panel antennas - amphenol · pdf filetwinline april 2015 | 23 quad antennas with two multiband...
TRANSCRIPT
PANEL ANTENNASWITH TWO LOW BAND ARRAYS
22 | April 2015
TwinLine
April 2015 | 23
Quad antennas with two multiband arrays housed in an optimally designed package for low windload. Ideal for site/technology sharing.
Ordering Options Model Number
Manual Electrical Tilt 5980300
Remote Electrical Tilt AISG1.1 5980300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5980300G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5980300DG
Access Ports Description (Connectors)
This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded connectors located at the bottom face. See image on the following page.
Ultra Low Band 698-960 MHz Ports (4x) 7/16-DIN Female Long Neck
Ultra Wide Band Bottom System 1695-2690 MHz Ports (4x) 7/16-DIN Female Long Neck
Ultra Wide Band Top System 1695-2690 MHz Ports (4x) 7/16-DIN Female Long Neck
Electrical Characteristics R1-R2 Y1-Y3 (Bottom) Y2-Y4 (Top)
Frequency Bands (MHz) 700 800 900 1800 2100 2600 1800 2100 2600
Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value
15.515.515.2
16.516.416.2
17.417.317.0
17.117.117.1
17.517.517.4
18.018.017.8
17.117.117.1
17.517.517.4
18.018.017.8
Input Impedance 50Ω 50Ω 50Ω
VSWR < 1.5 < 1.5 < 1.5
Polarisation ±45° ±45° ±45°
Horizontal Beamwidth (-3 dB) 75° 68° 65° 65° 63° 61° 65° 63° 61°
Vertical Beamwidth (-3 dB) 8.6° 7.5° 6.7° 7.0° 6.4° 5.2° 6.5° 5.9° 4.7°
Electrical Downtilt Range 0-10° 0-12° 0-12°
Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical 18 dB Typical
Front-to-Back Ratio
@ 180°@ 180° ±30°
> 30 dB> 25 dB
> 30 dB> 25 dB
> 30 dB> 25 dB
Maximum Power (Per Port) 250 W 200 W 200 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
(2x) 698-960 / 1695-2690 / 1695-2690 MHz
59803005980300A 5980300G 5980300DG
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 18.0 / 18.0 dBi | Variable Tilt
• Twin tri band antenna, dual polarisation, 12 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°• Lightweight TwinLine platform with multi-array capability • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)
OPTIMAL PROFILE - LOW WINDLOAD
R1 R2
Y2 Y4
Y1 Y3
24 | April 2015
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
59803005980300A 5980300G 5980300DG
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 18.0 / 18.0 dBi | Variable Tilt
(2x) 698-960 / 1695-2690 / 1695-2690 MHz
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2683 x 432 x 153 mm
Weight (Excluding Mounting Accessories) 48 kg
Shroud Outdoor Fibreglass, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 150 km/h Frontal: 990 N Lateral: 555 N Rear: 920 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
Location of the MDCU or MDDUfor RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 698-960 MHz
YELLOW 1695-2690 MHz
Packaging
Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 59 kg Includes 0900181/00 Kit
April 2015 | 25
(2x) 790-960 / 1710-2170 / 2500-2690 MHz
59822005982200A 5982200G
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.3 / 17.6 dBi | Variable Tilt
• Twin tri band antenna, dual polarisation, 12 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°
• MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
Ordering Options Model Number
Manual Electrical Tilt 5982200
Remote Electrical Tilt AISG1.1 5982200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5982200G
Access Ports Description (Connectors)
This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded connectors located at the bottom face. See image on the following page.
