october 7 -10, 2007 radisson fort mcdowell resort ... · product requirements drive the need for...
TRANSCRIPT
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Designing a Cleanroom to Accommodate Roll-to-Roll Processing Equipment
Presented by:
Mark StrnadVice President Operations and Engineering
October 7-10, 2007Radisson Fort McDowell ResortScottsdale, Arizona USA
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 2 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Overview
• Cleanroom design continues to advance as technology changes. Product requirements drive the need for cleaner air, gases, liquids, and power. Concurrently, the use of roll-to-roll equipment is becoming more attractive. However, roll-to-roll equipment presents another set of challenges due to special size and material handling needs. This presentation will discuss how to design a cleanroom that will operate with both sophisticated products and roll-to-roll equipment.
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 3 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
The Challenge – Start with roll-to-roll technology
Photo Courtesy of Hanita Coatings
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 4 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Add in this tool size
Photo Courtesy of Energy Conversion Devices
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 5 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
And put it in a clean environment
Photo Courtesy of the Flexible Display Center at ASU
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 6 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Key Terms
We will start by defining and illustrating a few key terms as used in this presentation.
• Geometries– Minimum dimension that needs to be produced to create a given
technology. Typically, this is listed in microns. A human hair is about 100 microns in diameter. A red blood cell is about 5 microns across.
• Cleanliness– How clean the environment needs to be to produce the product.
This is often listed as Cleanroom Class.
• Form Factor– Size of the substrate or starting material used in manufacturing.
This is defined in millimeters or inches.
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 7 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Geometries- What is small?
• Why do we need a Cleanroom?
• Current products are very small
Typical Silicon Wafer -8 inch or 200 mm
Individual features are < 0.1 micron
Microprocessor Die 1 cm by 1 cm
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 8 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Geometries continue to get smaller
Source: The Nanoelectronic ChallengePeter Kucher, Fraunhofer CNT
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 9 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Nanotechnology 2003
0.09 µ CD90nm
Nm = Nanometers
4 µ CD 2.5 µ CD 1.5 µ CD
NMOS 1980 HMOS 1985 CMOS DLM 2 µ 1989 CMOS QLM 0.35µ 1995
0.35 µ CD4000nm 2500nm 1500nm 350nm
Bacteria Skin FlakeCigarette Smoke
0.2 - 0.4 µ ? 2 µ ? 8 µ ?
Amines200 – 400nm 2000nm 8000nm
~ 50 nm
Geometries- Killer defect size
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 10 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Geometries, defects, and yield
Defects (Down) Yield (Up)
LOW Defect Density HIGH Yield=
=HIGH Defect Density LOW Yield
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 11 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Fed STD209 E
Equivalent
ISO Classification number (N)
Maximum concentration limits (particles/m3 of air) for particles equal to and larger than the considered sizes shown below
0.1 µm100nm
0.2 µm 0.3 µm300nm
0.5 µm 1 µm1000 nm
5 µm
N/A ISO Class 1 10 2
N/A ISO Class 2 100 24 10 4
1 ISO Class 3 1,000 237 102 35 8
10 ISO Class 4 10,000 2,370 1,020 352 83
100 ISO Class 5 100,000 23,700 10,200 3,520 832 29
1,000 ISO Class 6 1,000,000 237,000 102,000 35,200 8,320 293
10,000 ISO Class 7 352,000 83,200 2,930
100,000 ISO Class 8 3,520,000 832,000 29,300
ISO Class 9 35,200,000 8,320,000 293,000
NOTE: Uncertainties related to the measurement process require that concentration data with no more than three significant figures be used in determining the classification level.
Cleanliness - ISO Clean Class
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 12 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
This table lists the air changes per hour necessary to achieve the cleanliness level desired. The information provided below is based on data tested by the Institute of Environmental Sciences and Technology (IEST).
