new generation international design guide - sub-zero &...
TRANSCRIPT
2 | English
Features and specifications are subject to change at any time without notice. Visit wolfappliance.com/specs for the most up-to-date information.
IMPORTANT NOTE: Throughout this guide, dimensions may vary by ± 3 mm.
Contents
3 M Series Ovens
12 E Series Ovens
19 Convection Steam Ovens
24 Gas Cooktops
28 Coffee Systems
33 Downdraft Systems
39 Wolf Warranty
wolfappliance.com | 3
M Series Ovens
Three striking new looks are just the beginning. Superior performance features include an even more advanced dual vertical convection fan system, touch-screen controls, convenient new preset cooking programs, improved interior lighting, and even redesigned hinges. There is more usable space inside for deliciousness on a grand scale.
KEY FEATURES
• Dual VertiCross™ convection system supplies two corner column fans for best heat saturation and distribution.
• Nine cooking modes, including the bake stone and dehydration kits for precise, easy-to-use control.
• Self-cleaning ovens.
• Full-extension racks allow easy access to foods.
• Spring and damper door hinge system for smooth opening and closing of the door.
WOLF M SERIES OVENS
UPPER OVEN LOWER OVEN
M SERIES OVENS
TRANSITIONAL
ICBSO30PM/S/PH
ICBSO30CM/B
ICBSO30TM/S/TH
ICBDO30PM/S/PH
ICBDO27TM/S/TH
ICBDO30CM/B
ICBSO36TM/S/TH
ICBSO27TM/S/TH
ICBDO30TM/S/TH
PROFESSIONAL
CONTEMPORARY
4 | English
WOLF M SERIES OVENS
M Series Ovens
TRANSITIONAL SINGLE OVEN
TRANSITIONAL DOUBLE OVEN
OPEN OVEN DOOR584 mm
BEHIND FRAME
723mm
686mm
65mm
46 mm
543mm
WWIDTH
22mm
36 mmCONDUITCHANNEL
218mm
51mm
WIDTH
TRANSITIONAL W
686 mm Model 683 mm762 mm Model 759 mm914 mm Model (single oven only) 911 mm
OPEN OVEN DOOR
584 mmBEHIND FRAME
1291mm
1254mm
65mm
46 mm
543mm
WWIDTH
22mm
36 mmCONDUITCHANNEL
218mm
51mm
SPECIFICATIONS
INTERIOR CAPACITY L
686 mm Oven 127762 mm Oven 144914 mm Oven 178
INTERIOR DIMENSIONS W H D
686 mm Oven 565 mm 445 mm 505 mm762 mm Oven 641 mm 445 mm 505 mm914 mm Oven 794 mm 445 mm 505 mm
AHAM overall volume.
wolfappliance.com | 5
WOLF M SERIES OVENS
M Series Ovens
PROFESSIONAL SINGLE OVEN
OPEN OVEN DOOR584 mm
BEHIND FRAME
723mm
686mm
83mm
46 mm
543mm
22mm
36 mmCONDUITCHANNEL
218mm
51mm
759 mm
OPEN OVEN DOOR
584 mmBEHIND FRAME
1291mm
1254mm
759 mm
46 mm
543mm
83mm
22mm
36 mmCONDUITCHANNEL
218mm
51mm
UPPER OVEN LOWER OVEN
PROFESSIONAL DOUBLE OVEN
WIDTH
PROFESSIONAL W
762 mm Model 759 mm
SPECIFICATIONS
INTERIOR CAPACITY L
762 mm Oven 144
INTERIOR DIMENSIONS W H D
762 mm Oven 641 mm 445 mm 505 mm
AHAM overall volume.
