operation manual sd-cx1h - minidisc

1-BIT DIGITAL AUDIO SYSTEM

SD-CX1HOPERATION MANUAL

2

CX1H_UK02-10.fm00/12/17

Impo

rtan

t Ins

truc

tion

Spe

cial

Not

es

Special Notes

NOTES FOR USERS IN THE U.K. AND IRELAND

The mains lead of this product is fitted with a non-rewireable (moulded)plug incorporating a 3A fuse. Should the fuse need to be replaced, a BSIor ASTA approved BS 1362 fuse marked or and of the same rating asabove, which is also indicated on the pin face of the plug must be used.

Always refit the fuse cover after replacing the fuse. Never use the plugwithout the fuse cover fitted.

In the unlikely event of the socket outlet in your home not being compat-ible with the plug supplied, cut-off the mains plug and fit an appropriatetype.

DANGER:The fuse from the cut-off plug should be removed and the cut-off plugdestroyed immediately and disposed of in a safe manner.

Under no circumstances should the cut-off plug be inserted elsewhereinto a 13A socket outlet as a serious electric shock may occur.To fit an appropriate plug to the mains lead, follow the instructions below:

IMPORTANT:The wires in the mains lead are coloured in accordance with the followingcode:Blue : NeutralBrown : Live

As the colours of the wires in the mains lead of this product may notcorrespond with the coloured markings identifying the terminals in yourplug, proceed as follows:● The wire which is coloured blue must be connected to the plug terminal

which is marked N or coloured black.● The wire which is coloured brown must be connected to the plug termi-

nal which is marked L or coloured red.

Ensure that neither the brown nor the blue wire is connected to the earthterminal in your three pin plug.

Before replacing the plug cover, make sure that:● If the new fitted plug contains a fuse, its value is the same as that

removed from the cut-off plug.● The cord grip is clamped over the sheath of the mains lead and not

simply over the lead wires.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

SERVICE INFORMATIONIn the unlikely event of your equipment requiring repair, please contactthe dealer or supplier from whom it was purchased. Where this is notpossible, please visit our web-site www.sharp.co.uk/support.Customers without internet access may telephone 08705 274277 dur-ing office hours (or (01) 676 0648 if telephoning from lreland).Please note; all calls will be charged at local rate.

Certain replacement parts and accessories may be obtained from ourmain parts distributor.

WILLOW VALE ELECTRONICS LTD.0121 766 5414

In the unlikely event of this equipment requiring repair during the guaran-tee period, you will need to provide proof of the date of purchase to therepairing company.Please keep your invoice or receipt, which is supplied at the time of pur-chase.

0012

Web-site: www.sharp.co.uk/support Help Line: 08705 274277 (office hours)

3

CX1H_UK02-10.fm00/12/17

Impo

rtan

t Ins

truc

tion

Spe

cial

Not

es

� WARNING� When the ON/STAND-BY button is set at STAND-BY position, mains voltage is still

present inside the unit. When the ON/STAND-BY button is set at STAND-BY posi-tion and the clock is displayed, the unit may be brought into operation by the timermode or remote control.

� This unit contains no user serviceable parts. Never remove covers unless qualifiedto do so. This unit contains dangerous voltages, always remove mains plug fromthe socket before any service operation and when not in use for a long period.

� To prevent fire or shock hazard, do not expose this appliance to dripping or splash-ing. No objects filled with liquids, such as vases, shall be placed on the apparatus.

� CAUTION� Use of controls, adjustments or performance of procedures other than those spec-

ified herein may result in hazardous radiation exposure.

� As the laser beam used in this compact disc player is harmful to the eyes, do notattempt to disassemble the cabinet. Refer servicing to qualified personnel only.

� NOTES� Recording and playback of any material may require consent, which SHARP is

unable to give. Please refer particularly to the provisions of the Copyright Act1956, the Dramatic and Musical Performers Protection Act 1958, the PerformersProtection Acts 1963 and 1972 and to any subsequent statutory enactments andorders.

� This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/EEC.

� US and foreign patents licensed from Dolby Laboratories.

� The letters in brackets contained in the model number indicate the colour of theproduct only. Operation and specifications are unaffected.

� SD-CX1H 1-Bit Digital Audio System of SD-CX1H (main unit) and CP-CX1H(speaker system).

If you require any advice or assistance regarding your Sharp product, please visit our web-site www.sharp.co.uk/support. Customers without internet access may telephone 08705 274277 during office hours (or (01) 676 0648 if telephoning from Ireland).


4

CX1H_UK02-10.fm00/12/17

Impo

rtan

t Ins

truc

tion

Con

tent

s

IntroductionThank you for purchasing this SHARP product. To obtain the best performance fromthis product, please read this manual carefully. It will guide you in operating yourSHARP product.

ContentsPage

� Important InstructionSpecial Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 3

� General InformationPrecautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 10

� Preparation for UseRemote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11System Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 14

� Basic OperationGeneral Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Sound Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

� CD PlaybackListening to a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 - 20

� MD PlaybackListening to a MiniDisc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 - 23

� Advanced CD/MD PlaybackDirect Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Repeat or Random Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Programmed Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Page

� RadioListening to the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 - 27

� RDS RadioUsing the Radio Data System (RDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 - 34

� MD RecordingBefore Recording to a MiniDisc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Recording to a MiniDisc from a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 - 39Recording to a MiniDisc from the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Checking Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

� MD EditingTitling a MiniDisc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 - 44Editing a Recorded MiniDisc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 - 48

� Advanced FeaturesTimer and Sleep Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 - 53Enhancing Your Stereo System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 - 55

� ReferencesWhat is a MiniDisc? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56MiniDisc System Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 - 59Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 - 61

TERMS OF GUARANTEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back cover


5

CX1H_UK02-10.fm00/12/17

Gen

eral

Info

rmat

ion

Pre

caut

ions

Precautions� General� Please ensure that the equipment is positioned in a well-ventilated area and

ensure that there is at least 10 cm (4") of free space along the sides, top and backof the equipment.

� Do not place anything on top of the unit.

� Do not expose the unit to moisture, to temperatures higher than 60°C (140°F) or toextremely low temperatures.

� If your system does not work properly, disconnect the AC power lead from the wallsocket. Plug the AC power lead back in, and then turn on your system.

� No naked flame sources, such as lighted candles, should be placed on the appa-ratus.

� Attention should be drawn to the environmental aspects of battery disposal.� The apparatus is designed for use in moderate climate.� This unit should only be used within the range of 5°C - 35°C (41°F - 95°F).

� Use the unit on a firm, level surface free from vibration.

� Keep the unit away from direct sunlight, strong magnetic fields, excessive dust, humidity and electronic/electrical equipment (home comput-ers, facsimiles, etc.) which generates electrical noise.

10 cm (4") 10 cm (4")

10 cm (4")

10 cm (4")

� In case of an electrical storm, unplug the unit for safety.

� Hold the AC power plug by the head when removing it from the wall socket, as pulling the lead can dam-age internal wires.

� Do not remove the outer cover, as this may result in electric shock. Refer internal service to your local SHARP service facility.

� The ventilation should not be impeded by covering the ventilation openings with items, such as newspa-pers, tablecloths, curtains, etc.


6

CX1H_UK02-10.fm00/12/17

Gen

eral

Info

rmat

ion

Pre

caut

ions

/ A

cces

sorie

s

Precautions (continued)

Warning:� The voltage used must be the same as that specified on this unit. Using this prod-

uct with a higher voltage other than that which is specified is dangerous and mayresult in a fire or other type of accident causing damage. SHARP will not be heldresponsible for any damage resulting from use of this unit with a voltage other thanthat which is specified.

� CD players use a laser pickup which can damage the eyes if viewed directly. Do

not look at the pickup, and do not touch the pickup directly. � This product is equipped with a cooling fan on its back for better heat radiation.

� Volume controlThe sound level at a given volume setting depends on speaker efficiency, location,and various other factors. It is advisable to avoid exposure to high volume levels,which occurs whilst turning the unit on with the volume control setting up high, orwhilst continually listening at high volumes.

� Care of compact discsCompact discs are fairly resistant to damage, however mistracking can occur due to anaccumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoy-ment from your CD collection and player.� Do not write on either side of the disc, particularly the non-label side from which signals

are read. Do not mark this surface.� Keep your discs away from direct sunlight, heat, and excessive moisture.� Always hold the CDs by the edges. Fingerprints, dirt, or water on the CDs can cause

noise or mistracking. If a CD is dirty or does not play properly, clean it with a soft, drycloth, wiping straight out from the centre, along the radius.

Accessories Please confirm that the following accessories are included.

Note:Only the above accessories are included.

Remote control 1 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar) 2

AM loop aerial 1 FM aerial 1

Speaker wire 2 AC power lead 1

Non-slip sheet for speakers 8


7

CX1H_UK02-10.fm00/12/17

Gen

eral

Info

rmat

ion

Con

trols

and

Indi

cato

rs

Controls and Indicators� Front panel

Reference page1. CD Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182. CD Cover Open/Close Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183. Remote Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114. Function Indicator 5. Timer Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506. On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187. MD Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218. MD Eject Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229. MD Record Mode Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

10.CD/MD Play Mode Select Button . . . . . . . . . . . . . . . . . . . . . . . . . . . 2411.MD Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2212.MD Play/Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2113.CD Stop Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1814.CD Play/Pause Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1815.Volume Up or Down Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1616.Headphone Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5417.Erase Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4818.MD Record Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3919.Auxiliary/Demo Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14, 5520.Tuner (Band) Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2621.CD/MD Fast Reverse, Tuning Down Button . . . . . . . . . . . . 19, 22, 2622.MD +10 Track Up Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2223.CD/MD Fast Forward, Tuning Up Button . . . . . . . . . . . . . . . 19, 22, 26

1

23

4

5

6 7 8 9 10 12 13 14 15

16 17 18 19 20 21

11

22 23


8

CX1H_UK02-10.fm00/12/17

Gen

eral

Info

rmat

ion

Con

trols

and

Indi

cato

rs

Controls and Indicators (continued)

� Multi-function LCD display1. Level Meter/Character Information/Frequency Indicator2. Band Selector Indicator3. Record Indicator4. CD/MD Play Indicator5. Top Position Indicator6. Record Mode Indicator7. RDS Indicator8. Traffic Programme Indicator9. Traffic Announcement Indicator

10.MD Record Pause Indicator11.Dynamic PTY Indicator12.CD/MD Repeat Indicator13.EON Indicator14.Programme Type Indicator15.Traffic Information Indicator16.Surround Indicator17.Random Play Indicator18.Programme Play Indicator19.Sound Synchronised Recording Indicator20.Track Edit Indicator21.TOC Indicator22.FM Stereo Indicator23.FM Stereo Mode Indicator24.Sleep Indicator25.Timer Play/Recording Indicator

2

1

34

65

7 8 9 1110 12 13 14 15

17

19 20 21

2223

24

25

16

18


9

CX1H_UK02-10.fm00/12/17

Gen

eral

Info

rmat

ion

Con

trols

and

Indi

cato

rs

� Rear panel

Reference page1. Cooling Fan 2. Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133. FM 75 Ohms Aerial Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134. Aerial Earth Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135. AM Loop Aerial Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136. AC Input Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127. Auxiliary Input Sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

� Speaker system1. Speaker Grille2. Tweeter3. Woofer4. Bass Reflex Duct5. Speaker Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Placing the speaker system:There is no distinction between the right and the left speakers. Speaker grilles are removable:Make sure nothing comes into contact with the speaker diaphragms when youremove the speaker grilles.

