network camera - emstone · 3/13/2020 · this is a megapixel network camera which uses a...

NETWORK CAMERA

User Manual

Our all network cameras support the Profile S.

AMA-X310AMA-X300AMA-X500

Introduction

This is a megapixel network camera which uses a 1/2.8-inch megapixel progressive scan SONY CMOS sensor.Built-in H.264, MPEG4, MPEG CODEC and streaming server, the advantage of this camera allow you to monitor real time image from a remote location via internet. This camera supports both static IP and dynamic IP, and can change communication port, resulting in one IP address supporting multiple servers. It also supports CMS(Central Monitoring System), various services and features waterproof for outdoor use without extra device.

<Caution>Software, server and service may be changed according to policy or may

be stopped without prior notification.Appearance, function and specification may be changed without prior

notification. Our company assumes no responsibility for visible or invisible loss resulted from changes in policy or products.<경 고>software및 server 와 service는 정책 변경이나 기간 만료로 인하여 변경 되어 질수 있습니다.외관 혹은 제품 성능은 별도 통보 없이 변경되어질 수 있으며 폐사(당사)는 정책변경이나 제품변경으로 인한 유무형 손실에 대해서 책임을 지지 않습니다.<警告〉software及 server和service 因政策变化或到期可能被改变。外观，性能和功能可以在不事先通知而变动。我公司对政策变化或产品变更而造成的有无形损失不承担赔偿责任

Safety Cautions

1. This camera may be damaged by electrical and physical shock.2. Use regulated 12V DC, 1A power supply. 3. In case the unit fails, DO NOT try to disassemble the product.Contact or consult the distributor or an authorized technician for after-sales service. Warranty void for the product disassembled without an authorization from the distributor or an authorized technician.4. All responsibility by using this unit is on the user.5. In case it is installed at high location, be sure to mount securely to prevent the unit from falling below.

If the product is to be put out of operation definitively, take it to a local recycling plant for a disposal which is not harmful to the environment.

Please read the instruction carefully for correct use of the product and preserve it for reference purposes. This specification is subject to change without any prior notice to improve the quality.

HD NETWORK CAMERA User Manual

3

Contents

Camera Overview

Basic Configuration

5 Camera Features

5 Hardware Overview

13 Installation and connection

15 Log in

17 Live Video Check

18 Menu bar description

20 Network

22 Video Setting

23 System

Advanced Configuration

24 TCP/IP

25 RTSP

26 DDNS

27 HTTP

28 Onvif

Camera 29 Video

30 Video Mode

31 Audio

32 Day / Night

33 OSD

35 Privacy Zone

35 Image Adjustment

36 White Balance

37 WDR

38 DNR

Network

4

Contents

Camera 39 Exposure

40 Defog

41 PTZ

System 42 Camera name

43 Language

44 Date / Time

45 User management

46 Update

47 Reset / Restart

Event

48 Alarm

49 Motion Detection

Event

50 Record

51 SD memory

Record

IP manager

52 Run IP manager

53 Find IP address

54 Change IP address

55 Update

Use IP manager

5

Camera Overview

Camera Features

AMA-X300 series, AMA-X500 series

Progressive Scan Sensor

Sony Sensor provides color with extremely clear and vivid excellent

image quality.

D-WDR(Digital Wide Dynamic Range)

It combines bright area with low shutter speed exposure into one

composite image in order to get details from dark and bright combination

image without any saturation.

3 DNR(Digital Noise Reduction)

It is much more effective as removing picture noise caused by objects in

motion under the low light condition.

Web Server built-in

Motion Detection

When user is simultaneously monitoring at the same time, the camera detects

movement motion of any objects on the screen and transmits alert signal into

the external alarm to have user’s attention on the screen.

Two-way audio support

Triple codec(H.264, Mpeg4, MJPEG) _ AMA-x300 series

Quad codec(H.264, Mpeg4, MJPEG) _ AMA-x500 series

ONVIF Compliance

Our all network cameras support the Profile S.

2 megapixel Supreme resolution Image (1920 x 1080) – AMA-X300 series

2 Megapixels with a resolution of 1920 x 1080. This is almost 6X better than

an VGA image of 640 x 480 as found on some IP cameras.

2, 3 and 5megapixel Supreme resolution Image – AMA-X500 series

The Camera using Sony provides color with extremely clear and vivid excellent

image quality under the low illumination environment.

