• Some cameras may display black lines at the end on the image due to the gap of the display area. Adjust the picture position (see page 67 of the Operating Instructions on the Setup CD-ROM).

• To ensure that the most current image is displayed, Internet Explorer should be configured as follows. This will not have a negative effect on normal use.

1. While viewing any website, click [Tools] [Internet Options].

2. In the section "Temporary Internet Files", click [Settings] and check [Every visit to the page].

• If the Security Warning window is displayed when installing ActiveX®

Controls, click [Yes].• To install ActiveX Controls on Microsoft® Windows® XP Service Pack

2, see "Security Warning window on Microsoft Windows XP Service Pack 2" on the last page.

Notes

Click [Next] to set up the Internet access to this product and go to step in "Set up Internet access to this product." on the next page.

Click [Automatic Setup (Local Access Only)].

Enter the user name and password, and click [Save].

Enter the user name and password that were set, and click [OK].

When the Single Camera page is displayed, setup is completed.

• Click [Cancel] to finish setup.

Important

• If the Windows Security Alert is displayed, click [Unblock].

• If the indicator does not light green, check the connection. (see page 10 of the Operating Instructions on the Setup CD-ROM).

• If more than 20 minutes have passed since this product was turned on, this product cannot be set up from the Setup Program. Disconnect the AC cord from the outlet, and reconnect it again, and restart the Setup Program.

• The Setup Program may not list this product due to your firewall or antivirus software settings on your PC. If you cannot disable your firewall or antivirus software, you can set up this product by entering this product MAC address on the following window. The product's MAC address can be found on the label affixed to the bottom of each product. See page 11 of the Operating Instructions on the Setup CD-ROM for details.

• The MAC Address on the bottom (see page 11 of the Operating Instructions on the Setup CD-ROM.) of this product shows which product you select on the List window.

• This program searches for this product that are connected to the router and displays their MAC Addresses, IP addresses and Port Numbers.

Notes

Displays the manuals.If your PC does not have Adobe® Acrobat® Reader®, install it from the Adobe Reader website.

Closes the Setup Program.

Displays version information about this program.

Sets up this product or the camera.

Installs Network Camera Recorder trial version.

List window

Displays IPv4 or IPv6 information.

StatusPort No.

MAC Address

IP Address

Insert the Setup CD-ROM into the CD-ROM drive of the PC.(If the Network Camera Setup window is not displayed automatically, double-click the "Setup.exe" file on the Setup CD-ROM.)

• To avoid any possible problems, temporarily disable any firewall or antivirus software.

• This procedure explains installation of this product on the same network as your PC.

• Before proceeding, close your web browser.

Select this product to set up and click [Execute].

Click [Camera Setup].

3. Set up this product to view on the LAN.

When using a router supporting UPnPTM, check [Enable]. When using a router not supporting UPnPTM, check [Disable]. Then click [Next>].

Enter the user name and password that were set, and click [OK].

Click [Automatic Setup (Internet Access)].

• Check if your router supports UPnPTM referring to the router's manual. If UPnPTM is not supported, the router has to be manually configured for port forwarding. Refer to the router's manual for instruction on how to do it.

• If you select [Disable], skip to step .

Note

List window

Displays IPv4 or IPv6 information.

Sets up the Internet access to this product.

Sets up this product to view on the LAN.

Manually sets up this product.

Disables IPsec. If disabled, the button is displayed gray.

Displays the Setup page. (See page 34 in the Operating Instructions on the Setup CD-ROM)

StatusPort No.

MAC Address

IP Address

Select this product on the list to set up the Internet access and click [Execute].

Display the list window. (See the previous page)

• The MAC Address on the bottom (see page 11 of the Operating Instructions on the Setup CD-ROM.) of this product shows which product you select on the List window.

• This program searches for this product or the cameras that are connected to the router and displays their MAC Addresses, IP addresses and Port Numbers.

If more than 20 minutes have passed since this product was turned on, this product cannot be set up from the Setup Program. Disconnect the AC cord from the outlet, and reconnect it again, and restart the Setup Program.

4. Set up Internet access to this product

• The port number must be specified at the end of the camera URL.

