ofna ultra lx comp manual - competitionx.com · 36730 cap joint 94036 5x5mm set screw 30630...

INSTRUCTION MANUAL

Ultra LX Comp Rev:02

REQUIRED FOR OPERATION

THINGS NEEDED

AA Batteries ( 12 pcs )

Glow Fuel20%

TOOLS NOT INCLUDED IN KIT,BUT NEEDED TO MAINTAIN YOUR CAR.

Phillips Type Screw Drivers ( L )

Phillips Type Screw Drivers ( S )

Needle Nose Pliers

Cutter

91009Curved Scissors$5.95

Knife

10239Instant Cement

Cross Wrench#17109 $3.95#10796 $3.95

Glow Plug & 17MM Cross Wrench#10801 $6.95

10620Diff GearGrease$9.95

You need to get batteries for the radio transmitter and the car receiver packs.• Radio TX needs (8) eight AA batteries.• Car needs (4) four AA Ni-cad batteries, Alkaline type batteries will work, but braking will be reduced. The best is to use a 5 cell hump pack for increased voltage..

Recommended Option:You may want to upgrade the car battery pack to a Ni-Cad or NiHm 5 cell type(600AE). This will give more run time. OFNA #10212

You will need to buy a few items to start the engine and run the car.• Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will over heat engine.

• Buy LONG glow plugs, like OFNA/PICCO Plug (#51007-cool or 51008-med). Use plugs without idle bar. Do NOT use plugs, like the MC-59 or OS-8 or any short plug

In your box you will find..• #10163 - Bottle, spout top• #10219 - Red “D” size glow heater

#10212 NiHm Hump Pack,see charger 10214.

10214Over-niteCharger

MUST READ THIS BEFORE RUNNING

Running a nitro kit is fun and easy, but to make this a safe rusting.• Clean oil and dirt from chassis with a degreaser.and good experience you must observe a few rules. This

kit is extremely fast, easily over 40MPH, and can seriously Precautions

injure someone if you are not careful. • This kit is not a toy. Always run car with a second

person as a spotter and pitman.Where to run car?• Any running area you choose must be dry. Do not run

• Hot Parts - The pipe, manifold, engine and head are very car near any water or wet dirt.

hot and will cause burns.• Do not run on public streets. It is very easy to have the

car run over or damaged by hitting the curb. • Rotating Parts - Keep hands away from the drive train, • Do not operate car in tight confined places. The car is

wheels, and engine when engine is running.very fast and will easily hit something.• Do not run near people or animals. • Radio - Check batteries life before running the car. If

radio does not have full control of the car with steering • Due noise, you will want to consider the surrounding

and/or throttle/brake do not run until corrected. Failure to area when operating the car.

correct this will result in possible injury and damage to the • Do not operate the car at night. You will not be able to

car or property.drive it without hitting something.• Do not operate the car indoors. Engine exhaust is not

• Glow fuel - Do leave the glow fuel unattended with the lid healthy.

off. Fuel contains Methanol and Nitro Methane and is

flammable and poisonous.Glow Fuel• Glow fuel is poisonous!

Store fuel in cool ventilated location. Refer the glow fuel • Glow fuel is flammable!• Do not leave in fuel bottle with lid off at any time. label for additional precautions.• Do not use any fuel other than glow fuel in this engine.

• Car Fuel tank - Never store fuel in car tank, it will ruin the First Time Starting the Engine engine if left in tank.Caution! When starting engine make sure the following is

observed. • Always turn off the car BEFORE turning off radio.• Set engine Master needle to 3 turns (rich setting)• Do not do this alone, get an experienced friend to help at • DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY

first. ISSUE.• Fill fuel tank, try not to spill fuel. Do not spill fuel on

receiver IF YOU DO NOT BREAK-IN ENGINE • Hold car off the ground, so it will not runaway when first

CORRECTLY, MAINLY AT LOW RPM, starts• Turn on Radio and check the linkage before starting YOU WILL BREAK THE CONNECTING engine.

ROD!• Turn on car receiver battery switch.• Always have an air filter on the carburetor to keep dirt

out. FAILURE TO NOT READ AND Engine Break-in

FOLLOW BREAK-IN ENGINE • See Engine Page.

Emergency Stopping Engine When Running INSTRUCTIONS WILL VOID • Remove air filter and cover carb. intake.• Squeeze fuel line and hold until engine stops. WARRANTY!• With a rag, cover exhaust outlet.

Storing Car After RunningCHECK RADIO SETTING AND • Remove fuel from tank and fuel lines

• Turn off radio in carLINKAGE BEFORE STARTING• Put a few drops of after run in engine to keep it from

The car is very fast

and will too easily hit someone.

AB

C

CHECKING ENGINE THROTTLE

* Insert into transmitter.

1. Insert AA batteries into transmitter (8 Pcs).2.Turn on transmitter.3.Turn on receiver.4.Center throttle trims as shown .

A B C

1. Pull Full Throttle. 1. Push trigger to full brake position.2. Adjust alum. Stopper to increase or decrease the brake.

Idle Position (A)

Brake (C)

Full Throttle (B)

* Align throttle servo same as shown.

ASSEMBLY OF THE THROTTLE LINKAGE SYSTEM

3X3mmSet Screw

3X3mmSet Screw

3X3mmSet Screw

Plastic Collar

* Take the plastic collar from brake system plastic parts.

Throttle Spring

#10300Alum.Stopper

#10300Alum.Stopper

* Snap On.

#30530Plastic ThrottleBall Joint

2mm Rod

Fuel Tube ( 6mm )

Idle Position

Brake

Full Throttle

* Align throttle servo same as shown.

A

B

C

• Full brake arm position. Spring compresses forward and brake rods pull brake levers.

• Full throttle arm position. Spring rod pulls throttle barrel open and brake rods release pressure on brake cams.

IMPORTANTCHECK RADIO THROTTLE AND STEERING SWITCHES BEFORE RUNNING CAR

#30800Plastic Throttlekit

Note: Battery life is short when using Alkaline batteries. For safety, we recommend using Alkaline batteries for only 30 minutes before testing; mostly changing. Battery strength affects braking power and radio range. If voltage drops while running the car, you will loose control and destroy your car! This is NOT covered under warranty.

To increase run time, upgrade receiver battery to a 5-cell hump pack. Also, install a battery fail safe (OFNA # 91002) to further protect your car. But, the most important step you can make, “is to always use fully charged or fresh batteries when running your car”.

Radio shown, may be different from what is in your kit. OFNA reserves the right to change upon stock availability.

* Put the differential gears same as picture shown.

30901Cap Joint

30620x19x6mmBall bearings

30751(Fro nt/Rear)30761(Center)Diff. Case

30779P5O-Ring

307792x12.8

307792x12.8

30779P5O-Ring

30751(Front/Rear)30761(Center)Diff. Case

94034Set Screw

307790.5x26mmO-Ring

*Apply diff. Gear grease to the differential, during assembly.*Fill the dif. Case to approx 80% with grease

30901Cap Joint

30769Diff. Gear(Large)


307794x10mmWasher

307794x10mmWasher

307794x10mmWasher

307794x10mmWasher

307734mmCross Pin

307734mmCross Pin

30769Diff. Gear(Small)




307734x27mmCross Pin X2

307792x12.8mm X2

307794x10mm Washer X4

30779P5 O-Ring X2

94034Set Screw X2

*Notice the straight holes are for the front and rear only.

ASSEMBLY OF THE FRONT AND REAR DIFFERENTIAL

*Builds two differentials for font and rear.

94004 3X12mm Hex Screw

940043X12mmHex Screw X4

Step 1

Step 2

ASSEMBLY OF THE DIFFERENTIAL GEAR


30911Break Cap Joint



30761(center)30751(F/R)Diff. Case

307792x12.8


307792x12.8

30779P5O-Ring

30761(Center)30751(F/R)Diff. Case

94034Set Screw

307790.5x26mmO-RingO«¬Àô

*Notice the tapered holes are for the center differential only.


30911Break Cap Joint

30779P5O-Ring

ASSEMBLY OF THE CENTER DIFFERENTIAL

307734x27mmCross Pin X2

307792x12.8mm X2

307794x10mm Washer X4

30779P5 O-Ring X2

94034Set Screw X1

* Put the differential gears same as picture shown.

*Apply diff. Gear grease to the differential, during assembly.*Fill the dif. Case to approx 80% with grease

307794x10mmWasher

307794x10mmWasher

307794x10mmWasher

307794x10mmWasher

307734mmCross Pin

307734mmCross Pin





940043X12mmHex Screw


X4

ASSEMBLY OF THE DIFFERENTIAL GEAR

Step 1

Step 2

*Notice the tapered holes are for the center diff. Only.

35313Nylon Nut

3104051T Spur Gear

301113x10mmFlat Head Hex Screw

30201Center Diff. Mount(Front)

30201Center Diff. Mount(Rear)

35313M3 Nylon Nut

X4

X4

X4


Center differential assembly

ASSEMBLY OF THE SPUR GEAR

94033M3x3Set Screw

30171Brake Lever

30213Brake Cam

ASSEMBLY OF THE BRAKE CAM

94033M3x3 Set Screw

* The picture show are center differential after assembly.

Notethe holes for the rear diff. Mount are width

* Note:the holes for the reardiff. Mount are closer .together


940053X15mmScrew

36660Brake Pad

36661Brake Pad Linings

36650Brake DiskSteel

36650Brake DiskSteel

0.5mm*Leave a 0.5mm space between brake disk and brake pad.

30211Plastic Bushing30212Ball Bearing

30213Brake Cam

30652Center Diff.Plate


302115x8x2.5mm Plastic Bushing

94033M3x3 Set Screw

X2

X2

940053X15mm Hex Screw

X4


X4

94033M3x3Set Screw

30171Brake Lever

* Remove the double-side tape before assembly.

ASSEMBLY OF THE BRAKE CAM AND BRAKE PADS

*Leave 3mm gap between the brake cam and nut.

3mm

Note:

ASSEMBLY OF THE BRAKE CAM AND CENTER PLATE

ASSEMBLY OF THE BRAKE PADS

30211Plastic Bushing30212Ball Bearing

301213x4x4mmChromed Tube

301213x5mmHex Screw

30120Bevel Gear(Large / Metal)

*Push 3mm tubes into the holes of the diff. Case.

36730Cap Joint

940365x5mmSet screw

306306x13x5mmBall Bearing

30010Gear Box


30130Bevel Gear(Small)

34021Front Upper ArmHolder

940104x12mmHex Screw

X4301213x5mm Hex Screw

301214x3x3mmChromed Tube

X4

94036M5x5 Set Screw

X1

X2940104x12mmHex Screw

ASSEMBLY OF THE FRONT BEVEL GEARS

ASSEMBLY OF THE FRONT GEAR BOX

940294x25mm Flat Head Hex Screw





X2

X2

940294x25mmTP Flat Head Hex Screw X2

Step 2

Step 3

Step 4

Step 1


X1



X2

X2900183X25mmCap Screw 90018

3X25mmCap Screw

30160Front LowerArm Holder


30102Front bodyPost36610

Shock SupportSteel34018

Shock Tower

* Notice the direction.

* Builds two differential for front and rear.

30010Gear BoxFront Cover

* Place 5x5mmset screw in d cut.

36507Shock SupportAlum

4010410mm Ball and Socket

4010410mm Ball and Socket

368605x35mmTurnbuckle

368605x35mm

90026Set Screw

360552.5x16.8mmPin


36054Wheel Hub

360538x16x5mmBallbearings

360538x16x5mmBallbearings


34022CVA Joint

X2

X2

40102FrontLower Arm-R

40102Front Lower Arm-L

900265x5mm Set Screw

360552.5x16.8mm Pin

ASSEMBLY OF THE FRONT UPPER ARMS

40101Front UpperArm Ball End

40101Front UpperArm Ball End

40101Front UpperArm (Right)

40101Front UpperArm (Left)

* Leave 6mm .

Assembly of the right and left hand sideare the same.

* "L" mark are for left side.

ASSEMBLY OF THE FRONT KNUCKLE ARMS

40103Front Knuckle Arm(Right)

40103Front Knuckle Arm(Left)

ASSEMBLY OF THE FRONT LOWER ARMS



4010410mmSteering Ball

4010410mmSteering Ball

Note:


34024CVA Axle

34023CVA Bone

900202.5mmE-Ring

900202.5mmE-Ring

301514mm Arm Shaft

401044x16mmCap Screw


X2X230151

4mm Arm Shaft401044x16mm Cap Screw

900213mm E-Ring

X4301523mm Arm Shaft

X2

900202.5mm E-Ring

X4

* Insert the rear drive shaft into cap joint before assembly the rear lower arm.

900213mmE-Ring

900213mmE-Ring


30152Upper Arm Shaft

ASSEMBLY OF THE FRONT ARMS

40102Front Lower Arm

D

C

B

A

D

C

B

A

3x8mmHex Screw

X2

X23x8x0.8mm Washer

3x8mm Hex Screw

40029StabilizerBall End

3x8x0.8mmWasher

30341Stabilizer Ball

304036mm Ball


94035M3x8mmSet Screw

940063x18mm Hex Screw

M3x8mm Set Screw

X2

X2


A

B

94033M3x3 Set Screw

X2

94033M3x3Set Screw

* Cut the plastic as shown.