RED and GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck
YELLOW Rings High Band (Top Array) 2500-2690 MHz Ports (4x) 7/16-DIN Female Long Neck
BLUE Rings High Band (Bottom Array) 1710-2170 MHz Ports (4x) 7/16-DIN Female Long Neck
Electrical Characteristics Low Band (RED or GREEN) High Band (BLUE) High Band (YELLOW)
Frequency Bands (MHz) 790...880...960 1710...1880 1900...2170 2500...2690
Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value
16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4
16.5...16.916.4...16.716.3...16.5
16.9...17.316.7...17.216.5...17.0
17.4...17.817.3...17.717.2...17.5
Input Impedance 50Ω 50Ω 50Ω
VSWR < 1.5 < 1.5 < 1.5
Polarisation ±45° ±45° ±45°
Horizontal Beamwidth (-3 dB) 75°...68°...63° 65° 62° 60°
Vertical Beamwidth (-3 dB) 7° 7° 5°
Electrical Downtilt Range 0-10° 0-12° 0-12°
Intra Band Isolation > 30 dB> 28 dB from 0° to 2° tilt
> 30 dB> 28 dB from 0° to 2° tilt
> 30 dB> 28 dB from 0° to 2° tilt
Isolation Between Bands 45 dB Typical 45 dB Typical 45 dB Typical
Isolation Between Left & Right Arrays > 30 dB > 30 dB > 30 dB
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical 18 dB Typical
Front-to-Back Ratio > 30 dB > 30 dB > 30 dB
Maximum Power (Per Port) 200 W 160 W 160 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET Module Part Number(one per antenna)
MDCU-A0000 for AISG1.1 protocol (one unit included in 5982200A)
MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5982200G)
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
LTE 800 ReadyLTE 2600 Ready
26 | April 2015
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2700 x 442 x 152 mm (219 mm with Rear Connectors)
Weight (Excluding Mounting Accessories) 56 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 160 km/h Frontal: 1300 N Lateral: 220 N Rear: 1700 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets Not available ---
(2x) 790-960 / 1710-2170 / 2500-2690 MHz
59822005982200A 5982200G
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.3 / 17.6 dBi | Variable Tilt
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
Packaging
Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 | 70 kg
RED 790-960 MHz
GREEN 790-960 MHz
BLUE 1710-2170 MHz
YELLOW 2500-2690 MHz
April 2015 | 27
(2x) 790-960 / 1710-2170 / 2500-2690 MHz
5982200 lv (lightweight version)5982200A lv 5982200G lv 5982200DG lv
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.3 / 17.6 dBi | Variable Tilt
• Twin tri band antenna, dual polarisation, 12 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°• Lightweight TwinLine platform with multi-array capability • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)
Ordering Options Model Number
Manual Electrical Tilt 5982200 lv
Remote Electrical Tilt AISG1.1 5982200A lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5982200G lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22) 5982200DG lv
Access Ports Description (Connectors)
This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded connectors located at the bottom face. See image on the following page.
RED and GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck
YELLOW Rings High Band (Top Array) 2500-2690 MHz Ports (4x) 7/16-DIN Female Long Neck
BLUE Rings High Band (Bottom Array) 1710-2170 MHz Ports (4x) 7/16-DIN Female Long Neck
Electrical Characteristics Low Band (RED or GREEN) High Band (BLUE) High Band (YELLOW)
Frequency Bands (MHz) 790...880...960 1710...1880 1900...2170 2500...2690
Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value
16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4
16.5...16.916.4...16.716.3...16.5
16.9...17.316.7...17.216.5...17.0
17.2...17.617.1...17.517.0...17.3
Input Impedance 50Ω 50Ω 50Ω
VSWR < 1.5 < 1.5 < 1.5
Polarisation ±45° ±45° ±45°
Horizontal Beamwidth (-3 dB) 75°...68°...63° 65° 62° 60°
Vertical Beamwidth (-3 dB) 7° 7° 5°
Electrical Downtilt Range 0-10° 0-12° 0-12°
Intra Band Isolation > 28 dB> 27 dB from 0° to 2° tilt
> 30 dB> 28 dB from 0° to 2° tilt
> 30 dB> 28 dB from 0° to 2° tilt
Isolation Between Bands 45 dB Typical 45 dB Typical 45 dB Typical
Isolation Between Left & Right Arrays > 28 dB (900 Band)> 27 dB (800 Band) > 30 dB > 30 dB
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical 18 dB Typical
Front-to-Back Ratio > 25 dB > 25 dB > 30 dB
Maximum Power (Per Port) 200 W 160 W 160 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
OPTIMAL PROFILE - LOW WINDLOAD
28 | April 2015
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2683 x 432 x 153 mm
Weight (Excluding Mounting Accessories) 48 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load(EN1991-4-1)
at 150 km/h Frontal: 990 N Lateral: 555 N Rear: 920 N Highest value: 1450 N at 110°
at 160 km/h Frontal: 1130 N Lateral: 630 N Rear: 1045 N Highest value: 1650 N at 110°
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
(2x) 790-960 / 1710-2170 / 2500-2690 MHz
5982200 lv (lightweight version)5982200A lv 5982200G lv 5982200DG lv
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.3 / 17.6 dBi | Variable Tilt
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
2683
432
153
1865
Location of the MDCU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 790-960 MHz
GREEN 790-960 MHz
BLUE 1710-2170 MHz
YELLOW 2500-2690 MHz
Packaging
Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 59 kg Includes 0900181/00 Kit
April 2015 | 29
(2x) 790-960 / 1710-2170 / 1710-2170 MHz
59802005980200A 5980200G 5980200DG
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
• Twin tri band antenna, dual polarisation, 12 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°
• MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
Ordering Options Model Number
Manual Electrical Tilt 5980200
Remote Electrical Tilt AISG1.1 5980200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5980200G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22) 5980200DG
Access Ports Description (Connectors)
This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded connectors located at the bottom face. See image on the following page.