Reference IEST-RP-CC012.1 – Institute of Environmental Sciences and Technology
ClassAirflow Type
Average AirflowVelocity
(Over the Entire Area)
Air ChangesPer Hour
Class 100,000ISO 8
N M .005-.041 m/sec (1-8 ft/min) 5-48
Class 10,000ISO 7
N M .051-.076 m/sec (10-15 ft/min) 60-90
Class 1,000ISO 6
N M .127-.203 m/sec (25-40 ft/min) 150-240
Class 100ISO 5
U N M .203-.406 m/sec (40-80 ft/min) 240-480
Class 10ISO 4
U .254-.457 m/sec (50-90 ft/min) 300-540
Class 1ISO 3
U .305-.457 m/sec (60-90 ft/min) 360-540
ISO 2, 1 U.305-.508 m/sec (60-100 ft/min)
360-600
1 When airflow type is listed, it represents the more common airflow characteristics for cleanrooms of that class: U = unidirectional N = nonunidirectional M= mixed.2 Average airflow velocity is the way that airflow in standard dimension cleanrooms (that is, those that typically have a ceiling height of 10 feet or 3 meters) usually is specified. This term is commonly used to refer to unidirectional airflow.3 Air changes per hour is the way that nonunidirectional and mixed airflow in nonstandard, high bay, or unusually configured cleanrooms usually is specified.
Cleanliness - Air Changes per hour
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 13 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
$/Sq Ft
Class 0.5 micron particles per
cu ft (Fed 209D)
$2,250 1 1
$1,800 10 10
$1,425 100 100
$900 1,000 1,000
$700 10,000 10,000
$75 Support
(Facilities)
N/A
Cleanliness- Why is it important?
Typical Cleanroom Cost Assumptions
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 14 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Wafer Form Factor Evolution
Wafer Form Factor
0
2
4
6
8
10
12
14
1964
1968
1972
1976
1980
1984
1988
1992
1996
2000
2004
2008
Year
Wa
fer
Dia
me
ter
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 15 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Panel Form Factor Evolution
Panel Form Factor
0
1
2
3
4
5
6
7
8
9
19
88
19
90
19
92
19
94
19
96
19
98
20
00
20
02
20
04
20
06
Year
Gla
ss G
en
era
tio
n
2200 x 2500
1870 x 2200
1500 x 1800
1100 x 1300
730 x 920
550 x 650
370 x 470
300 x 400
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 16 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Panel Form Factor EvolutionGen 8 2200 x 2500 mm
Gen 7 1870 x 2200 mm
Gen 6 1500 x 1800 mm
Gen 2 370 x 470 mm
Gen 5 1100 x 1300 mm
Gen 4 730 x 920 mm
Gen 3 550 x 650 mm
Gen 1
300 x 400 mm
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 17 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Panel Form Factor Driver – Revenue
• Gen 7 (1870 x 2200 mm) can produce – Eight 40” Diagonal LCD TVs
– or
– Six 46” Diagonal LCD TVs
• Gen 8 (2200 x 2500 mm) can produce– Eight 46” Diagonal LCD TVs
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 18 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
FPD Technology 2005 Sales 2007 Sales CAGR
a-Si TFT LCD $54.4 B $70.1 B 13%
PM LCD $6.0 B $4.5 B -14%
PDP (Plasma) $5.8 B $8.9 B 24%
LTPS TFT LCD $5.5 B $6.8 B 11%
OLED $0.5 B $1.8 B 86%
Other Tech. $2.0 B 2.0 B 0%
All FPD $74.3 B $94.1 B 13%
Size of Display Market
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 19 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
• Clothing and Wearable Displays• Foldable Displays• E Book• Electronic paper
FPD Future: Flexible Displays
Images courtesy of Seiko / E Ink, Fujitsu, and Philips.
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 20 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
• Start with small form factor• Grow to a larger form factor• Need to automate/mass produce
• Roll-to-Roll Manufacturing
Flexible Displays
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 21 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Designing the Cleanroom
• Tools or Equipment
• Utilities
• Building Cross Section
• Cleanroom Concepts
• Air Management
• Chemicals
• Other Design Considerations
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 22 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Tool Needs
• Quantity
• Utility requirements
• Cleanliness level
• Size– Footprint
– Layout
– Move-in path
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 23 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Tool Quantities
• Quantity determined via capacity model
Process Tool
Total
Required
Tools
Total
Required
Whole
Tools
Equipment
Utilization*
Laminate Mask Pattern 1.2722 2 55.6%
Laminate, Remove 1.2722 2 55.6%
Laser Repair 2.4080 3 70.2%
Laser, Pulsed Excimer 1.2722 2 55.6%
PECVD Deposit 8.3042 9 78.1%
PECVD, Microwave 2.4853 3 70.1%
PECVD, Microwave Inert 2.4853 3 70.1%
Reactive Ion Etch 5.2881 6 74.6%
Receive from evaporator 1.2722 2 55.6%
Roll Coat 8.8598 9 86.0%
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 24 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Photos Courtesy of Shibaura
Tool Footprint
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 25 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Photos Courtesy
of Entegris
Tool Footprint
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 26 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Tool Layout – What is Wrong with this Picture?
