nu horizons q2 2012 edition of portal
DESCRIPTION
Nu Horizons releases its Q2 2012 Edition of Portal - your gateway to today’s leading technology productsTRANSCRIPT
See page 23
IN THIS ISSUE:
Your Gateway
to Today’s Leading
Technology Products
DEVELOPMENT TOOLSRenesas
DATACOMMicrel
DISPLAYSOptrex / KyoceraTouch Revolution
EMBEDDED SYSTEMSiEi Technology
MEMORYMicronWinbond
MICROCONTROLLERSAtmel
POWER MANAGEMENTAllegro MicroSystemsLinear TechnologyMicrelWürth Midcom
POWER SUPPLIESMean WellN2Power
PROGRAMMABLE LOGICLattice
Q2 2012Americas Edition
Info & Free Samples
, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners.
In harsh industrial, automotive and military applications, systems must operate reliably through severe overvoltage events. The LTC®4366’s adjustable floating topology is capable of extremely high voltages; the operational upper voltage is limited only by MOSFET ratings. During high voltage transient events, the LTC4366 clamps the output to a user-defined voltage, while the fault timer ensures safe shutdown of the MOSFET if the fault persists.
www.linear.com/product/LTC4366
1-800-4-LINEAR
PartNumber
LT®
4356
LTC4360
LTC4361
LTC4362
LT4363
LTC4365
LTC4366
–60V
Yes
Yes
Yes
–60V
–40V
Yes
VIN Max
100V
80V
80V
28V
100V
60V
Unlimited
OperatingRange
ReverseProtection
4V to 80V
2.5V to 5.5V
2.5V to 5.5V
2.5V to 5.5V
4V to 80V
2.5V to 34V
9V to >500V
OvercurrentProtection
Yes, <100V
Yes
1.5A
Yes, >100V
PackageOptions
4mm x 3mm DFN,MSOP-10, SO-16
SC70-8
2mm x 2mm DFN, TSOT-8
2mm x 3mm DFN
4mm x 3mm DFN,MSOP-12, SO-16
3mm x 2mm DFN,TSOT-8
3mm x 2mm DFN,TSOT-8
Comments
Surge Stopper withAuxiliary Amplifier
Overvoltage Protection Controller
Overvoltage/OvercurrentProtection Controller
Overvoltage Protection Controller
High Voltage Surge Stopper withCurrent Limit
UV, OV & Reverse SupplyProtection Controller
Floating Surge Stopper
Overvoltage and Overcurrent Protection Family
Unlimited Overvoltage Protection
www.linear.com/ad/4366
LTC4366 Ad (Portal).indd 1 2/29/12 11:07 AM
Info & Free Samples
, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners.
In harsh industrial, automotive and military applications, systems must operate reliably through severe overvoltage events. The LTC®4366’s adjustable floating topology is capable of extremely high voltages; the operational upper voltage is limited only by MOSFET ratings. During high voltage transient events, the LTC4366 clamps the output to a user-defined voltage, while the fault timer ensures safe shutdown of the MOSFET if the fault persists.
www.linear.com/product/LTC4366
1-800-4-LINEAR
PartNumber
LT®
4356
LTC4360
LTC4361
LTC4362
LT4363
LTC4365
LTC4366
–60V
Yes
Yes
Yes
–60V
–40V
Yes
VIN Max
100V
80V
80V
28V
100V
60V
Unlimited
OperatingRange
ReverseProtection
4V to 80V
2.5V to 5.5V
2.5V to 5.5V
2.5V to 5.5V
4V to 80V
2.5V to 34V
9V to >500V
OvercurrentProtection
Yes, <100V
Yes
1.5A
Yes, >100V
PackageOptions
4mm x 3mm DFN,MSOP-10, SO-16
SC70-8
2mm x 2mm DFN, TSOT-8
2mm x 3mm DFN
4mm x 3mm DFN,MSOP-12, SO-16
3mm x 2mm DFN,TSOT-8
3mm x 2mm DFN,TSOT-8
Comments
Surge Stopper withAuxiliary Amplifier
Overvoltage Protection Controller
Overvoltage/OvercurrentProtection Controller
Overvoltage Protection Controller
High Voltage Surge Stopper withCurrent Limit
UV, OV & Reverse SupplyProtection Controller
Floating Surge Stopper
Overvoltage and Overcurrent Protection Family
Unlimited Overvoltage Protection
www.linear.com/ad/4366
LTC4366 Ad (Portal).indd 1 2/29/12 11:07 AM
PO
RTA
L C
ON
TE
NT
S
Nu Horizons Electronics is a leading
distributor of advanced technology
semiconductor, display, illumination
and power solutions to a wide variety
of commercial original equipment
manufacturers (OEMs) and electronic
manufacturing services providers
(EMS).
With sales facilities in 45 locations
across North America and Asia and
regional logistics centers throughout
the globe, Nu Horizons partners with
a limited number of best-�in-�class
suppliers to provide in-�depth product
development, custom logistics and
life-�cycle support to its customers.
Need more information right away?
Just use your smartphone to scan the barcodes throughout this publication and you'll link to more detailed information.
Note: You will need a QR Code Reader downloaded to your phone (i-�nigma is free).
All registered trademarks displayed in this publication constitute the intellectual property of their respective holders. The technical information within this publication has been provided by Nu Horizons' suppliers. Nu Horizons does not assume any liability for its accuracy. Prices are subject to change without notice.
APPLICATION NOTESSamsung LED Design Considerations for LED Lighting Applications 4
DEVELOPMENT TOOLSRenesas Motor Control Evaluation Kit with RX62T 5
FEATURED COMPONENTSDatacom Micrel — EtherSynch™ 6
Embedded SystemsiEi Technology — Introducing Intel Performance i3/i5/i7 and Low Power Dual Core Atom Solutions
9
Memory Micron — N25Q SPI NOR Flash Memory Family 10
Memory Micron — Product Longevity Program 11
Memory Winbond — Advanced Memory Solutions 12
MicrocontrollersAtmel — SAM3X/SAM3A Cortex-�M3 Processor-�based Flash Microcontrollers
13
Power & Battery ManagementAllegro MicroSystems — Full-�Bridge DMOS PWM Motor Drivers
14
Power & Battery ManagementAllegro MicroSystems — High Current Integrated Full-�Bridge PWM Motor Driver
15
Power & Battery ManagementAllegro MicroSystems — DMOS Microstepping Motor Drivers With Overcurrent Protection
16
Power ManagementLinear Technology — LTC5585 -� Wideband IQ Demodulator with IIP2 and DC Offset Control
17
Power ManagementLinear Technology — LTC3600 -� 15V, 1.5A Synchronous Rail-�to-�Rail Single Resistor Step-�Down Regulator
18
Power Management Micrel — IC Family Reduces Switching Regulator 19
Power ManagementWürth Midcom — SMD Power Inductor, Compact Design with High Saturation Current
20
Power Supplies N2Power — XL375 CC -� 260 Watts without Fans 22
Programmable Logic Lattice Semiconductor — iCE Family 24
Programmable Logic Lattice Semiconductor — MachXO2 Family 25
ADVERTISEMENTSLinear Technology Surge Stopper 2
Optrex / Kyocera Optrex Corporation is now Kyocera Display Corporation 7
Touch Revolution World Leader in Projected Capacitive Touch 8
Renesas The RL78 Green Energy Challenge 21
Mean Well Total Solutions for LED Power Supply 23
Nu Horizons Supplier Matrix LED Drivers Matrix highlighting LEDs / Channel 26
Nu Horizons Supplier Matrix LED Drivers Matrix highlighting Current / Channel 27
Samsung LED / Nu Horizons Innovative Lighting Solutions 28
Nu Horizons LED Lighting Line Card 29
Nu Horizons Display Technologies Line Card 30
Nu Horizons Embedded Solutions / Single Board Computers 31
Nu Horizons Semiconductor Technologies Line Card 32-�35
Nu HorizonsEnhance Your Design...With Nu Horizons Education and Development Solutions
36
Design Considerations for LED Lighting Applications
Introduction
Lighting applications have grown dramatically from those supporting
status indicators on front panels to a wide range of general and special
purpose illumination applications. LEDs, due to their high reliability, low
power, low heat output, precise and long lifetime lighting characteristics
are rapidly replacing older lighting technologies.
Designing lighting applications, using LEDs, is more involved than
fi nding the latest and greatest LED. LED lighting systems are comprised of
multiple subsystems: LEDs, LED drivers, thermal management, and optics-�
each interacting with the other to affect the system's overall performance.
This application note will use several different applications examples
to illustrate the various design considerations and trade-�offs that are
involved in modern LED-�based lighting designs. These applications have
been selected to illustrate a wide range of design considerations and
in many cases more design details are available in reference designs,
evaluation kits and other supporting documents. These documents and
web sites are listed in the Reference section of this application note to
make it easy to continue exploring topics of additional interest.
Example Applications
In order to cover a majority of the LED lighting design considerations
we will look at several different designs. Backlighting designs are
a key segment for LED lighting so we will look at an industrial display
backlighting design. Solid state lighting, like that found in information
display applications, is also a growing area where LED lighting is found
so that will be another of our examples. A handheld device design and a
computer controlled offi ce space lighting application will fi nish out our set
of example designs.
Nu Horizons LED Lighting Solutions
Nu Horizons has put together a full team of industry veterans from
each of the LED lighting disciplines. Individually, each company offers
leading-�edge products and services and outstanding customer support.
Working together, the team offers comprehensive, cross-�discipline design
tools and educational opportunities. In order to better explain these
capabilities, this application note also includes a summary of the various
products, capabilities and specializations of the Nu Horizons team. Use this
as a reference during product selection and as a roadmap to more detailed
data during the design phase.
The topics covered in this application note include the following:
1) Introduction
2) Key LED Lighting Design Considerations
a. LEDs
b. Nu Horizons LED Suppliers
c. LED Drivers
d. Nu Horizons Driver Suppliers
e. Thermal Management
f. Nu Horizons Thermal Management Suppliers
g. Optics
h. Nu Horizons Optics Suppliers
3) Example Applications
a. Description
b. Block Diagram
c. Design Considerations
d. Component Selection
4) Summary and References
To download the complete application note, please scan the barcode below
or visit the application notes section of the Nu Horizons website.
Scan barcode to access complete application note
4 Nu Horizons offers a wide range of application notes and white papers. For more information, please visit www.nuhorizons.com/application_notes
AP
PL
ICA
TIO
N N
OT
ES
LED Lighting Solutions
Nu Horizons offers a wide range of development / evaluation boards, tools and kits. For more information, please visit www.nuhorizons.com/development
Scan barcode for more information regardingthe RX62T Evaluation Kit
5
DE
VE
LO
PM
EN
T T
OO
LS
With the Renesas RX600 Motor ControlEvaluation Kit, you can: Learn the RX62T motor control feature set
Explore advanced motor control algorithms
Monitor speed and position regulation
Observe responsiveness to load changes
Connect with user-�supplied inverter
Debug using on-�board test points and the E1 emulator Evaluation Kit Contents: Control Board with RX62T MCU and RJK0656DPB Power MOSFETs
24V/4-�pole BLDC motor with encoder and hall sensor
E1 debugger for software debugging and Flash programming
CD ROM containing sample code, motor control library, HEW IDE and evaluation copy of Renesas RX compiler, schematics, user guide and application notes
Kit also offers: Sensorless vector control (1 or 3 shunt)
External or internal PGA selection (via jumpers)
Position control using encoder
Standalone mode using LCD and push-�button
Connector for user-�supplied inverter stage
Renesas Motor Control Evaluation Kit with RX62TReady-to-use Platform for Evaluating Sensorless Vector and Position Control
Use the Renesas RX600 Motor Control Evaluation Kit to develop your motor control solutions. With
its high-�performance CPU and FPU capability, and advanced analog and timer peripherals, the RX62T
is an ideal MCU for inverter and motor control applications. The RX62T firmware supports many kinds
of motor control, including high-�precision three-�phase sensorless vector control. The supplied GUI
provides precise tracking of speed, position, voltage and current.
The RX62T MCU is capable of driving two three-�phase motors simultaneously using its
advanced PWM timers. These timers are well suited for Brushless DC three-�phase motors by having
complimentary PWM outputs with automatic dead-�time insertion, an emergency “Shut-�down” (stop)
input, and quadrature encoder inputs for speed and direction feedback. The RX62T’s advanced analog
subsystem with multiple sample-�hold circuits enables sampling of three simultaneous current
measurements. It also offers programmable operational amplifiers and integrated
window comparators to eliminate external components. The 12-�bit ADCs
have a fast 1μsec conversion time, can be triggered by the PWM
timers, and provide self-�diagnostic capability.
