obstruction lighting catalog

Lighting At gREAt hEightS FoR 75 YEARS.

o b St R u c t i o n L i g h t i n g

PRODUCT CATALOGHUGHEYAnDPHILLIPS.coM

b ro a d c a s t | te l e c o m m u n i c a t i o n s | Wi n d tu r b i n e s | ta l l S t r u c t u re s | u t i l i t i e s

cAtALog no. 1201

Hughey & Phillips Obstruction Lighting Shines Brighter.

About Hughey & PhillipsFor more than 75 years, hughey & Phillips, LLc products have found their place atop some

of the world’s most monumental architectural achievements. At hughey & Phillips, we make

a complete line of cost-effective obstruction lighting and control solutions that are proven to

be highly efficient and reliable with improved maintainability and a longer operational life.

As either stand-alone fixtures or as part of an integrated system, hughey & Phillips’ low,

medium, and high intensity lighting solutions provide illumination for radio and television

transmission towers, communications and microwave antennas, wind turbines, grain

elevators, buildings, smokestacks, bridges, and other obstructions to aerial navigation as

specified by the FAA, Fcc, icAo, DgAc of Mexico and transport canada.

Advancements in LED-based obstruction lighting technologies have resulted in lighting

fixtures that extend our beacon service life up to 10 times longer than incandescent bulbs

with lower power consumption. Additionally, our strobes use unique parabolic reflectors/

linear strobetubes optics and integrated flashhead blocking strips to minimize ground scatter

light for more community friendly lighting systems.

APPLICATIONSAll low intensity lights are available as single or double lights. the low intensity and medium

intensity lighting are used to mark air traffic obstructions. Different lights are used for different

specific applications, all-round illuminated obstruction lights with a light intensity of 10 cd

(candela) or 32 cd, flashing medium intensity lights in red or white with 2,000 cd or 20,000

cd and even high-intensity lights in white with up to 270,000 cd. in the united States the

use of specific lighting is defined in the FAA Advisory circular 70/7460-1 on the marking of

obstructions. the icAo (international civil Aviation organization) or Local Aviation Authority

governs for national regulations.

VErSATILE OBSTrUCTION LIGHTING SOLUTIONS fOr ANY INdUSTrY.

hughey & Phillips engineers and designs a complete line of low, medium and high intensity

lighting technology solutions that provide illumination for a wide range of industries:

• Broadcast

• Telecommunications

• Wind Turbines

• Tall Structures

• Utilities

Whether you need to illuminate radio, television or communication towers; wind turbines;

buildings; smokestacks; bridges; or other obstructions to aerial navigation, hughey & Phillips

provides innovative lighting technology solutions.

We have a full engineering staff providing complete support and design in optical, electrical

and mechanical disciplines to customize any of our products to fit your application’s unique

needs. to learn more, visit www.hugheyandphillips.com

oRDERing inFoRMAtion

Designed for a wide range of obstruction lighting applications, hughey &

Phillips’ broad line of incandescent, xenon and LED-based lighting fixtures

and control solutions provide long-life operation and highly reliable

performance. contact a hughey & Phillips representative today by visiting

www.hugheyandphillips.com or by calling toll-free 877-285-4466.

• Cost-effective obstruction

lighting and controls solutions

• Highly efficient products

save energy and reduce

maintainability costs

• Stand-alone fixtures or

integrated systems

available for low, medium

and high intensity

lighting products

• Longer operational life keep

structures illuminated and

replacements costs low

hughey & Phillips is a global

leader in the design and

manufacturing of obstruction

lighting technology. the

company offers complete

solutions comprised of power

and lighting systems designed

and manufactured in the uSA.

MEdIUM INTENSITY

HIGH INTENSITY CABLES

INTErNATIONAL PrOdUCTS

PRODUCT OVERVIEWhughey & Phillips obstruction lights have a sturdy construction, are built to last and fulfill both national

and international specifications. All our lights are completely non-corroding, low-maintenance lights.

our product portfolio includes state-of-the-art LED low and medium intensity obstruction lights as well

as lights with a conventional light-source ranging from simple incandescent obstruction lights to high-

intensity strobe lights for special applications.

our power-saving LED lights guarantee a life span that is several times longer than conventionally

equipped lights. this is achieved by a redundant circuit design and reduction of power consumption by

over 90% of the normal usage of incandescent lights. infrared (iR) LED systems are also available.

TOWER & OBSTRUCTIOn LIghTIng gUIDEthe hughey & Phillips tower and obstruction lighting guide provides the latest FAA, Fcc, transport

canada & icAo tower and obstruction products for lighting buildings, towers, smokestacks, grain

elevators or other structures, either temporary or permanent, which might present obstructions to air

navigation. References will be made in this guide to FAA, Fcc, transport canada & icAo requirements.

the specifications and guidelines referred to are the following:

• FAA Advisory Circular No. 150/5345-43

Specification for obstruction Lighting Equipment

• FAA Advisory Circular AC 70/7460-1K

obstruction Marking and Lighting

• FCC Rules and Regulations Part 17

construction, Marking and Lighting of Antenna Structure

• ICAO Aerodromes Annex 14

international Standards and Recommended Practices

• Transport Canada CAR 621.19

• Certified by the Secretary of Communications & Transport of Mexico

copies of these documents are available from the issuing agency or by contacting hughey & Phillips.

All hughey & Phillips products where applicable are qualified to FAA specifications Ac150/5345-43. in

order to maintain an FAA listing, hughey & Phillips must undergo rigid quality review twice yearly by an

independent test laboratory.

MAKING THE WORLD

BRIGHTER.

For over 75 years, hughey &

Phillips obstruction lighting

has earned a reputation for

quality, dependability and

innovation the world over.

in fact, we’ve illuminated

some of the globe’s highest

structures on six continents.

Lighting Up the World’s Towering Achievements .

9 22 26 34LOW INTENSITY 4

ACCESSOrIESLIGHTINGSYSTEMS fAA STANdArdS52 63 76dIAGrAMS 40

LOW INTENSITY

LOW InTEnSITY

6 HUGHEYAnDPHILLIPS.coM

FAA type: L-810 Steady burn obstruction LightHORIZON™

L-810 LED obStRuction Light

APPLICATIONthe hughey & Phillips L-810 obstruction Light provides an LED based solution to the FAA

L-810 style of steady burning lights. the L-810 LED is currently available in both single and

double configurations operating at 120V, 240V, 277VAc and also in a range of 9-48 VDc.

both configurations are available as original equipment or as a direct replacement to the

existing socket/lamp/lens on h&P L-810 incandescent ob2x Series obstruction lights.

fAA Type: L-810 Steady burn obstruction Light

ICAO Type: Low intensity type b obstacle Light

ETL Certified: FAA Ac 150 45-43F

Compliant to: icAo Annex 14, cAR 621.19, MiL-c-7989

fEATUrES:• LED based obstruction lights last over 15 times longer than an incandescent light

• Approximately 94% less power than 116 Watt standard incandescent lamp

• 4 Watt Power Consumption (AC version) / 3.4 Watts (DC Version)

• Available in both side and bottom conduit hubs at ¾” and 1” NPT

• Weather resistant lamp assembly & housing

• Self-contained wiring compartment on double units eliminates additional boxes

• Operates as a steady burn or flashing light

• Resistant to shock and vibration

• Direct replacement for existing incandescent fixtures

• 5 Year Warranty

PHOTOMETrIC SPECIfICATIONS Beam Spread: 360° horizontal, 10° Minimum Vertical

Effective Intensity: > 32 candela

MECHANICAL SPECIfICATIONSBase Material: cast Aluminum with aviation red powder coat

Lens: heat resistant clear glass

Single: 8” x 5.5” x 5.5” (H x W x L), 2 lbs.

double: 8” x 5.5” x 11.5” (H x W x L), 6 lbs.

ENVIrONMENTAL SPECIfICATIONSTemperature: -55°c to +55°c (-67°F to 130°F)

humidity: 95% Relative humidity

Miscellaneous: Will withstand exposure to wind-blown rain

from any direction, salt-laden atmosphere and indspeeds of

240 kph (150 mph).

PARt nuMbER DEScRiPtion

45-1000-001 L-810 LED 95-277VAc SgL bot hub 3/4

45-1001-001 L-810 LED 95-277VAc SgL bot hub 1

45-1002-001 L-810 LED 95-277VAc SgL SiDE hub 3/4

45-1003-001 L-810 LED 95-277VAc SgL SiDE hub 1

45-1004-001 L-810 LED 95-277VAc DbL bot hub 3/4

45-1005-001 L-810 LED 95-277VAc DbL bot hub 1

45-1006-001 L-810 LED 95-277VAc DbL SiDE hub 3/4

45-1007-001 L-810 LED 95-277VAc DbL SiDE hub 1

45-1008-001 L-810 LED 9-48VDc SgL bot hub 3/4

45-1009-001 L-810 LED 9-48VDc SgL bot hub 1

45-1010-001 L-810 LED 9-48VDc SgL SiDE hub 3/4

45-1011-001 L-810 LED 9-48VDc SgL SiDE hub 1

45-1012-001 L-810 LED 9-48VDc DbL bot hub 3/4

45-1013-001 L-810 LED 9-48VDc DbL bot hub 1

45-1014-001 L-810 LED 9-48VDc DbL SiDE hub 3/4

45-1015-001 L-810 LED 9-48VDc DbL SiDE hub 1

SPARE PARtS DEScRiPtion

45-0001-001 L-810 Light MoDuLE 95-277VAc

45-0002-001 L-810 Light MoDuLE 9-48VDc

A6A0008AG NEOPRENE GASKET

B6A0008AA LENS HOLDER w/7” CHAIN

FAA type: L-810 Steady burn obstruction Light

incAnDEScEnt obStRuction LightS

LOW InTEnSITY

APPLICATIONthe ob20 and ob21 single obstruction lights are equipped with a screw base lamp

receptacle. the fixtures are cast aluminum and utilize flange type red fresnel lenses. the

fixtures are available with either bottom entrance (OB20) or side entrance (OB21) for 3/4” or

1” conduit fittings. The fixtures are suitable for use with 120 or 230 VAC lamps.

Certified to: FAA Ac 150/5345-43F

Compliant to: transport canada cAR 621.19

icAo Annex 14

uSAF AFMAn 32-1076

MoDELS

OB20A31 3/4” bottom conduit entrance

OB20A41 1” bottom conduit entrance

OB21A31 3/4” side conduit entrance

OB21A41 1” side conduit entrance

7877.285.4466 toLL FREE

PHOTOMETrIC SPECIfICATIONSBeam Spread: 360° horizontal, 10° Minimum Vertical

Effective Intensity: >32 candela

MECHANICAL SPECIfICATIONSBase Material: cast aluminum with aviation red powder coat

Lens: heat resistant glass, red.

SINGLE OBSTrUCTION LIGHTDimensions: 230mm h x 140mm W x 140mm L

(9”H x 5.5”W x 5.5”L)

Weight: 1.8 Kg (4 Pounds)





240 kph (150 mph).

SPARE PARtS AnD AccESSoRiES

Lh116120gE Lamp 120 VAc, 116 Watts

FL02b02810 Red Fresnel Lens

XLcb4S200 Lamp Receptacle

A6A0008Ag neoprene gasket

Lh116230 Dt Lamp 120 VAc, 116 Watts

B6A0008AA Lens Holder w/7” Chain

LOW InTEnSITY


FAA type: L-810 Steady burn obstruction Light

DoubLE incAnDEScEnt obStRuction LightS

APPLICATIONthe ob22 and ob24 double obstruction lights are equipped with two screw base lamp

receptacles. the fixtures are cast aluminum and utilize flange type red fresnel lenses. the

fixtures are available with either side entrance or bottom entrance for 3/4” or 1” conduit

fittings. the fixtures are suitable for use with 120 and 230 VAc lamps.

MoDELS

OB22A31 3/4” bottom conduit entrance

OB22A41 1” bottom conduit entrance

OB24A31 3/4” side conduit entrance

OB24A41 1” side conduit entrance

DOUBLE OBSTRUCTIOn LIghTS WITh AUTOMATIC TRAnSfER RELAYin many circumstances it is highly desirable, or required, to employ a lamp transfer relay

with a double obstruction light. upon failure of the first lamp, the relay will transfer power

to the second, or standby lamp. the relay is mounted within the fixture base. this relay

is of the single pole, single throw, normally closed type. only one lamp in the double

obstruction light is energized when a transfer relay is used. the fixtures are suitable for use

with 120 and 230 VAc lamps.

MoDELS

OB22A41TM1 3/4” or 1” bottom conduit entrance

OB24A41TM1 3/4” or 1” side conduit entrance

PHOTOMETrIC SPECIfICATIONSBeam Spread: 360° horizontal, 3° Minimum Vertical

Effective Intensity: > 32 candela

MECHANICAL SPECIfICATIONSBase Material: cast aluminum with aviation orange,

powdercoat paint finish

Lens: heat resistant glass, red

dOUBLE OBSTrUCTION LIGHTDimensions: 235mm h x 140mm W x 292mm L

(9.25”H x 5.5”W x 11.5”L)

Weight: 3.75 Kg (8.25 Pounds)




from any direction, salt-laden atmosphere and windspeeds

of 240 kph (150 mph)

SPARE PARtS AnD AccESSoRiES

Lh116120gE Lamp 120 VAc, 116 Watts

FL02b02810 Red Fresnel Lens

XLcb4S200 Lamp Receptacle

A6A0008Ag neoprene gasket

Lh116230 Dt Lamp 120 VAc, 116 Watts

6A0013SK3 Transfer Relay Assembly

B6A0008AA Lens Holder w/7” Chain

MEdIUM INTENSITY

FAA type: L-864, L-865, and L-866 Medium intensity LightingHORIZON™ SERiES

LEd STrOBE SYSTEM dESCrIPTIONthe horizon™ Dual Medium intensity LED Strobe System provides daytime white and

nighttime red lights in one unit. its self-contained power supply, with available gPS sync and

day/night sensor, simplifies wiring but also accepts external signals if desired. Advanced

features include advanced LED modules, cutting edge optics, individual LED monitoring/

bypass, and active lightning protection (patent pending). the unit also monitors the system

and provides a no or nc alarm contact upon any system failure.

