pannkoke flachglastechnik - device series 7xxx-ab · 2017. 6. 26. · compressed air-operated...
TRANSCRIPT
www.pannkoke.com
7011-AB 7000-ABs 7001-ABs
7000-AB 7001-AB2
7001-AB
7005-AB
7000-ABs
Device Series 7xxx-AB...
DB#_7xxx-ABx_GB.doc 29.04.2008 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
The 7xxx-AB unit series has been developed for glass storage areas. These vacuum lifting units can be used to move vertically stored plate material,
while keeping its surface stable.
The carrying pipe can be extended for this unit family, so that suction cup separation can be matched to the material being carried.
The modular construction of the unit means that its vacuum generation can always be matched to actual requirements.
Simple changing over of the vacuum unit means that a mains powered Kombi 7001-xx can be converted to a battery powered
Kombi 7011-xx. All units can be supplied with protection gratings and adjustable supports
for freshly sealed insulating glass units.
The units in version 2 of this series are able, during support of the lower edge of the transported plate, to lower it onto a surface, e.g. onto a table, or to
lift it from such a surface.
We also supply our unit range with twin circuit technology. Customized products pose no problem.
Take advantage of the experience we’ve gained in the production and application
of vacuum lifting units since 1965.
You can contact us at: Telephone: +49 451 / 47008-0 Fax: +49 451 / 47008-37 e-mail: [email protected] www.pannkoke.com
Groups of Devices
Vacuum Lifting Devices
VT_Info_09_Gerätegruppen_GB.doc 03.09.2008 1/4
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Type Description Description Group of Device
Frame Carrying Frames without Vacuum Generation
7000
Kombi Carrying Frames with
mains-operated, electrical vacuum pump
7001
Vacuum Unit mains-operated, electric Vacuum Unit
7002
Frame Carrying Frames with
hand-operated vacuum pump
7004
Venturi device Carrying Frames with
Compressed air-operated vacuum pump (venturi jet)
7005
Accu (Rechargeable Battery) Device Kombi
Carrying Frames with
mains-independent, electrical (battery-operated) vacuum pump
7011
Accu (Rechargeable Battery) Vacuum Unit
mains-independent, electric (rechargeable battery-operated) Vacuum Unit
7012
Manipulation device Carrying Frames with
mains-operated, electrical vacuum pump and
pneumatic drive
7021
Manipulation Device Carrying Frames with
compressed air-operated vacuum pump (venturi jet) and
pneumatic drive
7025
Kombi Carrying Frames with
mains-operated, electrical vacuum pump and
electrical drive
7031
Groups of Devices
Vacuum Lifting Devices
VT_Info_09_Gerätegruppen_GB.doc 03.09.2008 2/4
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Type Description Description Group of Device
Manipulation device Carrying Frames with
compressed air-operated vacuum pump and
electrical drive
7035
Manipulation device Carrying Frames with
mains-independent, electrical (battery-operated) vacuum pump and
pneumatic drive
7037
Kombi Carrying Frames with
mains-independent, electrical vacuum pump and
electrical drive
7041
Kombi Carrying Frame
with mains-operated, electrical vacuum pump
with 2-circuit-technique for the latest safety standard of the EC
7201
Vacuum Unit mains-operated, electric Vacuum Unit
with 2-circuit-technique for the latest safety standard of the EC
7202
Venturi device Carrying Frames with
Compressed air-operated vacuum pump (venturi jet)
with 2-circuit-technique for the latest safety standard of the EC
7205
Accu (Rechargeable Battery) Device Kombi
Carrying Frames with
mains-independent, electrical (battery-operated) vacuum pump
7211
Groups of Devices
Vacuum Lifting Devices
VT_Info_09_Gerätegruppen_GB.doc 03.09.2008 3/4
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Type Description Description Group of Device
with 2-circuit-technique for the latest safety standard of the EC
Accu (Rechargeable Battery) Vacuum Unit
mains-independent, electric (rechargeable battery-operated) Vacuum Unit
with 2-circuit-technique for the latest safety standard of the EC
7212
Manipulation Device Carrying Frames with
compressed air-operated vacuum pump (venturi jet) and
pneumatic drive
with 2-circuit-technique for the latest safety standard of the EC
7225
Kombi Carrying Frames with
mains-operated, electrical vacuum pump and
electrical drive
with 2-circuit-technique for the latest safety standard of the EC
7231
Kombi Carrying Frames with
mains-independent, electrical (battery-operated) vacuum pump and
electrical (battery-operated) drive
with 2-circuit-technique for the latest safety standard of the EC
7241
Accu (Rechargeable Battery) Device Kombi
Carrying Frames with
mains-independent, electrical (battery-operated) vacuum pump
with 4-circuit-technique for the latest safety standard of the EC
7411
Groups of Devices
Vacuum Lifting Devices
VT_Info_09_Gerätegruppen_GB.doc 03.09.2008 4/4
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Type Description Description Group of Device
Kombi Carrying Frames with
mains-independent, electrical (battery-operated) vacuum pump and
electrical (battery-operated) drive
with 4-circuit-technique for the latest safety standard of the EC
7441
VT_Info_03_Bewegung_GB.doc 30.04.2008 1/1
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Possibilities of the Transport Movements
Vertical
Horizontal
Turning
tilting vertical – horizontal horizontal - vertical
tilting only
vertical – horizontal
picking-up vertical – horizontal horizontal – vertical
only via the lower edge
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Table of Contents
Vacuum Lifting Devices Line 7xxx-AB
♦
♦
♦
♦
♦
♦
Which Device Groups are available?
Table of Contents
Device overview
A Comparison of the Device Groups
The Safety_Requirements of Vacuum Lifting Devices since 01.01.2004 within the EU
Questionnaire for the Selection of a Vacuum Lifting Device 7000-xx Frame Carrying Frame without vacuum generation
7000-AB SO01
7000-ABs 7000-AB 7002 Vacuum Unit mains-operated, electric vacuum pump 7002-Standard 7012 Accu Vacuum Unit battery-supplied, electric vacuum pump 7012-Handy 7012-HANDY2 7012-HANDY3
7202 Vacuum Unit mains-operated, electric vacuum pump 7202-HANDY2 (2KS)
7212 Accu Vacuum Unit battery-supplied, electric vacuum pump
7212-HANDY2 (2KS) 7212-HANDY3 (2KS) 7001-xx Kombi Carrying Frame with mains-operated, electric vacuum pump
7001-ABs 7001-AB
IV_01_Geräteübersicht_7xxx-AB_GB.doc 10.09.2008 1/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Table of Contents
Vacuum Lifting Devices Line 7xxx-AB
7201 Kombi Carrying Frame with mains operated, electric vacuum pump
7201-ABs (2KS) 7201-AB (2KS) 7011 Accu Device Kombi Carrying Frame with battery-supplied, electric vacuum pump
7011-ABs 7011-AB
7211 Accu Device Kombi Carrying Frame with battery-supplied, electric vacuum pump
7211-ABs (2KS) 7211-AB (2KS) 7005 Venturi Device Carrying Frame with compressed air-operated vacuum pump / venturi jet(s)
7005-AB 7005-AB/E
IV_01_Geräteübersicht_7xxx-AB_GB.doc 10.09.2008 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Overview
Vacuum Lifting Devices Line 7xxx-AB
Device Type No of
vacuum circuits
( )7000-AB 1 1 0 X X
7000-AB SO01 2 1 0 X
7000-ABs 1 1 0 X X
7001-AB 1 0 1 X X
7001-ABs 1 0 1 X X
7005-AB 1 1 0 X X
7005-AB/E 1 1 0 X X
7011-AB 1 0 1 X X
7011-ABs 1 0 1 X X
7201-AB 2 0 1 X X
7201-ABs 2 0 1 X X
7211-AB 2 0 1 X X
7211-ABs 2 0 1 X X
IV_03_Geräteübersicht_7xxx-AB_GB.doc 10.09.2008 1/1
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
#TB_Sicherheitsanforderung_GB.doc
Safety Requirements for Vacuum Lifting Devices
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Safety Requirements
VT_Info_15_Sicherheitsanforderungen_2004_GB.doc 30.04.2008 1/6
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Safety requirements for vacuum lifting devices taken from the European Standard EN 13155:2003 This draft for safety requirements of non-fixed load lifting attachments makes some essential requirements on a vacuum lifting device, which have to be fulfilled by each load suspension device and some only by vacuum lifting devices. Also, safety requirements for grabs and tongs are defined in this draft. The title of this standard is: Krane — Lose Lastaufnahmemittel Cranes — Non-fixed load lifting attachments Appareils de levage à charge suspendue — Equipements amovibles de prise de charge This standard is valid in all the EU countries. All new load lifting attachments brought into circulation since the 01.01.2004 must conform to this standard, this, at least, is our understanding. The forward to this standard contains the following:
This document (EN 13155:2003) has been prepared by Technical Committee CEN/TC 147 “Cranes - Safety”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2004, and conflicting national standards shall be withdrawn at the latest by January 2004.