6 | English
WOLF M SERIES OVENS
OPEN OVEN DOOR
584 mmBEHIND FRAME
1291mm
1254mm
46 mm
543mm
25mm
36 mmCONDUITCHANNEL
218mm
51mm
759 mm
OPEN OVEN DOOR584 mm
BEHIND FRAME
723mm
686mm
46 mm
543mm
25mm
36 mmCONDUITCHANNEL
218mm
51mm
759 mm
M Series Ovens
CONTEMPORARY SINGLE OVEN
CONTEMPORARY DOUBLE OVEN
WIDTH
CONTEMPORARY W
762 mm Model 759 mm
OVEN SPECIFICATIONS
INTERIOR CAPACITY L
762 mm Oven 144
INTERIOR DIMENSIONS W H D
762 mm Oven 641 mm 445 mm 505 mm
AHAM overall volume.
wolfappliance.com | 7
WOLF M SERIES OVENS
Planning Information
The oven can be installed in a standard or flush inset application. If a cooktop is being installed above an oven, a minimum of 6 mm is required between units. Location of the electrical supply within the oven opening may require additional cabinet depth. Refer to the chart below.
Finish the edges of the opening. They may be visible when the door is open.
For flush inset installations, a minimum 3 mm reveal is required on all sides. To ensure consistent 3 mm reveals, each corner of the opening must be exactly 90°.
INSTALLATION REQUIREMENTS
BASE SUPPORT
Single Oven 115 kgDouble Oven 181 kg
TRIM OVERLAP
Top 25 mmBottom 0 mmSides 18 mm
ELECTRICAL
Installation must comply with all applicable electrical codes and be properly grounded (earthed).
Locate the electrical supply flush with the back wall and within the shaded area shown in the illustration for your spe-cific installation on the following pages. For ease of instal-lation, the electrical supply for the oven can be placed in an adjacent cabinet within reach of the conduit.
Performance may be compromised if the electrical supply is less than 220 volts.
The oven is supplied with a single phase and 3-phase convertible power inlet box. The wiring diagram covering the control circuit is provided with the oven.
ELECTRICAL REQUIREMENTS
SINGLE OVEN SINGLE PHASE 3-PHASE
Required Power Supply 220-240 V AC 50/60 Hz
380-415 V AC 50 Hz
Maximum Connected Load 5.4 kW TBDTotal Amps 22 TBD
DOUBLE OVEN SINGLE PHASE 3-PHASE
Required Power Supply 220-240 V AC 50/60 Hz
380-415 V AC 50 Hz
Maximum Connected Load 10.8 kW TBDTotal Amps 45 TBD
8 | English
WOLF M SERIES OVENS
M Series Single Oven
STANDARD INSTALLATION
E
FRONT VIEWSIDE VIEW
NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.
699 mmOPENINGHEIGHT
121 mmTYPICAL
591 mmOPENING
DEPTH
WOPENING WIDTH
TOP VIEW
E127mm
102mm
OPENING WIDTH
MODEL W
686 mm Model 648 mm762 mm Model 724 mm914 mm Model 876 mm
wolfappliance.com | 9
WOLF M SERIES OVENS
M Series Double Oven
STANDARD INSTALLATION
E
FRONT VIEWSIDE VIEW
NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.
1267 mmOPENINGHEIGHT
591 mmOPENING
DEPTH
WOPENING WIDTH
432 mmTYPICAL
TOP VIEW
E
E127mm
102mm
E
OPENING WIDTH
MODEL W
686 mm Model 648 mm762 mm Model 724 mm
10 | English
WOLF M SERIES OVENS
M Series Single Oven
FLUSH INSET INSTALLATION
E
FRONT VIEWSIDE VIEW
*25 mm minimum depth. Shaded areas will be visible and should be finished to match cabinetry.**22 mm for professional and transitional models and 25 mm for contemporary model.
NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.