RED and GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck
WHITE Rings High Band (Top Array) 1710-2170 MHz Ports (Wide Band) (4x) 7/16-DIN Female Long Neck
BLUE Rings High Band (Bottom Array) 1710-2170 MHz Ports(Wide Band Optimised for UMTS) (4x) 7/16-DIN Female Long Neck
Electrical Characteristics Low Band (RED or GREEN) High Band (WHITE) High Band (BLUE)
Frequency Bands (MHz) 790...880 880...960 1710...1880 1900...2170 1710...1880 1900...2170
Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value
17.2 17.5 16.5...16.716.3...16.516.0...16.3
16.7...17.216.5...17.016.3...16.5
16.5...16.916.4...16.716.3...16.5
16.9...17.316.7...17.216.5...17.0
Input Impedance 50Ω 50Ω 50Ω
VSWR < 1.5 < 1.4 < 1.4
Polarisation ±45° ±45° ±45°
Horizontal Beamwidth (-3 dB) 75° 68° 65° 62° 65° 62°
Vertical Beamwidth (-3 dB) 7° 7° 7° 7° 7°
Electrical Downtilt Range 0-10° 0-12° 0-12°
Intra Band Isolation > 30 dB> 28 dB from 0° to 2° tilt
> 30 dB> 28 dB from 0° to 2° tilt
> 30 dB> 28 dB from 0° to 2° tilt
Isolation Between Bands 45 dB Typical 45 dB Typical 45 dB Typical
Isolation Between Left & Right Arrays > 29 dB > 30 dB > 30 dB
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical 18 dB Typical
Front-to-Back Ratio > 30 dB > 30 dB > 30 dB
Maximum Power (Per Port) 200 W 160 W 160 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
LTE 800 Ready
30 | April 2015
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2700 x 442 x 152 mm (219 mm with Rear Connectors)
Weight (Excluding Mounting Accessories) 56 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 160 km/h (EN1991-4-1) Frontal: 1512 N Lateral: 512 N Rear: 1418 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
(2x) 790-960 / 1710-2170 / 1710-2170 MHz
59802005980200A 5980200G 5980200DG
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
Packaging
Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 | 70 kg
RED 790-960 MHz
GREEN 790-960 MHz
WHITE 1710-2170 MHz
BLUE 1710-2170 MHz
April 2015 | 31
(2x) 790-960 / 1710-2170 / 1710-2170 MHz
5980200 lv (lightweight version)5980200A lv 5980200G lv 5980200DG lv
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
• Twin tri band antenna, dual polarisation, 12 connectors • Independent tilt on each band 0-10° / 0-12° / 0-12°• Lightweight TwinLine platform with multi-array capability • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)
Ordering Options Model Number
Manual Electrical Tilt 5980200 lv
Remote Electrical Tilt AISG1.1 5980200A lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5980200G lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22) 5980200DG lv
Access Ports Description (Connectors)
This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded connectors located at the bottom face. See image on the following page.
RED and GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck
WHITE Rings High Band (Top Array) 1710-2170 MHz Ports (Wide Band) (4x) 7/16-DIN Female Long Neck
BLUE Rings High Band (Bottom Array) 1710-2170 MHz Ports(Wide Band Optimised for UMTS) (4x) 7/16-DIN Female Long Neck
Electrical Characteristics Low Band (RED or GREEN) High Band (WHITE) High Band (BLUE)
Frequency Bands (MHz) 790...880 880...960 1710...1880 1900...2170 1710...1880 1900...2170
Gain (dBi)Tilt 0°Tilt Mid ValueTilt Max Value
17.2 17.5 16.5...16.716.3...16.516.0...16.3
16.7...17.216.5...17.016.3...16.5
16.5...16.916.4...16.716.3...16.5
16.9...17.316.7...17.216.5...17.0
Input Impedance 50Ω 50Ω 50Ω
VSWR < 1.5 < 1.4 < 1.4
Polarisation ±45° ±45° ±45°
Horizontal Beamwidth (-3 dB) 75° 68° 65° 62° 65° 62°
Vertical Beamwidth (-3 dB) 7° 7° 7° 7° 7°
Electrical Downtilt Range 0-10° 0-12° 0-12°
Intra Band Isolation > 30 dB> 28 dB from 0° to 2° tilt
> 30 dB> 28 dB from 0° to 2° tilt
> 30 dB> 28 dB from 0° to 2° tilt
Isolation Between Bands 45 dB Typical 45 dB Typical 45 dB Typical
Isolation Between Left & Right Arrays > 29 dB > 30 dB > 30 dB
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical 18 dB Typical
Front-to-Back Ratio > 30 dB > 30 dB > 30 dB
Maximum Power (Per Port) 200 W 160 W 160 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
OPTIMAL PROFILE - LOW WINDLOAD
32 | April 2015
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2683 x 432 x 153 mm
Weight (Excluding Mounting Accessories) 48 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load(EN1991-4-1)
at 150 km/h Frontal: 990 N Lateral: 555 N Rear: 920 N Highest value: 1450 N at 110°
at 160 km/h Frontal: 1130 N Lateral: 630 N Rear: 1045 N Highest value: 1650 N at 110°
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
(2x) 790-960 / 1710-2170 / 1710-2170 MHz
5980200 lv (lightweight version)5980200A lv 5980200G lv 5980200DG lv
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
2683
432
153
1865
Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 790-960 MHz
GREEN 790-960 MHz
WHITE 1710-2170 MHz
BLUE 1710-2170 MHz
Packaging
Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 59 kg Includes 0900181/00 Kit
April 2015 | 33
(2x) 698-960 / 1695-2690 MHz
59613005961300A 5961300G 5961300DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.5 dBi | Variable Tilt
• Twin dual band antenna, dual polarisation, 8 connectors • Independent tilt on each band 0-10° / 0-10°• Lightweight TwinLine platform and low windload • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)
OPTIMAL PROFILE - LOW WINDLOADOrdering Options Model Number
Manual Electrical Tilt 5961300
Remote Electrical Tilt AISG1.1 5961300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5961300G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5961300DG
Access Ports Description (Connectors)
This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded connectors located at the bottom face. See image on the following page.