Motor Current
Detection Circuit Comp
PGA12-bit ADC S/H
Fault Signal
PWM Output
Ana
log
Tim
er
PWM Interrupt
PWM Generation
3
6
Motor Current
Detection Circuit Comp
PGA12-bit ADC S/H
Fault Signal
PWM Output
Ana
log
Tim
er
PWM Interrupt
PWM Generation
3
6
RX62T
CAN
Analog
GPIO
Timers
User-friendly GUI forPerformance Evaluation: Speed, voltage and current tracking
Bi-�directional speed/position control
User selectable vector control algorithms
System status indicator
Data-�logging
Home appliance example
DA
TA
CO
M
6 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
Scan barcode for more KSZ84xx family information
Micrel EtherSynch™KSZ84xx IEEE1588v2 Ethernet Family -IEEE1588v2 made simple
The KSZ84xx controller and switch families enable end-�device attachments for industrial Ethernet and power substation automation networks. Key applications include industrial Ethernet standards, including EtherNet/IP™, PROFINET®, Modbus TCP™, and POWERLINK, along with IEC 61850 electrical power substation automation networks that employ distributed (ring or linear) topologies. They simplify integration with Host CPUs that do not provide embedded Ethernet MACs and has been optimized to off-�load synchronization and communications host processing through its hardwire-�intensive architecture.
Micrel offers a precision timing protocol (PTPv2) synchronization stack solution integrated with the KSZ84xx driver to accelerate the design cycle. The KSZ84xx products also interoperable with leading third-�party PTP stacks.
Micrel features the industry’s most robust and cost-�effective Ethernet switches and physical layer transceivers, built upon Micrel’s low-�power physical layer technology, advanced power management, and innovative design.
APPLICATIONS:
Industrial control Power substation automation Telecommunications Data acquisition Aerospace Seismic Subsea Rail Medical
BENEFITS:
Supports broad range of topologies
Reduces Host CPU processing load and network traffi c
Extends system synchronization to locally-�connected devices
Enables distributed, daisy-�chained topologies
Supports a wide range of Host CPUs
Reduces time to deployment with pre-�qualifi ed solution
Less board resources required reduces BOM costs
Industry’s lowest power consumption and energy effi ciency
FEATURES:
Comprehensive PTP clock modes
Hardware-�assisted PTP implementation
Extensive GPIO synchronized to precision clock
Bypass mode and source address fi ltering
Flexible Host Interface Options: MII, RMII, and Generic Host Interface
PTP protocol stack integrated with KSZ84xx driver
Compact 10mm x 10mm, 64-�pin, LQFP package
Advanced power management
Part Number Description
KSZ8463MLI 3-�Port 10/100Mbps Ethernet Switch with MII
KSZ8463RLI 3-�Port 10/100Mbps Ethernet Switch with RMII
KSZ8462HLI 2-�Port 10/100Mbps Ethernet Switch with Host interface
KSZ8441HLI Single-�Port 10/100Mbps Ethernet MAC/PHY Controller with Host interface
9
EM
BE
DD
ED
SY
ST
EM
S
BENEFITS:
Custom engineering Best-�in-�class design Global service
ODM / OEM service Quality assurance
FEATURES:
Hardware: Wide temperature (-�30°C ~70°C ) Water resistant Flexible expansion Compact ruggedize design Wide voltage system Redundant power input Module design USB 3.0
Software: Complete embedded OS support Intel AMT 7.0/8.0 support Auto recovery Intelligent system management module Smart fan
IEI I3/I5/I7 AND LOW POWER DUAL CORE ATOM PRODUCT APPLICATIONS:
For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
Scan barcode for more information oniEi high-�performance solutions
Introducing Intel Performance i3/i5/i7 and Low Power Dual Core Atom SolutionsThe #1 Industrial PC Manufacturer leads the embedded market into high-performance level
IEI Technology USA Corp. is a leading industrial computing service provider integrating
computing platforms and customization services. IEI supplies hundreds of Intel based
industrial computer boards, systems and peripherals in thousands of customer applications,
and supports OEM/ODM services to reduce customers’ engineering effort and accelerate
the product development process to help customers get ahead of the market competition.
IEI has an innovative R&D team, intelligent management system, high quality assurance and
over 400 products passing through more than 100 distributors providing customers with the
fastest time-�to-�market services all over the world.
IEI Technology USA Corp.
Board Level
Servers Model Name
PCIE-�H610 IMB-�H612
WSB-�H610 KINO-�DH610
IMBA-�H610 KINO-�AH611
IMB-�H610 KINO-�AH612 IMBA-H610
Embedded Systems
Automation Model Name
TANK-�101B TANK-�820-�H61
TANK-�700-�QM67 Wstrider-�200A
TANK-�720-�Q67 ECM-�680
TANK-�800-�D525 uIBX-�200 TANK-820
Medical
Bedside Infotainment Model Name
IBS-�19A POC-�3/A Series
POC-�5/A Series POC-�3/B Series
POC-�4/A Series MMC-�2201C
POC-�4/B Series MMD-�4300C IBS-19A
Digital Signage
Outdoor Display Model Name
IOPS-�Q67 iS-�1500
IOPS-�H61 iS-�510H
iS-�810WL iS-�500A
iS-�800WL Video Wall Series IOPS Series
Mobile
Vehicle Information Model Name
ICEFIRE-�T10A MODAT-�328
ICEROCK-�08A iKARPC-�W08A
MODAT-�100 VTT-�1000
MODAT-�200 AVL-�2000 ICEFIRE-T10A
Industrial Panel PCs
Infotainment Model Name
AFL2-�15A-�H61
AFL2-�W15B-�H61
AFL2-�17A-�H61
AFL2W18A-�H61 AFL2-15A-H61
ME
MO
RY
10
N25Q SPI NOR Flash Memory FamilyMicron’s N25Q Serial Peripheral Interface (SPI) NOR Flash family is socket and software compatible from 32Mb to 1Gb
MicronN25Q SPI NOR product line was expanded last year to include 1 gigabit (Gb), 512 megabit (Mb) and 256Mb density products in both 1.8V and 3V power supply voltages. Employing state-�of-�the-�art 65nm process technology, the N25Q product family offers the highest-�speed quad I/O in the industry and a full set of advanced features and small packages that improve overall system performance and time-�to-�market in a wide range of industrial and automotive applications.
The N25Q family provides package and software compatibility across densities, from 32Mb to 1Gb. When you combine industrial temperature range, 1.8V and 3.0V power supply options, and the longevity of Micron's PLP program, this product family provides an ideal solution for the your embedded SPI NOR needs.
Scan barcode for more N25Q SPI NOR Flash Memory Family information
For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
FEATURES:
Micron's best-�in-�class N25Q SPI NOR family offers the following advanced features:
Multiple I/O protocol — single SPI, dual SPI (DSPI) and quad SPI (QSPI)
Double transfer rate (DTR) feature enhances read performance
54MB/s read transfer rate at 108 MHz clock
Footprint compatibility across the entire line, from 32Mb up to 1Gb
500KB/s program speed
4 bytes of address mode supported for high-�density range requirements (128Mb+)
Execute-�in-�place (XIP) capability supports code execution directly from the fl ash, reducing RAM usage and overall cost
Nonvolatile confi guration register delivers maximum fl exibility in application usage models
APPLICATIONS:
Medical Smart Meters Embedded PC Defense Factory Automation Automotive
The N25Q SPI NOR family is in production now, check out the product catalog to see which device fi ts your design.
http://www.micron.com/products/nor-�fl ash/serial-�nor-�fl ash/multi-�nor-�n25q
Micron Product Longevity ProgramMicron’s PLP is designed to provide stable memory architectures for long-life applications like those in automotive, industrial, medical, and aerospace. Through PLP we make a range of DRAM, NAND, and NOR devices available for a minimum of 10 years.
Applications with extended life cycles face a challenge as the components designed appear to
go through constant change; whether from obsolescence, process shrinks, new features and even
industry consolidation. This adds up as you spend time, resources and dollars long after the product
has entered production.
Recognizing this need for product longevity Micron introduced the Product Longevity Program
for select DRAM, NAND and NOR memory devices available for a minimum of 10 years.
The 10-�year lifecycles for Micron PLP products will begin when a product is introduced into the
PLP and will include extended notifi cation and conversion timelines.
Given the longevity of devices in the PLP program, it may be necessary to transition the device
to a new silicon process node or move production to an alternate manufacturing facility. In these
cases, Micron will re-�qualify the device and inform PLP customers of any corresponding ordering
part-�number changes.
To facilitate these transitions, PLP-�eligible products have extended notifi cation and conversion
timelines; participating customers will be given 12 months from notifi cation to place last-�time orders
and an additional 12 months to receive last-�time shipments. This notifi cation period is double the
standard notifi cation period, allowing customers two years to convert to newer products.
The line-�card below summarizes the part families in the program..
ME
MO
RY
11For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
Product Fami ly* Densi ty Range* Temp Range*
DR
AM
DDR3 (MT41) 1-�2Gb IT, AT
DDR2 (MT47) 1-�2Gb IT, AT
DDR (MT46) 256-�512Mb IT, AT
SDRAM (MT48) 128-�256Mb IT, AT
Par
alle
l N
OR
Parallel NOR (M29EW) 64Mb-�1Gb IT
Parallel NOR (M29W) 8-�256Mb IT, AT
Parallel NOR (M588W) 16Mb AT
Parallel NOR (P30) 64Mb-�1Gb IT
Parallel NOR (P33) 64Mb-�1Gb IT
Parallel NOR (J3) 64-�256Mb IT
SPI N
OR Serial NOR (N25Q) 32-�256Mb IT, AT
Serial NOR (M25PEIM45PE) 4-�16Mb IT, AT
Serial NOR (M25P) 4-�16Mb IT, AT
NA
ND
SLC, VLP NAND Flash (MT29) 8Gb IT
SLC, LP NAND Flash (MT29) 1-�4Gb IT
SLC, SPI NAND Flash (MT29) 1-�4Gb IT
SLC, SP NAND Flash (NAND) 128-�512Mb IT
* The partial part numbers referenced above are product family designators only. Not all products or part numbers are in the PLP. Refer to the PLP Part List to verify specifi c part numbers that are included in the program.
Go to www.micron.com/plp to download the complete part number list and see which parts fi t your design
AUTOMOTIVE
MEDICAL
INDUSTRIAL
AEROSPACE
DEFENSE
Scan barcode for more PLP information
ME
MO
RY
12 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
Scan barcode for more Winbond memory solutions
Advanced Memory Solutions
SPIFLASH® SERIAL FLASH MEMORIES:
Winbond's W25X and W25Q SpiFlash® memories feature the popular Serial Peripheral Interface (SPI), densities from 1M to 256M-�bit, small erasable sectors and the industry's highest performance. The W25Q family operates up to 104MHz and supports "Quad-�SPI", increasing effective clock rate to 416MHz. SpiFlash® memories offer a pin, space and cost effi cient alternative to ordinary Parallel Flash memories, and are ideal for a wide range of applications including: PCs, DVD, Blu-�Ray, WLAN, DSL & Cable modems, Printers, Hard Drives, Set Top Box, LCD-�TV, Mobile Phones, Bluetooth, GPS, MP3, Meters, DSP, FPGAs, Automotive and more.
PARALLEL FLASH MEMORIES:
Winbond's W29GL family of Page Mode Parallel Flash memories are offered in densities from 32Mb to 256Mb and support industry standard interfaces and architectures. They are drop-�in replaceable to the x29GL products available in the industry with no fi rmware change. They also offer faster program and erase times which improves customer throughput and offers faster fi rmware updates. Our Parallel Flash products are ideal for a wide variety of applications including: Networking, set-�top-�box, DSL and cable modems, servers, industrial, wireless routers, PC peripherals, printers, mobile phones, digital cameras and more.
SPECIALTY DRAM:
Winbond’s DRAM product portfolio consists of high performance Mobile RAM, Specialty DRAM and Graphics DRAM. These products are widely used by leaders in the consumer, communication, computer peripheral and automobile markets. Specialty DRAM products are used in all applications excluding main PC memory. All products are offered in JEDEC standard packages.