730 mmFLUSH INSET
HEIGHT
29 mm
3 mm
21 mm
610 mmFLUSH INSET
DEPTH
22 mmOR
25 mm**FINISHEDCLEATS*
WFLUSH INSET WIDTH
TOP VIEW
E
E127mm
102mm
FLUSH INSET WIDTH
MODEL W
686 mm Model 689 mm762 mm Model 765 mm914 mm Model 918 mm
wolfappliance.com | 11
WOLF M SERIES OVENS
M Series Double Oven
FLUSH INSET INSTALLATION
E
FRONT VIEWSIDE VIEW
*25 mm minimum depth. Shaded areas will be visible and should be finished to match cabinetry.**22 mm for professional and transitional models and 25 mm for contemporary model.
NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.
1299 mmFLUSH INSET
HEIGHT
29 mm
3 mm
21 mm
610 mmFLUSH INSET
DEPTH
22 mmOR
25 mm**FINISHEDCLEATS*
WFLUSH INSET WIDTH
432 mmTYPICAL
TOP VIEW
E
E127mm
102mm
FLUSH INSET WIDTH
MODEL W
686 mm Model 689 mm762 mm Model 765 mm
12 | English
E Series Ovens
Stainless models now feature a redesigned stainless steel touch-action control panel, helping to create great meals with ease, as well as adding a striking design feature to the kitchen. Smart technology gives the E series ten cooking modes, with Wolf’s innovative dual convection in single ovens and in the upper unit of double ovens. E series ovens can be installed flush with cabinets for a contemporary, integrated look. Wolf E series ovens are crafted of stainless steel. Tubular oven handles have been updated to match the rest of the new Wolf cooking appliance offering, providing a more cohesive family look.
KEY FEATURES
• NEW! Redesigned stainless steel touch control panel.
• Dual convection—two fans for even heat distribution.
• Ten cooking modes, including the bake stone and dehydration kits for precise, easy-to-use control.
• Self-cleaning ovens.
• Full-extension bottom rack for easier access to foods.
• Balanced door hinge system for smooth opening and closing of the door.
ICBSO30CE/B/TH
ICBSO30TE/S/TH
ICBDO30TE/S/TH
ICBDO30CE/B/TH
ICBSO30PE/S/PH
ICBDO30PE/S/PH
WOLF E SERIES OVENS
E SERIES OVENS
TRANSITIONAL
PROFESSIONAL
CONTEMPORARY
wolfappliance.com | 13
E Series Ovens
SINGLE OVEN
DOUBLE OVEN
603 mmBEHIND FRAME
708mm
759 mm
CONDUITCHANNEL 689
mm
73mm
*25 mm for professional and transitional models and 32 mm for contemporary model.
76 mm
718 mm
559mm
244mm
225mm
25 mm OR32 mm*
OPEN OVEN DOOR
603 mmBEHIND FRAME
1280mm
1261mm
759 mm 73mm
CONDUITCHANNEL
718 mm
559mm
244mm
225mm
76 mm
*25 mm for professional and transitional models and 32 mm for contemporary model.
OPEN OVEN DOOR
25 mm OR32 mm*
SPECIFICATIONS
INTERIOR CAPACITY L
762 mm Oven 127
INTERIOR DIMENSIONS W H D
762 mm Oven 635 mm 419 mm 483 mm
AHAM overall volume.
WOLF E SERIES OVENS
WIDTH
E SERIES W
762 mm Model 759 mm
14 | English
Planning Information
The oven can be installed in a standard or flush inset application. If a cooktop is being installed above an oven, a minimum of 6 mm is required between units. Location of the electrical supply within the oven opening may require additional cabinet depth. Refer to the chart below.
Finish the edges of the opening. They may be visible when the door is open.
For flush inset installations, a minimum 6 mm reveal is required on all sides. To ensure consistent 6 mm reveals, each corner of the opening must be exactly 90°.
INSTALLATION REQUIREMENTS
BASE SUPPORT
Single Oven 115 kgDouble Oven 181 kg
TRIM OVERLAP
Top 13 mmBottom 3 mmSides 17 mm
ELECTRICAL
Installation must comply with all applicable electrical codes and be properly grounded (earthed).