40101Caster Adjuster(in Arm Parts Bag)

* Change the caster angle by moving the caster adjuster in different place..

CLIP THE CASTER ADJUSTER IN FRONT UPPER ARM



ASSEMBLY OF THE FRONT STABILIZER

34027StabilizerKit

Note:

940223x18mm Flat Head Hex Screw X2


940294x25mm Flat Head Hex Screw X2


X2

X2

X1


940274x16mmFlat Head HexScrew



Set triangle marks inthe direction shownin Fig.(1)

36730Cap Joint

900265x5mmSet screw

X15x5mmSet screw


30010Gear Box


30130Bevel Gear(Small)

Step 2

Step 1

900183X25mmCap Screw


30010Gear BoxFront Cover

36610Shock SupportSteel

30351Toe-in Cams

30351Rear Lower Arm Holder

ASSEMBLY OF THE REAR GEAR BOX

ASSEMBLY OF THE REAR SHOCK TOWER

34033Rear Body Post

34019Shock Tower

1 Degree

1.5Degree

Fig.1

Use rear tor-in adjustere.

* place 5X4 mmset screw in D cut

301514mm Arm Shaft

34028RearDriver Shaft

900213.0mmE-Ring

2.5mm E-Ring

900202.5mm E-Ring

900213.0mmE-Ring

40102Rear Lower Arm

3mmPlastic Washer

3mmPlastic Washer

361703mm Arm Shaft

36081WheelRear Hub

360538x16x5mmBall Bearings

360538x16x5mmBall Bearings

900265X4mmSet Screw

*Do not tighten set screw over tighten.

X4900213.0mm E-Ring

X4900202.5mm E-Ring E«¬¦©Àô

368507mm Ball

368507mm Ball


35313Nylon Nut

X2900265x5mm Set screw

94035M3x8mm Set Screw X2

94033M3x3 Set Screw X2

940063X18mm Hex Screw x2


35313M3 Nylon Nut X2

35313Nylon Nut

40065Upper armPlastic Rod End

40065Upper armPlastic Rod End

360552.5x16.8mmPin

36082Rear Wheel Axle Shaft

26mm

ASSEMBLY OF THE REAR WHEEL HUB ASSEMBLY OF THE UPPER ARM ROD*Builds two rear wheel hubs for use. * Builds two upper arms for left

and right hand-side.

* Anticlockwise mark.

X2



ASSEMBLY OF THE REAR LOW ARMS INTO GEAR BOX

0 10 20 30 40 50

mm

Assembly of the right and left hand side are the same.


* Insert the rear drive shaft before assembly the rear lower arm.

36054WheelHub (8mm)

90020



x2

35313M3 Nylon Nut x2

X2

30270Wing Mount(Left) Kit

30270Wing Mount(Right) Kit

102903mm Alum.Washer

102903mm Alum.Washer

102903mm Alum. Washer x6

94022M3x18mmFlat HeadHex Screw

94022M3x18mmFlat Head Hex Screw



30270Wing StayPost(Plastic)

35313M3 Nylon Nut

940114X16mmHex Screw X2


900193X25mmCap Screw x2

1. (High Position) 2. (Low Position) 3. (Bigger Angle)

* The installing angle becomes bigger in order 1 to 3.

3x8x0.8mm Washer x2

3x8mm Hex Screw x2

3x18mmWasher

3x8mmHex Screw

3x8x0.8mmWasher

M3x3Set Screw


30340Stabilizer Ball

304016mm Ball


94035M3x8mmSet Screw

ASSEMBLY OF THE REAR STABILIZER

ASSEMBLY OF THE STABILIZER ROD

30340Stabilizer

A B

* Cut the plastic as shown.


Stabilizer RodAssembly

30271Wing HolderAssembly

ASSEMBLY OF THE WING STAY



x2940063x18mm Hex Screw

94003M3x10mmHex Screw

30540Front Plate

30380Servo SaverPost

34014Front Stiffener


35318M3 Nylon Nut

x2

94005M3x16mm Hex Screw


940053X15mm Screw

x2

x3

x2


36742Servo SaverBushing

36750Servo Saver Connevtor 35313

3mmNylon Lock Nut

353133mmNylon Lock Nut

367436mm E-Ring x4

36740Servo SaverTop Adapter

367466mmE-Ring

36740Servo SaverHorn B

36740Plastic Tube

36740Saver SaverShaft (Brass)

367436mmE-Ring

367436mmE-Ring

367436mmE-Ring

36740Saver SaverShaft (Brass)

367418x12mmWasher

36741Servo SaverSpring

36740Servo SaverHom A

36740Servo SaverHom A

367007mm SteeringBall End

368507mm

368507mm

367007mm SteeringBall End


36.5mm

*Made two steering rods for left and right hand-side.

0 10 20 30 40 50

mm

ASSEMBLY OF THE SERVO SAVER

ASSEMBLY OF THE STEERING TIE-ROD

400393mm Tapered Washer




36740Servo Saver"A" and" B" Plastic Set

30240Front Bumper

940274x16mmFlat HeadHex Screw





36100Center DriveShaft(Front)



x8


x2



x2

x2

*Insert drive shaft into cap joint

A

A

Center Diff.Assembly

* Insert the front bumper before assembly.

ASSEMBLY OF THE GEAR BOX ONTO CHASSIS

34016Chassis

36100Center DriveShaft (Rear)




34080Stone Guard

34080Stone Guide



X4


X2


X6940193x10mmFlat HeadHex Screw





*Insert drive shaft into cap joint before assembly.

ASSEMBLY OF THEREAR BOX ONTO CHASSIS

ASSEMBLY OF THE STONE GUARD

34041Chassis


X12


34025Radio Tray





94005M3x16mm Hex Screw

X2

Steering Servo

Throttle Servo





X4




34013Receiver Box




2X15mmHex Screw

2X15mmHex Screw

2X15mmHex Screw

X2

10280Switch Cover

Switch

Receiver

Battery

34026Servo Washer

34026Servo Washer

34026Servo Mount

34026Servo Washer

34012Radio TrayAlum, Post

34020Servo Mount

Put the receiver andbattery into receiverbox.

34013Receiver BoxCover

Front Steering Servo

34015SensorSupport

ASSEMBLY OF THE FRONT SERVO AND RADIO TRAY

* Put the servo wire into receiver box and connect to receiver.

* Connect battery case wire to switch.

* Connect the switch wire to receiver.

*Put the protection rubber onto your servo.

Note:

34070Rear Stiffener

30287Fuel TankPlastic Post

30287Fuel TankPlastic Post

Pressure Nipple

X7940193x10mmFlat Head HexScrew



X4






94004X12mmHex Screw


X2

40109Fuel Tank

40109Fuel Tank

Pressure Nipple

ASSEMBLY OF THE RADIO TRAY ONTO CHASSIS

30280Turnbuckle

3X12mmHex Screw

Use the screw provided withyour servo.



10711Servo Horn

373706mm Ball & Socket

373706mm Ball & Socket

3X12mmHex Screw10711

Servo HornAdapter

X23X12mmHex Screw

5X12mmHex Screw

4x12mmFlat Head Screw

X1


40199Plastic BallEnd

40199Plastic BallEnd

ASSEMBLY OF THE ENGINE ONTO CHASSIS

ASSEMBLY OF THE FRONT STEERING ROD

35314M3 Nylon Nut

X1

3mmWasher

353143mmNylon Nut

31990Muffler Assembly

À@«¬®M

103307mmTapper Corn

Step1 Step2

Step 6

Step 5

Fit the flywheel usinga pair of the plIer andcross wrench.

100403 PinFlywheel 10098

SG Clutch Nut

Place the clutch shoes withthe clutch springs over the3 pins of the flywheel.Using a phillips screw driveror needle nose pliers andbend the small end lf theclutch spring behind thepilot shaft #174D or #180Dthan press down.

10100Clutch Spring

10010Clutch Shoes

100995x9x0.3mmWasher

341105x10x4mmBallbearing

Step3

341105x10x4mmBallbearing

10400Clutch Bell

100995x9x0.3mmWasher


10060Manifold

10068Manifold Adapter

31990Tuned Pipe

10180Silicone Tube

10182Nylon Straps(Middle)

35313M3 Nylon Nut

X4

3x20mm Cap Screw

100993x10mm Cap Screw

X1

X4

ASSEMBLY OF THE CLUTCH

* Only use this 6.3mm tapered cone for threaded crank shaft with drive nut.

SG TypeCrank Shaft

10091Pilot Shaft

103306.3mmTapper Cone

Threaded CrankShaft

30480Engine Mount

30481Mounting Hardware

Step4

SG¶b¤¤¤ßÁ³U


*Put the nylon nut into the groove of the engine mount.

10120Manifold Spring

10100Clutch Spring

35313M3 Nylon Nut

Step 2

Step 1

Step 4

Step3308002X4mmHex Screw

308002X4mmHex Screw

308002X8mmHex Screw2X7x0.5mm

Washer

308002X7x0.5mmWasher

308002mmTie-RodEnd

308002mmTie-RodEnd

30800AdjustMount

308002mmAdjust Mount

940333x3mmSet Screw

30800ServoMount

10768Servo Hom

308002X65mmRod


308002X65mmRod

308002mmNut

10769Servo HornAdapter

940333x3mmSet Screw

30800

AlumStopper


940333x3mmSet Screw

30800

AlumStopper

308002X65mmRod

30800ThrottleSpring

USING BREAK ADJUST NUT

3X8mmHex Screw

940333x3mmSet Screw 30800

AlumStopper

30800Antenna Pipe

94033x3mmSet Screw

30800AlumStopper

Snap On.

30800

ThrottleBall End

Loose

TightenMore Brake Less Brake

Tighten or loose theadjuster nut will change the brake.

3x10mmTapping Screw

10017Air FilterCap

10016Air FilterSpongeRefill

10021Air FilterConnector

10020Nylon Strap(Small)

Apply filter oil to the sponge before use.

X22X4mmHex Screw

X22X8mmHex Screw

94033M3x3Set Screw

X3

X22X10mmHex Screw

ASSEMBLY OF THE THROTTLE LINKAGE

M2 Nut X2

30800Throttle Slider

400907mmR-Ring

400907mmR-Ring

400902mmWasher

400902mmWasher

400901mmWasher

400901mmWasher

400903.5mmO-Ring

400903.5mmO-Ring

400903.5mmO-Ring

400903.5mmO-Ring

40076(Front)Shock body

40077(Rear)Shock body

4005914.7mmO-Ring

49041Spring Adjuster

400602.5mmNylon Nut

400602.5mmNylon Nut

2.6x5mmWasher

2.6x5mmWasher

32235Shock Piston

32235Shock Piston

40093Shock Cap

32033Pressure Top

UP

Down

Move slowly.

304116mmBall

40058Shock ShaftDust Cover

* Push 6mm ball joint into ball end.

40069Shock Spring(Black)

40063Spring Holder

ASSEMBLY OF THE SHOCK Fit the o-ring into groove.

( Make 2 for rear. )

( Make 2 for front.)

* Be careful not to damage shock shaft.

40059Oil Seal

40059Oil Seal

J-47Shock PlasticRod End

40056Shock PlasticRod End

1. Pull down piston and pour oil into shock cylinder.

FILL THE SHOCKS WITH OIL

2.To remove air bubbles by slowly moving piston up and down.

3. Pull down piston, attach pressure top and shock oil overflow with tissue paper.

*Fit into the groove.

ASSEMBLY THE DUST COVER AND SHOCK SPRING

40055 Short Shaft

* Long shaft for rear.

* Short shaft for front.

40054 Short Shaft

*40058Cut 6mm for front.

49041

353133mmNylon Nut

40056Plasticbushing

* Take the plastic bushing from the shock plastic parts tree.

3x20mmCap Screw

ASSEMBLY OF THE FRONT AND REAR SHOCK ABSORBER

353133mmNylon Nut

40056Plasticbushing

3x20mmCap Screw

35313M3 Nylon Nut

X4

X43X20mmCap Screw

Assembly of the right and left hand side are the same.Assembly of the right and left hand side are the same.


ASSEMBLY OF THE TIRES AND WHEELS(Right)

ASSEMBLY OF THE TIRES AND WHEELS(Left)

86082Comic Tires

86082Bones Tires

81092Inner sponge

Inner sponge

86034Wheel(Right)

86034Wheel(Right)

Apply instant glue intothe groove of the wheel.

Apply instant glue intothe groove of the wheel.

40083Wing

Plastic Washer

14150Body Clips

Drill two 7mm holesfor mounting.

0 5 10 15 20 25510152025

Check the hole spacing on the underside.

Tire and Wheelassembly.

