Copyright 2006 - Stay Tooned, Inc. All rights reserved worldwide.

This book, or portions of it, may not be duplicated, resold, or redistributed in any way, without the expressed written consent of Stay Tooned, Inc.

TABLE OF CONTENTS 2INTRODUCTION 3SUPPLIES: WHAT YOURE GOING TO NEED 4STEP 1: CUTTING THE WOOD BASES TO THE RIGHT LENGTH 6STEP 2: CUTTING THE DOWELS TO THE RIGHT LENGTH 7STEP 3: DRILLING THE ARM HOLES 8STEP 4: DRILLING THE MOUNTING SCREW HOLES 10STEP 5: INSERTING THE DOWELS 13STEP 6: CUTTING AND DRILLING THE RUBBER PIECES 14STEP 7: PAINTING THE WALL HANGERS 15STEP 8: MOUNTING YOUR HANGERS TO THE WALL 16THE FINISHED PRODUCT 19CREATING YOUR OWN WALL OF GUITARS 20OTHER STUFF FROM PAINTYOUROWNGUITAR.COM 21

TABLE OF CONTENTSMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

2

As the guy behind PAINTYOUROWNGUITAR.COM and someone whosbeen painting guitars for over 20 years, I have more guitars and more guitar parts than you could imagine.

Although a lot of my guitars are in cases, I do have roughly 30 or so hang-ing up on the walls of my guitar room.

Rather than spend $10 - $15 for professional guitar wall hangers (whichtruthfully, are well constructed and probably worth the money), Im justsuch a do-it-yourselfer, that Id rather not spend $300 on hangers. For me,paying less than $1.00 per hanger is much more appealing!

And, thats what this e-book is all about.

Follow along and Ill show you how I make a very sturdy guitar hanger inless than 5 minutes and for less than $1.00 per hanger.

With the money youll save...shoot - you could probably buy another guitarfor your collection!

In all seriousness, you dontneed any special skills tomake these wall hangers;all you need are a few com-mon tools.

I show you the exact sup-plies youll need, the tools,and the measurements.

ANYONE CAN DO THIS.

Okay - lets get started!

INTRODUCTIONMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

3

FIG 1 shows the finished wall hanger without paint.

Heres a list of items I used to make my Guitar Wall Hangers. You needthe first 6 items in order to do it right.

1. 1 Wood - I found this piece of wood(see FIG 2) in the area that youll findround dowels in your local hardwarestore. I bought these pieces from Lowes,but Ive also seen them at ACEHardware, as well as Home Depot.

Its 1 in width and the length youllneed for each of your wall hangers isroughly 4. You can make each longer,but its not necessary. One piece thats3 ft. long will be enough to make 8hangers - which is what I did.

Buy your wood from HOME Depotrather than ACE Hardware - youll payhalf the price.

2. 3/8 Oak Dowel - I recommendusing an oak dowel (see FIG 2)because its a very strong wood.

3. Tape Measure (or Ruler) and aPencil - You need one or the other tomake accurate measurements and apencil to mark your cuts.

4. Drill Press or Power Drill - I usedmy drill press (see FIG 4), but youreonly drilling 4 holes, so you could easilyuse a power drill and do it by hand.

5. Hand Saw or Miter Saw - I used aMiter Saw to cut my pieces to length,but you can easily cut your pieces tothe length with a hand saw like theones seen in FIG 5.

6. Wood screws - if you are screwingdirectly into a stud or solid wood, use ascrew that is at least 2.5 long. If youare NOT screwing directly into wood,but rather, a wall (which is drywall and

SUPPLIES: WHAT YOURE GOING TO NEEDMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

4

FIG 2

FIG 3

FIG 1

FIG 4

possibly plaster), youll need someheavy duty drywall anchors. I recom-mend using something like EZ ANCOR(see FIG 6). Choose the one that cansupport up to 20 lbs. or more. Youll bedrilling two holes to keep your wallhanger in place, so these will hold theweight of your guitar without a problem.

OPTIONAL ITEMS

7. Paint - You can leave your wallhangers as bare wood, but if youdecide to finish them with paint, a flatblack may look best. KrylonsInterior/Exterior Flat Black will worknicely.

