ntc thermistors - docs-emea.rs-online.com · ntc thermistors ntc thermistors please read caution...
TRANSCRIPT
MurataManufacturing Co., Ltd. Cat.No.R44E-6
NTC Thermistors
NTCTHERMISTORS
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
1
2
3
4
5
6
Part Numbering 2
Basic Characteristics 4
for Temperature Compensation 0201(0603) Size 5
for Temperature Compensation 0402(1005) Size 6
for Temperature Compensation 0603(1608) Size 8
for Temperature Compensation 0805(2012) Size 10
for Temperature Compensation Temperature Characteristics (Reference Value) 12
Chip Type !Caution/Notice 15
Chip Type Package 18
for Temperature Sensor Resin Coated Radial Lead Type 21
for Temperature Sensor Temperature Characteristics (Reference Value) 23
for Temperature Sensor Lead Type !Caution/Notice 24
for Temperature Sensor Lead Type NTSA0/NTSD0 Series Package 26
for Inrush Current Suppression Lead Type 27
Current-R Ratio (RT/R25) / Current-Temperature Characteristics (Typical) 29
for Inrush Current Suppression Lead Type !Caution / Notice 33
for Inrush Current Suppression Lead Type Package 35
CONTENTS AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
1
2
3
4
5
6
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
y
J
e
18
w
P
r
XH
t
103
u
03
i
RBNC
q
2
o Part Numbering The structure of the "Global Part Numbers" that have been adopted since June 2001 and the meaning of each code are described herein.If you have any questions about details, inquire at your usual Murata sales office or distributor.( )
qProduct ID
wSeries
yResistance Tolerance
uIndividual Specifications
NTC Thermistors for Temperature Compensation Chip Type
NC NTC Thermistors Chip Type
F
J
K
P
±1%
±5%
±10%
03
Individual Specifications
Product ID
Code
Code
Series
Resistance Tolerance
Code
(Global Part Number)
tResistance
Expressed by three figures. The unit is ohm (Ω). The first and second figures are signficant digits, and the third figure expresses the number of zeros which follow the two figures. If there is a decimal point, it is expressed by the capital letter "R". In this case, all figures are significant digits.
Please contact us for details.
102
103
104
Ex.)
1kΩ
10kΩ
100kΩ
Code Resistance
Sturcture, others
iPackaging
RA
RB
RC
RD
Plastic Taping 8mm Pitch
Paper Taping 4mm Pitch
Paper Taping 2mm Pitch (10000 pcs.)
Paper Taping 2mm Pitch (15000 pcs.)
Code Packaging
Plated Termination Series
eDimensions (LgW )
03
15
18
21
Code Dimensions (LgW )
0.60g0.30mm
1.00g0.50mm
1.60g0.80mm
2.00g1.25mm
EIA
0201
0402
0603
0805
rTemperature Characteristics
WB
WD
WF
WM
XC
XF
XQ
XH
XM
XV
XW
Code Temperature Characteristics
Nominal B-Constant 4050e4099K
Nominal B-Constant 4150e4199K
Nominal B-Constant 4250e4299K
Nominal B-Constant 4500e4549K
Nominal B-Constant 3100e3149K
Nominal B-Constant 3250e3299K
Nominal B-Constant 3650e3699K
Nominal B-Constant 3350e3399K
Nominal B-Constant 3500e3549K
Nominal B-Constant 3900e3949K
Nominal B-Constant 3950e3999K
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
t
F
w
SA0
e
XH
r
103
y
E1
u
B0NT
q
3
qProduct ID
wSeries
tResistance Tolerance
yIndividual Specifications
NTC Thermistors for Temperature Sensor Lead Type
NT NTC Thermistors
E
F
±3%
±1%
E1
Individual Specifications
Product ID
Code Resistance Tolerance
Code
(Global Part Number)
rResistance
Expressed by three figures. The unit is ohm (Ω). The first and second figures are signficant digits, and the third figure expresses the number of zeros which follow the two figures. If there is a decimal point, it is expressed by the capital letter "R". In this case, all figures are significant digits.
202
203
Ex.)
2kΩ
20kΩ
Code Resistance
Lead Style, others
SA0
SD0
for Temperature Sensors No Lead-coating Type
for Temperature Sensors Lead-coating Type
Code
uPackaging
A0
B0
Ammo Pack
Bulk
Code Packaging
Series
eTemperature Characteristics
WB
WC
WD
WF
XM
XH
XR
XV
Nominal B-Constant 4050e4099K
Nominal B-Constant 4100e4149K
Nominal B-Constant 4150e4199K
Nominal B-Constant 4250e4299K
Nominal B-Constant 3500e3549K
Nominal B-Constant 3350e3399K
Nominal B-Constant 3700e3749K
Nominal B-Constant 3900e3949K
Code Temperature Characteristics
y
B0
e
160
r
L
t
BMNT
q w
PA7
qProduct ID
wSeries
rResistance Tolerance
tIndividual Specifications
NTC Thermistors for Inrush Current Suppression
NT NTC Thermistors L
PA7
PAA
PAD
PAJ
PAN
±15%
BM
Individual Specifications
Product ID
Code
Code
Series
Resistance Tolerance
Code
(Global Part Number)
eResistance
Expressed by three figures. The unit is ohm (Ω). The first and second figures are signficant digits, and the third figure expresses the number of zeros which follow the two figures. If there is a decimal point, it is expressed by the capital letter "R". In this case, all figures are significant digits.
3R0
100
Ex.)
3Ω
10Ω
Code Resistance
Lead Style, others
yPackaging
A0
B0
Ammo Pack
Bulk
Code Packaging
Inrush CurrentSuppressionLead Type
7mm
10mm
13mm
18mm
22mm
Nominal Body Diameter
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
4
1. Zero-power Resistance of Thermistor : R
2. B-Constant
R=R0 expB (1/T-1/T0) ..............(1)R : Resistance in ambient temperature T (K)(K : absolute temperature)R0 : Resistance in ambient temperature T0 (K)B : B-constant of Thermistor
as (1) formulaB=Rn (R/R0) / (1/T-1/T0) ............(2)
3. Thermal Dissipation Constant
When spend electric power P (mW) in ambient temperature T1, if Thermistor's temperature rises T2, there is a formula as followsP=C (T2-T1) ..................(3)C : Thermal dissipation constant (mW/°C)Thermal dissipation constant change by dimensions, measure, measured condition etc.
4. Thermal Time Constant
Period in which Termistor's temperature will change 63.2% of its temperature difference from ambient temperature T0 (°C) to T1 (°C).
[Resistance vs. Temperature]
!Basic Characteristics
!Performance
[Thermal Time Constant]
Item
Resistance
Condition
It measures by zero-power in specified ambient temperature.
Rated Electric Power It shows necessary electric power that Thermistor's temperature rises 100˚C by self heating in ambient temperature 25˚C.
Permissive Operating Current It is possible to keep Thermistor's temperature rising max. 1˚C
Thermal DissipationConstant
It shows necessary electric power that Thermistor's temperature rises 1˚C by self heating.It calculates by next formula. (mW/˚C)
B-Constant
It calculates between two specified ambient temperature by next formula.T and T0 is absolute temperature (K).
Rn (R/R0)B =
1/TY1/T0
PC =
TYT0
102
101
Res
ista
nce
VS
. Tem
pera
ture
Cha
ract
eris
tics
[R/R
25]
−20Temperature [˚C]
0 20 40 60 80 12010010−2
10−1
1
B=3450B=3900B=4100
Basic Characteristics
T1
T0
Time
63.2%
X
Tem
pera
ture
Please inquire about test condition and Ratings.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
5
1NTC Thermistorsfor Temperature Compensation 0201(0603) Size
0201/0402/0603/0805 sized Chip NTC Thermistor have Ni barrier termination and provide excellent solderability and offer high stability in environment by unique inner construction.
Features1. Excellent solderability and high stability in environment.2. Excellent long time aging stability.3. High accuracy in resistance and B-constant.4. Reflow soldering possible.5. Lead is not contained in the product.
Applications• Temperature compensation of transistor, IC, crystal oscillator of mobile communications equipments.• Temperature sensor for rechargeable batteries.• Temperature compensation of LCD.• Temperature compensation and sensing of car audio equipments. (CD, MD, Tuner)• Temperature compensation of several kinds of circuits.
Electrode(Ag Alloy + Ni Plating + Sn Plating)
0.15±0.05 0.15±0.050.60±0.03
(in mm)
0.30
±0.0
30.
30±0
.03
Part NumberResistance
(25°C)(k ohm)
B-Constant(25-50°C)
(K)
Max. OperatingCurrent(25°C)
(mA)
Rated ElectricPower(25°C)
(mW)
Typical DissipationConstant(25°C)
(mW/°C)
OperatingTemperature Range
(°C)
NCP03XH103p05RD 10 3380 ±3% 0.31 100 1 -40 to 125
A blank column is filled with resistance tolerance codes. (J:±5%, K:±10%)
Standard Land Dimensions
Chip
a
a b c
c
b
Land
Solder Resist
Soldering Methods
Reflow Soldering
(in mm)
0.25 0.30.25
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
6
2
NTC Thermistorsfor Temperature Compensation 0402(1005) Size
0201/0402/0603/0805 sized Chip NTC Thermistor have Ni barrier termination and provide excellent solderability and offer high stability in environment by unique inner construction.
Features1. Excellent solderability and high stability in environment.2. Excellent long time aging stability.3. High accuracy in resistance and B-constant.4. Reflow soldering possible.5. Same B-constant in the same resistance in the three sizes. (0805 size / 0603 size / 0402 size) Easy to use smaller size in the circuits.6. Lead is not contained in the product.
Applications• Temperature compensation of transistor, IC, crystal oscillator of mobile communications equipments.• Temperature sensor for rechargeable batteries.• Temperature compensation of LCD.• Temperature compensation and sensing of car audio equipments. (CD, MD, Tuner)• Temperature compensation of several kinds of circuits.