This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s).
To determine the relationship to the EC Directive, see the information in Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and the United Kingdom.
Section 5 lists safety requirements and or measures. Particular requirements relating to vacuum lifting devices are given under point 5.2.2 of the standard.
Safety Requirements
VT_Info_15_Sicherheitsanforderungen_2004_GB.doc 30.04.2008 2/6
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Requirements Solutions at Pannkoke
5.2.2.1 Vacuum lifters shall be dimensioned to hold at least a load corresponding to two times the working load limit at the end of the working range and the beginning of the danger range respectively at all intended angles of tilt. The maximum angles of tilt shall be increased in accordance with 5.1.1.2.
NOTE: The pressure range within which it is possible to work is termed the working range. The danger range adjoins the working range. In some vacuum lifting systems, in particular self-priming vacuum lifters, the resultant pressure decrease depends upon the weight of the load.
The loading capacity of our built-in suction cups has a 2-fold safety factor at the minimum permissible depression.
The suction cups 388 were tested in the Fachhochschule Kiel with both a slide-off and a pull-off test. The suction cup 388 carrys 100 kg with a 2fold safety factor.
5.2.2.2 Non-self-priming vacuum lifters shall be equipped with a pressure measuring device clearly showing the working range and the danger range of the vacuum.
Our control vacuum meter has already been in use since the seventies and each of our vacuum lifting devices has such a control vacuum meter. The working range is marked green, the danger area red.
5.2.2.3 Self-priming vacuum lifters shall be equipped with an indicator showing to the operator that the end of the working range is reached.
This type of device is not manufactured by Pannkoke.
5.2.2.4 The measuring device or the indicator respectively shall be fully visible for the slinger or, if there is no slinger, for the driver of the crane when in his normal working position.
Each vacuum lifting device with built-in electric vacuum generation has a control vacuum meter, an acoustical and an optical warning signal which indicates a too low partial vacuum and this since the beginning of the eighties.
Rechargeable battery-operated vacuum lifting devices have been equipped since 2000 with two optical warning signals. Optionally we offer a large flash lamp as warning means and this is available for all electric operated devices with 2KS technology.
Compressed air powered vacuum lifting devices have had a control vacuum meter and an acoustic warning signal since 2004
5.2.2.5 Means shall be provided to prevent the risks due to vacuum losses. This shall be:
Safety Requirements
VT_Info_15_Sicherheitsanforderungen_2004_GB.doc 30.04.2008 3/6
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Requirements Solutions at Pannkoke
a) in the case of vacuum lifters with a vacuum pump: a vacuum reservoir with a non-return valve between the vacuum reservoir and the pump, located as close as possible to the vacuum reservoir
The carrying frame or parts of the carrying frame of our vacuum lifting devices are constructed in general as a vacuum tank. At the newer devices' type a will recognizable vacuum tank is used and it doesn't belong to the carrying parts. The tightness of the system is tested before delivery. Only devices which lose less than 5 % vacuum within 15 minutes will be delivered. With the rechargeable battery operated vacuum lifting devices there is also the fact that if the vacuum falls below a certain limit during use, the vacuum will be increased via the accumulator vacuum pump.
b) in the case of vacuum lifters with Venturi-systems: a pressure reservoir tank or vacuum reservoir tank with a non-return valve between the vacuum reservoir and the Venturi system, located as close as possible to the vacuum reservoir;
Only compressed air powered vacuum lifting devices with a closed vacuum system have been manufactured since 2000.
The carrying frame or parts of the carrying frame of our vacuum lifting devices are constructed in general as a vacuum tank. At the newer devices' type a will recognizable vacuum tank is used and it doesn't belong to the carrying parts.
The tightness of the system is tested before delivery. Only devices which lose less than 5 % vacuum within 15 minutes will be delivered.
c) in the case of turbine vacuum lifters: a supporting battery or an additional flywheel-mass;
This type of device is not manufactured by Pannkoke.
d) in the case of self-priming vacuum lifters: a reserve-stroke at least equal to 5 % of the total stroke of the piston..
NOTE: Vacuum losses can occur for example, due to leaks, or in the case of non self-priming vacuum lifters, due to a power failure.
This type of device is not manufactured by Pannkoke.
5.2.2.6 There shall be a device to warn automatically when the danger range is reached, if vacuum losses can not be compensated. The indication shall be optical and/or acoustic, depending upon the circumstances of use for the vacuum lifter, and in accordance with EN 981, EN 842 and EN 457; The warning device shall work even if there is a power supply failure to the vacuum lifter.
NOTE: The warning device is not the pressure measuring device of 5.2.2.2 or the indicator of 5.2.2.3.
Each vacuum lifting device with built-in electric vacuum generation has a control vacuum meter, an acoustical and an optical warning signal which indicates a too low partial vacuum and this since the beginning of the eighties.
Rechargeable battery-operated vacuum lifting devices have been equipped since 2000 with two optical warning signals. Optionally we offer a large flash lamp as warning means and this is available for all electric operated devices with 2KS technology.
Compressed air powered vacuum lifting devices have had a control vacuum meter and an acoustic warning signal since 2004
Safety Requirements
VT_Info_15_Sicherheitsanforderungen_2004_GB.doc 30.04.2008 4/6
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Requirements Solutions at Pannkoke
5.2.2.7 In case of power failure, the vacuum lifter shall be able to hold the load for 5 minutes. This is not necessary in no-go areas and this is not necessary for turbine vacuum lifters if all the following conditions are met:
• the operator maintains control of the load through steering handles which ensures that the operator is outside the danger zone in case of the load falling;
• in addition to clause 5.2.2.6 a warning device shall be activated as soon as the power fails;
• the manufacturer shall prohibit lifting of the geometric centre of the suction pads above 1.8 m by marking and instructions for use.
Since 2000, we have only manufactured vacuum lifting devices with one or more closed vacuum circuits (see 5.2.2.5).
The tightness of the system is tested before delivery. Only devices which lose less than 5 % vacuum within 15 minutes will be delivered.
5.2.3.8 For vacuum lifters intended to be used in a building area a secondary positive holding device is required or there shall be two vacuum reserves each fitted with non-return valves. Each vacuum reserve shall be connected to a separate set of suction pads.
Each set of suction pads shall fulfil the requirement of the clause 5.2.2.1.
All units in the 7201, 7211 or 7411 ranges have two independent vacuum circuits and are suitable for building site use.
The conversion to point 5.2.3.8 means that each vacuum circuit must be able to support the nominal load with 2-fold safety. This is only necessary for devices which are to be used on a building site. Each vacuum circuit requires the same monitoring functions as a device with only one vacuum circuit.
When using a single circuit vacuum lifting device on a building site, an additional locking-fit support device must be used, which must be able to support the nominal load by itself at all times with the required degree of safety in every position. For example, this can be resolved by using brackets or a load strap up until the time of use. All of these measures fail only in an actual dangerous activity and the operator is then hard pressed to explain how the working of his safety measure conforms to the standard, when an accident has already occurred.
5.2.2.9 The releasing of the load shall be actuated by a two action control. This is not necessary if the release of the load is not possible until the load has been put down or in no-go areas.
