non-ambient diffraction with d8 advance eco and mtc … · mtc-hightemp stage, 4.0 degree axial...
TRANSCRIPT
Innovation with IntegrityXRD
Non-Ambient Diffraction with D8 ADVANCE ECO and MTC-HIGHTEMP
Application Note XRD 611
In-situ diffraction studies provide insight into structural changes and reactivity under non-ambient conditions. For example, barium titanate (BaTiO3) undergoes a reversible phase change from tetragonal to cubic above 130 °C.1
Access to higher temperatures, however, is often required. Anatase (TiO2) converts irreversibly to the rutile polymorph at elevated temperatures. Reported transition temperatures vary from 400 °C - 1200 °C due to differences in particle size/shape, surface area, impurities, and various other parameters.2-3
Summaryzz Ceramic materials were characterized by XRD
at high temperatureszz D8 ADVANCE ECO (1 kW) provides fast scan
speeds with exceptional signal-to-noisezz MTC-HIGHTEMP capable of accessing
temperatures up to 1600 °C
Direct measurement of this conversion is possible with non-ambient diffraction.
Figure 1 2D intensity map for BaTiO3 scans taken from 100 °C to 150 °C and back to 100 °C. A clear phase transition is observed at 130 °C on both heating and cooling. The region indicated by the dashed white line is highlighted in figure 2 for clarity.
BaTiO3 was characterized as received without any additional processing. Diffraction data were collected in 5 degree increments from 100 °C to 150 °C and again on cooling to 100 °C. Each scan was collected over 5 min with rapid heating steps (< 1 min) between each scan.
Diffractograms are shown in Figure 1 as a 2D intensity map, showing a clear, reversible transition between tetragonal and cubic symmetries at 130 °C on both heating and cooling. Temperatures are indicated with the side-view. Figure 2 shows a closer look at the high angle region. Individual scans taken at 100 °C and 140 °C are shown in Figure 3 along with reference patterns for the two BaTiO3 polymorphs.
Case Study: BaTiO3
Figure 2 Zoomed in region of 2D intensity map for BaTiO3. The dashed line is drawn at 130 °C as a visual guide.
Figure 3 Identification of BaTiO3 polymorphs at 100 °C and 140 °C.
Data were collected using a D8 ADVANCE ECO diffractometer configured with copper (Cu) radiation (40 kV, 25 mA), fixed divergence slits (0.6 mm), MTC-HIGHTEMP stage, 4.0 degree axial Soller slits, and SSD160 silicon strip detector.
Two titanate systems, (1) BaTiO3 and (2) CaTiO3 (perovskite), were characterized in this study. Reversible structural transitions were observed in phase pure BaTiO3 on both heating and cooling. For the perovskite system, CaCO3 and TiO2 precursors were mixed together and characterized while heating to investigate formation of the final CaTiO3 phase.
2
Figure 4 2D intensity map for reaction of calcite (CaCO3) and anatase (TiO2) on heating from room temperature to 1500 °C. Calcite decomposes to lime (CaO) and reacts with anatase to form the perovskite (CaTiO3) phase between 700 °C and 800 °C. At higher temperatures, the formation of perovskite continues while excess anatase is converted to the rutile polymorph. At 1400 °C, the excess rutile melts to a glassy phase.
Case Study: CaTiO3
Figure 5 Identification of crystalline phases present at various temperatures.
Conclusions
Measurements of several oxide materials were successfully performed with the D8 ADVANCE ECO equipped with MTC-HIGHTEMP stage. The reversible phase transition of barium titanate at 130 ˚C was clearly observed. Additionally, the complex reaction between calcite and anatase was characterized at temperatures ranging from 30˚C to 1500˚C. The data described here highlight the importance of diffraction studies at high temperatures, providing insights into structural changes and reactivity.
References
[1] M.B. Smith; K. Page; T. Siegrist; P.L. Red-mond; E.C. Walter; R. Seshadri; L.E. Brus; M.L. Steigerwald J. Am. Chem. Soc. 2008, 130, 6955-6963.
[2] A.W. Czanderna; C.N. Ramachandra Rao; J.M. Honig Trans. Faraday Soc. 1958, 54, 1069-1073.
[3] D.A.H. Hanaor and C.C. Sorrell J. Mater. Sci. 2011, 46, 855-874.
Calcite (CaCO3) and anatase (TiO2) were ground together and then mounted onto the heating filament. Diffractograms were collected every 100 °C from 30 °C - 1000 °C and then every 50 °C from 1000 °C - 1500 °C.
Data visualization by 2D intensity map (Figure 4) helps to identify regions of interest. For example, CaCO3 decomposition is observed at ~ 700 °C with full conversion to lime (CaO) at 800 °C. The perovskite structure begins to form in conjunction with the formation of lime and continues until the Ca precursor is fully consumed at 1200 °C – this is evidenced by the appearance of new, strong diffraction peaks at ~33 °2q, 47 °2q, and 58 °2q. Excess anatase is converted to rutile at 900 °C before finally melting above 1400 °C. Selected scans (30 °C, 800 °C, 1000 °C, 1400 °C) are shown in Figure 5 along with reference patterns for identified phases. In addition to the phase transformations linked to the appearance and disappearance of peaks, increases in lattice parameter due to thermal expansion are clearly shown as shifts in the peaks to lower angles.
3
PLAN in DIFFRAC.WIZARDzz Configure physical and computer controlled instrument
settingszz Setup snapshot and advanced scanning 0D, 1D or 2D
measurementszz Create detailed temperature profiles including soak
times and temperature ramp rates
DIFFRAC.SUITE Workflow for Non-Ambient Diffraction
MEASURE in DIFFRAC.COMMANDERzz Launch complex experimentszz Directly control the non-ambient conditionzz View data in real time
ANALYZE in DIFFRAC.EVAzz Begin analysis while the data is collectingzz Identify phases with search/matchzz Visualize phase changes in waterfall and 2D plots
Worldwide offices
bruker.com/baxs-offices
Bruker AXS GmbH
www.bruker.com Bru
ker
AX
S is
con
tinua
lly im
prov
ing
its p
rodu
cts
and
rese
rves
the
rig
ht t
o ch
ange
spe
cific
atio
ns w
ithou
t no
tice.
O
rder
No.
DO
C-A
88-E
XS
611.
© 2
018
Bru
ker
AX
S.