APPLICATIONMedium intensity obstruction lighting systems are typically used on structures between 150’

(45m) and 500’ (150m) above ground level to provide aviation safety. the use of a medium

intensity white strobe during the daytime typically eliminates the need to paint the structure

with aviation orange and white stripes. the use of a red flashing beacon at night provides

a “community friendly” light. Hughey & Phillips medium intensity obstruction lights are

designed for lighting tall structures such as communication, television and radio towers, wind

turbines, smokestacks, cooling towers, tall buildings, catenary river crossings and bridges.

fAA Type: L864, L865 or L-864/865 Medium intensity Lighting

ICAO Type: type A/b Medium intensity obstacle Light

ETL Certified: FAA Advisory circular 150/5345-43

Compliant for use with: icAo Annex 14, MiL-c-7989

DgAc of Mexico, cAR 621.19


MEdIUM INTENSITY

PHOTOMETrIC SPECIfICATIONSDay Mode (White): 20,000 candela ± 25%

night Mode (White or Red): 2,000 candela ± 25%

Beam Spread: 3° minimum

horizontal Coverage: 360°, omni-directional

flash Rate: 40 FPM Day & White night

24 FPM night Red




from any direction, salt-laden atmosphere and windspeeds of

240 kph (150 mph)

MECHANICALWeight, flashhead: 8 kg (17 lbs)

flashhead Lens Material: high temp/uV Resistant Acrylic

ELECTrICALInput Voltages: 120, 230/240, 277, 480 VAc

Input frequencies: 50 or 60 hz

Power Consumption, Day: 25 Watts

Power Consumption, night: 15 Watts

FAA type: L-864, L-865, and L-866 Medium intensity LightingHORIZON™ SERiES

FEAtuRES bEnEFitS

original Equipment Manufacturer Designed, engineered and manufactured by hughey & Phillips

one source for fixtures and complete lighting systems

Single Flashhead construction compact design for dual (red/white) operation

Failsafe Redundancy Automatic switching for nighttime redundancy of dual systems

gPS Synchronization Available built in gPS SYnc module

iR capability Available Viewable with nVg goggles

Wiring compatibility Existing wiring can be used for retrofit applications

Environmentally sealed connector

Fewest number of control wiring on the market

interchangeable LED Modules Single screw access

built-in Safety interlock switch

Fully field serviceable unit

cutting Edge optics design h&P exclusively designed ‘Eklipse’ optics package

community friendly lighting system

Lightest Flashhead 17 lbs

Ease of handling and installation

universal input operating voltage of 95-277 VAc, 50/60hz

dIMENSIONS

MEdIUM INTENSITY

11877.285.4466 toLL FREE


50-0002-001 FAA type L-864, 95-277VAc 50/60hz

50-0003-001 FAA type L-865, 95-277VAc 50/60hz

50-0004-001 FAA type L-866, 95-277VAc, 50/60hz

50-0005-001 FAA type L-864/865, 95-277VAc 50/60hz

these specifications are subject to change.

FAA type: L-864 Medium intensity Lighting

MODEL KG 114 300 mm BeaconFoR AiRPoRt AnD obStRuction Lighting

MEdIUM INTENSITY

APPLICATIONModel KG 114 300mm Beacon is approved as a marker light for obstructions to air

navigation such as television, radio, microwave and transmission line towers, bridges,

water tanks, stacks and other tall structures as specified by the FAA. Model KG 114 300mm

beacon is in full compliance with FAA beacon requirements for marking of obstructions to

air navigation.

Meets icAo Requirements & transport canada

fEATUrESConstructed of heavy aluminum casting, Model KG 114 300mm Beacon is completely

weatherproof, and features:

• Concave base: with drain port at lowest point prevents accumulation of moisture from

condensation.

• Hinged center frame: hinged at the center between the upper and lower lens assemblies

to provide ready access for inspection and lamp replacement. the hinge rings, neoprene

gasket, butterfly locking clamp, maintain a weatherproof center seal.

• Color filter supports: with flexible fins provide heat insulation and cushioning, thus

eliminating color filter breakage from expansion and construction.

• Equipped with stainless hardware.

• IR compatible with enhanced flight vision systems that use IR energy emissions for

imaging, including nVg goggles.


PARt no. DEScRiPtion FAA DESignAtion WEight

KG 114 F0001 300mm Beacon with Red Lens L864 73 lbs

Lh620120gE 620 Watts, 120 V Lamp

Lh700230hDt 700 Watts, 230 V Lamp

MEdIUM INTENSITY

dESCrIPTIVE dATAModel KG 114 300mm Beacon is designed for service under all climatic conditions. Frame

and hardware are constructed of non-ferrous materials. All the glassware is heat-resistant

meeting FAA and Military Specifications.

the optical System consists of four red, heat-resistant lenses, designed to provide a definite

beam through 360o horizontally. the two lamp receptacles are mounted to properly position

the two 620 or 700 watt Mogul Pre-focus beacon lamps, thus providing correct beam

distribution in accordance with FAA and Military specifications.

A three terminal connecting block is mounted in the base allowing each lamp to be

independently fed and monitored. internal wiring is heat-resistant insulated flexible wire,

terminates at the connecting block. unless otherwise ordered, beacons are furnished with

five feet of #12-3 Conductor Neoprene Cable, entering the base through a 1” Watertight

connector. conduit may be used by removing the Watertight connector and disconnecting

the External cable.

neoprene gaskets are designed for long life under extreme temperatures. upper gasket

Retainer, and Lower gasket Retainer assure Weatherproof protection between lenses.


MODEL KG 114 300 mm BeaconFoR AiRPoRt AnD obStRuction Lighting

13877.285.4466 toLL FREE

FAA type: L-865 and L-866 Medium intensity Lighting

Flashguard® 2000

MEdIUM INTENSITY


ELEctRicAL SPEciFicAtionS

Ac input Power 120 VAc +/- 10%, 60 hz, 1 phase standard; 195 watts day operation, 60 watts night operation

Dc input Power 24 VDc +/- 10%;120 watts day operation, 45 watts night operation

Power options 240, 480 VAc +/- 10%; 60 hz or 240, 480 VAc +/- 10%, 50 hz

transient transient protection is provided by:Protection • Company proprietary circuits which incorporate series resistors and zener diodes on all signal lines

• 5 kilovolt rated transformer, primary and secondary line to ground insulation

• Rectifier diode network protection by varistors

System Status two neon lamps and four LEDs indicate system andindicators subsystem operating status.

Safety the flashhead and power supply are both equipped with interlocks so that opening either unit interrupts the capacitor charging circuit and discharges the high voltage energy storage capacitors in the power supply to less than 50 volts within 30 seconds.

EnViRonMEntAL SPEciFicAtionS

temperature -67°F (-55°c) to + 130°F (+55°c) per MiL-StD-810

humidity 95% relative humidity per MiL-StD-810

Wind Wind speeds up to 150 mph (67 m/sec)

Wind Loading 72 lbs (32 kg) at 150 mpg (67 m/sec) Surface area is 1.282 (0.12m2)

Wind blown Exposure to wind blown rain from any direction per MiL-StD-810Rain

Salt Fog Exposure to salt-laden atmosphere per MiL-StD-810

oPticAL PERFoRMAncE SPEciFicAtionS bEAM SPREAD1 PEAK FLASH (degrees) intEnSitY2 FLASh/RAtE DuRAtion3

MoDE horizontal Vertical (candelas) (flashes/minute) (milliseconds)

Day/twilight 360° 3° min 15,000 min 40-L-865 <10 25,000 max 60-L-866

night 360° 3° min 1,500 min 40 for L-865 100 to 250 2,500 max 60 for L-866

notes: 1. the lower edge of the vertical beam spread lies between –1.5° and -0.5° with respect to the horizon. 2. Flashlamp light out meets the FAA minimum requirements of 15,000 candelas day/twilight and 1,500 candelas night for a period of not less than one year. 3. When the effective flash duration is generated with a group of short flashes, the flash rate is not less than 30 per second.

fLASHGUArd® 2000 SYSTEM dESCrIPTIONthe Flashguard 2000 Medium intensity White Lighting System combines a daytime white

strobe light and a nighttime white flashing light into a single flashhead. the system is also

available as a red flashhead which can be used at night in place of red incandescent lighting,

for much longer light source life. the flashhead is powered and controlled by a power supply

that can be mounted remotely at the base of the structure. the power supply constantly

monitors the operation of the system, and provides alarm contact closure upon any failure.

the system automatically switches between day, twilight, and night intensities by the use of

a calibrated photocell. Flashguard® 2000 flashheads incorporate a light blocking strip that

minimizes ground scatter light, resulting in a community friendly lighting system.


(45M) and 500’ (150M) above ground level to provide aviation safety. the use of a medium


with aviation orange and white stripes. the use of a white flashing strobe at night provides an

‘eye catching’ light for low flying aviators. hughey & Phillips’ medium intensity obstruction

lights are designed for lighting tall structures such as communication, television and radio

towers, chimneys, cooling towers, tall buildings, catenary river crossings and bridges. this

light is compatible with Enhanced Flight Vision Systems that use iR energy emissions for


fAA Type: L-864, L-865 & L-866 Medium intensity Lighting

ICAO Type: Medium intensity obstacle Light

Applicable Specifications:

Conforms to: FAA Advisory circular Ac 70/7460-1

FAA Advisory circular Ac 150/5345-43E | icAo Annex 14

transport canada tP 382E | DgAc of Mexico 150/5345-43E

18.50 (470)

16.19 (411)

16.26(412)

17.25(438)

6.00(152)

3.50(89)

0.44 (11) Mounting hoLE4 PLAcES

WEight: 53 PounDS (24 KILOGRAMS)

3/4” CABLE CONNECTOR

SS-120 PhotocontRoL iSREMoVAbLE FoR inDooR inStALLAtion

3.38(86)

5.00(127)

SS 120 PhotocontRoL

W/REcEPtAcLE 5.00(127)

8.63(219)

10.50 (267)15.50 (394)cLEARAncE

MEdIUM INTENSITY

MECHANICAL dIMENSIONS

SS-175 PoWER SuPPLY

5.00 (127)cLEARAncE

15.92 (404)FLAShhEAD gLobE LiFtS FoR AccESS

to FLAShtubES

FocAL PLAnE

3/4” CABLEconnEctoR

16.50 (419)

15.00 (381)WEight: 22 PounDS

(10 KILOGRAMS)

4.80(122)

3.88(98)

120o

90o

90o

90o

120o

Mounting SLot0.69 X 0.81

(17 X 21)6 PLAcES on

13.25 (337)boLt ciRcLE

bottoM oF FLAShhEADFoR Mounting With

3 oR 4 FAStEnERS

SS-176 FLAShhEAD


Flashguard® 2000

15877.285.4466 toLL FREE

DiMEnSionS ARE in inchES (MiLLiMEtERS)

fLASHGUArd® 2000B SYSTEM dESCrIPTIONthe Flashguard 2000b Medium intensity White Lighting System combines a daytime white

strobe light and a nighttime white flashing light into a single flashhead. the system is also

available as a red flashhead which can be used at night in place of red incandescent lighting,

for much longer light source life. the flashhead is powered and controlled by a power supply

that can be mounted remotely at the base of the structure. the power supply constantly

monitors the operation of the system, and provides alarm contact closure upon any failure.

the system automatically switches between day, twilight, and night intensities by the use of

a calibrated photocell. Flashguard® 2000b flashheads incorporate a light blocking strip that

minimizes ground scatter light, resulting in a community friendly lighting system.


(45M) and 500’ (150M) above ground level to provide aviation safety. the use of a medium


with aviation orange and white stripes. the use of a white flashing strobe at night provides an

‘eye catching’ light for low flying aviators. hughey & Phillips’ medium intensity obstruction

lights are designed for lighting tall structures such as communication, television and radio

towers, chimneys, cooling towers, tall buildings, catenary river crossings and bridges. this

light is compatible with Enhanced Flight Vision Systems that use iR energy emissions for


fAA Type: L-864 (Red) or L-865 (White) Medium intensity Lighting

ICAO Type: Medium intensity obstacle Light

Applicable Specifications:

Conforms to: FAA Advisory circular Ac 70/7460-1

FAA Advisory circular Ac 150/5345-43 | icAo Annex 14

transport canada tP 382E | DgAc of Mexico 150/5345-43F






ground Scatter: <3% Light output at -10° Vertical

flash Rate: 40 FPM Day & White night

ENVIrONMENTALTemperature: -55° to +55° c (-67° F to +130° F)

Will withstand exposure to: 95% relative humidity,

wind-blown rain-direction, salt-laden atmosphere,

Wind Speed - 240kph (150mph)


Weight, Power Supply: 24 kg (53 lbs)

Power Supply Enclosure: 304 Stainless Steel - standard.