For electrical lifting devices this is achieved by using a mushroom button (such as an emergency-off switch). It has to be turned for changing. The mushroom-shaped key is in a housing with edge protection and with that the actuating element is protected by the surrounding mechanical protection.
A protective shield is built around the hand valve(s) to prevent an unintentional actuation.
Since 2004, compressed air powered devices have only been supplied with single-hand twofold actuation.
5.2.2.10 Controls for tilting or turning movements shall be hold-
Safety Requirements
VT_Info_15_Sicherheitsanforderungen_2004_GB.doc 30.04.2008 5/6
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Requirements Solutions at Pannkoke
to-run type.
5.2.2.11 The shape of the suction pad shall be matched to that of the intended load(s). If more than one suction pad is used in conjunction with a lifting beam, the layout and working load limit of the suction pads shall be matched to that of the intended load(s). The share of the load which can foreseeable be imposed on each suction pad shall not exceed its working load limit taking account of the rigidity of both the load and the vacuum lifter.
Under item 7 there are special requirements concerning user information. Under item 7.1.2.3 vacuum lifting devices there are special requirements concerning the user information. A) Checking of the vacuum level; B) Measures to be taken as soon as the warnings are actuated; C) Checking of the condition of the vacuum connections and hoses; D) Checking of the condition of the suction pads. Also the minimum marking is clearly described under point 7.2.1. This minimum marking has to be on a durable label: a) Identification of manufacturer (or authorized representative or importer); b) Type c) Serial number; d) Dead weight e) Year of construction f) Carrying capacity in kg g) CE-mark.
Safety Requirements
VT_Info_15_Sicherheitsanforderungen_2004_GB.doc 30.04.2008 6/6
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Requirements which go beyond the safety draft of the CEN/TC 151/WG 13/SG A1. This working group has the following title:
Machines and plants for the manufacture, treatment and processing of flat glass
- Safety requirements - Part 1: Storage, handling and transportation
equipment inside the factory
Requirements Solutions at Pannkoke
5.7.1.1 The vacuum shall have redundancy so that if part of the systems fails then the remaining part of it shall be capable of supporting the actual load.
For our new devices with 2-circuit-vacuum-system (2KS) this is the case for electric as well as for compressed-air operated vacuum lifting devices.
Systems shall be provided to control and monitor vacuum losses comprising:
a) In the case of vacuum lifters with a vacuum pump a reserve vacuum tank of minimum volume of at least twice the total evacuated volume of the system.
The carrying frame or parts of the carrying frame of our vacuum lifting devices are constructed in general as a vacuum tank. At the newer devices' type a will recognizable vacuum tank is used and it doesn't belong to the carrying parts. The tightness of the system is tested before delivery. Only devices which lose less than 5 % vacuum within 15 minutes will be delivered. With the rechargeable battery operated vacuum lifting devices there is also the fact that if the vacuum falls below a certain limit during use, the vacuum will be increased via the accumulator vacuum pump.
5.7.4
b) In the case of vacuum lifters with injector venturi, every injector shall be equipped with a non return valve.
Behind the venturi jet (injector) is a non-return valve and then a vacuum tank. At 2KS System is for each vacuum circuit a vacuum tank with non-return valve available.
5.7.5.1 For raw glass either guarding on the rear of the frame with handles or guide handles alone shall be fitted and arranged in a way which protects the operator from falling glass. No guarding is required for small plates (maximum dimension less than 2M), provided the distance from the sucker cup edge of the glass is less than the distance the guide handles are from he glass.
Is available optionally on request for the corresponding glass size.
5.7.5.2 It shall be possible to guide vacuum lifters using both hands, even if the operator has to simultaneously operate a hoist.
Is available optionally on request for the corresponding glass size.
#TB_Fragebogen_GB.doc
Questionnaire Vacuum Handling Technique
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Questionnaire: Vacuum Handling Technique
VT_01_Fragebogen_für_Vakuumhebegeräte_GB.doc 30.04.2008 1/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Company (company stamp)
Person in charge: _________________________ Phone: __________________________
E-mail: _________________________ Fax: __________________________
With our vacuum equipment devices you can lift, hold and transport many different materials such as glass, synthetics, concrete, sheets, plastic coated and gastight chip board, stone etc. The surface can be planed and in some cases curved or beaded. It is also possible to work with materials up to 330 degrees Celsius.
1. Material to be lifted: ___________________________________________________________
2. Condition of the surface gastight [ ] yes [ ] no Surface temperature: ____________ °C damp [ ] yes [ ] no dusty [ ] yes [ ] no Surface plane [ ] yes [ ] no radius: ____________________________ [ ] smooth [ ] rough [ ] _______________________________
3. Weight of the transport load: _____________________________________________________
4. Max. dimensions of the transport load (length x width x thickness): ________________________
5. Min. dimensions of the transport load (length x width x thickness): ________________________
6. How shall the transport load be moved? [ ] horizontal [ ] vertical [ ] horizontal and vertical
7. Which manipulating possibilites are preferred? [ ] tilting by 90° [ ] turning by 90° [ ] ______________________________________
8. How shall the manipulating movement be executed? [ ] manual [ ] electrical [ ] pneumatic [ ] ___________________
9. How is the transport load being stored? [ ] standing [ ] lying [ ] in a rack [ ] in a case [ ] ______________________________________
Questionnaire: Vacuum Handling Technique
VT_01_Fragebogen_für_Vakuumhebegeräte_GB.doc 30.04.2008 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
10. Where shall the transport load be transported? [ ] within the factory [ ] on the site [ ] open-air ground [ ] ______________________________________
11. Which load suspension device is available? [ ] craneway [ ] column crane [ ] mobile crane [ ] fork stacker [ ] ______________________________________
12. Which suspension will you prefer? [ ] steel cable sling [ ] suspension eye [ ] ______________________________________ crane hook for ______________ kg
13. Which power supply is available and/or requested? [ ] current voltage: __________ V frequency: __________ Hz phases: __________ [ ] Rechangeable battery-operation (possible to some extent) [ ] Compressed air ______________ bar
14. How shall the connection to the power supply be executed: hose winder, cable lap winder, length etc.? ______________________________________________________________________________
15. How shall the vacuum be generated? [ ] built-in vacuum pump [ ] external vacuum pump [ ] venturi jet [ ] ______________________________________
16. How long must the vacuum be held? _____________________________________
17. Should the device be dismountable (for transport and/or storage)? [ ] no [ ] yes how? _____________________________________
18. Do you need a remote control? [ ] no [ ] yes ( ) at the guide handle of the device ( ) in the hand --- how long? ____m
19. Should the suction cups be individually lockable? [ ] no [ ] yes
20. Is the surface easily soiled? [ ] insensitive [ ] the suction cups may not leave marks (non-abrasive)
Carrying Frames withou
#TB_7000_GB.doc
7000-xx t vacuum generation
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
#TB_vertikal_GB.doc 21.09.2006 1/1
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 e-Mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Possibilities of the Transport Movements
vertical
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
7000-AB_SO01_GB.doc 03.09.2008 subject to changes 1/2
Frame 7000-AB SO01
for vertical lifting and transporting the perfect device for the warehouse Description increased safety via 2 independent vacuum circuits acording to EN 13155 & prEN 13035-1 & prEN 13035-2 each vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter 2 completely closed vacuum circuits