Electrode(Ag Alloy + Ni Plating + Sn Plating)
0.25±0.10 0.25±0.101.0±0.05
(in mm)
0.5±
0.05
0.5±
0.05
Part NumberResistance
(25°C)
B-Constant(25-50°C)
(K)
Max. OperatingCurrent(25°C)
(mA)
Rated ElectricPower(25°C)
(mW)
Typical DissipationConstant(25°C)
(mW/°C)
OperatingTemperature Range
(°C)
NCP15XC220p03RC 22ohm 3100 ±3% 6.70 100 1 -40 to 125
NCP15XC330p03RC 33ohm 3100 ±3% 5.50 100 1 -40 to 125
NCP15XC470p03RC 47ohm 3100 ±3% 4.60 100 1 -40 to 125
NCP15XC680p03RC 68ohm 3100 ±3% 3.80 100 1 -40 to 125
NCP15XF101p03RC 100ohm 3250 ±3% 3.10 100 1 -40 to 125
NCP15XF151p03RC 150ohm 3250 ±3% 2.50 100 1 -40 to 125
NCP15XM221p03RC 220ohm 3500 ±3% 2.10 100 1 -40 to 125
NCP15XM331p03RC 330ohm 3500 ±3% 1.70 100 1 -40 to 125
NCP15XQ471p03RC 470ohm 3650 ±3% 1.40 100 1 -40 to 125
NCP15XQ681p03RC 680ohm 3650 ±3% 1.20 100 1 -40 to 125
NCP15XQ102p03RC 1.0k ohm 3650 ±3% 1.00 100 1 -40 to 125
NCP15XW152p03RC 1.5k ohm 3950 ±3% 0.81 100 1 -40 to 125
NCP15XW222p03RC 2.2k ohm 3950 ±3% 0.67 100 1 -40 to 125
NCP15XW332p03RC 3.3k ohm 3950 ±3% 0.55 100 1 -40 to 125
NCP15XM472p03RC 4.7k ohm 3500 ±3% 0.46 100 1 -40 to 125
NCP15XW682p03RC 6.8k ohm 3950 ±3% 0.38 100 1 -40 to 125
NCP15XH103p03RC 10k ohm 3380 ±3% 0.31 100 1 -40 to 125
NCP15XW153p03RC 15k ohm 3950 ±3% 0.25 100 1 -40 to 125
NCP15XW223p03RC 22k ohm 3950 ±3% 0.21 100 1 -40 to 125
NCP15WB333p03RC 33k ohm 4050 ±3% 0.17 100 1 -40 to 125
NCP15WB473p03RC 47k ohm 4050 ±3% 0.14 100 1 -40 to 125
NCP15WD683p03RC 68k ohm 4150 ±3% 0.12 100 1 -40 to 125
NCP15WF104p03RC 100k ohm 4250 ±3% 0.10 100 1 -40 to 125
NCP15WM154p03RC 150k ohm 4500 ±3% 0.08 100 1 -40 to 125
Continued on the following page.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
7
2
Part NumberResistance
(25°C)
B-Constant(25-50°C)
(K)
Max. OperatingCurrent(25°C)
(mA)
Rated ElectricPower(25°C)
(mW)
Typical DissipationConstant(25°C)
(mW/°C)
OperatingTemperature Range
(°C)
Continued from the preceding page.
NCP15WM224p03RC 220k ohm 4500 ±3% 0.06 100 1 -40 to 125
NCP15WM474p03RC 470k ohm 4500 ±3% 0.04 100 1 -40 to 125
A blank column is filled with resistance tolerance codes. (J:±5%, K:±10%)
Tolerance ±1% NCP15XH103F04RC is also availalbe for 10k ohm type.
Standard Land Dimensions
Chip
a
a b c
c
b
Land
Solder Resist
Soldering Methods
Reflow Soldering
(in mm)
0.4 0.50.4−0.5
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
8
3
NTC Thermistorsfor Temperature Compensation 0603(1608) Size
0201/0402/0603/0805 sized Chip NTC Thermistor have Ni barrier termination and provide excellent solderability and offer high stability in environment by unique inner construction.
Features1. Excellent solderability and high stability in environment.2. Excellent long time aging stability.3. High accuracy in resistance and B-constant.4. Flow / Reflow soldering possible5. Same B-constant in the same resistance in the three sizes. (0805 size / 0603 size / 0402 size) Easy to use smaller size in the circuits.6. Lead is not contained in the product.
Applications• Temperature compensation of transistor, IC, crystal oscillator of mobile communications equipments.• Temperature sensor for rechargeable batteries.• Temperature compensation of LCD.• Temperature compensation and sensing of car audio equipments. (CD, MD, Tuner)• Temperature compensation of several kinds of circuits.
Electrode(Ag Alloy + Ni Plating + Sn Plating)
0.2—0.6 0.2—0.61.6±0.15
(in mm)
0.8±
0.15
0.8±
0.15
Part NumberResistance
(25°C)
B-Constant(25-50°C)
(K)
Max. OperatingCurrent(25°C)
(mA)
Rated ElectricPower(25°C)
(mW)
Typical DissipationConstant(25°C)
(mW/°C)
OperatingTemperature Range
(°C)
NCP18XF101p03RB 100ohm 3250 ±3% 3.10 100 1 -40 to 125
NCP18XF151p03RB 150ohm 3250 ±3% 2.50 100 1 -40 to 125
NCP18XM221p03RB 220ohm 3500 ±3% 2.10 100 1 -40 to 125
NCP18XM331p03RB 330ohm 3500 ±3% 1.70 100 1 -40 to 125
NCP18XQ471p03RB 470ohm 3650 ±3% 1.40 100 1 -40 to 125
NCP18XQ681p03RB 680ohm 3650 ±3% 1.2 100 1 -40 to 125
NCP18XQ102p03RB 1.0k ohm 3650 ±3% 1.00 100 1 -40 to 125
NCP18XW152p03RB 1.5k ohm 3950 ±3% 0.81 100 1 -40 to 125
NCP18XW222p03RB 2.2k ohm 3950 ±3% 0.67 100 1 -40 to 125
NCP18XW332p03RB 3.3k ohm 3950 ±3% 0.55 100 1 -40 to 125
NCP18XM472p03RB 4.7k ohm 3500 ±3% 0.46 100 1 -40 to 125
NCP18XW682p03RB 6.8k ohm 3950 ±3% 0.38 100 1 -40 to 125
NCP18XH103p03RB 10k ohm 3380 ±3% 0.31 100 1 -40 to 125
NCP18XW153p03RB 15k ohm 3950 ±3% 0.25 100 1 -40 to 125
NCP18XW223p03RB 22.0k ohm 3950 ±3% 0.21 100 1 -40 to 125
NCP18WB333p03RB 33k ohm 4050 ±3% 0.17 100 1 -40 to 125
NCP18WB473p03RB 47k ohm 4050 ±3% 0.14 100 1 -40 to 125
NCP18WD683p03RB 68k ohm 4150 ±3% 0.12 100 1 -40 to 125
NCP18WF104p03RB 100k ohm 4250 ±3% 0.10 100 1 -40 to 125
NCP18WM154p03RB 150k ohm 4500 ±3% 0.08 100 1 -40 to 125
NCP18WM224p03RB 220k ohm 4500 ±3% 0.06 100 1 -40 to 125
NCP18WM474p03RB 470k ohm 4500 ±3% 0.04 100 1 -40 to 125
Both flow and reflow soldering methods can be employed.
A blank column is filled with resistance tolerance codes. (J:±5%, K:±10%)
Tolerance ±1% NCP18XH103F03RB is also availalbe for 10k ohm type.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
9
3
Standard Land Dimensions
Chip LandSolder Resist
b a
c
Soldering Methods a b c
Flow Soldering
Reflow Soldering
0.6~1.0
0.6~0.8
0.8~0.9
0.6~0.7
0.6~0.8
0.6~0.8
(in mm)
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
10
4
NTC Thermistorsfor Temperature Compensation 0805(2012) Size
0201/0402/0603/0805 sized Chip NTC Thermistor have Ni barrier termination and provide excellent solderability and offer high stability in environment by unique inner construction.
Features1. Excellent solderability and high stability in environment.2. Excellent long time aging stability.3. High accuracy in resistance and B-constant.4. Flow / Reflow soldering possible5. Same B-constant in the same resistance in the three sizes. (0805 size / 0603 size / 0402 size) Easy to use smaller size in the circuits.6. Lead is not contained in the product.
Applications• Temperature compensation of transistor, IC, crystal oscillator of mobile communications equipments.• Temperature sensor for rechargeable batteries.• Temperature compensation of LCD.• Temperature compensation and sensing of car audio equipments. (CD, MD, Tuner)• Temperature compensation of several kinds of circuits.
2.0±0.2
0.2—0.7 0.2—0.7
Electrode(Ag Alloy + Ni Plating + Sn Plating)
1.25
±0.2
0.85
±0.1
5
(in mm)
Part NumberResistance
(25°C)
B-Constant(25-50°C)
(K)
Max. OperatingCurrent(25°C)
(mA)
Rated ElectricPower(25°C)
(mW)
Typical DissipationConstant(25°C)
(mW/°C)
OperatingTemperature Range
(°C)
NCP21XM221p03RA 220ohm 3500 ±3% 3.00 200 2 -40 to 125
NCP21XQ471p03RA 470ohm 3650 ±3% 2.00 200 2 -40 to 125
NCP21XQ102p03RA 1.0k ohm 3650 ±3% 1.40 200 2 -40 to 125
NCP21XW222p03RA 2.2k ohm 3950 ±3% 0.90 200 2 -40 to 125
NCP21XM472p03RA 4.7k ohm 3500 ±3% 0.65 200 2 -40 to 125
NCP21XV103p03RA 10k ohm 3900 ±3% 0.44 200 2 -40 to 125
NCP21XW153p03RA 15k ohm 3950 ±3% 0.36 200 2 -40 to 125
NCP21XW223p03RA 22k ohm 3950 ±3% 0.30 200 2.0 -40 to 125
NCP21WB333p03RA 33k ohm 4050 ±3% 0.24 200 2.0 -40 to 125
NCP21WB473p03RA 47k ohm 4050 ±3% 0.20 200 2.0 -40 to 125
NCP21WF104p03RA 100k ohm 4250 ±3% 0.14 200 2.0 -40 to 125
Both flow and reflow soldering methods can be employed.