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 27 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Tool Layout - Incorrect
• Should not be in Front of Column
• No Support Space
• No Access to Rear of Tool
• No Room To Make Utility Connections
• Should Be Bulk-headed
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 28 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Tool Layout - Correct
• Table Utilizes Space in Front of Column
• Plenty of Maintenance Space
• Accessibility to Rear of the Tool
• Plenty of Room for Utility Connections
• Tool is Bulk-headed for Easy Access
• Allows space for material handling
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 29 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Tool Layout Options - Bulkheading
View of the clean bay side.
Machine interface is on the clean side, with the tool bulkheaded into
the chase.
View of the chase side.
Back of tools sit in the “dirty” environment.
Maintenance can be done in lower protocols.
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 30 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Tool Layout Options – No Bulkheading
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 31 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Tool Spacing for Material Movement
Photo Courtesy of Multilayer Coating Technologies
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 32 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Tool Spacing for Material Movement
• Typical wafer tools have an area space factor of 1.3. A typical tool has a footprint of 100 square feet. This means the tool and the area necessary to access it require 130 square feet. These tools can be placed very close together and the aisle between them can be 6 feet or less wide. This allows more than adequate room for operator and product movement.
• Continuous web processing equipment has an area space factor of 1.75. This equipment is much larger. A typical tool is 784 square feet. The access area required around the tool is also much larger. The maneuvering of the lift carts causes aisles to be 15 feet wide and 11 feet of space between tools. This means the tool and the area necessary to access it require 1,372 square feet. This space requirement can be reduced with future improvements in the lift carts.
Web Process Tools
Typical Wafer Tools
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 33 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Tool Move In
• Utilize Existing Space
– Use the service corridor as a move-in path via chases
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 34 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Utilities - Planning and Analysis
• Many individual spreadsheets and/or “home-grown” software applications exist throughout the industry.
• Each application has its own assumptions, analysis methodology, cost and process data, and “frame of reference.”
• Separate databases or spreadsheets used for different projects often contain contradictory information, resulting in confusion.
• Information is not validated by observing process tools in use.
• Accuracy of vendor data is not verifiable by Architects/Engineers who sometimes do this type of planning.
• It requires process and operations expertise to get an accurate database and “by-project” analysis.
• Data is not easily diversified for varying utility usage in phased projects.
• A detailed utility matrix is required to solve these problems.
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 35 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Utility Matrix
• What is required for a project:– Database system which quantifies, totals, and summarizes the utility
requirements for the user’s equipment.– Various utility parameters that are tabulated and quantified include:
• Liquids• Exhausts• Electrical• Process and house gases• Process supplies (other chemicals)
• Total fab requirements (by area or by fab)– Process gases, liquids, and supplies– Electrical requirements– Exhaust demand– Drain needs
• Heat load to the room– Needed for accurate HVAC sizing– Accounts for exhaust and process cooling water reductions in load.
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 36 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Facility Research
• Capacity of Systems (all upstream components) – per base build specifications
• Location – verified per base build specifications
• Termination
• Expandability
• Flexibility
• Accessibility / Mounting etc.
• Purity Verified - per base build specifications
• Quality Verified - per base build specifications
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 37 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Facility Research
• Use Flow Meters to check the flow rates of gases or liquids in the facility.
• Use the Pressure Gauge to check the pressure of the gases or liquids that are in the facility
• Use calibrated quality instruments to check particle counts and chemical analysis of incoming gases and liquids, available volumes of exhaust, static pressure, etc.
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 38 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Facility Research
• Typical view of facility area before tool hookup
• Very Narrow Chase
• Wall Mount Piping
• Shows stubs for hookup connections
• Piping Stage of Construction
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 39 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Building Cross Section
Cross Sections.
