part - ii price bidfci.gov.in/app2/webroot/upload/33 raipur bldg. price bidg.pdf · 1997 column...
TRANSCRIPT
1
Contractor Asstt.Genl.Manager(Engg)
FOOD CORPORATION OF INDIA
REGIONAL OFFICE (Chattisgarh)
RAIPUR 492 005.
Name of Work: Construction of single storey RCC framed structure office building for
FCI’s RO (CG) &DO(Raipur) at P.O. Pandri, VidhansabhaMarg, Kapa
Raipur (CG).
Sub Head :RCC framed structure, internal road/ pavement, site development,
watersupply, sanitary, drainage system, internal partition of cabins, false
ceiling and painting, Internal electrification work
PART - II
PRICE BID
The Price Bid containing 2 to 31 pages has been issued to
M/s___________________________________________________________________
Address_______________________________________________________________
_vide cash receipt mentioned in the Technical Bid tender.
Contractor Signature of issuing Officer
Date
Designation
2
Contractor Asstt.Genl.Manager(Engg)
ESTIMATE OF PROPOSED RO/DO BUILDING FCI RAIPUR CG
S.No DSR
IN
PNo Description Qty. Unit Rate Amount
SECTION – A (CIVIL WORK)
1 2.6.1 64 Earth work in excavation by mechanical
means (Hydraulic excavator )/ manual
means over areas (exceeding 30cm in
depth. 1.5m in width as well as 10 sum on plan) including disposal of excavated
earth, lift upto 1.5m including all lead,
disposed earth to be levelled and neatly dressed.
All kinds of soil. 8770.70 Cum
2. 2.26.1 67 Extra for every additional lift of 1.5 m or
part thereof in :
All kinds of soil. 3823.50 Cum
3. 2.25.1 67 Filling from excavated earth (excluding
rock) in trenches, plinth sides of foundation etc in layers not exceeding
20cm. In depth consolidating each
deposited layer by ramming and watering lead upto 50m and lift upto
1.5m.
786.42 Cum
4. Supplying and filling in
trenches,plinth,sides of foundation etc. in layers not exceeding 20cm in depth
cosolidating each deposited layer by
watering, ramming consolidating and dressing etc. complete
A 16.3.9
+2.25
Good earth 5835.31 Cum
B 16.3.10
+2.25
Hard Moorum 2743.67 Cum
5 2.34.1 68 Supplying chemical emulsion in sealed containers including delivery as
specified.
Chlorpyriphos/Lindaneemulsifiable
concentrate of 20%@ 7.5 litres / sqm 3686.25 Litre
6 AR
ON
DSR
Diluting & injecting chemical emulsion
(to be supplied free of cost at site of
work) for preconstructional Anti termite treatment & creating continuous
chemical barrier under &alround the
2457.50 Sqm
3
Contractor Asstt.Genl.Manager(Engg)
1997 column pits, wall trenches, basement
excavation, top surface of plinth filling, junction of wall & floor along the
exterior perimeter of Bldg., expansion
joints, over the top surface of
consolidated earth on which appron is to be laid ,surrounding of pipes & conduits
etc. complete as per specification( Plinth
area of the Bldg. at grround floor only shall be measured for payment) with
chlorpyrithos/ lindaneemulsifiable
concentrate 20% with 1% concentration.
