omega everest manual
TRANSCRIPT
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 1/20
Omega EVERESTTM
3D-Adjustable Sit/Stand Desk System
INSTALLATION MANUALVERSION 1.0
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 2/202
BEFORE YOU BEGINPROVIDED FOR DESK ASSEMBLY:
(1) Allen Key #5
(3) Cable Guide(2) Top Support Arms
(2) Liing legs (Motors are built in)
(2) Feet
(1) Omega Table Top
(8) 20mm round-head
machine screws
(12) 1” fat-head
machine screws
(8) 20mm wood screw(3) ⅝” wood screws
(8) 60mm wood screws
(8) 5mm x 60mm
machine screws(8) 5mm x 20mm
machine screws
(1) Hand Controller Assembly
(4) black ⅝” hex head
machine screws and
(4) silver ⅝” hex head
machine screws
(1) Power Supply &
Power cord
STEP 2
USED WITH YOUR OWN
TABLETOP
STEPS 6 & 8
STEP 4
STEP 10
STEP 6
USED WITH YOUR OWN
TABLETOP
STEP 3
(2) Expandable Crossbars
*ruler in inches & millimeters foryour convenience
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 3/20
CONGRATULATIONS on your purchase o a TermoDeskOMEGA™ adjustable-height desk system! We designedthis product to be as easy as possible to assemble, buti you have any questions during the assembly processplease contact our Customer Care team using theinormation on the back page.
SHOULD you be installing your owntable top on the OMEGA rame, besure to drill pilot holes beore inserting woodscrews. Te wood screws supplied with the OMEGAbase should work with most table tops. It is critical to
pay attention to the available depth or pilot holes so as
not to damage the lamination o the table top surace.
R E A D T H I S :
(1) Keyboard Plaorm Mounng Assembly
(2) Keyboard Plaorm Supports
(2) Carriage bolts
(2) Rubber bumpers
(1) Keyboard Plaorm
(1) Keyboard fence
(6) Spacers
(6) #10 1-1/4” fat head
Phillips screws
(7) #10 5/8” pan head
Phillips screws
(8) M5 20mm pan head
machine screws
PROVIDED FOR KEYBOARD TRAY ASSEMBLY:
STEP 11
STEPS 11 & 14STEP 12
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 4/204
ASSEMBLY INSTRUCTIONS
CLEAR a good-sized area to lay out all componentsand assemble the desk. Lay the table top down on the floor,insert nut side acing up. I not on carpet, we recommendplacing a sof blanket down first in order to protect thetable top surace. Make sure the entire area is clear o anyloose screws or debris, to avoid scratching the laminatedsurace. Alternatively, this can all be done on top o anothertable rather than on the floor. Be careul not to slide thetable top while upside-down, to protect the laminate.
THE OMEGA base is designed to work with any table top,though assembly is easiest when using a genuine OMEGAtable top. OMEGA table tops include threaded insert nuts
that remove any conusion as to where to drill, the bit sizeto use, or how deep to drill. Tese recessed nuts also extendthe lie o the product, by preventing degradation o thewood fibers rom over-tightening and rom removing andreinstalling wood screws too many times.
1SET THE TABLE TOP
FOR THIS STEP:
USING the provided Allen key, attach the eet toeach lifing leg using our (4) 20mm (0.8”) round-headmachine screws or each leg. Note the position o the eetrelative to each leg’s motor housing (see diagram).
2 ATTACH THE FEET TO THE LEGS
FOR THIS STEP:
CAUTION!
MOTORS ARE FACING
EACH OTHER
8x 2x 2x
feetlegs
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 5/20
ATTACH the crossbars to both sides o each motorhousing using the twelve (12) 1” flat-head machine
screws provided. ake care to align the holes properly sothat the screws go in straight. Note: only two o the threeholes need to be used.
3 ATTACH CROSSBARS TO LEGS
FOR THIS STEP:
ATTACH the two support arms to the base, usingour o the eight (8) ⅝” hex-head machine screws provided.
I your base is painted black, use the our (4) black screwsprovided. I painted silver, use the our (4) stainless steelscrews provided. Insert the screws all the way but do not
tighten them down at this point. Make sure the “lip” oeach support arm is acing out rom the base. Note thatthe ELIE base is a cantilevered “C-Leg” design. O theour holes on the top support arm, use only the two holesindicated in the diagram.