• Single Floor – Less Expensive– Slab on Grade
– Mixed with partial subfab
• Raised Floor/Subfabs- Most expensive– Is either option absolutely necessary?
• Can support areas be located elsewhere?
• Can process equipment support pieces be located in chases?
– Very Costly
– May require additional vibration isolation for sensitive equipment and process
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 40 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Slab on grade (Low Sidewall) Return
• Least expensive option because it doesn’t require a raised floor
• Least flexible because space must be left in the wall for air flow
• Higher pressure drop across smaller wall openings requires more fan energy
Chase BayBayCleanroom
Isolated Foundation
Exhaust Scrubber
Pressurized Plenum
Piped Services RecirculatingAir Handlers
Wet wastes
Chase BayBayCleanroom
Isolated Foundation
Exhaust ScrubberExhaust Scrubber
Pressurized Plenum
Pressurized Plenum
Pressurized Plenum
Piped Services RecirculatingAir Handlers
Wet wastes
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 41 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Raised Floor Return
• Require a raised access floor, with tool pedestals for vibration sensitive tools
• Very flexible because air passes below the tools, better laminarity of air flow
• Lower pressure drop across all floor area, better vertical laminar flow
• Space below floor can be used for drains and to distribute power and some gases
Chase BayBay
Cleanroom
Isolated Foundation
Exhaust Scrubber
Pressurized Plenum
Piped ServicesRecirculatingAir Handlers
Wet wastes
Chase BayBay
Cleanroom
Isolated Foundation
Exhaust ScrubberExhaust Scrubber
Pressurized Plenum
Pressurized Plenum
Pressurized Plenum
Piped ServicesRecirculatingAir Handlers
Wet wastes
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 42 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Subfab Return
Exhaust Systems
Piped ServicesPiped Services
Chase BayBayCleanroom
Sub-Fab
Interstice
20
’20
’20
’20
’
Isolated Foundation
Exhaust ScrubberExhaust Scrubber
Pressurized Plenum
Pressurized Plenum
Pressurized Plenum
Heavy StructureTarget 250 to 125 µin/s
RecirculatingAir Handlers
Wet wastesWet wastesSupport tools, gas cabs, etc.
• Air passes through the fab and down into the subfab
• Space in the subfab can be used for support equipment such as pumps and gas cabinets
• Highest cost but conserves cleanroom space
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 43 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Bay / Chase Cleanroom Concept
• Most common cleanroom layout
• Provides for maximum flexibility with least area under filter
• Allows for services and maintenance for the “back” side, or the chase
• Can bulkhead tools in the chase so that only machine interface is in the clean zone
Service
Tour Aisle
Clean Protocols
Clean Aisle
Ba
y
Chase
Tool Move In
People & Materials
Protocol Options
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 44 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Bay / Chase Air Return Options
Bay / Chase with low sidewall return
Bay / Chase with floor return
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 45 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Ballroom Cleanroom Concept
• Layout used primarily for Class 1,000 or 10,000
• Can be used with mini-environments for some processes
• People, product, and equipment share the clean zone
• Can be very flexible for tools requiring few utilities such as CDA, N2 and power
Service
Chase
Ballroom
Ch
as
e
Clean Protocols
Tool Move In
People & Materials
Protocol Options
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 46 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Ballroom Cleanroom Concept
Ballroom Layout
Class 1,000 with mini-environments
Ballroom Cleanroom
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 47 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Air Management StrategiesDucted System
• Flexible locations for filters
• Air handling equipment is located outside the clean zone
• Usually lowest operating cost of system options
• Requires most interstitial height, increases building height
Chase (Return)
HEPA Filter
Recirc
Free Air Return
Bay (Clean Aisle)
Make -up
Return Air
Minimum bend radius
Fan Deck or Support Structure
Chase (Return)
HEPA Filter
Recirc
Free Air Return
Bay (Clean Aisle)
Make -up Air
Return Air
Minimum bend radius
Fan Deck or Support Structure
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 48 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Air Management StrategiesFan Filter Units
• Flexible locations for filters, not related to wall locations
• Can have lower first cost
• Fan and filter maintenance is done inside the cleanroom
• Can fit in reduced access ceiling space
• Can be individually controlled and monitored
• If one unit malfunctions, the clean space can still operate
• Each unit can be replaced individually
• Difficulty identifying fans or filters that are out of services
• Fan noise can be a significant problem
Fan / Filter Boxes
Fan / Filter Unit
OpenPlenum
Free Air Return
Bay (Clean Aisle)
Chase (Return)
Make-up Air
Fan / Filter Boxes
Fan / Filter Unit
OpenPlenum
Free Air Return
Bay (Clean Aisle)
Chase (Return)
Make-up Air
(Conditioned)
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 49 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Air Management StrategiesPressurized Plenum
• Flexible locations for filters
• Equipment maintenance is outside the cleanroom
• Fairly low operating cost, comparable to ducted filter option
• Provides local sensible cooling to return air
• Less height required than ducted supply
• Can combine ducted and open return for more local air separation
• Walls are limited to locations of plenum boxes, (can supplement with FFUs)
• Must measure exact size for fit – field modifications costly.