6. Rubber Bungy - I live in California -the land of earthquakes, so althoughthe guitars sit nicely on the holders, Ithought it was best to place a piece ofrubber over the dowels - just in case weget a few strong tremors. The rubberwill prevent the guitars from falling offthe dowel/arms. I bought one bungycord and cut it into several pieces.

7. Wood File and Fine Sandpaper - Ididnt bevel the edges of the wood, butthats something you can definitely do, ifyou want. After beveling the edges, takesome fine sandpaper to make it niceand smooth.

8. Level - I used a level to make surethat my wall hangers were perfectly 90.

And thats the list.

SUPPLIES: WHAT YOURE GOING TO NEEDMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

5

FIG 7

FIG 6

FIG 5

FIG 8

To begin, I measured 4 from the end ofmy piece of wood.

I marked this measurement with a pencil.

Using my miter saw, I made my cut (seeFIG 9). Keep in mind, this cut can easilybe made with any type of hand saw, souse whats at your disposal.

If you plan on making a whole bunch ofthese wall hangers, which is what I rec-ommend you do, have your ruler ortape measure, and pencil handy, so youcan measure, cut, measure, cut, etc. Inno time, youll have 8 bases cut andready to go.

When youve made all of your cuts,youre ready to move to Step 2.

STEP 1: CUTTING THE WOOD BASES TO THE RIGHT LENGTHMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

6

FIG 10

FIG 9

FIG 11

If all you had were Strats with a non-angled headstock, you could cut all ofyour dowel pieces to 3.5 in length.

However, if you have some Les Pauls, then, because of the headstocks angledheadstock, youll need to cut some of the dowels to 4.5 to compensate.

So, once again, measureyour length - 3.5 for Strats(or non-angled headstocks),4.5 for LPs, mark it with apencil, then cut.

FIG 12 shows all of mydowel pieces cut. (I cutsome other longer piecesfor my Les Pauls.)

When all of your pieceshave been cut, youre readyto move on to Step 3.

STEP 2: CUTTING THE DOWELS TO THE RIGHT LENGTHMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

7

FIG 12

For this step, youre going to drill twoholes for the arms.

Measure 7/8 from each end of your 4base and mark it with a pencil as Ivedone in FIG 13.

When youve marked each end, thisshould give you a width of roughly 2 foryour neck to sit in. This is enough roomto hold the neck by the headstock for Strats and Les Pauls without a problem.

Once you have your measurements, follow that up with finding the middleof your base which will be 1/2. Make a mark at each end and draw a lineacross as Ive done in FIG 14. Youve now found the center points for eachof the arms.

To make an indent in the wood whereyou want to drill, you can either use acenter punch as Im doing in FIG 15, oryou can use a regular nail. Either way,mark the center point so that itll beeasier for you to line up your drill bitwith the center point.

Using either a drill press or a hand drill,drill right through your base using a 3/8drill bit. Make sure that your bit is sharp- for a nice, clean cut (see FIG 16).

To avoid having your wood splinter likethe one pictured in FIG 17, you caneither A: exit out of the bottom veryslowly B: place your base on top of

STEP 3: DRILLING THE ARM HOLESMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

8

FIG 13

FIG 14

IMPORTANT POINT: If youre making a hanger for a Tele, the space foryour neck to sit in will have to be less than 2 to compensate for the smallheadstock. That means, you can either make your base less than 4, andstill measure 7/8 from each end, or you will measure in from each edge1 - instead of 7/8. To be certain about the width youll need, carefullymeasure your Tele neck, or any other neck youre going to hang to get aperfect measurement for that specific neck.

FIG 15

another piece of wood, then drill yourholes making sure your drill bit passesthrough your base, and slightly into thewood underneath, or C: use a drill bitwith a long point such as the one in FIG23. Once you feel the point exit out ofthe bottom, flip your base over and con-tinue to drill the hole through using thehole on the bottom as your center point.Personally, I use option B.

The one in FIG 17 is the worst of all ofthem that I drilled and I did this on pur-pose to show you that this can and willhappen - and to offer a way to prevent it.

All of the options above will reduce andeliminate splintering, but resting thebase on top of another piece of wood is probably the best option.