prevent loss of vacuum at power failure warning lamp and acoustic signal indicate
insufficient vacuum single row arrangement of suction cups outer suction cups lockable vertical transport approx. 85° with two vacuum steps - low vacuum step for thin glass guide handles are adjustable in the height Vacuum Generation external vacuum generation necessary
e. g. via a Pannkoke Compound Pump 7002-COMP2 in the craneway
Control Means ON/OFF directly at the device SUCTION/RELEASE via a hand valve for each vacuum circuit Suspension: 2-fold crane string Safe Working Load: 1000 kg Colour: yellow
vertical
2-circuit vacuum lifting device according to
EN 13155
7000-AB_SO01_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-Mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups black rubber
abrasion possible up to 100° C heat resistant
number of suction cups 6 10 12 carrying bar length approx. mm 2200 3500 4000 safe working load on smooth and clean surface at 60 % vacuum kg
500
1000
1000
dead weight approx. kg 80 86 95 structural depth approx. mm 200 vacuum infeed connection 9 mm voltage 230 Volt 50/60 Hz 1 Ph Item No.: 7000-AB_SO01... 06-0910 10-0910 12-0910
#TB_ablegen_GB.doc 26.04.2008 1/1
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 e-Mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Possibilities of the Transport Movements
vertical
picking-up vertical – horizontal horizontal – vertical
only via the lower edge
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
7000-ABs_GB.doc 03.09.2008 subject to changes 1/2
Frame 7000-ABs
for vertical lifting and transporting the perfect device for the warehouse Description 1-circuit vacuum system control vacuum meter on the device single row arrangement of suction cups
with additional supporting suction cups suction cups fixed directly on the frame fixed suction cup spacing outer suction cups lockable modular device construction vertical transport approx. 85° guide handles are adjustable in the height Vacuum Generation external vacuum generation necessary
e. g. via a Pannkoke Compound Pump 7002-COMP2 in the craneway
Control Means SUCTION/RELEASE via hand valve at the device
or via remote control of the vacuum generation
Suspension: 2-fold crane string Safe Working Load: 1200 kg Colour: yellow / partly zinked The turnable suspension allows the picking-up/depositing of large sheets (horizontal to vertical/vertical to horizontal)
vertical
picking-up
For operation on EC construction sites only
permissible with mechanical holding device
according to EN 13155
7000-ABs_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups black rubber
abrasion possible up to 100° C heat resistant
number of suction cups 6 10 carrying bar length approx. mm 3000 3500 safe working load on smooth and clean surface at 60 % vacuum kg
500
1000
dead weight approx. kg 90 110 vacuum infeed connection 9 mm Item No.: 7000-ABs... 06-0910 10-0910 Special Design
on request
Accessories on request Item No.: 388-SCHUTZ protection cap for suction cup 388 Item No.: 7003-SchutzAB guard grating (size in accordance to your requirement) Item No.: 7003-UStAB support for just sealed units
(size in accordance to your requirement)
7000-AB_GB.doc 03.09.2008 subject to changes 1/2
Frame 7000-AB
for vertical lifting and transporting the perfect device for the warehouse Description 1-circuit vacuum system control vacuum meter on the device single row arrangement of suction cups
with additional supporting suction cups suction cups fixed directly on the frame outer suction cup distance adjustable via moving of the carrying
bars outer suction cups lockable modular device construction vertical transport approx. 85° guide handles are adjustable in the height Vacuum Generation external vacuum generation necessary
e. g. via a Pannkoke Compound Pump 7002-COMP2 in the craneway
Control Means SUCTION/RELEASE via hand valve at the device
or via remote control of the vacuum generation
Suspension: 2-fold crane string Safe Working Load: 1200 kg Colour: yellow / partly zinked The turnable suspension allows the picking-up/depositing of large sheets (horizontal to vertical/vertical to horizontal).
vertical
picking-up
For operation on EC construction sites only
permissible with mechanical holding device
according to EN 13155
7000-AB_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups black rubber
abrasion possible up to 100° C heat resistant
number of suction cups 6 10 carrying bar length minimum approx. mm maximum approx. mm
2200 3500
2900 3500
safe working load on smooth and clean surface at 60 % vacuum kg
500
1000
dead weight approx. kg 90 110 vacuum infeed connection 9 mm Item No.: 7000-AB... 06-0910 10-0910 Special Design
on request
Accessories on request Item No.: 388-SCHUTZ protection cap for suction cup 388 Item No.: 7003-SchutzAB guard grating (size in accordance to your requirement) Item No.: 7003-UStAB support for just sealed units
(size in accordance to your requirement)
mains-operated, e
battery-supplied, e
#TB_7002&7012_GB.doc
7002-xx lectric vacuum pump
7012-xx lectric vacuum pump
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
7002-Standard_GB.DOC 29.08.2008 subject to changes 1/2
Standard Pump 7002-Standard
Standard Pump for installation to machines, stacking devices etc. Description 1-circuit vacuum system the vacuum circuit has a 20 l vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter completely closed vacuum circuit
prevents loss of vacuum at power failure Vacuum Generation built-in low maintenance vacuum pump (dry running system) for mains supply Control Mean: ON/OFF SUCTION/RELEASE via hand valve at the device Installation vertically, horizontally or hanging possible Colour: yellow
7002-Standard_GB.DOC 29.08.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 e-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
assembly dimension length approx. mm 650 width approx. mm 220 height approx. mm 510 dead weight approx. kg
35
vacuum infeed connection 9 mm outout approx. 7.0 m³/h voltage 400 Volt 50/60 Hz 3 Ph Item No.: 7002-Standard
special voltage on request
7012-HANDY_GB.DOC 03.09.2008 subject to changes 1/2
Accu Vacuum Unit 7012-Handy
the vacuum generation for versatile application for frames from small to mid-sized Description 1-circuit vacuum system the vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter completely closed vacuum circuit
prevents loss of vacuum at power failure Vacuum Generation built-in low maintenance rechargeable battery vacuum pump
(dry running system) for rechargeable battery and line operation without change-over built-in accumulator charger for charging over night no change of rechargeable battery necessary no cable - no hose Control Means ON/OFF directly at the device SUCTION/RELEASE via hand valve at the device
optional via cable remote control optional via infrared remote control
Output: 1.5 m³/h Vacuum infeed connection: 9 mm Dead weight: approx. 27 kg Colour: yellow voltage charger for battery 230 Volt 50/60 Hz 1 Ph Item-no. 7012-HANDY voltage charger for battery 110 Volt 50/60 Hz 1 Ph Item-no. 7012-HANDY-110
7012-HANDY_GB.DOC 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Accessories on request Item No.: 7003-BK/DS cable remote control
SUCTION/RELEASE
Item No.: 7003-IR2S infrared remote control
SUCTION/RELEASE
Item No.: 7003-BK/DS infrared remote control
SUCTION/RELEASE only outside the EC
Hose Winder with 10 m hose 7003-T45A
Hose Winder with hose in special length 7003-T45AS
Connection Elements to the frame
Hose Spiral approx. 5 m 7003-SP6
7012-HANDY2_GB.doc 03.09.2008 subject to changes 1/2
Accu Vacuum Unit 7012-HANDY 2
the vacuum generation for versatile application for frames from small to mid-sized Description 1-circuit vacuum system the vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter completely closed vacuum circuit
prevents loss of vacuum at power failure Vacuum Generation built-in low maintenance rechargeable battery vacuum pump
(dry running system) for rechargeable battery and line operation without change-over built-in accumulator charger for charging over night no change of rechargeable battery necessary no cable - no hose Control Means ON/OFF directly at the device SUCTION/RELEASE via cable remote control
optional via infrared remote control
Output: 1.5 m³/h Vacuum infeed connection: 9 mm Dead weight: approx. 27 kg Colour: yellow voltage charger for battery 230 Volt 50/60 Hz 1 Ph Item-no. 7012-HANDY voltage charger for battery 110 Volt 50/60 Hz 1 Ph Item-no. 7012-HANDY-110