The arrow on the back of the net must face upward.

1 2

6 7

3

4

5

2

3

45

1


10

CX1H_UK02-10.fm00/12/17

Gen

eral

Info

rmat

ion

Con

trols

and

Indi

cato

rs

Controls and Indicators (continued)

� Remote controlReference page

1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112. CD/MD Play Mode Select Button 3. MD Record Mode Button 4. On/Stand-by Button 5. MD Record Button 6. Top Position Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .397. Track Edit Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .388. Sound Synchronise Record Button . . . . . . . . . . . . . . . . . . . . . . . .559. RDS EON Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28, 32

10.RDS Programme Type/Traffic Information Search Button . . . .28, 3111.RDS ASPM (Auto Station Programme Memory) Button . . . . . . . . .2812.Volume Up or Down Button 13.CD/MD Fast Reverse, Tuning Down Button 14.Extra Bass Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1615.CD/MD Programme Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2516.Clear Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2517.Name/TOC-Edit Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4218.Timer/Delete Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17, 4919.Time Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20, 2320.Enter Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1721.MD Stop Button 22.MD Play/Pause Button 23.CD Stop Button 24.CD Play/Pause Button 25.Tuner (Band) Button 26.Auxiliary Button 27.Surround Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1628.CD/MD Fast Forward, Tuning Up Button 29.Preset Equalizer Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1630.Character Input/CD, MD, Tuner Direct Buttons . . . . . . . . . . . . .24, 4231.Display Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20, 2332.Recording Level/Cursor/Tuner Preset Button . . . . . . . . . . .26, 39, 4233.CD/MD Edit Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

123456789

1011121314151617181920

****

* *

* * * * * * *

212223242526272829

30

313233

*

*

*

***

Buttons with "*" mark in the illustration can be operated on the remote control only. Other buttons can be operated both the main unit and the remote control.


11

CX1H_UK11-16.fm00/12/17

Pre

para

tion

for

Use

Rem

ote

Con

trol

Remote Control� Battery installation1 Open the battery cover.

2 Insert the supplied batteries according to the direction indicated inthe battery compartment.

� When inserting or removing the batteries, push them towards the battery termi-nals.

3 Close the battery cover.

Precautions for battery use:� Replace all old batteries with new ones at the same time.� Do not mix old and new batteries.� Remove the batteries if the unit will not be used for long periods of time. This will

prevent potential damage due to battery leakage.

Caution:� Do not use rechargeable batteries (nickel-cadmium battery, etc.).� Installing the batteries incorrectly may cause the unit to malfunction. Notes concerning use:� Replace the batteries if the operating distance is reduced or if the operation

becomes erratic. Purchase 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).� Periodically clean the transmitter on the remote control and the sensor on the

stereo system with a soft cloth.� Exposing the sensor on the stereo system to strong light may interfere with opera-

tion. Change the lighting or the direction of the stereo system.� Keep the remote control away from moisture, heat, shock, and vibrations.

� Test of the remote controlCheck the remote control after checking all connections have been made correctly.(See pages 12 - 14.)Face the remote control directly to the remote sensor on the unit.

The remote control can be used within the range shown below:Press the ON/STAND-BY button. Does the power turn on? Now, you can enjoy themusic.

Remote sensor

0.2 m - 6 m(8" - 20')


12

CX1H_UK11-16.fm00/12/17

Pre

para

tion

for

Use

Sys

tem

Con

nect

ions

System Connections

Wall socket(AC 230V, 50 Hz)

FM aerial

Left speaker

Right speaker

AM loop aerial


13

CX1H_UK11-16.fm00/12/17

Pre

para

tion

for

Use

Sys

tem

Con

nect

ions

� Aerial connectionSupplied FM aerial:

Supplied AM loop aerial:

Note:Placing the aerial on the stereo system or near the AC power lead and speaker wiresmay cause noise pickup. Place the aerial away from the stereo system for betterreception.

Installing the AM loop aerial:

� External FM or AM aerialUse an external FM or AM aerial if you require better reception. Consult your dealer.

Notes:� When an external FM aerial is used, disconnect the supplied FM aerial wire from the FM

75 OHMS socket.� When using an external AM aerial, be sure to keep the wire of the AM loop aerial con-

nected.

� Speaker connectionConnect the wire with the black line to the (-) and transparent one to the (+) .

Caution:� Connect the speaker wires to the speakers first, then to the unit.� Use speakers with an impedance of 6 ohms or more, as lower impedance speak-

ers can damage the unit.� Do not mistake the right and the left channels. The right speaker is the one on the

right side when you face the unit.� Do not let the bare speaker wires touch each other.

� Do not stand or sit on the speakers. You may be injured.

Connect the FM aerial wire to the FM 75 OHMS socket and position the FM aerial wire in the di-rection where the strongest signal can be re-ceived.

Connect the AM loop aerial wire to the AM and GND terminals. Position the AM loop aerial for optimum re-ception. Place the AM loop aerial on a shelf, etc., or attach it to a stand or a wall with screws (not supplied).

< Assembling > < Attaching to the wall >

White

Black

WallScrews

AM loop aerial 15 m (49 feet)

7.5 m(25 feet)

External AM aerial

Earth rod

External FM aerial

21 3

Left speaker

Clear

Black line

Right speaker


14

CX1H_UK11-16.fm00/12/17

Pre

para

tion

for

Use

Sys

tem

Con

nect

ions

System Connections (continued)

� To mount the speakers on the wallThe design of the speakers allows them to be hung on the wall. Be sure to use the type andsize of screw that is shown below.

1 Make a hole in the wall using a drill.

2 Drive a wall mount plug into the hole using a hammer. Drive thewall mount plug in until it is flush with the wall surface.

3 Drive one screw into the wall for each speaker as shown in theillustration.

� Drive the screws, so there is about a 5 mm (3/16") space between the wall and thehead of the screw.

4 Mount the speaker on the wall so that the screw head is insertedinto the slot on the speaker.

� How to apply non-slip sheets

� Connecting the AC power leadAfter checking all the connections have been made correctly, plug the unit into themains. If you plug the unit first, the unit will enter the demonstration mode.

Note:Unplug the unit if it will not be used for a prolonged period of time.

� Demonstration modeThe first time the unit is plugged in, the unit will enter the demonstration mode. Youwill see words scroll.

To cancel the demonstration mode:When the unit is in the power stand-by mode (demonstration mode), press the AUX(DEMO) button. The unit will enter the low power consumption mode.

To return to the demonstration mode:When the unit is in the power stand-by mode, press the AUX (DEMO) button again.

32 mm(1-1/4")

8-9 mm (3/8")

3.2 mm (1/8")

9 mm (3/8")

5 mm(3/16")

Min.22 mm (7/8")

Wall surface Wall mounting screw

Wall surface

Adhere the non-slip sheets to the bottom of the speaker.

Adhere the non-slip sheets on the lower back of the speaker, and then mount it to the wall.


15

CX1H_UK11-16.fm00/12/17

Bas

ic O

pera

tion

Gen

eral

Con

trol

General Control� You can select and change to the colour

you like from 7 different colours.

� To change the display illumination bright-ness

To dim:

To brighten:

1 Press the ON/STAND-BY button to turn the power on.

2 Press the DISPLAY button for 2 seconds or more.

3 Press the REC LEVEL/CURSOR or button to select "COLOR".

4 Press the ENTER button.

5 Press the REC LEVEL/CURSOR or button.

INITIAL The colour changes automatically along with the operation.

FIXED You can select a colour you like.

DAILY The colour changes according to the day of the week.

RANDOM The colour changes at random.


7 When FIXED or DAILY is selected:

� Press ENTER button after selecting your favourite colour with the REC LEV-EL/CURSOR or button.

� You can select the colour you like from 7 colours (COLOR 1 to COLOR 7).


2 Hold the DISPLAY button down for 2 seconds or more.

3 Press the REC LEVEL/CURSOR or button to select "DIMMER ON ?".


� The light goes out and characters are dimmed.

1 Hold the DISPLAY button down for 2 seconds or more.



16

CX1H_UK11-16.fm00/12/17

Bas

ic O

pera

tion

Sou

nd C

ontro

l

Sound Control� Volume controlPress the VOLUME button to increase the volume and the VOLUME button fordecreasing.

� Bass controlWhen the X-BASS button is pressed, the unit will enter the extra bass mode whichemphasises the bass frequencies. To cancel the extra bass mode, press the X-BASSbutton.

� SurroundPress the SURROUND button to allow you to enjoy music that seems to surround you."SURROUND" will appear.Press the SURROUND button again to cancel the surround mode."SURROUND" will go out.

� EqualizerPress the PASS/EQ button repeatedly until the desired sound mode appears.

Bass is emphasised. Cancelled.

Bass and treble are emphasised.The sound is not modified.

Vocals (midrange tones) are emphasised.

Treble is reduced.


17

CX1H_UK17-25.fm00/12/17

Bas

ic O

pera

tion

Set

ting

the

Clo

ck

Setting the Clock

In this example, the clock is set for 9:30 15. 02 '01 .

To confirm the time display:[When the unit is in the stand-by mode]Press the DISPLAY button on the remote control.The time display will appear for about 5 seconds.[When the power is on]Press the TIMER/DELETE button.Within 10 seconds, press the REC LEVEL/CURSOR or button.The time display will appear for about 10 seconds. Note:The clock setting will be cleared when the unit is unplugged or the power failureoccurs. To reset the clock:Perform "Setting the Clock" from the beginning.


2 Press the TIMER/DELETE button.

3 Within 10 seconds, press the REC LEVEL/CURSOR or button toselect the "TIME ADJUST".

4 Within 10 seconds, press the ENTER button.

5 Press the REC LEVEL/CURSOR or button to adjust the year,and then press the ENTER button.

6 Press the REC LEVEL/CURSOR or button to adjust the month,and then press the ENTER button.

7 Press the REC LEVEL/CURSOR or button to adjust the date,and then press the ENTER button.

8 Press the REC LEVEL/CURSOR or button to adjust the hour,and then press the ENTER button.

9 Press the REC LEVEL/CURSOR or button to adjust the minutes,and then press the ENTER button.

� The hour will not advance even if minutes advance from "59" to "00".