15072BlueWheel Nut

15072BlueWheel Nut

15072BlueWheel Nut

15072BlueWheel Nut




ASSEMBLY OF THE TIRE ONTO FRONTKNUCKLE AND REAR HUB

ASSEMBLY OF THE WING

* Notice the direction of the tires.




SETTING GUIDE

FRONT CAMBER ANGLE SETTING REAR CAMBER ANGLE SETTING

Place the model car on flat surface. Raise the chassis to it's maximum clearancebefore the wheels leave the ground.Adjust the length of the front and rear upper arms so that the wheels are right angle to theground.The camber angle adjustment can be moving the turnbuckle rod on the upper arms, clockwise or anticlock.(We suggest use zero degree for the front and one degree for the rear.) negative

- -- -+ ++ +

TurnbuckleTurnbuckle

FRONT TOE-IN AND TOE-OUT SETTING

TOE-IN

TOE-OUT TOE-OUT

NEUTRAL POSITION

Adjust the length of front steering rod to change thetoe angle.

Making the tie rod longer will make the front tires become toe-in.Response will be slower and will over steer.

Making the tie rod shorter will make the front tires become toe-out.Response will be quicker and will under steer.

REAR SHOCK ANGLE SETTING

12 3

1 2 3

Firm rear suspension, over steering.Soft rear suspension, under steering.

Steering Rod

Soft Firm

Soft Firm

FRONT SHOCK ANGLE SETTING

1 2

1 2

Firm front suspension, less steering.Soft front suspension, more steering.

Soft Firm

Soft Firm

3 X 8mm Washer

3mm Nylon Locknut

3 x 5mm Screw

3 x 20mm Cap Screw

* Place the clutch shoes with the clutch springs over the 3 pins of the flywheel. Using a screw driver as a lever, bend the small end of the clutch spring behind the clutch nut and press down to snap shoe in place.

* Fit the flywheel using a crosswrench or deep socket.

If engine turns when tightening,hold piston with large thick tie-wrapsand hard wood in exhaust port. Do not use metal, it will damage engine.

#10098SG Nut & Shim KiT

ASSEMBLY OF THE CLUTCH INTO ENGINE

3 x 10mmTapping Screw

#10016Air FilterSpongeRefills

#10017 - Blue#10018 - Yellow#10019 - RoseFoam Air filters Unit

#10014 - Mount Wire

#10021 - Black#10027 - Yellow#10028 - Pink#10029 - BlueAir Filter Connector Nylon Strap

( Small )

Nylon Strap ( Small )

You must oil foam filter before use.Filter will not work if not oiled.

Clean with soap and water only.You will damage foam if washedif fuel!

ASSEMBLY OF THE AIR FILTER

#10102Clutch Spring

#10010Clutch ShoesBlack Type

* Shoes are trailing.

3 x 8mmWasherMisc. Hardware#10099

#341105x10x4mmBall Bearing

#341105x10x4mmBall Bearing

#10040 (stock)3 PinFlywheel, Taper#100433 PinFlywheel, Fan

#10091Clutch Nutscrew type

3 x 5mmScrew

#10330Brass, Corn(large hole)

#10329Brass, Corn(sml hole)

304813 x 20mmHex Screw



#30480Engine Mount

#10398 - 12T#10399 - 13T#10400 - 14T (stock)#10401 - 15T#10402 - 16T#10403 - 17T#10404 - 18TClutch Bells

SEE NOTESABOVE

Notes:Non-Pull Start Engines...• Alum. Washer behind the flywheel is not needed when using Force engines or similar types. O.S. Engines will require washer spacer.

• To check!..place the brass corn against the engine bearing, then flywheel. You should be covering one or two thread of the engine shaft. If this is the case, you do not need an additional washer behind the flywheel.

You must cut the engine shaft if too long. Count 6 threads in front of the flywheel and mark. This is all you need to tighten the clutch nut and mount the flywheel.

Force Pull Start Engine w/threaded shalf...• Force Pull Start Engines required NO spacer and no shaft cutting. The engines comes with an alum cast driver washer, you use this part as the spacer, not the alum. washer shown. Also, use the special flywheel brass corn. This corn fits the thread shaft diameter so you can tighten the flywheel against the drive hub.

NoteSG Shaft

ThreadedShaft

Options

Clutch Spring10100 - Springs, Polished, Med.10101 - Spring, Gray, Hard10102 - Spring, Black, Stock

Clutch Shoes, 3 shoe clutch10010 - Shoes, Carbon Material, Black10011 - Shoes, Alum. CNC Blue, Lite Weight10012 - Shoe, Alum. CNC Purple, Med. Weight

Option10799Flywheel Wrench

ALIGN THROTTLE SERVO AND BRAKE SAME AS SHOWN

Brake is not on

Engine at idle

( Neutral Position )

Brake is on

Brake Adjust Nut

( Braking Position )

Brake is not on

Engine at full throttle

( Full Throttle Position )Less Brake

More Brake

TightenLoose

* Tighten or loose the adjuster nut will change the brake.

ULTRA LX COMP RTR PARTS10010 SHOES, 3 SHOE TYPE, CARBON BLACK, 3 PCS. 12.9510011 SHOES, 3 SHOE TYPE, ALUM. CNC BLUE, LITE WEIGHT, 3 PCS. 24.9510012 SHOES, 3 SHOE TYPE, ALUM. CNC PURPLE, MED. WEIGHT, 3 PCS. 24.9510014 MOUNT WIRE, AIR FILTER, ULTRA'S 3.9510015 OIL, FOAM AIR FILTER, 30cc 2.9510016 FOAM, REPLACEMENTS, 2 PCS. 5.9510017 AIR FILTER, FOAM, BLUE 5.9510018 AIR FILTER, FOAM, NEON YELLOW 5.9510019 AIR FILTER, FOAM, NEON PINK 5.9510020 1:8 BLK, SILICONE FILTER TUBE, 45 Deg. L SHAPE 4.9510021 1:8 BLK, SILICONE FILTER TUBE, 90 Deg. L SHAPE 4.9510027 1:8 YEL, SILICONE FILTER TUBE, 45 Deg. L SHAPE 4.9510028 1:8 RED, SILICONE FILTER TUBE, 45 Deg. L SHAPE 4.9510029 1:8 BLUE, SILICONE FILTER TUBE, 45 Deg. L SHAPE 4.9510030 1:8 FILTER, AIR, FOAM, 1 PCS. 6.9510031 1:8 FOAM COVER PRE-FILTER, 2 PCS. 5.9510032 1:8 AIR FILTER, FOAM WITH CAGE, 2 PCS. 14.9510035 1:8 ALUM. CASE (BLUE) AIR FILTER, FOAM 24.9510040 3 PIN FLYWHEEL, TAPERED W/SPACER (.21 SIZE) 14.9510060 1:8 MANIFOLD, BLACK, ROUND WITH SEALS (OFF-ROAD.) 25.9510091 CLUTCH NUT WITH HEX SCREW (FULL) 8.9510100 SPRINGS, 3 SHOE TYPE CLUTCH, MED., GOLD 3+1 PCS. 4.9510101 SPRINGS, 3 SHOE TYPE CLUTCH, PRO GRAY, 3 PCS. 4.9510102 SPRINGS, 3 SHOE TYPE CLUTCH, BLACK, 3 PCS. 4.9510103 SPRINGS, 3 SHOE TYPE CLUTCH, COMP BLACK, 3 PCS. 4.9510111 SCREW 5mm, ENGINE MOUNTS, SPECIAL 4 PCS. 7.9510114 SCREW 5mm, ENGINE MOUNTS, FLAT HEAD 4 PCS. 7.9510120 1:8 EXHAUST SPRING, 2 PC 4.9510182 SILICONE JOINT EXHAUST TUBE, SPECIAL, PINK 5.9510183 SILICONE JOINT EXHAUST TUBE, SPECIAL, YEL 5.9510184 SILICONE JOINT EXHAUST TUBE, SPECIAL, BLUE 5.9510270 CLIPS, FUEL TUBING 3.9510280 SWITCH COVER, SILICONE , 1 PC 3.9510300 ALUMINUM STOPPERS W/ SPRING 4.9510398 CLUTCH BELL , WITH BEARINGS, 12 TEETH 24.9510399 CLUTCH BELL , WITH BEARING, 13 TEETH 19.9510400 CLUTCH BELL , WITH BEARING, 14 TEETH 19.9510401 CLUTCH BELL , WITH BEARING, 15 TEETH 19.9510402 CLUTCH BELL , WITH BEARING, 16 TEETH 19.9510403 CLUTCH BELL , WITH BEARING, 17 TEETH 19.9510404 CLUTCH BELL , WITH BEARING, 18 TEETH 19.9510605 TORSENS DIFF, FRONT - ULTRA GT w/PINION 138.9510606 TORSENS DIFF, CENTER - ULTRA GT w/SPUR 138.9510711 SERVO ARMS KIT, YELLOW, JR/FU/AIR 4.5015072 NUTS, WHEELS, BLUE, 4 PCS. PCS. 5.9530010 GEAR CASE, FRONT OR REAR 14.9530102 BODY MOUNT POSTS, 2 PCS. 0.9530120 GEAR, BEVEL 10.9530121 HARDWARE, GEAR, BEVEL 1.9530130 GEAR, PINION 14.9530151 ARM PINS, INSIDE PINS - 4 LOWER AND 2 UPPER 10.9530152 ARM PINS, OUTSIDE REAR, 2 UP-RIGHT & 4 UPPER 6.9530160 FRONT ARM PLATE HOLDER, UPPER AND LOWER 4.9530171 LEVERS, BRAKE 2 PCS. 1.9530172 RODS, PUSH/PULL, BRAKE 2 PCS. 1.9530180 BRAKE PADS, 2 PCS. 4.9530201 CENTER DIFF, MOUNTINGS, 2 PCS. 13.9530211 5x8mm BUSHING, BRAKE CAM 2 PCS. 0.9530212 5x8mm BEARINGS, BRAKE CAM 2 PCS. 5.9530213 BRAKE CAM, 1 PC, NEW STYLE 4.9530240 FRONT BUMPER 7.9530270 REAR WING MOUNT 13.9530341 BALL END WITH COLLAR, 6mm ANTI- ROLL KIT 3.9530350 REAR ARM PLATE HOLDER. 2 PCS. 5.9530351 REAR ARM PIN HOLDER 3.9530370 SERVO SAVER ARMS, PLASTIC 6.9530380 SERVO SAVER POSTS, 2 PCS. 4.9530401 STEERING ENDS, PLASTIC 2.9530402 3x30mm TIE ROD 2.9530410 STEERING BALL S/ END JOINTS, 6 PCS. 6.9530411 6mm BALLS, 6 PCS. 4.9530480 ENGINE MOUNTS WITH HARDWARE 12.9530490 TUNED PIPE(STOCK) 33.9530491 MOUNT WIRE, TUNED PIPE 1.5030530 THROTTLE JOINT KIT 3.9530560 ANTENNA TUBE PROTECTER AND MOUNT 2.9530620 BEARING, 7 x 19mm, 6 PCS. (DRIVE TRAIN) 29.9530630 BEARING, 6 x 13mm, 12 PCS. (WHEEL HUBS) 59.9530631 BEARING, 6 x 13mm, 2 PCS. 10.9530632 SEALED BEARING, 6 x 13mm, 12 PCS. 66.9530652 CENTER MOUNT PLATE, ALL ULTRA'S 6.95

