oasis curved bar - crown spas
TRANSCRIPT
oasis curved bar
ston
e oa
sis
colle
ctio
n
instruction guide
2
This kit measures 80”W x 30”D x 43”H.
Materials Included:standard 12” radius quarry stone - 65 pcsstandard 12” radius quarry stone half pieces - 8 pcsstandard 12” radius quarry stone cut to 7” marked with an X - 2 pcsquarry stone 8x12 - 16 pcsquarry stone 4x8 - 16 pcs countertops - 2 pcsshims1 tube of glueglovesinstruction guideinstallation videolandscape design plan
Tools Required:caulking gunlevelrubber mallet (optional)
*This kit contains extra pieces. You will have pieces left over once you have completed the install.
Note: If installing your oasis curved bar on an unstructured base, please be sure to follow these steps:• Excavate area approx. 5” below grade• Excavate approx. 6” larger than your
actual kit dimensions to ensure a stable base
• Fill 4” with 3/4” down limestone and compact
• Level out 1/2” of sand and install kit as per the instruction guide
If you are installing on an existing patio and/or the base prep is not necessary, then you can proceed to the first step on the following page.
standard 12” radius quarry stone
standard 12” radius quarry stone half pieces
quarry stone 8x12 quarry stone 4x8
countertop 3” x 20” x 6’
countertop 3” x 15” x 7’6”
12” radius cut to 7”
3
1. On your level-prepared surface, lay out pattern A to form the first layer.
Note: Ensure that this layer is level to facilitate a proper installation. Consult the previous page for more info.
2. Lay out the step pattern to form the second layer.
3. Put the step pattern on top of pattern A. Glue the four pieces that make up the step and make sure the middle portion sticks out by approximately 3” as shown.
Note: Use the marked pieces provided for the edges of the step pattern.
pattern A
step pattern
12” radius quarry stone cut to 7”
4
4. Lay out pattern A to form the 3rd layer.
5. Alternate between pattern A and pattern B until you have completed 8 layers.
6. This image represent the oasis curved bar with layers 1-8 complete. Glue the last layer to provide a solid base for the smaller countertop.
pattern A
pattern B
5
7. Lay out pattern A and pattern B using only the tapered quarry stone (as shown) to complete Layers 9-10. Glue layer 10 to layer 9 to provide a solid base for the bigger counter top. Use the included shims to level the pieces before gluing it down.
8. Place and level the countertops using the provided shims. Once the top is properly levelled, then glue them to the top layer of quarry stone.
9. Allow glue to set properly before using.
Note: Refer to directions printed on the included adhesive for setting times.
stone oasis collection
Vancouver Office, 2104-290 Newport Drive, Port Moody, BC V3H 5N2 T (778) 689 7670 or 1 800 461 2278 F (604) 949 0321 [email protected] Office, 152 Brandt Street, Steinbach, MB R5G 0R2 T (204) 326 3445 or 1 800 461 2278 F (204) 326 5915 [email protected]
Calgary Office, 813 McCool St., Crossfield Alberta, Box 1136, T0M 0S0 T (403) 946 4630 or 1 800 461 2278 F (403) 946 4631 [email protected] Office, 909 Gateway Road, Winnipeg, MB R2K 3L1 T (204) 667 3310 or 1 800 342 2879 F (204) 663 4854 [email protected]
Stone Oasis Circle Patio and Border
Stone Oasis Rectangular Patio and Border
Stone Oasis Pillar
Stone Oasis Grand Waterfall
Stone Oasis Circle Firepit
Stone Oasis Waterfall
Stone Oasis Curved Bar
Stone Oasis Fireplace Wood Storage
for more information please visit our
website:
www.barkmanconcrete.com
Stone Oasis Square Firepit
Stone Oasis Rectangular Patio with Inlay
Stone Oasis Square Waterfall
Stone Oasis Compact Fireplace
Follow barkman on Facebook,
Twitter and visit our YouTube channel.
Stone Oasis Fireplace