7012-HANDY2_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Accessories on request Item No.: 7003- DSFUS2 infrared remote control
SUCTION/RELEASE
Item No.: 7003-DSFUST infrared remote control
SUCTION/RELEASE only outside the EC
Hose Winder with 10 m hose 7003-T45A
Hose Winder with hose in special length 7003-T45AS
Connection Elements to the frame
Hose Spiral approx. 5 m 7003-SP6
7012-HANDY3_GB.DOC 03.09.2008 subject to changes 1/2
Accu Vacuum Unit 7012-HANDY 3
the vacuum generation for versatile application for frames from small to mid-sized Description 1-circuit vacuum system the vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter completely closed vacuum circuit
prevents loss of vacuum at power failure Vacuum Generation built-in low maintenance rechargeable battery vacuum pump
(dry running system) for rechargeable battery and line operation without change-over built-in accumulator charger for charging over night no change of rechargeable battery necessary no cable - no hose Control Means ON/OFF directly at the device SUCTION/RELEASE via hand valve at the device
optional via cable remote control optional via infrared remote control
Output: 1.5 m³/h Vacuum infeed connection: 9 mm Dead weight: Colour: yellow voltage charger for battery 230 Volt 50/60 Hz 1 Ph Best.-Nr. 7012-HANDY3 voltage charger for battery 110 Volt 50/60 Hz 1 Ph Best.-Nr. 7012-HANDY3-110
7012-HANDY3_GB.DOC 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Accessories on request Item No.: 7003-BK/DS cable remote control
SUCTION/RELEASE
Item No.: 7003-IR2S infrared remote control
SUCTION/RELEASE
Item No.: 7003-BK/DS infrared remote control
SUCTION/RELEASE only outside the EC
Hose Winder with 10 m hose 7003-T45A
Hose Winder with hose in special length 7003-T45AS
Connection Elements to the frame
Hose Spiral approx. 5 m 7003-SP6
mains-operated, e
battery-supplied, e
#TB_7202&7212_GB.doc
7202-xx lectric vacuum pump
7212-xx lectric vacuum pump
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
7202-HANDY2_GB.doc 03.09.2008 subject to changes 1/2
Vacuum Unit 7202-HANDY2
the vacuum generation for versatile application for frames from small to mid-sized Description 2-circuit vacuum system each vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter 2 completely closed vacuum circuits
prevent loss of vacuum at power failure interconnected operation possible up to 4 vacuum units Vacuum Generation built-in low maintenance vacuum pump (dry running system) for mains supply Control Means ON/OFF directly at the device SUCTION/RELEASE via cable remote control
optional via infrared remote control
Output: 3 m³/h Vacuum infeed connection: 9 mm Dead weight: approx. 27 kg Colour: yellow Voltage 400 Volt 50/60 Hz 3 Ph Item-no. 7202-HANDY2-400 Voltage 230 Volt 50/60 Hz 1 Ph Item-no. 7202-HANDY2-230 Voltage 110 Volt 50/60 Hz 1 Ph Item-no. 7202-HANDY2-110
2-circuit vacuum pump according to
EN 13155
7202-HANDY2_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Accessories on request Item No.: 7003- DSFUS2 infrared remote control
SUCTION/RELEASE
Item No.: 7003-DSFUST infrared remote control
SUCTION/RELEASE only outside the EC
Item No.: 7003-WL24 large warning lamp (flash
light for collecting failures)
7212-HANDY2_GB.doc 03.09.2008 subject to changes 1/2
Accu Vacuum Unit 7212-HANDY2
the vacuum generation for versatile application for frames from small to mid-sized Description 2-circuit vacuum system each vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter 2 completely closed vacuum circuits
prevent loss of vacuum at power failure interconnected operation possible up to 4 vacuum units Vacuum Generation built-in low maintenance rechargeable battery vacuum pump
(dry running system) for rechargeable battery and line operation without change-over built-in accumulator charger for charging over night no change of rechargeable battery necessary no cable - no hose Control Means ON/OFF directly at the device SUCTION/RELEASE via cable remote control
optional via infrared remote control
Output: 1.5 m³/h Vacuum infeed connection: 9 mm Dead weight: approx. 27 kg Colour: yellow voltage charger for battery 230 Volt 50/60 Hz 1 Ph Item-no. 7212-HANDY2 voltage charger for battery 110 Volt 50/60 Hz 1 Ph Item-no. 7212-HANDY2-110
2-circuit vacuum pump according to
EN 13155
7212-HANDY2_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Accessories on request Item No.: 7003- DSFUS2 infrared remote control
SUCTION/RELEASE
Item No.: 7003-DSFUST infrared remote control
SUCTION/RELEASE only outside the EC
Item No.: 7003- WL12 large warning lamp (flash
light for collecting failures)
7212-HANDY3_GB.doc 03.09.2008 subject to changes 1/2
Accu Vacuum Unit 7212-HANDY 3
the vacuum generation for versatile application for frames from small to mid-sized Description 2-circuit vacuum system each vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter 2 completely closed vacuum circuits
prevent loss of vacuum at power failure interconnected operation possible up to 4 vacuum units Vacuum Generation built-in low maintenance rechargeable battery vacuum pump
(dry running system) for rechargeable battery and line operation without change-over built-in accumulator charger for charging over night no change of rechargeable battery necessary no cable - no hose Control Means ON/OFF directly at the device SUCTION/RELEASE via hand valve at the device
optional via cable remote control or via infrared remote control
Output: 1.5 m³/h Vacuum infeed connection: 9 mm Dead weight: Colour: yellow voltage charger for battery 230 Volt 50/60 Hz 1 Ph Best.-Nr. 7212-HANDY3 voltage charger for battery 110 Volt 50/60 Hz 1 Ph Best.-Nr. 7212-HANDY3-110
2-circuit vacuum pump according to
EN 13155
7212-HANDY3_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Accessories on request Item No.: 7003- DSFUS2 infrared remote control
SUCTION/RELEASE
Item No.: 7003-DSFUST infrared remote control
SUCTION/RELEASE only outside the EC
Item No.: 7003- WL12 large warning lamp (flash
light for collecting failures)
mains-operated, e
#TB_7001_GB.doc
7001-xx Carrying Frames with lectric vacuum pump
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
#TB_ablegen_GB.doc 26.04.2008 1/1
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 e-Mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Possibilities of the Transport Movements
vertical
picking-up vertical – horizontal horizontal – vertical
only via the lower edge
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
7001-ABs_GB.doc 03.09.2008 subject to changes 1/2
Kombi 7001-ABs
for vertical lifting and transporting the perfect device for the warehouse Description 1-circuit vacuum system control vacuum meter on the device single row arrangement of suction cups
with additional supporting suction cups suction cups fixed directly on the frame fixed suction cup spacing outer suction cups lockable modular device construction vertical transport approx. 85° guide handles are adjustable in the height Vacuum Generation built-in low maintenance vacuum pump (dry running system) for mains supply Control Means ON/OFF directly at the device SUCTION/RELEASE via cable remote control Suspension: 2-fold crane string Safe Working Load: 1500 kg Colour: yellow The turnable suspension allows the picking-up/depositing of large sheets (horizontal to vertical/vertical to horizontal).
vertical
picking-up
For operation on EC construction sites only
permissible with mechanical holding device
according to EN 13155
7001-ABs_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups rubber black - abrasion possible - up to 100° C heat resistance number of suction cups 6 10 carrying bar length approx. mm 3000 3500 safe working load on smooth and clean surface at 60 % vacuum kg
500
1000
dead weight approx. kg 90 100 output 6.0 m³/h voltage 400 Volt 50 Hz 3 Ph Item No.: 7001-ABs... 6-0910-400 10-0910-400
output 3.0 m³/h voltage 230 Volt 50 Hz Item No.: 7001-ABs... 6-0910 10-0910
output 3.0 m³/h voltage 110 Volt 50 Hz Item No.: 7001-ABs... 6-0910-110 10-0910-110 Special Design and Special Voltage
on request
Accessories on request Item No.: 388-SCHUTZ protection cap for suction cup 388 Item No.: 7003-SchutzAB guard grating (size in accordance to your requirement) Item No.: 7003-UStAB support for just sealed units
(size in accordance to your requirement)
Also available as 2-circuit vacuum lifting device (Type 7201-ABs) in accordance to EN 13155 / prEN 13035.