� The clock starts from "0" second. (Seconds are not displayed.) The time display will disappear after a few seconds.


18

CX1H_UK17-25.fm00/12/17

CD

Pla

ybac

kLi

sten

ing

to a

CD

Listening to a CD

To interrupt playback:Press the CD button.To resume playback from the same point, press the CD button again.

To stop playback:Press the CD button.

Load a CD firmly with the label side facing toward you.


2 Press the CD button.

3 Press the CD button to open the CD cover.

4 Set a CD and press the CD button.

Total number of tracks Total playing time

5 Press the CD button to start playback.

� When the last track has finished playing, the CD player will stop automatically.


19

CX1H_UK17-25.fm00/12/17

CD

Pla

ybac

kLi

sten

ing

to a

CD

To remove the CD:Whilst in the stop mode, press the CD button.Press the CD eject button and remove the CD.

After use:� Press the CD button and close the CD cover.� When the unit enters the stand-by mode, the opened CD cover will be closed auto-

matically.

Caution:� Be careful not to jam your fingers with the CD cover when opening and clos-

ing it.� Do not stop or move the CD cover manually. It may cause malfunctions to

the unit.� Keep foreign objects out of the CD compartment.� Subjecting the unit to shock or vibration may cause mistracking.� When the unit is not being used, be sure to close the CD cover. If it is left open, the

lens may be covered with dust and the unit may not function properly.� Playing certain compact discs at a high volume may cause mistracking. In this

case, listen at a lower volume.� If TV or radio interference occurs during CD operation, move the unit away from

the TV or radio.� If an error message is displayed during CD operation, see "Error Messages" on

page 57.

� To locate the beginning of a track

� To locate the desired portion

Notes:� Normal playback will resume when the or button is released.� When the end of the last track is reached during fast forward, "END" will appear in

the display and CD operation will be paused. When the beginning of the first trackis reached during fast reverse, the unit will enter the playback mode.

CD Eject Button

To move to the beginning of the next track:

Press the button during playback.

� You can skip to any track by pressing the button repeatedly until the desired track number appears.

To restart the track being played:



For audible fast forward:

Press and hold down the button during playback.

For audible fast reverse:



20

CX1H_UK17-25.fm00/12/17

CD

Pla

ybac

kLi

sten

ing

to a

CD

Listening to a CD (continued)

� Switching the time display Each time the TIME button on the remote control is pressed during playback, the dis-play will change.

Notes:� During random play, the total remaining playing time will not be displayed.� Depending on the CD, the playing time display may not match the total playing

time which is indicated on the CD jacket, as the time between tracks is notincluded.

� Switching to the level meterEach time the DISPLAY button on the remote control is pressed during playback, thedisplay will change.

The elapsed playing time for the current track will be displayed.

The remaining playing time for the current track will be displayed.

The total remaining playing time for the disc will be displayed.


The level meter will be displayed.


21

CX1H_UK17-25.fm00/12/17

MD

Pla

ybac

kLi

sten

ing

to a

Min

iDis

c

Listening to a MiniDiscA track can be played in the mode it is recorded: monaural or 2 times or 4 times longrecording (stereo) mode.

1 Open the control panel cover.

Control panel cover


3 Press the MD button.

4 Load a MiniDisc into the MD compartment, label side up.

Disc name Total number of tracks

Total playing time

� If the MiniDisc is loaded in a wrong way, "? MD DISC" or "Can't READ" appears on the display. In that case, press the MD button.

� The disc name will be displayed only when it has been programmed, and then the total number of tracks and the total playing time on the MiniDisc will be displayed.

5 Press the MD button to start playback.

� If the MiniDisc has a track name, it will appear and scroll across the display. Then, the elapsed playing time will appear.

� If the MiniDisc has no track names, the elapsed playing time will appear.

� When the last track has finished playing, the MD player will stop automatically.


22

CX1H_UK17-25.fm00/12/17

MD

Pla

ybac

kLi

sten

ing

to a

Min

iDis

c

Listening to a MiniDisc (continued)

To interrupt playback:Press the MD button.To resume playback from the same point, press the MD button again.

To stop playback:Press the MD button.

To remove a MiniDisc:Whilst in the stop mode, press the MD button.

Caution:� When loading a MD, make sure to turn the power on. If the MD is inserted forcibly

without turning the power on, it may cause malfunctions.� When transporting the unit, take out the MD. It may be jammed inside and cause

malfunctions.� If TV or radio interference occurs during MiniDisc operation, move the unit away

from the TV or radio.� Although MiniDiscs will not normally skip due to vibration, you may hear skipping

in the sound if there is continuous vibration. If the volume is turned up too high,sound skipping may occur depending on the contents of the MiniDisc. If this hap-pens, turn the volume down and the skipping should stop.

� If an error message is displayed during MiniDisc operation, see "Error Messages"on page 57.

� To locate the beginning of a track

� To locate the desired portion

Notes:� Normal playback will resume when the or button is released.� When the end of the last track is reached during fast forward, "END" will appear in

the display and MiniDisc operation will be paused. When the beginning of the firsttrack is reached during fast reverse, the unit will enter the playback mode.

� To select a track more than 10 tracks ahead

Whilst in the stop mode or playback:1 Press the +10 button to forward by 10 tracks.2 Press the or button to move forward or backward by 1 track. For example, to move to the 27th track when listening to the 5th track:

To move to the beginning of the next track:



To restart the track being played:



For audible fast forward:


For audible fast reverse:


(5th track)

(15th) (25th) (26th) (27th)


23

CX1H_UK17-25.fm00/12/17

MD

Pla

ybac

kLi

sten

ing

to a

Min

iDis

c

� Switching the time display Each time the TIME button on the remote control is pressed during playback, the dis-play will change.

Notes:� During random play, the total remaining playing time will not be displayed.� Depending on the MiniDisc, the playing time display may not match the total play-

ing time which is indicated on the MiniDisc jacket, as the time between tracks isnot included.

� Switching the track name or level meter etc.

Each time the DISPLAY button on the remote control is pressed during playback, thedisplay will change.

Notes:� When the level meter is displayed, it remains unchanged during playback.� It returns to normal when the MD is removed.� The remaining recording time, and the date and the time of recording are not displayed

for playback-only MD.


The remaining playing time for the current track will be displayed.

The total remaining playing time for the disc will be displayed.


The track name will be displayed.

"NO NAME" is displayed if the track is not named.

The level meter is displayed.

Tracks recorded in monaural is indicated as "M".

Remaining recording time is displayed.

Date of recording is displayed.

Time of recording is displayed.


24

CX1H_UK17-25.fm00/12/17

Adv

ance

d C

D/M

D P

layb

ack

Dire

ct p

lay

/ Rep

eat o

r Ran

dom

pla

y

Direct Play

When in the CD or MD mode, press the direct buttons to select the desired tracks.

To select a track between the 11th and 99th tracks:Select the track after pressing the 10 button.A. For example, to choose 28

To select a track beyond the 100th track (MD only):Select the track after pressing the 10 button twice.B. For example, to choose 105

Repeat or Random playYou can select the CD or MD playback mode; "Repeat play", "Random play" and"Normal play".

To repeat a programmed sequence:Perform steps 1 - 5 in the "Programmed Play" section and then select the repeat play-back.

Notes:� You can select the playback mode by pressing the PLAY MODE button on the

main unit.� During programme operation, random play is not possible.� After using repeat play, be sure to press the button. Otherwise, the disc(s) will

play continuously.� The random play will stop automatically when all tracks are played once. (The

same track will not be played back twice.) � In random play, the CD or MiniDisc player will select and play tracks automatically.

(You cannot select the order of the tracks.)

To cancel repeat or random play:Press the PLAY MODE button repeatedly to select the normal play mode.

1 Press the " 10" button.

2 Press the "2" button.


1 Press the " 10" button twice.


3 Press the "0/10" button.


1 When in the CD or MD mode, press the PLAY MODE button repeat-edly to select the playback mode.

2 Press the CD or MD button to start playback.


25

CX1H_UK17-25.fm00/12/17

Adv

ance

d C

D/M

D P

layb

ack

Pro

gram

med

pla

y

Programmed PlayUp to 20 CD tracks or 20 MD tracks can be programmed.You cannot programme CD and MiniDisc tracks together at the same time.

To clear the programmed selections:Press the CLEAR button whilst the "PROGRAM" indicator is flashing.� Each time the button is pressed, one track will be cleared, beginning with the last

track programmed.

To cancel the programmed play mode:Whilst in the stop mode, press the CLEAR button. The "PROGRAM" indicator will dis-appear and all the programmed content will be cleared.

Adding tracks to the programme:If a programme has been previously stored, the "PROGRAM" indicator will be dis-played. Then follow steps 1 - 5 to add tracks. The new tracks will be stored after thelast track of the original programme.

To check which tracks are programmed:Whilst the unit is stopped in the programmed play mode, press the or button.

Notes:� Ejecting a CD or MiniDisc automatically cancels the programmed sequence.� Even if you press the ON/STAND-BY button to enter the stand-by mode or change

the function from CD or MD to another function, the programmed selections willnot be cleared.

� During programme operation, random play is not possible.

1 Whilst in the stop mode, press the CD or MD button.

2 Press the PROGRAM button to enter the programming save mode.

3 Press the direct buttons to select the desired track.

4 Repeat step 3 for any other track. Up to 20 tracks can be pro-grammed.

If the total programmed playback time exceeds 400 minutes, "--:--" is displayed. However, it is properly memorised.

5 Press the CD or MD button.

6 Press the CD or MD button to start playback.

Playback order

Playback time


26

CX1H_UK26-34.fm00/12/17

Rad

ioLi

sten

ing

to th

e R

adio

Listening to the Radio� Tuning

After use:Press the ON/STAND-BY button to enter the stand-by mode.


2 Press the TUNER (BAND) button repeatedly to select the desiredfrequency band (FM STEREO, FM or AM).

3 Press the TUNING or button to tune in to the desired station.

Manual tuning:

Press the TUNING or button as many times as required to tune in to the desired station.

Auto tuning:

When the TUNING or button is pressed for more than 0.5 seconds, scan-ning will start automatically and the tuner will stop at the first receivable broad-cast station.

You can tune in to the desired station by pressing the or button on the remote control.

Notes:

� When radio interference occurs, auto scan tuning may stop automatically at that point.

� Auto scan tuning will skip weak signal stations.

� When an RDS (Radio Data System) station is tuned in, the frequency will be dis-played first, and then the RDS indicator will light. Finally, the station name will ap-pear.

� Full auto tuning can be achieved for RDS stations "ASPM", see page 30.

4 To receive an FM stereo transmission, press the TUNER (BAND)button. The "STEREO" indicator lights up.

� "ST" will appear when an FM broadcast is in stereo.