A blank column is filled with resistance tolerance codes. (J:±5%, K:±10%)
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
11
4
Standard Land Dimensions
Chip LandSolder Resist
b a
c
Soldering Methods a b c
Flow Soldering
Reflow Soldering
1.0~1.1
1.0~1.1
0.9~1.0
0.6~0.7
1.0~1.2
1.0~1.2
(in mm)
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
Temp.(°C)
Y40Y35Y30Y25Y20Y15Y10Y505101520253035404550556065707580859095100105110115120125
1588.39341220.8309947.2895740.9805584.6168465.2849373.0915301.4711245.1757200.3198164.7460136.3699113.517495.000079.061266.141455.609046.972639.856033.955929.046025.004121.615718.711316.252414.201812.453410.93859.63718.52127.55626.72656.00445.3842
1824.17481390.68511070.6526831.1384650.9600514.4408409.6997328.8767265.7593215.7848176.3948145.1611120.1519100.000083.668770.360759.456050.469743.028636.830331.648527.363623.756020.650618.010615.800113.908112.262510.84359.62238.56257.64826.84976.1618
2089.71831580.21051207.0558929.9356723.0199567.3679448.7753357.8766287.3508231.8627188.3951154.1328126.8562105.000088.323374.662063.410254.091546.337739.848234.397929.870826.042922.733919.909217.534315.493813.712312.170310.83869.67868.67447.79467.0340
2382.59011831.24641420.93431111.4707876.9252697.9274559.6372452.2066367.7635300.4797247.1190 204.5548170.2760142.5000118.591899.212283.413670.459059.784050.933843.569137.506232.423628.066924.378721.302618.680116.407814.455712.781911.334310.08979.00658.0763
2736.26222086.02761605.97901246.7076976.4400771.6612614.5496493.3150398.6389323.6772264.5922217.7417180.2278150.0000125.5030105.541189.184175.704564.542955.245547.472741.045335.634030.9759 27.0160 23.700120.862118.393716.265214.433512.843811.472310.27469.2426
3134.57752370.31581810.58371394.90341084.5298851.0519673.1630536.8150431.0262347.7940282.5927231.1992190.2843157.5000132.4850111.993095.115481.137269.506559.772351.596844.806239.064434.100829.863726.301423.240720.568418.255516.257814.517913.011611.691810.5510
4281.39103232.80282463.59871895.34061471.25031151.7079908.3588721.9176577.8973465.6678377.7788308.3256253.1370209.0000171.5071141.5184117.407797.882282.016169.042058.378849.572542.284936.212131.129626.858023.268120.227217.641615.446513.556211.941610.54959.3537
4947.90373703.75462798.87292135.88721645.03661278.03381000.6201789.6120627.7522502.4737405.0095328.4797268.0437220.0000181.5764150.6681125.6805105.335788.717275.058563.777154.414946.630940.114734.636730.012626.109922.790419.956517.541115.453113.662912.113910.7784
5703.88154232.70583171.82552400.94541834.75231414.67031099.4967861.4951680.2030540.8332433.1175349.0764283.1186231.0000191.7562160.0084134.1997113.073495.725981.395469.500359.581151.295144.326838.442533.453929.225625.614222.518719.870017.571515.593413.875412.3891
6422.08654849.20433695.39812843.01092206.87551727.56191362.53821082.8764866.8464698.5017566.6681462.4884379.7056313.5000257.2606212.2777176.1116146.8233123.0241103.562987.568374.358763.427454.318246.694440.287034.902130.340726.462423.169820.334317.912315.824314.0305
7421.85565555.63184198.30943203.83092467.55491917.05071500.93021184.4181941.6283753.7106607.5142492.7196402.0655330.0000272.3645226.0022188.5207158.0036133.0758112.587895.665681.622469.946460.172151.955045.018939.164934.185629.934726.311723.179720.494418.170816.1676
8555.82236349.05874757.73833601.41822752.12852122.00541649.24501292.24261020.3045811.2498649.6763523.6146424.6779346.5000287.6344240.0126201.2996169.6100143.5889122.0932104.250489.371776.942766.490357.663850.180843.838438.421333.778129.805023.357223.390020.813118.5837
NCP∗∗XF101J type NCP∗∗XF151J type NCP∗∗XM221J type NCP∗∗XM331J typeResistance (Ω)
Center HighLowResistance (Ω)
Center HighLowResistance (Ω)
Center HighLowResistance (Ω)
Center HighLow
1
Temp.(°C)
Y40Y35Y30Y25Y20Y15Y10Y505101520253035404550556065707580859095100105110115120125
10195.61937629.35485766.85834400.51403387.94632629.04532056.63471620.54981286.30771027.8581826.9792669.3557545.1310446.5000363.3735297.3779244.7447202.4473168.3307140.6799118.121599.624284.420671.836161.372152.663345.359939.235434.057529.663125.939422.755720.040717.7029
11822.47268767.74506570.22354971.78383796.93332923.39952269.59881775.22521399.05031110.2196887.2572713.4632577.3752470.0000384.8004316.7570262.1771218.0688182.2969153.1503129.2486109.550893.281179.749968.446358.996151.035944.331838.640333.790329.664226.122823.091320.4715
13674.640910050.80647466.78955603.17224244.65433242.58362498.35371939.80211517.87041196.1827949.5490758.5760609.9977493.5000406.4720336.5555280.1490234.3085196.9284166.3093141.0702120.1654102.814088.314276.145065.925157.278549.965143.730238.395633.839029.913126.539723.6139
14751.108711038.21548343.53966366.70124901.70963803.72512975.55662344.62531861.04101487.11391196.4806968.4295788.7002646.0000525.7319430.2488354.0986292.9025243.5424203.5369170.8993144.1371122.1404103.933188.793776.193865.627156.766149.274742.916937.529432.923228.995025.6127
17104.854012685.24809505.85527193.21915493.43554229.59933283.67492568.41092024.15791606.27521283.69131032.2446835.3513680.0000556.7325458.2867379.3200315.5038263.7488221.5791186.9979158.4991134.9600115.382899.028785.356073.839164.139755.905248.888142.918437.794733.408629.6183
19784.586814541.592310803.01468106.71726141.20194691.39753614.63942806.52222196.06791730.64731373.81561097.5142882.5499714.0000588.0872486.9313405.3220338.9995284.9176240.6177204.1015173.8563148.7522127.7737110.167395.380982.871072.289963.269355.551048.958643.278538.397934.1648
21.692816.232712.26999.36287.20845.59374.37583.44802.73682.18691.75951.42421.15990.95000.77310.63270.52070.43070.35820.29930.25130.21200.17960.15280.13060.11200.09650.08350.07250.06310.05520.04840.04260.0377
25.154218.654813.979210.57838.07866.22004.82893.77712.97672.36221.88781.51801.22851.00000.81870.67400.55780.46400.38790.32590.27500.23310.19850.16970.14560.12550.10860.09430.08220.07190.06310.05560.04910.0436
29.095021.384715.886811.92169.03126.89915.31564.12723.22952.54512.02031.61401.29791.05000.86480.71610.59610.49850.41900.35380.30010.25570.21880.18790.16200.14030.12190.10630.09300.08170.07200.06360.05650.0502
44.242032.071623.523617.445213.06479.88177.54455.81124.51223.53272.78562.21291.76991.42501.13960.91720.74280.60510.49580.40850.33830.28170.23550.19810.16720.14180.12080.10330.08880.07660.06630.05750.05020.0439
51.791237.172427.004819.842614.727811.04398.36176.38884.92213.82452.99362.36131.87561.50001.20740.97800.79690.65310.53820.44590.37130.31080.26130.22080.18730.15970.13670.11740.10130.08770.07630.06650.05820.0511
60.477042.976830.923622.513016.561112.31189.24427.00635.35574.13013.20922.51341.98261.57501.27601.04010.85280.70300.58280.48560.40660.34210.28910.24560.20940.17930.15420.13310.11530.10030.08760.07670.06740.0594
NCP**XQ471J type NCP∗∗XQ681J type NCP∗∗XQ102J type NCP∗∗XW152J typeResistance (Ω)
Center HighLowResistance (Ω)
Center HighLowResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLow
for Temperature Compensation Temperature Characteristics (Reference Value)
Continued on the following page.