7001-AB_GB.doc 03.09.2008 subject to changes 1/2
Kombi 7001-AB
for vertical lifting and transporting the perfect device for the warehouse Description 1-circuit vacuum system control vacuum meter on the device single row arrangement of suction cups
with additional supporting suction cups suction cups fixed directly on the frame outer suction cup distance adjustable via moving of the carrying
bars outer suction cups lockable modular device construction vertical transport approx. 85° guide handles are adjustable in the height Vacuum Generation built-in low maintenance vacuum pump (dry running system) for mains supply Control Means ON/OFF directly at the device SUCTION/RELEASE via cable remote control Suspension: 2-fold crane string Safe Working Load: 1500 kg Colour: yellow / partly zinked The turnable suspension allows the picking-up/depositing of large sheets (horizontal to vertical/vertical to horizontal).
vertical
picking-up
For operation on EC construction sites only
permissible with mechanical holding device
according to EN 13155
7001-AB_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups black rubber
abrasion possible up to 100° C heat resistant
number of suction cups 6 10 carrying bar length minimum approx. mm maximum approx. mm
2200 3500
2900 3500
safe working load on smooth and clean surface at 60 % vacuum kg
500
1000
dead weight approx. kg 90 100 vacuum infeed connection 9 mm output 6.0 m³/h voltage 400 Volt 50 Hz 3 Ph Item No.: 7001-AB... 06-0910-400 10-0910-400
output 3.0 m³/h voltage 230 Volt 50 Hz Item No.: 7001-AB... 6-0910 10-0910
output 3.0 m³/h voltage 110 Volt 50 Hz Item No.: 7001-AB... 6-0910-110 10-0910-110 Special Design and Special Voltage
on request
Accessories on request Item No.: 388-SCHUTZ protection cap for suction cup 388 Item No.: 7003-SchutzAB guard grating (size in accordance to your requirement) Item No.: 7003-UStAB support for just sealed units
(size in accordance to your requirement)
Also available as 2-circuit vacuum lifting device (Type 7201-AB) in accordance to EN 13155 / prEN 13035.
mains-operated, e
#TB_7201_GB.doc
7201-xx Carrying Frame with lectric vacuum pump
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
#TB_ablegen_GB.doc 26.04.2008 1/1
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 e-Mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Possibilities of the Transport Movements
vertical
picking-up vertical – horizontal horizontal – vertical
only via the lower edge
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
7201-ABs_GB.doc 03.09.2008 subject to changes 1/2
Kombi 7201-ABs
for vertical lifting and transporting the perfect device for the warehouse Description increased safety via 2 independent vacuum circuits
each vacuum circuit is designed with 2-fold safety acording to EN 13155 & prEN 13035-1 & prEN 13035-2 each vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter 2 completely closed vacuum circuits
prevent loss of vacuum at power failure warning lamp and acoustic signal indicate
insufficient vacuum power failure monitoring system single row arrangement of suction cups
with additional supporting suction cups suction cups fixed directly on the frame fixed suction cup spacing outer suction cups lockable modular device construction vertical transport approx. 85° guide handles are adjustable in the height Vacuum Generation built-in low maintenance vacuum pump (dry running system) for mains supply Control Means ON/OFF directly at the device SUCTION/RELEASE via cable remote control
optional via infrared remote control
Suspension: 2-fold crane string Safe Working Load: 1000 kg Colour: yellow The turnable suspension allows the picking-up/depositing of large sheets (horizontal to vertical/vertical to horizontal).
vertical
picking-up
2-circuit vacuum lifting device according to
EN 13155
7201-ABs_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups rubber black - abrasion possible - up to 100° C heat resistance number of suction cups 2 x 4 2 x 6 carrying bar length approx. mm 3000 3500 safe working load on smooth and clean surface at 60 % vacuum at EC construction sites kg in-plant kg
400 800
600 1000
dead weight approx. kg 90 100 structural depth approx. mm output 6.0 m³/h voltage 400 Volt 50 Hz 3 Ph Item No.: 7201-ABs... 8-0910-400 12-0910-400
output 3.0 m³/h voltage 230 Volt 50 Hz Item No.: 7201-ABs... 8-0910 12-0910
output 3.0 m³/h voltage 110 Volt 50 Hz Item No.: 7201-ABs... 8-0910-110 12-0910-110 Special Design and Special Voltage
on request
Accessories on request Item No.: 388-SCHUTZ protection cap for suction cup 388 Item No.: 7003- DSFUS2 infrared remote control SUCTION/RELEASE Item No.: 7003-DSFUST infrared remote control SUCTION/RELEASE
only outside the EC Item No.: 7003-WL large warning lamp (flash light for collecting failures) Item No.: 7003-SchutzAB guard grating (size in accordance to your requirement) Item No.: 7003-UStAB support for just sealed units
(size in accordance to your requirement)
7201-AB_GB.doc 03.09.2008 subject to changes 1/2
Kombi 7201-AB
for vertical lifting and transporting the perfect device for the warehouse Description increased safety via 2 independent vacuum circuits
each vacuum circuit is designed with 2-fold safety acording to EN 13155 & prEN 13035-1 & prEN 13035-2 each vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter 2 completely closed vacuum circuits
prevent loss of vacuum at power failure warning lamp and acoustic signal indicate
insufficient vacuum power failure monitoring system single row arrangement of suction cups
with additional supporting suction cups suction cups fixed directly on the frame outer suction cup distance adjustable via moving of the carrying
bars outer suction cups lockable modular device construction vertical transport approx. 85° guide handles are adjustable in the height Vacuum Generation built-in low maintenance vacuum pump (dry running system) for mains supply Control Means ON/OFF directly at the device SUCTION/RELEASE via cable remote control
optional via infrared remote control
Suspension: 2-fold crane string Safe Working Load: 1000 kg Colour: yellow / partly zinked The turnable suspension allows the picking-up/depositing of large sheets (horizontal to vertical/vertical to horizontal).
vertical
picking-up
2-circuit vacuum lifting device according to
EN 13155
7201-AB_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups rubber black - abrasion possible - up to 100° C heat resistance number of suction cups 2 x 4 2 x 6 carrying bar length minimum approx. mm maximum approx. mm
2200 3500
2900 3500
safe working load on smooth and clean surface at 60 % vacuum at EC construction sites kg in-plant kg
400 800
600 1000
dead weight approx. kg 90 100 structural depth approx. mm vacuum infeed connection 9 mm output 6.0 m³/h voltage 400 Volt 50 Hz 3 Ph Item No.: 7201-AB... 8-0910-400 12-0910-400
output 3.0 m³/h voltage 230 Volt 50 Hz Item No.: 7201-AB... 8-0910 12-0910
output 3.0 m³/h voltage 110 Volt 50 Hz Item No.: 7201-AB... 8-0910-110 12-0910-110 Special Design and Special Voltage
on request
Accessories on request Item No.: 388-SCHUTZ protection cap for suction cup 388 Item No.: 7003- DSFUS2 infrared remote control SUCTION/RELEASE Item No.: 7003-DSFUST infrared remote control SUCTION/RELEASE
only outside the EC Item No.: 7003-WL large warning lamp (flash light for collecting failures) Item No.: 7003-SchutzAB guard grating (size in accordance to your requirement) Item No.: 7003-UStAB support for just sealed units
(size in accordance to your requirement)
battery-supplied, e
#TB_7011_GB.doc
7011-xx Carrying Frame with lectric vacuum pump
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
#TB_ablegen_GB.doc 26.04.2008 1/1
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 e-Mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Possibilities of the Transport Movements
vertical
picking-up vertical – horizontal horizontal – vertical
only via the lower edge
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
7011-ABs_GB.doc 03.09.2008 subject to changes 1/2
Accu-Device Kombi 7011-ABs
for vertical lifting and transporting the perfect device for the warehouse Description 1-circuit vacuum system the vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter completely closed vacuum circuit
prevents loss of vacuum at power failure warning lamp and acoustic signal indicate
insufficient vacuum single row arrangement of suction cups
with additional supporting suction cups suction cups fixed directly on the frame distance of suction cups cannot be adjusted outer suction cups lockable modular device construction vertical transport approx. 85° guide handles are adjustable in the height Vacuum Generation built-in low maintenance rechargeable battery vacuum pump
(dry running system) for rechargeable battery and line operation without change-over built-in accumulator charger for charging over night no change of rechargeable battery necessary no cable - no hose Control Means ON/OFF directly at the device SUCTION/RELEASE via cable remote control
optional via infrared remote control
Suspension: 2-fold crane string Safe Working Load: 1000 kg Colour: yellow The turnable suspension allows the picking-up/depositing of large sheets (horizontal to vertical/vertical to horizontal).