DensitySecure Sectors
Speed (ns) Page Access (ns) PackageBoot/Uniform Sectors Sector Location
32M-�bitTop/Bottom Boot Top/Bottom two sectors 70 25 TSOP48, TFBGA48, LFBGA64
Uniform Sector High/Low Sector 70 25 TSOP56, LFBGA64
64M-�bitTop/Bottom Boot Top/Bottom two sectors 70 25 TSOP48, TFBGA48, LFBGA64
Uniform Sector High/Low Sector 70 25 TSOP56, LFBGA64
128M-�bit Uniform Sector High/Low Sector 90 25 TSOP56, LFBGA64
256M-�bit Uniform Sector High/Low Sector 90 25 TSOP56, LFBGA64
Type Org Densities Speed Package Temp Range
Mobile DRAM
mSDR x16, x32 128Mbit, 256Mbit, 512Mbit 133MHz, 166 MHz VFBGA 54, VFBGA90 C, I
mDDR x16, x32 128Mbit, 256Mbit, 512Mbit 166MHz, 200MHz VFBGA 60, VFBGA90 C, I
Specialty DRAM
SDRAM
x16 16M 166MHz TSOPII 50, VFBGA 60 C, I
x16, x32 64M 166MHz TSOPII 54, VFBGA 60, TSOPII 86, TFBGA90 C, I
x16, x32 128M 166MHz TSOPII 54, TFBGA 54, TSOPII 86, TFBGA90 C, I
x16, x32 256M 166MHz TSOPII 54, TFBGA 54, TFBGA90 C, I
DDR x16 64M, 128M, 256M 200MHz TSOPII 66 C, I
DDR2x8, x16 128M, 256M, 512M, 1G 800Mbps, 1066Mbps WBGA 60, WBGA 84 C, I
x8, x16 2G 667Mbps WBGA 60, WBGA 84 C, I
DDR3 x16 1G 1333Mbps, 1600Mbps WBGA 96 C
Density Speed MHz Voltage Package Temp AEC-Q100 Automotive
512K-�bit 50/104 2.5V SO8, TSSOP8, WSON8, USON8 I
1M-�bit 50/104 2.5V, 3V SO8, TSSOP8, VSOP8, WSON8, USON8 I
2M-�bit 50/80/104 2.5V, 3V SO8, VSOP8, WSON8, USON8 I, A √
4M-�bit 50/80/104 1.8V, 2.5V, 3V SO8, VSOP8, WSON8, PDIP8, USON8 I, A √
8M-�bit 50/80/104 1.8V, 2.5V, 3V SO8, VSOP8, WSON8, PDIP8, USON8, WLBGA8 I, A √
16M-�bit 50/80/104 1.8V, 2.5V, 3V SO8, VSOP8, SO16, WSON8, PDIP8, TFBGA24, WLBGA8 I, A √
32M-�bit 80/104 1.8V, 3V SO8, VSOP8, SO16, WSON8, PDIP8, TFBGA24 I, A √
64M-�bit 80/104 1.8V, 3V SO8, VSOP8, SO16, WSON8, PDIP8, TFBGA24 I, A √
128M-�bit 70/104 1.8V, 3V S08, VSOP8, SO16, WSON8, PDIP8, TFBGA24 I, A √
256M-�bit 104 3V SO16, WSON8, TFBGA24 I, A √
Device
Max. OperatingFrequency
(MHz)
Memory Serial Interfaces Analog Parameters
QTouchChannels
Pin Count PackageFlash (KB)
SRAM (KB)
External Bus
InterfaceUSB Ethernet
DualCAN
UART/SPI/TWI
HSMCII/F
ADC DAC
SAM3N 48 16 -� 256 4 -� 24 -� -� -� -� 4 / 3 / 2 -� 10-�bit 10-�ch 10-�bit 1-�ch 17, 23 48, 64, 100LQFP,
QFN, BGA
SAM3S 64 32-� 512 16 -� 64 1 FS Device -� -� 4 / 3 / 2 1 12-�bit 16-�ch 12-�bit 2-�ch 17, 23, 32 48, 64, 100LQFP,
QFN, BGA
SAM4S16 120 1024 128 1 FS Device -� -� 4 / 3 / 2 1 12-�bit 16-�ch 12-�bit 2-�ch 32 100 LQFP
SAM3U 96 64 -� 256 20 -� 52 1 HS Device -� -� 4 / 5 / 2 18-�ch 12-�bit,
10-�bit-� 28, 32 100, 144 LQFP, BGA
SAM3A 84 256 -� 512 64 -� 96 -�HS Host & Device w/
PHY-� Yes 4 / 4 / 2 1 12-�bit 16-�ch 12-�bit 2-�ch 31 100, 144 LQFP, BGA
SAM3X 84 256 -� 512 64 -� 100 1HS Host & Device w/
PHYYes Yes 5 / 4 / 2 1 12-�bit 16-�ch 12-�bit 2-�ch 31, 32 100, 144 LQFP, BGA
Atmel SAM3X/SAM3A Cortex-M3 Processor-based Flash Microcontrollers
The Atmel® SAM3X/SAM3A series are the newest additions to one of the industry’s broadest ARM® Cortex™-�M series processor-�based Flash microcontroller portfolios. These devices bring more connectivity to the SAM3 family by adding Ethernet, dual CAN and high-�speed USB (HS USB) MiniHost and device with on-�chip physical layer (PHY). Devices feature a dual-�bank confi guration of 256KB and 512KB Flash total and are available in 100-�pin and 144-�pin QFP and BGA package options. The architecture is designed to support high-�speed data transfers and includes a multi-�layer bus matrix plus dual SRAM banks, direct memory access (DMA) channels and peripheral DMA controller (PDC) for applications supporting multi-�task operations. These high-�performance, highly integrated, low-�power devices are supported by development tools and a comprehensive ecosystem to accelerate your design cycle.
KEY FEATURES AND BENEFITS:
Optimized for Connectivity With its architecture and peripherals including Ethernet, dual CAN and HS USB MiniHost and device with on-�chip PHY, the SAM3X/SAM3A series are optimized for applications requiring high levels of connectivity.
Atmel QTouch Capacitive Touch Support The SAM3X/SAM3A series are touch-�ready, offering native support for Atmel QTouch® technology for easy implementation of buttons, sliders and wheels functionality in your applications.
Enhanced Safety and Security A variety of features integrated into the SAM3X/SAM3A series provides safety and security for your system. For example, dual-�bank Flash enables safe in-�system fi rmware upgrades. On-�the-�fl y external memory scrambling on the 16-�bit external bus interface enhances the protection of your external memory content, without impacting system performance. In addition, the SAM3X/ SAM3A series offer clock failure detection and a true random number generator.
Low Power Consumption All SAM3 MCUs feature a sophisticated, fl exible power management scheme that minimizes power consumption under all usage conditions. You can put the devices in back-�up mode with the core and peripherals powered down, reducing power down to 2.5uA for the SAM3X/SAM3A series. A high-�speed on-�chip RC oscillator accelerates wake-�up from back-�up mode, further reducing average power consumption.
APPLICATIONS:
Building and home control/automation
Industrial automation
Machine-�to-�machine (M2M)
Test and measurement
Medical
Smart grid
PC, cell phone gaming peripherals
ATMEL SAM3/SAM4 SELECTOR GUIDE
13
MIC
RO
CO
NT
RO
LL
ER
S
For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
Scan barcode for more information regarding Atmel's SAM3X/SAM3A microcontrollers
POW
ER &
BAT
TERY
MAN
AGEM
ENT
14
Scan barcode for more information regarding Allegro's A4952/53 PWM Motor Drivers
For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
Full-Bridge DMOS PWM Motor DriversWith Internal Fixed Off-time PWM Current Control and Over Current Protection
Designed for pulse width modulated (PWM)
control of DC motors, the A4952 and A4953 are
capable of peak output currents to ±2 A and
operating voltages to 40 V.
Input terminals are provided for use in
controlling the speed and direction of a DC
motor with externally applied PWM control
signals. Internal synchronous rectifi cation control
circuitry is provided to lower power dissipation
during PWM operation.
Circuit protection features include over
current protection, shorted load, motor lead
short to ground, motor lead short to supply,
thermal shutdown with hysteresis, under voltage
monitoring of VBB, and internal cross-�conduction
prevention.
The A4952 is provided in a low-�profi le 10-�pin MSOP package (suffi x LY) and the A4953 is provided in a low-�profi le 8-�pin SOICN package. Both packages
have an exposed thermal pad, and are lead (Pb) free, with 100% matte tin leadframe plating.
FEATURES:
Integrated DMOS full-�bridge rated for peak output currents to +/-�2 A and operating voltages to 40 V
Integrated charge pump, no external capacitors.
Single supply
Over current protection (OCP) from short-�circuit events such as motor lead short, shorted load, or short to supply
Selectable over current retry feature (A4952 only)
Internal PWM generator with adjustable current limit
Fault output (A4952 only)
The A4952 is provided in a low-�profi le 10-�pin MSOP package (suffi x LY)
BENEFITS:
Single chip solution for driving brush DC motor
If a short is detected, the open drain FLTn output signal goes low
Fault tolerant and reduced susceptibility to catastrophic damage
Allows an option to restart IC after a 2ms timeout if an OCP fault is detected
User can adjust peak current limit by choosing sense resistor value
Eliminates the need for external charge pump capacitors, and logic supply capacitor reducing pin count and minimizing external component count and cost
APPLICATIONS:
Primarily targeted at the Offi ce Automation market, however, it can be used for any commercial or industrial application
Printers, scanners, copiers
Fluid pumps
Solar applications
Contact your local Nu Horizons sales representative for samples / development tools.
POW
ER & B
ATTERY MAN
AGEM
ENT
15For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
Scan barcode for more information regarding Allegro's A4950 PWM Motor Driver
High Current Integrated Full-Bridge PWM Motor DriverWith Internal Fixed Off-time PWM Current Control and Over Current Protection
Designed for pulse width modulated (PWM)
control of DC motor, the A4950 is capable of peak
output currents to ±3.5 A and operating voltages
to 40 V.
Input terminals are provided for use in
controlling the speed and direction of a DC
motor with externally applied PWM control
signals. Internal synchronous rectifi cation control
circuitry is provided to lower power dissipation
during PWM operation.
Circuit protection features include over
current protection, shorted load, motor lead
short to ground, motor lead short to supply,
thermal shutdown with hysteresis, under voltage
monitoring of VBB, and internal cross-�conduction
prevention.
The A4950 is provided in a low-�profi le 8-�pin SOICN package (suffi x LJ) with exposed thermal pad. It is lead (Pb) free, with 100% matte tin leadframe
plating.
FEATURES:
Integrated DMOS full-�bridge rated for peak output currents to +/-�3.5A and operating voltages to 40V
Integrated charge pump, no external capacitors
Single supply, no logic supply needed
Over current protection (OCP) from short-�circuit events such as motor lead short, shorted load, or short to supply
Internal PWM generator with adjustable current limit
8L thermally enhanced SOIC (suffi x LJ)
BENEFITS:
Single chip solution for driving brush DC motor
Fault tolerant and reduced susceptibility to catastrophic damage
High current capability in small footprint
User adjustable peak current limit with reference voltage and external sense resistor
Eliminates the need for external charge pump capacitors, and logic supply capacitor reducing pin count and minimizing external component count and cost
APPLICATIONS:
Primarily targeted at the Offi ce Automation market, however, it can be used for any commercial or industrial application
Printers, scanners, copiers
Fluid pumps
Solar applications
Contact your local Nu Horizons sales representative for samples / development tools.
POW
ER &
BAT
TERY
MAN
AGEM
ENT
16
Scan barcode for more information regarding Allegro's Microstepping Motor Driver solutions
For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
DMOS Microstepping Motor Drivers With Overcurrent ProtectionSmall Footprint in Thermally Effi cient Packages
Allegro’s A4982, A4984, A4985 and A4988 devices are complete microstepping motor drivers with a built-�in translator for easy operation and overcurrent protection to reduce the rework cost in both manufacturing and normal operations. These devices require fewer external components and utilize a simple STEP and Direction interface. They are targeted at the offi ce automation market.
The A498x family is designed to operate bipolar stepper motors in full-�, half-�, quarter-�, eighth and sixteenth step modes, with an output drive capacity of up to 35V and ±2A. They include a fi xed off-�time current regulator which has the ability to operate in slow or mixed decay modes. The translator is the key to the easy implementation of the devices. Simply inputting one pulse on the STEP input drives the motor one microstep. There are no phase sequence tables, high frequency control lines, or complex interfaces to program. The interface is an ideal fi t for applications where a complex microprocessor is unavailable or is overburdened.
Internal synchronous rectifi cation control circuitry is provided to improve power dissipation during PWM operation. Internal circuit protection includes: overcurrent protection, thermal shutdown with hysteresis, undervoltage lockout (UVLO), cross-�conduction prevention. Special power-�on sequencing is not required.
Allegro’s A4982, A4984, A4985 and A4988 are offered in several different package options: a 28 and 32 contact 5 mm × 5 mm × 0.90 mm QFN (ET) package, a 24 contact 4.0 mm × 4.0 mm × 0.75 mm QFN (ES) package, and a 24 lead 7.8 mm × 4.4 mm × 1.2 mm eTSSOP (LP) package. All packages have exposed thermal pads for enhanced thermal dissipation, and are lead (PB) free with 100% matte tin plated lead frames.
FEATURES:
Step and direction interface
2 A peak output current
Overcurrent protection (OCP) for shorts between motor leads and motor leads to ground
Low RDS(on) DMOS outputs
Slow and mixed decay modes
Synchronous rectifi cation
Less than 10 uA sleep mode current
BENEFITS:
Two control lines versus 8 to 10 or more control lines for competing parallel interface devices; additional I/O lines can add to system cost; and commutation tables are not required
The 2 A rating is 0.5 A above most competitors; additional safety margin for high reliability designs.