30700 SCREW/NUT BAG, ULTRA 17.9530701 HEX SET SCREW, MISC. SIZES 9.9530702 CAP, HEX SCREW, MISC. SIZES 9.9530751 DIFF, CASE, FRONT/REAR, K TYPE, REPLACMENT 9.9530761 DIFF, CASE, CENTER, K TYPE, REPLACMENT 9.9530769 DIFF GEARS, BEVEL, 4mm SET 11.9530773 CROSS PIN 4mm, 2 PCS. 3.9530779 MISC. PARTS, NEW DIFF 9.9530800 LINKAGE, BRAKE/THROTTLE (1998) 6.9530901 Cap Joint For Diff 11.9530911 Brake Cap Joint 11.9531010 GEAR, BEVEL 44 TEETH, STEEL 28.9531020 BRAKE DISC, 2 PCS., SPECIAL 16.9531040 GEAR, SPUR, STEEL 29.9531153 BODY, DRAGON RED 49.9531154 BODY, DRAGON BLUE 49.9531155 BODY, DRAGON LIME 49.9531159 BODY, CLIPS, SILVER 4.9531171 ALUM. ARM HOLDERS, FRONT/REAR, 3 PCS. 68.9531190 ALUM. ENGINE MOUNTS, 2 PCS. 54.9531210 ALUM. WING SUPPORT STAYS 75.9531220 ALUM. SERVO ARMS, SET 54.9531320 ALUM. / SEALED "TORK SENSING" DIFF UNIT 135.9531990 TUNED PIPE, EFRA LISTED 39.9532010 SHOCK REPAIR KIT, SEALS , MINOR 8.9532033 SEALS, SHOCK, SILICONE BLADDERS 4 PCS. 5.9532235 VARIOUS PISTONS, TEFLON (SUPER SHOCKS) 7.9534012 Alumi. Radio Post 9.9534013 Water Proof Box (NEW) 11.9534014 Front Chassis Bracer 3.9534015 Sensor Support 2.9534016 Chassis (Hard-Treated) 71.9534017 Air Filter Mount Wire 3.9534018 Front Shock Stay (4mm) 11.9534019 Rear Shock Stay (4mm) 11.9534020 SERVO MOUNTS, 4 PCS. 3.9534021 Upper Arm Alum. Connector 7.9534022 CVA JOINT DRIVE, FRONT AND REAR ULTRA COMP 39.9534023 Bones, CVA JOINT, REBUILD 19.9534024 AXLES, 8mm CVA ULTRA COMP, REBUILD 19.9534025 Radio Tray 11.9534026 LAYDOWN SERVO MOUNTING PARTS 7.9534027 REAR ANTI ROLL BAR 3.9534028 Rear Drive Shaft (100mm) 15.9534031 POST, PLASTIC, RADIO TRAY, 3 PCS. 1.9534032 RADIO AND BATTERY BOX NEW TYPE, ALL ULTRA'S 11.9534033 REAR BODY MOUNT SUPPORT 1.9534041 CHASSIS, KICKUP, HARD COATED 75.9534070 REAR BRACE PLATE, BLUE 8.9534070 Rear Stiffener 8.9534080 MOLDED STONE GUARDS, ULTRA PAIR 11.9534110 BALL BEARINGS 5x10mm, 2 PCS. 7.9535314 NUTS, M3 NYLOK, 20 PCS. 2.9536053 BEARING, 8x16mm, KNUCKLES, PAIR 12.9536054 HEX HUBS, WHEELS, 8mm AXLES, PAIR 11.9536055 PIN, 2.5x17mm, HEX HUBS, 4 PCS. 3.9536081 REAR UP-RIGHT, 8mm AXLES, 2 PCS. 12.9536082 AXLES (FOR DOG BONE), REAR, 8mm AXLES, 2 PCS. 10.9536100 CENTER DOG BONES, SET 16.9536620 SPACER, SHOCK TOWER 3.9536650 BRAKE DISK, STAINLESS STEEL, 2 PCS. 7.9536660 BRAKE PAD, 4 PCS. 3.9536661 BRAKE PAD LININGS, 4 PCS. 3.9536700 STEERING BALL END, 7mm, 8 PCS. 6.9536730 DRIVE CAP JOINTS, 2 PCS. 11.9536740 SERVO SAVER KIT 12.9536741 SPRING, SERVO SAVER 2.9536742 BUSHING, SERVO SAVER, COLLAR, 2 PCS. 1.9536743 6mm E-CLIP, SERVO SAVER, 6 PCS. 2.9536744 METAL POSTS, SERVO SAVER, 2 PCS. 3.9536750 SERVO SAVER CONNECTOR 6.9536760 FRONT PLATE JOINT 9.9536850 7mm BALL, 6 PCS. 3.9536860 5x40mm TURBUCKLES, 2 PCS. 6.9536880 5x60mm TURNBUCKLES 6.9537370 6mm BALL AND SOCKET, 6 PCS. 3.9537370 6mm BALL AND SOCKET, 6 PCS. 3.9538120 POSTS, RADIO POST 7.9538280 TURNBUCKLES, 3x36mm, 2 PCS. 5.9540027 WING MOUNT SUPPORT SET 19.9540052 FRONT SHOCK, THREADED HARDEN BODY, PAIR 54.95

40053 REAR SHOCK, THREADED HARDEN BODY, PAIR 59.9540054 SHAFTS, FRONT SHOCKS, 2 PCS. 7.9540055 SHAFTS, REAR SHOCKS, 2 PCS. 7.9540056 PLASTIC SHOCK PARTS, SET 10.9540057 ADJUSTERS, SHOCK SPRING, 4 PCS. 20.9540058 COVERS, SHOCK SHAFTS, SILICONE, 4 PCS. 9.9540059 SEALS, 14.7mm O-RING, 4 PCS. 4.9540060 NYLOK NUT, 2.5mm, PISTON NUT, 4 PCS. 4.9540065 BALL ENDS, PLASTIC, REAR UPPER 4.9540069 SPRINGS 9.5, BLACK, FRONT AND REAR SET 19.9540070 SPRINGS 9.5, GREEN/SOFT, FRONT AND REAR SET 19.9540071 SPRINGS 9.5, BLUE/MED, FRONT AND REAR SET 19.9540072 SPRINGS 9.5, WHITE/HARD, FRONT AND REAR SET 19.9540076 BODY, FRONT SHOCK, THREADED 16.9540077 BODY, REAR SHOCK, THREADED 16.9540083 WING, REAR, WHITE 15.9540084 WING, REAR, YELLOW 15.9540085 WING, REAR, RED 15.9540086 WING, REAR, LIME 15.9540087 WING, REAR, BLUE 15.9540101 ARMS, FRONT, UPPER, VIOLATOR PAIR 15.9540102 ARMS, FRONT OR REAR, LOWER, VIOLATOR PAIR 15.9540103 KNUCKLES, ALUM. KP, 8mm (VIOLATOR) PAIR 16.9540104 BALLS, 10mm AND SCREW, KP KNUCKLES 4 PCS. 4.9540106 DOG BONE, CVA REPAIR, 9.5 VIOLATOR PAIR 39.9540107 DOG BONE, REAR 101mm, 9.5 VIOLATOR PAIR 16.9540108 TURNBUCKLE, 4x56mm, 9.5 VIOLATOR PAIR 7.9540109 FUEL TANK, 145cc VIOLATOR & ULTRA COMP/MBX 13.9540199 BALL END, 3mm PLASTIC, 6mm BALL TYPE, 4 PCS. 1.9586032 17mm WHEEL, DUAL SPOKE, ORANGE, 4 PACK 19.9586033 17mm WHEEL, DUAL SPOKE, CHROME, 4 PACK 23.9586034 17mm WHEEL, DUAL SPOKE, WHITE, 4 PACK 19.9586035 17mm WHEEL, DUAL SPOKE, YELLOW, 4 PACK 19.9586036 17mm WHEEL, DUAL SPOKE, LIME, 4 PACK 19.9586037 17mm WHEEL, DUAL SPOKE, LIGHT GRAY, 4 PACK 19.9586038 17mm WHEEL, DUAL SPOKE, DARK GRAY, 4 PACK 19.9586039 17mm WHEEL, DUAL SPOKE, RED, 4 PACK 19.9586082 TIRE, BONES W/FOAM, PAIR 19.9590018 SCREW 3x25mm , FULL THREAD, 4 PCS. 1.9590019 SCREW 3x25mm , HALF THREAD, 4 PCS. 1.9590020 2.5mm "E" CLIPS, 20 PCS. 2.9590021 3mm "E" CLIPS, 20 PCS. 3.9590026 HEX SET SCREW, M5x5, 4 PCS. 1.9590035 1:8 FOAM REFILLS, ALUM. CASE AIR FILTER 9.95

91002 MICRO FAIL SAFE UNIT, AUTO BRAKE AND BATTERY CHECK 29.9510213 AC QUICK CHARGER, NiCd AND NiMh BATTERY 4 TO 8 CELLS PACKS 39.9591850 CHARGER, 1 to14 CELLS 12DC AUTO PEAK WITH DISCHARGE 99.9592135 110VAC TO 12VDC 10AMP SWITCHING POWER SUPPLY 49.95

80010 TIRE, SHREDDER, PAIR 21.0080020 TIRE, RIPPER, PAIR 21.0080011 17mm MOUNTED SHREDDERS TIRES, DISH WHEELS, WHITE 31.0080021 17mm MOUNTED RIPPER TIRES, DISH WHEELS, WHITE 31.00

FORCE .21, .25 & .26 ENGINES (REAR EXHAUST)52210 FORCE, 21, P4, 1.7 HP 155.9552211 FORCE, 21, P4, 1.7 HP, PULL START 175.9552213 FORCE, 25, P4, 2.2 HP 179.9552214 FORCE, 25, P4, 2.2 HP, PULL START 199.9552215 FORCE, 26, P4, 2.4 HP, PULL START 199.9552216 DELTA (BLACK BODY) FORCE T8, HIGH RPM, 2.6HP 34kRPM 299.95

OFNA/PICCO .21, .26 ENGINES (REAR EXHAUST).21 PIPE AND MANIFOLD (.21 SPECIAL)51910 .21 PICCO INLINE PIPE & MANIFOLD & SPRING - SEAL, POLISHED 120.9551911 .21 PICCO INLINE MANIFOLD & SPRING - SEAL, POLISHED (USE PIPE #51912) 39.9551912 .21 PICCO INLINE PIPE, POLISHED (USE MANIFOLD #51911) 80.9551913 .21 PICCO MANIFOLD, STANDARD, POLISHED 39.9551999 SPRINGS & SEALES, PICCO INLINE PIPE 6.95.21 size REAR EXHT ENGINE51210 OFNA/PICCO .21 SPORT ENGINE (REAR EXHAUST) 199.9551211 OFNA/PICCO .21 SPORT WITH PULL START ENGINES (REAR EXHUAST) 239.9551213 OFNA/PICCO .26 BIG ENGINE (REAR EXHAUST) 229.9551214 OFNA/PICCO .26 BIG ENGINE WITH PULL START (REAR EXHUAST) 275.9551215 OFNA/PICCO .21 COMP WITH BOOST BOTTLE ENGINES (REAR EXHAUST) 349.9551216 OFNA/PICCO .21 O-1rv WITH BOOST BOTTLE ENGINES (REAR EXHAUST) 399.9551217 OFNA/PICCO .21 O-1bp WITH BOOST BOTTLE ENGINES (REAR EXHAUST) 459.95

PICCO GLOW PLUGS51006 OFNA/ PICCO TURBO MED TEMP - 1 pc. 6.95

51007 OFNA/ PICCO MED TEMP - 1 pc. 5.9551008 OFNA/ PICCO HOT TEMP - 1 pc. 5.9551056 OFNA /PICCO TURBO MED TEMP - 5 PCS. 32.9551057 OFNA /PICCO MED TEMP - 5 PCS. 29.9551058 OFNA /PICCO HOT TEMP - 5 PCS. 29.95

HYPER .21 ENGINES (REAR EXHAUST)53210 HYPER .21 SPORT ENGINE (REAR EXHAUST) 182.9553211 HYPER .21 SPORT WITH PULL START ENGINES (REAR EXHUAST) 199.9553212 HYPER .21 8-PORT WITH PULL START ENGINE (REAR EXHUAST) 219.9553213 HYPER .21 8-PORT WITH PULL START ENGINE (REAR EXHUAST) 199.9553218 HYPER .21 8-PORT RACE ENGINE (REAR EXHUAST) 275.95

WORK STANDS, 1:10 OR 1:8NYLON10900 CAR STAND, ORANGE 17.9510901 CAR STAND, YELLOW 17.9510902 CAR STAND, BLACK 17.9510903 CAR STAND, BLUE 17.95ALUMINUM10904 CAR STAND, ALUM. WITH BEARING TOP, PURPLE 34.9510905 CAR STAND, ALUM. WITH BEARING TOP, BLUE 34.9510906 CAR STAND, ALUM. WITH BEARING TOP, BLACK 34.95

10910 SHOCK REBUILD STAND, ORANGE 7.9510911 SHOCK REBUILD STAND, YELLOW 7.9510911 SHOCK REBUILD STAND, BLUE 7.95

1:8 SCALE CVA'S JOINTSTIRES/WHEELSPRE-GLUED 1:8 SCALE PAIRS

1:8 SCALE 5-SPOKE STAR WHEELS, WHITE86501 17mm MOUNTED 1/8 EXCEL TIRE & STAR WHEEL WHITE PAIR 29.9586502 17mm MOUNTED 1/8 XX-PINS TIRE & STAR WHEEL WHITE PAIR 29.9586504 17mm MOUNTED 1/8 STREET SLICK TIRE & STAR WHEEL WHITE PAIR 29.9586505 17mm MOUNTED 1/8 STREET TREADS TIRE & STAR WHEEL WHITE PAIR 29.9586506 17mm MOUNTED 1/8 X-DASH TIRE & STAR WHEEL WHITE PAIR 29.9586507 17mm MOUNTED 1/8 X=EQUALS TIRE & STAR WHEEL WHITE PAIR 29.9586508 17mm MOUNTED 1/8 GTP SLICK TIRE & STAR WHEEL CHROME PAIR 34.951:8 SCALE DISH WHEELS, WHITE AND YELLOW