For example

Using port 80: http://(Cameraname).viewnetcam.com or http://IP Address

Using any other port: http://(Cameraname).viewnetcam.com:Port Number or http://IP Address:Port Number

Registration with the "Viewnetcam.com FREE DDNS service"

• The URL for local network access may be different from the one set up on the previous page. Make a note of the URL here again.

• The banner is displayed only when Internet access has been permitted.

• To ensure that the most current image is displayed, Internet Explorer should be configured as follows. This will not have a negative effect on normal use.

1. While viewing any website, click [Tools] [Internet Options].

2. In the section "Temporary Internet Files", click [Settings] and check [Every visit to the page].

Note

Note

• When [Enable] was selected at the selection "Allow Access from the Internet".

• When [Disable] was selected at the selection "Allow Access from the Internet".

By registering with the Viewnetcam.com FREE DDNS service, you can create a personalized web address at which this product's live video can always be found on the Internet. For detailed information, access "http://www.viewnetcam.com".

To register with the "Viewnetcam.com FREE DDNS service", check [Register with Viewnetcam.com] and click [Next>].

The Enter Network Password window is displayed. Enter the user name and password that were set, and click [OK].

After a while, the "Viewnetcam.com FREE DDNS service" website is displayed. Follow the displayed instructions for registration.

When "Setup completed" is displayed, click [To Single Camera page].

When the Single Camera page is displayed, the setup is completed.

• If you select [Do not register with Viewnetcam.com], skip to step .

• If the message "Failed to configure the router's Port Forwarding by UPnP" is displayed, your router may not support UPnPTM or UPnPTM is not enabled. Enable your router's UPnPTM or set Port Forwarding manually following the router's manual, and try Automatic Setup again. For more information about setting up a router, refer to the Panasonic support web-site at http://panasonic.co.jp/pcc/products/en/netwkcam/.

• If the message "Failed to register with Viewnetcam.com." is displayed, con-firm that the router is connected to the Internet.

Security Warning window on Microsoft Windows XP Service Pack 2To view a video (Motion JPEG) or to listen to audio feature, ActiveX Controls must be installed.Follow the steps shown below to install ActiveX Controls.

Click the warning displayed above the tabs, and click [Install ActiveX Control...].

Click [Install].

Enter this product's MAC address in the data field, and click [Set up camera].

• After about a minute, the Security: Administrator page is displayed.

Setting up this product Using the MAC Address on the Setup Program

Note

After confirming the network settings, click [OK].

Enter the user name and password, and click [Save].

Enter the user name and password that you set, and click [OK].

When the Single Camera page is displayed, the setup is completed.

• See page 16 of the Operating Instructions on the Setup CD-ROM for the Single Camera page.

• If you enable Internet access to this product, follow the procedures below.

• If the Security Warning window is displayed to install ActiveX Controls, click [Yes].

• To install ActiveX Controls on Microsoft Windows XP Service Pack 2, see "Security Warning window on Microsoft Windows XP Service Pack 2" below.

Note

Allow the Internet access to this product.

• When you are using a router supporting UPnPTM

1. Enable the Auto Port Forwarding feature on the UPnPTM page (see page 55 of the Operating Instructions on the Setup CD-ROM).

2. Register with the DynamicDNS service on the DynamicDNS page (see page 58 of the Operating Instructions on the Setup CD-ROM).

3. Confirm the Internet access to this product (see page 12 of the Operating Instructions on the Setup CD-ROM).

NoteIf you cannot access this product, see page 7, 8 and 9 in the Troubleshooting on the Setup CD-ROM.

• When you are using a router not supporting UPnPTM

Follow the procedures shown on page 57 of the Operating Instructions on the Setup CD-ROM.

The Setup Program may not list this product due to your firewall or antivirus software settings on your PC. If you cannot disable your firewall or antivirus software, you can set up this product using this product MAC address as shown below.

Enter the MAC address.

This product's MAC address can be found on the sticker affixed to the bottom of this product (see page 11 of the Operating Instructions on the Setup CD-ROM for details).

Example of connection

IN OUTOUT

ININ OUTOUTININ OUTOUT

AUDIOUDIOI/O VIDEOVIDEO

1212V

Amplifier ormixer

Amplifier

Microphone(Local Audio)

Speaker

Monitor

Analog Camera

Microphone(Remote Audio)

Network

Speaker

network camera server bb-hcs301a

Documents