7 Based
on
DSR
rates
providing & laying dry stone rubble soling of 230 mm thk using appropriate
rubble stones in layers, filling the voids
by chips, murum, good earth and consolidation, watering etc. complete as
per the direction of Engineer-in-charge
2457.50 Sqm
8 4.1.5 79 Providing and laying in position cement
concrete of specified grade excluding the cost of centring and shuttering - All work
upto plinth level
1:3:6(1 Cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size)
196.60 Cum
9 4.1.8 79 Providing and laying in position cement
concrete of specified grade excluding the
cost of centring and shuttering - All work upto plinth level
1:4:8 (1 Cement : 4 coarse sand : 8
graded stone aggregate 40 mm nominal
size)
80.18 Cum
10 4.2.3 80 Providing and laying cement concrete in
retaining walls, return walls, walls (any
thickness) including attached pilasters, columns, piers, abutments, pillars, posts,
struts, buttresses, string or lacing
courses, parapets, coping, bed blocks,
anchor blocks, plain window sills, fillets etc. upto floor five level, excluding the
cost of centring, shuttering and finishing
:
1:2:4 (1 Cement : 2 coarse sand : 4
graded stone aggregate 20 mm nominal
size)
4.31 Cum
11 89 Centring and shuttering including strutting, propping etc. and removal of
form work for :
A 5.9.3 Foundations, footings, bases of columns. 1113.17 Sqm
B 5.9.5 89 Suspended floors, roofs , landing ,
balconies and access platform 2748.88 Sqm
C 5.9.6 89 Lintels, beams, plinth beams, girders,
bressumers and cantilevers. 3661.01 Sqm
4
Contractor Asstt.Genl.Manager(Engg)
D 5.9.7 89 Columns, Pillars, Piers, Abutments,
Posts and Struts 2364.83 Sqm
E 5.9.19 89 stairs (excluding landing)except spiral-
staircases. 36.30 Sqm
F 5.22.6 89 Weather shade, Chajjas, corbels etc.,
including edges. 224.93 Sqm
12 5.28 92 Reinforcement for R.C.C. work
including straightening, cutting, bending,
placing in position and binding all
complete. TMT bars
187558.3
3
Kg.
13 5.29.1 92 Providing and fixing in position 12mm
thick bitumen impregnated fibre board
conforming to IS:1838 including cost of primer, sealing compound in expansion
joints.
65.00 Per cm
depth per
cm
14 5.30 92 Providing and fixing sheet covering over
expansion joints with iron screws as per design to match the colour / shade of
wall treatment.Non-asbestos fibre
cement board 6mm thick as per IS:14862 200 MM WIDE
65.00 Per cm
depth per
cm
15 93 Add or deduct for plaster drip
course/groove in plastered surface or
moulding to R.C.C. projections
350.00 Rmt.
16 93 Providing and laying in position ready
mixed concrete manufactured in fully
automatic batching plant 7 transported to
site of work in transit mixture with all leads having
continousagilatedmixture,manufactured
as per mixed design of specified grade for reinforced cement concrete
work,including pumping of RMC from
transit mixture to site of laying, excluding the cost of centring,
shuttering, finishing and
reinforcement.including cost
ofAdmixtures in recommended proportions.(as per is 9103) to accelerate,
retard setting of concrete improve
workability without imparing strength and durability as per direction of
Engineer-in -charge-M-25grade
reinforced cement concrete by using380
kg of cement per cum of concrete all work up to floor V level .
467.33 Cum
17 6.4.2 93 Providing and laying in position ready
mixed concrete manufactured in fully automatic batching plant 7 transported to
site of work in transit mixture with all
leads having
continousagilatedmixture,manufactured as per mixed design of specified grade
1035.96 Cum
5
Contractor Asstt.Genl.Manager(Engg)
for reinforced cement concrete
work,includingpumping of RMC from transit mixture to site of laying,
excluding the cost of centring,
shuttering, finishing and
reinforcement.including cost ofAdmixtures in recommended
proportions.(as per is 9103) to accelerate,
retard setting of concrete improve workability without imparing strength
and durability as per direction of
Engineer-in -charge-M-25grade reinforced cement concrete by using380
kg of cement per cum of concrete all
work up to floor V level .
18 Brick work with F.P.S. bricks of class designation 35 in Superstructure above
plinth level up to floor v level in all
shaps& sizes in
6.13.2 99 Cement mortar 1:6 (1 cement : 6 coarse sand)
392.14 Cum
19 100 Half brick masonry with F.P.S. bricks of
class designation 35 in superstructure above plinth level up to floor V level.
Cement mortar 1:4 (1 Cement : 4 coarse
sand) 228.92 Sqm
20 7.23.1.
5
114 Stone work (machine cut edges) for wall lining etc. (veneer work) backing filled
with a grout of 12mm thick cement
mortar 1:3 (1 cement : 3 coarse sand)
including pointing in white cement mortar 1:2 (1 white cement : 2 stone
dust) with an admixture of pigment
matching the stone shade : (To be secured to the backing by means of
cramps which shall be paid for
separately) :
A 7.23.3.