vertical
picking-up
For operation on EC construction sites only
permissible with mechanical holding device
according to EN 13155
7011-ABs_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups black rubber
abrasion possible up to 100° C heat resistant
number of suction cups 6 10 carrying bar length approx. mm 3000 3500 safe working load on smooth and clean surface at 60 % vacuum kg
500
1000
dead weight approx. kg structural depth approx. mm output 1.5 m³/h voltage charger for battery 230 Volt 50 Hz Item No.: 7011-AB... 6-0910 10-0910 voltage charger for battery 110 Volt 50 Hz Item No.: 7011-AB... 6-0910-110 10-0910-110 Special Design and Special Voltage
on request
Accessories on request Item No.: 388-SCHUTZ protection cap for suction cup 388 Item No.: 7003- DSFUS2 infrared remote control SUCTION/RELEASE Item No.: 7003-DSFUST infrared remote control SUCTION/RELEASE
only outside the EC Item No.: 7003-SchutzAB guard grating (size in accordance to your requirement) Item No.: 7003-UStAB support for just sealed units
(size in accordance to your requirement)
Also available as 2-circuit vacuum lifting device (Type 7211-ABs) in accordance to EN 13155 / prEN 13035.
7011-AB_GB.doc 03.09.2008 subject to changes 1/2
Accu-Device Kombi 7011-AB
for vertical lifting and transporting the perfect device for the warehouse Description 1-circuit vacuum system the vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter completely closed vacuum circuit
prevents loss of vacuum at power failure warning lamp and acoustic signal indicate
insufficient vacuum single row arrangement of suction cups
with additional supporting suction cups suction cups fixed directly on the frame outer suction cup distance adjustable via moving of the carrying
bars outer suction cups lockable modular device construction vertical transport approx. 85° guide handles are adjustable in the height Vacuum Generation built-in low maintenance rechargeable battery vacuum pump
(dry running system) for rechargeable battery and line operation without change-over built-in accumulator charger for charging over night no change of rechargeable battery necessary no cable - no hose Control Means ON/OFF directly at the device SUCTION/RELEASE via cable remote control
optional via infrared remote control
Suspension: 2-fold crane string Safe Working Load: 1000 kg Colour: yellow / partly zinked The turnable suspension allows the picking-up/depositing of large sheets (horizontal to vertical/vertical to horizontal).
vertical
picking-up
For operation on EC construction sites only
permissible with mechanical holding device
according to EN 13155
7011-AB_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups black rubber
abrasion possible up to 100° C heat resistant
number of suction cups 6 10 carrying bar length minimum approx. mm maximum approx. mm
2200 3500
2900 3500
safe working load on smooth and clean surface at 60 % vacuum kg
500
1000
dead weight approx. kg 90 100 structural depth approx. mm output 1.5 m³/h voltage charger for battery 230 Volt 50 Hz Item No.: 7011-AB... 6-0910 10-0910 voltage charger for battery 110 Volt 50 Hz Item No.: 7011-AB... 6-0910-110 10-0910-110 Special Design and Special Voltage
on request
Accessories on request Item No.: 388-SCHUTZ protection cap for suction cup 388 Item No.: 7003- DSFUS2 infrared remote control SUCTION/RELEASE Item No.: 7003-DSFUST infrared remote control SUCTION/RELEASE
only outside the EC Item No.: 7003-SchutzAB guard grating (size in accordance to your requirement) Item No.: 7003-UStAB support for just sealed units
(size in accordance to your requirement)
Also available as 2-circuit vacuum lifting device (Type 7211-AB) in accordance to EN 13155 / prEN 13035.
battery-supplied, e
#TB_7211_GB.doc
7211-xx Carrying Frame with lectric vacuum pump
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
#TB_ablegen_GB.doc 26.04.2008 1/1
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 e-Mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Possibilities of the Transport Movements
vertical
picking-up vertical – horizontal horizontal – vertical
only via the lower edge
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Accu-Device Kombi 7211-ABs
for vertical lifting and transporting the perfect device for the warehouse Description • increased safety via 2 independent vacuum circuits
each vacuum circuit is designed with 2-fold safety • acording to EN 13155 & prEN 13035-1 & prEN 13035-2 • each vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter • 2 completely closed vacuum circuits
prevent loss of vacuum at power failure • warning lamp and acoustic signal indicate
insufficient vacuum • power failure monitoring system • single row arrangement of suction cups
with additional supporting suction cups • suction cups fixed directly on the frame • fixed suction cup spacing • outer suction cups lockable • modular device construction • vertical transport approx. 85° • guide handles are adjustable in the height Vacuum Generation • built-in low maintenance rechargeable battery vacuum pump
(dry running system) • for rechargeable battery and line operation without change-over • built-in accumulator charger for charging over night • no change of rechargeable battery necessary • no cable - no hose Control Means • ON/OFF directly at the device • SUCTION/RELEASE via cable remote control
optional via infrared remote control
2-circuit vacuum lifting device according to
EN 13155
vertical
7211-ABs_GB.doc 10.09.2008 subject to changes 1/2
Suspension: 2-fold crane string Safe Working Load: 1000 kg Colour: yellow / partly zinked The turnable suspension allows the picking-up/depositing of large sheets (horizontal to vertical/vertical to horizontal).
picking-up
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups black rubber
abrasion possible up to 100° C heat resistant
number of suction cups 2 x 4 2 x 6 carrying bar length approx. mm 3000 3500 safe working load on smooth and clean surface at 60 % vacuum at EC construction sites kg in-plant kg
400 800
600 1000
dead weight approx. kg structural depth approx. mm output 1.5 m³/h voltage charger for battery 230 Volt 50 Hz Item No.: 7211-ABs... 8-0910 12-0910 voltage charger for battery 110 Volt 50 Hz Item No.: 7211-ABs... 8-0910-110 12-0910-110 Special Design and Special Voltage
on request
Accessories on request Item No.: 388-SCHUTZ protection cap for suction cup 388 Item No.: 7003- DSFUS2 infrared remote control SUCTION/RELEASE Item No.: 7003-DSFUST infrared remote control SUCTION/RELEASE
only outside the EC Item No.: 7003-WL large warning lamp (flash light for collecting failures) Item No.: 7003-SchutzAB guard grating (size in accordance to your requirement) Item No.: 7003-UStAB support for just sealed units
(size in accordance to your requirement)
7211-ABs_GB.doc 10.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
7211-AB_GB.doc 03.09.2008 subject to changes 1/2
Accu-Device Kombi 7211-AB
for vertical lifting and transporting the perfect device for the warehouse Description increased safety via 2 independent vacuum circuits
each vacuum circuit is designed with 2-fold safety acording to EN 13155 & prEN 13035-1 & prEN 13035-2 each vacuum circuit has a vacuum tank with nonreturn valve,
vacuum switch and control vacuum meter 2 completely closed vacuum circuits
prevent loss of vacuum at power failure warning lamp and acoustic signal indicate
insufficient vacuum power failure monitoring system single row arrangement of suction cups
with additional supporting suction cups suction cups fixed directly on the frame outer suction cup distance adjustable via moving of the carrying
bars outer suction cups lockable modular device construction vertical transport approx. 85° guide handles are adjustable in the height Vacuum Generation built-in low maintenance rechargeable battery vacuum pump
(dry running system) for rechargeable battery and line operation without change-over built-in accumulator charger for charging over night no change of rechargeable battery necessary no cable - no hose Control Means ON/OFF directly at the device SUCTION/RELEASE via cable remote control
optional via infrared remote control
Suspension: 2-fold crane string Safe Working Load: 1000 kg Colour: yellow / partly zinked The turnable suspension allows the picking-up/depositing of large sheets (horizontal to vertical/vertical to horizontal).