for Temperature Compensation Temperature Characteristics (Reference Value)
12
4
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
Temp.(°C)
Y40Y35Y30Y25Y20Y15Y10Y505101520253035404550556065707580859095100105110115120125
64.888347.038334.501325.586319.161614.493211.06538.52306.61795.18134.08563.24562.59592.09001.67141.34531.08950.88750.72720.59910.49620.41310.34550.29050.24520.20800.17720.15160.13020.11230.09720.08440.07360.0644
75.960554.519539.607029.102521.600816.197712.26389.37027.21905.60934.39073.46332.75092.20001.77091.43441.16880.95780.78940.65400.54460.45590.38320.32290.27480.23420.20040.17220.14860.12870.11180.09750.08540.0750
88.699663.032645.354733.019024.289618.057313.558110.27597.85516.05754.70683.68632.90792.31001.87151.52561.25071.03110.85480.71220.59630.50180.42400.36020.30710.26300.22610.19520.16920.14710.12840.11240.09880.0871
97.332470.557551.751938.379528.742421.739816.597912.78469.92697.77196.12834.86843.89383.13502.50712.01791.63421.33131.09080.89870.74420.61970.51820.43570.36790.31210.26580.22730.19530.16840.14580.12660.11040.0966
113.940781.779359.410543.653732.401224.296518.395614.055410.82868.41406.58605.19494.12633.30002.65632.15161.75321.43671.18410.98110.81690.68380.57480.48580.41220.35130.30070.25830.22290.19300.16780.14630.12810.1125
133.049594.548968.032049.528536.434427.085920.337215.413811.78269.08637.06025.52944.36183.46502.80732.28831.87611.54671.28211.06830.89450.75270.63600.54030.46060.39450.33920.29280.25380.22070.19260.16870.14830.1307
91.466169.064452.631440.491431.431324.604719.405815.422812.34609.94848.07076.58705.40794.46503.66403.02332.50832.09111.75221.47501.24721.05900.90340.77360.66500.57380.49710.43210.37690.33000.28960.25510.22540.1998
105.705279.125759.794145.630335.144027.303421.376916.869013.411110.73478.65257.01755.72644.70003.87913.21882.68502.25041.89531.60351.36251.16250.99620.85700.74000.64120.55780.48690.42630.37470.33010.29190.25880.2303
121.855790.426067.761751.292939.197030.222523.489218.404714.531611.55429.25307.45756.04844.93504.09663.41842.86702.41572.04511.73891.48481.27291.09590.94700.82130.71470.62440.54720.48110.42450.37540.33310.29640.2647
200.5638145.3912106.640379.085059.226844.797234.201726.343920.455416.014912.628110.03198.02376.46005.16614.15823.36752.74322.24781.85181.53361.27691.06780.89790.75800.64300.54780.46850.40250.34700.30030.26080.22740.1990
234.7869168.5150122.421789.953166.766150.065537.906228.962622.313417.337913.571210.70468.50286.80005.47354.43353.61262.96052.44002.02161.68341.40911.18451.00100.84930.72390.61960.53230.45930.39780.34570.30150.26390.2318
274.1625194.8281140.1871102.058875.076955.813441.906931.761924.279418.723214.548211.39398.98807.14005.78484.71533.86593.18712.64202.20131.84311.55111.31061.11330.94920.81300.69900.60330.52290.45480.39690.34750.30550.2694
NCP∗∗XW222J type NCP∗∗XW332J type NCP∗∗XM472J type NCP∗∗XW682J typeResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLow
2
Temp.(°C)
Y40Y35Y30Y25Y20Y15Y10Y505101520253035404550556065707580859095100105110115120125
170.0056129.8266100.115677.938961.195748.462238.665331.039925.092520.430416.733713.780411.41169.50007.85526.52885.45314.57263.85023.25512.76242.35912.02301.74011.50221.30191.13220.98680.86270.75720.66650.58830.52060.4621
195.6520148.1710113.347187.558868.236753.6496.42.506233.892227.218622.021117.925514.673512.080510.00008.31456.94795.83364.91694.16093.53503.01432.58612.22751.92451.66851.45211.26801.10960.97380.85800.75800.67150.59640.5311
224.6043168.6845128.006598.120175.897559.243746.611736.914029.451123.676219.154215.585512.756710.50008.77877.37546.22525.27394.48543.82933.28092.82792.44672.12321.84861.61561.41651.24451.09650.96970.86000.76460.68150.6090
442.4201320.7159235.2360174.4523130.647398.817475.444958.111645.122235.327027.856122.129217.699314.250011.39599.17247.42836.05124.95834.08503.38292.81662.35541.98061.67211.41851.20831.03340.88780.76550.66250.57530.50170.4390
517.9122371.7242270.0479198.4259147.2781110.438583.616663.888049.220838.245329.936423.613118.756115.000012.07409.77997.96916.53065.38234.45933.71333.10822.61282.20821.87341.59691.36671.17411.01320.87750.76260.66500.58220.5113
604.7702429.7679309.2363225.1297165.6109123.117892.441770.062953.557441.301132.091625.133619.826415.750012.760510.40158.52787.03035.82794.85584.06573.42142.89112.45582.09381.79331.54191.33081.15341.00320.87560.76660.67390.5942
648.8828470.3834345.0129255.8634191.6160144.9322110.652585.230466.179251.813040.855532.456125.958920.900016.713913.452910.89498.87517.27225.99134.96164.13103.45462.90492.45242.08041.77221.51561.30211.12280.97170.84380.73590.6438
759.6046545.1955396.0702291.0246216.0079161.9765122.637793.702472.190556.093143.906734.632527.509022.000017.708514.343811.68809.57827.89406.54035.44624.55873.83213.23872.74772.34212.00441.72211.48601.28701.11850.97530.85390.7500
886.9963630.3263453.5466330.1902242.8960180.5728135.5811102.759078.550860.575047.067736.862629.078723.100018.715415.255512.507410.31118.54757.12195.96315.01814.24033.60183.07092.63022.26151.95181.69171.47141.28421.12440.98840.8715
1046.0404752.9420548.5400404.1776300.9970226.4171171.9353131.7346101.758779.244062.186849.158039.128331.350024.942119.969316.086913.034910.62078.69957.16205.92724.92854.11453.45142.90882.46002.08831.78051.52351.30711.12590.97380.8441
1227.2628874.4491630.8514460.4568339.7972253.3626190.7661144.9635111.086785.841766.861352.470141.470933.000026.430321.298317.265814.076111.53779.50587.87026.54945.47514.59503.87423.28152.78872.37872.03751.75131.50931.30581.13410.9872
1436.28151013.0257723.7003523.2611382.6399282.8061211.1301159.1220120.966792.756371.707455.865543.844034.650027.937222.658918.484915.162612.502610.36088.62697.21876.06725.11874.33793.69263.15342.70262.32582.00821.73841.51061.31761.1517
NCP∗∗XH103J type NCP∗∗XW153J type NCP∗∗XW223J type NCP∗∗WB333J typeResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLow
for Temperature Compensation Temperature Characteristics (Reference Value)
Continued from the preceding page.
Continued on the following page.
for Temperature Compensation Temperature Characteristics (Reference Value)
13
4
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
Temp.(°C)
Y40Y35Y30Y25Y20Y15Y10Y505101520253035404550556065707580859095100105110115120125
1489.81511072.3720781.2539575.6469428.6928322.4729244.8776187.6220144.9290112.862788.569170.012855.728144.650035.523628.441222.911618.564815.126412.390210.20058.44187.01945.86014.91564.14293.50362.97422.53582.16981.86161.60361.38691.2023
1747.91971245.4275898.4853655.8022483.9536360.8498271.6971206.4631158.2144122.259495.226774.730259.064747.000037.643130.333924.590720.047816.432513.538511.20919.32797.79796.54435.51784.67363.97173.38782.90192.49432.14961.85981.61531.4060
2045.61311442.79421030.7247745.2507544.9720402.7844300.7004226.6283172.2859132.1074102.128779.566062.444549.350039.789432.271826.327021.595217.806714.756312.286810.28118.64117.29026.17825.25914.49123.84923.31252.86022.47592.15141.87651.6403
2325.96311664.56041205.6590883.2052653.5386488.5367368.7125280.7073215.6355166.9555130.2753102.406881.061264.600051.108540.698032.609126.287921.307817.369514.233011.72119.70298.06576.73765.65224.76114.02883.41992.91562.49452.14151.84601.5950
2735.35931937.39071389.34451008.0144738.9776547.4555409.5999309.2166235.6064180.9801140.1394109.343785.928768.000054.166843.420535.015728.405623.165718.996715.656912.966910.79359.02067.57496.38725.40714.59783.92163.35892.88692.48942.15521.8701
3208.77192249.30201597.01231147.5848833.4974611.9463453.8837339.7697256.7833195.6923150.3734116.458690.860771.400057.264546.209237.505930.617325.122620.724417.180314.309211.976510.06348.49497.19976.12555.23414.48563.85993.33262.88652.50982.1871
3729.03802647.23361902.57551383.31821016.2022754.3293565.4664427.6799326.4567251.2051194.8470152.2795119.861495.000074.736559.187447.171137.830130.508724.747520.181716.542413.631911.28139.38307.83826.57525.54154.68553.97933.39182.90112.49182.1455
4397.11933088.59892197.22501581.88051151.0367846.5788628.9882471.6321357.0117272.4995209.7098162.6506127.0802100.000079.221663.167150.676640.903533.194627.090922.224318.322515.184112.635410.56578.87267.48116.33655.38394.59423.93423.38042.91642.5220
5171.92953594.54282531.16281804.42231300.5024947.7345697.8966518.8009389.4505294.8601225.1420173.2936134.3970105.000083.766067.245954.306644.116136.026729.582024.412620.243416.870914.116611.867810.01848.49057.22746.17095.29104.55203.92913.40482.9573
9772.54296837.32744847.69273474.96592517.29441843.90981363.44161017.7304766.4841582.1552445.6263343.7517267.1098209.0000162.2097126.735499.665178.877062.781050.265540.449432.743426.627621.757217.868314.739712.210810.16388.48797.12035.99505.06554.29833.6595
11585.88408016.97275623.93113990.10002861.78392076.16191520.90941125.0494839.9121632.5207480.1943367.4554283.3096220.0000172.0121135.3636107.198085.418668.441255.153344.664536.378729.762624.462320.205416.761413.961911.68369.80858.27036.99835.94235.06654.3338
13701.35979376.64206508.15384570.14433245.28292331.82351692.32231240.5760918.0736685.5255516.1503391.8117299.7408231.0000181.9509144.2178115.012092.271674.425260.365249.195540.316633.183627.435022.791119.012615.924213.397211.30629.58208.14906.95345.95705.1195
NCP∗∗WB473J type NCP∗∗WD683J type NCP∗∗WF104J type NCP∗∗WM224J typeResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLow
3
Temp.(°C)
Y40Y35Y30Y25Y20Y15Y10Y505101520253035404550556065707580859095100105110115120125
20877.705314607.017710356.43437423.79095377.85633939.26182912.80702174.24211637.48871243.6953952.0198734.3785570.6436446.5000346.5388270.7529212.9209168.5099134.1230107.385486.414769.951856.886346.481438.173231.489426.086721.713618.133315.211512.807510.82189.18287.8181
24751.661217127.168912014.76198524.30456113.81114435.43683249.21562403.51461794.35781351.29431025.8697785.0184605.2524470.0000367.4804289.1859229.0139182.4853146.2153117.827695.419777.718263.583852.260443.166235.808429.827724.960520.954517.668314.950812.694910.82399.2586
29271.086720031.917013903.78329763.49016933.10444981.62293615.41582650.32141961.33901464.53181102.6846837.0523640.3553493.5000388.7133308.1016245.7074197.1257158.9993128.9620105.099686.130970.892258.611148.690240.617934.020028.621224.154120.470617.409214.855012.726310.9371
188.0202142.7877109.522184.822766.269452.228341.476533.146226.678021.629417.643014.471211.93719.90008.21626.85345.74434.83334.08333.46342.94862.52592.17241.87411.62251.41011.22961.07460.94190.82880.73130.64710.57400.5106
195.6520148.1710113.347187.558868.236753.649642.506233.892227.218622.021117.925514.673512.080510.00008.31456.94795.83364.91694.16093.53503.01432.58612.22751.92451.66851.45211.26801.10960.97380.85800.75800.67150.59640.5311
203.5731153.7418117.294090.374170.255455.104043.557034.651527.767522.417518.210714.877212.224410.10008.41327.04305.92385.00154.23953.60763.08122.64762.28391.97611.71571.49521.30741.14561.00670.88810.78560.69680.61960.5524
NCP∗∗WM474J type NCP∗∗XH103F typeResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLow281.4484205.0766151.0349112.452684.637364.246149.263038.053629.651223.279818.415314.669811.76689.50007.61956.14974.99404.07893.35002.76682.29761.91761.60661.35461.14680.97490.83230.71370.61440.53090.46070.40120.35050.3075
328.9962237.3866173.1845127.773095.326771.745954.563841.813132.330125.193819.785415.650812.468310.00008.07236.55595.35624.40073.63503.01892.52062.11481.78101.50911.28381.09660.94050.81010.70050.60780.52970.46310.40620.3577
383.6153274.1001198.0859144.8177107.097779.920860.283845.829035.162927.197121.204416.655713.178610.50008.53056.97145.73034.73593.93443.28582.75842.32651.96941.67711.43361.23041.06010.91730.79660.69420.60740.53320.46950.4151
NCP21XV103J typeResistance (kΩ)
Center HighLow
for Temperature Compensation Temperature Characteristics (Reference Value)
Continued from the preceding page.
