paper international journal of informative & futuristic ... · international journal of...

8
2539 www.ijifr.com Copyright © IJIFR 2015 Research Paper International Journal of Informative & Futuristic Research ISSN (Online): 2347-1697 Volume 2 Issue 8 April 2015 Abstract Simulation of compressors in an Ammonia synthesis unit (Production of ammonia) process is gaining importance and so the process needs to be studied .With the advent of computers and simulating software’s like “ASPEN PLUS” it is possible to design and optimize a particular process. A Multi-stage Compressor is taken into consideration and hence-forth simulation is done controlling the pressure, increasing at stages and reducing the volume. Proper design can significantly reduce production cost as well as provide to make the process safe and reduce environment hazards. Steady state simulation is done. Each unit is taken into consideration and the variables are been optimized. The units are sequentially optimized. 1. Introduction In industry complicated problems are often not solved by hand for two reasons: human error and time constraints. There are many different simulation programs used in industry depending on the field, application, and desired simulation products (entire process unit, one piece of equipment, etc.). When used to its full capabilities, Aspen can be a very powerful tool for a Chemical Engineer in a variety of fields including oil and gas production, refining, chemical processing, environmental studies, and power generation to name a few. Process simulation allows you to predict the behaviour of a process by using basic engineering relationships, such as mass and energy balances, and phase and chemical equilibrium. Given reliable Simulation of Compressors by Aspen Plus Paper ID IJIFR/ V2/ E8/ 013 Page No. 2539-2546 Subject Area Chemical Engineering Key Words Simulation, Design, Compressors, Steady State, Dynamic Nimesh Kamat 1 B.E. Student, Department of Chemical Engineering, Bharati Vidyapeeth College Of Engineering, Navi Mumbai-Maharashtra, India Dr. S.M. Walke 2 Professor, Department of Chemical Engineering, Bharati Vidyapeeth College Of Engineering, Navi Mumbai-Maharashtra, India

Upload: lydang

Post on 05-Sep-2018

223 views

Category:

Documents


0 download

TRANSCRIPT

2539

www.ijifr.com Copyright © IJIFR 2015

Research Paper Paper

International Journal of Informative & Futuristic Research ISSN (Online): 2347-1697

Volume 2 Issue 8 April 2015

Abstract

Simulation of compressors in an Ammonia synthesis unit (Production of

ammonia) process is gaining importance and so the process needs to be studied

.With the advent of computers and simulating software’s like “ASPEN PLUS” it is

possible to design and optimize a particular process. A Multi-stage Compressor is

taken into consideration and hence-forth simulation is done controlling the

pressure, increasing at stages and reducing the volume. Proper design can

significantly reduce production cost as well as provide to make the process safe

and reduce environment hazards. Steady state simulation is done. Each unit is

taken into consideration and the variables are been optimized. The units are

sequentially optimized.

1. Introduction

In industry complicated problems are often not solved by hand for two reasons: human error and

time constraints. There are many different simulation programs used in industry depending on the

field, application, and desired simulation products (entire process unit, one piece of equipment, etc.).

When used to its full capabilities, Aspen can be a very powerful tool for a Chemical Engineer in a

variety of fields including oil and gas production, refining, chemical processing, environmental

studies, and power generation to name a few.

Process simulation allows you to predict the behaviour of a process by using basic engineering

relationships, such as mass and energy balances, and phase and chemical equilibrium. Given reliable

Simulation of Compressors by Aspen Plus Paper ID IJIFR/ V2/ E8/ 013 Page No. 2539-2546 Subject Area

Chemical

Engineering

Key Words Simulation, Design, Compressors, Steady State, Dynamic

Nimesh Kamat 1

B.E. Student, Department of Chemical Engineering, Bharati Vidyapeeth College Of Engineering, Navi Mumbai-Maharashtra, India

Dr. S.M. Walke 2

Professor, Department of Chemical Engineering, Bharati Vidyapeeth College Of Engineering, Navi Mumbai-Maharashtra, India

2540

ISSN (Online): 2347-1697 International Journal of Informative & Futuristic Research (IJIFR)

Volume - 2, Issue - 8, March 2015 20th Edition, Page No: 2539-2546

Nimesh Kamat , Dr. S.M. Walke :: Simulation of Compressors by Aspen Plus

thermodynamic data, realistic operating conditions, and rigorous equipment models, you can

simulate actual plant behaviour. Process simulation enables you to run many cases, conduct "what

if" analyses, and perform sensitivity studies and optimization runs. With simulation, you can design

better plants and increase profitability in existing plants.

a) Simulation Modes:

There are two modes of simulation-

1) Steady state mode

2) Dynamic mode.

b) Steady State Mode and Dynamic Mode :-

A simulation program may be used for steady state or dynamic simulation. In the first case, a

material and energy balance for steady state operation of the chemical plant must be done. In the

second case, the time varying operation of the plant is simulated. Dynamic simulation is the more

complicated and computationally expensive of the two. Initially process simulation was used to

simulate steady state processes.

Dynamic simulation is an extension of steady-state process simulation whereby time-dependence is

built into the models via derivative terms i.e. accumulation of mass and energy.