OCP protection reduces the rework cost in manufacturing and in normal operation (shorted connectors, shorted motor windings, solder bridges on PC boards)
Mixed decay results in improved microstepping accuracy and reduced audible noise, an Allegro patented feature
Internal synchronus rectifi cation eliminates the need for expensive Schottky diodes.
Meets requirement for low current draw when disabled for ENERGY STAR® qualifi cation
APPLICATIONS:
Targeted for the Offi ce Automation and Industrial markets:
Printers
Scanners
Copiers
Contact your local Nu Horizons sales representative for samples / development tools.
17
PO
WE
R M
AN
AG
EM
EN
T
For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
LTC5585 - Wideband IQ Demodulator with IIP2 and DC Offset Control The LTC®5585 is a direct conversion quadrature demodulator optimized for high linearity receiver applications in the 700MHz to 3GHz frequency range. It is also usable in the 400MHz to 700MHz and 3GHz to 4GHz ranges with reduced performance. It is suitable for communications receivers where an RF signal is directly converted into I and Q baseband signals with bandwidth of 530MHz or higher. The LTC5585 incorporates balanced I and Q mixers, LO buffer amplifi ers and a precision, high frequency quadrature phase shifter. The integrated on-�chip broadband transformer provides a single-�ended interface at the RF input with simple off-�chip L-�C matching. In addition, the LTC5585 provides four analog control voltage interface pins for IIP2 and DC offset correction, greatly simplifying system calibration.
The high linearity of the LTC5585 provides excellent spurfree dynamic range for the receiver. This direct conversion demodulator can eliminate the need for intermediate frequency (IF) signal processing, as well as the corresponding requirements for image fi ltering and IF fi ltering. These I/Q outputs can interface directly to channel-�select fi lters (LPFs) or to baseband amplifi ers.
FEATURES:
700MHz to 3GHz Operating Frequency
High IIP3: 28.7dBm at 700MHz, 25.7dBm at 1.95GHz
High IIP2: 70dBm at 700MHz, 60dBm at 1.95GHz
User Adjustable IIP2 Up to 80dBm
User Adjustable DC Offset Null
High Input P1dB: 16dBm at 1950MHz
I/Q Bandwidth of 530MHz or Higher
Image Rejection: 43dB at 1950MHz
Noise Figure: 13.5dB at 700MHz 12.7dB at 1.95GHz
Conversion Gain: 2.0dB at 700MHz 2.4dB at 1.95GHz
Single-�Ended RF with On-�Chip Transformer
Shutdown Mode
Operating Temperature Range (TC): –40°C to 105°C
24-�Lead 4mm × 4mm QFN Package
APPLICATIONS:
LTE/W-�CDMA/TD-�SCDMA Base Station Receivers
Wideband DPD Receivers
Point-�To-�Point Broadband Radios
High Linearity Direct Conversion I/Q Receivers
Image Rejection Receivers
Scan barcode for more LTC5585 information
Direct Conversion Receiver with IIP2 and DC Offset Calibration
A/D
D/A
D/A
VGA
VGA
5585 TA01a
LPFRF
BPFLNABPF RFINPUT
LO
EN
LO INPUT
ENABLE
LPF
IP2 ADJUST
DC OFFSET
I+
I–
Q+
Q–
0°
90°
IP2 AND DCOFFSET CAL
LTC5585
VCC
5V
IP2 ADJUST
DC OFFSETIP2 AND DCOFFSET CAL
D/A
D/A
A/D
IIP2 vs IP2I, IP2Q Trim Voltage
IP2I, IP2Q (V)0
IIP2
(dBm
)
80
90
100
0.8 0.9
70
60
400.2 0.4 0.60.1 1.00.3 0.5 0.7
50
120fRF = 700MHz
110
I, –40°CI, 25°CI, 85°CI, 105°C
Q, –40°CQ, 25°CQ, 85°CQ, 105°C
Direct Conversion Receiver with IIP2 and DC Offset Calibration
A/D
D/A
D/A
VGA
VGA
5585 TA01a
LPFRF
BPFLNABPF RFINPUT
LO
EN
LO INPUT
ENABLE
LPF
IP2 ADJUST
DC OFFSET
I+
I–
Q+
Q–
0°
90°
IP2 AND DCOFFSET CAL
LTC5585
VCC
5V
IP2 ADJUST
DC OFFSETIP2 AND DCOFFSET CAL
D/A
D/A
A/D
IIP2 vs IP2I, IP2Q Trim Voltage
IP2I, IP2Q (V)0
IIP2
(dBm
)
80
90
100
0.8 0.9
70
60
400.2 0.4 0.60.1 1.00.3 0.5 0.7
50
120fRF = 700MHz
110
I, –40°CI, 25°CI, 85°CI, 105°C
Q, –40°CQ, 25°CQ, 85°CQ, 105°C
LTC3600 - 15V, 1.5A Synchronous Rail-to-Rail Single Resistor Step-Down Regulator The LTC3600 is a high effi ciency, monolithic synchronous buck regulator whose
output is programmed with just one external resistor. The accurate internally generated
50μA current source on the ISET pin allows the use of a single external resistor to
program an output voltage that ranges from 0V to 0.5V below VIN. The VOUT voltage feeds
directly back to the error amplifi er in unity gain fashion and equals the ISET voltage.
The operating supply voltage range is 4V to 15V, making it suitable for dual lithium-�ion
battery and 5V or 12V input point-�of-�load power supply applications.
The operating frequency is synchronizable to an external clock or programmable
from 200kHz to 4MHz with an external resistor. High switching frequency allows the use
of small surface mount inductors. The unique constant on-�time architecture is ideal for
operating at high frequency in high step-�down ratio applications that also demand fast
load transient response.
FEATURES:
Single Resistor Programmable VOUT
±1% ISET Accuracy
Tight VOUT Regulation Independent of VOUT Voltage
Easy to Parallel for Higher Current and Heat Spreading
Wide VOUT Range 0V to VIN – 0.5V
High Effi ciency: Up to 96%
1.5A Output Current
Adjustable Frequency: 200kHz to 4MHz
4V to 15V VIN Range
Current Mode Operation for Excellent Line and Load Transient Response
<1μA Supply Current in Shutdown
Available in Thermally Enhanced 12-�Pin (3mm × 3mm) DFN and MSOP Packages
APPLICATIONS:
Voltage Tracking Supplies
Point-�of-�Load Power Supplies
Portable Instruments
Distributed Power Systems
PO
WE
R M
AN
AG
EM
EN
T
18
Scan barcode for moreLTC3600 information
For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
Efficiency and Power Loss vs Output Current
LOAD CURRENT (A)
EFFI
CIEN
CY (%
)
POWER LOSS (W
)
0.001 0.1 1 100.01
VIN = 12VVOUT = 2.5V
CCM
CCM
DCM
40
50
60
70
80
30
20
10
0
90
100
0.4
0.5
0.6
0.7
0.8
0.3
0.2
0.1
0
0.9
1.0
DCM
POWERLOSS
High Efficiency, 1MHz, 1.5A Step-Down Converter
3600 TA01a
50µA
10µF
1µF
0.1µF
22µF
2.2µH
VIN12V
VOUT
VOUT2.5V
VIN
INTVCCISET DOOGPHTIDNG BFGPTR
RUN
BOOST
SW
LTC3600
MODE/SYNC
0.1µF 49.9k
PWM CONTROLAND SWITCH
DRIVER
8
5
7
9
1 6 10 3 4 2 12
11
13
–
+ERRORAMP
PO
WE
R M
AN
AG
EM
EN
T
For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal 19
Scan barcode for more MIC94300 / MIC94310 information
IC Family Reduces Switching Regulator New Innovative Solution Enabling Unmatched PSRR Performance for Noise Sensitive Systems
The MIC94310 Ripple Blocker™ is a monolithic integrated circuit that provides low-�frequency ripple attenuation (switching noise rejection) to a regulated output voltage. This is vital for applications where a DC/DC switching converter is required to lower or raise a battery voltage but where switching noise cannot be tolerated by sensitive downstream circuits such as in RF applications. The MIC94310 maintains high power supply ripple rejection (PSRR) with input voltages operating near the output voltage level to improve overall system effi ciency. A low-�voltage logic enable pin facilitates ON/OFF control at typical GPIO voltage levels.
The MIC94300 is an integrated load switch that incorporates Micrel's Ripple Blocker™ active fi lter technology. The MIC94300 provides high-�frequency ripple attenuation (switching noise rejection) for applications where a switching noise cannot be tolerated by sensitive downstream circuits such as in RF applications. A low-�voltage logic enable pin disconnects the pass element and places the MIC94300 into a low current-�shutdown state when disabled.
APPLICATIONS:
Smart phones
Table PCs and notebooks; webcams
Digital still and video cameras
Current-�limit and thermal-�limit protected
Global positioning systems
Mobile computing
Automotive and industrial applications
Video conferencing
Bar code scanners
FEATURES AND BENEFITS:
1.8V to 3.6V input voltage range
Active noise rejection over a wide frequency band >60dB from 40kHz to 5MHz (MIC94300) and >50dB from 10Hz to 10MHz at 200mA load (MIC94310)
Rated to 200mA output current
Current-�limit and thermal-�limit protected
Ultra-�small 0.88mm x 0.88mm 4-�ball CSP
1.2mm x 1.6mm, 4-�pin Thin MLF®
Logic-�controlled enable pin
−40°C to +125°C junction temperature range
Fixed output voltages (MIC94310)
For an introduction video to Ripple Blocker™ technology, go to http://www.micrel.com/rippleblocker/fl owplayer/play/ or
click on the black QR code with your smart phone.
SMD storage inductor with high saturation current and compact design:
The new high-�performance, space-�saving SMD storage choke series WE-�LMHI is
distinguished by high nominal and saturation currents. A special iron powder mixture
prevents the saturation of the core across the entire operating range. It also provides
magnetic shielding, which reduces the stray magnetic fi eld to a minimum and even
eliminates acoustic noise.
Würth Elektronik provides the new series in fi ve sizes (4020, 7030, 7050, 1040
and 1335) and thus covers a wide range of inductance values from 0.1 μH up to 22
μH. As a result of the molded design, nominal currents of up to 25 A and saturation
currents of up to 70 A are possible. A wide temperature range from –40°C to +125°C
is specifi ed.
Scan barcode for more SMD Power Inductor information
FEATURES:
Compact design
Minimum Size 4020: 4mm x 4mm x 1.8mm
Maximum Size 1335: 12.6mm x 12.6mm x 3.3mm
Magnetically shielded
High current capability
Handles high transient current spikes
No acoustic noise and no leakage fi eld
Frequency range up to 5Mhz
Lowest DCR/μH in this package size
Operating temperature: -�40C to +125C
APPLICATIONS:
DC/DC converters for high current power supplies
DC/DC converters for Field Programmable Gate Array (FPGA)
POL converters
Portable power like PDA, digital camera
Mainboards / graphic cards
Battery powered devices
BENEFITS:
Molded construction supports a higher current handling capability.
Iron-�powder material enables soft-�saturation
Magnetically shielded
Ultra low EMI due to molded construction
Available in Tape and Reel
Easy comparison of inductors in Wurth's simulation software "Component Selector"
Engineers are supported with eagle and altium libraries
PO
WE
R M
AN
AG
EM
EN
T
20 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
SMD Power Inductor, Compact Design with High Saturation CurrentAchieves up to 30A saturation in a small 4mm x 4mm package.
Size A (mm) B (mm) C (mm) D (mm) E (mm)
4020 4.45 4.06 1.8 0.76 2.0
7030 7.3 6.6 2.8 1.8 3.0
7050 7.3 6.6 4.8 1.8 3.0
1040 11.0 10.0 3.8 2.3 3.0
1335 13.5 12.6 3.3 2.3 3.0
http://www.nuhorizons.com/mobile/portal.php?pid=4_2011_gennum_fp
Renesas has partnered with IAR Systems to deliver engineers a power-house combo of low-power devices and high-quality software. They’re steering a great, green revolution and are challenging you to transform how the world experiences energy effi ciency by developing a unique, low-power application using the RL78 MCU and IAR toolchain. Succeed and win a share of $20,000 in cash prizes!
The competition started March 26, 2012 and ends on August 31, 2012. Winners will be announced in October at Renesas’ DevCon 2012.
Hundreds of free RL78/G13 development kits, loaded with IAR’s Kickstart edition, are being distributed to those who qualify. Quantities are limited so don’t delay! Be the green you see in the world and get ready for the RL78 Green Energy Challenge.