Ultra Low Band 698-960 MHz Ports (4x) 7/16-DIN Female Long Neck
Ultra Wide Band 1695-2690 MHz Ports (4x) 7/16-DIN Female Long Neck
Electrical Characteristics R1-R2 Y1-Y2
Frequency Bands (MHz) 700 800 900 1800 2100 2600
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
15.515.515.2
16.516.416.2
17.417.317.0
17.717.717.7
18.118.118.0
18.518.518.2
Input Impedance 50Ω 50Ω
VSWR < 1.5 < 1.5
Polarisation ±45° ±45°
Horizontal Beamwidth (-3 dB) 75° 68° 65° 65° 63° 61°
Vertical Beamwidth (-3 dB) 8.6° 7.5° 6.7° 6.1° 5.3° 4.2°
Electrical Downtilt Range 0-10° 0-10°
Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical
Front-to-Back Ratio
@ 180°@ 180° ±30°
> 30 dB> 25 dB
> 30 dB> 25 dB
Maximum Power (Per Port) 250 W 200 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
R1 R2
Y1 Y2
34 | April 2015
(2x) 698-960 / 1695-2690 MHz
59613005961300A 5961300G 5961300DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.5 dBi | Variable Tilt
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2683 x 432 x 153 mm
Weight (Excluding Mounting Accessories) 44 kg
Shroud Outdoor Fibreglass, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 150 km/h Frontal: 990 N Lateral: 555 N Rear: 920 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
Packaging
Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 55 kg Includes 0900181/00 Kit
RED 698-960 MHz
YELLOW 1695-2690 MHz
April 2015 | 35
(2x) 790-960 / 1710-2170 MHz
59612005961200A 5961200G 5961200DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.6 dBi | Variable Tilt
• Twin dual band Antenna, dual polarisation, 8 connectors • Independent tilt on each band 0-10° / 0-10°
• MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
Ordering Options Model Number
Manual Electrical Tilt 5961200
Remote Electrical Tilt AISG1.1 5961200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5961200G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G10G12) 5961200DG
Access Ports Description (Connectors)
This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded connectors located at the bottom face. See image on the following page.
RED | GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck
WHITE | BLUE Rings High Band 1710-2170 MHz Ports (Wide Band) (4x) 7/16-DIN Female Long Neck
Electrical Characteristics Low Band (RED or GREEN) High Band (WHITE or BLUE)
Frequency Bands (MHz) 790...880...960 MHz 1710...1880 1900...2170
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4
17.8...18.217.7...18.017.6...17.8
18.2...18.618.0...18.517.8...18.3
Input Impedance 50Ω 50Ω
VSWR < 1.5 < 1.5
Polarisation ±45° ±45°
Horizontal Beamwidth (-3 dB) 75°...68°...63° 65° 62°
Vertical Beamwidth (-3 dB) 7.0° 5.5° 5.0°
Electrical Downtilt Range 0-10° 0-10°
Intra Band Isolation > 28 dB > 30 dB, > 28 dB from 0° to 2° tilt
Isolation Between Bands 45 dB Typical 45 dB Typical
Isolation Between Left & Right Arrays > 25 dB for 790-880 MHz> 28 dB for 880-960 MHz > 30 dB
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical
Front-to-Back Ratio > 30 dB > 30 dB
Maximum Power (Per Port) 200 W 160 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
LTE 800 Ready
36 | April 2015
(2x) 790-960 / 1710-2170 MHz
59612005961200A 5961200G 5961200DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.6 dBi | Variable Tilt
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2700 x 442 x 152 mm
Weight (Excluding Mounting Accessories) 52 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 160 km/h (EN1991-4-1) Frontal: 1512 N Lateral: 512 N Rear: 1418 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
Packaging
Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 | 67 kg
RED 790-960 MHz
GREEN 790-960 MHz
BLUE 1710-2170 MHz
WHITE 1710-2170 MHz
April 2015 | 37
(2x) 790-960 / 1710-2170 MHz
5961200 lv (lightweight version)5961200A lv 5961200G lv 5961200DG lv
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.6 dBi | Variable Tilt
• Twin dual band antenna, dual polarisation, 8 connectors • Independent tilt on each band 0-10° / 0-10°• Lightweight TwinLine platform with multi-array capability • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)
Ordering Options Model Number
Manual Electrical Tilt 5961200 lv
Remote Electrical Tilt AISG1.1 5961200A lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5961200G lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G10G12) 5961200DG lv
Access Ports Description (Connectors)
This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded connectors located at the bottom face. See image on the following page.