� If the FM reception is weak, press the TUNER (BAND) button. The "STEREO" in-dicator goes out. The reception changes to monaural, and the sound becomes clearer.


27

CX1H_UK26-34.fm00/12/17

Rad

ioLi

sten

ing

to th

e R

adio

� Preset tuning(Remote control operation)You can store 40 AM and FM stations in memory and recall them at the push of a but-ton.

Note:The backup function protects the memorised stations for a few hours should there bea power failure or the AC power lead disconnection.

� To recall a memorised station(Remote control operation)Press the TUN. PRESET or button to select the desired station.

The direct buttons allow you to recall a memorised station.

To select a preset station between the 11 and 40:For example, to choose 28

� To erase all the contents of the preset memory

(Remote control operation)

1 Perform steps 1 - 4 in the "Tuning" section on page 26.

2 Press the ENTER button to enter the preset tuning saving mode.

3 Within 5 seconds, press the TUN. PRESET or button to selectthe preset channel number.

� Store the stations in memory, in order, starting with preset channel 1.

4 Within 5 seconds, press the ENTER button to store that station inmemory.

� If the preset number indicator goes out before the station is memorised, repeat the operation from step 2.

5 Repeat steps 1 - 4 to set other stations, or to change a preset sta-tion.

� When a new station is stored in memory, the station previously memorised will be erased.

1 Press the " 10" button.



1 Press the TUNER (BAND) button.

2 Hold the CLEAR button down for 3 seconds or more.



28

CX1H_UK26-34.fm00/12/17

RD

S R

adio

Usi

ng th

e R

adio

Dat

a S

yste

m (

RD

S)

Using the Radio Data System (RDS)RDS is a broadcasting service which a growing number of FM stations provide.These FM stations send additional signals along with their regular programmesignals. They send their station names, and information about the type of pro-gramme such as sports or music, etc.When tuned to an RDS station, "RDS" and the station name will be displayed."TP" (Traffic Programme) will appear on the display when the received broadcast car-ries traffic information, and "TA" (Traffic Announcement) will appear whilst a trafficinformation is on air (see page 34)."EON" will appear whilst the EON (Enhanced Other Networks information) data isbroadcast."PTYI" (Dynamic PTY Indicator) will appear whilst the Dynamic PTY station isreceived. You can control the RDS by using the remote control only.

� Information provided by RDS

When you are tuning in to a station other than an RDS station or to an RDS stationwhich sends weak signal, the display will change in the following order:

Each time the DISPLAY button is pressed, the display will switch as follows:

Frequency Level meter

Station name (PS)

Frequency

Level meter

Programme type(PTY)(English fixed)


29

CX1H_UK26-34.fm00/12/17

RD

S R

adio

Usi

ng th

e R

adio

Dat

a S

yste

m (

RD

S)

Descriptions of the PTY (Programme Type) codes, TP (Traffic Programme) and TA(Traffic Announcement).You can search for and receive the following PTY, TP and TA signals.

Note:When you select a programme in the EON stand-by mode, the unit will display "TI" insteadof "TA".

News Short accounts of facts, events and publicly expressed views, reportage and actuality.

Affairs Topical programme expanding or enlarging upon the news, generally in different presentation style or concept, including debate, or analysis.

Info Programmes whose purpose is to impart advice in the widest sense.

Sport Programme concerned with any aspect of sport.

Educate Programme intended primarily to educate, of which the formal element is fundamental.

Drama All radio plays and serials.

Culture Programmes concerned with any aspect of national or regional culture, in-cluding language, theatre, etc.

Science Programmes about the natural sciences and technology.

Varied Used for mainly speech-based programmes usually of light-entertainment nature, not covered by other categories. Examples include: quizzes, panel games, personality interviews.

Pop M Commercial music, which would generally be considered to be of current popular appeal, often featuring in current or recent record sales charts.

Rock M Contemporary modern music, usually written and performed by young mu-sicians.

Easy M Current contemporary music considered to be "easy-listening", as op-posed to Pop, Rock or Classical, or one of the specialised music styles, Jazz, Folk or Country. Music in this category is often but not always, vocal, and usually of short duration.

Light M Classical music for general, rather than specialist appreciation. Examples of music in this category are instrumental music, and vocal or choral works.

Classics Performances of major orchestral works, symphonies, chamber music, etc., and including Grand Opera.

Other M Musical styles not fitting into any of the other categories. Particularly used for specialist music of which Rhythm & Blues and Reggae are examples.

Weather Weather reports and forecasts and meteorological information.

Finance Stock Market reports, commerce, trading, etc.

Children For programmes targeted at a young audience, primarily for entertainment and interest, rather than where the objective is to educate.

Social Programmes about people and things that influence them individually or in groups. Includes: sociology, history, geography, psychology and society.

Religion Any aspect of beliefs and faiths, involving a God or Gods, the nature of ex-istence and ethics.

Phone in Involving members of the public expressing their views either by phone or at a public forum.

Travel Features and programmes concerned with travel to near and far destina-tions, package tours and travel ideas and opportunities. Not for use for an-nouncements about problems, delays, or roadworks affecting immediate travel where TP/TA should be used.

Leisure Programmes concerned with recreational activities in which the listener might participate. Examples include, Gardening, Fishing, Antique collect-ing, Cooking, Food & Wine, etc.

Jazz Polyphonic, syncopated music characterised by improvisation.

Country Songs which originate from, or continue the musical tradition of the Amer-ican Southern States. Characterised by a straightforward melody and nar-rative story line.

Nation M Current Popular Music of the Nation or Region in that country's language, as opposed to International 'Pop' which is usually US or UK inspired and in English.

Oldies Music from the so-called "golden age" of popular music.

Folk M Music which has its roots in the musical culture of a particular nation, usu-ally played on acoustic instruments. The narrative or story may be based on historical events or people.

Document Programme concerned with factual matters, presented in an investigative style.

TEST Broadcast when testing emergency broadcast equipment or receivers.

Alarm ! Emergency announcement made under exceptional circumstances to give warning of events causing danger of a general nature.

None No programme type (receive only).

TP Broadcasts which carry traffic announcements.

TA Traffic announcements are being broadcast.


30

CX1H_UK26-34.fm00/12/17

RD

S R

adio

Usi

ng th

e R

adio

Dat

a S

yste

m (

RD

S)

Using the Radio Data System (RDS) (continued)

� Using the Auto Station Programme Mem-ory (ASPM)

Whilst in the ASPM operation mode, the tuner will automatically search for new RDSstations. Up to 40 stations can be stored.If you have already stored some stations in memory, the number of new stations youcan store will be less.

To stop the ASPM operation before it is complete:Press the ASPM button whilst it is scanning for stations.The stations which are already stored in memory will be kept there.

Notes:� If the same station is broadcasting on different frequencies, the strongest fre-

quency will be stored in memory.� Any station which has the same frequency as the one stored in memory will not be

stored.� If 40 stations have already been stored in memory, the scan will be aborted. If you

want to redo the ASPM operation, erase the preset memory.� If the RDS signals are very weak, station names may not be stored in memory.

To erase all of the contents of preset memory:

To store a station name again if the wrong name was stored in mem-ory:It may be impossible to store station names in memory using the ASPM function ifthere is lots of noise or if the signal is too weak. In this case, perform as follows.

Notes:� The same station name can be stored in different channels.� In a certain area or during certain time periods, the station names may temporarily

be different.

1 Press the TUNER (BAND) button to select the FM band.

2 Press and hold down the ASPM button for at least 3 seconds.

After "ASPM" has flashed for about 4 seconds, scanning will start (87.50 - 108.00 MHz).

When an RDS station is found, "RDS" will appear for a short time and the station will be stored in memory.

After scanning, the number of stations stored in memory will be displayed for 4 sec-onds, and then "END" will appear for 4 seconds.

1 Press the TUNER (BAND) button.2 Hold the CLEAR button down for 3 seconds

or more.3 Press the ENTER button.

1 Press the TUN. PRESET or button to check whether the names are correct.2 If you find a wrong name during receiving the station. Wait until the correct name

will be displayed. And then press the ENTER button.3 Within 5 seconds, press the TUN. PRESET or button to display the preset

channel to be corrected again. 4 Within 5 seconds, press the ENTER button.� The new station name has been stored in memory correctly.


31

CX1H_UK26-34.fm00/12/17

RD

S R

adio

Usi

ng th

e R

adio

Dat

a S

yste

m (

RD

S)

� To recall stations in memoryTo specify programme types and select stations (PTY search):You can search a station by specifying the programme type (news, sports, traffic pro-gramme, etc. ... see page 29) from the stations in memory.

Notes:� If the display has stopped flashing, start again from step 2. If the unit finds out a

desired programme type, corresponding the station name will flash for 10 secondsand remain lit.

� If you want to listen to the same programmed type of another station, press thePTY-TI button whilst the channel number and station name are flashing. The unitwill look for the next station.

� If no station can be found, "NOT FOUND" will appear for 4 seconds.

If you select the traffic programme:If you select the traffic programme (TP) in step 4, "TP" will appear. (This does notmean that you can listen to the traffic information at that time.)When a traffic information is broadcast, "TA" will appear.

To specify station names and select stations manually:You can select a station by specifying the name (BBC R1, BBC R2, etc.) from the sta-tions stored in memory.Before starting this operation, you must store one or more station names in memory.

1 Press the TUNER (BAND) button to select the FM band.

2 Press the PTY-TI button.

� "PTY TI" and "SELECT" will appear alternately for about 6 seconds.

3 Within 6 seconds, press the TUN. PRESET or button to selectthe programme type you want.

� Each time the button is pressed, the programme type will appear. If the button is held down for more than 0.5 seconds, the programme type will appear continu-ously.

4 Whilst the selected programme type is flashing (within 4 seconds),press the ENTER button.

� After the selected programme type has been lit for 2 seconds, "SEARCH" will ap-pear, and the search operation will start.

1 Press the TUNER (BAND) button to select the FM band.2 Press the TUN. PRESET or button to select the desired station.

3 The station name will be displayed for 3 seconds. Then the display will change as follows.


32

CX1H_UK26-34.fm00/12/17

RD

S R

adio

Usi

ng th

e R

adio

Dat

a S

yste

m (

RD

S)


� To automatically play the desired pro-gramme (EON-PTY)

When the desired type of programme is broadcast, the radio switches to it automati-cally.

Checking the stand-by mode setting:When in the EON stand-by mode, press the EON button. ("Programme type" "WAITING")

To cancel the EON stand-by mode:When in the EON stand-by mode, press the EON button. Within 4 seconds, press itagain. ("PTY" will go out.)

About the PTYI (Dynamic PTY Indicator):"PTYI" (Dynamic PTY Indicator) will appear whilst the Dynamic PTY station isreceived. Dynamic PTY indicates that the PTY for the station tuned in, or the PTY ref-erenced in the EON data, is assessed whenever the programme changes and maybe changed.