5
Red sand stone - exposed face fine dressed with rough backing.
1835.00 Sqm
B 7.25 White sand stone - exposed face fine dressed with rough backing.
202.00 Sqm
21 114 Providing and fixing stainless steel
cramps of required size and shape for
anchoring stone wall lining to the backing or securing adjacent stones in
stone wall lining in cement mortar 1:2 (1
cement : 2 coarse sand) including making the necessary chases in stone and
holes in walls wherever required.
871.84 Kg.
8.2.1.2
22 8.10.2 120 Providing and fixing 18mm thick gang 236.72 Sqm
6
Contractor Asstt.Genl.Manager(Engg)
saw cut mirror polished (premoulded and
prepolished) machine cut for kitchen platforms, vanity counters ,window sills ,
facias and similar locations of required
size of approved shade, colour and
texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse
sand) with joints treated with white
cement, mixed with matching pigment, epoxy touch ups, including rubbing,
curing moulding and polishing to edge to
give high gloss finish etc. complete at all levels. Udaipur Green Marble Area of
Slab upto 0.50 sqm
23 8.10 Providing and fixing stone slab table
rubbed, edges rounded and polished of size 75x50 cm deep and 1.8 cm thick
fixed in urinal partitions by cutting a
chase of appropriate width with chase cutter and embedding the stone in the
chase with epoxy grout or with cement
concrete 1:2:4 (1 cement : 2 coarse sand :
4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-
charge and finished smooth.
8.2.2.1 Granite Stone of approved shade. 8.10 Sqm
24 8.3.2 120 Providing and fixing 18mm thick gang
saw cut mirror polished (premoulded and prepolished) machine cut for kitchen
platforms, vanity counters ,window sills ,
facias and similar locations of required size of approved shade, colour and
texture laid over 20mm thick base
cement mortar 1:4 (1 cement : 4 coarse
sand) with joints treated with white cement, mixed with matching pigment,
epoxy touch ups, including rubbing,
curing moulding and polishing to edge to give high gloss finish etc. complete at all
levels. Granite of any colour Area of
slab upto 0.50 sqm.
85.75 Sqm
25 8.4 120 Extra for providing edge moulding to 18mm thick marble stone
counters,Vanities etc. over Item No. 8.2
including machine polishing to edge to give high gloss finish etc. complete as
per design approved by Engineer-in-
Charge
100.00 Rmt
26 10.3 120 Extra for fixing marble / granite stone over and above coresponding basic item,
in facia and drops of width upto 150 mm
with expoxy resin based (Araldite or
100.00 Rmt
7
Contractor Asstt.Genl.Manager(Engg)
equivalent) adhesive including cleaning
etc. complete.
27 10.16.1 164 Providing and fixing in position
collapsible steel shutters with vertical
channels 20x10x2mm and braced with
flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm
with 40mm dia, steel pulleys complete
with bolts, nuts, locking arrangement, stoppers, handles, including applying a
priming coat of approved steel primer.
19.80 Sqm
28 10.26.1 165 Steel work in built up tubular trusses
including cutting, hoisting fixing in position and applying a priming coat of
approved steel primer, welded and bolted
including special shaped washers etc. complete. Hot finished welded type tubes
3456.00 Kg.
29 11.26.1 166 Providing and fixing hand rail by
welding etc. to steel ladder railing,
balcony railing & staircase railing including applying a priming coat of
approved steel primer .M.S. tube (
medium) 40 mm nominal bore
430.00 Kg.
30 11.36.1 176 Kota stone slab flooring over 20mm (average) thick base laid over and
jointed with grey cement slurry mixed
with pigment to match the shade of the slab including rubbing and polishing
complete with base of 1 : 4 ( 1 cement :
4 coarse sand) : 25 mm thick
255.19 Sqm
31 11.39 177 Providing and fixing vitrified wall tiles of size 300x450mm conforming to IS :
15622(thickness to be specified by the
menufecture ) of approved make in all colours , shapes Engineer-in- Charge in
skriting, risers of steps and dados over
12mm thick bed of Cement Mortar 1:3 (1 Cement :3 coarse sand )and Jointing with
grey Cement slurry @ 3.3kg. persqm
including pointing in white Cement
mixer with pigment of matching shade complete.