1:8 SCALE OFF-ROAD 86000 17mm WHEEL HUB CHANGERS FROM 19mm 9.9581000 TIRES, BLOCK, HARD , PAIR 16.9581001 TIRES, BLOCK, MEDIUM, PAIR 16.9581010 TIRES, "X" PATTERN, HARD , PAIR 16.9581011 TIRES, "X" PATTERN, MEDIUM , PAIR 16.9581030 TIRES, "X" PIN SPIKE, HARD , PAIR 16.9581031 TIRES, "X" PIN SPIKE, MEDIUM , PAIR 16.9581032 TIRES, FIRE, PAIR 19.9581033 TIRES, AVENGER, PAIR 19.9581166 TIRES, MONSTER SPIKE(PIRATE), PAIR 29.9582011 TIRES, STREET, MEDIUM PAIR 16.9582031 FOAM(YELLOW-DOT) TRUED 17mm WHEELS, WHITE 29.9582032 FOAM(GREEN-DOT) TRUED 17mm WHEELS, WHITE 29.9582033 FOAM(BLUE-DOT) TRUED 17mm WHEELS, WHITE 29.9585021 TIRES, WIDE STREET, MED PAIR 19.9585031 TIRES, STEP PINS, NSX PAIR 19.9585041 TIRES, MICRO PINS, NSX PAIR 19.9585061 TIRES, DITTO, YEL DOT, PAIR 19.9585071 TIRES, STAR , YEL DOT, PAIR 19.9585081 TIRES, EQUALS, YEL DOT, PAIR 19.9585091 TIRES, LINES & PINS, YEL DOT, PAIR 19.9586001 TIRE, X= PINS, ORANGE, PAIR 19.9586002 TIRE, X= PINS, CHERRY, PAIR 19.9586003 TIRE, X= PINS, BLUE, PAIR 19.9586004 TIRE, X= PINS, YELLOW, PAIR 19.9586005 TIRE, FIRE, LIME, PAIR 19.9586006 TIRE, X PINS, GRAY, PAIR 19.9586007 TIRE, FIRE, CHERRY, PAIR 19.9586008 TIRE, FIRE, BLUE, PAIR 19.9586009 TIRE, FIRE, YELLOW, PAIR 19.9586010 TIRE, FIRE, ORANGE, PAIR 19.9581034 TIRE, AVENGER, RED, PAIR 19.9581035 TIRE, AVENGER, GREEN, PAIR 19.9581036 TIRE, AVENGER, YELLOW, PAIR 19.9581037 TIRE, AVENGER, BLUE, PAIR 19.9586011 TIRE, MED. SPIKE, MEDIUM, PAIR 16.9586021 TIRE, X - DASH SPIKE, SPECIAL GRIP, PAIR 19.95

86031 TIRE, EXCEL, SPECIAL GRIP, PAIR 19.9586061 TIRE, TRUCK, PAIR 19.9586062 TIRE, X-EQUALS SPIKE, PAIR 19.9586071 TIRE, ULTRA PINS W/H, PAIR 19.9586081 TIRE, "K" TIRE (FUZZIE), PAIR 19.9586082 TIRE, BONES (46) TIRE, PAIR 19.9586091 TIRE, XX-PIN SPIKE, PAIR 19.9586092 TIRE, ENZO (46) TIRE, PAIR 19.9586063 TIRES, MONSTER TRUCK, PAIR 29.951:8 STREET TIRES86050 TIRES, SLICK TIRE W/O BELT, PAIR 19.9586051 TIRES, SLICK TIRE WITH BELT, PAIR 35.9586052 TIRES, STREET TIRE W/O BELT, PAIR 19.9586053 TIRES, STREET TIRE WITH BELT, PAIR 35.9581156 TIRES, MT NIK DOMINATOR, PAIR 24.9581157 TIRES, MT SPIKE DOMINATOR, PAIR 24.9581158 TIRES, MT OVAL PIN DOMINATOR, PAIR 24.95

JAMMIN TIRES AND MOUNTED TIRES ON DISH WHEELS80010 TIRE, SHREDDER, PAIR 21.0080020 TIRE, RIPPER, PAIR 21.0080011 17mm MOUNTED SHREDDERS TIRES, DISH WHEELS, WHITE 31.0080021 17mm MOUNTED RIPPER TIRES, DISH WHEELS, WHITE 31.001:8 WHEELS81015 17mm WHEELS, STOCK, 4 PACK 19.9581025 17mm 17mm WHEELS, 6 SPOKE, 4 PACK 19.9581026 17mm 17mm WHEELS, CHROME 6 SPOKE, 4 PACK 23.9581045 17mm WHEELS, 3 SPOKE, 17mm WHITE, 4 PACK 19.9581051 17mm WHEELS, HYPER , 17mm WHITE, 4 PACK 19.9581052 17mm WHEELS, HYPER , GRAY, 4 PACK 19.9581053 17mm WHEELS, HYPER ,BLACK, 4 PACK 19.9581054 17mm WHEELS, HYPER ,YELLOW, 4 PACK 19.9581153 17mm WHEELS, MT 3 SPLIT SPOKE, 4 PACK CHROME 21.9581154 17mm WHEELS, MT 3 SPLIT SPOKE, 4 PACK YELLOW 19.9581155 17mm WHEELS, MT 3 SPLIT SPOKE, 4 PACK 17mm WHITE 19.9581164 17mm WHEELS, MONSTER SPIKE, CHROME, PAIR 19.9581165 17mm WHEELS, MONSTER SPIKE, WHITE, PAIR 14.9586024 17mm WHEEL, V SPOKE, BLUE, 4 PACK 19.9586025 17mm WHEEL, V SPOKE, LIME, 4 PACK 19.9586026 17mm WHEEL, V SPOKE, WHITE, 4 PACK 19.9586027 17mm WHEEL, V SPOKE, ORANGE, 4 PACK 19.9586028 17mm WHEEL, V SPOKE, GRAY, 4 PACK 19.9586029 17mm WHEEL, V SPOKE, YELLOW, 4 PACK 19.9586030 17mm WHEEL, V SPOKE, CHROME, 4 PACK 23.9586032 17mm WHEEL, DUAL SPOKE, ORANGE, 4 PACK 19.9586033 17mm WHEEL, DUAL SPOKE, CHROME, 4 PACK 23.9586034 17mm WHEEL, DUAL SPOKE, WHITE, 4 PACK 19.9586035 17mm WHEEL, DUAL SPOKE, YELLOW, 4 PACK 19.9586036 17mm WHEEL, DUAL SPOKE, LIME, 4 PACK 19.9586037 17mm WHEEL, DUAL SPOKE, LIGHT GRAY, 4 PACK 19.9586038 17mm WHEEL, DUAL SPOKE, DARK GRAY, 4 PACK 19.9586039 17mm WHEEL, DUAL SPOKE, RED, 4 PACK 19.9586040 17mm WHEEL, DISH, WHITE, 4 PACK 18.9586041 17mm WHEEL, DISH, YELLOW, 4 PACK 18.9586042 17mm WHEEL, DISH, BLACK, 4 PACK 18.9586044 17mm WHEEL, 5 SPOKE(STAR), RED, 4 PACK 19.9586045 17mm WHEEL, 5 SPOKE(STAR), WHITE, 4 PACK 19.9586046 17mm WHEEL, 5 SPOKE(STAR), LIME, 4 PACK 19.9586047 17mm WHEEL, 5 SPOKE(STAR), YELLOW, 4 PACK 19.9586048 17mm WHEEL, 5 SPOKE(STAR), BLACK, 4 PACK 19.9586049 17mm WHEEL, 5 SPOKE(STAR), CHROME, 4 PACK 23.9586055 17mm WHEEL, 17x12mm Blazer TRUCK, WHITE, PAIR 19.9586065 17mm WHEELS, MONSTER TRUCK, CHROME, PAIR 19.95

81091 ORANGE, 1:8 FOAM DONUTS, SOFT/MED. 4 PCS. 9.9581092 BLUE, 1:8 FOAM DONUTS, MED., 4 PCS. 10.9581093 POSITIVE, 1:8 FOAM DONUTS, BLK:BLU:BLK, 4 PCS. 15.9581094 NEGATIVE, 1:8 FOAM DONUTS, BLU:BLK:BLU, 4 PCS. 15.9581095 GRAY, 1:8 FOAM DONUTS, HARD, 4 PCS. 10.9581168 BLUE MONSTER TIRE, 1:8 FOAM DONUTS, MED., 4 PCS. 14.95

1:10, 1:8 SCALE UNIVERSAL PARTS3 SHOE CLUTCH KIT AND PARTS

10265 3 SHOE CLUTCH KIT, SG SHAFT TYPE 33.9510266 3 SHOE CLUTCH KIT, (OPS, PICCO, N.R., REX) 33.9510267 3 SHOE CLUTCH KIT, (O.S., ROYAL) 33.9559031 3 SHOE CLUTCH KIT, (O.S. CZ-R/Z, OFNA, TNT) 33.9510010 SHOES, 3 SHOE TYPE, CARBON BLACK, 3 PCS. 12.9510011 SHOES, 3 SHOE TYPE, ALUM. CNC BLUE, LITE WEIGHT, 3 PCS. 24.9510012 SHOES, 3 SHOE TYPE, ALUM. CNC PURPLE, MED. WEIGHT, 3 PCS. 24.95

10100 SPRINGS, 3 SHOE TYPE CLUTCH, MED., GOLD 3+1 PCS. 4.9510101 SPRINGS, 3 SHOE TYPE CLUTCH, PRO GRAY, 3 PCS. 4.9510102 SPRINGS, 3 SHOE TYPE CLUTCH, BLACK, 3 PCS. 4.9510103 SPRINGS, 3 SHOE TYPE CLUTCH, COMP BLACK, 3 PCS. 4.9510040 3 PIN FLYWHEEL, TAPERED W/SPACER (.21 SIZE) 14.9510041 3 PIN FLYWHEEL, STRAIGHT HOLE (.21 SIZE) 14.9510043 3 PIN FAN FLYWHEEL, TAPER (.21 SIZE) 27.9559021 3 PIN FLYWHEEL, ALUM., (.12/15 SIZE) 14.9559022 3 PIN ALUM. FAN, FLYWHEEL, (.12/15 SIZE) 29.95

4 SHOE CLUTCH KIT AND PARTS10260 4 SHOE CLUTCH KIT, (OPS, PICCO, N.R., REX) 33.9510261 4 SHOE CLUTCH KIT, (O.S., ROYAL) 33.9510271 4 SHOE CLUTCH KIT, SG SHAFT TYPE 33.9559029 4 SHOE CLUTCH KIT, BLUE FLYWHEEL (O.S. CZ-R/Z, OFNA, TNT) 31.9559030 4 SHOE CLUTCH KIT, (O.S. CZ-R/Z, OFNA, TNT) 31.9510269 SPRINGS, 4 SHOE TYPE CLUTCH, 4 PCS. 5.9510268 SHOES, 4 SHOE TYPE CARBON, 4 PCS. 13.95

CLUTCH PARTS FOR .12 AND .2110048 SHIM SPACERS, .285IN (FOR FLYWHEEL), 10 PCS. 4.5010320 HUB, DRIVE WITH SLIT METAL CORN 7.9510330 SLIT METAL CORN 2.9559020 CLUTCH NUT, HEX SCREW, (.12 SIZE) 8.9510090 CLUTCH NUT WITH E CLIP 8.5010091 CLUTCH NUT WITH HEX SCREW (FULL) 8.9510098 CLUTCH NUT SG SHAFTS 4.9510099 CLUTCH NUT SHIM KIT 5.50CLUTCH BELLS

NEEDLE BEARING TYPE10080 CLUTCH BELL 15 TEETH (NEED 10050, NEEDLE) 16.9510081 CLUTCH BELL 14 TEETH (NEED 10050, NEEDLE) 16.9510082 CLUTCH BELL 13 TEETH (NEED 10050, NEEDLE) 16.9510050 BEARING, NEEDLE, FOR CLUTCH BELL 3.95

HARDEN BELLS WITH BEARINGS, 5x10 BEARING10398 CLUTCH BELL , WITH BEARINGS, 12 TEETH 24.9510399 CLUTCH BELL , WITH BEARING, 13 TEETH 19.9510400 CLUTCH BELL , WITH BEARING, 14 TEETH 19.9510401 CLUTCH BELL , WITH BEARING, 15 TEETH 19.9510402 CLUTCH BELL , WITH BEARING, 16 TEETH 19.9510403 CLUTCH BELL , WITH BEARING, 17 TEETH 19.9510404 CLUTCH BELL , WITH BEARING, 18 TEETH 19.9534110 BALL BEARINGS, 5x10mm 2 PCS. 7.95