for Temperature Compensation Temperature Characteristics (Reference Value)
14
4
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
Chip Type !Caution/Notice
15
4
!Caution (Storage and Operating Conditions)This product is designed for the applications under ordinary environment(room temperature, normal humidity and atmospheric pressure). Do not use under the following environments. Because all these factors can deteriorate the characteristics of product or can cause the failures and the burning-out.1. Corrosive gas or deoxidizing gas. (Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.)
2. Volatile or flammable gas3. Dusty place4. Under vacuum, reducing pressure or under high- pressure5. Place with splashed water or under high humidity with dewing6. Place with salt water, oils, chemical liquids or organic solvents7. Place strongly vibrated8. Other place, where is similar like the above- mentioned environments
!Caution (Others)Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may becaused by the abnormal function or the failure of our product.
Notice (Storage and Operating Conditions)To keep solderability of product from declining, following storage condition is recommended.1. Storage condition : Temperature -10 to +40 degree C Humidity less than 75%RH (not dewing condition)2. Storage term : Use this product within 6 months after delivery by first-in and first-out stocking system.
3. Handling after unpacking : After unpacking, reseal promptly this product or store it in a sealed container with a drying agent.4. Storage place : Store this product in no corrosive gas (Sulfuric acid gas, Chlorine gas etc) nor directly under sunshine.
Notice (Rating)Use this product within the specified temperature range.Higher temperature may cause deterioration of the characteristics or the material quality of this product.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
Allowable Reflow Soldering Temperature and Time Standard Soldering Conditions
Allowable Reflow Soldering Temperature and Time Standard Soldering Conditions
Locate this product horizontal to the direction in which stress acts.
Keep this product on the PC Board away from the Separation Line. Worst ← A-B-C-D → Better
[Component Direction]
[Mounting Close to Board Separation Line]
A
B
D
CPerforationHoles
Slit
Mounting Position
Reflow Soldering Conditions (NCP03/NCP15 Series)
(NCP18/21 Series)
Flow Soldering Conditions (NCP18/21 Series)
Choose a mounting position that minimize the stress imposed on the chip during flexing or bending of the board.
Continued on the following page.
Allowable Reflow Soldering Temperature and Time Standard Soldering Conditions
Time (sec.)
Tem
pera
ture
(°C
)
Tem
pera
ture
(°C
)
280
270
260
250
240
230
220
2100 10 20 30
Preheating (in air) SolderingGradual cooling
(in air)300
200
100
01min. - 2min. 10sec. max.
Preheating : 160°C±10°C, 1~ 2min.Soldering : 230~260°C, 10sec. max.
Time (sec.)
Tem
pera
ture
(°C
)
280
270
260
250
240
230
220
2100 1109020 30 40 50 60 70 1008010
Tem
pera
ture
(°C
)
Preheating (in air) SolderingGradual cooling
(in air)300
200
100
01~ 2min. 20sec. max.
Preheating : 160°C±10°C, 1~ 2min.Soldering : 230~270°C, 20sec. max.
Time (sec.)
Tem
pera
ture
(°C
)
280
270
260
250
240
230
2200 9020 30 40 50 60 70 8010
Tem
pera
ture
(°C
)
Preheating (in air) SolderingGradual cooling
(in air)300
200
100
01~2min. 20sec. max.
Preheating : 160°C±10°C, 1~ 2min.Soldering : 240~270°C, 20sec. max.
1
Notice (Soldering and Mounting)Chip Type !Caution/Notice
16
4
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
For removing the flux after soldering, observe the following points in order to avoid deterioration of the characteristics or any change of the external electrodes quality.
Thin or insufficient adhesive may have components a loose contact with land, during flow soldering.Low viscosity adhesive causes chips to slip after mounting.
(1) Reflow Soldering : NCP03/15/18/21 SeriesUse RA/RMA type or equivalent type of solder paste for your reference, we are using solder paste, manufactured by SENJI METAL INDUSTRY CO., LTD, for any internal tests of this product.•SPT-70-0F-2063 (Sn:Pb:Ag = 63:35:2wt%)•M31-221CM5 (Sn:Ag:Cu = 95.8:3.5:0.7wt%)•M42-381F4-11 (Sn:Ag:Bi:Cu = 94.3:2.0:3.0:0.7wt%)
(2) Flow Soldering : NCP18/21 SeriesWe are using below solder paste for any internal teats of this product.•Sn : Pb=63wt%:37wt%•Sn : Ag : Cu=95.8wt% : 3.5wt% : 0.7wt%•Sn : Ag : Bi : Cu=94.3wt% : 2.0wt% : 3.0wt% : 0.7wt%
NCP03/15 NCP18/21
NCP03
NCP15
NCP18/NCP21
0.06mg
0.2mg
1.0mg
150µm
150µm
200µm
1/3EVTVE
1/3EVTVE
0.2mmVTVE
∗ The land side
The amount of solder paste ∗Part Number The solder paste thickness T
Reference : Optimum Solder Amount
TE
electrode
solder solder
Continued from the preceding page.
Solder and Flux
Cleaning Conditions
After cleaning, dry promptly this product. Drying
The amount of solder is critical. Standard height of fillet is show in the table below.Too much solder gives too strong mechanical stress to this product, such stress may cause cracking, any mechanical and electronical damage.
Printing Conditions of Solder Paste
Adhesive Application and Curing
1. Solder and Paste
Use Rosin-based flux.Do not use strong acidic flux (with halide content exceeding 0.2wt%)
2. Flux
Isopropyl Alcohol
Less than 5min. at room
temp. or Less than
2min. at 40°C max.
Less than 5min. 20W/r
Frequency of 28kHz to
40kHz.
Isopropyl Alcohol
Less than 5min. at room
temp. or Less than
2min. at 40°C max.
Less than 1min. 20W/r
Frequency of several
10kHz to several 100kHz.
Solvent
Dipping Cleaning
Ultrasonic Cleaning
2
Chip Type !Caution/Notice
17
4
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
NCP03
NCP15
NCP18
NCP21
15000
10000
4000
-
-
4000
Part NumberPaper Tape
Quantity (pcs.)
Plastic Tape
Packaging Code RA RC RD RB
Packaging Tape Plastic Taping2mm pitch 4mm pitch
Paper Taping
(in mm)
(in mm)
40min.190-250
Vacant sevtion
210-250
Top tape aloneCover tape alone
Leader unit
Trailer unit
Chip-mounting unit
Direction of feed
ø178±2.0
ø21.0±0.8
ø13.0±0.5
ø50
min
.
2.0±0.5
10.0±1.52.0±0.5
(1) A tape in a reel contains Leader unit and Trailer unit where
products are not packed. (Please refer the figure right.)
(2) The top and base tapes or, plastic and cover tape are not
sticked at the first five pitches minimum.
(3) A label shall be attached on the reel. (MURATA's part
number, inspection number and quantity shall be marked on
the label.)
(4) Taping reels shall be packed in a package.
1. Dimensions of Reel
2. Taping Method
Tape Carrier Packaging
Packaging Code
Minimum Quantity Guide
Continued on the following page.
1
Chip Type Package
18
4
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
(1) Other Conditions
q Packaging
Products shall be packaged in the cavity of the base tape
and sealed by top tape and bottom tape.
w Tape
Top tape and bottom tape have no joints and products
shall be packaged and sealed in the cavity of the base
tape, continuously.
(2) Peeling force of top tape
(1) Other Conditions
q Packaging
Products shall be packaged in the each embossed cavity
of plastic tape and sealed by cover tape.
w Tape
Cover tape has no joints.
(3) Pull Strength
Pull strength of top tape shall be specified 10N minimum.
Pull strength of bottom tape shall be specified 5N minimum.
3. Paper Tape
4. Plastic tape
8mm width 2mm pitch Tape
Part Number A
NCP03
NCP15
0.37∗
0.65∗
B
0.67∗
1.15∗
C
0.4 max.
0.8 max.
Part Number A
NCP18 1.05∗B
1.85∗C
1.1 max.