TheRL78
Green EnergyChallenge
For complete details, visit
www.circuitcellar.com/RenesasRL78Challenge
In association with Elektor and Circuit Cellar
Earn additional prizes like development tools, Pmods, Wi-�Fi modules, embedded systems books, and more from contest partners through weekly prize drawings. Follow Renesas on Twitter and Facebook for contest updates. @RenesasAmerica
Offi cial Contest Partners: Analog Devices, Inc., CMX Systems, Inc., Exosite, GainSpan Corporation, IAR Systems, Micrium, NDK Crystals (Nihon Dempa Kogyo Co., Ltd.), Okaya Electric Industries Co. Ltd., and Total Phase, Inc.
PO
WE
R S
UP
PL
IES
22
Scan barcode for more XL375 CC product information
For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
XL375 CC - 260 Watts without FansConvection Cooling Option Delivers 260 Watts Without Fans
The new Convection Cooling Option for the XL375 family delivers 260 watts across all output voltages and eliminates the fans and fan controllers needed to cool conventional power supplies, saving cost and freeing up valuable component space. Doing away with fans and related components and circuitry is significant to designers tasked with increasing the MTBF and decreasing the noise of products (fans may fail, and they generate most of the audible sound in contemporary designs).
OEMs can design in both convection-�cooled and fan-�cooled power supplies that use the same very compact, low profile 3.3” x 5” x 1.5” packaging, connectors and layout, saving time and cost. The very low profile packaging is ideally suited to 1U product designs and makes the system designer’s job much easier.
The Convection Cooling Option gives OEMs a distinct packaging and cost benefit while also reducing overall power consumption and cooling requirements for applications such as industrial automation, telecommunications, gaming systems, security and surveillance systems, and network servers. Our unique technology gives OEM engineers new flexibility in power system design that pays real competitive dividends in their final products.
All models also include Active Current Sharing to allow up to four supplies to be operated in parallel for high output applications. The Active OR-�ing mosfet board option is available for N+1 applications. Both 5V standby and 12V auxiliary outputs can be wired Or-�able when the main output is disabled. Synchronous rectification delivers exceptionally high efficiency: up to 93% in some models.
FEATURES:
Up to 93% efficiency
High power density
All outputs may be paralleled
Remote On / Off
5V Standby (1A)
12V Aux output
Universal AC input
Active current sharing for N, N+1 (main output)
OR-�ing mosfet board option
Active inrush current protection
Active PFC (90 -� 264 VAC)
BENEFITS:
No fans means higher reliability
Eliminating fans reduces noise
Small size ideally suited for 1U chassis designs
TYPICAL MECHANICAL DRAWING:Inches (millimeters)
Screws shown for reference only
1.50 (38.1)
.75(19.1)
XL375 AC - DCHeight = 1.50 (38.1)
J15 (–)
J204
J1
J14 (+)
5.00(127.0)
4.55(115.6)
2.55(64.8)
3.33(84.6)
.225(5.7)
.39(9.9)
APPLICATIONS:
Servers
Controllers
Switches
Test equipment
Industrial automation
Gaming systems
Security and surveillance systems
www.nuhorizons.comwww.nuhorizons.com1-888-747-NUHO (6846)
HLG series 40W ~ 320W• 95% high efficiency / PFC / IP65~67 / 277VAC / 4KV surge / 3-in-1 dimming(B-type)
PLN/HLN series 20W ~ 96W• PFC / 277VAC / IP64 / Class 2 / 3-in-1 dimming (HLN-B type)
PLC series 30W ~ 96W• 90% high efficiency / PFC / Class 2
display• Screw terminal style of I/O
LPF series 16W ~ 90W• 91% high efficiency / PFC / IP67 / 277VAC / Class II input / 3-in-1 dimming(D-type) / Class 2
LP series 18W ~ 100W• IP67 / Class II input / Class 2 (18~60W)
APV/APC series 12W ~ 35W• Class II input / Class 2• Constant voltage design(C.V. mode) for APV series• Constant current design(C.C. mode) for APC series
PCD/PLD series 16W/25W• PFC / AC phase-cut dimming / Work with leading edge and trailing edge TRIAC dimmers• Non AC dimming for PLD-25
CLG series 60W ~ 150W• 91% high efficiency / PFC / IP65~67 / 277VAC / 4KV surge
CEN series 60W~96W• 91% high efficiency / PFC / IP66 / 277VAC / 4KV surge / Class 2
HVG/HVGC series 100W• Wide input range: 180~480VAC • 92% high efficiency / PFC / IP67 / 3-in-1 dimming(B-type)•
LDV series 185W
• PFC / IP67 / 277VAC• Built-in DC/DC driver ICs in LDV-185
PLP/HLP series 20W~80W• PFC / PCB type / 277VAC / 3-in-1 dimming (HLP)
APPLICATIONS:
Servers
Controllers
Switches
Test equipment
Industrial automation
Gaming systems
Security and surveillance systems
Designers of handheld, battery-�based consumer products have long awaited a
programmable logic solution that delivers design fl exibility and fast time-�to-�market
benefi ts coupled with features that address their power, logic capacity, cost, and
small form factor requirements. This solution, previously unattainable by other FPGA
suppliers, is now provided by Lattice's ultra-�low power mobileFPGA™ devices.
Utilizing the mobileFPGA platform, mobile designers can quickly bring new
features and custom functionality to market with their very own Custom Mobile
Device. Designers can achieve this by either using state of the art development
software or by utilizing Lattice's design services.
FEATURES: Ideal for sensor management functions including interrupt fi ltering, interrupt aggregation, auto polling
Battery insertion and audio insertion detection with high speed comparators
Support MIPI SLIMbus Interface
High speed LVDS channels up to 525 Mbps per channel
High defi nition video support: HD720p @ 60Hz, HD1080p @ 30Hz
Supports MIPI DBI and MIPI DPI video interface standards
High Speed USB 2.0 host and device controllers supporting ULPI and UTMI interfaces
Ideal for 3D solutions
PCB friendly footprint packages
Fabricated on advanced 40nm standard CMOS process
50% faster than iCE65™ devices
Ultra-�low power consumption
Ultra-�small footprint packages
World's fi rst 2.5 x 2.5 mm, 0.4mm pitch ball grid array
2X logic capacity per mm2 over iCE65
Up to 2 phase-�locked loops supporting dual outputs
Flexible block RAM
SENSOR MANAGEMENT EXAMPLE:Offl oad sensor management functions from Application Processor
to Lattice Custom Mobile Device (CMD) to conserve system power
(keep AP in low power, sleep mode).
Interrupt Filtering
Interrupt Aggregation
Auto Polling
VIDEO AND IMAGING EXAMPLE:Drive different video peripherals from the same Application
Processor video stream.
Upscale/downscale video to drive different resolutions
High speed 525 Mbps LVDS supports
HD720p 30/60 Hz or HD1080p 30Hz resolution – single LVDS
WUXGA (1920 x 1200) at 60Hz -� dual LVDS
Scan barcodefor more iCEinformation
Lattice iCE FamilyMobileFPGA Platform
Feature LP Series (Low Power) HX Series (High Performance)
LP640 LP1K LP4K LP8K LP16K HX640 HX1K HX4K HX8K HX16K
Logic Cells 640 1280 3520 7680 16192 640 1280 3520 7680 16192
EBR RAM (Kbits) 32 64 80 128 384 32 64 80 128 384
PLL 1 1 2 2 2 1 1 2 2 2
Typical Core Current (μA) @ 0 KHz; 1.2V VCC
35 40 140 160 250 200 267 267 1100 2500
PR
OG
RA
MM
AB
LE
LO
GIC
24 For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal
PR
OG
RA
MM
AB
LE
LO
GIC
For more information, including pricing, availability, datasheets and samples (if available), please visit www.nuhorizons.com/portal 25
The MachXO2™ family of non-�volatile infi nitely reconfi gurable Programmable
Logic Devices (PLDs) is designed for applications such as telecommunications
infrastructure, computing, industrial, medical equipment and consumer. Combining
an optimized lookup table (LUT) architecture with 65-�nm embedded Flash process
technology, MachXO2 devices provide a fl exible “do-�it-�all” solution for system
designs.
MachXO2 devices include hard implementations of two I2C and one SPI interface
cores, and a timer/counter. All functions are accessible both externally and within
the device through the Embedded Function Block (EFB). Using MachXO2's hardened
block functions can save up to 600 LUTs for additional logic implementation.
HARDENED I2C IP CORE: Two I2C IP cores
Confi gurable Master/Slave mode
Support 7-�bit and 10-�bit addressing
Support multi-�master arbitration
Support clock stretching
Up to 400KHz data transfer speed
General call support
Interface to custom logic through 8-�bit WISHBONE interface
HARDENED TIMER/COUNTER: Supports four modes of operation
Watchdog timer
Clear timer on compare match
Fast PWM
Phase and frequency correct PWM
Programmable clock input source
Programmable input clock prescaler
One static interrupt output to routing
One wake-�up interrupt to on-�chip standby mode controller
Three independent interrupt sources
Overfl ow
Output compare match
Input capture
Waveform generation on the output
Internal WISHBONE bus access to the control and status register
Stand-�alone mode with preloaded control registers and direct reset input
HARDENED SPI IP CORE : Confi gurable Master and Slave modes
Full-�duplex data transfer
Mode fault error fl ag with CPU interrupt capability
Double-�buffered data register
Serial clock with programmable polarity and phase
LSB fi rst or MSB fi rst data transfer
Interface to custom logic through 8-�bit WISHBONE interface
Scan barcode for more Mach XO2
information
MachXO2 FamilyLow Cost, Low Power PLD
Flash MemorysysCLOCK PLLs
Programmable Function Units
Embedded Functional Block
On-chip Flash Memory
sysMEM Blocks
sysIO Buffers
Asymetrical I/O Banking
SPI I2C I2C Timer
WISHBONE BUS
MachXO2 Fabric
External I/O
Feature XO2-256 XO2-640 XO2-640U XO2-1200 XO2-1200U XO2-2000 XO2-2000U XO2-4000 XO2-7000
Density LUTs 256 640 640 1280 1280 2112 2112 4320 6864
EBR RAM (Kbits) 0 18 64 64 74 74 92 92 240
EBR RAM Blocks (9 Kbits/Block) 0 2 7 7 8 8 10 10 26
Distributed SRAM (Kbits) 2 5 5 10 10 16 16 34 54
User Flash Memory (Kbits) 0 24 64 64 80 80 96 96 256
PLLs 0 0 1 1 1 1 2 2 2
26
LED
Driv
ers
Mat
rix h
ighl
ight
ing
LEDs
/ Ch
anne
lLE
D Dr
iver
Spec
ial F
eatu
res
Appl
icat
ion
Regu
lato
r Top
olog
yNu
mbe
r of
Chan
nels
LEDs
/Ch