� When "PTYI" appears, press the DISPLAY button to check the type of the currentprogramme.

1 Tune in to an RDS station (when a station name is displayed).

2 Press the EON button when "EON" appears.


� If the EON button is pressed when "EON" is not displayed, "NO EON" will appear for 5 seconds to indicate that the unit cannot enter the EON stand-by mode.

3 Whilst they are displayed, select the desired programme type bypressing the TUN. PRESET or button.

� The selected programme type will flash.


� The selected programme type and "WAITING" will be displayed for 2 seconds each.

� "PTY" will appear, and the unit will enter the EON-PTY stand-by mode.

5 When the specified programme starts on an ON (other network) sta-tion, the unit will automatically switch to the station and "PTY" willflash.

6 When the programme is over, the unit will automatically return to theoriginal station.

PTYI Meaning

Lights up Tuned in to a dynamic PTY station.

Goes out Tuned in to a static PTY.


33

CX1H_UK26-34.fm00/12/17

RD

S R

adio

Usi

ng th

e R

adio

Dat

a S

yste

m (

RD

S)

� To automatically play the traffic informa-

tion (EON-TI)When the traffic information is broadcast, the radio switches to it automatically.

Checking the stand-by mode setting:When in the EON stand-by mode, press the EON button. ("TI" "WAITING")

To cancel the EON stand-by mode:When in the EON stand-by mode, press the EON button. Within 4 seconds, press itagain. ("TI" will go out.)

1 Tune in to an RDS station (when a station name is displayed).

2 Press the EON button when "EON" appears.


� If the EON button is pressed when "EON" is not displayed, "NO EON" will appear for 5 seconds to indicate that the unit cannot enter the EON stand-by mode.

3 Whilst they are displayed, select the TI (Traffic Information) bypressing the TUN. PRESET or button.


� "TI" and "WAITING" will appear for 2 seconds each.

� "TI" will appear, and the unit will enter the EON-TI stand-by mode.

5 When a TA specified starts on an ON (other network) station, theunit will automatically switch to that station, and "TI" will flash.

6 When the traffic announcement is over, the unit will automaticallyreturn to the original station you were tuned to.


34

CX1H_UK26-34.fm00/12/17

RD

S R

adio

Usi

ng th

e R

adio

Dat

a S

yste

m (

RD

S)


� Notes for RDS operationIf any of the following events occur, it does not mean that the unit is faulty:� "PS", "NO PS" and a station name appear alternately, and the unit does not oper-

ate properly.� If a particular station is not broadcasting properly or a station is conducting tests,

the RDS reception function may not work properly.� When you receive an RDS station whose signal it too weak, information like the

station name may not be displayed.� "NO PS" or "NO PTY" will flash for about 5 seconds, and then the frequency will be

displayed.

About the "TP" and "TA" indicators:

In the following cases, the EON stand-by mode will be cancelled.� When you press the ON/STAND-BY button to enter the stand-by mode.� When the unit is switched to another band in the EON stand-by mode.� When you change the FM station whilst in the EON stand-by mode.� When a preset call is made.

Notes:� Whilst the same programme as the specified PTY (or TA) is being broadcast, the

unit will not switch to an ON (other network) station.� If there are more than two other network stations, compare the strength of signal

and tune in to the station with the strongest signal (EON-AF). If other network sta-tion has been stored in the preset channel memory, the unit will switch to thatchannel.

� If you want to leave an ON (other network) station tuned in by the EON and returnto the station you were receiving, press the EON button.

� After the unit returns to the original station, the stand-by mode will still be active.(The "TI" or "PTY" will remain lit.)

� The unit does not switch between ON stations. It returns to the original station.� If there is any problem with the ON station the unit switched to, "WEAK SIG" will

appear and the unit will return to the original station.� If the signal from the ON station the unit switched to is very weak, the unit will

search for another station with the strongest signal. However, if the signals from allstations are weak or not good (due to electrical noise), the unit displays "WEAKSIG" and returns to the original station.

"TP" "TA" Meaning

Not lit Not lit Does not carry traffic announcements nor does it refer, via EON, to a programme that does.

Not lit Lit Carries EON information about another programme which gives traffic information.

Lit Not lit Carries traffic announcements but not at present and may also carry EON information about other traffic announce-ments.

Lit Lit A traffic information is currently on air.


35

CX1H_UK35-41.fm00/12/17

MD

Rec

ordi

ngB

efor

e R

ecor

ding

to a

Min

iDis

c

Before Recording to a MiniDisc� Disc writing (TOC)

When you start recording or editing, "TOC" will appear on the display.This indicates that information in the TOC is now being changed according to therecording or editing being performed. (The changed TOC is not yet recorded on theMiniDisc at this time.)

The TOC is recorded when� You stop recording.� You switch to another input source.� You eject the MiniDisc.� You set the unit to the stand-by mode.

Do NOT unplug the power lead whilst the TOC is being recorded ("TOC" is flashing)and do NOT impart shock to the unit. Otherwise, TOC will not be correctly recorded,and consequently proper playback may not be possible.

Recordings cannot be made in the following situations.� If you try recording on a playback-only MiniDisc (commercially available music

MiniDisc).� If a MiniDisc is protected against accidental erasure. (See page 56.)� If there is no more recording time left on the disc. (See page 57.)� When the "TOC FULL" message appears. (See page 57.)� If a disc's TOC has been damaged.

� Notes for recording� SHARP is not liable for damage or loss of your recording arising from malfunction

of this unit.� When recording important selections, be sure to make a preliminary test to ensure

that the desired material is being properly recorded.� The VOLUME, SURROUND, X-BASS and PASS/EQ controls can be adjusted with

no effect to the recorded signal (Variable Sound Monitor).

� About ATRACThe ATRAC (Adaptive TRansform Acoustic Coding) system compresses the sounddata into 1/5 by cutting out the inaudible sound. Since the sound is selected based onpsychoacoustics masking, the sound quality is not impaired.This unit is equipped with the ATRAC3 compressing system that can reduce thesound data to 1/10 or 1/20 of it's original size.By employing this system, 2 times and 4 times long recording is enabled in stereomode.

The TOC (Table of Contents) is information on track numbers and recording areas to allow the unit to recognise musical selections or sounds. The entire MiniDisc is controlled depending on this TOC, which enables the unit to find the be-ginning of a track quickly or to automatically record in a vacant area.

Area for TOC (recording track numbers, track

names, etc.)

Area for record-ing the sound


36

CX1H_UK35-41.fm00/12/17

MD

Rec

ordi

ngR

ecor

ding

to a

Min

iDis

c fro

m a

CD

Recording to a MiniDisc from a CD


2 Press the CD button and load the desired CD.

3 Load a recordable MiniDisc into the MD compartment.

4 Press the REC MODE button to select the recording mode.

Stereo recording Monaural recording

2 times long record-ing (stereo)

4 times long record-ing (stereo)

Indication Recording mode Recording

(to record on 80-minute MD)

SP Stereo recording Maximum 80 minutes

LP2 2 times long recording (stereo) Maximum 160 minutes

LP4 4 times long recording (stereo) Maximum 320 minutes

MONO Monaural recording Maximum 160 minutes

� The recording mode cannot be changed whilst recording.

� The recording mode remains unchanged until it is changed.

5 Press the CD MD EDIT (HIGH/NORMAL) button to start record-ing.HIGH : High speed recording.

NORMAL : Normal speed recording.

� Recording is performed digitally.


37

CX1H_UK35-41.fm00/12/17

MD

Rec

ordi

ngR

ecor

ding

to a

Min

iDis

c fro

m a

CD

Note:� Recording from a CD to a MiniDisc starts even if all the tracks on the CD cannot fit

in the MiniDisc. In that case, both the CD and MD stop when the MD becomes full.� When the CD reaches its end, recording to MD will stop simultaneously.� You can record from a CD you programmed.� Recording can be performed in repeat playback mode. The repeat playback can

be switched during recording. To stop recording:Press the CD or MD button.The CD and MiniDisc will stop.

After use:Press the ON/STAND-BY button to enter the power stand-by mode.

Notes for long recording mode:� Tracks recorded in 2 times long recording or 4 times long recording mode cannot

be played with units that do not support these modes.� On such a unit, "LP :" is displayed at the beginning of the track and no sound is

heard. (The operation and the display may vary depending on the unit.)

Note for high speed recording:Due to the scratch, dirt, or the recorded condition, the sound may be cut in pieces orthe noise is heard from the MD recorded in high speed. If this occurs, record the MDat the normal speed.

Caution for 4 times long recording (LP4):Special compressing method allows the 4 times long recording to realize long-timestereo recording. Therefore, some noise is recorded occasionally.If sound quality is the main requirement, stereo recording or 2 times long recording isrecommended.

About track numbers:

New track numbers will be created auto-matically according to the original tracks (Synchro mark function).

� When you record from a CD to a Mi-niDisc, the track numbers recorded on the MiniDisc may not match the track numbers on the CD.

Track A

First track Third trackSecond track

First track

MiniDisc

CDThird trackSecond track

Track B Track C

Track A Track B Track C


38

CX1H_UK35-41.fm00/12/17

MD

Rec

ordi

ngR

ecor

ding

to a

Min

iDis

c fro

m a

CD

Recording to a MiniDisc from a CD (continued)

� Recording the desired tracks of the CD

When the recording is finished, the selected tracks will be cleared. To memorise a track whilst listening to it:

To clear the memorised tracks:Press the CD button whilst in the stop mode.


2 Press the CD button and load the desired CD.


4 Press the or button to select the desired track.

5 Press the TRACK button to programme the track number.

Selected track number T-EDIT

6 Repeat steps 4 - 5 for other tracks. Up to 20 tracks can be pro-grammed.

� If more than 20 tracks are selected, "EDIT OVER" is displayed and the 21st track will not be memorised.

7 Press the CD MD EDIT (HIGH/NORMAL) button to start record-ing.

1 When you hear a track you want to record during playback, press the TRACK button.

� The track is memorised. (Maximum 20 tracks can be memorised.)

2 After the track is memorised, press the CD button to stop playback.

3 Press the HIGH or NORMAL button to start recording.


39

CX1H_UK35-41.fm00/12/17

MD

Rec

ordi

ngR

ecor

ding

to a

Min

iDis

c fro

m a

CD

� Recording on the top position of a recorded MiniDisc

When the recording is finished, the top position mode will be cancelled.The recorded track will be the first track on the MiniDisc.All the tracks previously recorded will be renumbered.Note:� Whilst in the pause mode or recording, the top position mode cannot be set or

cancelled.

� Adjusting the recording levelYou can adjust the recording level depending on the recording source by watching thelevel meter.