8mm width 4mm pitch Tape
C4.0±0.1 4.0±0.12.0±0.05
ø1.5+0.1/–0
1.75
±0.1
3.5±
0.05
8.0±
0.3
Direction of feed
A
C4.0±0.12.0±0.05
ø1.5+0.1/–0 1.75
±0.1
3.5±
0.05
B 8.0±
0.3
Direction of feed
A
(in mm)
∗ Reference value
∗ Reference value
165-180 ° F
∗ 1 Peeling angle : 165 to 180 degree against the fixed surface of tape.
∗ 2 Peeling speed : 300mm/min.
∗ 3 Peeling force : 0.1N - 0.6N
Continued on the following page.
Continued from the preceding page.
1.050.2
4.0±0.12.0±0.05
4.0±0.1 φ1.5
1.75
±0.1
φ1.0 1.45
3.5±
0.05
8.0±
0.3
Direction of feed
2.25
(in mm)
B
+0.3-0
+0.1-1
2
Chip Type Package
19
4
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
∗ 1 Peeling angle : 165 to 180 degree against the fixed surface of tape.
∗ 2 Peeling speed : 300mm/min.
∗ 3 Peeling force : 0.1N - 0.7N
F165-180 °
Continued from the preceding page.
(2) Peeling force of cover tape
(3) Tape Strength
Pull strength of plastic tape and cover tape shall be specified
10N minimum.
3
Chip Type Package
20
4
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
21
5
NTC Thermistorsfor Temperature Sensor Resin Coated Radial Lead Type
This product is sensor type NTC Thermistor to be useful in the normal temperature range developed by the unique ceramic technology and the automatic assembly.
Features1. High-accuracy of +-1% +-1% of resistance and B-Constant tolerance is realized due to uniform thickness by the precise sheet forming method.2. Quick response This product provides faster response time due to its smaller size.3. Taping type is available(Standard type)4. Strong lead strength Original lead-wiring technique assures reliable connection. It can be formed and bent flexibly according to the mounting condition.5. Lead Coating type The lead wires of Lead Coating type are coated with strong and flexible resin.
Applications• Rechargeable batteries• Battery charging circuits• Head of printers• DC fan motors• Home appliance equipments
Solder Plated Copper Ply Wireφ0.4±0.03
31±1
2.5±1.0
6.0m
ax.
3.3max. 2.5max.
Epoxy Resin
(in mm)
NTSA0 Series
Solder Plated Copper Ply Wireφ0.4±0.03
31±1
2.5±1.0
6.0m
ax.
3.0max. 1.6max.
Epoxy Resin
(in mm)
NTSA0XH103_E1B0
Part NumberResistance
(25°C)(k ohm)
B-Constant(25-50°C)
(K)
Max. OperatingCurrent(25°C)
(mA)
Rated ElectricPower(25°C)
(mW)
Typical DissipationConstant(25°C)
(mW/°C)
Thermal TimeConstant(25°C)(s)
OperatingTemperature Range
(°C)
NTSA0XM202pE1B0 2.0 3500 ±1% 1.05 21 2.1 less than7 -40 to 125
NTSA0XR502pE1B0 5.0 3700 ±1% 0.68 21 2.1 less than7 -40 to 125
NTSA0XH103pE1B0 10 3380 ±1% 0.38 15 1.5 less than7 -40 to 125
NTSA0XV103pE1B0 10 3900 ±1% 0.46 21 2.1 less than7 -40 to 125
NTSA0WB203pE1B0 20 4050 ±1% 0.31 21 2.1 less than7 -40 to 125
NTSA0WC303pE1B0 30 4100 ±1% 0.26 21 2.1 less than7 -40 to 125
NTSA0WD503pE1B0 50 4150 ±1% 0.20 21 2.1 less than7 -40 to 125
NTSA0WF104pE1B0 100 4250 ±1% 0.14 21 2.1 less than7 -40 to 125
A blank column is filled with resistance tolerance codes. (F:±1%, E:±3%)
Taping type of part numbers with "N6A0" is available.(Lead spacing=5mm)
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the "Package" page.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
22
5
Lead-Coating Type
Features1. Electric insuration on lead wire.2. Excellent bending resistant due to flexible resin.3. Easy handring due to most suitable hardness of surface of coating.4. Measurement accuracy of +-1 (degree C) or less in the range from -40 to +70 (degree C).
3.0 max.
0.60-0.952.5
+1.5−0.5
2.0 max.
φ0.4±0.03
(Solder PlatedCopper Plywire)
(in mm)
5±1
27.0
±2.0
3±1.
5
(Coa
ting
Are
a)
NTSD0XH103FE1B0
3.8 max.
0.60-0.952.5
+1.5−0.5
2.5 max.
φ0.4±0.03
(Solder PlatedCopper Plywire)
(in mm)
5±1
27.0
±2.0
3±1.
5
(Coa
ting
Are
a)
NTSD0WF104FE1B0
Part NumberResistance
(25°C)(k ohm)
B-Constant(25-50°C)
(K)
Max. OperatingCurrent(25°C)
(mA)
Rated ElectricPower(25°C)
(mW)
Typical DissipationConstant(25°C)
(mW/°C)
Thermal TimeConstant(s)
OperatingTemperature Range
(°C)
NTSD0XH103FE1B0 10 ±1% 3380 ±1% 0.38 15 1.5 less than7 -40 to 125
NTSD0WF104FE1B0 100 ±1% 4250 ±1% 0.14 21 2.1 less than7 -40 to 125
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the "Package" page.
Temperature Tolerance-Temperature CharacteristicsResistance Tolerance +/-1% at 25degree C
Tem
pera
ture
Tol
eran
ce [±
˚C]
-40 125Temperature [˚C]
0 50 100
1.0
2.0
3.0
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
Temp.(°C)
Y40Y35Y30Y25Y20Y15Y10Y505101520253035404550556065707580859095100105110115120125
42.85932.24924.50418.77714.51611.3278.9067.0355.6004.4893.6232.9462.4091.9801.6321.3521.1260.9420.7920.6700.5690.4850.4150.3580.3090.2680.2330.2030.1780.1560.1370.1210.1070.096
44.65733.50525.38819.40214.96111.6449.1337.1985.7164.5713.6822.9872.4372.0001.6511.3711.1430.9580.8070.6830.5820.4970.4260.3670.3180.2760.2400.2100.1830.1610.1420.1250.1110.099
46.52634.80726.30220.04615.41711.9699.3657.3635.8344.6553.7413.0292.4662.0201.6711.3891.1610.9740.8220.6970.5940.5080.4360.3770.3260.2840.2470.2160.1890.1660.1470.1300.1150.103
118.39088.74767.12751.11239.24630.40023.71818.71014.83111.7419.3657.5266.0864.9504.0343.3082.7292.2591.8771.5731.3251.1210.9530.8110.6930.5940.5100.4410.3830.3330.2910.2550.2230.197
123.48492.29569.61452.86040.48031.27524.33919.15415.14811.9649.5207.6246.1605.0004.0823.3542.7732.2991.9141.6071.3561.1490.9780.8340.7140.6120.5270.4560.3960.3450.3020.2640.2320.205
128.78195.97572.18554.66241.74832.17224.97519.60715.46912.1899.6777.7426.2345.0504.1313.4012.8162.3401.9521.6411.3871.1771.0030.8570.7340.6310.5440.4710.4100.3580.3130.2750.2410.213
188.021142.788109.52284.82366.27052.22941.47733.14726.67821.63017.64314.47211.9389.9008.2176.8545.7454.8344.0843.4642.9492.5262.1731.8751.6231.4111.2301.0750.9420.8290.7320.6470.5740.511
195.652148.171113.34787.55968.23753.65042.50633.89227.21922.02117.92614.67412.08110.0008.3156.9485.8344.9174.1613.5353.0142.5862.2281.9251.6691.4521.2681.1100.9740.8580.7580.6710.5960.531
203.573153.741117.29490.37470.25555.10443.55734.65127.76722.41718.21014.87712.22410.1008.4137.0435.9235.0014.2393.6073.0812.6472.2831.9761.7151.4951.3071.1451.0060.8880.7850.6960.6190.552
332.325238.323173.098127.19194.52470.96253.82041.23731.87824.83919.51415.45312.3269.9007.9716.4595.2674.3203.5632.9542.4622.0621.7361.4671.2451.0610.9080.7810.6740.5830.5070.4420.3860.339
347.808248.591179.973131.83297.67973.11955.30142.25732.58225.32419.84715.67912.47810.0008.0686.5525.3534.3993.6353.0202.5212.1151.7831.5101.2841.0960.9390.8080.6980.6050.5270.4600.4030.354
363.977259.275187.102136.629100.93075.33456.81743.29933.29825.81520.18315.90712.63010.1008.1666.6455.4404.4793.7083.0862.5822.1701.8321.5531.3231.1310.9710.8370.7240.6280.5470.4790.4200.369
NTSA0XM202F type NTSA0XR502F type NTSA0XH103F type NTSA0XV103F typeResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLow
1
Temp.(°C)
Y40Y35Y30Y25Y20Y15Y10Y505101520253035404550556065707580859095100105110115120125
700.008502.881365.460267.924198.531149.036112.85585.96066.03951.15439.92731.38224.84319.80015.81912.71810.2868.3716.8515.6434.6743.8893.2512.7272.2981.9551.6711.4241.2171.0440.8980.7790.6790.590
733.007524.831380.184277.845205.260153.642116.01688.12567.52252.16840.61731.84725.15120.00016.01412.90210.4578.5276.9935.7714.7893.9923.3432.8092.3712.0201.7291.4761.2641.0850.9350.8120.7080.617
767.485547.685395.462288.106212.196158.374119.25490.33669.03253.19741.31432.31525.46120.20016.21013.08810.6308.6867.1375.9014.9064.0973.4372.8932.4462.0871.7891.5291.3121.1280.9730.8470.7390.644
1097.262785.054568.281415.020306.393229.194172.958131.298100.54277.63560.41147.34237.36929.70023.66318.97215.30412.42310.1428.3346.8875.7174.7693.9923.3562.8492.4302.0671.7641.5101.2971.1230.9760.846
1149.500819.651591.391430.529316.870236.337177.842134.630102.81679.18361.46048.04537.83430.00023.95519.24915.56012.65710.3548.5257.0585.8694.9054.1133.4632.9452.5162.1431.8321.5711.3501.1711.0190.886
1204.104855.688615.380446.573327.672243.678182.864138.033105.13180.75562.52148.75438.30030.30024.24019.52815.81912.89410.5698.7197.2326.0255.0444.2373.5743.0442.6052.2221.9031.6331.4071.2221.0650.927
1859.7091328.527960.265702.528519.195387.052291.216220.570168.570130.250101.32279.24862.42349.50039.33831.45825.30820.48916.68313.61511.1599.2367.6846.4175.3834.5313.8293.2502.7702.3682.0321.7511.5141.312
1948.5751387.289999.456728.895537.039399.167299.469226.186172.393132.857103.08980.43063.20150.00039.82531.91825.73320.87717.03413.92911.4399.4857.9066.6145.5584.6863.9673.3732.8782.4652.1181.8281.5831.374
2041.4841448.5061040.143756.177555.440411.621307.927231.921176.285135.503104.87581.62163.98250.50040.31532.38226.16321.27017.39014.24911.7259.7418.1336.8165.7384.8464.1093.4992.9912.5652.2071.9081.6551.438
4059.0352876.2612062.7761497.8001098.895813.431607.840457.312347.243266.643206.172160.304125.54599.00078.24062.23249.80340.11632.50326.39621.53117.74014.69312.21710.2058.5547.2006.0885.1674.4013.7623.2312.7851.438
4256.7523005.8882148.5141555.0201137.312839.314625.338469.127355.224272.045209.803162.713127.117100.00079.21563.15050.64940.88533.19527.01422.07918.22615.1242.598
10.5428.8527.4636.3215.3744.5853.9253.3762.9132.520
4463.6543141.0422237.5911614.2641176.955865.934643.275481.198363.353277.529213.477165.141128.696101.00080.19364.07551.50541.66433.89827.64322.63918.72415.56612.99010.8909.1607.7366.5625.5884.7754.0943.5273.0482.640
NTSA0WB203F type NTSA0WC303F type NTSA0WD503F type NTSA0WF104F typeResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLowResistance (kΩ)
Center HighLow
for Temperature Sensor Temperature Characteristics (Reference Value)for Temperature Sensor Temperature Characteristics (Reference Value)
23
5
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
for Temperature Sensor Lead Type !Caution/Notice
24
5
!Caution (Storage and Operating Conditions)This product is designed for the applications under ordinary environment(room temperature, normal humidity and atmospheric pressure). Do not use under the following environments. Because all these factors can deteriorate the characteristics of product or can cause the failures and the burning-out.1. Corrosive gas or deoxidizing gas. (Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.)
