nla-5 series rigging manual 2015.12.01.. preparation material 2
TRANSCRIPT
![Page 1: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/1.jpg)
NLA-5 Series Rigging Manual
2015.12.01.
![Page 2: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/2.jpg)
Preparation Material
2
![Page 3: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/3.jpg)
ㄴ
Preparation Material- 1
3
1. Chain block or Electric
hoist
2. Shackle (over 5/8 inch)
3. Sling belt
12
3
![Page 4: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/4.jpg)
ㄴ
Preparation Material - 2
4
1. FRONT BAR
2. BACK BAR
3. Bolt, Spring washer,
Flat washer
321
4. Bolt & Washer
Assembly
(Must use 2 washers)
4
![Page 5: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/5.jpg)
ㄴ
Preparation Material - 3
5
21
1. Short bar is Back bar when connect
Frame → NLA-15S NLA-15S → NLA-5.
2. Long bar is Back bar when connect
NLA-5 → NLA-5.
![Page 6: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/6.jpg)
ㄴ
Preparation Material - 4
6
1. Shackle (1/2 inch) 1EA
1
![Page 7: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/7.jpg)
ㄴ
Preparation Material - 5
7
1. Electric Screw Driver
2. Hexagonal Tip (5mm)
3. Hexagonal
Wrench_Manual (5mm)
12
3
![Page 8: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/8.jpg)
Chain block Connection
8
![Page 9: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/9.jpg)
ㄴ
Chainblock Connection - 1
9
Like the above picture, connect a sling belt to a trus
s.
(When you install it to H-beam, lower circled 1 to
down side.)
1
![Page 10: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/10.jpg)
ㄴ
Chainblock Connection - 2
10
Like the picture, assemble the sling belt hanger to the
shackle.
![Page 11: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/11.jpg)
ㄴ
Chainblock Connection - 3
11
Connected sling belt and shackle
![Page 12: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/12.jpg)
ㄴ
Chainblock Connection - 4
12
Connect hanger of chain block(or hoist) to shackle.
![Page 13: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/13.jpg)
ㄴ
Chainblock Connection - 5
13Connected chain block / hoist
![Page 14: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/14.jpg)
Frame Assembly
14
![Page 15: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/15.jpg)
ㄴ
Frame Assembly - 1
15
1. NLA-15S2. NLA-5 FRAME
2
1
![Page 16: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/16.jpg)
ㄴ
Frame Assembly - 2
16
Put NLA-5 FRAME on NLA-15S.
![Page 17: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/17.jpg)
ㄴ
Frame Assembly - 3
17
Tighten up and down holes in FRONT BAR
with bolts.
![Page 18: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/18.jpg)
ㄴ
Frame Assembly - 4
18
Adjust frame to make an alignment of
middle hole and the screw hole in the
frame.(1)
1
![Page 19: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/19.jpg)
ㄴ
Frame Assembly - 5
19
Tighten them with a bolt.
(Use an electric screw driver for your
convenience)
![Page 20: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/20.jpg)
ㄴ
Frame Assembly - 6
20
Connect rear side of the frame using short back
bar.
![Page 21: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/21.jpg)
ㄴ
Frame Assembly - 7
21
Tighten whole points using manual
hexagonal wrench.
![Page 22: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/22.jpg)
ㄴ
프레임 조립 - 8
22
Connected frame on NLA-15S
![Page 23: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/23.jpg)
ㄴ
Frame Assembly - 9
23
Install ½ inch shackle to a preferred spot.
![Page 24: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/24.jpg)
ㄴ
Frame Assembly - 10
24
Connect the shackle to the hanger of chain
block(or hoist).
![Page 25: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/25.jpg)
NLA-5 Assembly
25
![Page 26: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/26.jpg)
ㄴ
Speaker Assembly- 1
26
Lift up frame(1) with chain block, and put
one NLA-5(2) under the frame.
1
2
![Page 27: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/27.jpg)
ㄴ Speaker Assembly - 2
27
Align front part of the speakers by
lowering the frame.
![Page 28: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/28.jpg)
ㄴ
Speaker Assembly - 3
28
Firstly, tighten the up and down holes of F
RONT BAR with bolts.