Common Features

6

Camera Overview – AMA-23X0 Series

Hardware overview

Product Picture

AMA-2300 42mm x 42mm sized


Hardware overview

Camera Specification

7

Category Description

Image

Image Sensor Sony Exmor 2.07Mega Pixels Image Sensor

Size 1/2.9 inch

Scan System Progressive Scan

Total Pixels 2000(H) x 1121(V), 2.24 Mega Pixels

Effective Pixels 1984(H) x 1105(V), 2.19 Mega Pixels

Function

Day & Night Auto / Day(Color) / Night(BW), ICR Control

Privacy Area On / Off (6 Programmable Zones)

Motion Detection 48 Zone, Sensitivity 1 ~ 5 Step, On / Off

L P R Auto, 1/15 ~ 1/9000, On / Off

W D R BLC / DWDR(1 ~ 5 Step) On / Off

3 D N R Digital Noise Reduction, 1 ~ 63 Step

Elec. ShutterAuto(1/15~1/15000), Suppress Rolling, Man

ual

Color adjust Bright / Contrast / Saturation / Sharp / Hue

White BalanceAuto / Push/ Indoor / Outdoor / Fluoresce

nt / User

OSD display Text, Data, Time, Event, On / Off

Image Mirror Normal / mirror(H) / Flip(V) / Both(HV)

Ext. Video VBS 1.0Vp-p

ElectricalPower Supply DC12[V] ±10%

Current Max 230[mA]

Environmental

Operating Temp. 0℃ ~ +50℃

Preservation Temp. -10℃ ~ +60℃

Humidity 0% ~ 90%

Physical Spec

Dimension.42mm(W) X 42mm(H) X 9.5mm(D), without

holder

Weight. 70g

Lens holder Option

Camera Overview – AMA-23X0 Series

8

Camera Overview – AMA-X500 Series

Hardware overview

Product Picture


Hardware overview

Camera Specification _ AMA-2500(2MP)

9


Image

Image Sensor Sony Starvis 2.07Mega Pixels Image Sensor

Size 1/2.8 inch




Function




L P R Auto, 1/15 ~ 1/9000, On / Off

W D R DWDR(1 ~ 3 Step) On / Off

D N R 2DNR, 3DNR

Defog detects foggy, On / Off

S L D C Simple_Lens Distortion Correction, On / Off

H L C On / Off

Elec. Shutter Auto(1/15~1/15000), Suppress Rolling, Manual


White BalanceAuto / Push/ Indoor / Outdoor / Fluorescent /

User

OSD display Text, Date, Time, Event, On / Off

Image Mirror Normal / mirror(H) / Flip(V) / Both(HV)/Rotate


Current Max 220[mA]

Environmental



Humidity 0% ~ 90%

Physical Spec


holder

Weight. 40g

Lens holder Option


Hardware overview


10


Image


Size 1/2.8 inch




Function




L P R Auto, 1/15 ~ 1/9000, On / Off


D N R 2DNR, 3DNR



H L C On / Off




User




Current Max 220[mA]

Environmental



Humidity 0% ~ 90%

Physical Spec


holder

Weight. 40g

Lens holder Option


Hardware overview


11


Image


Size 1/1.8 inch




Function




L P R Auto, 1/15 ~ 1/9000, On / Off


D N R 2DNR, 3DNR



H L C On / Off




User




Current Max 220[mA]

Environmental



Humidity 0% ~ 90%

Physical Spec


holder

Weight. 40g

Lens holder Option


Hardware overview

Network Specification

12

Camera Overview


System OS Embedded Linux

Network

Interface RJ45 10/100 Base-T PoE

ProtocolTCP/IP,UDP/IP,RTP,RTSP,RTCP,NTP,HTTP,DHCP,FTP,SMTP,DNS,DDNS

Onvif ver2.4.2

DDNS iplinker.net

Simultaneous Access Max. 10 user

Video

Compress Format H.264/MPEG4/MJPEG

Resolution

1920x1080/1280×1024/1280×960/128

0×720

/1024×768/640×480/320×240

Max. Frame Rate 30fps @all resolution

Video QualityH.264,MPEG4 : Bitrate Control

MJPEG : Quality Level Control

StreamingTriple Stream (Stream1,2,3)

RTP/RTSP, UnicastRTP, Multicast RTP

AudioCompress Format G.711 u-law

Streaming Two way

EventSensor In 1 ( NC / NO )

Alarm Out 1 (Digital Output, Open Collector)

Web

Browser

OS Windows XP, 7, 8, 10,

Manager IE 11이상, Firefox, Safari, Opera

Viewer IE only (Active-X)

13

Camera Overview

Installation and Connection

Installation

On the assumption that User PC and the camera are used under static IP, and the camera is to

be directly connected with User PC or Local Network, The installation procedure is to be;

(1) Connect the camera and PC with LAN cable(Direct cable or cross cable).