316L Stainless Steel - optional


Stainless Steel - optional 316L

ELECTrICALInput Voltages: 120, 230/240, 277, 480 VAc




Power Consumption, Backup: 77 Watts

Peak Inrush Current: 7A @ 120VAc

Available Alarm Contacts (form C dry-contact): Power Failure,

Mode Status, Strobe Failure, Sidelight #1 Fail, Sidelight #2 Fail

White Fg2000b

Red Fg2009b

MEdIUM INTENSITY

FAA type: L-864, L-865, or L-866 Medium intensity Lighting

Flashguard® 2000b

SYSTEM fEATUrES:• Single flashhead provides white or red medium intensity

operation with no moving parts

• Precise optics minimize ground scatter light

• Alarm contacts provided for connection to any monitoring

system

• Rugged design of flashhead and power supply is suitable for

outdoor installation in any climate

fLASHHEAd fEATUrES:• Internally triggered Xenon strobe tubes utilized for long-life and

maximum efficiency, without creating corrosive ozone

• Parabolic reflector optics and linear strobe tube optics

combination provides very precise optics and blocks ground

scatter light in both red or white operation

• Lens raises and locks in place, providing easy access to strobe

tubes

• Only three components used in flashhead - minimal

maintenance required at top of structure

• Safety interlock switch included

• No moving parts

• High temperature, UV resistant acrylic flashhead lens

POWER SUPPLY fEATURES:• Provides power electronics, timing circuitry, and monitoring for

lighting system

• Automatic day/night intensity control

• Manual intensity override

• Easily accessible components

• Plug-in-play circuit cards

• Control and monitoring for up two sidelight levels with four

steady burning obstruction lights

• Fail-safe monitoring system with up to five remote alarm

contacts

• Stainless steel NEMA 4X enclosure

• Low power consumption

MEdIUM INTENSITY

FAA type: L-864, L-865, or L-866 Medium intensity Lighting

Flashguard® 2000b

17877.285.4466 toLL FREE


Flashguard® 3000

MEdIUM INTENSITY


ELEctRicAL SPEciFicAtionS

Ac input Power 120 VAc +/- 10%, 60 hz, 1 phase standard; 195 watts day operation, 60 watts alternate white night operation

Dc input Power 24 VDc +/- 10%;120 watts day and red night operation, 45 watts alternate white night operation

Power options 240, 480 VAc +/- 10%; 60 hz or 240, 480 VAc +/- 10%, 50 hz

transient transient protection is provided by:Protection • Circuits which incorporate series resistors and zener diodes on all signal lines

• 5 kilovolt rated transformer, primary and secondary line to ground insulation

• Rectifier diode network protection by varistors

System Status two neon lamps and four LEDs indicate system andindicators subsystem operating status.

System test Manual override switches for remote day and night operation testing.controls Push button operation for testing fault circuit operation.

Safety the flashhead and power supply are both equipped with interlocks so that opening either unit interrupts the capacitor charging circuit and discharges the high voltage energy storage capacitors in the power supply to less than 50 volts within 30 seconds.

EnViRonMEntAL SPEciFicAtionS

temperature -67°F (-55°c) to + 130°F (+55°c) per MiL-StD-810

humidity 95% relative humidity per MiL-StD-810

Wind Wind speeds up to 150 mph (67 m/sec)

Wind Loading 105 lbs (32 kg) at 150 mpg (240 kph). Surface area is 1.98 ft2

Wind blown Exposure to wind blown rain from any direction per MiL-StD-810Rain

Salt Fog Exposure to salt-laden atmosphere per MiL-StD-810

oPticAL PERFoRMAncE SPEciFicAtionS bEAM SPREAD1 PEAK FLASH (degrees) intEnSitY2 FLASh/RAtE DuRAtion3

MoDE horizontal Vertical (candelas) (flashes/minute) (milliseconds)

Day/twilight 360° 3° min 15,000 min 40-L-865 <10 25,000 max

night Red 360° 3° min 1,500 min 20-40 for L-864 750 2,500 max

White night- 360° 3° min 1,500 min 40 for L-865 100 to 250 backup 2,500 max

notes: 1. the lower edge of the vertical beam spread lies between –1.5° and -0.5° with respect to the horizon. 2. Flashlamp light out meets the FAA minimum requirements of 15,000 candelas day/twilight and 1,500 candelas night for a period of not less than one year. 3. When the effective flash duration is generated with a group of short flashes, the flash rate is not less than 30 per second.

fLASHGUArd® 3000 SYSTEM dESCrIPTIONthe Flashguard 3000 Medium intensity Dual Lighting System combines a daytime white

strobe light and a nighttime red flashing strobe into a single flashhead, eliminating the

need for two separate lighting systems. the flashhead is powered and controlled by a

power supply that can be mounted remotely at the base of the structure. the power supply

constantly monitors the operation of the system, and provides alarm contact closure upon

any failure. the system automatically switches between day and night intensities by the use

of a calibrated photocell. Flashguard® 3000 flashheads incorporate a light blocking strip that

minimizes ground scatter light, resulting in a “community friendly” lighting system.

APPLICATIONMedium intensity obstruction lighting systems are typically used on structures between

150’(45M) and 500’ (150M) above ground level to provide aviation safety. the use of a

medium intensity white strobe during the daytime typically eliminates the need to paint the

structure with aviation orange and white stripes. the use of a red flashing beacon at night

provides a “community friendly” light. Hughey & Phillips’ medium intensity obstruction lights

are designed for lighting tall structures such as communication, television and radio towers,

chimneys, cooling towers, tall buildings, catenary river crossings and bridges. this light is

compatible with Enhanced Flight Vision Systems that use iR energy emissions for imaging,

including nVg goggles.

fAA Type: L-864/865 Medium intensity Lighting


ETL Certified: FAA Advisory circular 150/5345-43E



MEdIUM INTENSITY

18.50 (470)

16.19 (411)

16.26(412)

17.25(438)

6.00(152)

3.50(89)

0.44 (11) Mounting hoLE4 PLAcES

WEight: 53 PounDS (24 KILOGRAMS)

3/4” CABLE CONNECTOR

SS-120 PhotocontRoL iSREMoVAbLE FoR inDooR inStALLAtion

3.38(86)

5.00(127)

SS 120 PhotocontRoL

W/REcEPtAcLE 5.00(127)

8.63(219)

10.50 (267)15.50 (394)cLEARAncE

MECHANICAL dIMENSIONS

SS-177 PoWER SuPPLY

SS-178 FLAShhEAD


Flashguard® 3000

19877.285.4466 toLL FREE


Flashguard® 3000b

fLASHGUArd® 3000B SYSTEM dESCrIPTIONthe Flashguard® 3000b Medium intensity Dual Lighting System combines a daytime

white strobe light and a nighttime red flashing strobe into a single flashhead, eliminating

the need for two separate lighting systems. the flashhead is powered and controlled by a

power supply that can be mounted remotely at the base of the structure. the power supply

constantly monitors the operation of the system, and provides alarm contact closure upon any

failure. the system automatically switches between day and night intensities by the use of a

calibrated photocell. Flashguard® 3000b flashheads incorporate a light blocking strip that

minimizes ground scatter light, resulting in a “community friendly” lighting system.

APPLICATIONMedium intensity obstruction lighting systems are typically used on structures between

150’(45M) and 500’ (150M) above ground level to provide aviation safety. the use of a

medium intensity white strobe during the daytime typically eliminates the need to paint the

structure with aviation orange and white stripes. the use of a red flashing beacon at night

provides a “community friendly” light. Hughey & Phillips’ medium intensity obstruction lights

are designed for lighting tall structures such as communication, television and radio towers,

chimneys, cooling towers, tall buildings, catenary river crossings and bridges. this light is

compatible with Enhanced Flight Vision Systems that use iR energy emissions for imaging,

including nVg goggles.

fAA Type: L-864/865 Medium intensity Lighting


ETL Certified: FAA Advisory circular 150/5345-43F








ground Scatter: <3% Light output at -10° Vertical

flash Rate: 40 FPM Day & White night, 24 FPM Red night





240 kph (150 mph).


Weight, Power Supply: 32 kg (70 lbs)

Power Supply Enclosure: 304 Stainless Steel - standard.

316L Stainless Steel - optional


ELECTrICALInput Voltages: 120, 230/240, 277, 480 VAc, 24VDc




Power Consumption, Backup: 77 Watts

Peak Inrush Current: 7A @ 120VAc

Available Alarm Contacts (form C dry-contact): Power Failure,

Mode Status, Strobe Failure, Sidelight #1 Fail, Sidelight #2 Fail

MEdIUM INTENSITY


Flashguard® 3000b

SYSTEM fEATUrES:• Single flashhead provides white or red medium intensity

operation with no moving parts

• Dual flashtubes and dual trigger transformers provide night

time redundancy - no single point of failure in the flashhead

• Precise optics minimize ground scatter light

• Alarm contacts provided for connection to any monitoring

system

• Rugged design of flashhead and power supply is suitable for

outdoor installation in any climate

fLASHHEAd fEATUrES:• Upper optics provides red flashing beacon lighting

• Lower optics provides medium intensity white strobe lighting

• Identical strobe tube for red and white eliminates extra spare

parts

• Internally triggered Xenon strobe tubes utilized for long-life and

maximum efficiency, without creating corrosive ozone

• Parabolic reflector optics and linear strobe tube optics

combination provides very precise optics and blocks ground

scatter light in both red or white operation

• Lens raises and locks in place, providing easy access to strobe

tubes

• Only five components used in flashhead - minimal maintenance

required at top of structure

• Dual flashtubes and trigger transformers provide night time

redundancy

• Safety interlock switch included

• No moving parts

• High temperature, UV resistant acrylic flashhead lens

POWER SUPPLY fEATURES:• Provides power electronics, timing circuitry, and monitoring for

lighting system

• Automatic day/night intensity control


• Easily accessible components


• Control and monitoring for up two sidelight levels with four

steady burning obstruction lights

• Fail-safe monitoring system with up to five remote alarm

contacts



MEdIUM INTENSITY

21877.285.4466 toLL FREE

HIGH INTENSITY

FAA type: L-865 and L-857

Strobeguard® SS-122/125

HIGH INTENSITY

SS-125 OBSTRUCTIOn STROBE LIghTthe Strobeguard® SS-125 is a single enclosure obstruction light designed to meet or

exceed the requirements of Advisory circular 150/5345-43. the enclosures are fabricated

from 304L stainless steel. All plug-in printed circuit boards are protected with a coating

which meets the physical and electrical requirements of MiL-i-46058b. the SS-125 is

supplied with a lightning arrestor capable of withstanding repeated 10,000 ampere current

surges. operated with the SS-122 controller, the system is completely self-activating for

monitoring and identifying any malfunctioning light and is equipped to initiate a remote

alarm. the number of SS-125 obstruction lights used on an installation depends upon the

type of obstruction and its height.

fAA Type: L-856 high intensity Lighting

ICAO Type: type A high intensity obstacle Light

ETL Certified: FAA Advisory circular Ac 150/5345-43

Compliant for use with: icAo Annex 14, canadian Aviation Regulation 621.19

icAo Annex 14, MiL-c-7989, DgAc of Mexico


PHOTOMETrIC SPECIfICATIONSDay 270,000 candela ± 25%

Twilight 20,000 candela ± 25%

Night 2,000 candela ± 25%

Beam Spread 3° Vertical minimum

horizontal Coverage 120° coverage

Cut off Angle <3% light output at -10° Vertical

flash Rate 40 Flashes per Minute (FPM)

ENVIrONMENTALTemperature -55° c to +55° c, -67° F to + 130° F

humidity 95% relative humidity

Will withstand exposure to: Wind-blown rain from any angle

Salt-laden atmosphere, Wind speed of 240kph (150mph)

MECHANICAL

Weight, Controller 11kg (24 lbs)

Dimensions, Controller 14” H x 12” W x 6” D

Weight, flashhead 37kg (82 lbs)

Dimensions, flashhead 14.4” H x 16.2” W x 12.75” D

Enclosure Rating 304 Stainless Steel, nEMA 4X

ELECTrICALInput Voltages 120, 208, 240, 277, 380, 480V

Input frequency 50 or 60 hz

Power Consumption 0.55kVA per flashhead

FAA type: L-865 and L-857

Strobeguard® SS-122/125

HIGH INTENSITY

SS-122 COnTROLLER:Strobeguard® controllers contain the flash interval and timing circuits, intensity selection

controls, and monitoring receivers with status indicators required to operate the SS-125

strobe light. the controller is of modular construction with solid state circuitry for long

life and ease of maintenance. Strobeguard® controllers are designed to operate up to

32 obstruction lights at distances up to 4700 feet. Each controller is equipped with the

necessary manually operated controls to test all modes of operation. Digital monitor lamps

are provided and illuminate when a flashhead or power supply is not operating as required.

Each monitor lamp is operated in a coded mode indicating the location of the flashhead/

power supply which is malfunctioning.

SS-124 AMBIEnT SEnSOR:the SS-124 Light Sensor continuously monitors the ambient lighting conditions and inputs to

the Strobeguard controller the necessary information to automatically control the switching

of daytime, twilight and nighttime modes of operation. the SS-124 is easy to install with the

built-in mounting holes.