Once your holes for the dowels/arms have been drilled, you can move toStep 4 - drilling the holes for the screws.

STEP 3: DRILLING THE ARM HOLESMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

9

FIG 16

FIG 17

There are two options for drilling mounting screw holes; the first option isfor Les Paul-style guitars - where the headstock is perfectly symmetrical -the same on both sides. The second option is for headstocks like a strato-caster or explorer - where each side of the headstock is completely differ-ent.

OPTION 1 - Symmetrical Headstock

For this step, youre going todrill two holes. If you choose,you can also drill a half-hole,as I did in FIG 18, to counter-sink the head of the screw, butits not absolutely necessary.

To start, find the center of your4 base - which will obviouslybe 2. Mark the center with apencil as Ive done in FIG 19.From there, place a ruler onthat center mark and mark off1/2 on both sides, so you nowhave a measurement of 1(see FIG 20).

When choosing a drill bit forthe screw holes thatll mountthe wall hanger to the wall,choose a bit that is slightlylarger in width than yourscrew. You want your screw tobe able to pass through thebase without getting hung upin it. But at the same time, youdo want it to be tight. So,choose a drill bit that is JUSTa bit wider than your screw.

Once again, use a centerpunch to make a small indentin the wood on the center pointof the hole before drilling yourscrew holes.

STEP 4: DRILLING THE MOUNTING SCREW HOLESMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

10

FIG 19

FIG 18

FIG 20

Using your drill press or powerdrill, line up the point of yourdrill bit with your center punchhole and drill right throughyour base. Exit your drill bitslowly, or place your base ontop of another piece of wood, ifyoure concerned with thewood splintering underneath.

When youre done, your baseshould look like mine in FIG 21.

If you wish to countersink thehead of your screw rather thanhave it sit above the base ofyour hanger like Ive done inFIG 22, then I started with adrill bit that was slightly largerthan the screwhead and drilledthat hole first as seen in FIG22. I went down about 1/4.

The drill bit I used has a verysharp point, so its perfect forthis usage; it leaves a centerpoint as a guide (see FIG 22and 23). To make the holes forthe screws, its just a matter ofswitching drill bits and drillingthe holes for the screws usingthe center hole guide left bythe bigger drill bit (see FIG 22).

If you dont have a drill bit witha point like the one in FIG 23,then I would suggest that youdrill the hole for the mounting screw first, then drill the hole to countersinkthe screw head last.

OPTION 2 - Non-Symmetrical Headstock

If youre going to make wall hangers for guitars such as a stratocaster, an

STEP 4: DRILLING THE MOUNTING SCREW HOLESMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

11

FIG 22

FIG 23

FIG 21

If you dont countersink the holes for your screws, yourwall hanger should look like this.

explorer, or any other guitar that has a headstock that is non-symmetrical,you will have to angle the base of the wall hanger on the wall to compen-sate for the imbalance.

However, finding just the right angle can be tough when using two screwsto mount it to the wall. So, for guitars such as these, I drill only one hole -dead-center (see FIG 24). Thisallows me to pivot the baseand to get just the right anglefor each guitar. Once I havethe right angle, I tighten myscrew and its done. More onthis in a few minutes.

When making wall hangers forguitars with non-symmentricalheadstocks, follow the sameprocedure for symmetricalheadstocks - just substitutetwo screws 1 apart for onescrew dead-center.

Finishing Up

When I was all done drillingmy mounting screw holes, Ihad eight bases for Les Paulsall ready to go (see FIG 25).

This took me about 20 minutesto do, but thats also because Iwas taking photos along the way. I imagine if I wasnt snapping photos, Iwouldve had them done in 15 minutes or less.

When youve got all of your holes drilled, its time to move to Step 5 -inserting your dowels.

STEP 4: DRILLING YOUR MOUNTING SCREW HOLESMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

12

FIG 24

FIG 25

I used 3/8 dowels and by using a drill press, I got perfect 3/8 holes. Butthat also means that the fits going to be TIGHT... but, thats good.

To get the dowels into the holes, I start by trying to push both of them in byhand. When Ive pushed them in as far as I can, I use a piece of wood anda rubber mallet to hammer them into their holes all the way (see FIG 26).

