screws.

7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HVcable onto the System 4xi output and those on the other end onto the matchingBNCs on the NEC connector panel. See cable diagram.

8. Power up the projector and set the projector as follows:

• if your system has less than 10 inputs, set the projector to SW_Level 1 mode

• if your system has 10 or more inputs, set the projector to SW_Level 2 mode

9. Apply AC power to the System 4xi.

____________ For the NEC XG: always apply AC power to the projector and place it in Stand-

NEC Memory Assignments

by power before applying AC power to the System 4xi. This procedure must be followed anytime AC power to the system has been interrupted or the CC cable detached. Failure to follow this AC power up sequence will causecommunication errors.

The following two examples and accompanying tables provide information for setting up the NEC projector (not the System 4xi). Please refer to the projector documentation for further details.

The table on the right lists the Extron channel assignments and the corresponding NEC host and peripheral slotassignments using Extron System Switchers.

The physical location of the Extron channelassignments will depend on the systemsetup.

The tables and charts in the examples belowillustrate System Switcher channelassignments for NEC models PG, PG+, PGXand XG.

__________ System 4xi can support a maximum of 22channels: 1 System 4xi (host) looped to multiple System 10 Switchers (peripherals).

EXTRONCHANNELNUMBER

NEC SLOTASSIGNMENT:

HOST

NEC SLOTASSIGNMENT:PERIPHERALS

1234567891011121314

M01M01M01M01M01M01M01M01M01M01M02M02M02M02M02M02M02M02M02M02M03M03M03

151617181920212223

S01S02S03S04S05S06S07S08S09S10S01S02S03S04S05S06S07S08S09S10S01S02S03

96 M10 S06979899100

M10M10M10M10

S07S08S09S10



Example 1: System 4xi with SW4 ARMX or SW6 ARMX Switcher

and Projector in SW_LEVEL 1 Mode

M01M02M03M04M05M06M07M08M09M10

NEC SLOTASSIGNMENT(SW_LEVEL 1)

EXTRONCHANNELNUMBER

NEC SLOTASSIGNMENT: Host

(4) 5 6 7 8 9

(M04) M05 M06 M07 M08 M09

NEC SLOTASSIGNMENT:Per iphera ls

N/A N/A N/A N/A N/A N/A

{*channels 8 and 9 available to SW6 ARMX only

(looped)

EXTRONCHANNELNUMBER


1 2 3 4

M01 M02 M03 M04

EXTRON SYSTEM 4 (Host)

NEC SLOTASSIGNMENT:

Peripherals

EXTREXTRON ON SW4 ARMX or SW6 (Peripherals

N/A N/A N/A



Example 2: System 4xi with Multiple System 10 Plus* Switcher peripherals and Projector in

SW_LEVEL 2 Mode

* System 8 Plus could also be used as a peripheral

Projector Input Channel List

The NEC projector channel input numberscorrespond to the System 4xi input numbers. Withthe projector's remote, press Operate, 4 (InputSelect). The Input Select information will display.Selecting an input number (left column) will tell theSystem 4xi to switch to the corresponding inputchannel.

Channel List Display for an NEC Projector

System 4xixixixixi - NEC/Runco and NEC XG Projector ConnectionsUse the following diagrams as a guide when connecting the System 4xi to anNEC/Runco or NEC XG projector. Refer to NEC/Runco or NEC XGdocumentation to continue the installation.

EXTRONCHANNELNUMBER


(4) 5 6 7 8 9 10 11 12 13

(M01) M01 M01 M01 M01 M01 M01 M02 M02 M02

EXTRON SYSTEM 10 (Peripheral 1)

NEC SLOTASSIGNMENT:

Peripheral(S04) S05 S06 S07 S08 S09 S10 S01 S02 S03

EXTRONCHANNELNUMBER


1 2 3 4

M01 M01 M01

EXTRON SYSTEM 4 (Host)

NEC SLOTASSIGNMENT:

PeriperalS01 S02 S03 S04

(looped)

M01

EXTRONCHANNELNUMBER


(13) 14 15 16 17 18 19 20 21 22

(M02) M02 M02 M02 M02 M02 M02 M02 M03 M03

EXTRON SYSTEM 10 (Peripheral 2)