Dynamic simulations require increased calculation time and are mathematically more complex than

a steady state simulation. It can be seen as a multiply repeated steady state simulation (based on a

fixed time step) with constantly changing parameters.

Dynamic simulation can be used in both online and offline fashion. The online case being model

predictive control, where the real-time simulation results are used to predict the changes that would

occur for a control input change and the control parameters are optimized based on the results.

c) Various Process Simulators:-

Aspen Plus.

Aspen Hysys.

Aspen Custom Modeller by Aspen Technology.

CHEMASIM.

CHEMCAD.

2. Aspen PLUS Process Simulator

Aspen PLUS process simulator is a core element of engineering applications. It provides quite

accurate results which makes it an efficient simulator. It provides comprehensive thermodynamics

basis for accurate determination of physical properties, transport properties, and phase behaviour.

Aspen PLUS can be used to determine outlet process conditions if the inlet conditions like

temperature, pressure, and composition are specified. Aspen PLUS has established itself as a very

intuitive and easy to use process simulator in oil and gas refining industry. Users with little prior

knowledge of Aspen PLUS can pick up and train themselves in its modelling capabilities. Some of

the very intuitive capabilities include a highly interactive process flow diagram for building and

2541

ISSN (Online): 2347-1697 International Journal of Informative & Futuristic Research (IJIFR)

Volume - 2, Issue - 8, March 2015 20th Edition, Page No: 2539-2546

Nimesh Kamat , Dr. S.M. Walke :: Simulation of Compressors by Aspen Plus

navigating through large simulations. The program also provides a very flexible and easy to use

distillation column modelling environment. Additionally the interactive nature of PLUS enables

users to build and use their models quickly and effectively.

2.1 Description

Before Starting with simulation we have to select the available simulation templates as shown in

fig.1. There are numerous options and the highlighted one is generally the solution to all and or can

solve as seen by the no of available templates.

Figure 1: Available Simulation Templates

Aspen has a huge database of commonly used (and some not so commonly used) components and

their physical properties. It also has an option where a user can define components that are not

included in the database. Under the Specifications option we will input our components in the

Selection tab. While making the PFD material streams are specified and entered. This is the only

option where we will need to input data under the Components tab as shown in fig 2.

Figure 2: Component Selection

2542

ISSN (Online): 2347-1697 International Journal of Informative & Futuristic Research (IJIFR)

Volume - 2, Issue - 8, March 2015 20th Edition, Page No: 2539-2546

Nimesh Kamat , Dr. S.M. Walke :: Simulation of Compressors by Aspen Plus

By knowing all the required data, process inputs we simulate the flow sheet. By knowing the

specific volume with the help of equation of state we can determine the size and thus cost of the

plant. Fig.3 represents the Aspen Plus screen where one will be able to draw the flow sheet and also

simulate it by adding numerous inputs and also can check the energy analysis.

Figure 3: Aspen Plus Screen

3. Working With Process Equipment’s

3.1 What does a Compressor do?

A compressor is a mechanical device like a pump that is used in various different applications.

Compressors are work absorbing devices which are used for increasing pressure of fluid at the

expense or work done on fluid. The compressors used for compressing air are called air

compressors. Compressors are invariably used for all applications requiring high pressure air. Some

of popular applications of compressor are, for driving pneumatic tools and air operated equipment’s,

spray painting, compressed air engine, supercharging surface cleaning, refrigeration and air

conditioning, chemical industry etc. compressors are supplied with low pressure air (or any fluid) at

inlet which comes out as high pressure air (or any fluid) at outlet. Work required for increasing

pressure of air is available from the prime mover driving the compressor. Generally, electric motor,

internal combustion engine or steam engine, turbine etc. are used as prime movers. Compressors are

similar to fans and blowers but differ in terms of pressure ratios. Fan is said to have pressure ratio up

to 1.1 and blowers have pressure ratio between 1.1 to 4 while compressors have pressure ratios more

than 4.

2543

ISSN (Online): 2347-1697 International Journal of Informative & Futuristic Research (IJIFR)

Volume - 2, Issue - 8, March 2015 20th Edition, Page No: 2539-2546

Nimesh Kamat , Dr. S.M. Walke :: Simulation of Compressors by Aspen Plus

3.2 Types of Compressors

Figure 4: Types of Compressors

Compressors are generally divided into two categories:

• Positive Displacement Compressors

• Dynamic Compressors

Positive displacement compressors in essence work by entrapping a volume of gas and

subsequently reducing this volume which in turn increases the pressure.

Dynamic compressors generally work by imparting movement to the gas; i.e. kinetic energy

is transferred from the machines internals to the gas. By subsequent reduction of this

velocity the kinetic energy is converted into potential energy – pressure.

The image above shows the available types of compressors. The most common ones used in

refrigeration are described below:

3.3 Working with Compressor

The compressor operation is used to increase the pressure on inlet gas stream. Depending on the

information specified, the compressor calculates either a unknown temperature, pressure or

compressor efficiency.

