oil cooler - aoc - total elevator · pdf filepart no. 10248 remote mount direct mount extend...

Part No. 10248 Direct Mount Remote Mount Extend the Life of your Hydraulic Elevator System! Avoid hot oil problems like nuisance shutdowns, leveling problems, and oil odor by installing the MEI AOC Oil Cooler. Benefits • Smoother stops and starts • Extended component life • Fewer shutdowns • Overall performance improvement • Filters oil Recommended Applicaons • Twin jack holeless applicaons with two- or three-stage telescopic jacks. • Heavily used single-stage twin jack holeless projects. • Roped hydraulic applicaons with moderate usage and travel exceeding 25 feet. • Any hydraulic elevator with high usage. Specificaons: • Heat removal: 17,500 BTU/hr @ 40°F temp delta • 3 ⁄4 HP, 115 VAC, 1 phase, 7.2 FLA pump motor or 208-230 VAC, 1 phase, 3.6 FLA pump motor • 1 ⁄4 HP, 115VAC, 1 phase, 3.6 FLA 1900 CFM fan motor or 208-230 VAC, 1 phase, 1.4 FLA 1900 CFM fan motor • 8 GPM, 75 PSI cast iron pump • Weighs approximately 140 lbs • Adjustable thermostat control • 80db at 3 ﬅ. • Electrical requirement, 115 or 208 VAC, 1 phase, 20amp separate circuit • 10 micron filter in hydraulic oil line • Filter head with sight gauge to indicate when the filter needs to be changed • Heavy gauge frame construcon • Includes all fings and hardware needed for adjacent-mount installaon • Includes instrucons for installaon How it Works The Oil Cooler can be mounted to the power unit or located in a remote locaon*. When the oil temperature in the reservoir reaches a preset limit, it is circulated through the radiator. This process reduces the oil temperature by nearly 40°F, depending on site condions. The oil is also filtered as it runs through the system, which results in enhanced performance and extended component life. The filter head has a sight gauge to indicate when the filter needs to be changed. *Remote locaon must be within 110 feet horizontally or 55 feet vercally from the power unit. Piping, wiring, and conduit to remote locaon are not included. • MEI recommends our Cold Weather Kit when your heat exchanger is installed where the temperature gets below 50°F. - Part No. 19919 Overall Dimensions This is MEI’s Standard Oil Cooler MEI-Total Elevator Soluons • 19336 607 th Ave • Mankato, MN 56001 50 Ph: 507-245-3060 • Fax: 507-245-4198 • www.meielevatorsolutions.com Oil Cooler - AOC Air Flow Replaceable Filter

Upload: vandieu

Post on 05-Feb-2018

222 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Part No. 10248

Direct MountRemote Mount

Extend the Life of your Hydraulic Elevator System!Avoid hot oil problems like nuisance shutdowns, leveling problems, and oil odor by installing the MEI AOC Oil Cooler.

Benefits• Smoother stops and starts• Extended component life• Fewer shutdowns • Overall performance improvement• Filters oil

Recommended Applications• Twin jack holeless applications with two- or three-stage telescopic jacks.• Heavily used single-stage twin jack holeless projects.• Roped hydraulic applications with moderate usage and travel exceeding 25 feet.• Any hydraulic elevator with high usage.

Specifications:• Heat removal: 17,500 BTU/hr @ 40°F temp delta• 3⁄4 HP, 115 VAC, 1 phase, 7.2 FLA pump motor

or 208-230 VAC, 1 phase, 3.6 FLA pump motor• 1⁄4 HP, 115VAC, 1 phase, 3.6 FLA 1900 CFM fan motor

or 208-230 VAC, 1 phase, 1.4 FLA 1900 CFM fan motor• 8 GPM, 75 PSI cast iron pump• Weighs approximately 140 lbs• Adjustable thermostat control• 80db at 3 ft.• Electrical requirement, 115 or 208 VAC, 1 phase, 20amp separate circuit• 10 micron filter in hydraulic oil line• Filter head with sight gauge to indicate when the filter needs to be changed• Heavy gauge frame construction• Includes all fittings and hardware needed for adjacent-mount installation• Includes instructions for installation

How it WorksThe Oil Cooler can be mounted to the power unit or located in a remote location*. When the oil temperature in the reservoir reaches a preset limit, it is circulated through the radiator. This process reduces the oil temperature by nearly 40°F, depending on site conditions. The oil is also filtered as it runs through the system, which results in enhanced performance and extended component life. The filter head has a sight gauge to indicate when the filter needs to be changed.

*Remote location must be within 110 feet horizontally or 55 feet vertically from the power unit. Piping, wiring, and conduit to remote location are not included.

• MEI recommends our Cold Weather Kit when your heat exchanger is installed where the temperature gets below 50°F. - Part No. 19919

Overall Dimensions

This is MEI’s Standard Oil Cooler

MEI-TotalElevatorSolutions•19336607thAve•Mankato,MN56001 50 Ph:507-245-3060•Fax:507-245-4198•www.meielevatorsolutions.com

Oil Cooler - AOC

Air Flow

Replaceable Filter

DEPARTMENT OF ADMINISTRATIVE SERVICES · 2009. 8. 7. · Address of Elevator Location Last First Contact Phone Number Elevator Manufacturer Elevator Type Elevator Model Elevator Serial

Elevator Supplier | Elevator Lift Factory | Webstar Elevator

The Perfect Elevator Pitch for Your Elevator PitchPerfect...The Perfect Elevator Pitch for Your Elevator Pitch Ah, the elevator pitch. A favorite tool of the networking masses. A rite

VILLA ELEVATOR - Adm Verticaladmvertical.com/Datasheet/VILLA ELEVATOR v1.0.pdf · · 2017-04-21TRACTION TYPE VILLA ELEVATOR FUJI-YIDA EXPRESS traction type villa elevator applies

01 01 Elevator Technology Elevator Technology iwalk · 01 01 iwalk The easier way. Elevator Technology Elevator Technology thyssenkrupp Elevator AG thyssenkrupp Allee 1 45143 Essen