anne
lVL
ED M
ax (V
)Di
mm
ing
Open
Sho
rt
Dete
ctio
n Pr
otec
tion
Over
volta
ge
Prot
ectio
nAc
tive
Curr
ent
Shar
ing
Over
tem
p Pr
otec
tion
Unde
r Vol
tage
Lo
ckou
t
Alle
gro
Gene
ral B
ackl
ight
ing
Boos
t, Bo
ost C
ontro
ller
2-�8
12-�
3255
VY
YY
YY
Y
Auto
mot
ive
Back
light
ing
Boos
t 1
-�8 9
-�14
55V
YY
YY
YY
Auto
mot
ive
Ligh
ting
Buck
-�Boo
st, B
oost
, Lin
ear
1-�4
2-�1
540
VY
YY
YY
Y
Atm
el
TV B
ackl
ight
ing
NA 6
-�16
12Va
riabl
eY
YN
YY
N
TV E
dge-�
Lit B
ackl
ight
ing
NA 4
-�16
Varia
ble
Varia
ble
YY
NY
NN
Indu
stria
l Dis
play
Bac
klig
htin
gNA
612
Varia
ble
YY
YY
NN
Note
book
Bac
klig
htin
gNA
612
Varia
ble
YY
YY
NN
Mon
itor B
ackl
ight
ing
NA16
10Va
riabl
eY
YN
YY
N
Solid
Sta
te L
ight
ing
NA 4
-�16
Varia
ble
Varia
ble
YY
NY
NN
IXYS
Back
light
ing
Boos
t, Ch
arge
Pum
p 1
-�10
8Va
riabl
eY
YY
NY
Y
Flas
hCh
arge
Pum
p2
1Va
riabl
eY
YY
NY
Y
Off-�
Line
Hig
h Br
ight
ness
Boos
t, Bu
ckVa
riabl
eVa
riabl
eVa
riabl
eY
NN
NN
N
Line
ar T
echn
olog
y
Gene
ral
Boos
t 1
-�16
6-�2
5+Va
riabl
eY
YY
YY
Y
Gene
ral
Buck
1-�3
2 2
-�25+
Varia
ble
YY
YY
YY
Gene
ral
Boos
t-�Bu
ck 1
-�7 1
-�25+
Varia
ble
YY
YY
YY
Gene
ral
Mul
ti 1
-�4 6
-�25+
Varia
ble
YY
YY
YY
Gene
ral
uMod
ule
1 4
-�10
Varia
ble
YY
NY
YY
Offl i
ne
Flyb
ack
1Va
riabl
eVa
riabl
eY
YN
YN
N
Char
ge P
ump
Char
ge P
ump
1-�1
7 1
-�8Va
riabl
eY
YN
YY
Y
Shar
p
Para
llel L
EDs
Char
ge P
ump
161
120
YN
NY
YN
Serie
s LE
DsCh
arge
Pum
p18
9Va
riabl
eY
NN
YN
Y
Tele
funk
en
Para
llel L
EDs
Boos
t13
36V
YY
YNA
YY
Serie
s LE
DsBo
ost
110
6VY
YY
NAY
Y
27
LED
Driv
ers
Mat
rix h
ighl
ight
ing
LEDs
/ Ch
anne
lLE
D Dr
iver
Spec
ial F
eatu
res
Appl
icat
ion
Regu
lato
r Top
olog
yNu
mbe
r of
Chan
nels
LEDs
/Ch
anne
lVL
ED M
ax (V
)Di
mm
ing
Open
Sho
rt
Dete
ctio
n Pr
otec
tion
Over
volta
ge
Prot
ectio
nAc
tive
Curr
ent
Shar
ing
Over
tem
p Pr
otec
tion
Unde
r Vol
tage
Lo
ckou
t
Alle
gro
Gene
ral B
ackl
ight
ing
Boos
t, Bo
ost C
ontro
ller
2-�8
12-�
3255
VY
YY
YY
Y
Auto
mot
ive
Back
light
ing
Boos
t 1
-�8 9
-�14
55V
YY
YY
YY
Auto
mot
ive
Ligh
ting
Buck
-�Boo
st, B
oost
, Lin
ear
1-�4
2-�1
540
VY
YY
YY
Y
Atm
el
TV B
ackl
ight
ing
NA 6
-�16
12Va
riabl
eY
YN
YY
N
TV E
dge-�
Lit B
ackl
ight
ing
NA 4
-�16
Varia
ble
Varia
ble
YY
NY
NN
Indu
stria
l Dis
play
Bac
klig
htin
gNA
612
Varia
ble
YY
YY
NN
Note
book
Bac
klig
htin
gNA
612
Varia
ble
YY
YY
NN
Mon
itor B
ackl
ight
ing
NA16
10Va
riabl
eY
YN
YY
N
Solid
Sta
te L
ight
ing
NA 4
-�16
Varia
ble
Varia
ble
YY
NY
NN
IXYS
Back
light
ing
Boos
t, Ch
arge
Pum
p 1
-�10
8Va
riabl
eY
YY
NY
Y
Flas
hCh
arge
Pum
p2
1Va
riabl
eY
YY
NY
Y
Off-�
Line
Hig
h Br
ight
ness
Boos
t, Bu
ckVa
riabl
eVa
riabl
eVa
riabl
eY
NN
NN
N
Line
ar T
echn
olog
y
Gene
ral
Boos
t 1
-�16
6-�2
5+Va
riabl
eY
YY
YY
Y
Gene
ral
Buck
1-�3
2 2
-�25+
Varia
ble
YY
YY
YY
Gene
ral
Boos
t-�Bu
ck 1
-�7 1
-�25+
Varia
ble
YY
YY
YY
Gene
ral
Mul
ti 1
-�4 6
-�25+
Varia
ble
YY
YY
YY
Gene
ral
uMod
ule
1 4
-�10
Varia
ble
YY
NY
YY
Offl i
ne
Flyb
ack
1Va
riabl
eVa
riabl
eY
YN
YN
N
Char
ge P
ump
Char
ge P
ump
1-�1
7 1
-�8Va
riabl
eY
YN
YY
Y
Shar
p
Para
llel L
EDs
Char
ge P
ump
161
120
YN
NY
YN
Serie
s LE
DsCh
arge
Pum
p18
9Va
riabl
eY
NN
YN
Y
Tele
funk
en
Para
llel L
EDs
Boos
t13
36V
YY
YNA
YY
Serie
s LE
DsBo
ost
110
6VY
YY
NAY
Y
LED
Driv
ers
Mat
rix h
ighl
ight
ing
Curr
ent /
Cha
nnel
Appl
icat
ion
Regu
lato
r Top
olog
yNu
mbe
r of
Chan
nels
Curr
ent /
Chan
nel
VLED
Max
(V)
Dim
min
g Op
en S
hort
De
tect
ion
Prot
ectio
n
Over
volta
ge
Prot
ectio
nAc
tive
Curr
ent
Shar
ing
Over
tem
p Pr
otec
tion
Unde
r Vol
tage
Lo
ckou
t
Alle
gro
Gene
ral L
ight
ing
Buck
, Lin
ear
1-�1
650
mA-�
3A13
-�40
YN
NN
YY
ERG
Driv
er M
odul
esNA
810
0mA
60V
YY
YY
NY
Exar
High
Pow
er L
EDSt
ep D
own
12A
30V
YY
NNA
NY
Back
light
Boos
t, Ch
arge
Pum
p4
200m
A27
YY
NY
NY
Gene
ral
Line
ar8
100m
A30
VY
YN
YY
Y
Flas
hCh
arge
Pum
p3
1.45
A6V
YY
NN
YY
LED
Cont
rolle
rNA
431
.5m
A5.
5VY
NN
YY
Y
Mar
vell
Solid
Sta
te L
ight
ing
Buck
(DC-�
DC)
21A
Varia
ble
YY
YY
YY
Gene
ral P
urpo
seFl
ybac
k (A
C-�DC
)1
1.2A
Varia
ble
YY
YNA
YY
Mic
rel
Gene
ral P
urpo
seBo
ost,
Line
ar6
1.2A
40V
YN
YY
YY
Mic
rose
mi
Back
light
Boos
t8
200m
A40
VY
YY
YY
Y
ST Pow
er L
ED D
river
sNA
4-�1
640
0mA
20V
YN
NY
YY
LED
Fron
t Pan
el
Driv
ers
NA 4
-�16
20m
A33
VY
NN
YN
N
Supe
rtex
Auto
mot
ive
Buck
, Boo
st, B
uck-�
Boos
t,SEP
IC1
Varia
ble
75V
YY
YNA
YN
Gene
ral P
urpo
seBu
ck, H
yste
ric, S
ingl
e-�Sw
itch
PFC,
Fly
back
650
mA
220V
YY
YY
YN
Samsung + LED Lighting + Nu Horizons =
Innovative Lighting Solutions
LED Lighting Solutionsfrom
Samsung is committed to leading the LED lighting revolution, and Nu Horizons is committed to delivering the right solution to meet your LED project needs.
Mid-power white LEDs
High-power white LEDs
High-voltage white AC LEDs
High-voltage white DC LEDs
Light Engines and Modules
LED Tube
Let Nu Horizons be your design and manufacturing solution partner for your lighting needs. Learn more at www.nuhorizons.com/ledlighting or scan the
QR code below with your smart phone.
Design Custom LED Assembly
Let Nu Horizons be your design and manufacturing solution partner for your lighting needs. Learn more at
www.nuhorizons.com/ledlighting or scan the QR code below with your smart phone.
Lighting Technologies available from Nu Horizons
29
LEDs Samsung LED Sharp
Optics Ledil
Light Engines Samsung LED OptoElectronix
Thermal Management OptoElectronix LED Specialists
LED Drivers Allegro Atmel ERG Exar IXYS ISSI Linear Technology Marvell Micrel MicroSemi ST Supertex Telefunken
Power Solutions LHV Power Mean Well GE Energy N2Power
System Design Nu Horizons LED Lighting Solutions
LED Components: ■ Low power ■ Mid power ■ High power ■ HV AC ■ HV DC ■ Flash LED
Optics: ■ Lenses ■ Refl ectors ■ Standard products ■ Custom solutions ■ Development & deployment of new fi xtures
Light Engines: ■ LED street light ■ LED down light ■ LED area light ■ LED light strip
Thermal Management: ■ Thermal testing ■ Thermal management
LED Drivers ■ Inductorless white LED drivers (for LEDs in parallel) ■ Switching regulator based white LED drivers (for LEDs in series) ■ Integrated Schottky diodes ■ Accurate LED current matching ■ Multiple output capability ■ Topologies - Constant current source - Dimmable current source - Flyback - Boost (step-up) - Buck (Step Down) - LLC resonant topologies - SEPIC topology
Power Solutions ■ Fully assembled and tested power solution ■ Ruggedized products ■ End to end solutions - AC/DC - DC/DC ■ 6W to 320W ■ Norms - UL1310 Class 2, UL8750, EN61347-2-13, EN61000-3-2 Class C (harmonic current) and IP64~67
System Design ■ Nu Horizons LED Lighting Solutions - One stop solution for all your solid state lighting needs - Design - Custom LED - Assembly
Display Technologies available from Nu Horizons
30
Cable SolutionsQuadrangle
Displays Emerging Display Technologies (EDT) LG Display Optrex OSD D isplays Pervasive Display Sharp Tianma
Embedded Solutions / Single Board Computers
Aaeon Amulet Technologies Axiom Tek Connect Tech Digi International IEI Technology Reach Technology
Inverters Applied Concepts ERG Microsemi
LCD Controller Solutions Amulet Technologies Digital View Estecom-USA Kordis URT
LCD Monitors Axiom Tek Estecom-USA IEI LG Display Touch Revolution
Open Frame/Panel PC SolutionsAaeon
Axiom Tek Estecom-USA IEI T echnology Landmark Nu Horizons Custom Solutions Touch Revolution Touchscreens
Hantouch Touch International Touch Revolution
Active Enhancements: ■ Hi Bright Backlights: - CCFL - LED
Design Services: ■ System Hardware & Compatibility ■ Product Specifi cation ■ Custom Test Set-up ■ POC / Prototype ■ First Article ■ Revision Control (ECN) ■ Engineering Evaluation ■ Problem Resolution
Display Technologies: ■ LCD - Active, Passive - Graphic - Color, Monochrome - Character - 3D ■ EPD - e-Paper, e-Ink ■ OLED - Organic Light Emitting Diode ■ PID - Public Information Display, Signage
Passive Enhancements: ■ Anti-Refl ective Anti Glare Glass / Acrylic ■ EMI/RFI Shielding ■ IR Blocking Film ■ Optical Bonding ■ Privacy Filters ■ Protective Display Shields
Total Solutions: ■ Display Kit Verifi cation ■ Fully Enclosed LCD Monitors ■ Fully Enclosed LCD Systems (Panel PC’s) ■ LCD Testing and Screening ■ Medical ■ NEMA Rated Products ■ Open Frame Confi gurations ■ Rack and Panel Mount Assemblies
Touch Screen Integration: ■ Capacitive ■ Surface Acoustic Wave (SAW) ■ IR - Infrared Touch ■ Projected Capacitive - Extreme-Touch ■ Resistive - 4/5/8 Wire ■ Touch Controllers / Serial USB
Value-Add Capabilities: ■ Class 1,000 Clean Room for all LCD Enhancements ■ Display Inspection ■ NVIS Night Vision ■ Optical Glass Bonding ■ Touch Screen Integration ■ Functional Testing: - Power Cycling - Elevated Temperature Test - Video Testing / Calibration - Flat Panel - Pixel Screen - Extended Burn-in - Custom Test Creation / Execution - Touch Screen Calibration
T E C H N O L O G Y I N C .
w w w . n u h o r i z o n s . c o m / d i s p l a y s
Cable SolutionsQuadrangle
Displays Emerging Display Technologies (EDT) LG Display Optrex OSD D isplays Pervasive Display Sharp Tianma
Embedded Solutions / Single Board Computers
Aaeon Amulet Technologies Axiom Tek Connect Tech Digi International IEI Technology Reach Technology
Inverters Applied Concepts ERG Microsemi
LCD Controller Solutions Amulet Technologies Digital View Estecom-USA Kordis URT
LCD Monitors Axiom Tek Estecom-USA IEI LG Display Touch Revolution
Open Frame/Panel PC SolutionsAaeon
Axiom TekEstecom-USA
IEI T echnology Landmark Nu Horizons Custom Solutions Touch Revolution
TouchscreensHantouch
Touch International Touch Revolution
w w w . n u h o r i z o n s . c o m / d i s p l a y s
Embedded Solutions / Single Board Computers available from Nu Horizons
Offering Embedded Computing Platforms so that
customers have a single, reliable, cost-�effective source
to a wide array of CE, FCC & UL certifi ed products.
These products include single board computers,
embedded systems and barebone systems, panel
computers, medical PC, human machine interfaces, and
network security appliances.
T E C H N O L O G Y I N C .