Locate the electrical supply flush with the back wall and within the shaded area shown in the illustration for your spe-cific installation on the following pages. For ease of instal-lation, the electrical supply for the oven can be placed in an adjacent cabinet within reach of the conduit. Unit is supplied with terminal box convertible to single or 3-phase.
The wiring diagram covering the control circuit is provided with the oven.
ELECTRICAL REQUIREMENTS
SINGLE OVEN SINGLE PHASE 3-PHASE
Required Power Supply 220-240 V AC 50/60 Hz
380-415 V AC 50 Hz
Maximum Connected Load 4.4 kW 4.4 kWTotal Amps 19 19
DOUBLE OVEN SINGLE PHASE 3-PHASE
Required Power Supply 220-240 V AC 50/60 Hz
380-415 V AC 50 Hz
Maximum Connected Load 7.4 kW 5.1 kWTotal Amps 32 22
WOLF E SERIES OVENS
wolfappliance.com | 15
WOLF E SERIES OVENS
E Series Single Oven
STANDARD INSTALLATION
E
FRONT VIEWSIDE VIEW
NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.
692 mmOPENINGHEIGHT
610 mmOPENING
DEPTH
724 mmOPENING WIDTH
121 mmTYPICAL
TOP VIEW
E127mm
102mm
16 | English
E
FRONT VIEWSIDE VIEW
NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.
1264 mmOPENINGHEIGHT
610 mmOPENING
DEPTH
724 mmOPENING WIDTH
432 mmTYPICAL
TOP VIEW
E
E127mm
102mm
E
E Series Double Oven
STANDARD INSTALLATION
WOLF E SERIES OVENS
wolfappliance.com | 17
WOLF E SERIES OVENS
E
FRONT VIEWSIDE VIEW
*Will be visible and should be finished to match cabinetry.**25 mm for professional and transitional models and 32 mm for contemporary model.
NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.
721 mmFLUSH INSET
HEIGHT
19 mm
10 mm
24 mm
635 mmFLUSH INSET
DEPTHFINISHEDCLEATS*
772 mmFLUSH INSET WIDTH
25 mmOR
32 mm**
TOP VIEW
981 mmTYPICAL
E
E127mm
102mm
E Series Single Oven
FLUSH INSET INSTALLATION
18 | English
E Series Double Oven
FLUSH INSET INSTALLATION
E
FRONT VIEWSIDE VIEW
*Will be visible and should be finished to match cabinetry.**25 mm for professional and transitional models and 32 mm for contemporary model.
NOTE: Location of electrical supply within opening may require additional cabinet depth.Dashed line represents profile of unit.
1292 mmFLUSH INSET
HEIGHT
432 mmTYPICAL
19 mm
10 mm
24 mm
772 mmFLUSH INSET WIDTH
635 mmFLUSH INSET
DEPTHFINISHEDCLEATS*
25 mmOR
32 mm**
TOP VIEW
E
E127mm
102mm
WOLF E SERIES OVENS
wolfappliance.com | 19
WOLF CONVECTION STEAM OVENS
Convection Steam Ovens
The legacy of the “combination oven” goes back decades, to innovative chefs in America and Europe who embraced the combination of air movement with superheated steam to achieve superior results—from breads and roasts to delicate fishes, seafood and vegetables. Wolf combines the benefits of convection and steam for the most innovative steam oven on the market today. Virtually any dish prepared in a con-ventional oven, range or microwave can also be prepared in the Wolf convection steam oven—with more control. Three distinct styles compliment the look of Wolf ovens, ranges and cooktops. It can be installed in a standard or flush inset application.
KEY FEATURES
• Convection and steam heat with ten cooking modes for superior control.
• Gourmet and Recipes modes for quick and convenient meal preparation.
• Temperature probe, perforated and solid stainless steel pans.
• Operating time, delayed start and descaling features.