4 ATTACH TOP SUPPORT ARMS
FOR THIS STEP:
although there are three hoonly two need to be used fo
proper installation.
OR
12x
4x 2x4x
2x
make sure to align the threeholes of each cross bar to the
three holes of each leg
make sure to align the two holesof each support arm to the two
holes of the leg
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 6/206
PLACE the base down on the table top and lineup the holes in the lef top support arm with the recessednuts in the table top. I your desktop is 48” wide you canproceed to Step 6. IF YOUR desktop is longer than 48” then the next step isto adjust the crossbar width so that the holes in the right
top support arm also line up with the recessed nuts in thetable top.
BEFORE ADJUSTING, mark the center holes o theC-Channel extensions o the crossbars to ensure properadjustment.
TO ADJUST the crossbar width, loosen (do not remove)the two set screws on either side o the center holes o thecrossbars, using the #5 Allen key. Slide the legs apart toreveal the correct number o holes or your table top size,
keeping the unpainted “C channel” tube centered.
FOR EXAMPLE, i installing or a 60” table top, slide theC channel tube so as to expose one additional hole lef-o-
center, and one additional hole right-o-center, to reveal atotal o three holes. Te original exposed hole must remainin the center, with an equal number o newly-exposedholes to the right and lef.*IF YOU DON’T CENTER THE HOLE IN THECENTER POSITION THEN STEP 6 WON’T WORK*
5 ALIGN BASE TO TABLE TOP
FOR THIS STEP:
THE MACHINE screws or attaching the base arelocated in a separate bag rom the base screws.Use the eight (8) 5mm x 60mm machine screws
to attach the crossbars to the table top. Use six (6) 5mm x20mm machine screws to attach the top support arms to
6 AFFIX BASE TO TABLE TOP
8x
FOR THIS STEP:
not provided
the set screws are located onthe inside of the crossbars.
the middle holeon the c channel
extensions shouldremain centeredas you adjust the
legs.
6x
Marker/pen to mark center hole(not provided)
base screws
30” x 48” 1
30” x 60” 3
30” x 72” 7
TABLE TOP SIZE# OF HOLES EXPOSED
IN CROSSBAR
30” x 83” 9
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 7/20
USE the #5 Allen key to tighten the our (4) screwsthat hold the top support arms to the base, and the our (4)set screws on each o the crossbars.
7TIGHTEN ALL SCREWS
FOR THIS STEP:
USING two (2) 5mm x 20mm machine screws,attach the power supply to the table top. Tere are pre-drilled holes or you to align.
8INSTALL POWER SUPPLY
FOR THIS STEP:
these four (4) set screws onthe crossbar are the same
ones from step 5
these four (4) screws onthe arms are the same
ones from step 4
2x
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 8/208
1. PLUG the lef- and right-side drive cables intoany o the three 8-pin motor sockets.
2. PLUG the hand controller into the round 7-pin socket.
3. CONNECT the power supply to the power cable, afer all
other connections.
9 ATTACH CABLES
FOR THIS STEP:
7-pin socket
8-pin motor sockets(use two of three)
1
2 power o
3
POWER SUPPLY LEFT POWER SUPPLY RIGHT
the drive cables are attachedto the motors that are inside
the legs
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 9/20
ALL OMEGA table tops have pre-drilled pilotholes or installing the hand controller on either the lef
r right side. Te 72” and 83” long table tops also havecenter position, ideal or sit-stand-walk treadmill desk
onfigurations.
LIP the sliding plate into the controller with theountersunk holes acing up (you may need to “snap” it in).lip the combined assembly upside down and screw intohe table top using the (3) small wood screws provided.
INSTALL DIGITAL CONTROLLERFOR THIS STEP:
10 3x
SCREWS IN FROM
THE BOTTOM
OF THE HAND
CONTROLLER
ASSEMBLY
+ =
*all omega everest desks comes with anupdated face plate for the hand controller
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 10/2010
mount the digital hand controller wherever you’d
prefer, using the pre-drilled holes provided
TABLETOPS WITH CENTER CUTOUTS HAVE PRE-DRILLED HOLES ON THE LEFT AND RIGHT
ALL TABLETOPS WITH LEFT AND RIGHT CUTOUTS
HAVE PRE-DRILLED HOLES IN THE CENTER
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 11/20
ATTACH the two oot supports to the undersideo the keyboard platorm using three #10 1-1/4” flathead Phillips screws and three spacers per oot support.Position each set o spacers between the oot support andthe underside o the keyboard platorm. DO NOT placewashers between screw head and foot support.