Supported Markets Medical
Military
Heavy Industrial
Consumer
Gaming & Entertainment
Point of Sale
Telecom
Supported Processors Intel
VIA
Xscale
Marvell
AMD
System on Module ■ ETX
■ STX
■ Q7
■ COM EXPRESS
■ XTX
■ SOM Baseboards
Industrial Motherboards ■ Mini ITX
■ Micro ATX
■ ATX
Embedded SBC ■ Pico ITX
■ 3.5” Capa Boards
■ EPIC
■ 5.25 Boards
■ RISC CPU Modules
■ PC104
Servers Sun Micro
Super Micro
IBM
Panel PC/POS Solutions ■ Medical Grade Touchscreen Computers
■ Industrial Monitors
■ Digital Signage
■ Video Wall Controllers
■ Heavy Industrial Monitors
■ Rack Consol
■ RISC Based monitor
Peripherals ■ Memory (Flash, DDR, DDR2, DDR3)
■ Heatsink/Fan Assemblies
■ MiniPCI Module
■SA/PCI/PCI-X riser cards
■ I/O cables
■ LCD wiring kits
■ Compact Flash
■ HDD Drives
Add on Cards ■ LCD converter
■ FPGA
■ Video Capture
■ PCI-Express cards
■ PC104 I/O Modules
■ Wireless
■ RFID
■ Wireless Radio Modems
■ CAN Controllers
Chassis ■ 1U to 6U
■ Shoe Box
■ Rackmount
■ Compact
■ Embedded
Power Solutions ■ DC/DC
■ Open Frame
■ 1U/2U Power supply
■ UPS Module
■ AC/DC
Software Microsoft, Linux Support
Technical Resources / Customization Resources ■ Sheet Metail
■ Industrial Design
■ Silk Screening
■ Custom Enclosures
31
Semiconductor Technologies available from Nu Horizons
• Audio (DACs, ADCs, Codecs, SPDIF, Sample Rate Conv., DSP, USB)
• Memory (EEPROM, DAC + EEPROM) • Networking (T1/E1/T3/E3 xcvr, PCM)
• Sensors (Hall Effect Sensor, 3d Compass) • Video (NTSC/PAL Encoder/Decoder, A/V Switches, Video Gain Amp)
• Discrete (Transistors, FET arrays, Thyristors, Triacs)• Display (Vacuum – Fluorescent Display Drivers)
• LED Drivers (Constant Current Drivers) • Motor Control (Brushless DC, Bi-Polar Stepper)
• Power (Linear Regulators, Buck/Boost/Fly back DC- DC, Charge Pumps)
• Sensors (Hall Effect)
• Converters (Dynamically Programmed Analog Signal Processors (dpASP's), Field Programmable Analog Array’s (FPAA's)
• Analog (Data Conversion, Power Management)• Communications (Bluetooth, LIN, CAN, POTS,
GPS, RF, Zigbee)• Memory (Flash, EEPROM, Modules)• Microcontrollers (8051, AVR, ARM7TDMI,
ARM926EJ, Cortex M3)• Multimedia & Imaging (IR, Video)• Network Storage (Data Storage)• Programmable Logic (FPGA, SPLD/CPLD)• Sensors (Biometrics, RF, Smart Cards)
• Converters (ADCs, DACs)• Signal Conditioning (Amplifi ers, Comparators)• Video (Filters, Amplifi ers)
• Fiber Optic Devices (10G FP TOSA & MM PIN ROSA, OTDR FP Lasers, 2.5G DWDM DML, DFB TOSA & APD ROSA) • Optocouplers (Transistor Output, High Speed, Solid State Relays) • RF Modules (Zigbee) • RF Semiconductors (RFIC Switch, GaAs FET, GaAs PA, Si LD-MOSFET, CATV Hybrid, Si RFIC)
• Power and Battery Management (IGBT and MOSFET gate drivers) • Sensor and Imaging Arrays (Hall Effect Sensors) • Signal Conditioning (Solid State Relays, Optocouplers) • Telecom (Embedded Modem, MF Trunk signaling, DTMF)
• Imaging Solutions (Fax Modems, Fax and MFP System Solutions, Digital Photo Frames) • Audio (Speakers-on-a-Chip, PC HD-Audio, PC HD- Audio Modem Combo) • Video (MPEG Encoders/Codecs, Video Decoders, Demodulators, Surveillance / Security) • Dial-Up Access Modems (PC Dial-Up Modems, Embedded Dial-Up Modems)
• Wireless (Bluetooth modules, ZigBee modules, 802.11 modules)
• Device Server Modules • Embedded MCU / MPU (ARM7TDMI, ARM9926EJ) • Networking Modules (Wired/Wireless 802.3 / 802.11bg / 802.15.4)
• Data Converters (ADCs, DACs) • Interface (PLB / PCI / I2C / SPI / USB UARTs, RS232/485/422 Transceivers) • Power (Buck/Boost Regulator’s, Charge Pumps, LDO’s, Supervisors, PWM, Programmable Power) • Storage (Data Reduction, Data Security) • Telecom (T1/E1/DS1/DS3/E3 LIU’s, Carrier ETH SONET/SDH Framers, Mappers & Aggregators)
(Fiber Optics Division) • Optical Components (WDM Management, 850nm VCSELs & Detectors, 1310nm Lasers & Detectors, CML Transmitters,WSS) • Optical Transceivers (GBIC, XFP, MSA300, SFP, SFP+) • Passive Optics (WDM networks)
• AC-DC Power Supplies (800W - 4,000W) • DC-DC Converters - Industry Standard (1/16-Brick, 1/8-Brick, 1/4- Brick, 1/2-Brick, 1x1”, 2x1”) - Intermediate Bus Converters (1/8-Brick, 1/4- Brick) - Power Amplifi ers (1/2-Brick, Full Brick) • Power & Battery Management (Power Modules) • Power Systems Engineering Services
• Audio (SerDes with Emebed/De-Embed) • Datacom (Cable & Backplane SerDes, Redrivers, Retimers, PCIe Bridges, Crosspoint Switches, TIAs, LAs, Transceivers) • Video (Equalizers, Cable Drivers, Reclockers, SerDes, Video Optical Modules, TIAs, LAs, Laser Drivers, Timing, Crosspoint Switches, Cable Extenders)
• Memory (DDR DRAM,SDRAM, EDO & FPO DRAM, E2PROM, PSRAM, SRAM, DDR II Synchronous SRAM, Asynchronous SRAM) • Smart Card (Two-Wire Serial EEPROM, Secure, MCU Based, ICs)
• Power (MOSFET, IGBT, Diodes, Thyristors, DC/DC, PWM Control, LED/Lamp/Display Drivers) • RF Power (FETs, Drivers, Amplifi ers, Microwave modules, RF Modules) • Solar Devices (Solar Cells, Solar Bits, Solar Die, Solar Battery Chargers)
(Formerly Oki and Rohm Semiconductor) • Audio (CODECs, DACs, Amplifi ers ) • Display Drivers (LCD / VFD Driver / Controllers) • Embedded MCU / MPU (4-Bit NX 63K / ARM7TDMI / ARM946E / Biometrics) • Memory (P2ROM, DRAM ) • Speech (BGM Mixer - ADPCM & ADPCM2, Voice Synthesizers & Recorders, Audio Codec) • Telecom (ADPCM – Linear – PCMA-Law - VoIP Codec’s, Echo Cancellers, Transceivers) • Video (NTSC / PAL / SECAM Encoders – Decoders, NR-FIFO)
• Programmable Clock Devices (Clock Generation, Differential Clock Distribution, Universal Fanout & Zero Delay Buffer, Clock Synthesis, Low Jitter SERDES Clock) • Programmable Power Manager Devices (for Processors, DSPs & Board Level; Watchdog timer, Voltage Supervision, Reset Generation, Sequencing, Voltage Measurement, Trimming & Marginning) • Programmable Logic (Non-Volatile Flash FPGA, SRAM FPGA, SERDES, 8/32 Bit Soft Processor, Ultra-Low Power CPLD, SPLD)
• Power Supplies - High Voltage (1 to 5 W, 10 to 200 W, Custom) - Low Voltage (Modular, Desktop, Wallmount, Medical, Open-Frame, U-Frame, Enclosed, LED Lighting, Custom)
• Data Converters (Delta Sigma, SAR, Voltage DAC, Current DAC) • Frequency Control (Silicon Timing) • Interface (RS-232, 422/485, CAN PHY) • Power Management (Switching Regulators, Linear Regulators, DC/DC µModules, LED Drivers, Hot Swap, PoE) • Signal Conditioning (Amplifi ers, Comparators, Filters, Voltage References, Thermal Couple Compensators) • Wireless / RF (I/Q Modulators – Demodulators, Up & Down Converting Mixers, IF Amplifi ers, PA, RF Log Detectors, RF Power Detector)
• Video (Video Encoders, Transcoders, Decoders, SoCs, Coprocessors)
• Data Communications (10/100/1G/10G Ethernet Switches, 10/100/1000/10G PHYs) • Embedded MCU / MPU (ARM V5TE, PXA StrongARM, PPC & MIPS Systems Controller) • Power Management (POLA) • Storage (FAS/SATA/PATA, SAS/Fiberchannel, Storage Processors) • Video (Format Converter) • Wireless / RF (802.11 Modules)
32
• AC/DC Power Supplies (Enclosed, DIN Rail, Open Frame, LED, Modular, Rack Power, Charger, Adaptor, Specifi c Purpose)
• DC/DC Power Supplies (Modular, On Board, PBC, Enclosed)
• Analog (Drivers / Voltage & uC Supervisors / Filters / Switches / Regulators) • Bus Device ICs (USB / PC / PCMCIA / SMBus) • Ethernet (10/100/1000 PHYs, Controllers, Switches)
• Linear ICs (Active Filters / Comparators / Op Amps / References / Timers) • Power Management ICs (Battery, Display, Hot- Swap, PCI/PCIX/PCIE, High Side, LDOs, DDR)
• Precision Edge ICs (Clock distribution, generation, synthesizers / Multiplexers, PLLs, buffers, CDRs) • RF (290 – 980 ISM band / ASK/FSK / 200kbps max data rate, RF Modules) • System Management ICs (Fan Control / Thermal Supervisor I2C)
• DRAM (DDR3 SDRAM, DDR2 SDRAM, DDR
SDRAM, SDRAM, RLDRAM, PSRAM)• DRAM Modules (FBDIMM, RDIMM, SODIMM,
UDIMM) • Mobil DRAM (Mobil SDRAM, Mobil DDR SDRAM)
• Multichip Packages (MobilDRAM & NAND Flash Combinations) • NAND Flash Memory (Managed NAND, High Speed NAND, Solid State Storage, Embedded USB)
(Formerly C&D Technologies)
• AC/DC Power Supplies (200 – 2000 Watts, 2.5VDC to 48 VDC Out – PCI Modules)
• Data Acquisition (Electronic Imaging, A/D Converters, D/A Converters, Sample/Hold Amplifi er, Multiplexers) • DC/DC Converters (0.25 to 340 Watts, 0.02 to 80 Amps, 1.2 to 48 VDC Out; 3 to 75 VDC In)
• Digital Panel Meters (Voltmeters, Wire Meters, Process Monitors, AC/DC Ammeters) • Magnetics (Inductors & Transformers, Differential common-mode fi lters, Databus Isolators)
• AC-DC Power Supplies (125W-375W, 3.3vdo to 56vdo, 90-264vao in, 3”, 3.3” x 5” format)
• DC-DC Open Frame Power Supplies (125W, 160W, 3.3-48vdo 3” X 5” format)
• Power Systems Engineering Services
• Wireless/RF (2.4G / 900M / 433M Transceiver, MCU based RF, Audio streaming)
• Communications (Voice & Audio CODECs, Pro-X SLICs, USB Audio Codec) • Logic ICs (I/O Controllers, ISA Bridge, Power Management, Hardware Monitors, Clock Generators, Power I/C, Card Reader IC’s, IEEE1394) • MPU (8-bit 80C51 based, 32-bit ARM7TDMI)
• Power (ACPI Controller, PWM, DDR Bus Term, Power Switch) • Voice Solutions (Record & Playback ICs)
• Analog Image Sensor (NTSC/PAL) • Digital Image Sensor (CIF, VGA, 1.3M / 2.0M / 3.2M / 5.17M Pixel) • Image Processors
(Including SaRonix)
• Analog Switches (3-17V SPDT-SPST-DPST-MUX, Custom HDMI/DVI-PCI-USB-LAN) • Bridges (PCI, PCIX, PCI Express – 32/64Bit – 66/133MHz) • Clock ICs ( VCXOs, Buffers, Drivers, Generators, Skew Controllers) • Crystals & Oscillators (Quartz Crystal Resonators) • Digital Switches (2-Port, Bus, Crossbar, DDR, Mux/DeMux, Low Voltage Translator) • Interface (Re-Drivers, Buffers, Flip-Flops, Gates, Latches, Registers, Transceivers, Voltage Translators) • Logic (ALVC, FCT, LCX, LPT) • PCI Express Solutions (Packet/Signal Switches, Bridge, PHY, Signal Conditioning, Clock-Buffers/ Generators/Crystals) • Translators (Voltage, I/O Signal)
• Frequency Control (Oscillators, Crystals, VCXO, TCXO, OCXO, Sine Wave Oscillator)
• Communications (CAN, LIN, ZigBee) • Discrete (Diodes, Power MOSFETS, Thyristors, Triacs, Transistors) • Embedded MCU / MPU (8/16/32 Bit MCUs) • Logic (Standard – High/Low Voltage, Interface, Multi-Purpose) • Memory (Fast Flash, Low Power SRAM, EEPROM)