CONVECTION STEAM OVENS
TRANSITIONAL
ICBCSO30TE/S/TH
ICBCSO30TM/S/TH
PROFESSIONAL
CONTEMPORARY
ICBCSO30PE/S/PH
ICBCSO30PM/S/PH
ICBCSO30CM/B/TH
20 | English
OPEN OVEN DOOR
548 mmBEHIND FRAME
454mm
446mm
65mm
538 mm
360mm
22 mm
759 mmWIDTH
SPECIFICATIONS
INTERIOR CAPACITY L
All Models 51
INTERIOR DIMENSIONS W H D
All Models 454 mm 280 mm 400 mm
Convection Steam Oven
DIMENSIONS
WOLF CONVECTION STEAM OVENS
wolfappliance.com | 21
WOLF CONVECTION STEAM OVENS
Planning Information
The convection steam oven can be installed in a standard or flush inset application. A minimum base support of 45 kg is required. The electrical supply for the oven must be located in an adjacent cabinet.
Finish the edges of the opening. They may be visible when the door is open.
For flush inset installations, a minimum 3 mm reveal is required on all sides. To ensure consistent 3 mm reveals, each corner of the opening must be exactly 90°.
TRIM OVERLAP
Top 5 mmBottom 0 mmSides 98 mm
ELECTRICAL
Installation must comply with all applicable electrical codes and be properly grounded (earthed).
Locate the electrical supply as shown in the illustrations on the following pages. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.
Performance may be compromised if the electrical supply is less than 220 volts.
ELECTRICAL REQUIREMENTS
Electrical Supply 220-240 VAC, 50 Hz 380-415 VAC 2N, 50 Hz
Service 3700 Watts
Power Cord 2.5 m
22 | English
Convection Steam Oven
STANDARD INSTALLATION
FRONT VIEWSIDE VIEW
Electrical supply must be located in adjacent cabinet within .9 m of opening.Dashed line represents profile of unit.
449 mmOPENINGHEIGHT
548 mmOPENING
DEPTH
TOP VIEW
562 mmOPENING WIDTH
EE
WOLF CONVECTION STEAM OVENS
wolfappliance.com | 23
Convection Steam Oven
FLUSH INSET INSTALLATION
765 mmFLUSH INSET WIDTH
FRONT VIEWSIDE VIEW
FINISHEDCLEATS*
584 mmFLUSH INSET
DEPTH25 mm
*Will be visible and should be finished to match cabinetry.
NOTE: Electrical supply must be located in adjacent cabinet within .9 m of opening.Dashed line represents profile of unit.
460 mm FLUSH INSET
HEIGHT
8 mm
3 mm
102 mmA
TOP VIEW
EE
WOLF CONVECTION STEAM OVENS
24 | English
WOLF GAS COOKTOPS
Gas Cooktops
Like their built-in oven counterparts, the new generation of Wolf gas cooktops features three new looks—Transi-tional, Professional, and Contemporary. New performance enhancements make delicious results even more of a certainty than ever. Multiple sizes, choice of knob colors, distinctly different grates, and even a new way to integrate with custom cabinetry—the new gas cooktops offer excep-tional design flexibility.
KEY FEATURES
• Dual-stacked, sealed burners for precise control and easy cleanup.
• Flame recognition and automatic reignition for safety and ease of use.
• True simmer setting on all burners prevents scorching.
• Illuminated, cool-to-touch knobs for user-friendly comfort.
ICBCG365P/S
ICBCG304P/S
ICBCG365T/S
ICBCG304T/S
ICBCG365C/S
GAS COOKTOPS
TRANSITIONAL
PROFESSIONAL
CONTEMPORARY—COMING SOON!