453.14 Sqm
32 11.41.2 177 Providing and laying mat finish anti
skidvetrified tile flooring of approved shade and brand over a bed of cement
motar 1:4 (1 cement : 4 coarse sand)
20mm thick/pasting with approved
adhesive, as per the flooring design given by the engineer -in -charge. Item
whould include all pattern as design and
all matching colour fill /grouting. Item including repair of base lean concrete
and protection to the flooring after laying
97.20 Sqm
8
Contractor Asstt.Genl.Manager(Engg)
in the form of POP or plastic covering
would also have to be ensured.
33 178 Providing and laying polished vitrified
floor tiles in different sizes
(60cmX60cm) thickness to be specified
by the manufacturer ) with water absorptions less then 0.08% and
conferming to IS 15622 of approved
make in all colours and sheds laid on 20 mm thick cement mortar 1:4 (1 cement 4
coarse sand) including grouting the
joints with white cement and matching
pigments etc., complete.
1900.03 Sqm
12.2
34 12.47.2 188 Providing and laying pressed clay tiles
(as per approved pattern 20 mm proofing
compound laid over a bed of 20 mm
thick cement mortar 1:4 (1 cement : 4 coarse sand) mixex with finished neat
complete. nominal thickness and of
approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse
sand) mixed with 2% integral water
proofing compound laid over abed of 20mm thick cement morter 1:4 ( 1
cement:4 coarse sand)
114.00 Sqm
35 13.4.1 Providing & fixing UV stabilised 2mm
thick flat fibreglass reinforced plastic sheet roofing upto any pitch including
fixing with polymer coated 'J' or 'L'
hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but
excluding the cost of purlins, rafters,
trusses etc. The sheets shall be
manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3%
Ultra-violet stabiliser in resin system
under approximately 2400 psi and hot cured. They shall be of uniform
pigmentation and thickness without air
pockets and shall conform to IS 10192
and IS 12866.The sheets shall be opaque or translucent, clear or pigmented,
textured or smooth as specified.
216.00 Sqm
36. 13.5.2 201 12mm cement plaster of mix : 1:4 (1 Cement : 4 course sand)
2391.68 Sqm
37. 13.16.1 201 15 mm cement plaster on rough side of
single or half brick wall of mix (1
Cement : 6 course sand)
2745.11 Sqm
38. 13.19.1 202 6mm cement plaster of mix :1: 3 (1
Cement : 3 fine sand) 2908.91 Sqm
39. 13.26 202 Rough cast plaster upto 10 m height 115.20 Sqm
9
Contractor Asstt.Genl.Manager(Engg)
above ground level with a mixture of
sand and gravel or crushed stone from 6mm to 10mm nominal size dashed over
and including the fresh plaster in two
layers, under layer 12mm cement plaster
1:4 ( 1 cement : 4 coarse sand ) and top layer 10mm cement plaster 1:3 ( 1
cement : 3 fine sand ) mixed with 10%
finely grounded hydrated lime by volume of cement. Ordinary cement
finish using ordinary cement.
40. 13.41.1 204 Providing and applying plaster of paris
putty of 2 mm thickness over plastered surface to prepare the surface even and
smooth complete
5229.50 Sqm
41. MR 204 Distempering with oil bound washable distemper of approved brand and
manufacture to give an even shade new
work in two or more coat including a
coat of a cement primer.
5229.50 Sqm
42. 13.61.1 Providing and applying SPECTRUM
GRANITO NATURALA or equivalent
ready mixed/ready to use synthetic decorative textured coat of natural
coloured stone finish of approved
manufactured of average 2mm to 2.5mm
thickness of approved colours over external plastered surface (plaster to be
paid for saparately ) to perfect line, level,
plumb including finishing with sharp edge at corners, nitched etc., as per
manufactures specifications including all
labours, materials scaffoloding and surface preparations etc., for all lifts
complete as specified and directed by the
Engineer-in-charge.