2 SPEED TRANSMISSION (NEW REVISION 2 MODEL) - OFNA CARS 1:8 (MONSTER, NOT RECOMMENDED & PIRATE) SERPENT TYPE/FIT GEARS35001 2-SPEED KITS, CAM LEVER TYPE, , ULTRA'S, BLAZER, GTP, REV 2 99.9535011 2-SPEED KITS, CLUTCH TYPE, , ULTRA'S, BLAZER, GTP, REV 3 124.9535002 2-SPEED KIT, CAM LEVER TYPE, INFERNO (NOT MP5/ 6), REV 2 119.9535003 2-SPEED KIT, CAM LEVER TYPE, MUGEN MBX, REV 2 119.9535219 ALUM. NUT, CW NUT, LARGE, 2-SPEED REV 3 2.9535220 GEARS, 2-SPEED SET, 13T/17T REV 2 & 3 19.9535221 BASE, CLUTCH BELL, SCREW-ON BASE REV 2 & 3 28.9534110 BEARING, 5x10mm 2 PCS. 7.9535222 SHAFT, OFNA CARS, 2-SPEED REV2 & 3 11.9535223 SHAFT, KYOSHO 7.5, 2-SPEED REV2 11.9535224 SHAFT, MUGEN MBX, 2-SPEED REV2 11.9535225 ALUM.HOLDER, 1ST GEAR, 2-SPEED REV2 & 3 26.9535226 ALUM.HOLDER, 2ND GEAR, 2-SPEED REV2 24.9535227 CLUTCH CAM DISC., 2-SPEED REV2 13.9535228 ALUM. NUT, CCW NUT, LARGE, 2-SPEED REV2 & 3 2.9535229 E-CLIP, 18mm 0.9535230 BEARING, 8x12 FLANGE, 2 PCS. 12.9535231 ALUM. SPACER, 8x10mm 1.9535232 GEARS, 2-SPEED SET, 14T/18T REV 2 & 3 19.9535233 GEARS, 2-SPEED SET, 15T/19T REV 2 & 3 19.9535234 ALUM. 2ND GEAR CLUTCH BELL REV 3 24.9535235 ALUM. CLUTCH SHOE CARRIER CAM REV 3 5.9535236 SHOES, 2ND GEAR, REV 3 14.9535237 MISC. PARTS, 2-SPEED REV 3 9.9535233 GEARS, 2-SPEED SET, 15T/19T REV 2 & 3 19.9535249 SPUR GEAR, 49T, 2-SPEED REV2 7.9535246 SPUR GEAR, 46T, 2-SPEED REV2 7.9535248 SPUR GEAR, 48T, 2-SPEED REV2 7.9535247 SPUR GEAR, 47T, 2-SPEED REV2 7.9535245 SPUR GEAR, 45T, 2-SPEED REV2 7.9535244 SPUR GEAR, 44T, 2-SPEED REV2 7.95

1:8 SCALE PART MAINLY FOR .21 ENGINES10013 MOUNT WIRE, AIR FILTER, 9.5 CAR 3.9510014 MOUNT WIRE, AIR FILTER, ULTRA'S 3.9510015 OIL, FOAM AIR FILTER, 30cc 2.9510016 FOAM, REPLACEMENTS, 2 PCS. 5.95

10017 AIR FILTER, FOAM, BLUE 5.9510018 AIR FILTER, FOAM, NEON YELLOW 5.9510019 AIR FILTER, FOAM, NEON PINK 5.9510020 1:8 BLK, SILICONE FILTER TUBE, 45 Deg. L SHAPE 4.9510021 1:8 BLK, SILICONE FILTER TUBE, 90 Deg. L SHAPE 4.9510027 1:8 YEL, SILICONE FILTER TUBE, 45 Deg. L SHAPE 4.9510028 1:8 RED, SILICONE FILTER TUBE, 45 Deg. L SHAPE 4.9510029 1:8 BLUE, SILICONE FILTER TUBE, 45 Deg. L SHAPE 4.9510030 1:8 FILTER, AIR, FOAM, 1 PCS. 6.9510031 1:8 FOAM COVER PRE-FILTER, 2 PCS. 5.9510032 1:8 AIR FILTER, FOAM WITH CAGE, 2 PCS. 14.9510035 1:8 ALUM. CASE (BLUE) AIR FILTER, FOAM 24.9590035 1:8 FOAM REFILLS, ALUM. CASE AIR FILTER 9.9510060 1:8 MANIFOLD, BLACK, ROUND WITH SEALS (OFF-ROAD.) 25.9510061 1:8 MANIFOLD, S TYPE ROUND WITH SEALS (ON-ROAD.) 19.9510066 1:10 INLINE TUNED PIPE, OFNA-X12, POLISHED 49.9510067 .15 ENG. ROUND PORT SILICONE SEALS, 2 PCS. 3.9510069 1:8 ROUND PORT SILICONE SEALS, RED, 2 PCS. 6.9510070 1:8 TUNED PIPE W/METAL NIPPLE 26.9510056 1:8 INLINE TUNED PIPE, OFNA-086, POLISHED 69.9510057 1:8 INLINE TUNED PIPE, OFNA-063, POLISHED 69.9510077 1:8 INLINE TUNED PIPE, OFNA-053, POLISHED 69.9510078 ALUM. CNC PIPE MOUNTING POST KIT 4.9510079 ALUM. PRESSURE NIPPLE, RIGHT ANGLE, 3 COLOR CHOICES 4.9531990 1:8 PIPE, TUNED, DUAL CHAMBER, BLACK 39.9531991 MANIFOLD, .21 POLISHED W/SPRING 25.9531992 1:8 PIPE, TUNED, POLISHED DUAL CHAMBER 34.9510110 1:8 ENGINE MOUNTING BLOCK W/ HARDWARE, 2 PCS. 11.5010111 SCREW 5mm, ENGINE MOUNTS, SPECIAL 4 PCS. 8.5010114 SCREW 5mm, ENGINE MOUNTS, FLAT HEAD 4 PCS. 7.9510112 1:8 ENGINE MOUNTING ALUMINUM, 2 PCS. 54.9510120 1:8 EXHAUST SPRING, 2 PC 4.9510130 1:8 MANIFOLD, FLAT (OS RFB ENGINES) 24.9510180 JOINT, EXHAUST TUBE, BLUE, 1 PC 4.9510182 SILICONE JOINT EXHAUST TUBE, SPECIAL, PINK 5.9510183 SILICONE JOINT EXHAUST TUBE, SPECIAL, YEL 5.9510184 SILICONE JOINT EXHAUST TUBE, SPECIAL, BLUE 5.95

HARDWARE PARTS AND SPECIALTY ITEMS10140 BLUE ALUM. CNC ANTENNA HOLDER W/ TUBE 4.9510141 ROSE ALUM. CNC ANTENNA HOLDER W/ TUBE 4.9510142 SILVER ALUM. CNC ANTENNA HOLDER W/ TUBE 4.9510159 BOTTLE WITH ALUM CNC SPOUT, 300cc 7.9510160 BOTTLE WITH ALUM TUBE SPOUT, 500cc 5.9510161 BOTTLE WITH AUTO STOP SPOUT, 500cc 8.9510162 BOTTLE WITH ALUM TUBE SPOUT, 250cc 3.9510163 JUST THE TOP & TUBE, COKE/FUEL BOTTLE SCREW-ON 3.9510164 BOTTLE WITH ALUM CNC SPOUT, 500cc 10.9510167 BOTTLE WITH ALUM CNC SPOUT, 750cc 11.9510165 ALUMINUM FUEL FILTER, FINE MESH 5.9510166 ALUMINUM (LARGE) FUEL FILTER, STONE 9.9510168 ALUMINUM FUEL FILTER & PRIMER PUMP, STONE 11.9510207 ALUM.GLO-STARTER WITH METER & CHARGER 29.9510209 110VAC DUAL CHARGER, 4.8V & 9.6V Tx & Rc, FU PLUG 19.9510210 110VAC DUAL CHARGER, 4.8V & 9.6V Tx & Rc, JR PLUG 19.9510211 BATTERY PACK, 5 CELL NiMh, 1200, FLAT 29.9510212 BATTERY PACK, 5 CELL NiMh, 1200, HUMP 29.9510214 NiMh BATTERY CHARGER, 110 VAC (4 HOUR TYPE) 7.9510216 GLOW PLUG HEATER WITH DRIVER FOR 12Vdc 29.9510217 RED GLOW-STARTER 1,700maH w/ CHARGER 19.9510218 RED GLOW-STARTER "C" BATTERY (RED) 8.9510219 RED GLOW-STARTER "D" BATTERY (RED) 9.9510220 GLOW-STARTER, 13OOmAh BATTERY WITH CHARGER, TWIST LOCK 21.9510221 GLOW-STARTER, ALUM. RED WITH BAT & METER / NO CHARGER 24.9510222 GLOW-STARTER, ALUM. RED WITH BAT & METER / NO CHARGER 24.9510223 110VAC CHARGER, GLOW STARTER 8.9510224 12V BATTERY CHARGER, 110AC 11.9510225 ALUM. GLOW-STARTER "D" BATTERY 14.9510226 ALUM. GLOW-STARTER "C" BATTERY 12.9510227 GLOW-STARTER 1,300maH w/ CHARGER 19.9510228 GLOW-STARTER 1,300maH w/ METER (NO CHARGER) 17.9510229 DC 12V GLOW CHARGER UNIT 19.9510230 DIFF. LOCK LUBE, 35cc 8.9510231 1000 WT SILICONE OIL 8.9510232 3000 WT SILICONE OIL 8.9510233 5000 WT SILICONE OIL 8.9510234 7000 WT SILICONE OIL 8.9510235 10,000 WT SILICONE OIL 9.9510236 30,000 WT SILICONE OIL 9.9510237 50,000 WT SILICONE OIL 9.9510238 120,000 WT SILICONE OIL 9.95

10240 DIFF. LUBE, HIGH TEMP., 35cc (GREEN) 9.9510270 CLIPS, FUEL TUBING 3.9510272 S" CLIPS, FUEL TUBING 6 PCS. 3.9510273 SERVO BAR MOUNTS, NYLON BLUE 3.9510280 SWITCH COVER, SILICONE , 1 PC 3.9510290 WASHER, ALUM. SERVO, 3mm 6.9510291 LINKAGE GUIDES. 4 SETS 5.9510292 THROTTLE BALL JOINTS, 5 PCS. 3.9510300 ALUMINUM STOPPERS W/ SPRING 4.9510321 RED ALUM. STOPPERS KIT 4.9510322 YELLOW ALUM. STOPPERS KIT 4.9510323 BLUE/PURPLE ALUM. STOPPERS KIT 4.9510331 GOLD 3mm CONE WASHER, 10 PCS. 4.9510332 RED3mm CONE WASHER, 10 PCS. 4.9510333 BLUE 3mm CONE WASHER, 10 PCS. 4.9510341 GOLD 3mm CONCAVE WASHER, 20 PCS. 7.9510342 RED 3mm CONCAVE WASHER, 20 PCS. 7.9510343 BLUE 3mm CONCAVE WASHER, 20 PCS. 7.9510344 BLUE 3mm CONCAVE WASHER W/SCREW 15 PCS. 8.9510345 ROSE 3mm CONCAVE WASHER W/SCREW 15 PCS. 8.9510346 BLUE 3mm CAP WASHER W/SCREW 15 PCS. 8.9510347 ROSE 3mm CAP WASHER W/SCREW 15 PCS. 8.9510351 GOLD 4mm CONCAVE WASHER, 20 PCS. 7.9510352 RED 4mm CONCAVE WASHER, 20 PCS. 7.9510353 BLUE 4mm CONCAVE WASHER, 20 PCS. 7.9510361 GOLD 3mm NYLOK NUTS, 10 PCS. 7.9510362 RED 3mm NYLOK NUTS, 10 PCS. 7.9510363 BLUE 3mm NYLOK NUTS, 10 PCS. 7.9510371 GOLD 4mm NYLOK NUTS, 10 PCS. 7.9510372 RED 4mm NYLOK NUTS, 10 PCS. 7.9510373 BLUE 4mm NYLOK NUTS, 10 PCS. 7.9510375 BLUE FLANGE 4mm NYLOK NUTS, 10 PCS. 8.9510376 PURPLE FLANGE 4mm NYLOK NUTS, 10 PCS. 8.9510377 SERVO ALUM BAR MOUNTS, BLUE 5.9510378 SERVO ALUM BAR MOUNTS, PURPLE 5.95

HEAVY DUTY SERVO SAVER WITH GOLD CNC ALUM. TOP10760 SERVO SAVER, HD w/CNC TOP, BLUE (AIR, SANWA, FU, HITEC, JR) 8.9510761 SERVO SAVER, HD w/CNC TOP, RED (AIR, SANWA, FU, HITEC, JR) 8.9510762 SERVO SAVER, HD w/CNC TOP, PURPLE (AIR, SANWA, FU, HITEC, JR) 8.9510763 SERVO SAVER, HD w/CNC TOP, YELLOW (AIR, SANWA, FU, HITEC, JR) 8.9510769 INSERTS SERVO SAVER, ALL RADIO'S (AIR, SANWA, FU, HITEC, JR) 0.95

HEAVY DUTY SERVO ARMS WITH GOLD CNC ALUM. TOP10765 SERVO HORN, HD w/CNC TOP, BLUE (AIR, SANWA, FU, HITEC, JR) 8.9510766 SERVO HORN, HD w/CNC TOP, RED (AIR, SANWA, FU, HITEC, JR) 8.9510767 SERVO HORN, HD w/CNC TOP, PURPLE (AIR, SANWA, FU, HITEC, JR) 8.9510768 SERVO HORN, HD w/CNC TOP, YELLOW (AIR, SANWA, FU, HITEC, JR) 8.9510769 INSERTS SERVO SAVER, ALL RADIO'S (AIR, SANWA, FU, HITEC, JR) 0.95