wolfappliance.com | 25
WOLF GAS COOKTOPS
Gas Cooktops
762 mm TRANSITIONAL 914 mm TRANSITIONAL
762 mm
22 mmALL SIDES
533 mm
102 mm
914 mm
22 mmALL SIDES
102 mm
533 mm
762 mm PROFESSIONAL 914 mm PROFESSIONAL
762 mm
22 mmALL SIDES
533 mm
102 mm
914 mm
22 mmALL SIDES
102 mm
533 mm
BURNER RATING—kW
762 mm GAS COOKTOP HIGH
Large 5.3Medium 3.5(2) Small 2.7
914 mm GAS COOKTOP HIGH
Large 5.3Medium 3.5(3) Small 2.7
26 | English
WOLF GAS COOKTOPS
GAS SUPPLY
A gas supply line of 19 mm rigid pipe must be provided to the cooktop. If local codes permit, a certified, .9 m long, 13 mm or 19 mm ID flexible metal appliance connector is recommended to connect the units 1/2" NPT (or ISO 7/1) male inlet to the gas supply line.
Wolf natural gas cooktops will function up to 3124 m in altitude without adjustment and LP gas cooktops will func-tion up to 2621 m. If the installation exceeds these eleva-tions, contact your authorized Wolf dealer for a high altitude conversion kit.
GAS SUPPLY REQUIREMENTS
NATURAL GAS
Gas Supply Pressure 12.5 mbMin Line Pressure 17.5 mbMax Pressure to Regulator 100 mb
LP GAS
Gas Supply Pressure 25 mbMin Line Pressure 27.4 mbMax Pressure to Regulator 100 mb
Planning Information
A minimum height clearance of 140 mm is required from the top of the countertop to any combustible surface directly below the cooktop.
If a cooktop is being installed above an oven, a minimum of 6 mm is required between units.
ELECTRICAL
Installation must comply with all applicable electrical codes and be properly grounded (earthed).
ELECTRICAL REQUIREMENTS
GAS COOKTOP
Electrical Supply 220-240 V AC, 50/60 HzService 10 amp dedicated circuitReceptacle grounding-type (earthed)
wolfappliance.com | 27
WOLF GAS COOKTOPS
Gas Cooktop
STANDARD INSTALLATION
254 mm
102 mm
89 mm
FRONT VIEWSIDE VIEW
COUNTERTOP CUT-OUT
NOTE: Shaded area above countertop indicates minimum clearance to combustible surfaces,combustible materials cannot be located within this area.Electrical and gas supply location only applies to installations with built-in oven.
762 mm
WWIDTH
330 mm457 mm
229mm
495 mm
64 mm
64 mm
E G
CUT-OUT WIDTH
MODEL W
762 mm Cooktop 737 mm914 mm Cooktop 889 mm
28 | English
WOLF COFFEE SYSTEMS
Coffee Systems
Make professional-quality brewed coffee, espresso, cappu-cinno, latte and more. The Wolf coffee system automatically steams and foams the milk perfectly. Water temperature and brew strength are adjustable. Uses either whole-bean or ground coffee. The design pairs beautifully, either side-by-side or in a tower application, with other Wolf products such as the convection steam oven. The coffee system can be installed in a standard or flush inset application.
KEY FEATURES
• Create perfectly brewed coffee, espresso, cappuccino, macchiato and latte at home.
• Separate hot water dispenser for tea.
• Mounted glide system provides easy access to the unit, no direct water line is needed.
• Milk frothing pitcher with adjustable settings, detaches for refrigerated storage and easy cleaning.
• Built-in coffee mill with adjustable grind settings.
• Auto on, auto off and descaling features.
COFFEE SYSTEMS
610 mm MODELS
762 mm E Series Trim
762 mm M Series Trim
TRANSITIONAL
ICBEC24/S
PROFESSIONAL
CONTEMPORARY
762 mm E Series Trim
762 mm M Series Trim
762 mm M Series Trim
ICBEC24/B
wolfappliance.com | 29
WOLF COFFEE SYSTEMS
394 mmBEHIND FRAME
454mm
22 mm
UNITFULL EXTENSION
464mm
WWIDTH
WIDTH
COFFEE SYSTEM W
610 mm Model 597 mm762 mm Model 759 mm
Coffee System
DIMENSIONS
30 | English
Planning Information
The coffee system can be installed in a standard or flush inset application. A minimum base support of 45 kg is required. The sides of the cabinetry opening must be ade-quate to support installation of the mounting slides. Refer to the illustrations below.