The piece of wood is sitting flatalong the tops of the dowelsand I tend to hammer the cen-ter of the piece of wood so thatboth dowels go in at the sametime. I make sure that eachdowel sits flush on the bottomand that both are the samedistance in and out.

If you do an accurate job ofdrilling your holes, you wontneed to glue these in at all.The fit is extremely TIGHT.

When youve completed this,its on to Step 6.

STEP 5: INSERTING THE DOWELSMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

13

FIG 26

FIG 27

This step is totally optional. I only added the bungy rubber over my hang-ers arms just to be safe - in case of an earthquake. You dont have to do itif you dont want to.

FIG 28 shows a bungy cord cut up into pieces roughly 4 wide. I markedthe length with a pencil and then used an ordinary pair of scissors to makeeach cut.

When drilling the holes into the bungy, Imade my second hole slightly narrowerthan the hangers arms, so Id have tostretch the bungy just a little to get it on.This makes it a nice, tight fit.

Once the holes were drilled, they slidover the hangers arms very nicely (seeFIG 29).

An option to using this bungy cordwould be to use a rubber band. Whendoing a search online, I found a fewonline retailers that sold black rubberbands for a very cheap price. Thosewould be a good alternative.

When youre done, its on to Step 7.

STEP 6: CUTTING AND DRILLING THE RUBBER PIECESMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

14

FIG 29

FIG 28

PLEASE NOTE: I actually cut all of these pieces at the same time I wascutting and drilling the wood pieces. You can do all of it at the sametime, or you can do this step after all of the wood pieces are cut.

Once again, this step is completely optional. If you like the look of the barewood, you can leave them as is. Ive made several of these wall hangers.Some were left as is while others were painted flat black like the onesseen here.

Painting Your Wall Hangers

For these wall hangers, I used KrylonInterior/Exterior Flat Black to finishthem.

Before I start, I insert a screw into thebottom of the hanger and wear an oldrubber glove to keep me from paintingmy entire hand black (see FIG 30).

FIG 30 shows a wall hanger after onecoat of thin flat black. It usually takesjust two thin coats to get a nice, solid black.

I like to paint it all in one application if I can, so the screw helps me torotate it in my hand and get all of the recesses.

When spraying your paint, hold your can at least 10 away from the wallhanger. Between coats, I rest the hanger on a table. I leave the screwinserted, so half of the hanger is hanging off of the table.

I wait roughly 10 minutes between coats. After two coats have beenapplied, I wait one hour before handling it.

When all of your hangers have been painted, and youve given them atleast an hour to dry, you can move on to Step 8.

STEP 7: PAINTING THE WALL HANGERSMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

15

FIG 30

Now that our hangers are done, its time to mount them.

Before we start drilling, there are a few things you need to know: whenscrewing into a wall and not into a stud, youll need to use heavy-duty dry-wall anchors to help support the weight. EZ Ancors, which are the ones Iuse (see SUPPLIES YOULL NEED), can hold up to 20 lbs of weight perancor (some hold less, so choose the right one), so when using two closetogether (an inch apart), theyll support the weight of the guitar very well.

For the wall hangers that you make for guitars with non-symmetrical head-stocks such as a stratocaster, use the EZ Ancors that can support up to 50lbs.

EZ Ancor supply you with a screw, however, because the screws have topass through the base (3/4 if you countersunk your hole - 1 if you didntcountersink), they wont be long enough. So, just pay a visit to your localACE hardware store (or LOWEs or HOME Depot), and buy some 2.5screws.

Another thing to consider is the placement of wall studs in a typical home.Normally, they are spaced 19 apart. Most guitars are about 12 - 14 inwidth. So, if you really wanted to screw your wall hangers into a wall stud,once you find one, you should be able to locate the others using the 19measurement. (this is a general contractors rule, but not all contractorsswear by it, so use a wall stud finder just to be certain.)

At the end of this book, I give the measurements I used to create my wallof guitars. You can use this as a guide to help you create a similar wall.

Mounting A Wall Hanger For A Guitar With A Symmetrical Headstock

Once youve decided where youwant to place your first wallhanger, use a stud finder todetermine if youre going to bedrilling into a stud or into drywall.When youve made that determi-nation, put a piece of maskingtape down on the wall as Ivedone in FIG 31.