(Please use the direct cable if you connect to local network)

(2) Power on camera.

* Using regulated 12V DC 500㎃(No IR LED model) or 1A (Built-in IR LED model)

* Using PoE(Power Over Ethernet) : This camera adopted PoE that supplies power in addition

to data sending and receiving using LAN cable without separate power connection and it

provides convenience for users at installation. When you connect the camera with PoE and DC

adaptor, only PoE is used.

(3) Wait about 2 minute after on camera, the system will be booted.

Alarm in wiring diagram

To connect the external sensor

Connect one sensor(Alarm) line(Yellow) of the sensor to the Alarm in port

and connect the Alarm out(White) line and 12V DC line(Red) to the Alarm out device.

Alarm In Alarm Out

Max. 100mA open collector

14

IP search

Chang the setting value of PC network environment

Basic network setting value of the unit is to be;

IP Address : 192.168.1.30Subnet Mask : 255.255.255.0Gateway : 192.168.1.1

To connect the unit in user's PC, change the setting value of PC network environment.

Set IP Address, Subnet Mask and Gate-way of user's PC with 192.168.1.50 /

255.255.255.0 / 192.168.1.1 as shown below picture.

[Caution] Before changing the setting value, please memorize the previous setting valueon your PC.

15

Log in

Connect the Camera with web browser

(1) Run web browser.

(2) Input 192.168.1.30 (default value) in URL and press "ENTER" button.

(3) And then, below picture is to be shown.

See the video

As you see the above picture, the login window appears.

Enter the User ID and Password then click to “LOGIN” to access the Camera.

User’s authority to see the video feed is as follow.

I D Password Authority Detail

admin admin AllStream,

Web management

root root All Stream

guest guest View only Stream

[Caution] You must change default value of ID/Password into new ones after installation

16

Log in

Run web browser and input http://192.168.1.30(default value) in URL and

press "ENTER" button then below picture will be shown.

Administration page log-in

Input ID and password and click on “Log in” to setup page

ID Password Authorityadmin admin Allroot root Allguest guest View only

If you logged in first in administrator mode, please change the password and ID of administrator.

Setup page

After logged in, firstly you can see

the camera setup page.

Press “Live” button to go to

Live view page.

17

Live - Video Check

Active-X auto installation

If connecting to a camera for the first time, you will see the installation message.

Click "install" on the security certificate to load the Active-X control.

If you choose "Don't install", the web viewer would not work.

Click “Retry” to display

the webpage again.

Click “Install” to begin installation of the Active-X.

18

Live - Video Check

Installation Complete

After finished the installation, Web Viewer appears and image of camera is to be seen.

19

Menu bar description

Item Configuration

Stream Selection Select stream codec and resolution menu related to live-view was defined only by the admin.(H.264/MPEG/MJPEG)

Stream ConnectionConnect to the stream

Stream DisconnectionDisconnect to the stream

Record Saves the stream as a moving picture file in the .aviformat

CaptureSaves the snapshot as an image file in the .bmp format

File PathSpecify the file saving path

Full screenExtend the screen

PC speaker(Option)You can turn on or turn off the speaker of PC

PC mic. (Option)You can turn on or turn off the mic. of PC

Zoom and Focus(Option) Control the zoom and Focus of MFZ lens

MFZ Speed control Control the speed of MFZ lens

One push One time Auto Focus

Live - Video Check

20

Setup – Basic Configuration (Network)

Network settings

Change the device IP address to the same subnet with your computer by either modifying

The IP address manually or checking the checkbox of enable DHCP.

Input the IP Add. , subnet mask

and gateway then press save

Button to activate your

IP address modification .

Basic configuration - Network

You can set the TCP/IP and port of the camera here.

21

Setup – Basic Configuration (Network)

Set port mapping.

Change the port according to router environment. Please check router or call the router manufacture

For help with port setting

Default HTTP port is 80 / RTSP port 554

Click save to save the settings

22

Setup – Basic Configuration (Video)

Video Setting

Change the Stream type of the camera.

Our camera supports third stream, The Main stream for recording and Live view on the NVR or CMS,

And the sub streams can be used for multi channel view on the NVR or CMS.