NEC SLOTASSIGNMENT:

Peripheral(S03) S04 S05 S06 S07 S08 S09 S10 S01 S02

(looped)

NEC SLOTASSIGNMENT(SW_LEVEL 2)Host

M01M02M03M04M05M06M07M08M09M10

S01S02S03S04S05S06S07S08S09S10

Peripheral

Operate

No01020304050607080910

NameNTSC 3.58NTSC 4.43PALSECAMVGA480

Date06/29/9506/29/9506/29/9506/29/9506/29/95

InputVideoVideoVideoVideoRGB

4 (Input List)



CC 50'

H/V

R G B

3,4 or 5 BNC

15-Pin

1 2 3 4

ACAT Out R(Video) G(Y) B(C) VH/HV S-Video Remote 1 Remote 2Video OptionOut In

On/Off Input Select Enter

MultiSync XG135

NEC Projector

15-Pin

AdapterNC COMD

D26-472-01

9-Pin

Female

Male

Male

Male5

7

6

H/V

R G B

15-Pin

1 2 3 4

Male

AdapterNC COM26-311-01

15-Pin HD

9-Pin

CC 50'

VideoS-VideoOption 1Remote1

Remote 2

NEC/Runco Projector

R G B VHV

3, 4 or 5 BNC

AC InputPower

5

76

Female

Male

Male

Connecting the System 4xixixixixi to an NEC XG 135 Projector

Connecting the System 4xi xi xi xi xi to an NEC/Runco Projector

____________ In a rack mount, do NOT allow the weight of the cables to be supported by theSystem 4xi. See page 2-5 for cabling guidelines.




(See note.)

(See note.)

(See note.)

(See note.)


Connecting System 4xixixixixi to NEC MT Series Projector

If the System 4xi is already configured for an NEC MT Series projector, go tostep 4. If it is not set up correctly, it will be necessary to change switch settingson the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correctconfiguration.

1. Use the Front Panel to display the Information Menu to verify that the System 4xiis already set up for the NEC MT Series projector. Apply power to the System 4xiand do the following:




d. Press or to display the configuration. The example to the left is general,yours will show the System 4xi model name, the software version and thefollowing information:PRJ = NEC_MTPRJ BAUD = 9600UNIT No. = 000HST BAUD = 9600 (value depends upon setup Menu 3)



NEC MT Series off-on-on-off 0 0 0 F 0 J15 26-458-01




Use the following connection diagram and continue.

5. The NEC Adapter (NC COM) has two male connectors, one 9-pin and one15-pin. Plug the 15-pin male connector to the female connector marked“Remote 1” on the NEC connector panel.

}

SW1

ON

SW2

SW4

SW3 SW5

J15

34 12



System 4xixixixixi - NEC MT Series Projector ConnectionsUse the diagram below as a guide when connecting the System 4xi to the NECMT Series Projector. Refer to NEC documentation to continue the installation.

Connecting the System 4xixixixixi to the NEC MT-1000 Projector


__________ System 4xi channel numbers correspond to the projector’s “Group” numbers.

6. Plug the 15-pin HD connector of the Projector Communications Extension cable(shown as CC 50') into the PJ Comm port on the System 4xi. The other end hasa 9-pin female connector. Plug this into the other 9-pin male D connector on theNEC COM adapter.







RGBHV 5 BNC

15-PinMale

9-Pin Male

NEC-LCDAdapter

26-458-01

9-Pin Female

SY-VGA26-173-01

15-Pin Male

OUTPUT

PJ COMM

RS 232

AUDIO AUDIO AUDIO AUDIO AUDIOH/HV

R/C G/Y BR/C G/Y B

V

INPUT 4

H/HV V

R/C G/Y B

INPUT 3

H/HV V

R/C G/Y B

INPUT 2

H/HV V

R/C G/Y B

INPUT 1

H/HV V




(See note.)

(See note.)

(See note.)

(See note.)


Connecting System 4xixixixixi to NEC GT 2000 (or equivalent) Projector

If the System 4xi is already configured for an NEC GT 2000 projector, go to step4. If it is not set up correctly, it will be necessary to change switch settings on theSystem 4xi ’s Main Controller Board. Begin at Step 1 to verify the correctconfiguration.