Position the tube assembly by matching the squaremounting plate to the triangular pattern o recessed holesin the center o the underside o the keyboard platorm.Attach the mounting assembly to the underside o thekeyboard platorm using our #10 5/8” pan head Phillips
11 ASSEMBLE KEYBOARD PLATFORM
FOR THIS STEP:
IN ORDER: WASHER, FOOTREST, SCREW
6x2x
6x
4x
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 12/2012
USING eight M5 20mm pan head machinescrews, attach the mounting assembly and platorm tothe underside o the desk. Align the tube assembly bymatching the our holes on each mounting bracket to theour insert nuts on both sides o the Omega cutout.
12 ATTACH KEYBOARD PLATFORM
FOR THIS STEP:
8x
13 CAREFULLY FLIP THE DESK UP
DO NOT drag the tabletop alongside its edges. Doing so
may result in scratches.
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 13/20
TILT the Omega keyboard platorm so that youcan easily access both the top and bottom o the
rear end o the platorm. Using three #10 5/8” pan headPhillips, attach the keyboard ence to the back o theplatorm so that the built-in cable guide is acing up whenthe keyboard platorm is flat.
14 ATTACH KEYBOARD FENCE FOR THIS STEP:
3x
we recommend tilting the
platform up for easier access
align the three holes of the
fence with the three holes on the
bottom of the platform. once
alugned, use the pan-head screws
to attach the two together.
once the fence is attached to the
platform, you’re ready to install
the bumpers!
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 14/2014
AFTER connecting all the cables and testing thatthe desk is working properly, you may want to use the
supplied sel-adhesive cable guides to tidy up the cablesor a cleaner appearance.
16 FINAL TOUCHESFOR THIS STEP:
ATTACH each rubber keyboard bumper tothe keyboard platorm by fitting a carriage bolt
through each o the two slots cut into the platorm so thatthe bolt’s head is flush with the underside o the platorm.Secure each bumper in place by using your hand to twistthe rubber bumper o the bolt over the screw threads.
15 ATTACH RUBBER BUMPERSFOR THIS STEP:
2x 2x
on the bottom of the platform,
put the carriage bolts through
the slots.
twist the rubber bumpers over
the bolts until they are secured
this is what the keyboard
platform should look like from
your perspective after you’re
done.
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 15/20
USER INSTRUCTIONSMAKE sure there is nothing blocking the travel o the desk in the space where it will operate. Afer the desk is assembland plugged into the power outlet, the controller will need to be initialized. o do so, press and hold the “Down” buttuntil the desk descends completely, then “bounces” and ascends slightly. Doing so allows the control unit to register tlowest elevation beore use.
STORING A HEIGHT PRESET
ADJUSTING TO A SAVED POSITION
ADJUST THE DESKTOP TO THE POSITION YOU WANT TO SAVE.
THE DISPLAY WILL SHOW THE DESKTOP HEIGHT.
PRESS THE MEMORY KEY.
THE DISPLAY WILL READ S .
PRESS THE DESIRED MEMORY POSITION KEY E.G. 1.
THE DISPLAY WILL READ S 2. THE SET DESKTOP POSITION WILL NOW BE
SAVED TO THE SELECTED MEMORY POSITION KEY.
YOU WILL HEAR AN AUDIBLE DOUBLE CLICK AND AFTER ABOUT 2 SECONDS
THE SAVED DESKTOP POSITION WILL BE DISPLAYED.
PRESS the desired memory position key (e.g. 2) and hold it down. Te desktopwill move until it reaches the saved position. I you release the key beore the savedposition is reached, the desktop will stop and the saved desktop position will notbe reached.
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 16/2016
MANUAL RESET
CONTAINER- AND SHELF-STOP POSITIONS
IF THE actual desktop position no longer corresponds to the height displayed, you can reset the lowest desktop positito the minimum height.
PRESS and hold the desktop down key until the desktop has reached the lowest position(programmed desktop position).
PRESS and hold the desktop down key again. Afer about 5 seconds, the desktop willslowly move urther down until it reaches the absolute lowest desktop position possible(22 inches).RELEASE the desktop down key. Te electric height-adjustable desk can again be usednormally.
NOTE: Te Container- and Shel Stop Positions eature is not enabled during reset. Ensure that the area below the deis completely clear beore perorming a reset.