HEAVY DUTY NYLON WITH STEEL RING SERVO ARMS FOR NITRO CARS 1:10 AND 1:8TH SCALES10701 LINKAGE SLIDERS KIT, YELLOW 2.9510702 LINKAGE SLIDERS KIT, PINK 2.9510703 LINKAGE SLIDERS KIT, ORANGE 2.9510704 LINKAGE SLIDERS KIT, BLUE 2.9510705 LINKAGE SLIDERS KIT, PURPLE 2.9510711 SERVO ARMS KIT, YELLOW, JR/FU/AIR 4.5010712 SERVO ARMS KIT, PINK, JR/FU/AIR 4.5010713 SERVO ARMS KIT, ORANGE, JR/FU/AIR 4.5010714 SERVO ARMS KIT, BLUE, JR/FU/AIR 4.5010715 SERVO ARMS, PURPLE, JR/FU/AIR 4.5010721 SERVO LINKAGE KIT, YELLOW, JR/FU/AIR 7.9510722 SERVO LINKAGE KIT, PINK, JR/FU/AIR 7.9510723 SERVO LINKAGE KIT, ORANGE, JR/FU/AIR 7.9510724 SERVO LINKAGE KIT, BLUE, JR/FU/AIR 7.9510725 SERVO LINKAGE KIT, PURPLE, JR/FU/AIR 7.9510726 STEERING LINKAGE KIT, YELLOW, JR/FU/AIR 9.9510727 STEERING LINKAGE KIT, PINK, JR/FU/AIR 9.9510728 STEERING LINKAGE KIT, ORANGE, JR/FU/AIR 9.9510729 STEERING LINKAGE KIT, BLUE, JR/FU/AIR 9.95

SUPER DUTY ALUMINUM CNC SERVO ARMS FOR NITRO CARS 1:10 AND 1:8TH SCALES10730 ALUM. CNC SERVO ARM, YELLOW, JR/FU/AIR/HI 5.9510731 ALUM. CNC SERVO ARM, BLUE, JR/FU/AIR/HI 5.9510732 ALUM. CNC SERVO ARM, PURPLE, JR/FU/AIR/HI 5.9510733 ALUM. CNC SERVO ARM, RED, JR/FU/AIR/HI 5.9510740 ALUM. CNC DOUBLE SERVO ARM, YELLOW, JR/FU/AIR/HI 6.9510741 ALUM. CNC DOUBLE SERVO ARM, BLUE, JR/FU/AIR/HI 6.9510742 ALUM. CNC DOUBLE SERVO ARM, PURPLE, JR/FU/AIR/HI 6.9510743 ALUM. CNC DOUBLE SERVO ARM, RED, JR/FU/AIR/HI 6.9510750 ALUM. CNC L-SHAPE SERVO ARM, YELLOW, JR/FU/AIR/HI 6.95

10751 ALUM. CNC L-SHAPE SERVO ARM, BLUE, JR/FU/AIR/HI 6.9510752 ALUM. CNC L-SHAPE SERVO ARM, PURPLE, JR/FU/AIR/HI 6.9510753 ALUM. CNC L-SHAPE SERVO ARM, RED, JR/FU/AIR/HI 6.9510759 INSERTS FOR ALUM. CNC SERVO ARM, JR/FU/AIR/HI, 2 SETS 3.95

HAND TOOLS AND KITS10309 SLIM LONG TUNING DRIVER 1.9510310 ENGINE TUNING SCREWDRIVER, 3 PCS. 8.9510311 HEX 1/4 WRENCH TOOL SET, METRIC 1.5, 2.0, 2.5, 3.0mm 29.9593111 HEX 1/4 DRIVE BIT, 3.00mm (METRIC) 7.9593112 HEX 1/4 DRIVE BIT, 2.50mm (METRIC) 7.9593113 HEX 1/4 DRIVE BIT, 2.00mm (METRIC) 7.9593114 HEX 1/4 DRIVE BIT, 1.50mm (METRIC) 7.9593119 SET, HEX 1/4 DRIVE BITS, NO HANDLE (METRIC) 28.9510312 HEX 1/4 WRENCH TOOL SET, U.S. STANDARD 29.9593121 HEX 1/4 DRIVE BIT, 3/32 (US STD.) 7.9593122 HEX 1/4 DRIVE BIT, 5/64 (US STD.) 7.9593123 HEX 1/4 DRIVE BIT, 1/16 (US STD.) 7.9593124 HEX 1/4 DRIVE BIT, .050 (US STD.) 7.9593129 SET, HEX 1/4 DRIVE BITS, NO HANDLE (US STD.) 28.9510797 .12/.15 ENGINE BEARING PULLER KIT, N.ROSSI .12 &.15 ENGINES 69.9510798 .21 ENGINE BEARING PULLER KIT, 13mm AND 14mm SIZE 69.9510799 WRENCH, FLYWHEEL & 17mm 6.9510800 CROSS WRENCH, GLOW PLUG TYPE 5.9510801 CROSS WRENCH, WHEEL NUT & GLOW PLUG TYPE 12.9510802 WHEEL WRENCH, MONSTER WHEELS 5.9510803 TOOL, HOLE CUTTER (REAM), BLACK 19.9510804 TOOL, HOLE CUTTER (REAM), BLUE 19.9510805 TOOL, HOLE CUTTER (REAM), PURPLE 19.9510810 SNR CROSS WRENCH, LD3, 10; 5; 2.5; 8mm 14.95

MISC. HARDWARE PARTS10178 FUEL LINE TUBING, HARD WALL, SILICONE, 100cm YELLOW 1.9510179 FUEL LINE TUBING, HARD WALL, SILICONE, 100cm BLUE 1.9510500 MP7.5 ADJUSTABLE ENGINE MOUNTS 59.9590009 HEX CHASSIS SCREWS, COUNTER SINK 20 PCS. 5.9590010 BIG RUBBER BANDS, 2 PCS. 2.9590011 2mm COLLARS, 5 PCS. 5.9590012 METAL NIPPLE, RIGHT ANGLE, 2 PCS. 4.9590013 METAL NIPPLE, STRAIGHT, 2 PCS. 2.9590014 STEERING PIVOT BALLS, 4 PCS. 4.9590015 METAL TUBES (USED WITH GEARS SCREWS) 4 PCS. 2.9590016 SPRINGS (USED WITH BRAKE CLAMP) 4 PCS. 2.5090018 SCREW, CAP 3x25mm, 4PCS FULL THREAD 2.9590019 SCREW, CAP 3x25mm, 4PCS HALF THREAD 2.9590020 2.5mm "E" CLIPS, 20 PCS. 2.5090021 3mm "E" CLIPS, 20 PCS. 3.5090022 4mm "E" CLIPS, 20 PCS. 3.5090023 SHIM, WASHERS .2MM (CLUTCH BELL) 4 PCS. 2.5090024 SHIM, WASHERS 7X10mm (0.3mm THICK) DIFF. 4 PCS. 2.5090026 HEX SET SCREW, M5x5, 4 PCS. 1.9590027 HEX SET SCREW, M5x6, 4 PCS. 1.9590028 EXHAUST MOUNTING WIRE 2.50

ALUM. 7075 ALLOY HARDWARE, SCREWS, NUTS, WASHERS & SPACER KITS10950 HARDWARE ASRTMNT,ALUM. BLUE 59.9510951 HARDWARE ASRTMNT,ALUM.PURPLE 59.9510955 SCREW,HEX HEAD,M3x8 BLUE 10P 4.9510956 SCREW,HEX HEAD,M3x8 PURPLE 10P 4.9510957 SCREW,HEX HEAD,M3X12 BLUE 10P 4.9510958 SCREW,HEX HEAD,M3X12PURPLE 10P 4.9510959 SCREW,HEX HEAD,M3X18 BLUE 10P 4.9510960 SCREW,HEX HEAD,M3X18PURPLE 10P 4.9510961 SCREW,HEX HEAD,M3X20 BLUE 10P 4.9510962 SCREW,HEX HEAD,M3X20PURPLE 10P 4.9510963 SCREW, RD HEAD,M3X8 BLUE 10P 4.9510964 SCREW, RD HEAD,M3X8 PURPLE 10P 4.9510965 SCREW, RD HEAD,M3X12 BLUE 10P 4.9510966 SCREW, RD HEAD,M3X12PURPLE 10P 4.9510967 SCREW,FLAT HEAD,M3X8 BLUE 10P 4.9510968 SCREW,FLAT HEAD,M3X8PURPLE 10P 4.9510969 SCREW,FLAT HEAD,M3X12 BLUE 10P 4.9510970 SCREW,FLAT HEAD,M3X12PURPLE10P 4.9510971 SCREW,FLAT TP,M3X8 BLUE 10P 4.9510972 SCREW,FLAT TP,M3X8 PURPLE 10P 4.9510973 SCREW,FLAT TP,M3X12 BLUE 10P 4.9510974 SCREW,FLAT TP,M3X12 PURPLE 10P 4.9510975 WASHER,COUNTERSINK,3mm BLU 10P 3.9510976 WASHER,COUNTERSINK,3M PURPLE10 3.9510977 WASHER, CONE, 3mm BLUE 10P 3.9510978 WASHER, CONE, 3mm PURPLE 10P 3.95

10979 WASHER,COUNTERSINK,4m BLUE 10P 3.9510980 WASHER,COUNTERSINK,4mPURPLE10P 3.9510981 NYLOK NUT, 3mm BLUE 10P 5.9510982 NYLOK NUT, 3mm PURPLE 10P 5.9510983 NYLOK NUT, 4mm BLUE 10P 5.9510984 NYLOK NUT, 4mm PURPLE 10P 5.9510985 NYLOK FLANGE NUT,4mm BLUE 10P 8.9510986 NYLOK FLANGE NUT,4mmPURPLE 10P 8.95STEEL BLACK ALLOY HARDWARE, HEX SCREWS & NUTS94001 SCREW, HEX, M3x4 BUTTON HEAD 4 PCS. 1.9594002 SCREW, HEX, M3x8 BUTTON HEAD 4 PCS. 1.9594003 SCREW, HEX, M3X10 BUTTON HEAD 4 PCS. 1.9594004 SCREW, HEX, M3X12 BUTTON HEAD 4 PCS. 1.9594005 SCREW, HEX, M3X16 BUTTON HEAD 4 PCS. 1.9594006 SCREW, HEX, M3X18 BUTTON HEAD 4 PCS. 1.9594007 SCREW, HEX, M3X20 BUTTON HEAD 4 PCS. 1.9594008 SCREW, HEX, M3X25 BUTTON HEAD 4 PCS. 1.9594009 SCREW, HEX, M4X10 BUTTON HEAD 4 PCS. 1.9594010 SCREW, HEX, M4X12 BUTTON HEAD 4 PCS. 1.9594011 SCREW, HEX, M4X16 BUTTON HEAD 4 PCS. 1.9594012 SCREW, HEX, M4X20 BUTTON HEAD 4 PCS. 1.9594013 SCREW, HEX, M4X25 BUTTON HEAD 4 PCS. 1.9594014 SCREW, HEX, M4X45 BUTTON HEAD 4 PCS. 1.9594018 SCREW, HEX, M3x5 FLAT HEAD 4 PCS. 1.9594019 SCREW, HEX, M3X10 FLAT HEAD 4 PCS. 1.9594020 SCREW, HEX, M3X12 FLAT HEAD 4 PCS. 1.9594021 SCREW, HEX, M3X15 FLAT HEAD 4 PCS. 1.9594022 SCREW, HEX, M3X18 FLAT HEAD 4 PCS. 1.9594023 SCREW, HEX, M3X25 FLAT HEAD 4 PCS. 1.9594024 SCREW, HEX, M3X30 FLAT HEAD 4 PCS. 1.9594025 SCREW, HEX, M3X45 FLAT HEAD 4 PCS. 1.9594026 SCREW, HEX, M4X12 FLAT HEAD 4 PCS. 1.9594027 SCREW, HEX, M4X16 FLAT HEAD 4 PCS. 1.9594028 SCREW, HEX, M4X20 FLAT HEAD 4 PCS. 1.9594029 SCREW, HEX, M4X25 FLAT HEAD 4 PCS. 1.9594030 SCREW, HEX, M4X45 FLAT HEAD 4 PCS. 1.9594033 SET SCREW, 3x3mm 4 PCS. 1.9594034 SET SCREW, 4x4mm 4 PCS. 1.9594035 SET SCREW, 3x8mm 4 PCS. 1.9594036 SET SCREW, 5x5mm 4 PCS. 1.9594037 SET SCREW, 5x6mm 4 PCS. 1.9594041 NUT, 3mm NYLOK 4 PCS. 1.9594042 NUT, 4mm NYLOK 4 PCS. 1.9594045 E-CLIPS, MISC SIZES, 8 PCS. 1.9594047 SCREW, HEX, M2.0X6 CAP HEAD 4 PCS. 1.9594049 SCREW, HEX, M2.6X8 CAP HEAD 4 PCS. 1.9594050 SCREW, HEX, M2.6X10 CAP HEAD 4 PCS. 1.9594051 SCREW, HEX, M2.0X6 TAPPING HEAD 4 PCS. 1.9594052 SCREW, HEX, M2.0X6 FLAT HEAD 4 PCS. 1.95