Using a level, I drew a straightline across, then used a ruler to

STEP 8: MOUNTING YOUR HANGERS TO THE WALLMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

16

FIG 31

measure 1/2 on both sides of my center point. I marked those points with acenter punch (see FIG 32). Now, I have my marks for where I need to drill.

For this wall, there is a plywood wall directly behind the drywall, so all ofmy hangers will be going intowood rather than having to usethe EZ Ancors. Nonetheless, theEZ Ancors are extremely sturdy,so using them is just as good asdrilling into a stud - or a plywoodwall.

Using my drill, I drilled themounting holes using a drill bitthats the same thickness as theshaft of my screw (The white linein FIG 33 shows the thickness ofthe drill bit I used). This allowsthe screw to go in easily andallows the thread to grip andhold the hanger in place.

When both holes were drilled, Iinserted the screws into theholes on the wall hanger andpositioned the wall hanger intoposition. I screwed each screwin fairly deep (see FIG 34).

However, before final tightening,I got out a small level and madesure that the wall hanger wasperfectly level before I secured itfor good (see FIG 35).

Moving to wall hangers for gui-tars with non-symmetrical head-stocks such as strats, I find thelocation on the wall where I wantmy wall hanger to sit.

I place a piece of masking tapedown in that location, then mark

STEP 8: MOUNTING YOUR HANGERS TO THE WALLMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

17

FIG 32

FIG 34

FIG 35

FIG 33

the center point on the wall.

I drill just one mounting screwhole for that wall hanger.

I place a screw into the hole onthe wall hanger and screw it intoplace so that its tight but notfully tightened (see FIG 36).

I then grab the guitar thatsgoing to hang on that wall hang-er and put it in place. Then, Iadjust the position of the wallhanger until the guitar is hangingperfectly.

I then remove the guitar andgive the wall hanger a final tight-ening so it cant move.

And, thats all there is to it!

Once youve done one of each,youll get the hang of it and youllhave no problem doing as manyas you need.

Remember that if youre screwinga wall hanger for a non-symmetri-cal headstock into drywall, makesure that you use the EZ Ancorsthat can support up to 50 lbs.

STEP 8: MOUNTING YOUR HANGERS TO THE WALLMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

18

FIG 36

FIG 37

IMPORTANT: As a precaution, when hanging Les Pauls, make sure thatyou hang them so they sit close to the wall and not out hanging close tothe ends of the dowels. These wall hangers are sturdy and so are theoak dowels, but Les Pauls are heavy, so you dont want to risk havingthe weight of the guitar snap the dowels.

THE FINISHED PRODUCTMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

19

This wall is a mixture of my own wall hangers and some profession wallhangers that cost $15 each. It was after I bought five of the professionalhangers that I decided to start making my own.

CREATING YOUR OWN WALL OF GUITARSMAKE YOUR OWN GUITAR WALL HANGERS IN LESS THAN 5 MINUTES AND FOR LESS THAN $1.00!

20

For my wall, Im fortunate in that I have a high ceiling in my guitar room -13ft. high ceilings, so I was able to hang two guitars per row - and offsetthem.

If you have a ceiling thats at least 7 ft. high, you should be able to alsohang two guitars per row.

1. I hung my wall hangers with a space of 45 between the top hanger andthe one that sat below it. If your ceiling is 7 ft. high, youll need to tightenup that space to about 41. Most guitars are roughly 39 long, so that givesyou just enough room. However, my numbers are estimates, so double-check your guitars for length to determine if you can hang one on top ofanother.

2. I positioned my wall hangers 14.5 apart. This allowed plenty of roombetween each guitar.

3. I offset the guitars by 16.5 simply because of the height of my ceiling.You may not be able to do that, so if you have to hang them side-by-side,you may want to allow for a little extra space between the guitars. Insteadof 14.5, you may want to do something like 16 apart.

21

OTHER STUFF FROM PAINTYOUROWNGUITAR.COM

The PAINT YOUR OWN GUITAR Book Series

www.paintyourownguitar.com/dvds.html

www.paintyourownguitar.com/guitars.html

These books are available in both e-books and hard copies through my website.

DVD Series