To stop recording:Press the MD button.The MiniDisc will stop.The CD will continue playback.

1 Prepare for recording.

To record from a CD: To record from the radio:

Load the desired CD and a recordable MiniDisc.

Tune in to the desired station and load a recordable MiniDisc.

2 Press the TOP POSITION button.

One more press will cancel the top position mode.

3 Start recording.

To record from a CD: To record from the radio:

Press the HIGH or NORMAL button. Press the MD button after pressing the REC button.


2 Press the or button to select the desired track.


4 Press the CD button to start playback.

5 Press the REC button to pause recording.

6 Press the REC LEVEL/CURSOR or button to adjust the record-ing level.

Level meter Recording level

� Maximum level should not exceed "0dB".

� The recording level can be adjusted in 2dB intervals between -4dB and +10dB.


8 Press the or button again to select the desired track to berecorded.

9 Press the CD button again to start recording.

0dB -4dB ··· +10dB


40

CX1H_UK35-41.fm00/12/17

MD

Rec

ordi

ngR

ecor

ding

to a

Min

iDis

c fro

m th

e R

adio

Recording to a MiniDisc from the Radio

To interrupt recording:Press the MD button.To resume recording from the same point of MiniDisc, press the MD button again. To stop recording:Press the MD button.The MiniDisc will stop.

To mark track numbers whilst recording from the radio:Press the REC button at the desired position during recording to create a new tracknumber. The track counter will be increased by one every time the button is pressed.

1 Tune in to the desired station. (See page 26.)



4 Press the REC button.

� The unit will enter the recording stand-by mode.

5 Press the MD button to start recording.

About track numbers:

A recording is performed as a single track, and only one number is created.

Track A

Single track

First track

MiniDisc

RadioThird trackSecond track

Track B Track C

(Track A) (Track B) (Track C)


41

CX1H_UK35-41.fm00/12/17

MD

Rec

ordi

ngC

heck

ing

Dis

play

s

Checking Displays� To check the recording mode and remain-

ing recording time� To check the display whilst in the record-

ing mode

Whilst in the stop mode in MD function, press the REC MODE button.

Each time the button is pressed, the display will change as follows.

� After the remaining recording time is displayed, the display will return to normal.

� When resuming recording, it will be started in the recording mode that is con-firmed in this procedure.

Remaining time in stereo recording mode

Remaining time in 2 times long recording mode

Remaining time in 4 times long recording mode

Remaining time in monaural recording mode

Whilst in the recording mode, press the DISPLAY button.

Each time the button is pressed, the display will change as follows.

� When recording is finished, the display will return to normal.

� Even if the recording mode is monaural, the level meter is displayed in stereo.

Elapsed playing time

"NO NAME" appears.

Level meter

Remaining recording time


42

CX1H_UK42-48.fm00/12/17

MD

Edi

ting

Titl

ing

a M

iniD

isc

Titling a MiniDisc� Creating disc and track namesYou can give a name to discs and tracks.One disc name and up to 255 track names can be created per disc (a maximum of 40characters for the disc and each track name and a total of 1,700 characters can beentered).� Playback-only MiniDisc cannot be edited.

1 Press the MD button and load a MiniDisc. (See page 21.)

2 Select either "DISC NAME" or "TRACK NAME".

To create a disc name: To create a track name:

Whilst in the stop mode of MiniDisc, press the NAME/TOC EDIT button, and within 10 seconds, press the REC LEVEL/CURSOR or button to se-lect "DISC NAME".

During playback or in the pause mode of MiniDisc, press the NAME/TOC EDIT button to select "TRACK NAME".


� To cancel the operation, press the NAME/TOC EDIT button.

� The unit will enter the character input mode.


43

CX1H_UK42-48.fm00/12/17

MD

Edi

ting

Titl

ing

a M

iniD

isc

Characters (symbols):

To erase disc and track names:

To delete a character:

To add a character:

4 Press the 1 - 10, SYMBOL and CHARACTER buttons to enter thecharacters.

� The CHARACTER button allows switching between capital and small letters.

� You can enter the following symbols by pressing the SYMBOL button.

5 When the name has been completely entered, press the ENTERbutton.

Capitalletters 1 ABC 2 DEF 3 GHI 4 JKL 5 MNO 6 PQRS 7 TUV 8 WXYZ 9 0

01 abc 2 def 3 ghi 4 jkl 5 mno 6 pqrs 7 tuv 8 wxyz 9Smallletters

– . , / : ? & ( ) ! " # $ % ∗ ; < = > @ _ ` + '

: indicates a space.

1 Perform steps 1- 2 in the "Creating disc and track names" section on page 42.

2 Press the TIMER/DELETE button for 3 seconds or more.

� "NAME CLEAR?" will appear.

3 Press the ENTER button to finish.


2 Press the REC LEVEL/CURSOR or button on the remote control to flash the character to be deleted.


4 Press the ENTER button to finish.


2 Press the REC LEVEL/CURSOR or button on the remote control to flash the character before which you want to add a new character.

3 Select a character to enter, press the ENTER button.


44

CX1H_UK42-48.fm00/12/17

MD

Edi

ting

Titl

ing

a M

iniD

isc

/ Edi

ting

a R

ecor

ded

Min

iDis

c

Titling a MiniDisc (continued)

To change a character:Example) To change "LAVE" to "LOVE"

Editing a Recorded MiniDisc� To divide a track

Notes:� If you divide a track that has a name and the date of recording, the two new tracks

will have the same name and the date of recording.� However, if there is not enough space to memorise the characters in "TOC", the

second track will not be named.� Each disc can hold up to 255 tracks. However, even if the number of assigned

tracks has not reached 254, it might not be possible to make any further divisionsof tracks.

1 Perform steps 1- 3 in the "Creating disc and track names" section on page 42.2 Press the REC LEVEL/CURSOR or button on the remote control to flash the char-

acter to be changed.


4 Enter a new character.


1 Play the track which you want to divide into two, and press the MD button at the point where you want to divide the track.

2 Press the NAME/TOC EDIT button, and within 10 seconds, select"DIVIDE" by pressing the REC LEVEL/CURSOR or button.



4 Press the ENTER button again.

� The track is divided, and the unit is stopped at the beginning of the second of the two tracks.

� The numbers of the tracks which come after the divided track are automatically increased by one.


45

CX1H_UK42-48.fm00/12/17

MD

Edi

ting

Edi

ting

a R

ecor

ded

Min

iDis

c

� To combine tracks Notes:

� First, put the two tracks next to each other in the order you want using the MOVEfunction. Then combine them using the COMBINE function.

� This function cannot be used in the random play mode and programmed playmode.

� If both tracks to be combined have a name, or only the first track has a name, thefirst track name will be used.

� When the first track does not have a name, the combined track will be named asfollows.

In the following cases, tracks may not be combined.� Digital recorded track and analogue recorded track.� Tracks recorded in different recording modes (monaural, stereo, 2 times long

recording, 4 times long recording) cannot be combined.� Short tracks may not be combined (8 seconds for stereo, 16 seconds for monaural

and 2 times long recording, 32 seconds for 4 times long recording).

1 Whilst in the stop mode, select the second of the two adjacenttracks you want to combine by pressing the or button. Orstart playing the second of the two tracks you want to combine,and then press the MD button.

2 Press the NAME/TOC EDIT button, and within 10 seconds, select"COMBINE" by pressing the REC LEVEL/CURSOR or button.




� The two tracks are combined, and the unit is stopped at the beginning of the com-bined track.

� The numbers assigned to the tracks following the combined track are automati-cally decreased by one.

The second track name will be used for tracks recorded in monaural or stereo. No name will be given to tracks recorded in 2 times or 4 times long recording mode.


46

CX1H_UK42-48.fm00/12/17

MD

Edi

ting

Edi

ting

a R

ecor

ded

Min

iDis

c

Editing a Recorded MiniDisc (continued)

� To move a track

1 Whilst in the stop mode, select the track you want to move bypressing the or button. Or start playing the track to bemoved, and then press the MD button.

2 Press the NAME/TOC EDIT button, and within 10 seconds, select"MOVE" by pressing the REC LEVEL/CURSOR or button.


4 Select the new track position by pressing the or button.



� The track is moved, and the unit is stopped at the beginning of the track selected in step 4.


47

CX1H_UK42-48.fm00/12/17

MD

Edi

ting

Edi

ting

a R

ecor

ded

Min

iDis

c

� To move the programmed tracks

Note:� If a track is programmed twice or more, the first instruction will precede to the oth-

ers.

� To erase one track

Caution:Once a track has been erased, it cannot be recovered. Check the track numberbefore erasing it.

Notes:� When a track is erased, the numbers assigned to the tracks following the erased

track will be automatically decreased by one.� When a track is erased, the track name will be erased at the same time.� It is also possible to erase tracks by selecting either menu of "ERASE" or "ALL

ERASE" with the NAME/TOC EDIT button on the remote control.

1 Programme the tracks you want to move. (See page 25.)

2 Press the NAME/TOC EDIT button.




� Tracks are rearranged.

� The programmed tracks will come to the top of the disc.

1 Whilst in the stop mode, select the track you want to erase bypressing the or button. Or start playing the track to beerased, and then press the MD button to enter the pause mode.

2 Press the ERASE button.

� To cancel the operation, press the MD button.

3 Press the ERASE button for 2 seconds or more.

� The track is erased, and the unit is stopped at the beginning of the next track.


48

CX1H_UK42-48.fm00/12/17

MD

Edi

ting

Edi

ting

a R

ecor

ded

Min

iDis

c

Editing a Recorded MiniDisc (continued)

� To erase all the tracks at once � To erase the programmed tracks at once


2 Press the ERASE button.


3 Press the ERASE button for 3 seconds or more.

� All the track numbers and track names are erased.

1 Programme the tracks you want to erase. (See page 25.)

� Up to 20 tracks can be programmed.

2 Press the NAME/TOC EDIT button on the remote control.

3 Within 10 seconds, press the REC LEVEL/CURSOR or buttonon the remote control to select the "PRGM ERASE".

4 Within 10 seconds, press the ENTER button on the remote control.


5 Press the ENTER button on the remote control.

� The programmed tracks are erased.


49

CX1H_UK49-59.fm00/12/17

Adv

ance

d F

eatu

res

Tim

er a

nd S

leep

Ope

ratio

n

Timer and Sleep OperationTimer playback:The unit turns on and plays the desired source (CD, MD, TUNER, AUX) at the presettime. At the end time, the unit enters the power stand-by mode automatically. Timer recording:The unit turns on and starts recording from the desired source (TUNER, AUX) at thepreset time. At the end time, the unit enters the power stand-by mode automatically.

� Timer playback/Timer recordingBefore setting timer:

Whilst the power is in the stand-by mode, press the DISPLAY button on the re-mote control to check that the clock is on time.