STrOBEGUArd® CONTrOLStrobeguard® controls contain the flash interval and timing circuits, intensity selection

controls and monitoring circuitry with status indicators. the Strobeguard® control system

is designed to operate up to 24 flashheads at a distance of up to 2500 feet (760 M), using

a noise-resistant communications format. Each control is equipped with the necessary

manually operated controls to test all modes of operation. bi-color green/red LEDs are

provided to indicate proper operation or fault of each flashhead.

fEATUrES:• Fail-safe monitoring system

• Parabolic Optics minimize ‘ground

scatter’ light: <3% of peak intensity

at -100

• Two-wire cable for sync, mode and

monitoring

• Safety interlocks in each flashhead

• Long-life internally triggered strobe tubes

• Automatic three-level intensity control


• Easily accessible replaceable components


• Remote alarm contacts


• Vertical level indicator and

adjustment system


• Minimal wind loading and weight

• IR Compatible with NVG goggles

25877.285.4466 toLL FREE

INTErNATIONAL


APPLICATIONthe LED-lamp was designed to substitute the current 100/116W incandescent lamp in low

intensity obstacle lights type Rto and otL for the 10cd requirement Low intensity obstacle

Lights type A, acc. to icAo Annex 14, table 6-3, issue July 2004.

in combination with a clear lens the Rto obstacle light with LED-Lamp E27 Rto meets

icAo Low intensity obstacle Light type b (32 cd) – requirement.

rEGULATIONSicAo annex 14, table 6-3, issue July 2004

cE – regulations

CHArACTErISTICS• Compact and robust design

• Replacement for E27 incandescent lamp

• Can be substituted into existing obstacle lights

• Long life expectancy

• Build-in redundancy by redundant connection of LEDs

• Power consumption approx. 4W

• Wide voltage and frequency range

TECHNICAL dATA• Structure: LED-Lamp as replacement for incandescent lamp

• Number of LEDs 6

• Color red

• Chromaticity acc. To ICAO, annex 14, appendix 1, fig. A1-1

• Lamp base E27

• Voltage 100V – 230V AC, 50/60 Hz

• Power consumption approx. 4 Watt

• Temperature range -40OC - + 55OC


65 873 070 LED Lamp E27 Rto, 32 cd

65 975 584 LED Lamp E27 otL, 10 cd


DIMEnSIOnS, WEIghT, PACkIng DATALED Lamp E 27 RTO

• Dimensions: approx. 78.0 x 73.0 mm (h x 0)

• Weight: approx. 0.310 kg

LED Lamp E 27 OTL

• Dimensions: approx. 84.0 x 73.0 mm (h x 0)

• Weight: approx. 0.310 kg

• Packing unit: 4 pieces

• Box dimensions: approx. 165 x 165 x 110 mm (l x w x h)

FoR LoW intEnSitY obStRuction LightS

LED LAMP E27 Rto / otL


FoR LoW intEnSitY obStRuction LightS

LED LAMP E27 Rto / otL

29877.285.4466 toLL FREE


APPLICATIONnight marking for wind turbines according to the national regulation for marking

obstructions to air traffic “Richtlinie zur Kennzeichnung von Luftfahrthindernissen” issued

by the German Federal Ministry of Transport, Building and Housing. Type “W Red”

fUNCTIONA pair of the flashing red obstruction lights LED170 are specified for the night marking of

wind turbines higher than 100m. the timing of the LED170 flashing identifies the marked

obstruction as wind turbine to the pilots of aircrafts. the system automatically switches on

by the use of a calibrated photocell. in order to allow synchronization of the flashing of the

LED170 lights with those on other wind turbines, the LED170 is optionally synchronized by

the use of gPS. the pair of LED170 lights per wind turbine in conjunction with a separate

uninterrupted power supply plus control electronics forms the flashing light system

designed for an individual wind turbine. the LED170 light is maintenance free.

CHArACTErISTICS• Maintenance free obstruction light using high-lumen LEDs

• High lifetime by optimized heat dissipation and low operating current of the LEDs

• Constant light output by compensation of temperature changes

• Rugged housing with self-cleaning transparent cover

• Mechanical interface identical to that of the FG2000/3000B light family

• Fault detection

national regulation for marking aeronautical obstacles, part A and b

TECHNICAL dATA• Power Supply system – 690 or 230V, 50Hz

• Power Consumption system – Approx. 400VA at start of charge

• Mechanical dimensions – 381 x 405 mm (L x H)

• Weight – 8.5 kg

• Flashhead Power Consumption – 22 Watts

• Light Sources – High performance LEDs

• Light Intensity – >170cd

• Horizontal beam spread – 360°

• Vertical beam spread – Min 170cd ±5° Min 34cd ±10° Min 3,4cd ±15°

• Timing of flashing: 1s on - 0.5s off - 1s on - 1.5s off


65 874 240 LED170W 230V, 50hz

65 874 616 LED170W 690V, 50hz

65 874 617 LED170W 230V, 50hz, with gPS

65 874 618 LED170W 690V, 50hz, with gPS


obStAcLE Lighting FoR WinD tuRbinES

LED 170W

obStAcLE Lighting FoR WinD tuRbinES

LED 170W


31877.285.4466 toLL FREE


LED 2000

APPLICATIONthe flashing red omni-directional medium intensity obstacle light LED 2000 is applied to

mark obstacles.

the LED 2000 is in compliance with icAo, July 2004. Annex 14, Volume 1, table 6-3, for

Medium intensity obstacles Lights type b and c.

Steady burning operation at type c is alternatively possible.

fAA Type: L-864, Ac150/5345-43F

ICAO Type: Annex 14, tables 6-3, July 2004

NATO: Stanag 3316

CE-Mark

CHArACTErISTICS• LED-Medium Intensity Obstacle Light 2,000cd

• Extremely low light emittance downwards

Light intensity at -1o

Max. 1,125cd

Min. 750cd

• Effective thermal management

• Steady burning operation as Type C light, up to max. environmental temperature of +55oc

• Very high lifetime

• Redundant circuitry for LEDs


TECHNICAL dATAConstruction: LED - obstacle Light

number of LED: 28

Color of light: Red

Chromaticity: according to icAo, Annex 14, Volume 1, Figure A 1-1

Photometry: according to icAo, Annex 14, Volume 1, table 6-3

Medium intensity obstacle Light 2000cd type b,c

Main voltage: 230 V Ac + 10%, -15%, 50/60 hz

Power consumption: 80 Watt in steady burning operation

40 Watt in blinking mode

Temperature range: -40oc -+ 55oc

PARt no.

65 875 918 LED 2000

DIMEnSIOnS, WEIghT, PACkIng DATADimensions: 335 x 410 mm (h x o)

Weight: appr. 9 kg

Packing unit: 1 piece

Packing size: appr. 600 x 500 x 600 mm (L x W x h)

LED 2000



LED 2000

33877.285.4466 toLL FREE


fig 1: LED 2000 horizontal lightdistribution in beam centre

according to ICAO

fig 2: LED 2000 horizontal lightdistribution at -1O down (-1O Cutoff

condition according to ICAO)

fig 3: LED 2000 vertical lightdistribution according to ICAO

CABLES

77-2992 cable


ASSEMBLYCabling - core-minimum filler to keep as flexible as practical

outer Layer - 7 wires, items 4-10 (4 #14 + 3 #16 AWg)

Cabled around the core with a 7” left hand lay

Binder - 0.002” mylar tape - 25% minimum overlap

Tape shield - 0.002” aluminum mylar tape - 25% minimum overlap

Drain wire - item 11 is pulled under the shield

Jacket - 0.025 polythlyne - color: black

Overall diameter - Ø.600 MAX

SPECIfICATIONS• Temperature rating –55°c to +80°c

• Voltage rating 600 VRMS (conductors 2500 VRMS for electronic use)

• Insulated conductors uL1015 cSA tRE2 iPcEA S–61–402

• Cable uL2653 cSA tR32 iPcEA S–61–402

• Voltage testing Finished cable tested at 2000 VRMS between every two

conductors and between each conductor and the shield. 100% test.

ALuMinuM MYLAR ShiELD

11

binDER tAPE

JACKET

FiLLER

conDuctoRS

itEM no. WiRE inSuLAtion noM. DiA.

SiZE StRAnDS/AWg MAtERiAL coLoR MAtERiAL

4 14 AWG 19/25 COPPER BLACK TYPE “B” P.V.C. 600V Ø.105”

5 14 AWG 19/25 COPPER WHITE TYPE “B” P.V.C. 600V Ø.105”

6 14 AWG 19/25 COPPER RED TYPE “B” P.V.C. 600V Ø.105”

7 14 AWG 19/27 COPPER ORANGE TYPE “B” P.V.C. 600V Ø.105”

8 16 AWG 19/27 COPPER YELLOW TYPE “B” P.V.C. 600V Ø.091”

9 16 AWG 19/27 COPPER GREEN TYPE “B” P.V.C. 600V Ø.091”

10 16 AWG 19/29 COPPER VIOLET TYPE “B” P.V.C. 600V Ø.091”

11 16 AWg 19/29 tinnED coPPER bARE DRAin WiRE

Ø.600

CABLES

77-4017

37877.285.4466 toLL FREE

ASSEMBLYCabling - core- filler, as required to maintain a circular cross section

outer Layer - 6 wires, items 1-6 (2 #10 + 2 #12 + 2 #18 AWg)


Binder - overall clear polyster. 100% coverage

Tape shield - overall aluminum mylar foil 100% coverage - 20% overlap

Drain wire - item 7 is 18 AWg 16 strand tinned copper

Jacket - uV inhibiting polyvinyl chloride (PVc)

Overall diameter - Ø.565 ±.03

SPECIfICATIONS• Temperature rating –43°c to +80°c | stationary –55°c to +80°c


• Insulated conductors cSA AWM 1/11 6DoV FtA icEA S–61–402

• Cable uL. standard 1277. type Vntc. cSA Ft4

nEc 340. Sunlight resistant jacket 600 V rated

• Voltage testing Finished cable tested at 2000 VRMS between every

two conductors and between each conductor and the shield. 100% test.

FiLLER

JACKET

tAPE ShiELD

binDER tAPE

Ø.565 ±.03

conDuctoRS


SiZE StRAnDS/AWg StRAnDS/AWg MAtERiAL coLoR MAtERiAL

1 10 AWg 37/26 104/30 tinnED coPPER RED Ø.177”

2 10 AWG 37/26 104/30 TINNED COPPER BROWN Ø.177”

3 12 AWG 19/25 65/30 TINNED COPPER BLUE Ø.153”

4 18 AWG 16/30 16/30 TINNED COPPER GRAY Ø.107”

5 18 AWG 16/30 16/30 TINNED COPPER WHITE Ø.107”

6 12 AWG 19/25 65/30 TINNED COPPER BLACK Ø.153”

7 18 AWg 16/30 16/30 tinnED coPPER bARE DRAin WiRE

(PVC) .020” NOM. WALLnYLon .005 nDM WALL

(PVC) .020” NOM. WALLnYLon .005 nDM WALL

(PVC) .015” NOM. WALLnYLon .005 nDM WALL(PVC) .015” NOM. WALLnYLon .005 nDM WALL(PVC) .015” NOM. WALLnYLon .005 nDM WALL(PVC) .015” NOM. WALLnYLon .005 nDM WALL

PRiMARY SEconDARY

CABLES

77-4231 cable


ALuMinuMMYLAR ShiELD

binDER tAPE

JACKET

FiLLER

ASSEMBLYCabling - core-minimum filler to keep as flexible as practical

outer Layer - 10 wires, items 1-10 (3 #12 + 4 #14 + 3 #16 AWg)


Binder - 0.002” mylar tape - 25% minimum overlap

Tape shield - 0.002” aluminum mylar tape - 25% minimum overlap

Drain wire - item 11 is pulled under the shield

Jacket - uV inhibiting polyvinyl chloride (PVc)

Black 0.060” nominal wall

Overall diameter - Ø.665 ± 0.3”

SPECIfICATIONS• Temperature rating –55°c to +80°c


• Insulated conductors uL1015 cSA tRE2 iPcEA S–61–402

• Cable uL2653 cSA tR32 iPcEA S–61–402

• Voltage testing Finished cable tested at 2000 VRMS between every two

conductors and between each conductor and the shield. 100% test.

conDuctoRS


SiZE StRAnDS/AWg MAtERiAL coLoR MAtERiAL

1 12 AWG 19/25 COPPER BLACK P.V.C. 600V Ø.124”

2 12 AWG 19/25 COPPER WHITE P.V.C. 600V Ø.124”

3 12 AWG 19/25 COPPER GREEN P.V.C. 600V Ø.124”

4 14 AWG 19/27 COPPER BLACK P.V.C. 600V Ø.105”

5 14 AWG 19/27 COPPER WHITE P.V.C. 600V Ø.105”

6 14 AWG 19/27 COPPER RED P.V.C. 600V Ø.105”

7 14 AWG 19/27 COPPER ORANGE P.V.C. 600V Ø.105”

8 16 AWG 19/29 COPPER YELLOW P.V.C. 600V Ø.091”

9 16 AWG 19/29 COPPER GREEN P.V.C. 600V Ø.091”

10 16 AWG 19/29 COPPER VIOLET P.V.C. 600V Ø.091”

11 18 AWg 16/30 tinnED coPPER bARE DRAin WiRE

CABLES

Wc23012cLotWc23012DLot

39877.285.4466 toLL FREE

TYPE TC-COnTROL OR InSTRUMEnTATIOn CABLEPVC/nYLOn InSULATIOn WITh OVERALL PVC JACkET

SCOPEthis specification covers multiconductor cables having VW-1 tFFn

or thhn/thWn (PVc/nylon) conductors with an overall gas/

vapor-tight polyvinyl chloride (PVc) jacket, conforming to Article 318

“Cable Trays” and Article 340 “Power and Control Cable Type TC” of

the 1996 national Electrical code, and Standard 1277 of underwriters

Laboratories, inc. Meets the requirements of icEA t-29-520 and

t-30-520 flame tests as well as the 70,000 btu “cable tray

Propagation Test” per IEEE-383 and shows reserve capabilities by also

pass the 210,000 btu flame test. Rated 600 volts, 90°c dry and 75°

wet. uL file no. E60749. Also meets Ft4/iEEE 1202 70,000 btu test.