Pressurized Plenum
Free Air Return
Bay (Clean Aisle)
Make-up Air
HEPA Filter
Recirc
Plenum Box
Return Air
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 50 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Automated Wet Process Manual Wet Process
Chemicals at Point-of-Use
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 51 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
CMP chemical distribution Wafer Fab
Labeled double containmentchem distribution lines- subfab
Chemical Distribution Systems
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 52 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Process Nitrogen (Process Gases): “Electronic Grade”
Subject GAS Content Method of Analysis
Nitrogen 99.999 %
O2 1 ppm Portable O2
CO2 <0.5 ppm
CO <0.5 ppm
H2 <1 ppm
H2O 1 ppm Shaw or equivalent
THC <0.5 ppm Flame Ionization GCA. GCA of Residue in activated charcoal filter that was on the line for 1 hour at approximately 1 LPM flow rate.
ACCEPTABLE NUMBER OF PARTICLES/CFM
Particle size [um] Allowable Quantity
0.1 – 0.3 <05
0.3 – 0.5 <03
0.5 – 1.0 <00
> 1.0 <00
Note: “VSLI” Grade is usually half of these levels.
Other Design Considerations - Gases
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 53 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
House Nitrogen “Carrier Grade”
Subject GAS Content Method of Analysis
Nitrogen 99.999 %
O2 2 ppm Portable O2
CO2 < 1 ppm
CO < 2 ppm
H2 < 2 ppm
H2O 1 ppm Shaw or equivalent
THC (C1-C5) < 1 ppm Flame Ionization GCA
THC <0.5 ppm GCA of Residue in activated charcoal filter that was on the line for 1 hour at approximately 1 LPM flow rate.
ACCEPTABLE NUMBER OF PARTICLES/CFM
Particle size [um] Allowable Quantity
0.1 – 0.3 <10
0.3 – 0.5 <07
0.5 – 1.0 <04
> 1.0 <01
Other Design Considerations - Gases
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 54 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
DI Water (Liquids in contact with materials)Particle and Contaminant Specs
Deionized Water: Typical quality at point of use to process equipment in a class 100 cleanroom.
Resistivity 18.0 Meg Ohms
TOC less than 50 ppb (Total Organic Carbon)
Residue less than 50 ppb
Bacteria less than 10 per 100ml after 72 hours
Soluble Silica less than 10 ppb
Particles less than 20 per liter at 0.5 micron or less
Sodium less than 0.2 ppb
Potassium less than 0.3 ppb
Chloride less than 0.2 ppb
Bromide less than 0.1 ppb
Nitrate less than 0.1 ppb
Sulfate less than 0.3 ppb
Copper less than 2.0 micrograms per liter
•5 ft/second recirculation flow rate prevents bacteria growth in water.
Other Design Considerations – DI Water
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 55 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Cleanliness of Pipe
• Carrier of process gases and fluids– 316 electropolished stainless steel, 316 L electropolished, 304
Stainless or Type L copper – gases.