User can be changed that parameters according to user environment.

Resolution

Set the video size.

Video Encode

Set the Codec. This camera supports 3 kinds of codec simultaneously.(H.264, MPEG4, MJPEG)

Video Profile Main Profile and High Profile for coding are selectable.

Bit rate Set the Bit rate to 128 ~ 8192kbps.

Bit rate type Choose a bitrate type(constant(CBR) or Variable(VBR))

Key Frame interval Set the frame interval to 1 ~ 60 fps

URL RTSP address


23

Setup – Basic Configuration (System)

System

Upgrading the system.

Import or Export configuration file, which can simplify the configuration steps

when there are a lot of cameras needing configuring.

Restore the default settings.

Update

Click Browse to select the local upgrade file and then click Upgrade to start

remote upgrade..

Import or Export camera

Select the exported configuration file, and then click “Import” to start importing configuration file.

Factory Default

Restore the default settings.

Reboot

Reboot the camera.


24

Setup – Advanced Configuration (Network)

Network – TCP/IP

Change the device IP address to the same subnet with your computer by either modifying

The IP address manually or checking the checkbox of enable DHCP.

.

Mac Address

Mac address of Camera.

IP address setting

Input the IP Add. , subnet mask and gateway then press save Button to activate your

IP address modification .

DNS Server Setting - For setting of DNS server, input DNS address to fit with network

environment to set(Default address is DNS address of 'Dacom', 'Hanaro telecom').

Use DNS value normally set in PC. DNS address should be necessarily input.

Click “save” button to save setting value.


25


Network – RTSP

This camera provides the RTSP/RTP stream transmission as well as TCP/IP stream.

The function is based on VLC(http://www.videolan.org/) media player.

If duplicated port used in this function with the port used from other process, it will not be working well.

RTSP Port : Setting of RTSP port.(default port: TCP 554)

RTSP Time out enable

If the server do not receive the RTCP from Client then RTSP session will be stopped

RTSP authentication : To set using for user authority on RTSP session

Use MULTICAST: Multicast function transfers the data to multiple users by a single streaming transfer.

It loaded less traffic in the network than unicast. There should, however,

be multi-casting functions in all network equipment which is in located in between

streaming server(camera) and clients.


26


Network – DDNS

DDNS is an abbreviation of Dynamic Domain Name Service that converts the IP address of

a camera into a general Host Name so that the user can easily remember it.

1) Click [Enable].

2) Enter the domain name(over 4 characters) and email address.

3) Perform the duplicate check for the domain that you entered by clicking [Check].

4) Click [Register], then you should make sure whether the Status is ‘Register OK’ or not.

5) Click [Unregister] to delete registered domain name.


27


Network – HTTP

This function transfer the stream by using Server Push method and can use the control function

by CGI calls.(EX. Port I/O control)

Good point of this function is using web port , so it is able to transfer the stream and control

which is not affected by fire wall.


28


Network – Onvif

Our all cameras support Onvif profile S


29

Setup – Advanced Configuration (Video)

Camera - Video

Change the Stream type of the camera.

Our camera supports third stream, The Main stream for recording and Live view on the NVR or CMS,

And the sub streams can be used for multi channel view on the NVR or CMS.

User can be changed that parameters according to user environment.

Resolution

Set the video size.

Video Encode

Set the Codec. This camera supports 3 kinds of codec simultaneously.(H.264, MPEG4, MJPEG)

Video Profile Main Profile and High Profile for coding are selectable.

Bit rate Set the Bit rate to 128 ~ 8192kbps.

Bit rate type Choose a bitrate type(constant(CBR) or Variable(VBR))

Key Frame interval Set the frame interval to 1 ~ 60 fps

URL RTSP address


30

Setup – Advanced Configuration (Video Mode)

Camera – Video Mode

Setting the Mirror, Rotate and TV type

Image mirror

Select a video source mode(Normal, Flip, Mirror, Both)

Rotate

Rotate the video image to 90˚ or 270 ˚ .

TV type

Select TV type(NTSC and PAL)


31

Setup – Advanced Configuration (Audio)

Camera – Audio

You can configure the I/O settings of the audio source from the camera.


32

Setup – Advanced Configuration (Day / Night)

Camera – Day / Night

This menu is to set IR Cut filter, IR LED On/Off, Color and B/W mode.


Day : The picture is always displayed in Color(using IR cut filter).