3 Within 10 seconds, press the REC LEVEL/CURSOR or buttonto select "TIMER SET".


Continued to the next page


50

CX1H_UK49-59.fm00/12/17

Adv

ance

d F

eatu

res

Tim

er a

nd S

leep

Ope

ratio

n

Timer and Sleep Operation (continued)

5 Press the REC LEVEL/CURSOR or button to select "TIMERPLAY" or "TIMER REC" mode.For timer playback: For timer recording:


7 Press the REC LEVEL/CURSOR or button to specify the hourto start, and press the ENTER button.

8 Press the REC LEVEL/CURSOR or button to specify the min-utes, and press the ENTER button.

� Unless the timer setting is changed, the ending time will automatically be set for one hour after the starting time.

9 Press the REC LEVEL/CURSOR or button to specify the hourto stop, and press the ENTER button.

10Press the REC LEVEL/CURSOR or button to specify the min-utes, and press the ENTER button.

11Press the REC LEVEL/CURSOR or button to select the desiredfunction.

To select the timer playback source: CD, MD, TUNER or AUX.

To select the timer recording source: TUNER or AUX.

12Press the ENTER button.

13Press the REC LEVEL/CURSOR or button to adjust the volume.

� Be careful not to turn the volume up too high.

14Press the ENTER button.

Timer playback Timer recording

� The timer setting is displayed in order.

� The unit will enter the stand-by mode and then the playback or recording stand-by mode automatically.

When the preset time is reached, playback or recording will start.

� In timer playback, the volume will increase gradually. In timer recording, it will start with the volume you set.

When the timer end time is reached, the system will enter the power stand-by mode automatically.

TIMER


51

CX1H_UK49-59.fm00/12/17

Adv

ance

d F

eatu

res

Tim

er a

nd S

leep

Ope

ratio

n

� Using the same timer settingOnce memorised, the timer setting can be used as follows.

Notes:� The timer setting will be cleared when the unit is unplugged or the power failure

occurs.� The timer playback is possible with a CD or MD even if the repeat, random, or pro-

grammed playback is set.� When performing timer playback or recording using another unit connected to the

AUX INPUT sockets, select "AUX" in step 11. At this time, only this stereo systemwill be turned off automatically. (Another unit will not be turned off.)

To check the timer setting:

To change the timer setting:Perform "Timer playback/Timer recording" from the beginning. (See pages 49 -50).

To cancel the timer playback/timer recording:� If the power is turned on whilst in the playback or recording stand-by mode, the

timer setting will be cancelled.� Proceed as follows to cancel without turning the power on.


2 Within 10 seconds, press the REC LEVEL/CURSOR or buttonto select "STANDBY".

If "STANDBY" is not displayed, the clock setting has been cleared.

In this case, reset the clock and the timer.


The timer setting is displayed in order.

The unit will enter the stand-by mode and then the playback or recording stand-by mode automatically.

1 Whilst in the timer playback or timer recording stand-by mode, press the TIMER/DELETE button.

2 Within 10 seconds, press the REC LEVEL/CURSOR or button to select "TIMER CALL".


� After the timer setting is displayed in order, the display will return to normal.


2 Within 10 seconds, press the REC LEVEL/CURSOR or button to select "CANCEL".



52

CX1H_UK49-59.fm00/12/17

Adv

ance

d F

eatu

res

Tim

er a

nd S

leep

Ope

ratio

n

Timer and Sleep Operation (continued)

� Sleep operationThe radio, CD, and MiniDisc can all be turned off automatically.

To confirm the remaining sleep time:

� The display will return to normal after approximately 10 seconds.� You can change the sleep time.� Press the ENTER button whilst the sleep remaining time is displayed (see steps 5

- 6 on the left). To cancel the sleep operation:The sleep timer is cancelled when the unit enters the stand-by mode.To cancel only the sleep timer without setting the unit to the stand-by mode, proceedas follows.

1 Play back the desired sound source.


3 Within 10 seconds, press the REC LEVEL/CURSOR or buttonto select "SLEEP".


5 Press the REC LEVEL/CURSOR or button to specify the sleeptime.

(Maximum: 2 hours - Minimum: 1 minute)


7 Your system will enter the power stand-by mode automatically af-ter the preset time has elapsed.

� The volume will be turned down 1 minute before the sleep operation finishes.

1 Press the TIMER/DELETE button whilst the sleep timer is set.

2 Within 10 seconds, press the REC LEVEL/CURSOR or button to select "SLEEP".

Remaining sleep time

1 Press the TIMER/DELETE button whilst the sleep timer is set.

2 Within 10 seconds, press the REC LEVEL/CURSOR or button to select "SLEEP OFF".



53

CX1H_UK49-59.fm00/12/17

Adv

ance

d F

eatu

res

Tim

er a

nd S

leep

Ope

ratio

n

� To use sleep and timer playback in combi-nation

You can fall asleep to the radio and wake up with the sound from a CD.

� To use sleep and timer recording in combi-nation

You can fall asleep to the sound from a CD and record the desired station whilst youare sleeping.

1 Set the sleep time (steps 1 - 6, page 52).

2 Set the timer playback (steps 1 - 14, pages 49 - 50).

2. Timer playback setting1. Sleep timer setting

Timer playbackstart time

1 minute - 2 hours Desired time

Sleep operation willautomatically stop.

End time

1 Set the sleep time (steps 1 - 6, page 52).

2 Set the timer recording (steps 1 - 14, pages 49 - 50).

2. Timer recording setting1. Sleep timer setting

Timer recordingstart time

1 minute - 2 hours Desired time

Sleep operation willautomatically stop.

End time


54

CX1H_UK49-59.fm00/12/17

Adv

ance

d F

eatu

res

Enh

anci

ng Y

our S

tere

o S

yste

m

Enhancing Your Stereo SystemBefore connecting external units, set this unit to the stand-by mode and turn off thepower of the external units.

To the line output sockets

Commercially available RCA leadVCR, DVD, etc.


55

CX1H_UK49-59.fm00/12/17

Adv

ance

d F

eatu

res

Enh

anci

ng Y

our S

tere

o S

yste

m

� Listening to the playback sounds from VCR, DVD, etc.

� Recording on a MiniDisc (Sound synchro-nised recording)

� Recording on a MiniDisc (Normal record-ing)

� Headphones� Before plugging in or unplugging the headphones, reduce the volume.� Be sure your headphones have a 3.5 mm (1/8") diameter plug and are between 16

ohms and 50 ohms impedance. The recommended impedance is 32 ohms.� Plugging in the headphones disconnects the speakers automatically. Adjust the volume

using the VOLUME buttons.

1 Press the AUX (DEMO) button.

2 Play the connected equipment.

3 Adjust the volume using the VOLUME buttons.


2 Load a recordable MiniDisc into the MD compartment, label sideup.

3 Press the S-SYNC REC button on the remote control.


� Recording will start automatically.

� The recording level is the level adjusted in the previous recording. (This level can also be adjusted whilst recording.)


2 Load a recordable MiniDisc into the MD compartment, label sideup.

3 Press the REC button.


5 Press the or button to adjust the recording level.

Level meter Recording level

� Maximum level should not exceed "0dB".

� The recording level can be adjusted in 2dB intervals between -4dB and +10dB.

� If the recording level is too low, the sound volume will be decreased. If it is too high, the sound will be distorted.


0dB -4dB ··· +10dB


56

CX1H_UK49-59.fm00/12/17

Ref

eren

ces

Wha

t is

a M

iniD

isc?

/ M

iniD

isc

Sys

tem

Lim

itatio

ns

What is a MiniDisc?The disc is stored in a cartridge. You can handle it easily without worrying about dust, fin-gerprints, etc. However, dust entering the opening of the cartridge, dirt on the cartridge,warping, etc. may cause malfunctions. Please note the following.

� To prevent recorded MiniDiscs from being erased accidentally

Slide the accidental erase prevention tab, located on the side of the MiniDisc, in the direc-tion indicated by the arrow.� The MiniDisc is then be protected against accidental erasure.

To add a recording to such a MiniDisc, slide the accidental erase prevention tab back to itsoriginal position.

� Helpful tip when attaching a labelWhen attaching a label to a MiniDisc cartridge, be sure to note the following. If the label isnot attached properly, the MiniDisc may jam inside the unit and it may not be possible toremove it.

� Types of discs

MiniDisc System Limitations

� If the label peels off or partially lifts away, replace it with a new one.

� Do not put a new label on top of an existing one.� Attach the label only in the specified location.

There are two types of discs: playback-only and recordable types.� Playback-only MiniDisc: This type of MiniDisc is used for commercially available

prerecorded music. This is the same kind of optical disc as CDs. Playback is performed using an optical pickup. (Re-cording and editing are not possible.)

A Shutter will be used on only one side (back).

� Recordable MiniDisc: This is a "raw disc" on which recording can be performed.

A magneto optical disc is used. Recordings are made us-ing a laser and magnetic field. Repeated recording is pos-sible.

Shutters will be used on both sides.

Recordable Recordingprevented

Even if the maximum recording time of a MiniDisc has not been reached, "TOC FULL" may be displayed.

In the MD system, the delimiter of the recording area on a MiniDisc is programmed in a TOC. If partial erasing, recording and editing are repeated several times, TOC information will fill up, even though the number of tracks has not reached the limit (255 tracks), and further re-cording will be impossible. (If you use the all erase func-tion, this MiniDisc can be used from the beginning.)

Even if the maximum recording time of a MiniDisc has not been reached, "DISC FULL" may be displayed.

If there is any flaw on the MiniDisc, that part is automat-ically excluded from the space available for recording. Therefore, the recording time becomes shorter.

Even if several short tracks are erased, the remaining recording time may not show an increase.

When the remaining recording time of a disc is dis-played, short tracks less than 12 seconds long may not be included in the total.

Two tracks may not be com-bined in editing.

For MiniDiscs on which repeated recording and editing operations were performed, the COMBINE function may not work. A track recorded from a CD (digital recording) and a track recorded from a radio or other equipment (analogue recording) cannot be combined.

The total of the recorded time and time remaining on a disc may not add up to the maximum possible recording time.

A cluster (about 2 seconds) is normally the minimum unit of recording. So, even if a track is less than 2 sec-onds long, it will use about 2 seconds of space on the disc. Therefore, the time actually available for recording may be less than the remaining time displayed.

If there are scratches on discs, those sections will be au-tomatically avoided (no recording will be placed in those sections). Therefore, the recording time will be reduced.

If recorded tracks are fast re-versed or fast forwarded, the sound may skip.

A MiniDisc which has been recorded or edited repeated-ly may skip during fast reverse or fast forward.


57

CX1H_UK49-59.fm00/12/17

Ref

eren

ces

Err

or M

essa

ges

Error MessagesWhen an error message is displayed, proceed as follows:

Error messages Meaning Remedy

BLANK MD � Nothing is recorded. (Neither music nor disc name is re-corded.)