The Compressor block can be used to simulate:

Polytrophic Centrifugal compressor

Polytrophic positive displacement compressor

Isentropic compressor

Isentropic turbine

M Compressor is used for multi-stage compressors. Power requirement is calculated or input. A

Heater model can be used for pressure change calculations only. Compressor is designed to handle

both single and multiple phase calculations. Rating can be done by specifying a compressor

performance curve.

Specify:

Dimensional curves

Head versus flow.

2544

ISSN (Online): 2347-1697 International Journal of Informative & Futuristic Research (IJIFR)

Volume - 2, Issue - 8, March 2015 20th Edition, Page No: 2539-2546

Nimesh Kamat , Dr. S.M. Walke :: Simulation of Compressors by Aspen Plus

Power versus flow.

Head coefficient versus flow coefficient.

3.4 Compressors in Aspen Plus

A compressor in Aspen Plus takes similar inputs and output material and work streams as

that of a pump.

Figure 5:- Compressor in Aspen Plus

Unlike pumps, here you need to specify the compressor operating conditions, based on

experience or manufacturer recommendations and information.

The outlet conditions can be either input directly as pressure specification, determined from

input power, or determined from performance curves.

If the last option is used, the performance curve must be given in Performance Curves sheet

in a similar manner to that for the pump.

The pump efficiency can be input directly as a scalar quantity, or it can be calculated from

efficiency curves. In both cases, the efficiency will have a direct effect on BHP calculations for

the compressor.

Figure 6:- Compressor Specifications Sheet

2545

ISSN (Online): 2347-1697 International Journal of Informative & Futuristic Research (IJIFR)

Volume - 2, Issue - 8, March 2015 20th Edition, Page No: 2539-2546

Nimesh Kamat , Dr. S.M. Walke :: Simulation of Compressors by Aspen Plus

4. Simulation of Compressor in Aspen plus

The figure below represents the schematic diagram of compressor in aspen plus. The feed comes

into the compressor 1 and then it is cooled in a cooler 1 and then again for increasing the pressure it

goes in compressor 2 and cooled in cooler 2.

Figure 7: Simulation of Compressor

The feed conditions are as follows:-

Table 1:- Feed Input

FEED

Temperature F 75

Pressure psia 14.7

Vapor Frac 1

Mole Flow lbmol/hr 128.51

Mass Flow lb/hr 3600

Volume Flow cuft/hr 50157.4

Enthalpy MMBtu/hr -0.002

Mole Flow lbmol/hr

NITRO-01 128.51

Table 2:- Simulation Result

2546

ISSN (Online): 2347-1697 International Journal of Informative & Futuristic Research (IJIFR)

Volume - 2, Issue - 8, March 2015 20th Edition, Page No: 2539-2546

Nimesh Kamat , Dr. S.M. Walke :: Simulation of Compressors by Aspen Plus

5. Conclusion

The goal of Plus is to provide a capability to design an entire process completely and accurately.

Steady-state simulation is a powerful process engineering tool that enables engineers to simulate

plant behaviour and analyse their results rapidly. The process simulation capabilities of Aspen Plus

enables engineers to predict the behaviour of a process using basic engineering relationships such as

mass and energy balances, phase and chemical equilibrium, and reaction kinetics. With reliable

thermodynamic data, realistic operating conditions and the rigorous Aspen Plus equipment models,

they can simulate actual plant behaviour. Aspen Plus provides an extremely powerful approach to

steady state modelling. Aspen brings the power of steady-state process simulation to the engineering

desktop, and delivers both modelling power and ease of use. With Aspen Plus, companies can

design, simulate, troubleshoot and manage profitable process plants. It solves the critical engineering

and operating problems that arise throughout the lifecycle of a chemical process, such as designing a

new process, troubleshooting a process unit or optimizing operations of a full process like an

Ammonia synthesis plant.

Acknowledgements

This work was done by Nimesh Kamat as a part of their BE project work during June 2014 to Feb

2015,at the Department of Chemical Engineering, Bharati Vidyapeeth College of Engineering, Navi

Mumbai, India, under the guidance of Dr. S.M. Walke. We are thankful to the authorities at Bharati

Vidyapeeth College of Engineering, Navi Mumbai for providing all facilities for completing this

work.

References

[1] Mohd.Kamaruddin Abd Hamid “Plus: An introduction to Chemical Engineering Simulation”.

[2] Michael E Hanyak “Chemical Process Simulation and Aspen tech Plus Software” Version 2006 Bucknell

university Lewisburg PA 17837 December 15 2007.

[3] Aspen Plus@ 2004.2 Dynamic Modeling.[5] Issues addresses by Process Modeling (Aspen Plus) V7.2

Cumulative patch 2, September 2010.

[4] Teemu, T.S., Pekka, R., Juha, H., Jari, B., “Predicting off-design range and performance of two-stage

centrifugal compressor ”, International Journal of Refrigeration, 33 (6), 1152-1160 (2010).

5] MIT, Aspen-tech, User’s Guide of ASPEN PLUS 10, USA (2001).

[6] Luyben W. L., Distillation Design and Control Using Aspen Simulation, Wiley, New

York (2006).