SPECIfICATIONSuL listed and oShA acceptable. Recognized for use in class 1 or 2,

Division 2 hazardous locations and for installation in trays, wireways,

troughs, channels, ducts and conduit. Specifically approved for

direct burial, wet or dry locations and outdoors in cable trays where

a sunlight resistant rating is required. Designed for control, power,

lighting, telemetering, signals and relay or traffic control.

CONSTrUCTIONConductors

bare soft annealed copper per AStM b-3

Sizes 18 and 16 AWg (tFFn)

Bunch stranded. Size 18 (16/.010”) and Size 16 (19/.0117”) UL-62

paragraph 10.2

Sizes 14, 12 and 10 AWg (thhn/thWn)

concentric stranded, class b (7 strands)

AStM b-8 and uL-83 table 13.1

Insulation

high dieletric polyvinyl chloride

uL-1581 table 50.145 (thWn 75°c)

uL-1581 table 50.155 (thhn 90°c)

uL-1581 table 50.155 class 12b (tFFn 90°c)

Thickness

uL-83 table 15.5 for thhn/thWn

uL-62 table 6.2 for tFFn

Insulation Armor

Nylon

uL-83 paragraph 25.1 for thhn/thWn

uL-62 paragraph 22.1 for tFFn thickness

uL-83 table 15.5 for thhn/thWn

uL-62 paragraph 26.4 for tFFn

CABLINGthree or more conductors are assembled round with fillers as

needed. A nylon rip cord is inserted under the jacket for ease of

stripping. two conductors are assembled flat parallel (round, with

fillers as needed, is available upon request).

Overall Jacket

gas/vapor-tight Polyvinyl chloride (black)

uL1277 table 10.1

Thickness

Specified herein

Color Coding

ICEA Method 3 Table K-2, except colors and numbers are

printed on solid base colors for easy identification.

Cable Identification

Sizes 18 and 16 AWg

ink print on one side of jacket

“(size) AWg type tc 90°c dry 75°c wet Sunlight Resistant 600V A.i.W.

Corp. (UL) Direct Burial”

indent print on other side of jacket

“(number of conductors)”

Sizes 14, 12, and 10 AWg

ink print on one side of jacket

“(size) AWg type tc thhn or thWn cdrs. Sunlight Resistant 600V

A.I.W. Corp. (UL) Direct Burial”

indent print on other side of jacket

“(number of conductors)”

Construction Options

consult factory for cable specifications with appropriate shields.

cables made per Dupont Spec. SE-33.4b also available.

CABLES

dIAGrAMS


PRoDuct # DEScRiPtion PARt #

Ac Alarm card, 120V, SL b7c51PAA

cb1 circuit breaker, 15A Eb152771cMDW

F1 Fuse, 7 Amp (some models, replaces cb1) FuFnM70g251

Mc Master card w/photocell b7c14RAA

MV1-2 Metal oxide Varistor, 150V 80 Joules MV150LA20

MV3 Metal oxide Varistor, 24V 4 Joules MV24ZA4

SW1 Day/Night/Auto Switch SZ22030251AK

tb1-E terminal block End (1 total) tbE230AA

tb1-S terminal block Section (4 total) tbS213AA01A

tbP Photocell terminal block, 2 Position tb02b038A07A

9LcA111L00AS

incoMing PoWER

SEE notE 1.

nEutRAL gRounD

LinE

PhotocELL RED PHOTOCELL BLACK

toWER nEutRAL obStRuction LightS(1-4 116W 120V LAMPS)

toWER gRounDbEAcon (2 620W 120V LAMPS)obS. LightS (2-4 116W 120V LAMPS)LoAD bALAncE RESiStoRtoWER nEutRALnEutRAL

gRounD

LinE

gRounD nEutRAL

LinE

inPut PoWER

toWER gounDStRobE LinEPhoto LinEtoWER nEutRAL

REDBLACK

PhotocELL

K1


Ac Alarm card, 120V, bcn-SL b7c21PAA

cb1-3 circuit breaker, 15A Eb152771cMDW

FbP Flasher by-Pass card, 120V b7c31PAA

K1 Relay, 12V Coil, 20 A, DPDT KA120DV2022C

K2-4 Solid State Relay, NO, 40A KR241DV4011R





tb1/2-E terminal block End (2 total) tbE230AA

tb1/2-S terminal block Section (9 total) tbS213AA01A



Ac Alarm card, 120V, Strobe b7c26PAA

cb1 circuit breaker, 15A Eb152771cMDW

K1 Solid State Relay, NO, 40A KR241DV4011R


MV1-3 Metal oxide Varistor, 150V 80J MV150LA20

MV4 Metal oxide Varistor, 24V 4J MV24ZA4





9LcD111000AS

9LcA001000AS

dIAGrAMS

43877.285.4466 toLL FREE

9LcA233L00AS

PH

OTO

CEL

L B

LAC

K A

nD

RED

Lin

E 1

Lin

E 2

in

co

Min

g g

Rou

nD

inc

oM

ing

nEu

tRA

Lto

WER

nEu

tRA

L

toW

ER g

Rou

nD

bEA

co

n 1

(2 6

20

W 1

20

V L

AM

PS)

bEA

co

n 2

(2 6

20

W 1

20

V L

AM

PS)

bEA

co

n 3

(2 6

20

W 1

20

V L

AM

PS)

LoA

D b

ALA

nc

E RE

SiSt

oR

1

LoA

D b

ALA

nc

E RE

SiSt

oR

2

LoA

D b

ALA

nc

E RE

SiSt

oR

3

ob

S Li

gh

t LE

VEL

1 (3

-4 1

16W

12

0V

LA

MPS

)

ob

S Li

gh

t LE

VEL

2 (3

-4 1

16W

12

0V

LA

MPS

)

toW

ER g

Rou

nD


Ac1 Alarm card, 120V, bcn-bcn-bcn b7c24PAA

Ac2 Alarm card, 120V, SL-SL b7c23PAA


FAn Fan, 120V A6A1010AF2

FbP1-3 Flasher by-Pass card, 120V b7c31PAA

K1-3 Relay, 12V Coil, 20 A, DPDT KA120DV2022C








tb1-nE terminal block End White, Large(1 total) tbE830AA

tb1-nS terminal block Section White, large (2 total) tbS824AA01A


9LcE233L0bASPRoDuct # DEScRiPtion PARt #

Ac1 Alarm card, 120V, ob-ob b7c23PAA

Ac2 Alarm card, 120V, bcn-bcn-bcn b7c24PAA

Ac3 Alarm card, 120V, St-St-St b7c28PAA

bc backup card, 120V b7c41PAA


FAn cooling Fan, 120V A6A1010AF2

Fb1-3 Flasher by-Pass card, 120V b7c31PAA

K1-3 Relay, 12V Coil, 20 A, DPDT KA120DV2022C


K13 Relay, 120V Coil, DP3T KA121AV0532C





SYnc Strobe Sync card b6A1101Pcb4b



tbn-E Large terminal block End (2 total) tbE830AA

tbn-S Large terminal block Section (18 total) tbS824AA01A


dIAGrAMS


Fg2000/2000b

LinE

gRounDnEutRAL

toWER gRounDbEAcon (2 620W 120V LAMPS obS. LightS (2-4 116W 120V LAMPSMEDiuM intEnSitY StRobELoAD bALAncE RESiStoRPhoto/hEAtER LinEtoWER nEutRAL

RED BLACK PhotocELL


Ac Alarm card, 120V, bcn-ob-St b7c25PAA

bc backup card, 120V b7c41PAA


FbP Flasher by-Pass card, 120V b7c31PAA

K1 Relay, 12V Coil, 20 A, DPDT KA120DV2022C


K5 Relay, 120V Coil, DPDT KA121AV0522C









Fh1 Flashhead complete, Fg2000 (white) *277-4045E

Fh1 Flashhead complete, Fg2009 (red) *277-4153E

Fh1 Flashhead complete, Fg2000b (white) *277-5047W

Fh1 Flashhead complete, Fg2009b (red) *277-5047R

Ft1 Flashtube Assembly 12S00602

b1 base Assembly (w/gasket & lens holders) *77-4103

G1 Lens Gasket, 14” AS568A-383

G2 Lower Cover Gasket, 11.5” AS568A-380

gL1 globe Assembly, Fg2000 (white) *77-4036-001

gL1 globe Assembly, Fg2009 & Fg2009b (red) *77-4036-003

gL1 globe Assembly, Fg2000b (white) *77-4036-002

ic1-2 insulator cups *77-4182

Fh1-6 Flashtube holder *77-4026

S1 interlock Switch *77-2644

tb1 terminal block Assembly *77-3965

t1 trigger transformer *77-4040W

Fg3000/3000b PRoDuct # DEScRiPtion PARt #

Fh1 Flashhead complete, Fg3000 *277-4173E

Fh1 Flashhead complete, Fg3000b *277-5004RW

Ft1-2 Flashtube Assembly 12S00602

b1 base Assembly (w/gasket & globe holders) *77-4103

G1 Lens Gasket, 14” AS568A-383

G2 Lower Cover Gasket, 11.5” AS568A-380

gL1 globe Assembly, Fg3000 *277-5095-004

gL1 globe Assembly, Fg3000b *277-5095-001

icL insulator cup, Lower *77-4182

icu insulator cup, upper *77-4181-001

Fth Flashtube holder *77-4026



K1 Trigger Transformer relay (FG3000 only) *77-4192

t1 trigger transformer, White *77-4040W

t2 trigger transformer, Red *77-4040R

9LcE111L0bAS

dIAGrAMS

45877.285.4466 toLL FREE


c1 capacitor, Resonating, 4uF *77-3911

c2 capacitor, Day, 70uF *77-3949

c3 capacitor, night, 5uF *77-4104

Db1 Diode board *277-3939

E1 Stainless Steel Enclosure, Fg2000/3000 *77-4219

F1 input Power Fuse, 4Amp *DP-1020

hV high Voltage board *277-3937

K1-2 Interlock & Day/Night Relay *77-2013

Mb1 Mother board *77-3967

Pc Photocell *77-3259

Pc1 Photocell w/socket *77-3259PcA

PS1 Flashguard 2000 PS, 120V 60hz *277-397161A

PS2 Flashguard 2000b PS, 230V 50hz *277-397153A

R1 Power Resistor, 50ohm, 55Watt *77-3959

R2-4 Power Resistor, 20ohm, 40Watt *77-2759


S2 interlock Switch Assembly *277-3990

SM1 Sync Monitor board *277-4116

t1 Power transformer, 120/240V 60hz *77-3970


t1 Power transformer, 240/480V 50hz *77-4138c

t2 current Sense transformer 40000679-001

tc1 trigger control board *277-4123

tF1 transformer Fuse, 630mA *DP-1019

Fg2000

hig

h Vo

LtAg

Ein

Dic

AtoR D

S1

SW1: A

uto

-RESEt tESt bu

tton

DS1: Lo

gic

PoW

ER (RED)

DS2

: FLASh

StAtuS (YELLo

W)

