netcom th serial protocol data sheet

7/27/2019 Netcom Th Serial Protocol Data Sheet

http://slidepdf.com/reader/full/netcom-th-serial-protocol-data-sheet 1/3

SINET ICALink to the network

Extending the reach of yourNetwork Management System

Sinetica Corporation Ltd.Singleton Court

Wonastow Road Industrial EstateMonmouth. NP25 5JA

Tel: 01600 716400Fax: 01600 772026

Email: [email protected]: http://www.sinetica.co.uk VAT Reg. No. GB 542 8088 34Reg. No. 2623558

NetCom THDATA SHEETSerial ProtocolVersionSEC protocol V2.6Megatech protocolPhoenixtec protocol

NetCom TH is an Ethernet compatible network interface device that is intended to be used as aremote monitor of Uninterruptible Power Supplies (UPS) using SNMP. Additionally NetCom TH also

supports Web based communications and it is shipped with its own monitoring / managementsoftware tool.

NetCom TH can be attached any UPS that uses the standard UPS protocols listed above. TheNetCom TH allows a network supervisor to monitor the UPS via SNMP protocol (Simple NetworkManagement Protocol) over TCP/IP networks using popular network management platforms such asHP OpenView, SunNet Manager, Castle Rock SNMPc etc..

RFC1628NetCom TH complies with a worldwide standard SNMP MIB format (rfc1628) making it quick andeasy to install for NMS operators.







Tel: 01600 716400Fax: 01600 772026


Dimensions Layout and dimensions for the NetCom TH are shown in Figure 1.

Height = 30mm (without feet), 32mm (with feet)

Hardware Interface Description – Port 1

Pin # Name Description Input #

1 DCD Data Carrier Detect 3

2 RXD Receive 1

3 TXD Transmit4 DTR Data Terminal Ready

5 GND Ground

6 DSR Data Set Ready 5

7 RTS Request To Send

8 CTS Clear To Send 2

9 RI Ring Indicator 4

This port can be used to monitor up to 5 contact closure signals

Hardware Interface Description – Port 2 (unused)

Pin # Name Description Input #

1 DCD Data Carrier Detect 62 RXD Receive 7

3 TXD Transmit

4 DTR Data Terminal Ready

5 GND Ground

6 VCC +5v 5 volt drive for Analogue input

7 Analogue In Reserved

8 GND Ground

9 Analogue In Reserved

Port 1D9 RS232

Port 2D9 Temp/Humidity

5VDC Power Connector

10 Base TConnector

DIP switch

148.60 mm

90mm 41.25mm

Figure 1Power

LED

RS232

LED

NetworkLED

Status

LED







Tel: 01600 716400Fax: 01600 772026


OPERATING DATA

Communication SNMP monitoring / managementTelnet managementJAVA monitoring/management applet (“Viewer”)WEB managementTerminal configuration

RS232 Port RS2332 for local configuration and UPS communication

Security Telnet and WEB access password protection.

Upgradeability Firmware upgradeable using serial download or TFTP download.

Standards andCertifications

CE

PHYSICAL

Kit contents Unit, config cable, CD, mains adaptor PSU, carton

Enclosure Steel case with epoxy powder coating90mm wide x 149mm deep and 32mm high0.3 Kg weight

LED indicators DC Power OnStatusNetwork trafficRS-232

Power input 1 x jack plug +5v DC

Serial config port D9 male port 1

Temp/Humidity port D9 female port 2

Digital input port D9 male port 1 and D9 female port 2LAN port RJ45 way socket 10 BaseT

Normal power usage 300 mA

Maximum power 400 mA

Input protection Polyfuse

Operating range 0 ~ 40°C

Operating humidity 5 ~ 90%

Storage temperature -10 ~ 70°C

Storage humidity 5 ~ 100%

netcom th serial protocol data sheet

Documents