auhippo.com · part - b (5 x 16 = 80 marks) auhippo.com write short notes on : (i) design process...

2

Upload: others

Post on 31-Dec-2019

2 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: auhippo.com · PART - B (5 x 16 = 80 Marks) auhippo.com Write short notes on : (i) Design process (ii) CAD system architecture OR What is meant by concurrent engineering ? Describe

Page 2: auhippo.com · PART - B (5 x 16 = 80 Marks) auhippo.com Write short notes on : (i) Design process (ii) CAD system architecture OR What is meant by concurrent engineering ? Describe

auhippo.com...14. (a) Explain the indirect methods of contouring. auhippo.com (b) (i) An embankment of width 8 m and side slopes 1.5:1 is required to be made on a ground which is levelled

auhippo.com · 2019-03-20 · 15. auhippo.com (a) Determine the gradient from a point A to point B from the following observations made with a tachometer fitted with an analytic lens

auhippo.com...microprocessor. auhippo.com Explain the vectored interrupts in 8051 microcontroller. Explain the different addressing modes of 8051 microcontroller. OR (l Explain with

Monday 3 August 2020...0810-0825 0825-0835 0835-1010 Chair: 0835-0920 0920-0925 Chair 0925-1010 1010-1020 1020-1150 Concurrent 1A Concurrent 1B Concurrent 1C Concurrent 1D Concurrent

auhippo.com · Draw SFD and 'BMD and indicates the salient features of beam loaded (16) Fig. Q. 12. (a) auhippo.com 15kN 10 kN/m 7m Fig, Q. 12. (a) OR 1.50 m (i) Find the dimensions

auhippo.com...Electrical and Electronics Engineering EE 6703 — SPECIAL ELECTRICAL MACHINES Three hours (Regulations 2013) auhippo.com Answer ALL questions. PART A— (10 x 2 = 20

auhippo.com...12. 13. 15, auhippo.com PART - B (5 x 16 = 80 Marks) auhippo.com (a) Draw the circuit diagram of a single stage Common Emitter amplifier that emitter current feedback

auhippo.com...Define method study and state the three different levels in method study. What is meant by work measurement ? Define value analysis. What is meant by line balancing ?

Concurrent Forces

CONCURRENT ENGINEERING METHODS · Concurrent Engineering The Aerial Robot's Design Environment Why Were Concurrent Engineering Techniques Important to this Project? II. HOW WAS CONCURRENT

auhippo.com · 2019-03-20 · (a) Explain the various types of constructors that are available in C++ with suitable examples Or (b) What is meant by polymorphism? Explain the various

Concurrent Processing

Introduction: Concurrent Programming - Concurrent …Every concurrent programming model must answer two questions: 1. How to express that two executions are concurrent? ... The second

auhippo.com · 2019-03-20 · 50446 auhippo.com PART-B 11. a) Draw the architecture and explain the functional units of 8086. (OR) b) Describe the interrupts of 8086 and its types

auhippo.com...EC 6302 — DIGITAL ELECTRONICS (Common to Mechatronics Engineering and Robotics and Automation Engineering) RuhiÞPO' Time : Three hours (Regulations 2013) auhippo.com

auhippo.com€¦ · 15. (b) (a) auhippo.com The amplitude modulated signal is MM (t) = where m(t) is the baseband signal and A cos ((0/+0) is the carrier. The baseband signal m(t)

Concurrent Programming - UNILdoplab.unil.ch/wp-content/uploads/2016/09/2-Concurrent-Programmi… · Concurrent Programming Benoît Garbinato Concurrent Programming © Benoît Garbinato

auhippo.com · 9. auhippo.com 12PT-Oi For a beam carrying a UDL, the strain eneror will be maximum in case the beam is cantilever C) propped cantilever B) simply supported

auhippo.com · DESIGN OF REINFORCED CONCRETE & BRICK MASONRY STRUCTURES (Regulations 2013) auhippo.com Answer ALL questions. PART -A x 2 = 20 Marks) Maximum : 100 Marks ime : Three

auhippo.com · auhippo.com 12. a) Design a 4 bit BCD adder using full adder and explain its structure and compute the circuit to add 1001 and 0101. Write the sum and carry output

auhippo.com · 50859 auhippo.com PART -B (5" 13=65 Marks) ll. a) Write in detail with neat sketcbr any three inversions of double slider crank cham. (OR) b) Describe with neat sketch,

auhippo.com€¦ · B.E./ B.Tech. DEGREE EXAMINATION, MAY/JUNE 2016 Sixth Semester Computer Science and Engineering : Three Hours CS 6660- COMPILER DESIGN (Regulations 2013) auhippo.com

auhippo.com · 12. 13. 15. 16. auhippo.com (a) Explain the system bus structure of 8086. Draw the timing diagram for interrupt acknowledgement cycle. Or (b) Explain the closely looped

auhippo.com...1. 5. 6. The primary objective of formal technical reviews is to : (A) fix errors (B) find errors (C) clear errors (D) modify errors auhippo.com testing method enables

IGDS Concurrent Engineering Module, 25 th February 2003 Concurrent Teams Concurrent Teams Teams IGDS Concurrent Engineering Module, 25 th February 2003

auhippo.com · 2019-03-20 · 12 13. (b) (a) (b) (a) (b) (a) (b) auhippo.com rtto the ton the different tape correctionsv (10) What ts between plane surveying and Geodetic surveying

Training for the Army’s...and prior to even getting on a live-fire range — trainees will conduct concurrent training on rifle marksmanship. All of this concurrent training is meant

auhippo.com · Barkhausen criterion for the sustained oscillations. Also find the frequenc at which the circuit will oscillate. OR auhippo.com Explain the working of a Colpitts oscillator

COURSE CONTENT IN BRIEF 1.Introduction. 2.Resultant of concurrent and non-concurrent coplanar forces. 3.Equilibrium of concurrent and non-concurrent coplanar

Concurrent Queues

auhippo.com · — GAS DYNAMICS AND JT PROPULSION (Regulations 2013) auhippo.com ... State and prove Prandtl — Meyer relation for a normal shock. Or (16) A gas at a pressure of

Effective Concurrent Audit/ Concurrent Audit Reporting

Concurrent & Distributed Systems 2017 Concurrency... · Concurrent & Distributed Systems 2017. ... Principles of Concurrent and Distributed Programming ... “Concurrent programming

Concurrent Engineering

auhippo.com · (b) auhippo.com (i) Explain in detail with cim,l.it diagram of Trms impedance (10) (ii) Consid< a digital -opdc link at a bit rate of 622 Mbps at