RED | GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck
WHITE | BLUE Rings High Band 1710-2170 MHz Ports (4x) 7/16-DIN Female Long Neck
Electrical Characteristics Low Band (RED or GREEN) High Band (WHITE or BLUE)
Frequency Bands (MHz) 790...880...960 MHz 1710...1880 1900...2170
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4
17.8...18.217.7...18.017.6...17.8
18.2...18.618.0...18.517.8...18.3
Input Impedance 50Ω 50Ω
VSWR < 1.5 < 1.5
Polarisation ±45° ±45°
Horizontal Beamwidth (-3 dB) 75°...68°...63° 65° 62°
Vertical Beamwidth (-3 dB) 7.0° 5.5° 5.0°
Electrical Downtilt Range 0-10° 0-10°
Intra Band Isolation > 28 dB > 30 dB, > 28 dB from 0° to 2° tilt
Isolation Between Bands 45 dB Typical 45 dB Typical
Isolation Between Left & Right Arrays > 25 dB for 790-880 MHz> 28 dB for 880-960 MHz > 30 dB
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical
Front-to-Back Ratio > 30 dB > 30 dB
Maximum Power (Per Port) 200 W 160 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
LTE 800 Ready
38 | April 2015
(2x) 790-960 / 1710-2170 MHz
5961200 lv (lightweight version)5961200A lv 5961200G lv 5961200DG lv
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 17.5 / 18.6 dBi | Variable Tilt
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
2683
432
153
1865
Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2683 x 432 x 153 mm
Weight (Excluding Mounting Accessories) 44 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load(EN1991-4-1)
at 150 km/h Frontal: 990 N Lateral: 555 N Rear: 920 N Highest value: 1450 N at 110°
at 160 km/h Frontal: 1130 N Lateral: 630 N Rear: 1045 N Highest value: 1650 N at 110°
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
Packaging
Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 | 59 kg
RED 790-960 MHz
GREEN 790-960 MHz
BLUE 1710-2170 MHz
WHITE 1710-2170 MHz
April 2015 | 39
(2x) 698-960 MHz
59203005920300A 5920300G 5920300DG
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt
• Twin low band, dual polarisation, 4 connectors • Independent tilt on each band 0-10°• Lightweight TwinLine platform and low windload • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Ordering Options Model Number
Manual Electrical Tilt 5920300
Remote Electrical Tilt AISG1.1 5920300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5920300G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5920300DG
Access Ports Description (Connectors)
This antenna is built with two identical Low Band Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.
Ultra Low Band 698-960 MHz Ports (4x) 7/16-DIN Female Long Neck
Electrical Characteristics R1-R2
Frequency Bands (MHz) 700 800 900
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
15.515.515.2
16.516.416.2
17.417.317.0
Input Impedance 50Ω
VSWR < 1.5
Polarisation ±45°
Horizontal Beamwidth (-3 dB) 75° 68° 65°
Vertical Beamwidth (-3 dB) 8.6° 7.5° 6.7°
Electrical Downtilt Range 0-10°
Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical
Front-to-Back Ratio
@ 180°@ 180° ±30°
> 30 dB> 25 dB
Maximum Power (Per Port) 250 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
R1 R2
OPTIMAL PROFILE - LOW WINDLOAD
40 | April 2015
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2863 x 432 x 153 mm
Weight (Excluding Mounting Accessories) 35 kg
Shroud Outdoor Fibreglass, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 150 km/h Frontal: 990 N Lateral: 555 N Rear: 920 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
(2x) 698-960 MHz
59203005920300A 5920300G 5920300DG
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt
Packaging
Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 66 kg Includes 0900181/00 Kit
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 698-960 MHz
April 2015 | 41
(2x) 790-960 MHz
59202005920200A 5920200G
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt
• Twin 900 MHz antenna, dual polarisation, 4 connectors • Independent tilt on each band 0-10°
• MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Single RET module to control both tilt angles, fully inserted inside the antenna (field replaceable)
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Ordering Options Model Number
Manual Electrical Tilt 5920200
Remote Electrical Tilt AISG1.1 5920200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5920200G
Access Ports Description (Connectors)
This antenna is built with two identical 900 MHz Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.