2. Volatile or flammable gas3. Dusty place4. Under vacuum, reducing pressure or under high- pressure5. Place with splashed water or under high humidity with dewing6. Place with salt water, oils, chemical liquids or organic solvents7. Place strongly vibrated8. Other place, where is similar like the above- mentioned environments
!Caution (Others)Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may becaused by the abnormal function or the failure of our product.
Notice (Rating)Use this product within the specified temperature range.Higher temperature may cause deterioration of the characteristics or the material quality of this product.
Notice (Storage and Operating Conditions)To keep solderability of product from declining, following storage condition is recommended.1. Storage condition : Temperature -10 to +40 degree C Humidity less than 75%RH (not dewing condition)2. Storage term : Use this product within 6 months after delivery by first-in and first-out stocking system.
3. Handling after unpacking : After unpacking, reseal promptly this product or store it in a sealed container with a drying agent.4. Storage place : Store this product in no corrosive gas (Sulfuric acid gas, Chlorine gas etc) nor directly under sunshine.
Notice (Soldering and Mounting)1. Be sure that the preheat-up does not melt the soldering of this product. Excessive heat may cause failures of open, short or insulation break down.2. Do not touch the body by soldering iron. The soldering point shall be min. 5 mm away from the root of lead wire.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
for Temperature Sensor Lead Type !Caution/Notice
25
5
Notice (Handling)1. The ceramic element of this product is fragile, and care must be taken not to load a excessive press-force or not to give a shock at handling. Such forces may cause cracking or chipping.2. Do not apply an excessive force to the lead. Otherwise, it may cause break off of junction between lead and element, or may crack element. Therefore, hold of element side lead wire is recommended when lead wire is bent or cut.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
for Temperature Sensor Lead Type NTSA0/NTSD0 Series Package
26
5 Item Coad Dimension (mm)
Pitch of Component
Pitch of Sprocket Hole
Lead Spacing
Lead Length from Hole Center to Component Center
Lead Length from Hole Center to Lead
Body Diameter
Deviation along Tape, Left or Right
Carrier Tape Width
Position of Sprocket Hole
Lead Distance between Reference and Bottom Planes
Height of Component
Overflow of Lead
Diameter of Sprocket Hole
Lead Diameter
Total Tape Thickness
Total Thickness, Tape and Lead Wire
Deviation across Tape
Portion to Cut in Case of Defect
Hole Down Tape Width
Hole Down Tape Position
Coating Extension on Lead
Thickness
P
P0
F
P2
P1
D
∆S
W
W1
H0
H2
I
D0
d
t1
t2
∆h1, ∆h2
L
W0
W2
e
T
12.7
12.7±0.3
5.0+0.8/–0.2
6.35±1.3
3.85±0.8
3.5 max.
0±2.0
18.0±0.5
9.0±0.5
16.0±1.0
4.0 max.
+0.5 to –1.0
4.0±0.1
0.50±0.03
0.6±0.3
1.6 max.
1.0 max.
11.0+0/–2.0
11.0 min.
1.5±1.5
Up to the crimp point
2.6 max.
(in mm)
Minimum Quantity
Taping Dimension
P2
P0I
L
P ∆S
H2
W2
W0
H0W1
W
t2 t1
∆h2 ∆h1
T
øD0
D
P1 ød
F
e
Part NumberAmmo Pack
Minimum Quantity (pcs.)
Bulk
NTSA0 3000 100
NTSD0 - 100
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
27
6
NTC Thermistorsfor Inrush Current Suppression Lead Type
This product effectively suppress surge current which are generated when switching power regulators or similar switches are turned on.
Features1. Lead type thermistors occupy a very small area and allow high-density packaging.2. Most suitable for power supplies of less than 100W.3. Excellent recovery characteristics due to resin coating with excellent heat characteristics.4. Highly reliable.
Applications• Switching power supplies • CRT monitors• Color televisions • VCR-Power supplies• Other power circuits
Coating Extensionon Lead : to line A
10.0
max
.3.
5±1.
0
NTPAN : 23.0 max.NTPAJ : 20.0 max. 5.5 max.
10.0±1.5
ø0.8±0.05Sn plated Cu wire
A
(in mm)
Coating Extensionon Lead : to line A
10.0
max
.3.
5±1.
0
NTPAD : 16.0 max.NTPAA : 12.0 max.
5.5 max.5.0 max.
7.5±1.5
ø0.8±0.05Sn plated Cu wire
A
(in mm)
NTPAD/NTPAA Series
NTPAN/NTPAJ Series
Coating Extensionon Lead : to line A
6.0
max
.3.
5±1.
0
NTPA7 : 9.0 max. 5.0 max.
5.0±1.5
ø0.6±0.05Sn plated Cu wire
A
(in mm)NTPA7 Series
Part NumberResistance
(25°C)(ohm)
Permissible Max.Current(25°C)
(A)
Permissible Max.Current(55°C)
(A)
Thermal TimeConstant(25°C)
(s)
Thermal DissipationConstant(mW/°C)
PermissibleElectrolytic Capacitor
(µF)
NTPAN3R0LDKB0 3.0 ±15% 5.4 4.7 135 26.8 8600 at 100V
NTPAN4R0LDKB0 4.0 ±15% 4.7 4.1 130 26.8 8600 at 100V
NTPAN6R0LDKB0 6.0 ±15% 3.9 3.4 130 26.8 8600 at 100V
NTPAJ4R0LDKB0 4.0 ±15% 4.0 3.5 125 21.8 5000 at 100V
NTPAJ6R0LDKB0 6.0 ±15% 3.4 2.9 125 21.8 5000 at 100V
NTPAJ8R0LDKB0 8.0 ±15% 3.0 2.6 130 21.8 5000 at 100V
NTPAJ100LDKB0 10.0 ±15% 2.6 2.2 130 21.8 5000 at 100V
NTPAD3R9LDNB0 3.9 ±15% 3.3 2.9 65 18.2 2700 at 100V
NTPAD5R1LDNB0 5.1 ±15% 3.0 2.6 85 18.8 2700 at 100V
NTPAD8R0LDNB0 8.0 ±15% 2.7 2.3 65 18.7 2700 at 100V
NTPAD160LDNB0 16.0 ±15% 2.0 1.7 100 19.1 2700 at 100V
NTPAA2R2LDNB0 2.2 ±15% 3.7 3.2 70 13.5 1400 at 100V
Continued on the following page.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
28
6
Part NumberResistance
(25°C)(ohm)
Permissible Max.Current(25°C)
(A)
Permissible Max.Current(55°C)
(A)
Thermal DissipationConstant(mW/°C)
PermissibleElectrolytic Capacitor
(µF)
Continued from the preceding page.
NTPAA3R9LDNB0 3.9 ±15% 2.7 2.3 70 13.5 1400 at 100V
NTPAA5R1LDNB0 5.1 ±15% 2.5 2.2 70 13.5 1400 at 100V
NTPAA8R2LDNB0 8.2 ±15% 2.0 1.7 70 13.5 1400 at 100V
NTPA74R0LBMB0 4.0 ±15% 2.3 2.0 40 9.4 700 at 100V
NTPA78R0LBMB0 8.0 ±15% 1.7 1.5 40 9.5 570 at 100V
NTPA7160LBMB0 16.0 ±15% 1.2 1.0 40 9.9 400 at 100V
NTPA7220LBMB0 22.0 ±15% 1.0 0.88 40 9.1 400 at 100V
NTPAD/NTPAA/NTPA7 series are also availabe on tape.