![Page 29: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/29.jpg)
ㄴ
Speaker Assembly - 4
29
Match middle hole in the bar and the speaker by
adjusting position of them.
![Page 30: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/30.jpg)
ㄴ
Speaker Assembly - 5
30
Tighten the middle hole with bolts.
![Page 31: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/31.jpg)
ㄴ
Speaker Assembly - 6
31
Connect the lower part of short back bar with
bolts.
![Page 32: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/32.jpg)
ㄴ
Speaker Assembly - 7
32
Lift up the speaker with chain block, and
match up hole with speaker’s hole.
![Page 33: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/33.jpg)
ㄴ
Speaker Assembly - 8
33
Connect the up hole with a bolt.
![Page 34: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/34.jpg)
ㄴ
Speaker Assembly - 9
34
Completed 1 set of NLA-5
![Page 35: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/35.jpg)
ㄴ
Speaker Assembly - 10
35
Put another NLA-5 below.
![Page 36: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/36.jpg)
ㄴ
Speaker Assembly - 11
36
Align front part of NLA-5 using chain
block.
![Page 37: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/37.jpg)
ㄴ
Speaker Assembly - 12
37
Connect the up and down hole in the FRO
NT BAR with bolts.
![Page 38: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/38.jpg)
ㄴ
Speaker Assembly - 13
38
Match middle hole in the bar and the speaker by
adjusting position of them.
![Page 39: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/39.jpg)
ㄴ
Speaker Assembly - 14
39
Tighten the middle hole with bolts.
![Page 40: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/40.jpg)
ㄴ
Speaker Assembly - 15
40
Connect the downside of the long back
bar with bolts.
![Page 41: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/41.jpg)
ㄴ
Speaker Assembly - 16
41
Rear part of NLA-5
5
0
10
Angles for each hole
![Page 42: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/42.jpg)
ㄴ
Speaker Assembly - 17
42
You can see that this picture is set to 0
degree.
5
0
10
![Page 43: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/43.jpg)
ㄴ
Speaker Assembly - 18
43
Choose your preferred angle
of hole using chain block.
The example in the photo is 0
degree.
![Page 44: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/44.jpg)
ㄴ
Speaker Assembly - 19
44
Connect it with a bolt.
![Page 45: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/45.jpg)
ㄴ
Speaker Assembly - 20
45
Completed 2 set of NLA-5
![Page 46: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/46.jpg)
ㄴ
Speaker Assembly - 21
46
Fully completed figure after repeated
process.
![Page 47: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/47.jpg)
NLA-5 RACK Assembly
47
![Page 48: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/48.jpg)
ㄴ
Speaker Assembly- 1
48
Insert an amplifier to NLA-5 RACK.
![Page 49: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/49.jpg)
ㄴ Speaker Assembly - 2
49
1. Fill up spaces with blank panel.
2. Connect power cable, speaker cable,
and LAN cable beforehand.
![Page 50: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/50.jpg)
ㄴ Speaker Assembly - 3
50
Put NLA-5 FRAME on NLA-5 Rack.
![Page 51: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/51.jpg)
ㄴ Speaker Assembly - 4
51
Tighten up and down holes in FRONT BAR
with bolts.
![Page 52: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/52.jpg)
ㄴ Speaker Assembly - 5
52
Adjust frame to make an alignment of
middle hole and the screw hole in the
frame.(1)
1
![Page 53: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/53.jpg)
ㄴ Speaker Assembly - 6
53
Tighten them with a bolt.
(Use an electric screw driver for your
convenience)
![Page 54: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/54.jpg)
ㄴ Speaker Assembly - 7
54
Connect rear side of the frame using short back
bar.
![Page 55: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/55.jpg)
ㄴ Speaker Assembly - 8
55
Tighten whole points using manual
hexagonal wrench.
![Page 56: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/56.jpg)
ㄴ Speaker Assembly - 9
56
Connected frame on NLA-5 RACK
![Page 57: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/57.jpg)
ㄴ Speaker Assembly - 10
57
Put NLA-15S under NLA-5 RACK.