– PVDF (teflon), polypropylene, or PVC – DI water/chemicals
• Filtration and purification, sterilization – all add cost
• How clean is the plumbing of your process equipment?– Wet hoods
– Wet processors
– Gas manifolds
– These are nearest to the point-of-use
Other Design Considerations - Piping
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 56 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
• In addition to particle counts, other Room Conditions are also critical
– ESD control
– Temperature
– Humidity
• Cleanliness at the substrate surface during process is critical and may not depend on room abatement.
– Clean process tools/equipment
– Minienvironments- localized fan powered HEPAs, with or without temperature/RH control and robotics.
Other Design Considerations- Environment
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 57 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Other Design Considerations - Facility Conditions
• Building– Site plan, available square footage
– Available Square Footage for each intended use
– Area available for support, air handling and utilities
– Available height for cleanroom envelope
• Vibration Issues– Sources such as HVAC equipment, traffic, trains, implanter wheels
– Areas with critical vibration requirements – metrology, lithography, and SEM
– Techniques for abatement
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 58 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Other Design Considerations - Facility Conditions
• Electromagnetic Interference and ESD– Sources such as Overhead or underground power lines,
transformers, Light rail systems, bus and truck traffic, heavy doors
– Tools and areas with critical EMI requirements- SEM
– Electrostatic discharge- can attract particles
– Abatement techniques
• “House” Utilities: Clean Dry Air, Nitrogen, DI water– Quality of these also determines process environment
– Particle count/size
– Contaminates
– Dew point of Air
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 59 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Other Design Considerations - People Issues
• Number of people working in each area
• Gowning
• Viewing
• Communication
• Supervision
• Maintenance Access
• Security
• Lighting
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 60 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Other Design Considerations - Material Handling, Storage of Supplies, Equipment Needs
• Product – within the tool, intrabay, interbay, stockers, MGV, AGV, monorail options
• WIP philosophy-experiment storage
• Standard Mechanical interfaces (SMIF)
• Production Supplies- Maintenance supplies/parts
• Garments and gowning protocol
• Record keeping methods– Notebooks and Pens, Computers
– Documentation- electronic or paper formats
– WIP tracking System – location of terminals
• Tools and toolboxes
• Equipment Staging
• Wipe down areas
• Pump rebuild areas
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 61 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Summary
Major steps for designing a cleanroom include determining-
• The product you will make
• The geometries required
• The form factor you will use
• The cleanliness levels needed
• The tool set to support your demand
• The utilities needs (utility matrix)
• The building cross section
• Air management strategy
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 62 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Summary
• Clean Class
– Class 10; 100; 1,000; 10,000; 100,000
– Most Costly Decision
• Impacts
– Air Changes and Treatment
– Quantity Filters
– Quality of Filters (ULPA vs. HEPA)
– Types of Construction Materials
– Cost of Ownership
– Understanding the Process and Geometries will help in selecting the appropriate clean class
– Providing the right combination of clean class by area can satisfy user needs and reduce costs.
Photo BayClass 100
Thin FilmsClass 1,000
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 63 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Remember to keep the Utility Matrix a Living Document
• The utility matrix you’ve created must continue to be a living document throughout the life of your factory
– Otherwise, you’ve created a utilities snapshot that was outdated almost as soon as you last saved the file on your hard drive
• The benefits of continuing to review and update your utility matrix: You’ve created a database that future process and equipment engineers can use to more accurately design utilities for future fabs
– You can evaluate opportunities for future cost savings based on utility usage (real time data loaded directly into utility matrix database)
AIM
CA
L.o
rg
AGI Abbie Gregg, Inc. | Designing a Cleanroom to Accommodate Roll to Roll Processing Equipment Slide 64 of 65
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
ACKNOWLEDGEMENTS
The author would like to thank the following:
• AIMCAL for the opportunity to make this presentation
• The staff at AGI for their assistance in assembling this document
• You, the audience, for your attention
AIM
CA
L.o
rg
Presentations\Tradeshow & Conference Presentations\AIMCAL Fall Technical Conf - Oct 2007\Mark Strnad - Designing CR to Accommodate R2R Process Equip Final.ppt
Thank You!
Designing a Cleanroom to Accommodate Roll- to-Roll Processing Equipment
Presented by:
Mark StrnadVice President Operations and Engineering
October 7-10, 2007Radisson Fort McDowell ResortScottsdale, Arizona USA
AIM
CA
L.o
rg