The order quantity should be an integral multiple of the "Minimum Quantity" shown in the "Package" page.
Application Circuit
NTC
−t˚
−
+
Determination of Allowable Current
Max
. cur
rent
rat
io
1.0
0
0.5
Ambient temperature [˚C]20 40 60 80 100 120 140 160
Thermal TimeConstant(25°C)
(s)
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
Current-R Ratio (RT/R25) / Current-Temperature Characteristics (Typical)
29
6
NTPAN3R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAN4R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAN6R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAJ4R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAJ6R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAJ8R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
Continued on the following page.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
Current-R Ratio (RT/R25) / Current-Temperature Characteristics (Typical)
30
6
Continued from the preceding page.
NTPAJ100L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAD3R9L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAD5R1L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAD8R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAD160L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAA2R2L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
Continued on the following page.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
Current-R Ratio (RT/R25) / Current-Temperature Characteristics (Typical)
31
6
Continued from the preceding page.
NTPAA3R9L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAA5R1L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPAA8R2L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPA74R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPA78R0L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
NTPA7160L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
Continued on the following page.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
Current-R Ratio (RT/R25) / Current-Temperature Characteristics (Typical)
32
6
Continued from the preceding page.
NTPA7220L Type
0.01 0.1
Current (A)
Ta=25˚C
1 10
Resistance RatioThermistor's Temperature (˚C)
10
1
0.1
0.01
1000
100
10
1
Res
ista
nce
Rat
io (
Rt/R
25)
The
rmis
tor's
Tem
pera
ture
(˚C
)
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
for Inrush Current Suppression Lead Type !Caution / Notice
33
6
!Caution (Storage and Operating Conditions)1. This product is designed for the Switching Power Supply with smoothing capacitors. Other application of this product may result to catch fire in the worst case.2. Use this product within the specified maximum current. Otherwise it may catch fire in the worst case.3. Use this product with smoothing capacitor within the specified maximum capacitance value. Otherwise it may catch fire in the worst case.4. This product is designed for the applications under ordinary environment (room temperature, normal humidity and atmospheric pressure). Do not use under the following environments. Because all these factors can deteriorate the
characteristics of product or can cause the failures and the burning-out. (1) Corrosive gas or deoxidizing gas. (Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) Volatile or flammable gas (3) Dusty place (4) Under vacuum, reducing pressure or under high-pressure (5) Place with splashed water or under high humidity with dewing (6) Place with salt water, oils, chemical liquids or organic solvents (7) Place strongly vibrated (8) Other place, where is similar like the above-mentioned environments
!Caution (Others)Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may becaused by the abnormal function or the failure of our product.
Notice (Storage and Operating Conditions)To keep solderability of product from declining, following storage condition is recommended.1. Storage condition : Temperature -10 to +40 degree C Humidity less than 75%RH (not dewing condition)2. Storage term : Use this product within 6 months after delivery by first-in and first-out stocking system.
3. Handling after unpacking : After unpacking, reseal promptly this product or store it in a sealed container with a drying agent.4. Storage place : Store this product in no corrosive gas (Sulfuric acid gas, Chlorine gas etc) nor directly under sunshine.
Notice (Rating)Use this product within the specified temperature range.Higher temperature may cause deterioration of the characteristics or the material quality of this product.
Notice (Soldering and Mounting)1. Be sure that the preheat-up does not melt the soldering of this product. Excessive heat may cause failures of open, short or insulation break down.2. Do not touch the body by soldering iron. The soldering point shall be min. 5 mm away from the root of lead wire.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
for Inrush Current Suppression Lead Type !Caution / Notice
34
6
Notice (Handling)1. When this product is operated, temperature of some area may be about 160(degree C). Use proper surrounding parts and material which withstand such temperature. If they are inadequate and kept at high temperature for long time, they may be deteriorated or may produce harmful gas. And, such harmful gas may deteriorate the element of this product.2. The ceramic element of this product is fragile, and
care must be taken not to load an excessive press-force or not to give a shock at handling. Such forces may cause cracking or chipping to the element.3. Do not apply an excessive force to the lead wire. Otherwise, it may cause break off junction between lead wire and element, or may crack element. So, fix lead wire of element side when lead wire is bent or cut.
Notice (Others)1. This products need sufficient cool off time to recover high resistance. Repeated ON-OFF may cause over specified current rating. Make sure inrush current do not exceed the specified ratings even at the worst condition. (maximum abient temperature and the shortest off time.)2. The resin coating of this product does not guarantee insulating. Keep an adequate insulating distance to surrounding parts.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
for Inrush Current Suppression Lead Type Package
35
6
Minimum Quantity
Part NumbersMinimum Quantity (pcs.)
BulkAmmo pack
NTPA7 1000 100
NTPAA 750 100
NTPAD 400 100
NTPAJ - 100
NTPAN - 100
NTPAD/NTPAA Series
Pitch of Component
Pitch of Sprocket Hole
Lead Spacing
Length from Hole Center to Lead
Length from Hole Center to Component
Body Diameter
Deviation along Tape, Left or Right
Carrier Tape Width
Position of Sprocket Hole
Lead Distance between Reference and Bottom Planes
Hight of Component
Overflow of Lead
Diameter of Sprocket Hole
Lead Diameter (Sn-Plated Cu Wire)
Total Tape Thickness
Total Thickness, Tape and Lead Wire
Deviation across Tape
Portion to cut in Case of Defect
Hole Down Tape Width
Hole Down Tape Position
Coating Extension on Lead
P
P0
F
P1
P2
D
∆S
W
W1
H0
H2
I
D0
d
t1
t2
∆h1, ∆h2
L
W0
W2
e
30.0
15.0±0.3
7.5±0.5
7.5±1.5
3.75±1.0
(refer to the table below)
Thickness T (refer to the table below)
±2.0
18.0±0.5
16.0±0.5
Max. 10.0
W0.5 to Y6.0
4.0±0.1
0.8±0.05
0.6±0.3
Max. 2.0
Max. 2.0
Min. 11.5
Max. 4.0
to line A
CodeItem Dimensions (mm)
9.0±0.5
11.0+0–2.0
NTPAD
NTPAA
Type D T
16.0 max. 5.5 max.
12.0 max. 5.0 max.
W0
W2
W
W1
H0
H2
∆h2∆h1
e
∆SP2 P
D
P1
P0
F d
l
øD0
L
t2 t1
T
A
Continued on the following page.
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
for Inrush Current Suppression Lead Type Package
36
6
Continued from the preceding page.
NTPA7 Series
Pitch of Component
Pitch of Sprocket Hole
Lead Spacing
Length from Hole Center to Lead
Length from Hole Center to Component
Body Diameter
Deviation along Tape, Left or Right
Carrier Tape Width
Position of Sprocket Hole
Lead Distance between Reference and Bottom Planes
Hight of Component
Overflow of Lead
Diameter of Sprocket Hole
Lead Diameter (Sn-Plated Cu Wire)
Total Tape Thickness
Total Thickness, Tape and Lead Wire
Deviation across Tape
Portion to cut in Case of Defect
Hole Down Tape Width
Hole Down Tape Position
Coating Extension on Lead
P
P0
F
P1
P2
D
∆S
W
W1
H0
H2
I
D0
d
t1
t2
∆h1, ∆h2
L
W0
W2
e
12.7
12.7±0.3
5.0
6.35±1.3
3.85±0.8
Max. 9.0
Thickness T Max. 5.0
±1.5
18.0±0.5
16.0±1.0
Max. 6.0
W0.5 to Y4.0
4.0±0.3
0.6±0.05
0.6±0.3
Max. 2.0
Max. 1.5
Min. 11.0
Max. 4.0
to line A
CodeItem Dimensions (mm)
9.0
11.0+0–2.0
+0.8–0.3
+0.5–0.75
W0
W2
W
W1
H0
H2
∆h2∆h1
e
∆SP2 P
D
A
P1
P0
F d
l
øD0
L
t2 t1
T
Head Office2-26-10, Tenjin Nagaokakyo-shi, Kyoto 617-8555, Japan Phone:81-75-951-9111
International Division3-29-12, Shibuya, Shibuya-ku, Tokyo 150-0002, Japan Phone:81-3-5469-6123 Fax:81-3-5469-6155 E-mail:[email protected]
http://www.murata.co.jp/products/
Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requestedto approve our product specification or to transact the approval sheet for product specification, before your ordering.
R44E6.pdf 02.2.22
Note:1. Export Control
<For customers outside Japan>Murata products should not be used or sold for use in the development, production, stockpiling or utilization of any conventional weapons or mass-destructiveweapons (nuclear weapons, chemical or biological weapons, or missiles), or any other weapons.<For customers in Japan>For products which are controlled items subject to the “Foreign Exchange and Foreign Trade Law” of Japan, the export license specified by the law is requiredfor export.
2. Please contact our sales representatives or product engineers before using our products listed in this catalog for the applications listed below which requireespecially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property, or when intending to use oneof our products for other applications than specified in this catalog.q Aircraft equipmentw Aerospace equipmente Undersea equipmentr Power plant equipmentt Medical equipmenty Transportation equipment (vehicles, trains, ships, etc.)u Traffic signal equipmenti Disaster prevention / crime prevention equipmento Data-processing equipment!0 Application of similar complexity and/or reliability requirements to the applications listed in the above
3. Product specifications in this catalog are as of November 2001. They are subject to change or our products in it may be discontinued without advance notice.Please check with our sales representatives or product engineers before your ordering. If there are any questions, please contact our sales representatives orproduct engineers.
4. Please read CAUTION and Notice in this catalog for safety. This catalog has only typical specifications. Therefore you are requested to approve our productspecification or to transact the approval sheet for product specification, before your ordering.
5. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effectof our and/or third party's intellectual property rights and other related rights in consideration of your using our products and/or information described orcontained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentionedabove under licenses without our consent.
6. None of ozone depleting substances (ODS) under the Montreal Protocol is used in manufacturing process of us.