DS3

: co

MM

un

icAtio

n StAtu

S gREEn




c3 capacitor, night, 5uF cA505b661cDg


Dcc Digital controller board 40000031-003

E1 Stainless Steel Enclosure 40000678-003

F1-F2 input Power Fuse, 6Amp *77-1167

hV high Voltage/trigger board 34E00010-001


Mb1 Mother board *277-5053-002



R5 Power Resistor, 1.5kohm, 50Watt RW000002




t3 trigger Line Driver board *277-5105

t4 Logic transformer tP000005

t5 Power Line transformer 1A91324h34


Fg2000b AoL

dIAGrAMS


Fg2000b PRoDuct # DEScRiPtion PARt #



c3 capacitor, night, 5uF cA505b661cDg


Dcc Digital controller board 40000031-003

E1 Stainless Steel Enclosure 40000678-004

F1-F2 input Power Fuse, 6Amp *77-1167

hV high Voltage/trigger board 34E00010-001









t3 trigger Line Driver board *277-5105

t4 Logic transformer tP000005

t5 Power Line transformer 1A91324h34






cnV1 Dc-Dc converter, 24VDc-1000VDc *77-4128


E1 Stainless Steel Enclosure *77-4219

F1,F3 input Power/Sidelight Fuse, 12Amp *77-4136

hV high Voltage circuit card *277-4131



Pc Photocell w/21’ cable 12h00107

PS1 Flashguard 3000 Power Supply, 24VDc *277-417500L



SL1 Photocontroller/Sidelight Monitor Assembly 12h00109-1


SW1 interlock Switch Assembly *277-3990Dc




Fg3003

dIAGrAMS

47877.285.4466 toLL FREE

Fg2009


ALn Alarm Lockout Relay Assembly, Day (not shown) 35E00101






F1 input Power Fuse, 10Amp *77-2040

F3 Sidelight Fuse, 4Amp *DP-1020



K4 Sidelight Module Sensor *77-4196

K5 Sidelight Module Power Relay *77-4198


MP1 interlock Switch Assembly *277-3990

Pc Photocell, night *77-3258

Pc1 Photocell, night w/socket *77-3258PcA

R1 Power Resistor, 10kohm, 55Watt *77-3959



SLM1 Sidelight control Module (w/terminal block) *277-4195










c1 capacitor, Resonating, 4uF cA505b661cDg



E1 Stainless Steel Enclosure, Fg2000b/3000b 40000678-004

F1/F3 input Power Fuse, 6Amp *77-1167



K4 Sidelight Power Relay KA121AV0522C




PS1 Flashguard 2009b Power Supply, 120V 60hz 40000681-027

PS2 Fg2009b Power Supply, 120V – no Sidelight 40000681-028

R1 Power Resistor, 50ohm, 55Watt RW50Rb0500gF


R5 Power Resistor, 1.5kohm, 50Watt 40000683-001

R6-7 Power Resistor, 50kohm, 50Watt RW50Rb0502gF


S2 interlock Switch Assembly 40000677-001

SLM1 Sidelight control Module b7c23PAA




tc1 trigger control board *277-5014-003


Fg2009b

dIAGrAMS


Fg3000b







F1 input Power Fuse, 10Amp *77-2040

F3 Sidelight Fuse, 4Amp *DP-1020



K4 Sidelight Module Sensor *77-4196

K5 Sidelight Module Power Relay *77-4198


MP1 interlock Switch Assembly *277-3990



R1 Power Resistor, 10kohm, 55Watt *77-3959



SLM1 Sidelight control Module (w/terminal block) *277-4195










c1 capacitor, Resonating, 5uF cA505b661cDg

C2 Capacitor, Day, 70uf CA706A441EK



E1 Stainless Steel Enclosure, Fg2000b/3000b 40000678-004

F1/F3 input Power Fuse, 6Amp *77-1167



K3 Trigger Transformer Relay KA025DC10S2N

K4 Sidelight Power Relay KA121AV0522C




PS1 Flashguard 3000b Power Supply, 120V 60hz 40000681-033

R1 Power Resistor, 50ohm, 55Watt RW50Rb0500gF



R6-7 Power Resistor, 50kohm, 50Watt RW50Rb0502gF


S2 interlock Switch Assembly 40000677-001

SLM1 Sidelight control Module b7c23PAA

SLM1 Sidelight control Module, LED b7c23LAA-001






tc1 trigger control board *277-5014-003


Fg3000

dIAGrAMS

49877.285.4466 toLL FREE

SS-125


A1 high Voltage Supply board *277-3261

A2 trigger control board *277-3262

A3 Fault Monitor board *277-3263

c1 capacitor, 1uF, 1700V *77-4220

c2 capacitor, 12.5uF, 2500V *77-4108

c3 capacitor, 110uF, 2500V *77-4133-001

c4 capacitor, 3uF, 2500V *77-3311

Db1 Diode block *277-3342-6

DS1 interlock Assembly (w/ S1-S3) *77-3323

E1 Stainless Steel Enclosure, SS-125 *77-3296-02

F1 Fuse, Sb, 3.2A – 480V System *77-2041

F1 Fuse, Sb, 6A – 240V System *77-1167

F1 Fuse, Sb, 10A – 120V System *77-2040

F2-F5 Fuse, Sb, 1A, 3Ag *77-2365

Ft Flashtube Assembly *77-3295

FtS Flashtube Assembly with sockets *77-3295S

K1 Interlock Relay *77-2878

K2-K4 Mode Relays *77-2013

LA Surge Arrestor *77-4139

Mb Mother board *277-3264

R1-R6 Resistor block Assembly *277-3546

RA Reflector Assembly *277-3898


S2 Remote/Local Switch *77-2668

S3 Mode Switch (Day, twilight, night) *77-2667

t1 input transformer, 60hz *77-3890

t1 input transformer, 50hz *77-4244

t1-Sb t1 Voltage Selector block, 120V *77-3319



t2 trigger transformer Assembly *277-3324

Wh Wire harness Assembly *77-3355A


Mb Mother board, SS-122 *277-3047

A1 Sync & timing board *277-2673

A2 Digital Monitor board, 1-8 Lights *277-2536



K4-K5 Relay *77-2710

K1-3, K6-K7 Relay, 3PDT *77-3041

t1 Logic transformer *277-2214

t2 Power transformer, 240/480V, 50/60hz *77-2549



F1 Fuse, Sb, 10A *77-2040

SS-124 Photocell Assembly

PcELL Photocell Assembly, SS-124 *277-3247

PR Photocell Receptacle *77-3257

Pn Photocell, night *77-3259

Pt Photocell, twilight *77-3258

SS-122

dIAGrAMS



DL Dome Lens, red, beacon SFL150

uL upper Lens, red, beacon SFL125

LL Lower Lens, red, beacon (x2) SFL100

Eb Eyebolt Assembly 6A0002SAY

WS Wire Set Assembly A6A0001WA

uR upper beacon Rods (x3) b6A0002AF2

LR Lower beacon Rods (x3) A6A0002Ag

gS gasket Set (9 total) A6A0002AR

WT Watertight Connector, 1” WT4A037050TT

cb cable Assembly, #12-3c, 12 Feet A6A0001Wc12

Lh Lamp, beacon, 620 Watt, 120VAc Lh620120gE

Lh Lamp, beacon, 700 Watt, 230VAc Lh700230hDt

SK Socket, lamp, mogol, CSA, 2500W 240V XLFC5S300

SK Socket, lamp, mogol, 2500W 240V XL000001

KG114F0001


Mb-1 Micro-controller board, A-0 40000444-001

Mb-2 Micro-controller board, A-1 40000444-002

Mb-3 Micro-controller board, A-2/3 40000444-003

K1-K4 Solid State Relay, 50A, NC KM121AV50D2D

F1 0.1A 250V Slo-blo Fuse 40000408-001

F2-F5 12A 250V Slo-blo Fuse 40000409-001

F6 1A 250V Slo-blo Fuse *77-2365

F7, F8 5A 250V Slo-blo Fuse 40000410-001

F9-F11 12A 250V Slo-blo Fuse 40000409-001

PcELL Photocell, 120V, night *77-3258

Lc-5000

dIAGrAMS

to PhotocELL

SiDELight FAiLuREbEAcon FAiLuREFLAShER FAiLuRELightS ‘on’ PoWER FAiLuRE coMMon

51877.285.4466 toLL FREE


FB Fuse, Beacon, 15A FUKTK150601

FR Fuse, Load balance Resistor, 7A FuFnM70g251

FS Fuse, Sidelight, 5A FuFnM50g251

K2 Power Relay, Solid State, 30A, 120V KR241AV120NC

K5 Flasher By-Pass Relay Assembly A6C0015AG

KZ Beacon Flasher Assembly KZ1L1RR30A

Mb Mother board D6c0015Ab01

Pc Photocell Assembly PA446F21bS

Pi-PEcb Photo control board b6P0004AD

Wh Wire harness 6c0015Ah

tb1-E terminal block End tbE230AA

tb1-S terminal block Section tbS213AA01A

tb2-E terminal block End tbE330AA

tb2-F terminal block Section tbS213AA01A

tb2-S terminal block, Fusible tbS352AA01A

Mbc2161b45S


cc L-810 casting cover, painted, double c6A0008Ab2

cL Sidelight Latch Spring A6A0008AJ

cS L-810 casting, painted, single, bottom hub 15h00600-1

cS L-810 casting, painted, single, side hub c6A0005AA21

cS L-810 casting, painted, double, bottom hub c6A0008AA21

cS L-810 casting, painted, double, side hub c6A0022AA21

gS gasket, neoprene A6A0008Ag

LH Lens Holder Assembly with 7” chain B6A0008AA

LP Lamp, 116W, 120V Lh116120gE

LP Lamp, 116W, 230V Lh116230Dt

LS Lens, Red, fresnel, L-810 FL02b02810

LS Lens, clear FL0cb02810

LS Lens, Yellow FL04b02810

LS Lens, green (when lit) FL08b02810

LS Lens, blue (when lit) FL06b02861t

Lt Sidelight Latch A6A0008AD

Pn Sidelight Spring Pin PS07501002D0

PR 1” to ¾” Pipe reducer PR0304B4R

SS Lamp socket, porcelain, 660W, 250V XLcb4S2200

TR Transfer relay assembly with relay &sockets 6A0013SK3

tR-R transfer Relay, 0.3A coil 13Amp obRL100

ob20 SERiES

dIAGrAMS

ACCESSOrIES

ACCESSOrIES


9Lc contRoL SYStEM

APPLICATION9Lc series lighting controls combine the finest in digital circuitry with rugged

electromechanical hardware to yield the industry’s most comprehensive obstruction

lighting controls. Standard models are available for all common FAA and icAo

applications. the 9Lc’s modular design allows for custom controls for almost any

combination of flashing red beacons and sidelights. All models include a nEMA 4 outdoor

housing and a calibrated photocell for automatic day/night switching. A photocell override

switch is standard on all systems, facilitation troubleshooting or maintenance. All controls

provide comprehensive status indicators and alarm contacts for easy connection to remote

monitoring systems.

fEATUrES• Controls for multiple beacons flash all beacons simultaneously per FAA and

icAo specifications

• Lightning protection provided by:

- circuit breaker protection to all tower lighting circuits

- MoV surge suppressors on all inputs, outputs, and photocell lines

- torroidal current sensors isolate tower lines from monitoring circuitry

• Load balance resistor capability is available

• Modular design allows customization for nearly any application

• Dozens of models already developed for control of up to 14 beacons

• Standard with NEMA 4 enclosures (NEMA 4X optional upgrade)

ALArM CONTACTS / CONTrOL STATUS• Individual alarm contacts and control status is provided for:

- control power failure

- Day/night mode status

- Each flashing red beacon

- Each level of steady burning obstruction lights

- Flasher by-pass alarm/status for each beacon

• Number of lamps being monitored can easily changed by setting dip-switches

• Bi-color red/green LED status indicators provide instant indication of alarm and

control status

• Normally open and normally closed alarm contacts are both available

• Primary and auxiliary alarm contacts provided

Lighting StRuctuRE inPut VoLtAgE SiDELight LbRMoDEL # SYStEM tYPE hEight (50/60hZ) bEAconS StRobES LEVELS cAPAbiLitY

9LcA001000AA FAA A-0 incandescent 0 - 150’ 120V 0 1 no

9LcA111L00AA FAA A-1 incandescent 151’ - 350’ 120V 1 1 Yes




9LcD111000AA FAA D-1 Strobe 200’ -350’ 120V 1 no

9LcD231000AA FAA D-2 Strobe 351’ - 500’ 120V 3 no

9LcE111L0bAA FAA E-1 inc/Strobe 200’ -350’ 120V 1 1 Yes

9LcE233L0bAA FAA E-2 inc/Strobe 351’ - 500’ 120V 3 3 Yes

9LciA06000AA icAo A-0 incandescent 0 - 150’ 230V 1 no

9Lcib16L00AA icAo A-1 incandescent 151’ - 350’ 230V 1 1 Yes

9Lcib26L00AA icAo A-2 incandescent 350’ – 700’ 230V 2 1 Yes

9Lcic16L00AA icAo A-1 incandescent 151’ - 350’ 230V 1 2 Yes

9LciD16L00AA icAo A-1 incandescent 151’ - 350’ 230V 1 3 Yes

9LcR001000AA FAA A-0 LED 0 - 150’ 120V 1 no

9LcR111000AA FAA A-1 LED 151’ - 350’ 120V 1 1 no



ACCESSOrIES

55877.285.4466 toLL FREE

APPLICATIONthe Lc-5000 series lighting controls combine the finest in digital circuitry with rugged

microprocessor based hardware to yield the industry’s most comprehensive obstruction

lighting controller. the Lc-5000 design allows for quick installation. the ‘auto-configure’

design will evaluate the lighting on the tower and configure itself to operate and monitor

installed lighting. All models include a nEMA 4 outdoor housing and a calibrated

photocell for automatic day/night switching. A photocell override switch is standard on all

systems, facilitation troubleshooting or maintenance. All controls provide comprehensive

status indicators and alarm contacts for easy connection to remote monitoring systems.

fEATUrES• Controls for multiple beacons flash all beacons simultaneously per FAA and

icAo specifications

• Lightning protection provided by:

– circuit breaker protection to all tower lighting circuits

– MoV surge suppressors on all inputs, outputs, and photocell lines

– torroidal current sensors isolate tower lines from monitoring circuitry

• Diagnostic LED Tree provides instant verification of beacons and sidelights

• Modular design allows customization for nearly any application

• Dozens of models already developed for control of up to 14 beacons

• Standard with NEMA 4 enclosures (NEMA 4X optional upgrade)

ALArM CONTACTS / CONTrOL STATUS• Bi-color red/green LED status indicators provide instant indication of

alarm and control status

• Normally open and normally closed alarm contacts are both available

• Primary and auxiliary alarm contacts provided

Lc-5000 RED Lighting

contRoLLER

ENVIrONMENTALTemperature -55° c to +55° c, -67° F to + 130° F

humidity 95% relative humidity

Will withstand exposure to: Wind-blown rain

from any angle

Wind speed of 240kph (150mph)

nEMA Rating nEMA 4

Weight 10 lbs.

MoDEL nuMbERS SYStEM tYPE inPut VoLtAgE

Lc5000-001 incandescent or LED A-o 120V or 240V

Lc5000-002 incandescent or LED A-o or A-1 120V or 240V

Lc5000-003 incandescent or LED A-o or A-1 or A-2 120V or 240V

FRont ViEW

SiDE ViEW

dIMENSIONAL dIAGrAMS

ACCESSOrIES


Lightning SuRgE PRotEction DEVicE - LSPD-3000b

APPLICATIONLSPD devices are designed to protect all the FlashguardtM medium intensity strobe lighting

systems. the LSPD provides both a grounding solution and surge suppression for these

installations. the LSPD minimizes exposure to lightning damage through tower light wiring,

a lightning path that is commonly overlooked at communications sites. Without the use of

a LSPD, the interconnecting cable between the strobe’s flashhead and the power supply

provides a direct path that can allow damaging surges and transients to enter the shelter.

Sites with LSPDs installed have proven reliability. Sites with previous lightning problems

have recorded hundreds of lightning strikes after LSPD installation, with no damage to the

power supply or communication equipment.