RED Rings Ultra Low Band Right 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck
GREEN Rings Ultra Low Band Left 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck
Electrical Characteristics RED or GREEN Ports
Frequency Bands (MHz) 790...880...960 MHz
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4
Input Impedance 50Ω
VSWR < 1.4
Polarisation ±45°
Horizontal Beamwidth (-3 dB) 65° (±6°)
Vertical Beamwidth (-3 dB) 7.3°
Electrical Downtilt Range 0-10°
Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt
Isolation Between Left & Right Arrays > 30 dB
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical
Null Fill (First Null Below Main Beam) < 20 dB
Front-to-Back Ratio > 30 dB
Maximum Power (Per Port) 200 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET Module Part Number(one per antenna)
MDCU-A0000 for AISG1.1 protocol (one unit included in 5920200A)
MDCU-G0000 for 3GPP/AISG2.0 protocol (one unit included in 5920200G)
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
LTE Ready
42 | April 2015
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2700 x 442 x 152 mm
Weight (Excluding Mounting Accessories) 45 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 160 km/h Frontal: 1300 N Lateral: 220 N Rear: 1700 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets Not available ---
(2x) 790-960 MHz
59202005920200A 5920200G
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 790-960 MHz
GREEN 790-960 MHz
April 2015 | 43
(2x) 790-960 MHz
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Ordering Options Model Number
Manual Electrical Tilt 5920200 lv
Remote Electrical Tilt AISG1.1 5920200A lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5920200G lv
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22) 5920200DG lv
Access Ports Description (Connectors)
This antenna is built with two identical Extended Low Band Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.
RED Rings Extended Low Band 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck
GREEN Rings Extended Low Band 790-960 MHz Ports (2x) 7/16-DIN Female Long Neck
Electrical Characteristics Low Band (RED or GREEN Ports)
Frequency Bands (MHz) 790...880...960 MHz
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
16.5...17.0...17.516.5...17.0...17.516.4...16.9...17.4
Input Impedance 50Ω
VSWR < 1.5
Polarisation ±45°
Horizontal Beamwidth (-3 dB) 73°...68°...63°
Vertical Beamwidth (-3 dB) 7.3°
Electrical Downtilt Range 0-10°
Inter/Intra Band Isolation > 28 dB
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical
Front-to-Back Ratio > 30 dB
Maximum Power (Per Port) 200 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
LTE Ready
EXTREMELY PROFILED - LOW WINDLOAD
• Twin 800-900 antenna, dual polarisation, 4 connectors • Independent tilt on each band 0-10°• Lightweight TwinLine platform • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)
5920200 lv (lightweight version)5920200A lv 5920200G lv 5920200DG lv
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt
44 | April 2015
(2x) 790-960 MHz
5920200 lv (lightweight version)5920200A lv 5920200G lv 5920200DG lv
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 17.5 dBi | Variable Tilt
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
153
432
1865 1983
Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
Mechanical Characteristics
Dimensions (Height x Width x Depth) 2683 x 432 x 153 mm
Weight (Excluding Mounting Accessories) 37 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 150 km/h (EN1991-4-1) Frontal: 990 N Lateral: 555 N Rear: 920 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
Packaging
Carton Box 2.93 x 0.55 x 0.28 m 0.45 m3 51 kg Includes 0900181/00 Kit
RED 790-960 MHz
GREEN 790-960 MHz
April 2015 | 45
(2x) 698-960 / 1695-2180 / 2490-2690 MHz
59786005978600A 5978600G 5978600DG
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 16.5 / 17.5 / 18.0 dBi | Variable Tilt
• Twin tri band antenna, dual polarisation, 12 connectors • Independent tilt on each band 0-10° / 0-10° / 0-10°• Lightweight TwinLine platform and low windload • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)
OPTIMAL PROFILE - LOW WINDLOADOrdering Options Model Number
Manual Electrical Tilt 5978600
Remote Electrical Tilt AISG1.1 5978600A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5978600G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5978600DG
Access Ports Description (Connectors)
This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded connectors located at the bottom face. See image on the following page.