515.20 Sqm
43. 22.7.1 206 Painting with synthetic enamel paint of approved brand and manufacture of
required colour to give an even
shade:Two or more coats on new work
19.80 Sqm
44 347 Providing and laying integral cement based water proofing treatment including
preparation of surface as required for
treatment of roofs, balconies, terraces etc consisting of following operations. (a)
Applying and grouting a slurry coat of
neat cement using 2.75 kg/sqm. of cement admixed with proprietary water
proofing compound conforming to IS.
2645 over the RCC slab including
cleaning the surface before treatment. (b) Laying cement concrete using broken
bricks/brick bats 25 mm to 100mm size
10
Contractor Asstt.Genl.Manager(Engg)
with 50% of cement mortar 1:5 (1
cement : 5 coarse sand) admixed with proprietary water proofing compound
conforming to IS : 2645 over 20 mm
thick layer of cement mortar of mix 1:5
(1 cement :5 coarse sand ) admixed with proprietary water proofing compound
conforming to IS : 2645 to required slope
and treating similarly the adjoining walls upto 300 mm height including rounding
of junctions of walls and slabs.
(c) After two days of proper curing
applying a second coat of cement slurry admixed with proprietary water proofing
compound conforming to IS : 2645. (d)
Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1
Cement : 4 Coarse sand ) admixed with
water proofing compounding conforming to IS : 2645 and approved by Engineer-
in-charge including laying glass fibre
cloth type II grade - I tissue reinforced of
approved quality in top layer of plaster and finally finishing the surface with
trowel with neat cement slurry and
making pattern of 300x300 mm square 3mm deep. e) The whole terrace so
finished shall be flooded with water for a
minimum period of two weeks for curing and for final test. All above operations to
be done in order and as directed and
specified by the Engineer-in-Charge :(
with five years servicegurantee)with average thickness of 120mm and
minimum thickness at khurra as 65 mm.
2552.00 Sqm
45 21.1.2 Providing and fixing aluminium work for doors, windows, ventilators and
partitions with extruded built up standard
tubular sections/ appropriate Z sections
and other sections of approved make conforming to IS: 733 and IS : 1285,
fixed with rawl plugs and screws or with
fixing clips, or with expansion hold fasteners including necessary filling up
of gaps at junctions, at top, bottom and
sides with required PVC/neoprene felt
etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed
mechanically wherever required
including cleat angle, Aluminium snap beading for glazing / panelling, C.P.
brass / stainless steel screws, all
complete as per architectural drawings
11
Contractor Asstt.Genl.Manager(Engg)
and the directions of Engineer-in-charge.
(Glazing and panelling to be paid for separately) :
A 21.2.1.
2
for fixed portion 3006.20 Kg.
B For shutters of doors, windows &
ventilators including providing and
fixing hinges/ pivots/bearing and making provision for fixing of fittings wherever
required including the cost of PVC /
neoprene gasket required (Fittings shall
be paid for separately).Anodised aluminium (anodised transparent or dyed
to required shade according to IS: 1868,
Minimum anodic coating of grade AC 15)
1038.59 Kg.
46. 21.3.2 Providing and fixing glazing in
aluminium door, window, ventilator
shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the
architectural drawings and the directions
of engineer-in-charge . (Cost of aluminium snap beading shall be paid in
basic item) :
A 21.3.3 With float glass panes of 5.50 mm
thickness 429.20 Sqm
B 21.2.2 With float glass panes of 8 mm thickness 14.40 Sqm
47. MR Providing and fixing 12mm thick Pre-laminated particle board with decorative
lamination on both sides flat pressed
three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll,
in panelling fixed in aluminium doors,
windows shutters and partition frames with C.P. brass / stainless steel screws
etc. complete as per architectural
drawings and directions of engineer-in-
charge.
266.21 Sqm
48. 9.1.1 Providing and fixing 7mm thk.
Aluminium grills of approved quality ,
make in required pattern for windows & ventilators openings with required
Aluminium F & H channel sectionto be
fitted in aluminium pipe
framework.(frame work shall be paid for separately) etc. all complete.