• Optoelectronics (LED Modules/Arrays, LED Tube, Outdoor Lighting, BLU, Automotive) • LEDs (Middle Power, High Power, Flash LED)
• Power (High Reliability Transistors)
• Flat Panel Displays (LCD – 2” to 65”) • Memory (Flash – NOR) • Optoelectronics (LEDs, LED Modules, Laser Diode, Photocoupler, IrDA, photo interrupters, Emitters/ Detectors, Sensors) • Power (LDO / Switching Regulators, LED Drivers, Solid State Relays)
• Digital Video Processors • Storage Products (Serial ATA - Parallel ATA, Parallel ATA Controller, RAID Storage Processors, SATA Controllers, SATA Port Multipliers) • Video Transport (HDMI, DVI and iTMDS Products - Receivers, Transmitters, Switches, PHYs)
• Controllers (Flash Memory Card Controller, USB Flash Controller) • Embedded Graphics (128-bit 2D/3D mobile graphics engine, Mobile Graphics Coprocessor) • Mobile Communication (Mobile Satellite TV Tuner IC) • Multimedia SoC (MP3/WMA Digital Audio Player, USB 2.0 Megapixal Image Controller)
• Advanced I/O Controllers (USB-ATA, Southbridge) • Data Communications (10/100 MAC/PHY Controller, 10/100PHY, Multimedia Processors, ArcNET, CircNET, USB Ethernet) • Environmental (Temperature Sensors, Fan Control) • USB Solutions (Card Reader, Flash Drive, Disk Drive, Hub, PHY)
• Power Management (AC/DC, Battery Management, DC/DC, LDO, MPU - Supervisor, PoE, VDC References, AC Switches) • Discretes (Thyristors, Diodes, FETs, Transistors) • Signal Conditioning (Comparators, Op-Amps, Clamp Diode Arrays, Crowbar Diodes, EMI Filtering) • Logic (3.3V, 5V, Translators, Gates, Switches, Port - Expansion) • Sensors (Accelerometers, Proximity, Thermal, Touch) • Interface (Smartcard) • Wireless (Bluetooth, ZigBee, GPS, RFID) • Audio (Decoders, Power Amps, Analog CPU, Digital CPU, Radio) • Image Sensor (Camera Modules, Imaging Signal Processor, CMOS Arrays) • Video (Demodulator, Decoders) • Motor Control (Controllers, Drivers, MCU’s) • Microcontrollers (8-bit, 16-bit, ARM7TDMI, ARM926E, Cortex M3)
• Optoelectronics (LED Drivers, EL Lamp Drivers) • Power (Switching, Automotive, PFC, Backlight, LDO, High Voltage Interface / Driver’s, PoE) • Transducers (Ultrasound)
• AC/DC Power Supplies (Industrial and Medical - 300W - 1500W) • DC/DC Converters - Industry Standard (1/8-Brick, 1/4-Brick, 1/2- Brick, Full Brick) - Non-Isolated Point of Load - Intermediate Bus Converters (1/8-Brick, 1/4- Brick, 1/2-Brick)
• Switching Regulators (AC-DC and Step-up, Step- down DC-DC Switching Regulators, LED Drivers) • Gate Drivers (600V High & Low side Drivers, Half Bridge Drivers) • Interface (Extended Common Mode LVDS, Crosspoints, M-LVDS) • System Test (JTAG Muxes)
• Memory (SDRAM / DDR1, Pseudo SRAM, Serial Flash, Parallel Flash)
• Filters • Inductors • Isolators • Transformers (Modem, Analog/Voice Switching, DSL, Cable Modem, RJ45, PoE)
• AC/DC Power Supplies (Medical, Easy Swap, 1U, 2U, 3U, PS2, PS2+) • DC/DC Power Suppliers (Open Frame)
33
ExarLinear TechnologyMicrelNuvoton
SMSCSTTelefunken
Exar SMSC
SYSTEM MONITORING
Clock DistributionExarLatticeMicrelPericomST
Clock GenerationAKM SemiconductorExarGennumLatticeLinear TechnologyMicrelPericom / SaRonixPletronics
Crystals, Oscillators, Drivers, Buffers, PLLs
TIMING
A/D AKM SemiconductorCadekaExarLinear TechnologyMurata Power SolutionsNuvotonST
D/AAKM SemiconductorCadekaLinear TechnologyMurata Power SolutionsST
CONVERTERS8-BitAtmelISSILapis SemiconductorLattice (soft processor)NordicNuvotonRenesas ST
16-BitRenesasST
CENTRAL PROCESSOR
POWER & BATTERY MANAGEMENTBattery ManagementAllegro MicroSystemsLinear TechnologyMicrelST
DiscretesAllegro MicroSystemsIXYSMurata Power SolutionsRenesasSemicoaSTSupertexWurth Midcom
Hot SwapLatticeLinear TechnologyMicrelSupertex
Linear Regulators &ReferencesAllegro MicroSystemsAtmelExarLapis SemiconductorLinear TechnologyMarvell (modules)MicrelSharp MicroelectronicsSTSupertex
Motor ControlAllegro MicroSystemsSTTelefunken
POELinear TechnologySTSupertex
Power ManagementExarIXYSLatticeLinear TechnologyMarvellMicrelMurata Power SolutionsSTTelefunken
Power Modules GE EnergyLinear TechnologyMarvellMurata Power SolutionsSynQor
SwitchingAllegro MicroSystemsExarLapis SemiconductorLinear TechnologyMarvellMicrelSTSupertexTelefunken
Allegro MicroSystemsAKM Semiconductor AtmelClareLapis SemiconductorNuvoton
OmnivisionSharp MicroelectronicsSMSCST
SENSORS AND IMAGING ARRAYS
DiscretesSTWurth Midcom
DriversGennumMicrelSTSupertex
Amplifi ersCadekaLinear TechnologyMicrelST
IsolationCELClarePericomSharp MicroelectronicsST
ComparatorsCadekaLinear TechnologyMicrelST
FiltersLinear TechnologyMicrelSTWurth Midcom
SIGNAL CONDITIONING
POWER SUPPLIESAC-DC Low Power LHV PowerMean WellMurata Power SolutionsN2PowerZippyMedium Power LHV Power Mean Well Murata Power SolutionsN2PowerSynQorZippyHigh Power GE EnergyLHV Power Mean Well ZippyFront End GE EnergyLHV Power Mean Well Murata Power SolutionsZippyMedical LHV Power Mean Well SynQorZippy
DC-DC Industrial Isolated / Industry Standard Bricks /Non-Isolated Point of LoadGE EnergyLHV Power Mean WellMurata Power SolutionsSynQor
Open FrameLHV Power Mean Well N2PowerZippy
Board Level ModulesIntermediate Bus ConvertersGE EnergyMurata Power SolutionsSynQor
Memory & Processor PowerMurata Power Solutions
InfraredSharp Microelectronics
LasersFinisar
LED DisplaysOptrexMurata Power Solutions
LED Arrays / ModulesSamsung LEDSharp Microelectronics
LEDs / Laser DiodesSamsung LEDSharp Microelectronics
Optical SystemsCELFinisarGennum
OptoCouplersCELSharp Microelectronics
OPTOELECTRONICS
34
dpASP Anadigm
FPAAAnadigm
8-BitAtmelISSILapis SemiconductorLattice (soft processor)NordicNuvotonRenesas ST
16-BitRenesasST
32-BitAtmelDigiLapis SemiconductorLattice (soft processor)MarvellNuvotonRenesasST
CENTRAL PROCESSOR
ModemConexantST
VoIPLapis SemiconductorMarvellNuvoton Renesas
TransceiversClareExarFinisarGennumMarvellST
TELECOMCentral Offi ce(CODECs, SLICs, DAA, xDSL)AtmelClareConexantExarLapis SemiconductorNuvoton RenesasST
SwitchingExar
ISMAtmelLattice MicrelNordicST
RFIDAtmelLattice ST
802.11 a/b/g/nConnectBlueDigiMarvellSharpST
MicrowaveCELIXYSLattice
BluetoothConnectBlue
ZigBeeAtmelCELConnectBlueLapis SemiconductorRenesasST
Discretes (RF)AKM SemiconductorAtmelCELIXYSLTCMicrelSTWurth Midcom
GPSAtmelST
WiMaxSharp Microelectronics
WIRELESS
ParallelLattice NuvotonPericom
Low Speed Serial (under 1 MB/sec) Exar Lapis SemiconductorLattice Linear TechnologyMicrelRenesas SMSC STTelefunken
High Speed Serial(above 1 MB/sec) GennumLattice MarvellMicrelPericom Renesas SMSCSTTelefunken
Level TranslatorsAtmelLattice Linear TechnologyMicrelPericomST
BUS INTERFACE
DATACOMEthernet MACMarvellMicrelSMSC ST
WAN / TransportExarGennumMarvell
Ethernet SwitchingMarvell
USBRenesasSilicon MotionSMSC
OpticalConexantFinisarGennum
Non-VolatileEPROMAtmelLapis SemiconductorST
E2PROMAKM SemiconductorAtmelISSIRenesasST
FlashAtmelISSIMicronRenesasSharp MicroelectronicsWinbond
Storage ControllersSilicon MotionSMSC
VolatileDRAMISSILapis SemiconductorMicronWinbond
SRAMAtmelISSIRenesasSharp MicroeletronicsSTWinbond
FIFOLapis Semiconductor
MEMORY
ASICAtmel
CPLDAtmelLattice
FPGAAtmelLattice
LOGICSPLDAtmelLattice
StandardMurata Power SolutionsPericomRenesasST
LOGIC
EthernetLatticeMarvellMicrelSMSCST
Transformers / IsolatorsWurth Midcom
PHYSICAL LAYER
AKM SemiconductorCadekaConexantGennumLapis SemiconductorLattice Magnum
MarvellNuvotonOmnivisionSilicon ImageSilicon Motion ST
AUDIO / VIDEO
DISK / INTERFACESAS/SCSIMarvell
SATA/ATAAtmel Exar MarvellSilicon ImageSMSC
FibreChannelLattice Marvell
Solid StateMicronSilicon MotionSMSC
35
LabCam delivers online training opportunities in a way that recognizes the value of engineers’ time. As easily as You Tube® videos, engineers can quickly load and watch videos from industry leaders consisting of insights on products, evaluation kit overviews, end-user applications and more. Each tutorial is up to ten minutes in length and features technology experts, CEOs and/or peers introducing new solutions or explaining integral aspects of an important product, solution or application. This free value-added program is packaged for short, informative and high quality distance learning.
Nu Horizons is proud to present our education and training program, which offers engineers the opportunity to participate in technical seminars conducted by experts focused on the latest technologies from our leading suppliers. This program provides higher velocity learning to help minimize start-up time to quickly begin your design process utilizing the latest development tools, software and products. Check online for the latest seminar schedule.
In order to simplify the design process, Nu Horizons has created a series of application notes designed to guide engineers through the process of interfacing different devices together. Using a detailed step-by-step approach, these design guides identify key elements in the design process. Topics in the application notes are organized by design task and each topic is a stand-alone section, with a short introduction or overview, followed by the step-by-step design guidelines. All steps include a suffi cient level of detail to provide the designer with relevant information to proceed quickly and easily from start to fi nish.
Nu Horizons offers a wide range of development / evaluation boards, tools and kits featuring the latest technology from the most trusted suppliers in the industry. Visit the development tool section of our website for a variety of solutions all aimed at providing a low-cost solution for designers to accelerate a product’s time-to-market.
www.nuhorizons.com/labcam
www.nuhorizons.com/seminars
www.nuhorizons.com/appnoteswww.nuhorizons.com/appnotes
Application Notes
DevelopmentTools
www.nuhorizons.com/devtoolswww.nuhorizons.com/devtoolswww.nuhorizons.com/devtoolswww.nuhorizons.com/devtools
Portal is a quarterly publication containing new products, technologies and development tools available from Nu Horizons leading suppliers. Portal is availabe both in print and on the web. Sign up online to receive your copy, be notifi ed of upcoming issues or to request samples of the products found inside.
www.nuhorizons.com/portal
Enhance Your Design...WITH NU HORIZONS EDUCATION AND DEVELOPMENT SOLUTIONS