Ultra Low Band 698-960 MHz Ports (4x) 7/16-DIN Female Long Neck
Wide Band 1695-2180 MHz Ports (4x) 7/16-DIN Female Long Neck
LTE 2600 2490-2690 MHz Ports (4x) 7/16-DIN Female Long Neck
Electrical Characteristics R1-R2 B1-B2 Y1-Y2
Frequency Bands (MHz) 700 800 900 1800 2100 2600
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
14.514.514.2
15.515.415.1
16.416.316.0
17.417.417.4
17.717.717.6
18.018.017.7
Input Impedance 50Ω 50Ω 50Ω
VSWR < 1.5 < 1.5 < 1.5
Polarisation ±45° ±45° ±45°
Horizontal Beamwidth (-3 dB) 75° 68° 65° 65° 63° 61°
Vertical Beamwidth (-3 dB) 12° 10° 9.4° 6.1° 5.3° 4.2°
Electrical Downtilt Range 0-10° 0-10° 0-10°
Inter/Intra Band Isolation > 30 dB> 28 dB from 0° to 2° tilt
> 30 dB> 28 dB from 0° to 2° tilt
> 30 dB> 28 dB from 0° to 2° tilt
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical 18 dB Typical
Front-to-Back Ratio
@ 180°@ 180° ±30°
> 30 dB> 25 dB
> 30 dB> 25 dB
> 30 dB> 25 dB
Maximum Power (Per Port) 250 W 200 W 200 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
R1 R2
Y1 Y2
B1 B2
46 | April 2015
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
Mechanical Characteristics
Dimensions (Height x Width x Depth) 1915 x 432 x 153 mm
Weight (Excluding Mounting Accessories) 40 kg
Shroud Outdoor Fibreglass, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 150 km/h Frontal: 635 N Lateral: 395 N Rear: 656 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
(2x) 698-960 / 1695-2180 / 2490-2690 MHz
59786005978600A 5978600G 5978600DG
Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65° / 65° / 65° | 16.5 / 17.5 / 18.0 dBi | Variable Tilt
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
Packaging
Carton Box 2.15 x 0.55 x 0.28 m 0.33 m3 50 kg Includes 0900181/00 Kit
RED 698-960 MHz
BLUE 1695-2180 MHz
YELLOW 2490-2690 MHz
April 2015 | 47
(2x) 698-960 / 1695-2690 MHz
59633005963300A 5963300G 5963300DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 16.5 / 18.5 dBi | Variable Tilt
• Twin dual band antenna, dual polarisation, 8 connectors • Independent tilt on each band 0-10° / 0-10°• Lightweight TwinLine platform and low windload • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)
OPTIMAL PROFILE - LOW WINDLOADOrdering Options Model Number
Manual Electrical Tilt 5963300
Remote Electrical Tilt AISG1.1 5963300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5963300G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5963300DG
Access Ports Description (Connectors)
This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded connectors located at the bottom face. See image on the following page.
Ultra Low Band 698-960 MHz Ports (4x) 7/16-DIN Female Long Neck
Ultra Wide Band 1695-2690 MHz Ports (4x) 7/16-DIN Female Long Neck
Electrical Characteristics R1-R2 Y1-Y2
Frequency Bands (MHz) 700 800 900 1800 2100 2600
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
14.514.514.2
15.515.415.1
16.416.316.0
17.717.717.7
18.118.118.0
18.518.518.2
Input Impedance 50Ω 50Ω
VSWR < 1.5 < 1.5
Polarisation ±45° ±45°
Horizontal Beamwidth (-3 dB) 75° 68° 65° 65° 63° 61°
Vertical Beamwidth (-3 dB) 12° 10° 9.4° 6.1° 5.3° 4.2°
Electrical Downtilt Range 0-10° 0-10°
Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt > 30 dB, > 28 dB from 0° to 2° tilt
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical
Front-to-Back Ratio
@ 180°@ 180° ±30°
> 30 dB> 25 dB
> 30 dB> 25 dB
Maximum Power (Per Port) 250 W 200 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
R1 R2
Y1 Y2
48 | April 2015
(2x) 698-960 / 1695-2690 MHz
59633005963300A 5963300G 5963300DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65° / 65° | 16.5 / 18.5 dBi | Variable Tilt
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
Mechanical Characteristics
Dimensions (Height x Width x Depth) 1915 x 432 x 153 mm
Weight (Excluding Mounting Accessories) 33 kg
Shroud Outdoor Fibreglass, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 150 km/h Frontal: 635 N Lateral: 395 N Rear: 656 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
Packaging
Carton Box 2.15 x 0.55 x 0.28 m 0.33 m3 43 kg Includes 0900181/00 Kit
RED 698-960 MHz
YELLOW 1695-2690 MHz
April 2015 | 49
(2x) 790-960 / 1710-2170 MHz
59632005963200A 5963200G 5963200DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 68° / 68° | 16.5 / 18.1 dBi | Variable Tilt
• Twin dual band antenna, dual polarisation, 8 connectors • Independent tilt on each band 0-10° / 0-10° • TwinLine platform with multi-array capability • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies
Ordering Options Model Number
Manual Electrical Tilt 5963200
Remote Electrical Tilt AISG1.1 5963200A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5963200G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G10G12) 5963200DG
Access Ports Description (Connectors)
This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded connectors located at the bottom face. See image on the following page.