1. Use the Front Panel to display the Information Menu to verify that the System 4xiis already set up for the NEC GT 2000 projector. Apply power to the System 4xiand do the following:




d. Press or to display the configuration. The example to the left is general,yours will show the System 4xi model name, the software version and thefollowing information:PRJ = NEC_GTPRJ BAUD = 9600UNIT No. = 000HST BAUD = 9600 (value depends upon setup Menu 3)



NEC GT 2000 off-on-on-off 0 0 4 E 0 J15 26-494-01





}

SW1

ON

SW2

SW4

SW3 SW5

J15

34 12



5. The NEC Com Adapter (26-494-01) has two male connectors, one 9-pin and one15-pin. Plug the 15-pin male connector to the female connector marked“REMOTE 2/PC” on the NEC connector panel.

6. Plug the 15-pin HD connector of the Projector Communications Extension cable(shown as CC 50') into the PJ Comm port on the System 4xi. The other end hasa 9-pin female connector. Plug this into the other 9-pin male D connector on theNEC COM adapter.







System 4xixixixixi - NEC GT 2000 Projector ConnectionsUse the diagram below as a guide when connecting the System 4xi to the NECGT 2000 Projector. Refer to NEC documentation to continue the installation.

Connecting the System 4xi to the NEC GT 2000 Projector



RGBHV 5 BNC

15-PinMale

9-Pin Female

CC 50'

9-Pin Male

COM AdapterP/N 26-494-01 "K"

15-Pin Male

OUTPUT

PJ COMM

RS 232


R/C G/Y BR/C G/Y B

V

INPUT 4

H/HV V

R/C G/Y B

INPUT 3

H/HV V

R/C G/Y B

INPUT 2

H/HV V

R/C G/Y B

INPUT 1

H/HV V

○

○

○

○

○

○

○

○

○

○

○

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○

○




(See note.)

(See note.)

(See note.)

(See note.)


Connecting System 4xixixixixi to NEC XT 5000 (or equivalent) Projector

If the System 4xi is already configured for an NEC XT 5000 projector, go to step4. If it is not set up correctly, it will be necessary to change switch settings on theSystem 4xi ’s Main Controller Board. Begin at Step 1 to verify the correctconfiguration.

1. Use the Front Panel to display the Information Menu to verify that the System 4xiis already set up for the NEC XT 5000 projector. Apply power to the System 4xiand do the following:




d. Press or to display the configuration. The example to the left is general,yours will show the System 4xi model name, the software version and thefollowing information:PRJ = NEC 10XXPRJ BAUD = 38400UNIT No. = 000HST BAUD = 9600 (value depends upon setup Menu 3)



NEC XT 5000 (host control) off-on-on-off 0 0 5 E 0 J15 26-467-01





SW1

ON

SW2

SW4

SW3 SW5

J15

34 12

}



5. The NEC Com Adapter (26-467-01) has two male connectors, both 9-pin. Plugone end to the female connector marked “OPTION IN” on the NEC connectorpanel.

6. Plug the 15-pin HD connector of the Projector Communications Extension cable(shown as CC 50') into the PJ Comm port on the System 4xi. Plug the 9-pinfemale connector into the other 9-pin male D connector on the NEC COMadapter.







System 4xixixixixi - NEC XT 5000 Projector ConnectionsUse the diagram below as a guide when connecting the System 4xi to the NECXT 5000 Projector. Refer to NEC documentation to continue the installation.

Connecting the System 4xi to the NEC XT 5000 Projector



CC 50'

15-Pin HD

9-Pin

AdapterNC COM26-467-01

A

A

9-Pin

Male

Female

Male

Male

RGBHV 5 BNC

CC 50'

OUTPUT

PJ COMM

RS 232


R/C G/Y BR/C G/Y B

V

INPUT 4

H/HV V

R/C G/Y B

INPUT 3

H/HV V

R/C G/Y B

INPUT 2

H/HV V

R/C G/Y B

INPUT 1

H/HV V

nec 4xi rev e - extron...config projector sw1: 1-2-3-4 sw2 sw3 sw4 sw5 sw6 prj cable comm as adapter...

Documents