LIFE TIME GUARANTEE HEX WRENCH TOOLS, TIP REPLACEMENTS10813 4 PCS. HEX WRENCH WITH HANDLE, 1.5,2.0,2.5,3.0mm 35.9510814 4 PCS. HEX WRENCH WITH HANDLE, 0.05,1/16,5.64.3.32" 35.9510815 HEX WRENCH WITH HANDLE, 1.5mm (ROSE) 9.9510816 HEX WRENCH WITH HANDLE, 2.0mm (LIME) 9.9510817 HEX WRENCH WITH HANDLE, 2.5mm (D.BLUE) 9.9510818 HEX WRENCH WITH HANDLE, 3.0mm (BLACK) 9.9510819 HEX WRENCH WITH HANDLE, 0.05" (YELLOW) 9.9510820 HEX WRENCH WITH HANDLE, 1/16" (SILVER) 9.9510821 HEX WRENCH WITH HANDLE, 5/64" (RED) 9.9510822 HEX WRENCH WITH HANDLE, 3/32" (PURPLE OR L.BLUE)) 9.9598151 TIP, HEX WRENCH, 1.5mm 5.9598161 TIP, HEX WRENCH, 2.0mm 5.9598171 TIP, HEX WRENCH, 2.5mm 5.9598181 TIP, HEX WRENCH, 3.0mm 5.9598191 TIP, HEX WRENCH, 0.05" 5.9598201 TIP, HEX WRENCH, 1/16" 5.9598211 TIP, HEX WRENCH, 5/64" 5.9598221 TIP, HEX WRENCH, 3/32" 5.95

HEX TOOLS WITH SPECIAL HANDLE AND BITS10823 TOOL SET, 9PC 1/4 DRIVETIPS WITH SILICONE HANDLE 39.9510824 HEX WRENCH SET, 1/4 DRIVE, 1.5,2,2.5,3mm W/O HANDLE 35.9510825 HEX WRENCH WITH HANDLE, 1.5mm (1/4 DRIVE) 9.9510826 HEX WRENCH WITH HANDLE, 2.0mm (1/4 DRIVE) 9.9510827 HEX WRENCH WITH HANDLE, 2.5mm (1/4 DRIVE) 9.9510828 HEX WRENCH WITH HANDLE, 3.0mm (1/4 DRIVE) 9.9510829 HEX WITH HANDLE,SCREWDRIVER, FLAT (1/4 DRIVE) 10.9510830 HEX WITH HANDLE, SCREWDRIVER, PHIL (1/4 DRIVE) 10.9510831 HEX WRENCH WITH HANDLE, 4.5mm NUT(M2.6) DRIVER (1/4 DRIVE) 11.9510832 HEX WRENCH WITH HANDLE, 5.5mm NUT(M3) DRIVER (1/4 DRIVE) 11.95

10833 HEX WRENCH WITH HANDLE, 7mm NUT(M4) DRIVER (1/4 DRIVE) 11.9590824 HANDLE, ALUM. WITH SILICONE (RED WITH BLUE COVER) 7.9590825 TIP, 1/4 HEX WRENCH, 1.5mm 4.9590826 TIP, 1/4 HEX WRENCH, 2.0mm 4.9590827 TIP, 1/4 HEX WRENCH, 2.5mm 4.9590828 TIP, 1/4 HEX WRENCH, 3.0mm 4.9590829 TIP, 1/4 HEX, FLAT SCREWDRIVER 6.9590830 TIP, 1/4 HEX, PHIL SCREWDRIVER 6.9590831 TIP, 1/4 HEX NUT DRIVER, 4.5mm (M2.6NUT) 6.9590832 TIP, 1/4 HEX NUT DRIVER, 5.5mm (M3NUT) 6.9590833 TIP, 1/4 HEX NUT DRIVER, 7mm (M4NUT) 6.9510834 OPEN #REF!10835 OPEN #REF!10836 OPEN #REF!10837 4 PCS. HEX WRENCH W/HANDLE, 1.5,2.0,2.5,3.0mm 37.9510838 HEX WRENCH WITH HANDLE, 1.5mm (SILVER) 9.9510839 HEX WRENCH WITH HANDLE, 2.0mm (YELLOW) 9.9510840 HEX WRENCH WITH HANDLE, 2.5mm (PURPLE) 9.9510841 HEX WRENCH WITH HANDLE, 3.0mm (BLUE) 9.9510842 4 PCS. HEX BALL WRENCH W/HANDLE, 1.5,2.0,2.5,3.0mm 40.9510843 HEX BALL WRENCH WITH HANDLE, 1.5mm (SILVER) 10.9510844 HEX BALL WRENCH WITH HANDLE, 2.0mm (YELLOW) 10.9510845 HEX BALL WRENCH WITH HANDLE, 2.5mm (PURPLE) 10.9510846 HEX BALL WRENCH WITH HANDLE, 3.0mm (BLUE) 10.9510847 SCREWDRIVER WITH HANDLES, 3 PCS. PHILIPS, 00/0/1 SIZES 31.9510848 SCREWDRIVER WITH HANDLE, PHILIPS, 00 SIZE (SILVER) 10.9510849 SCREWDRIVER WITH HANDLE, PHILIPS, 0 SIZE (YELLOW) 10.9510850 SCREWDRIVER WITH HANDLE, PHILIPS, 1 SIZE (BLUE) 10.9590843 TIP, HEX BALL WRENCH, 1.5mm 6.9590844 TIP, HEX BALL WRENCH, 2.0mm 6.9590845 TIP, HEX BALL WRENCH, 2.5mm 6.9590846 TIP, HEX BALL WRENCH, 3.0mm 6.9590847 TIP, HEX, PHILIPS SCREWDRIVER, 00 SIZE 12.9590848 TIP, HEX, PHILIPS SCREWDRIVER, 0 SIZE 12.9590849 TIP, HEX, PHILIPS SCREWDRIVER, 1 SIZE 12.9210851 OPEN 10852 4 PCS. HEX WRENCH W/BLACK HANDLE, 1.5,2.0,2.5,3.0mm 41.9510853 HEX WRENCH WITH BLACK HANDLE, 1.5mm 10.9510854 HEX WRENCH WITH BLACK HANDLE, 2.0mm 10.9510855 HEX WRENCH WITH BLACK HANDLE, 2.5mm 10.9510856 HEX WRENCH WITH BLACK HANDLE, 3.0mm 10.9510857 4 PCS. HEX BALL WRENCH W/BLACK HANDLE, 1.5,2.0,2.5,3.0mm 45.9510858 HEX BALL WRENCH WITH BLACK HANDLE, 1.5mm 11.9510859 HEX BALL WRENCH WITH BLACK HANDLE, 2.0mm 11.9510860 HEX BALL WRENCH WITH BLACK HANDLE, 2.5mm 11.9510861 HEX BALL WRENCH WITH BLACK HANDLE, 3.0mm 11.9510862 SCREWDRIVER WITH BLACK HANDLES, 3 PCS. PHILIPS, 00/0/1 SIZES 31.9510863 SCREWDRIVER WITH BLACK HANDLE, PHILIPS, 00 SIZE (SILVER) 10.9510864 SCREWDRIVER WITH BLACK HANDLE, PHILIPS, 0 SIZE (YELLOW) 10.9510865 SCREWDRIVER WITH BLACK HANDLE, PHILIPS, 1 SIZE (BLUE) 10.9510866 OPEN10867 SCREWDRIVER WITH BLACK HANDLES, 3 PCS. FLAT, 2/3/4SIZES 31.9510868 SCREWDRIVER WITH BLACK HANDLE, FLAT, 2.0 SIZE 10.9510869 SCREWDRIVER WITH BLACK HANDLE, FLAT, 3.0 SIZE 10.9510870 SCREWDRIVER WITH BLACK HANDLE, FLAT, 4.0 SIZE 10.95

STARTER BOXES AND REPLACEMENT PARTS1:8 SCALE BOXES - ON & OFF ROAD TYPE10243 STARTER BOX 1:8, 7.2V PACK TYPE, 775 MOTOR, OFF-ROAD 72.9510250 1:8 STARTER BOX, ON/OFF-ROAD w/ 12V MOTOR 99.9510251 WHEEL, RUBBER, DISC TYPE, REPLACEMENT 4.9510253 1:8 STARTER BOX, OFF/ON-ROAD w/G.PANEL 129.9510255 STARTER BOX, 1:10 & 1:8 NARROW w/ 12V MOTOR & PANEL 119.9510258 STARTER BOX, 1:10 & 1:8 NARROW W/ 12V MOTOR 110.9510248 GRAY/CHROME 1:8 OFF-ROAD STARTER BOX, w/ 2 550 MOTORS 95.9510249 GRAY/CHROME 1:8 OFF-ROAD STARTER BOX, w/ 2 550 MOTORS, GEL CELL, G.PANEL, CABLE 149.95

ULTRA TORSEN - FRONT10620 GREASE, TORSEN GEARS, TEMP GREEN 9.9510621 TORSEN GEAR MODULE, COMPLETE 79.9510649 BEARING 8x19mm, 2 PCS. 7.9510650 TORSEN STEEL COVER, 31mm (NO GEAR SIDE) 12.9510651 TORSEN SHAFT GEARS, LONG & SHORT, 2 PCS. 12.9510652 JOINT CAPS, ULTRA, 2 PCS. 12.9510626 TORSEN CASE (BLACK), 3x25mm SCREWS 7.9510647 TORSEN STEEL CROWN GEAR 31.9510639 TORSEN MISC. PARTS (O-RING.WASHERS) 11.9510648 TORSEN PINION GEAR, 13T 12.95

ULTRA TORSEN - CENTER10620 GREASE, TORSEN GEARS, TEMP GREEN 9.95

10621 TORSEN GEAR MODULE, COMPLETE 79.9510649 BEARING 8x19mm, 2 PCS. 7.9510650 TORSEN STEEL COVER, 31mm (NO GEAR SIDE) 12.9510651 TORSEN SHAFT GEARS, LONG & SHORT, 2 PCS. 12.9510653 FLAT JOINT CAPS 12.9510626 TORSEN CASE (BLACK), 3x25mm SCREWS 7.9510654 TORSEN STEEL SPUR GEAR 31.9510639 TORSEN MISC. PARTS (O-RING.WASHERS) 11.95

FORCE .26 PULL START52019 HEAD, TALL PURPLE, .26 34.9552020 HEAD, BUTTOM REPLACEMENT, .26 19.9552021 HEAD, SHIM, .26 1.9552045 CYLINDER SLEEVE AND PISTON, .26 109.9552060 CONNECTING ROD (ALUM. 7075S) 22.9552074 CRANKCASE, FORCE .25/.26 44.9552273 CRANKSHAFT, SG, PULL START, .25/.26 75.9552090 REAR BACK COVER 6.9552091 REAR BACK PLATE UNIT, PULL START 24.9552098 SPRING AND PIN, PULL START 3.9552099 PULL START UNIT W/ ROPE 24.9552100 CARBURETOR SET PIN 3.9552110 SLIT METAL CONE 2.9552120 DRIVE HUB 3.9552130 CARBURETOR BODY, P4 / P6 11.9552131 CARBURETOR COMPLETE, 7mm 61.9552140 THROTTLE BARREL 6.9552150 THROTTLE NEEDLE 3.9552160 SPRING, THROTTLE NEEDLE 1.9552170 BOOT, THROTTLE 2.5052180 CAP, THROTTLE NEEDLE(OLD) 2.9552181 BALL END, THROTTLE NEEDLE 5.9552190 BARREL STOP BASE AND NUT 2.9552219 BARREL STOP SCREW 2.9552220 LOW END NEEDLE 4.9552230 WASHER, ALUMINUM, 1 PC 0.9552240 FUEL SUPPLY NIPPLE 2.5052250 MAIN NEEDLE SEAT 4.9552260 MAIN NEEDLE 3.9552900 BEARING, OUTSIDE, 607Z 5.9552920 BEARING INSIDE, 13mm 18.9552930 SEAL, REAR COVER 1.9552940 SEAL, CARBURETOR 1.9552950 SEAL, LOW END NEEDLE 0.9552960 SEAL, MAIN NEEDLE 0.9552972 PIN, PISTON, .25/.26 2.9552980 SCREW SET, 8 PCS. 2.5052990 CLIPS, "G", 2 PCS. 1.95

ofna ultra lx comp manual - competitionx.com · 36730 cap joint 94036 5x5mm set screw 30630...

Documents