Finish the edges of the opening. They may be visible when the door is open.
For flush inset installations, a minimum 3 mm reveal is required on all sides. To ensure consistent 3 mm reveals, each corner of the opening must be exactly 90°.
TRIM OVERLAP
OVERLAP 610 mm MODEL 762 mm MODEL
Top 5 mm 5 mmBottom 0 mm 0 mmSides 18 mm 98 mm
WOLF COFFEE SYSTEMS
ELECTRICAL
Installation must comply with all applicable electrical codes and be properly grounded (earthed).
Locate the electrical supply as shown in the illustrations on the following pages. A separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.
ELECTRICAL REQUIREMENTS
Electrical Supply 230 VAC, 50 Hz
Service 10 amp dedicated circuit
Power Cord 1.8 m
356mm
254mm
19 mmTYPICAL
Side support.
Slide installation.
wolfappliance.com | 31
SLIDESUPPORT
SLIDESUPPORT
FRONT VIEWSIDE VIEW
TOP VIEW
E449 mmOPENINGHEIGHT
548 mmOPENING
DEPTH
WOPENING WIDTH
NOTE: 610 mm and 762 mm models require the same opening dimensions.Dashed line represents profile of unit.
Coffee System
STANDARD INSTALLATION
OPENING WIDTH
COFFEE SYSTEM W
610 mm Model 562 mm762 mm Model 562 mm
WOLF COFFEE SYSTEMS
32 | English
WFLUSH INSET WIDTH
FRONT VIEWSIDE VIEW
FINISHEDCLEATS*
584 mmFLUSHINSETDEPTH25 mm
*Will be visible and should be finished to match cabinetry.
Dashed line represents profile of unit.
460 mm FLUSH INSET
HEIGHT
8 mm
3 mm
A
TOP VIEW
E
SLIDESUPPORT
SLIDESUPPORT
Coffee System
FLUSH INSET INSTALLATION
FLUSH INSET WIDTH
COFFEE SYSTEM W A
610 mm Model 603 mm 21 mm762 mm Model 765 mm 102 mm
WOLF COFFEE SYSTEMS
wolfappliance.com | 33
WOLF DOWNDRAFT SYSTEMS
Downdraft Ventilation
Constructed of heavy duty stainless steel, the Wolf down-draft rises from the countertop to whisk away odor and smoke into stainless steel, mesh filters and can be low-ered beneath the countertop when not in use. Downdrafts integrate perfectly with transitional induction and electric cooktops, gas cooktops and some integrated modules, they can also be installed with 762 mm sealed burner rangetops.
KEY FEATURES
• Three-speed blower control with boost.
• Remote-mounted control module with LED indicators.
• Delay-off feature to automatically turn unit off.
• Stainless steel, mesh filters.
• Reversible motor box.
• Adjustable discharge.
ICBDD45
ICBDD36
ICBDD30
DOWNDRAFTS
34 | English
WOLF DOWNDRAFT SYSTEMS
51 mm
356 mm
730 mm
WDOWNDRAFT WIDTH
ACHIMNEY WIDTH
172mm
254mm
330mm
330mm
381mm
64 mm
60 mm
NOTE: Shaded line represents internal blower box with 152 mm round discharge.
19 mm
Downdraft
DIMENSIONS
WIDTH
MODEL W A
ICBDD30 762 mm 673 mmICBDD36 914 mm 826 mmICBDD45 1143 mm 978 mm
wolfappliance.com | 35
Planning Information
Wolf downdrafts can be installed with most Wolf cooktops, but are not compatible with contemporary induction and electric cooktops and the grill, steamer and fryer modules. Downdrafts can be installed with sealed burner rangetop model ICBSRT304. An accessory trim kit is necessary for this installation. Contact an authorized Wolf dealer for details.