INSTALLATIONLSPD units are installed between the flashhead and the power supply, providing protection

for both the lighting power supply and the telecommunications equipment installed at

the site. the LSPD units are supplied in a fiberglass nEMA 4X outdoor enclosure. the

protectors should be mounted on the tower above the ice bridge, before the cable turns

to enter the shelter. the first level of protection forces any induced voltage on the cable’s

shield to tower ground. All lines then pass through a surge suppression device before

continuing to the power supply. Detailed installation instructions are included with each

unit and should be adhered to for optimum protection.


icAo type: Medium intensity type b (L-864)

Compliant to: canadian Aviation Regulation (cAR) 621.19 DgAc of Mexico

icAo Annex 14, cAR 621.19

SPEciFicAtionS:

Response time Less than 5 µs.

current Withstand 40 kA per mode; iEEE c62.41 8x20µs short circuit waveform

circuitry the LSPD is series wired with parallel protection. Robust MoVs protect all circuits. Large ground plane bonded to a

#2 copper ground lug provides a strong electrical/ mechanical discharge point.

SERiES 800 Photocontroller & beacon FlasherAPPLICATIONthe hughey & Phillips SERiES 800 Photocontroller and beacon Flasher provides a low cost,

high reliability solution to your lighting needs. this unalarmed system allows for the user to

add an inline system to their conduit run on the tower to controller the installed FAA beacons

and sidelights. the systems are factory calibrated and never need adjustment. Each system

utilizes surge and transient components and additional input line protection. normally

closed solid state relay configuration assures “Lights ON” condition even if the circuitry fails.

Red LED provides quick visual verification of field operation. And with its modular design, it

allows for quick field installation or retrofit to existing system if ever damaged.

Spare Partshughey & Phillips is the oEM

for all your needs

• Flashtubes

• Cables

• Wire Harnesses

• Junction Boxes

• Lamps

• Relays

• Capacitors

• Lightning Rods

• Transformers

• Ice Shields

• BracketsMoDEL nuMbERS DEScRiPtion

S800Pc120 Photo controller, 120VAc

S800Pc240 Photo controller, 240VAc

S800bF120 beacon Flasher, 120VAc

S800bF240 beacon Flasher, 240VAc

ACCESSOrIES

APPLICATIONcombining technology with ease-of-use, hughey & Phillips’ third-generation gPS unit

combines flash synchronization and day-night sensing, and can be installed with just one

plug-in cable. this eliminates the need to mount a separate gPS unit, antenna, junction

box and wiring. Reliable, glitch-free operation is assured, using a crystal and the 50/60hz

power line as a zero-drift timing reference if the satellite signal is momentarily lost. And

two different flash modes are provided: fixed 40FPM or bit-switch selectable 24, 30, 40

or 60 FPM. the unit easily mounts with four screws to any surface, or pole mount using

the optional bracket. installation interconnect cable with quick connect plugs from gPS

unit to controller unit. LEDs indicate Power, Sync and gPS Lock status. With rugged metal

weatherproof and a battery-free design, hughey & Phillips’ gPS unit will provide years of

reliable service for your wind farm.

FAA Advisory circular Ac 150/5345-43F

canadian Aviation Regulation 621.19

icAo Annex 14, MiL-c-7989, DgAc of Mexico

gPS SYnc / PhotocELL

MoDuLE

SPEciFicAtionS SPEciFicAtionS

Input Voltage 100-132VAC 50/60Hz, 10W max. External Dimensions 6-1/4” x 6-1/4” x 4-1/8”

Enclosure NEMA 4 Painted Aluminum Mounting Dimensions 5-1/8” x 6-3/4”

operation temperature -40° to +55° c (4) #8 holes

indicators Power (green)

GPS Lock (Yellow) Optional Mounting 1-1/4” to 2-3/4” Pole

SYnc (Flashing Red) bracket

SYnc output 15-27VDc, 100mA, 3ms pulse

SYnc Adjustments Day: 40FPM

night: 24, 30, 40, 60 FPM

backup SYnc internal crystal clock or

Ac Line

PARt nuMbERS PARt nuMbERS

40002075-001 gPS SYnc Module 40002074-003 gPS cable, 100’

*77-3259 Photocell, 120V, 35-60 ft-cd 40002074-004 gPS cable, 150’

40002074-001 gPS cable, 25’ 40002074-005 gPS cable, 350’

40002074-002 GPS Cable, 50’ 40002082-001 Pole Mounting Kit

57877.285.4466 toLL FREE

ACCESSOrIES


APPLICATIONthe Lightning Rod Assembly, LRb58L7510M, is designed for, and

is widely used on antenna towers associated with microwave relay

installations, high-definition broadcast towers, and other structures

prone to lightning strikes. Consisting of a 7/8” diameter rod and a

base mounting ring designed for ready installation under existing

medium intensity lighting fixtures with a 13-1/4” bolt hole pattern.

the A6A0302Ab Lightning Rod extends approximately two feet

above a standard 300mm code beacon in order to reduce the

probability that lightning will strike the lighting fixture. this will

minimize the possibility of damage to the lighting fixture and the

wiring from cloud to ground lightning strikes

EASE Of INSTALLATIONthe base mounting ring is designed for installation underneath the base

of a medium intensity lighting fixture with a 13-1/4” bolt hole pattern

without requiring additional holes in the tower. it is only necessary to

remove two of the four mounting bolts in order to install the ring under

the existing fixture. the other two beacon mounting bolts must be

loosened sufficiently to enable the installer to slide the lightning rod

mounting ring under the fixture. Slotted holes are provided in the base

mounting ring in order that the ring may be rotated to avoid interference

with the tower bolts or details. the mounting ring should be positioned

so that the rod is located at either side of the fixture in order to avoid

interference during opening of the fixture for maintenance.

GENErALthe base mounting ring is an aluminum casting, tapped to accept

the threaded rod. The rod is fabricated from 7/8” diameter material

threaded at one end for insertion into the mounting ring. the rod is

specially treated after fabrication to withstand weathering

Lightning RoD ASSEMbLY

MOUNTING BRACKET FoR DuAL Lighting

bEAcon

DoubLE bEAcon/StRobE

StRobE

toWER

BEACOn/STROBE MOUnTIng BRACkET

StRobE MountingBRACKET FOR:

1. Model KG114 - Red Beacon

2. Model KG225 - Strobe

3. Model Fg2000 - Strobe

4. Model Fg3000 - Strobe

Mounting bracket will accommodate vertical tower members from 1.5” to 4.5” in diameter. Standard “U”– bolts are used to secure the bracket to the tower.

Material: galvanized steel

SuPPoRt AngLEtoWER LEg

“U”– boLtS

EXPAnDED MEtAL – PARtiALLY oMMittED FoR cLARitY oR iLLuStRAtion

SuPPoRt AngLE

SECURING BRACKET

BEACON/STrOBE ICE SHIELd ASSEMBLY

to mount beacon or strobe to the bracket, use h&P mounting assembly Part number – A6A0001SE

Part # KG 0926M001

PARt nuMbERS:

LRb58L7510M Lightning Rod Assembly

A6A0302A13 Lightning Rod

A6A0302AA2 Mounting Ring

nh7510cb2 Jam nut

Mounting Ring

Lightning RoDJAM nut

ACCESSOrIES

LoAD bALAncE RESiStoRLb112120 – 120V, 1200WAPPLICATIONthe proper operation of electrical and electronic devices in general

is based on the availability of a relatively steady line voltage. this

condition is usually met without special precaution when the several

connected loads all consume a steady amount of power. if one

or more of the loads are of a varying or pulsating nature, then the

degree of steadiness of the line voltage (i.e. line voltage regulation)

will be dependent upon several factors – such as:

• The voltage regulation of the power service to the installation

(i.e. is the power service a firm-heavy source with adequate

capacity or a soft source at the end of a rural line).

• The size of the conductors between the power service and the

connected load. in many cases the size is not adequate for the

load, thus causing a large voltage drop.

• The size and voltage regulation of the standby generator.

• The relative size of the pulsating load as related to the total

connected load at site.

Also of prime importance is the relative sensitivity of the electronic

or radio equipment to the variations in the line voltage. the rules

of the Fcc and FAA require the 300mm beacon to flash on and

oFF at a rate between 20 and 40 flashes per minute. the beacon

normally uses two 620 watt lamps, thus a pulsating load of 1240

watts. Assuming a rate of 30 FPM, the 1240 watt load is on for

1-1/3 seconds and oFF for 2/3 seconds. Due to some inrush

current when the lamps are on, the effect on the line voltage may

be slightly more severe than flashing a resistive load of 1240 watts.

in some installations, the 1240 watt pulsating load may represent

a substantial portion of the total connected load. in these cases

the variations in the line voltage may be quite severe and some

corrective means must be considered. Fortunately, a relatively simple

and quite effective corrective means is available – a Load balance

Resistor. this consists of a 1200 watt resistive load which is switched

on as the beacon load is switched oFF and vice versa.

the hughey and Phillips Lb112120 and Lb212480 Load balance

Resistors (LbR) are designed for use with flashing beacons and will

minimize fluctuations in the beacon lighting load circuit, when used

is conjunction with our 9Lc Lighting controls. housed in a louvered

galvanized steel case, the LbR is suitable for outdoor installations.

the mounting brackets are movable in order to provide for mounting

against a vertical or horizontal surface. connection to the LbR is

made to a terminal strip mounted in a watertight cast junction box

which is tapped for ½” conduit or conduit fitting. The resistive

elements are of the strip type to provide uniform heat distribution

and are of steel-sheath construction with compressed insulation.

Siteguard® Wc-60 Wireless Monitoringhughey & Phillips’ Digital cellular communicators deliver secure,

reliable and complementary digital communications via the gSM

(global System for Mobile) network.

this groundbreaking communications solution offers full data

reporting and uploading/downloading with most hughey & Phillips

control panels. in addition, with onboard zone inputs and optional

dialer capture capability, we’re compatible with other manufacturers’

security panels as well. All signals are delivered to the Alarmnet

network control center, which routes the information to the

appropriate central station. the state-of-the-art Alarmnet network

control center is fully redundant and monitored 24/7. Alarmnet has

the ability to route messages using Alarmnet-i and

800 PLuS services, providing true redundancy and multi-path

message delivery.

Siteguard® monitoring services handles all of the time dependent

monitoring tasks without requiring your interaction: if a light “burns

out”, Hughey & Phillips’s system does the following:

• Dry contact output is read into the SiteGuard System

• SiteGuard initiates alarm call over a GSM wireless connection

• Alarm received at ProtectionNet Network operations center, with

operators providing around the clock, 365 days a year service

• ProtectionNet initiates an FAA Notice to Airmen (NOTAM) for any

appropriate lighting failure

• The client is notified of the failure via telephone, voicemail, pager,

fax or e-mail

• With the NOTAM in place, you can now work at your own schedule

to repair the light outage

• If after 14 days we have not heard from you, we will contact you to

determine the status of your tower

• We will file the NOTAM extension if necessary or we will remove

the notAM, with no additional work from you

Wind turbine Switchthe hughey & Phillips Wind turbine Switch (WtS)

is designed to operate the required obstruction

lighting from either the high voltage generated

by the wind turbine within the nacelle or from

the commercial power supplied at the base of

the tower. utilizing patent-pending technology,

the WtS senses the highest voltage present and

powers the obstruction lighting at either 120VAc

or 230VAc. the WtS harnesses the power of wind to power your

obstruction lighting requirements.

PARt nuMbERS:

obMiSc215 Digital cellular communicator (Siteguard Wc-60)

obMiSc236 gSM Antenna, outdoor, gSM-Ant3Db, omni-directional

SMiSc234 gSM Adapter cable, WA7626-cA SMA to n Adapter

Mc000017 gSM coaxil cable, 25’

59877.285.4466 toLL FREE


Junction boXESWeathertight cast Aluminum for Surface Mounting

GENErAL INfOrMATIONhughey & Phillips Weathertight Junction boxes are of cast aluminum.

Each box is of adequate size for the number of terminals to enable

proper and simplified installation. All boxes are furnished complete with

cover, gasket, cover retaining chain and self-retaining type cover screws.

Tapping - hughey & Phillips Weathertight Junction boxes are

available with or without tapped conduit hubs. in ordering,

specify size.

Terminals - hughey & Phillips Weathertight Junction boxes are

available with standard screw type terminal blocks, or special blocks

dESCrIPTIONcast aluminum, watertight, complete with cover and screws, gasket,

and cover retaining chain. Available with or without terminal block,

and/or cable support.

SPECIfICATIONSInside Dim. (Approx.) 5 3/8” Dia. 2 5/8” Depth

Capacity 5 Term. (Kulka No. 603-5)

7 term. (buchanan type hD)

Max. Hub Tap 1” Cond. Size

dESCrIPTIONcast aluminum, watertight, complete with cover and screws, gasket,

and cover retaining chain. Available with or without terminal block,

and/or cable support.

SPECIfICATIONSinside Dim. (Approx.) L 4 7/8”, W 7”, D 4”

Capacity 8 Term. (Kulka No. 603-8)


Max. Hub Tap 1” Cond. Size

JUNCTION BOx NO. JC00000000JUNCTION BOx NO. JB00000000

with split connectors, or combinations, to customer order. the

terminal capacity indicated under each type of box is representative

of one type terminal block…all terminal strips are insulated.

Insulated Cable Supports - hughey & Phillips Weathertight Junction

boxes are available with built-in cable support (with or without

terminals) to meet requirements of the national Electric code.

Insulated Bushing - hughey & Phillips will install, when specified,

plastic insulating bushings inside of tapped conduit hubs.

ACCESSOrIES

dESCrIPTIONcast aluminum, watertight, complete with cover, cover screws,

gasket, and cover retaining chain. Available with or without terminal

blocks, and/or cable support, screw-cap receptacles, etc. Furnished

with mounting bars or mounting clamps, if specified on order.