THESE TWO eatures can be used to limit the movement area o the desktop (e.g. i a tall trash can is placed underneathe desktop). A container stop position can be defined in the lower hal o the movement area, a shel stop positionthe upper hal. I a container stop position is set, this position will be the lower limit position. I a shel stop positionset, this position will be the new upper limit position.
MOVE the desktop to a position where the container stop or shel stop position shall
be stored.PRESS S or 10 seconds. Te Control Unit will click twice when the container stopposition is stored.
TO STORE A CONTAINER STOP / SHELF STOP POSITION:
MOVE the desktop to any position in the lower hal to deactivate the container stop.Move the desktop to any position in the upper hal to deactivate the shel stop.PRESS S or 10 seconds. Te Control Unit will click once when the container or shel stopposition is deactivated.
TO DEACTIVATE THE CONTAINER STOP / SHELF STOP POSITION:
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 17/20
TROUBLESHOOTINGIF THE table cannot be raised or lowered, check the cable connection between the control unit and the motor units (system), the handset and the control unit, as well as between the control unit and the power outlet.
IF THE table still does not respond, the control unit may have triggered the overheating protection or the intermittenprotection. Please wait or at least nine minutes and try again beore proceeding with other measures.
IF THE control unit has been replaced - or unplugged or a substantial period o time - it must first be reset beore it cbe used:
1. LOWER the table to its lowest position by holding the “Down” button on the handset.2. PRESS the “Down” button on the handset again and hold it down until the table first movesractions o an inch downwards and then ractions o an inch back up again. Te control unithas now registered the lowest elevation and is ready to use.3. SHOULD the table still not work as intended afer taking these measures, please contact theiMovR Customer Care Department or assistance.
THE OMEGA Keyboard Platorm can be set to one o two height positions. By deault, the bar assembly arrives setthe lower position. You can adjust the bar assembly higher by removing the two hex screws rom both ends o the piv
bar, and reattaching the bar by inserting those same hex screws through the upper set o holes on the bracket.
o adjust the Omega Keyboard Platorm, simply loosen the central clamp by twisting the rubberized kncounterclockwise. Ten push down on the rear end o the platorm or a steeper angle or push up rom the bottom o platorm or a shallower angle. Once you have the platorm set to the desired position, secure it in place by tightenithe rubberized knob by twisting it clockwise.
Depending on the depth and shape o your keyboard you may want to adjust the rubber bumpers orward or back. do this, simply loosen the rubber bumper, slide it to the desired location, and retighten.
USING THE OMEGA KEYBOARDPLATFORM
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 18/2018
OPTIONAL ACCESSORIES
PREVENTATIVE MAINTENANCEAND CLEANINGAFTER first week o use: ighten down all screws and bolts.
CLEANING the base: Clean the base rame by wiping it down with a microfiber cloth moistened with a standahousehold cleaning solution. Never use solvents or abrasive or corrosive compounds on the rame. Te base shouldcleaned at regular intervals to remove dust and dirt, and inspected or mechanical damage, wear and breaks - worn oparts should be replaced.
CLEANING the table top: All TermoDesk table tops are manuactured with a “3D lamination” process that resultsan extremely durable surace, similar to what is ofen used in hospital environments. As such it can stand up to mcleaning solutions without risk o discoloration or degradation. Anti-bacterial solutions may be used. Always test ncleaning solutions on a less-seen surace first beore using on the entire table top.
EXTENDED non-use: Unplug the power cord i you do not intend to use the desk or a long period o time.
1 2 3
THERMODESK INSURFACE DUALAC POWER SOCKET
THE 3” grommet holes provided in the ELIE table topsare ideally sized or accepting the flush-mounted powersocket “nodes.”
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 19/20
WARRANTYTHE OMEGA EVEREST warranty coverage includes 20 years on the steel rame, 10 years on moving parts, 5 years table tops, and 2 years on the electronics. Te ollowing limitations apply:
THIS WARRANTY only covers deects as specified herein and does not include deects or damages attributable improper installation, misuse or normal surace weathering, or deects or damages caused by accidents or fire or oth
casualty or Acts o God, or any other causes or occurrences beyond the manuacturer’s control. Te exclusive remedaction provided or the customer hereunder shall be repair, restoration or replacement o the components as are outo be deective.