The remote-mounted control module must be located within 3 m of the downdraft assembly and a minimum 76 mm from the edge of the cooktop cut-out.
Internal and remote blowers are available through an autho-rized Wolf dealer.
Internal blowers include a 152 mm round discharge and can be front or rear mounted. It can be discharged in any direc-tion by rotating the blower box. Remote blowers include a 254 mm discharge and can be discharged from the front or rear.
Consult a qualified HVAC professional for specific installa-tion and ducting applications.
WOLF DOWNDRAFT SYSTEMS
ELECTRICAL
Installation must comply with all applicable electrical codes and be properly grounded (earthed).
Certain installations may require that the electrical supply be placed in an adjacent cabinet.
ELECTRICAL REQUIREMENTS
DOWNDRAFTS
Electrical Supply 220-240 V AC, 50 Hz 220 V AC, 60 Hz
Service 10 amp dedicated circuitReceptacle grounding-type (earthed)
36 | English
E
FRONT VIEWSIDE VIEW
*152 mm back from countertop cut-out when internal blower is rear mounted.
NOTE: Internal blower 152 mm round, side, rear or bottom discharge. Remote blower 254 mm round, rear discharge.Centerline indicates center of downdraft cut-out.
540mm
540 mm210 mm*
COOKTOP CUT-OUT
68 mm
TOP VIEW
594 mm
210 mm*
WDOWNDRAFT
CUT-OUT WIDTH
E
WOLF DOWNDRAFT SYSTEMS
Downdraft
INSTALLATION WITH COOKTOP
CUT-OUT WIDTH
MODEL W
ICBDD30 699 mmICBDD36 851 mmICBDD45 1003 mm
wolfappliance.com | 37
FRONT VIEWSIDE VIEW
483 mmPLATFORM DEPTH
FRONT VIEWSIDE VIEW
*152 mm back from countertop cut-out when internal blower is rear mounted.
NOTE: Internal blower 152 mm round, side, rear or bottom discharge. Remote blower 254 mm round, rear discharge.Centerline indicates center of downdraft cut-out.
540mm
210 mm*
TOP VIEW
WDOWNDRAFT
CUT-OUT WIDTH
210 mm*
540 mm 594 mm
RANGETOP OPENING
68 mm E
E
WOLF DOWNDRAFT SYSTEMS
Downdraft
INSTALLATION WITH SEALED BURNER RANGETOP
CUT-OUT WIDTH
MODEL W
ICBDD30 699 mm
38 | English
WOLF DOWNDRAFT SYSTEMS
Downdraft Blower Options
BLOWER
INTERNAL ICBDD30 ICBDD36 ICBDD45
1014 m3/hr • • •
REMOTE ICBDD30 ICBDD36 ICBDD45
1014 m3/hr • • •2028 m3/hr • • •
Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc. Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are registered trademarks and service marks of Sub-Zero, Inc. (collectively, the “Company Marks.”) All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
wolfappliance.com | 39
Wolf Products Limited Warranty
INTERNATIONAL PRODUCTS
FOR RESIDENTIAL USE ONLY
FULL TWO YEAR WARRANTY
For two years from the date of original installation, your Wolf Appliance product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Wolf Appliance under the above warranty must be performed by Wolf factory certified service, unless otherwise specified by Wolf Appliance, Inc. Service will be provided during normal business hours.
LIMITED THIRD THROUGH FIFTH YEAR WARRANTY
For five years from the date of original installation, Wolf Appliance will repair or replace the following parts that prove to be defective in materials or workmanship: gas burners (excluding appearance), electric heating elements, blower motors (ventilation hoods), electronic control boards, magnetron tubes and induction generators. The part(s) will be repaired or replaced, free of charge, with the owner paying for all other costs including labor. All service provided by Wolf Appliance under the above warranty must be performed by Wolf factory certified service, unless otherwise specified by Wolf Appliance, Inc. Service will be provided during normal business hours.