RED | GREEN Rings Low Band 790-960 MHz Ports (4x) 7/16-DIN Female Long Neck
WHITE | BLUE Rings High Band 1710-2170 MHz Ports (4x) 7/16-DIN Female Long Neck
Electrical Characteristics Low Band (RED or GREEN) High Band (WHITE or BLUE)
Frequency Bands (MHz) 790...880...960 MHz 1710...1880 1900...2170
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
15.5...16.0...16.515.5...16.0...16.515.4...15.9...16.4
17.3...17.617.2...17.417.2...17.3
17.6...18.117.4...17.917.3...17.7
Input Impedance 50Ω 50Ω
VSWR < 1.5 < 1.5
Polarisation ±45° ±45°
Horizontal Beamwidth (-3 dB) 72°...68°...65° 65° 64°
Vertical Beamwidth (-3 dB) 9° 6° 6°
Electrical Downtilt Range 0-10° 0-10°
Intra Band Isolation > 25 dB > 28 dB
Isolation Between Bands > 30 dB > 30 dB
Isolation Between Left & Right Arrays > 30 dB > 30 dB
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical 18 dB Typical
Front-to-Back Ratio > 30 dB > 30 dB
Maximum Power (Per Port) 200 W 160 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm < -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
50 | April 2015
(2x) 790-960 / 1710-2170 MHz
59632005963200A 5963200G 5963200DG
Twin Dual Band | Panel Antenna | (2x) XX-Pol | 68° / 68° | 16.5 / 18.1 dBi | Variable Tilt
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
Mechanical Characteristics
Dimensions (Height x Width x Depth) 1920 x 442 x 152 mm
Weight (Excluding Mounting Accessories) 41.5 kg
Shroud Outdoor Plastic, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load (EN1991-4-1)
at 150 km/h Frontal: 945 N Lateral: 320 N Rear: 886 N
at 160 km/h Frontal: 1075 N Lateral: 365 N Rear: 1008 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
Packaging
Carton Box 2.23 x 0.55 x 0.28 m 0.343 m3 | 52 kg
RED 790-960 MHz
GREEN 790-960 MHz
BLUE 1710-2170 MHz
WHITE 1710-2170 MHz
April 2015 | 51
(2x) 698-960 MHz
59183005918300A 5918300G 5918300DG
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 16.5 dBi | Variable Tilt
• Twin low band, dual polarisation, 4 connectors • Independent tilt on each band 0-10°• Lightweight TwinLine platform and low windload • MET and RET versions, AISG1.1 or 3GPP/AISG2.0 • Fully internal RET control based on our patented technologies (field replaceable)
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Ordering Options Model Number
Manual Electrical Tilt 5918300
Remote Electrical Tilt AISG1.1 5918300A
Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator 5918300G
Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator 5918300DG
Access Ports Description (Connectors)
This antenna is built with two identical Low Band Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded connectors located at the bottom face. See image on the following page.
Ultra Low Band 698-960 MHz Ports (4x) 7/16-DIN Female Long Neck
Electrical Characteristics R1-R2
Frequency Bands (MHz) 700 800 900
Gain (dBi)Tilt 0°Tilt 5°Tilt 10°
14.514.514.2
15.515.415.1
16.416.316.0
Input Impedance 50Ω
VSWR < 1.5
Polarisation ±45°
Horizontal Beamwidth (-3 dB) 75° 68° 65°
Vertical Beamwidth (-3 dB) 12° 10° 9.4°
Electrical Downtilt Range 0-10°
Inter/Intra Band Isolation > 30 dB, > 28 dB from 0° to 2° tilt
Upper Sidelobe Rejection(20° sector above main beam)
18 dB Typical
Front-to-Back Ratio
@ 180°@ 180° ±30°
> 30 dB> 25 dB
Maximum Power (Per Port) 250 W
Intermodulation3rd Order for 2x20W Carriers
< -110 dBm
Electrical Downtilt Control
Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET) Control
A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counter-clockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.
Remote Electrical Tilt (RET) Control
The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each band (no need for daisy chain cables between the bands). This module does not add any additional length to the antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain visible and the antenna still has manual tilt control (manual override).
RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
RET-Ready Actuator (one per antenna)
Multi-Device Control Unit (MCDU)
The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
Multi-Device Dual Unit (MDDU)
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.
Environmental
Operating Temperature Range -40° C to +60° C
Environmental ETS 300 019
RoHS Compliant Yes
R1 R2
OPTIMAL PROFILE - LOW WINDLOAD
52 | April 2015
Mechanical Characteristics
Dimensions (Height x Width x Depth) 1915 x 432 x 153 mm
Weight (Excluding Mounting Accessories) 24 kg
Shroud Outdoor Fibreglass, Grey RAL7035
Wind Speed Operational: 160 km/hr Survival: 200 km/h
Wind Load at 150 km/h Frontal: 635 N Lateral: 395 N Rear: 656 N
Mounting Kit Options Part Number Weight
All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
(2x) 698-960 MHz
59183005918300A 5918300G 5918300DG
Twin Band | Panel Antenna | (2x) X-Pol | 65° | 16.5 dBi | Variable Tilt
Packaging
Carton Box 2.15 x 0.55 x 0.28 m 0.33 m3 34 kg Includes 0900181/00 Kit
Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.
Location of the MDCU or MDDU for RET Control
Tilt indicators covered by transparent caps. Manual adjustment is accessed by removing the caps. Knob colours are the same as the connectors.
Bottom View of Antenna Dimensions (in mm)
In order to operate RET control, the transparent caps covering the tilt adjustment indicators must be engaged and locked. Do not cut them from the antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.
Installation
RED 698-960 MHz
April 2015 | 53