![Page 58: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/58.jpg)
ㄴ Speaker Assembly - 11
58
Tighten up and down holes in FRONT BAR
with bolts.
![Page 59: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/59.jpg)
ㄴ Speaker Assembly - 12
59
Connect the middle with a bolt.
![Page 60: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/60.jpg)
ㄴ Speaker Assembly - 13
60
Connect the lower part of short back bar with
bolts.
![Page 61: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/61.jpg)
ㄴ Speaker Assembly - 14
61
Connect the up hole with a bolt.
![Page 62: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/62.jpg)
ㄴ
Speaker Assembly - 15
62
Put one NLA-5 below, and tighten the up
and down holes of FRONT BAR with bolts.
![Page 63: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/63.jpg)
ㄴ
Speaker Assembly - 16
63
Match middle hole in the bar and the speaker by
adjusting position of them.
![Page 64: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/64.jpg)
ㄴ
Speaker Assembly - 17
64
Tighten the middle hole with bolts.
![Page 65: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/65.jpg)
ㄴ
Speaker Assembly - 18
65
Connect the downside of the short back bar
with bolts.
![Page 66: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/66.jpg)
ㄴ
Speaker Assembly - 19
66
Lift up the speaker with chain block, and
match up hole with speaker’s hole.
![Page 67: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/67.jpg)
ㄴ
Speaker Assembly - 20
67
Connect the up hole with a bolt.
![Page 68: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/68.jpg)
ㄴ
Speaker Assembly - 21
68
Completed 1 set of NLA-5
![Page 69: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/69.jpg)
ㄴ
Speaker Assembly - 22
69
Put another NLA-5 below.
![Page 70: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/70.jpg)
ㄴ
Speaker Assembly - 23
70
Align front part of NLA-5 using chain
block.
![Page 71: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/71.jpg)
ㄴ
Speaker Assembly - 24
71
Connect the up and down hole in the FRO
NT BAR with bolts.
![Page 72: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/72.jpg)
ㄴ
Speaker Assembly - 25
72
Match middle hole in the bar and the speaker by
adjusting position of them.
![Page 73: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/73.jpg)
ㄴ
Speaker Assembly - 26
73
Tighten the middle hole with bolts.
![Page 74: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/74.jpg)
ㄴ
Speaker Assembly - 27
74
Connect the downside of the long back
bar with bolts.
![Page 75: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/75.jpg)
ㄴ
Speaker Assembly - 28
75
Rear part of NLA-5
5
0
10
Angles for each hole
![Page 76: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/76.jpg)
ㄴ
Speaker Assembly - 29
76
You can see that this picture is set to 0
degree.
5
0
10
![Page 77: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/77.jpg)
ㄴ
Speaker Assembly - 30
77
Choose your preferred angle
of hole using chain block.
The example in the photo is 0
degree.
![Page 78: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/78.jpg)
ㄴ
Speaker Assembly - 31
78
Connect it with a bolt.
![Page 79: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/79.jpg)
ㄴ
Speaker Assembly - 32
79
Completed 2 set of NLA-5
![Page 80: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/80.jpg)
ㄴ
Speaker Assembly - 33
80
Fully completed figure after repeated
process.
![Page 81: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/81.jpg)
Caution
81
![Page 82: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/82.jpg)
ㄴ
Caution
82
1. You should insert spring washer and flat
washer for your bolts.
2. THREE holes in the front part of the speaker
must be connected with bolts.
(Connecting only 2 holes(up&down) might
cause a problem)
3. Position for shackle connecting to the frame
is up to user’s preference.
![Page 83: NLA-5 Series Rigging Manual 2015.12.01.. Preparation Material 2](https://reader035.vdocument.in/reader035/viewer/2022062500/5697bfc71a28abf838ca7871/html5/thumbnails/83.jpg)
ㄴ
Caution
83
4. For tightening bolts, electric screw driver is
more convenient and safe than manual
hexagonal wrench.
5. When you use electric screw driver, it is
recommended to use slow motor speed. (Fast
motor speed easily makes a crooked bolt)
6. For your safety and convenience, you have to
tighten bolts with manual hexagonal wrench
after you use electric screw driver.