vertical
picking-up
2-circuit vacuum lifting device according to
EN 13155
7211-AB_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups black rubber
abrasion possible up to 100° C heat resistant
number of suction cups 2 x 4 2 x 6 carrying bar length minimum approx. mm maximum approx. mm
2200 3500
2900 3500
safe working load on smooth and clean surface at 60 % vacuum at EC construction sites kg in-plant kg
400 800
600 1000
dead weight approx. kg 90 100 structural depth approx. mm output 1.5 m³/h voltage charger for battery 230 Volt 50 Hz Item No.: 7211-AB... 8-0910 12-0910 voltage charger for battery 110 Volt 50 Hz Item No.: 7211-AB... 8-0910-110 12-0910-110 Special Design and Special Voltage
on request
Accessories on request Item No.: 388-SCHUTZ protection cap for suction cup 388 Item No.: 7003- DSFUS2 infrared remote control SUCTION/RELEASE Item No.: 7003-DSFUST infrared remote control SUCTION/RELEASE
only outside the EC Item No.: 7003-WL large warning lamp (flash light for collecting failures) Item No.: 7003-SchutzAB guard grating (size in accordance to your requirement) Item No.: 7003-UStAB support for just sealed units
(size in accordance to your requirement)
compressed air-operated vacuum
#TB_7005_GB.doc
7005-xx Carrying Frames with pump / venturi jet(s)
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
#TB_ablegen_GB.doc 26.04.2008 1/1
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 e-Mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
Possibilities of the Transport Movements
vertical
picking-up vertical – horizontal horizontal – vertical
only via the lower edge
Visit our Internet-Page http://www.pannkoke.com
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
7005-AB_GB.doc 03.09.2008 subject to changes 1/2
Venturi Device 7005-AB
for vertical lifting and transporting the perfect device for the warehouse Description 1-circuit vacuum system completely closed vacuum circuit
prevents loss of vacuum at compressed air failure vacuum tank with nonreturn valve control vacuum meter on the device single row arrangement of suction cups
with additional supporting suction cups suction cups fixed directly on the frame outer suction cup distance adjustable via moving of the carrying
bars outer suction cups lockable modular device construction vertical transport approx. 85° guide handles are adjustable in the height Vacuum Generation via built-in suction jet (Venturi)
for operation at least 6 bars compressed air are necessary Control Means air pressure ON/OFF directly at the device SUCTION/RELEASE via hand valve at the device Suspension: 2-fold crane string Safe Working Load: 1000 kg Colour: yellow / partly zinked The turnable suspension allows the picking-up/depositing of large sheets (horizontal to vertical/vertical to horizontal).
vertical
picking-up
1-Circuit Vacuum Lifting Device
for the use outside the EC
7005-AB_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups black rubber
abrasion possible up to 100° C heat resistant
number of suction cups 6 10 carrying bar length minimum approx. mm maximum approx. mm
2900 3500
2900 3500
safe working load on smooth and clean surface at 60 % vacuum kg
500
1000
dead weight approx. kg 90 110 air pressure connection quick release coupling
9 mm
Item No.: 7000-AB... 06-0910 10-0910 Special Design
on request
Accessories on request Item No.: 388-SCHUTZ protection cap for suction cup 388 Item No.: 7003-SchutzAB guard grating (size in accordance to your requirement) Item No.: 7003-UStAB support for just sealed units
(size in accordance to your requirement)
Also available as 2-circuit vacuum lifting device (Type 7205-AB) in accordance to EN 13155 / prEN 13035.
Also available with a power failure monitoring system for the use within the EC.
7005-ABE_GB.doc 03.09.2008 subject to changes 1/2
Venturi Device 7005-AB/E
for vertical lifting and transporting the perfect device for the warehouse Description 1-circuit vacuum system completely closed vacuum circuit
prevents loss of vacuum at compressed air failure vacuum tank with nonreturn valve power failure monitoring system control vacuum meter on the device single row arrangement of suction cups
with additional supporting suction cups suction cups fixed directly on the frame outer suction cup distance adjustable via moving of the carrying
bars outer suction cups lockable modular device construction vertical transport approx. 85° guide handles are adjustable in the height RELEASE-function with overpressure
for short cycle intervals Vacuum Generation via built-in suction jet (Venturi)
for operation at least 6 bars compressed air are necessary Control Means air pressure ON/OFF directly at the device SUCTION via a touch valve RELEASE via two touch valves Suspension: 2-fold crane string Safe Working Load: 1000 kg Colour: yellow / partly zinked The turnable suspension allows the picking-up/depositing of large sheets (horizontal to vertical/vertical to horizontal).
vertical
picking-up
1-circuit vacuum lifting device according to
EN 13155
7005-ABE_GB.doc 03.09.2008 subject to changes 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
suitable for lifting material properties
gas-tight
surface smooth e. g. glass panes, insulation glass units, plastic and ceramic plates,
coated boards suction cup type 388 diameter in action approx. mm 300 quality of suction cups black rubber
abrasion possible up to 100° C heat resistant
number of suction cups 6 10 carrying bar length minimum approx. mm maximum approx. mm
2900 3500
2900 3500
safe working load on smooth and clean surface at 60 % vacuum kg
500
1000
dead weight approx. kg 90 110 air pressure connection quick release coupling
9 mm
Item No.: 7005-AB/E... 06-0910 10-0910 Special Design
on request
Accessories on request Item No.: 388-SCHUTZ protection cap for suction cup 388 Item No.: 7003-SchutzAB guard grating (size in accordance to your requirement) Item No.: 7003-UStAB support for just sealed units
(size in accordance to your requirement)
Also available as 2-circuit vacuum lifting device (Type 7205-AB) in accordance to EN 13155 / prEN 13035.
www.pannkoke.com
Vacuum Pump 7002-COMP
in the crane rail
Vacuum Pump 7002-COMP
in the crane rail
Frame 7000-A
Kombi 7001-AS
Frame 7000-A
Manipulation Device 7025-MS
Load testing of an individual suction cup
Vacuum Lifting Units Servicing by the
Specialist
Serviceangebot_GB.doc 30.04.2008 2/2
Address: Haendelweg 5 D-23556 Luebeck Germany Phone: +49 451 47008-0 E-mail: [email protected] Fax: +49 451 47008-37 Internet: http://www.pannkoke.com
We, Pannkoke Flachglastechnik GmbH, are a specialist company that manufactures equipment, machines and tools for the glass processing industry. Our medium-sized engineering company was founded in 1900. Since 1958, we have been developing and producing practical vacuum lifting devices and flat glass cutting machines. Due to our many years of experience, we have also distinguished ourselves as leaders in fulfilling extraordinary customer wishes and requirements in respect to vacuum lifting device needs. Individual customised solutions are our strong point, as many of our customers can confirm.
Services offered
Repair and maintenance of flat glass cutting machines Maintenance and testing of vacuum lifting units
We carry out the annually prescribed tests of the trade accident prevention and insurance association for vacuum lifting units (see BGR 500, sections 2.8, 3.12.2, regular testing), either in our factory or at your own site. The units are checked point-by-point according the requirements of the safety standard, EN 13155. . We don’t only inspect the units, we also carry out load testing or check the load-bearing capacity of the suction cup. In our factory, we carry out load tests up to 3000kg with samples measuring up to 4 x 2m. When carrying out on-site testing, we check the load bearing capacity of individual suction cups, rather that the load bearing capacity of the whole unit, using our specially developed portable suction cup testing device. We have the benefit of almost 50 years of knowledge and experience, so that unit safety really can be guaranteed.
Testing of the load bearing capacity of suction cups Repair of vacuum lifting units Repair of hand suction holders (Powr Grip) Conversion of vacuum lifting units from single circuit to 2-circuit technology
General information and test reports can be obtained from us:
General information on vacuum lifting units What to check when purchasing a new vacuum lifting unit Test results from Kiel higher technical college – vacuum technology Training in the use of vacuum lifting units
You can contact us at: Telephone: +49 451 / 47008-0 Fax: +49 451 / 47008-37 e-mail: [email protected] www.pannkoke.com