TABLE TOP: Te replacement o new materials or those as may be deective may result in a color variance in comparisto the originally installed laminates due to slight color or texture changes by laminate manuacturers and is not indicato a deect. iMovR reserves the right to substitute such laminates as are then being manuactured and is only obligatto match color and quality with such products as it is manuacturing at the time o replacement.Electric base rame: New base rames may have paint deects or scratches on components that are hidden beneath surace o the desk, which are normal. Painted components that are normally visible to sitting or standing users afinstallation o the table top, that arrive in damaged condition, will be replaced under this warranty i iMovR is notifi
beore the component is installed.
THIS WARRANTY is limited to repair, restoration and/or replacement by iMovR o any deective unit provided manuacturer: (a) receives a written, axed or emailed notice o claim under this warranty, including sufficiently hresolution photographs that clearly show the nature o the damage, and (b) within 30 days afer notice o claim, isreceipt o the deective unit at its place o business, unless this requirement is waived by iMovR. Te manuacturer warrange or retrieval o the deective product via its carrier-o-choice. In some cases the manuacturer may elect notretrieve the deective component, and may opt to send a replacement product based only on photographic evidencewarrantied deects. I upon receipt and inspection o the returned component it is determined that the damage was ndue to a manuacturing flaw but rather one o the exempted reasons stated above, the costs o shipping the units to arom the manuacturer, plus the cost o the replacement component, shall be charged back to the customer.
LIMITATION OF LIABILITY: I IS UNDERSOOD AND AGREED HA MANUFACURER’S LIABILIWHEHER IN CONRAC, IN OR UNDER ANY WARRANY, IN NEGLIGENCE OR OHERWISE, SHANO EXCEED HE REURN OF HE AMOUN OF PURCHASE PRICE FOR HE DEFECIVE IEM PAID PURCHASER AND UNDER NO CIRCUMSANCES SHALL SELLER BE LIABLE FOR SPECIAL, INDIREC OCONSEQUENIAL DAMAGES. NO ACION, REGARDLESS OF FORM, ARISING OU OF HE RANSACIOUNDER HIS AGREEMEN MAY BE BROUGH BY HE PURCHASER MORE HAN ONE YEAR AFER HCAUSE OF ACION HAS ACCRUED.
SOME states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusior limitation o incidental or consequential damages, so the above limitations or exclusions herein may not apply to y
Tis warranty gives you specific legal rights, and you may also have other rights, which vary, rom state to state.
TO OBTAIN warranty repair please contact the iMovR Customer Care department with the contact inormation onthe back page.
7/26/2019 Omega Everest Manual
http://slidepdf.com/reader/full/omega-everest-manual 20/20
SPECIFICATIONS
LIFT CAPACTIY: 220 lbs.
NOISE LEVEL: 42 dB during descent, 46 dB during ascent
HEIGHT ADJUSTMENT RANGE: 23.5” to 48.5” (ELIE X: 26” to 51.7”)
WIDTH ADJUSTMENT RANGE: 44” to 75” — eight incremental positions
TRAVEL SPEED: 1.5 inches-per-second
CONTROLLER: Four pre-programmable positions, displays height in inches
MANUFACTURING ORIGIN: Made in America, incorporating precision BOSCH motors rom Germ
LAMINATION TYPE: Sur(x) 3D
AVAILABLE SIZES: 30” x 48” | 30” x 60” | 30” x 72” | 30” x 83”
C O N T A C T : iMovR
HOURS:PHONE:FAX:EMAIL:LIVE CHAT:
See www.iMovr.com/hours(888) 208-6770 or (425) 999-3550(425) [email protected]
AVAILABLE OPTIONS FROM iMovR
Stowaway Ergonomic Keyboard ray
Single and Dual-Arm LCD Monitor Stands
Grommet-mounted Dual-AC Power Socket
shown here with a walking treadmill. any brand ofwalking treadmill may be used with the elite desk.
EVEREST BASE:
EVEREST TABLE:
POWER CONSUMPTION: 0.375 watts on standby; 2.8A on start-up; 1.4A on continuous lif
ANTICOLLISION DETECTION: Programmable container-stop and shel-stop positions
SURFACE RATING: Ultra-durable
EDGING: Ergonomically-contoured “comort edge”
MANUFACTURING ORIGIN: Made in Michigan, USA
EASY INSTALLATION FEATURES: Recessed nuts or attaching base legs, pre-drilled holes pilotholes or keyboard tray(s) and hand controller