Night : The picture is always displayed in B/W(Don't use IR cut filter).

Auto : Automatic day(Color) & night(B/W) switching by setting value.

Please set the value properly according to the environment.

Time : This menu is to set change the Day and night mode by time.

Activate IR LEDs : Checked this menu, IR LEDs turn off or on according to Day or Night mode.

If not checked it, IR LEDs are always off.

33

Setup – Advanced Configuration (OSD)

Camera – OSD

Configure the settings as necessary of OSD in stream.


34

Setup – Advanced Configuration (Privacy Zone)

Camera – Privacy Zone

Configure the settings as necessary of OSD in stream.


Check the ‘Enable’ to activate the function. ‘Show’ is to specify the privacy zone.

* You can specify up to 4 zones.

35

Setup – Advanced Configuration (Image Adjustment)

Camera – Image Adjustment

You can change the camera color settings according to the environment where the camera is located.


Brightness describes bright of the image, which ranges from 1~100, and the default

value is 50.

Contrast describes the contrast of the image, which ranges from 1~100, and the

default value is 50.

Saturation describes the colorfulness of the image color, which ranges from 1~100,

and the default value is 50.

Sharpness describes the edge contrast of the image, which ranges from 1~100, and the

default value is 50..

36

Setup – Advanced Configuration (White Balance)

Camera – White Balance

You can change the camera white balance settings according to the environment where

the camera is located.


Auto : Adjust white balance automatically.

Indoor : Adjust white balance to indoor environment(3200˚K).

Outdoor : Adjust white balance to outdoor environment(5600˚K).

Fluorescent : Adjust white balance to fluorescent environment(4000˚K).

User : User can adjust the red and blue gains of the camera video manually.

37

Setup – Advanced Configuration (WDR)

Camera – WDR

It displays a sharp image of the objects in a scene where both bright and dark areas exist.


38

Setup – Advanced Configuration (DNR)

Camera – DNR

DNR reduces the noise in the video stream. Disable, 2DNR Mode and 3DNR

Mode are selectable


39

Setup – Advanced Configuration (Exposure)

Camera – Exposure

If the camera is equipped with the fixed lens, only Manual is selectable, and the iris

mode is not configurable.

If Auto is selected, you can set the auto iris level from 0~ 100.


40

Setup – Advanced Configuration (Defog)

Camera – Defog

You can enable the defog function when the environment is foggy and

the image is misty. It enhances the subtle details so that the image appears clearer.


41

Setup – Advanced Configuration (PTZ)

Camera – PTZ

You can control the lens(Focus and Zoom).


One push : one time auto focus.

Lens Reset : Use it when the image blur caused by defocus of the lens.

42

Setup – Advanced Configuration (Camera name)

System – Camera name

Camera title would be shown on the top of the video when you see the video by the viewer.


Server title is to be English without space(Max. 10 characters).

43

Setup – Advanced Configuration (Language)

System – Language

This is to select language to be displayed in all web pages such as Administrator's page, web viewer

and main page.


You can select the language as English, Korean and Japanese.

44

Setup – Advanced Configuration (Date / Time)

System – Date / Time

There are two ways of time setting as follow


Auto(NTP) : This is to set up local time in case of monitoring from different time zone area.

Select one of time zone in 'Time Zone' and save.

Manual : This is for user to set up time directly. There can be some gaps between local and

time of the unit.

45

Setup – Advanced Configuration (User management)

System – User management

This is to register an account of user who monitors and controls video.

Administrator's ID and password should be English, within 15 characters, without space.

A maximum user to allow registration is 20 persons.

Click ‘Delete’ for deleting user.

46

Setup – Advanced Configuration (Update)

System – Update

You can update the camera firmware and ONVIF firmware as below site.

47

Setup – Advanced Configuration (Reset / Restart)

System – Reset / Restart

This is the function to restart the camera system.

48

Event – Alarm

Event – Alarm

This is the function to restart the camera system.

Alarm Input - Type

Select Normal Close(NC) or Normal Open(NO).

Circuit of N/O type is usually open, and the activation of the sensor occurs at the time of

close, and N/C type works reverse way.

Alarm Output

Alarm input : Alarm output function operates only by alarm input event.

Motion : Alarm output function operates only by motion event.

Duration Time

Set duration time upon alarm events.

49

Event – Motion Detection

Event – Motion Detection

Enable : To use motion detection function, check ‘Use Motion Detection’.

Sensitivity Level : Setting up sensitivity to detect motion to adjust input video by situation.