� Replace it with another disc.

Can't COPY � You tried to record from a copy prohibited CD.

� Replace the CD.

Can't EDIT � A track cannot be edited. � Change the stop position of the track and then try editing it.

Can't READ* � The disc is damaged. � Replace it with another disc.

(*: Number or symbol)

� TOC information cannot be read.

� Erase the disc and try recording again.

� MiniDisc not specified.

Can't REC � Recording cannot be per-formed correctly due to vibra-tion or shock in the unit.

� Re-record or replace the Mi-niDisc.

Can't T REC � Timer recording is impossible or there is no available space on the MD.

� Replace it with another recorda-ble disc.

� The disc is out of recording space.

Can't WRITE � The TOC information could not be created properly due to a mechanical shock or to scratches on the disc.

� Set this unit to the stand-by mode and try to write the TOC again. (Remove any source of shock or vibration whilst writing.)

CD NO DISC � A CD has not been loaded. � Load a CD.

� The CD data cannot be read. � Reload the CD.

DISC FULL � The disc is out of recording space.

� Replace the disc with another recordable disc.

EDIT OVER � You chose 21 or more tracks for track editing.

� Decrease the number of tracks.

Er - MD ** � A MiniDisc is not working properly.

� Press the MD button.

(**: Number or symbol)

� Set this unit to the stand-by mode and turn the power on again.

Error messages Meaning Remedy

MD NO DISC � A MiniDisc has not been load-ed.

� Load a MiniDisc.

� The MiniDisc data cannot be read.

� Reload the MiniDisc.

NAME FULL � The number of characters for the disc name or track name exceeds 40.

� Shorten the disc or track name.

NOT AUDIO � The data recorded on this disc is not audio data.

� Replace the disc.

PLAYBACK MD � You tried to record on a play-back-only disc.


POWER ? � A MiniDisc is not working properly.

� Set this unit to the stand-by mode and turn the power on again.

PROTECTED � The disc is write protected. � Move the write protection tab back to its original position.

TEMP OVER � The temperature is too high. � Set this unit to the stand-by mode and wait for a whilst.

TOC FORM ** � TOC information recorded on the MD does not match the MiniDisc specifications or it cannot be read.

� Replace it with another disc.

(**: Number or symbol)

� Erase the disc and try recording again.

TOC FULL � There is no space left for re-cording track numbers.


TOC FULL 1 � There is no space left for re-cording character information.


� Erase the needless characters.

? MD DISC � The data contains an error. � Press the MD button.

� MiniDisc not specified. � Replace it with another disc.


58

CX1H_UK49-59.fm00/12/17

Ref

eren

ces

Trou

bles

hoot

ing

Cha

rt

Troubleshooting ChartMany potential "problems" can be resolved by the owner without calling a servicetechnician.

� General

� CD player

� MiniDisc

� Tuner

� Remote control

Symptom Possible cause

� "TIME ADJUST" appears when the clock time is checked.

� Did a power failure occur? Reset the clock. (Refer to page 17.)

� When a button is pressed, the unit does not respond.

� Set this unit to the power stand-by mode and then turn it back on.

� No sound is heard. � Is the volume level set to "0"?

� Are the headphones connected?

� Are the speaker wires disconnected?

� The picture on the TV screen is dis-torted.

� When a radio or TV which uses an indoor aerial is placed near the unit, the picture on the TV screen may be distorted or the radio may not function properly.

� It is recommended that you use an external aerial.


� Even though a disc has been loaded, "CD NO DISC" or "Can't READ" is displayed.

� The disc is very dirty.

� Is the unit located near excessive vibrations?

� Has condensation formed inside the unit?

� Playback does not start. � The disc is loaded upside down.

� Playback stops in the middle or is not performed properly.

� The disc does not satisfy the standards.

� The disc is distorted or scratched.

� Playback sounds are skipped, or stopped in the middle of a track.



� Has condensation formed inside the unit?


� A recording cannot be made. � Is the MiniDisc protected against accidental erasure?

� Did you try to make recording on a playback-only MiniDisc?

� Can you see the "DISC FULL" or "TOC FULL" message in the display?

� Even though a disc has been loaded, "MD NO DISC" or "Can't READ" is displayed.



� Playback sounds are skipped. � Has condensation formed inside the unit?


� Radio makes unusual noise consec-utively.

� The stereo system is placed near the TV or computer.

� FM/AM loop aerial is not placed properly. Move the AC power lead away from the aer-ial if located near.

� The preset channel cannot be re-called.

� Did a power failure occur?

� Preset the channel again.


� The remote control does not oper-ate.

� Is the AC power lead of the stereo system plugged in?

� The battery polarity is not correct.

� The batteries are dead.

� Incorrect distance or angle.

� Does the remote control sensor receive strong light?


59

CX1H_UK49-59.fm00/12/17

Ref

eren

ces

Trou

bles

hoot

ing

Cha

rt

� If trouble occurs (reset)When this product is subjected to strong external interference (mechanical shock,excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it isoperated incorrectly, it may malfunction.

If such a problem occurs, do the following:Unplug the power lead from the AC socket. Then, plug it in again and retry theoperation.

Caution:This operation will erase all data stored in memory including clock, timer settings,tuner preset, and CD or MiniDisc programme.

� Condensation

� Before transporting the unitRemove the CD and MiniDisc from the unit. Your unit checks whether there are anydiscs inside. "CD NO DISC" and "MD NO DISC" appear if no disc is inside. Then, setthe unit to the power stand-by mode. Carrying the unit with discs left inside can dam-age it.

Sudden temperature changes, storage or operation in an extremely humid environ-ment may cause condensation inside the cabinet (CD pickup, MD pickup, etc.) or on the transmitter on the remote control.Condensation can cause the unit to mal-function. If this happens, leave the power on with no disc in the unit until normal playback is possible (about 1 hour). Wipe off any con-densation on the transmitter with a soft cloth before operating the unit.


60

CX1H_UK60-61.fm00/12/18

Ref

eren

ces

Mai

nten

ance

/ S

peci

ficat

ions

Maintenance� Cleaning the CD pickup lens� Do not touch the CD pickup lens. If fingerprints or dust accumulate on the pickup,

clean it gently with a dry cotton swab.

� Cleaning the cabinetPeriodically wipe the cabinet with a soft cloth and a diluted soap solution, then with adry cloth. Caution:Do not use chemically treated cleaning cloths or other chemicals.

SpecificationsAs part of our policy of continuous improvement, SHARP reserves the right to make designand specification changes for product improvement without prior notice. The performancespecification figures indicated are nominal values of production units. There may be somedeviations from these values in individual units.

� General

� Amplifier

� CD player

Pickup (Lens) Power source AC 230 V, 50 Hz

Power consumption Power on: 42 W

Power stand-by: 0.6 W (*)

Dimensions Width: 330 mm (13") Height: 208 mm (8-3/16") Depth: 190 mm (7-1/2")

Weight 5.0 kg (11 lbs.)

( * ) This power consumption value is obtained when the demonstration mode is can-celled in the power stand-by mode. Refer to page 14 to cancel the demonstration mode.

Amplification system 64fs 1-bit switching

(Remarks: fs = 44.1 kHz)

Rated output power RMS: 40 W (20 W + 20 W) (DIN 45 324)

A/D noise shaping 7th-order (delta - sigma) modulation

Output terminals Speakers: 6 ohms

Headphones: 16 - 50 ohms (recommended: 32 ohms)

Input terminals Auxiliary: 500 mV/47 kohms

Type 1-disc vertical compact disc player

Signal readout Non-contact, 3-beam semiconductor laser pickup

D/A converter 1-bit D/A converter

Frequency response 20 - 20,000 Hz

Dynamic range 90 dB (1 kHz)


61

CX1H_UK60-61.fm00/12/18

Ref

eren

ces

Spe

cific

atio

ns

� MiniDisc

� Tuner

� SpeakerType MiniDisc Recorder

Signal readout Non-contact, 3-beam semiconductor laser pickup

Rotation speed 400 - 900 rpm CLV, Approx.

Error correction ACIRC (Advanced Cross Interleave Reed-Solomon Code)

Quantization 20-bit linear (A/D converter)

Coding ATRAC (Adaptive TRansformed Acoustic Coding), ATRAC 3

Sampling frequency 44.1 kHz

Recording method Magnetic modulation overwrite method

Frequency response 20 - 20,000 Hz

D/A converter 1-bit D/A converter

Wow and flutter Unmeasurable (less than 0.001% W. peak)

Signal/noise ratio 95 dB (1 kHz)

Dynamic range 90 dB (1 kHz)

Audio channel Stereo: 2 channels (SP, LP2, LP4)

Monaural: 1 channel (MONO)

Frequency range FM: 87.5 - 108 MHz

AM: 522 - 1,620 kHz

Type 2-way type speaker system

2 cm (13/16") Tweeter

12 cm (4-3/4") Woofer

Maximum input power 40 W

Rated input power 20 W

Impedance 6 ohms

Dimensions Width: 170 mm (6-3/4") Height: 300 mm (11-13/16") Depth: 186 mm (7-3/8")

Weight 2.0 kg (4.4 lbs.)/each


TINSE0352AWZZA0012.YT

TERMS OF GUARANTEE

Sharp Electronics (UK) Ltd. (“Sharp”) guarantees to provide for the repair, or at its option the replace-ment, of this product subject to the conditions listed below:-

1. This guarantee shall only apply to faults which are due to inferior workmanship or materials. It doesnot cover faults or damage caused by accident, misuse, fair wear and tear, neglect, tampering withthe product, or repair other than by a Service Facility appointed by Sharp.

2. As this product is intended for private domestic use only, the guarantee will not apply if the productis used in the course of a business, trade or profession.

3. To benefit from this guarantee, any fault which occurs must be notified to Sharp, or its appointedService Facility within one year from the date this product was purchased. Proof of purchase mustbe provided.

4. The guarantee does not cover carriage costs, jewelled styli, audio tapes, compact discs or batter-ies.

5. In the unlikely event of this product requiring repair, please contact the supplier from whom it waspurchased. Where this is not possible, please contact the Sharp Customer Information Centre onthe telephone number given below.

6. No person has any authority to vary the terms or conditions of this guarantee.

7. This guarantee is offered as an additional benefit to your statutory rights, and does not affect theserights in any way.

If you have any difficulty operating this product, or would like information on other Sharp products,please telephone the Sharp Customer Information Centre on the number given below.

Sharp Customer Information Centre - Telephone 08705 274277

SHARP ELECTRONICS (U.K.) LTD.Sharp House, Thorp Road, Newton Heath, Manchester, M40 5BE

SHARP CORPORATION


operation manual sd-cx1h - minidisc

Documents