SPECIfICATIONSInside Dim. (Approx.) L 10”, W 9”, D 5”

Capacity 20 Term. (2-Kulka No. 603-10)


**Max. Hub Tap Sides (R, L**) 1” Top & Bottom

(T, B**) 2” Cond. Size

JUNCTION BOx NO. Jf00000000

dESCrIPTIONcast aluminum, watertight, complete with cover, cover screws,

gasket, and cover retaining chain. Available with or without terminal

blocks, and/or cable support, screw-cap receptacles, etc. Furnished

with mounting bars or mounting clamps, if specified on order.

SPECIfICATIONSInside Dim. (Approx.) L 15”, W 9”, D 5”

Capacity 30 Term. (3-Kulka No. 603-10)


**Max. Hub Tap Sides (R, L**) 1” Top & Bottom

(T, B**) 2” Cond. Size

JUNCTION BOx NO. JG00000000

*order junction boxes by number, and specify hub tapping**,

number & type of terminals, & with or without...cable support,

insulating bushings, receptacles, mounting rails, etc.

*Maximum hub taps indicated are for standard boxes. Larger hub

size and taps available on special order.

METHOd Of SPECIfYING CONdUIT HUB TAPS

conduit hub tap Location Symbols

XX tRbL X 00 XX (type (taps) (cable (# of term box) Support Pos block) optional)

conDuit SiZE SYMboLS

conduit Size 1/2” 3/4” 1” 1 1/4” 1 1/2” 2”

ordering Symbol 2 3 4 5 6 7

Example: cat. no. Jc type box to be topped 1 1/4” top and bottom

and 3/4” left side only.

Order As: Junction box cat. no Jc5053c03b

Junction boXESWeathertight cast Aluminum for Surface Mounting

61877.285.4466 toLL FREE

ACCESSOrIES

K-Z Series Beacon Flasher

conforms to FAA and Fcc specification. completely calibrated to applicable FAA/Fcc

specifications by factory technicians. no field adjustment ever necessary.

Ultra reliable: surge and transient resistance components.

High power: rating 2.0KW maximum continuous tungsten load at up to 131° F (+55°C)

ambient air temperature 120 or 240 VAc option per circuit.

flash rate: 30 FPM; 2/3 on, 1/3 off duty cycle.

fail safe operation: normally closed solid state relay configuration assures “lights on”

condition even if control circuitry fails.

Visible operation indicator red LED (light emitting diode) provides instant visual

verification of field operation.

Modular construction: Easy field installation or retrofit for existing applications. Easy

replacement if damaged.

SPECIfICATIONSInput Voltage: 120 VAc 1 0 / 240 VAc 1 0

Power Rating: 2000 Watts maximum, continuous duty (zero voltage switching)

flash rate: 30 FPM; 2/3 on, 1/3 off duty cycle

Peak Current Surge: 320 Amps’ 100 milliseconds, 650 amps, 1 cycle @ 60 hz

(non repetitive)

Operating Temperature: -55°c to +55°c

Transient Suppression: 2.5 KV@ 10 milliseconds components to case

Reliability: MtbF over 500,000 hrs (SSR) per MiL-217c

List of Standard Solid State Beacon flashers


KZ1L10R30A 1-Beacon 120V

KZ2L10R30A 1-Beacon 240V

KZ1L1RR30A 1-Beacon & Load Balance Resistor 120V

KZ2L1RR30A 1-Beacon & Load Balance Resistor 240V

KZ1L20E30A 2-Beacon Simultaneous 120V

KZ2L20R30A 2-Beacon Simultaneous 240V

KZ1L2PR30A 2-Beacon Alternate 120V

KZ2L2PR30A 2-Beacon Alternate 240V

KZ1L2SR30A 2-Beacon & 2 Load Balance Resistor Simultaneous 120V

KZ2L2SR30A 2-Beacon & 2 Load Balance Resistor Simultaneous 240V

KZ1L2QR30A 2-Beacon & 2 Load Balance Resistor Alternate 120V

KZ2L2QR30A 2-Beacon & 2 Load Balance Resistor Alternate 240V

KZ1S3T030BA 3-Beacon Simultaneous 120V

KZ3S3T030B 3-Beacon Simultaneous 240V

KZ1S3T030A 3-Beacon Sequential 120/208V

KZ2L4N03BA 4-Beacon Simultaneous 240V

KZ1L4NR30A 4-Beacon 2+2 180°Apart 120V

KZ1S4N030AA 4-Beacon Sequential 120/208V

KZ1S5N030AA 5-Beacon Sequential 120/208V

KZ1S5N030A 5-Beacon 4 Position 120/208V (2 Beacon Top)

KZ1S6N030AAB 6-Beacon 4 Position 120/208 V (3 Beacon Top)

KZ1S7Z030B 7-Beacon 120/208 V (Top & Bottom Flash Together)

KZ1S7U030A 7-Beacon 5 Position 3 Beacon Top 120/208V


ACCESSOrIES

LIGHTINGSYSTEMS


LIGHTING SYSTEMS

65877.285.4466 toLL FREE

LIGHTING SYSTEMS


LIGHTING SYSTEMS

67877.285.4466 toLL FREE

LIGHTING SYSTEMS


LIGHTING SYSTEMS

Hughey & Phillips is

a global leader in the

design and manufacturing

of obstruction lighting

technology. We engineer

and design a complete

line of low, medium and

high intensity lighting

technology solutions

for radio, television,

and communication

towers; wind turbines; buildings; smokestacks; bridges;

and other obstructions to aerial navigation. All products are

manufactured by hughey & Phillips in the uSA. With a full

engineering staff providing complete support and design in

optical, electrical and mechanical disciplines to customize any

of our products to fit our customers’ unique needs. to learn

more, visit www.hugheyandphillips.com

69877.285.4466 toLL FREE

LIGHTING SYSTEMS

hughey & Phillips offers a vast selection repair services

for tower lighting controllers, flashheads and beacons.

our repair service department offers customers a fast and

economical method to overhaul their fielded equipment

for years of operation.

A G LO B A L L E A d E rr E PA I r S E r V I C E S


LIGHTING SYSTEMS

71877.285.4466 toLL FREE

LIGHTING SYSTEMS

LIGHTING SYSTEMS


LIGHTING SYSTEMS

73877.285.4466 toLL FREE

LIGHTING SYSTEMS


LIGHTING SYSTEMS

75877.285.4466 toLL FREE

fAA STANdArdS

notes:

1. the overall height of the structure including all appurtenances such as rods, antennas, obstruction lights, etc.,

determines the number of light levels.

2. the red obstruction lighting system is composed of flashing omnidirectional beacons (L-864) and/or steady burning

(L-810) lights. When one or more levels is comprised of flashing beacon lighting, the lights should flash simultaneously.

3. the chart above illustrates the requirements for standard lighting of towers and supporting structures in accordance

with FAA Advisory circular 70/7460-1; chapters 3, 4, 5, and 12.

Red obstruction Lighting Standards (FAA Style A)Day Protection = Aviation orange / White Paintnight Protection = 2,000cd Red beacon and sidelights


351’ - 700’

= L-810 obStRuction Light

A-2 A-3 A-4 A-5 A-6

= L-864 FLAShing bEAcon

701’ - 1050’

1051’ - 1400’

1401’ - 1750’

1751’ - 2100’

A-1A-0

151’ - 350’

0’ - 150’

fAA STANdArdS

high intensity obstruction Lighting Standards (FAA Style b)Day Protection = 200,000cd White Strobe

twilight Protection = 20,000cd White Strobenight Protection = 2,000cd White Strobe

notes:

1. the height of the main structure excluding all appurtenances such as rods, antennas, obstruction lights, etc.,

determines the number of light levels. Note: Any appurtenances over 40 feet (12 meters) requires additional lighting,

consisting of a Medium Intensity L-865 White Strobe, see FAA Style C.

2. When high intensity white lights are operated 24 hours a day, other methods of marking and lighting may be omitted.

this system should not be recommended on structures 500 feet (153 meters) AgL or less unless an FAA aeronautical

study shows otherwise.



351’ - 700’

B-2 B-3 B-4 B-5 B-6

701’ - 1050’

1051’ - 1400’

1401’ - 1750’

1751’ - 2100’

= L-856 high intEnSitY StRobE (3 FLAShhEADS REQUIRED PER LEVEL FoR 360o coVERAgE)

79877.285.4466 toLL FREE

fAA STANdArdS

notes:

1. the height of the main structure excluding all appurtenances such as rods, antennas, obstruction lights, etc.,

determines the number of light levels. Note: Any appurtenances over 40 feet (12 meters) requires additional lighting,

consisting of a Medium Intensity L-865 White Strobe.

2. When high intensity white lights are operated 24 hours a day, other methods of marking and lighting may be omitted.

this system should not be recommended on structures 500 feet (153 meters) AgL or less unless an FAA aeronautical

study shows otherwise.



high intensity obstruction Lighting Standards (FAA Style c)Day Protection = 200,000cd White Strobetwilight Protection = 20,000cd White Strobenight Protection = 2,000cd White Strobe


C-2 C-3 C-4 C-5 C-6

501’ - 700’

= L-865 MEDiuM intEnSitY STROBE REQUIRED APPuRtEnAncES oF 40 FEEt oR gREAtER

= L-856 high intEnSitY StRobE (3 FLASHHEADS REQUIRED PER LEVEL FoR 360o coVERAgE)

701’ - 1050’

1051’ - 1400’

1401’ - 1750’

1751’ - 2100’

fAA STANdArdS

Medium intensity White obstruction Lighting Standards (FAA Style D)

Day/twilight Protection = 20,000cd White Strobenight Protection = 2,000cd White Strobe

Painting of tower is typically not required

notes:



2. the medium intensity flashing white light system is normally composed of flashing omnidirectional lights. this system

is not normally recommended on structures less than 200 feet AgL.



351’ - 500’

200’ - 350’

1/2 but not LoWERthAn 200 FEEt (61M)

= L-865 FLAShing WhitE StRobE

D-1 D-2

81877.285.4466 toLL FREE

fAA STANdArdS

Medium intensity Dual obstruction Lighting Standards (FAA Style E)Day/twilight Protection = 20,000cd White Strobenight Protection = 2,000cd Red Strobe and SidelightsPainting of tower is typically not required

351’ - 500’

200’ - 350’

1/2 but not LoWERthAn 200 FEEt (61M)

= L-864/L-865 FLAShing DuAL (WhitE/RED) StRobE

= L-810 obStRuction Light

notes:



2. the dual lighting system includes red lights (L-864) for nighttime and medium intensity flashing white lights (L-865)

for daytime and twilight use. this lighting system may be used in lieu of operating a medium intensity flashing white

lighting system at night. Some populated areas where the use of white medium intensity at night may cause significant

environmental concerns, the use of the dual lighting system should reduce/mitigate those concerns.




E-1 E-2

fAA STANdArdS

notes:

1. the height of the main structure excluding all appurtenances such as rods, antennas, obstruction lights, etc., determines the number of

light levels. Note: Any appurtenances over 40 feet (12 meters) requires additional lighting, consisting of a Medium Intensity L-865 White

Strobe and a L-864 Red Beacon.

2. this dual lighting system includes red light (L-864) for nighttime and high intensity flashing lights (L-856) for daytime and twilight

use. this lighting system may be used in lieu of operating a high intensity flashing white lighting system at night. there may be some

populated areas where the use of high intensity lighting may cause significant environmental concerns. the use of the dual lighting

system should reduce/mitigate those concerns.

3. the chart above illustrates the requirements for standard lighting of towers and supporting structures in accordance with FAA Advisory

circular 70/7460-1; chapters 3, 4, 9, and 12.

Dual high intensity obstruction Lighting Standards (FAA Style F)

Day Protection = 200,000cd White Strobetwilight Protection = 20,000cd White Strobe

night Protection = 2,000cd Red beacon and Sidelights

501’ - 700’

= L-810 RED obStRuction Light

f-2 f-3 f-4 f-5 f-6

= L-864 FLAShing RED bEAcon

= L-856 high intEnSitY StRobE (3 FLASHHEADS REQUIRED PER LEVEL FoR 360o coVERAgE)

701’ - 1050’

1051’ - 1400’

1401’ - 1750’

1751’ - 2100’

83877.285.4466 toLL FREE

fAA STANdArdS


fAA STANdArdS

bRiDgE AnD WinD tuRbinE Lighting

L-864 or L-865 or(L-864 / L-865)

FRont ViEW SiDE ViEW

notES

85877.285.4466 toLL FREE


notES

notES

87877.285.4466 toLL FREE

THE EVOLUTION Of A BrANdFor more than 75 years hughey & Phillips has earned a

reputation for quality, dependability and innovation in

obstruction lighting around the globe.

Wind turbinesbroadcast telecommunications

ABOUT OUr COMPANYhughey & Phillips is a leader in the design and

manufacturing of obstruction lighting technology.

We produce a complete line of lighting solutions that

provide illumination for aerial navigation around the

world. And we offer complete power and lighting

systems designed and manufactured in the uSA. our

cost-effective obstruction lighting technology provides

highly efficient and reliable lighting solutions. by

offering complete support and design in electrical,

optical and mechanical disciplines, hughey & Phillips

can fully customize any product to fit the unique needs

of any customer.

877.285.4466 toLL FREE

937.652.3500 tELEPhonE 937.652.3508 FAX

HUGHEYAnDPHILLIPS.coM240 W. twain Aveurbana, oh 43078

tall Structures utilities

1930’s – 1970’s 1970’s – 2000 2000 – Present

obstruction lighting catalog

Documents