You can select 1~5, and 5 is the highest


50

Event – Record

Event – Record

You can configure the event recording settings so that you can transfer the images stored in the camera

to the SD memory if an event(motion or alarm input) occurs.


51

Event – SD Memory

Event – SD Memory

You can configure the event recording settings so that you can transfer the images stored in the camera

to the SD memory if an event(motion or alarm input) occurs.

1. Check “Use SD Memory” then click “Save”

2. Push the “Mount” button, Capacity of SD card will be shown.

52

IP Manager – Use IP manager

Use of IP Manager

This program is the utility to find out the unit connected to local network. It is useful for the

application of the unit connected by DHCP function.

It can provide you the information such as IP address, MAC, web port for easy installation and use.

Run IP Manager program

Double click "IP Manager" file to open the program.

① Select all units of the list② Deselect all units③ Delete the list④ Resize the window.⑤ Scans for cameras that are currently connected to the network⑥ Consecutive number of the list ⑦ MAC information of the unit⑧ IP address of the unit⑨ Subnet mask⑩ Gateway information of the unit⑪ IP type of the unit(Static IP/Dynamic IP⑫ Web port number to connect⑬ Stream port number⑭ The cameras that are currently connected to the network ⑮ To change the information

53

IP Manager – Find IP address and Change IP address

Find IP address

Click “Find” button to find the cameras that are currently connected to the local network.

Below picture will be shown, after IP finding completed.

Click mouse right button to open sub menu as like above image.Open web page : connect the camera web page.IP change : change the IP address

Change IP address

After finding IP address, if you want to change IP address, Gateway or Subnet Mask,

double click IP address you want to change or check the list on the “index” and click “Change”.

54

IP Manager – Change IP address

Change IP address for one unit

Static IP

Double click IP address you want to change or check the list on the index and click “Change”.

Dynamic IP

• Double click IP address you want to change or check the list on the index and click “Change”.

• Check the “Dynamic IP Address”, the IP Address, Subnet Mask, Default Gateway, Web Port,

Stream port will be grayed out.

• Input ID and password.

• Click the “Change” button. After a while, setup will be completed. And you can find

the changed information.

• Check the “Static IP Address”, input the information

( IP Address, Subnet Mask, Default Gateway, Web

Port, Stream port) you want to change.


• Click the “Change” button. After a while, setup will

be completed.

• Click the “Find” button one more time to check the

changed information.

55

IP Manager – Change IP address

Change IP address for multiple units

Static IP

Check the index box of two or more units you want to change. Click the “Change” button.

The picture of next page will be shown.

Click the “Batch” button, the dialog appears.

• Check the “Static IP Address”, input the information

(IP Address, Subnet Mask, Default Gateway, Web Port,

Stream port) you want to change.

• Input the “Last Address” and “step”.

EX) If the condition sets like the picture 5-5, the last

number of the IP address will be increased each 1,

starting 30 and will not over 253.

• Input ID and password, and click the “Save” button.

• After a while, the changed IP address dialog appears.

• Click the “Change” button. After a while, setup will be completed.

• Click the “Find” button one more time to check the changed information.

56

IP Manager – Update

Dynamic IP

• Double click IP address you want to change or check the list on the index and click “Change”.

• Click the “Batch” button, the dialog appears.

• Check the “Dynamic IP Address”, the IP Address, Subnet Mask, Default Gateway, Web Port, and

Stream port will be grayed out.


• Click the “Change” button. After a while, setup will be completed. And you can find the changed

information.

Update

Update the firmware to camera using IP manager.

• Click ‘Find’ button to find the cameras.

• Check the check box of the camera then click ‘Update’ button.

• The picture of next page will be shown.

* Before update the F/W, IP of each camera should be different.

57

IP Manager – Update

Choose the F/W

Choose the firmware to update the camera and Reboot.

• Click ‘Authentication’ button to input the ID and Password.

Default ID and password is ‘admin / admin’

* If each camera’s ID and Password is not same, you can not update together.

• Click ‘Update’ button to choose Firmware.

• The picture of next page will be shown.

• Choose the Firmware such as camera F/W, ONVIF and Active-X.

User can update the all F/W at once.

• Click ‘OK’ button to Update the Firmware for a while.

• After finish the update, user should reboot the cameras. Please click the ‘Reboot’ button to

Reboot camera.

network camera - emstone · 3/13/2020 · this is a megapixel network camera which uses a...

Documents