157.32 Sqm
49. 9.21.1 Providing wood work in frames of doors,
windows, clerestory windows and other frames, wrought framed and fixed in
position :second class teak wood
0.99 Cum
50. 9.23 Providing and fixing ISI marked flush 45.99 Sqm
12
Contractor Asstt.Genl.Manager(Engg)
door shutters conforming to IS: 2202
(Part I) non-decorative type, core of block board construction with frame of
1st class hard wood and well matched
commercial 3 ply veneering with vertical
grains or cross bands and face veneers on both faces of shutters :35 mm thick
including ISI marked Stainless Steel butt
hinges with necessary screws.
51. 9.127.2 Extra for providing lipping with 2nd
class teak wood battens 25 mm minimum
depth on all edges of shutters (over all
area of door shutter to be measured)
43.47 Sqm
52. 9.122.2 Providing & Fixing 1mm thick
decorative high pressure laminated sheet
of plain / wood grain in gloss / matt / suede finish with high density protective
surface layer and reverse side of
adhesive bonding quality conforming to
IS : 2046 Type S including cost of adhesive of approved quality.
89.46 Sqm
53. 21.4.1 30mm thick fibreglass reinforced plastic
(F.R.P.) flush door shutter in different plain and wood finish made with fire
retardant grade unsaturated polyester
resin, moulded to 3mm thick FRP
laminate all around, with suitable wooden blocks inside at required places
for fixing of fittings and polyurethane
foam (PUF) / Polystyrene foam to be used as filler material throughout the
hollow panel, casted monolithically with
testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856 :
2000, complete as per direction of
Engineer-in-charge.
31.50 Sqm
54. 21.12.1 Providing and fixing double action hydraulic floor spring of approved brand
and manufacture IS : 6315 marked, for
doors including cost of cutting floors as required, embedding in floors and cover
plates with brass pivot and single piece
M.S. sheet outer box with slide plate etc.
complete as per the direction of Engineer-in-charge.withsatinless steel
plate.
6.00 Each
55. 9.84 Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm
thick & 2100 mm long with SS screws
etc .complete as per direction of
Engineer-in-Charge.Anodized (AC 15 ) aluminium tubular handle bar
12.00 Each
13
Contractor Asstt.Genl.Manager(Engg)
56. 9.88 Providing and fixing IS : 3564 marked
aluminium extruded section body tubular type universal hydraulic door closer with
double speed adjustment with necessary
accessories and screws etc. complete.
55.00 Each
57. 21.13 Providing and fixing chromium plated brass 100 mm mortice latch and lock
with 6 levers and a pair of lever handles
with necessary screws etc. complete (best make of approved quality).
19.00 Each
58. 21.16.1 Providing and fixing 100mm brass locks
(best make of approved quality) for
aluminium doors including necessary cutting and making good etc. complete.
36.00 Each
59. 9.92.2 Providing fixing aluminium Anodic
Coating 15micron round shape handle of outer dia 100mm with SS screws etc.
Complete as per direction of Engineer-
in-charge
72.00 Each
60. Providing and fixing chromium plated brass handles with necessary screws etc.
complete: 100 mm
40.00 Each
61. 9.74.3 Providing and fixing bright finished
brass tower bolts (barrel type) with necessary screws etc. complete :
A. 9.74.4 150x10 mm 40.00 Each
B. 12.45.1 100x10 mm 20.00 Each
62. 193 Providing and fixing at all hight false
ceiling including providing fixing of
frame of special sections power pressed from M.S.sheet and galvanised in
accordance with zinc coating of grade
350 as per IS:277 and consisting of angle
cleats of size 25 mm wide x 1.6 mm thick with flanges of 22 mm and 37 mm
at 1200mm center to center one flange
fix to the celling with dash fastener 12.5mm dia X 40mm long with 6mm dia
bolts to the angle hangers of 25 X 25 X
0.55 mm of requried length and other
end of angle hanger beening fixed with nut & bolts to G.I channels 45 X15 X 0.9
mm running at the rate of 1200mm
center to center to which the celling section 0.5mm thick button wedge of
50mm with tapered flanges 26mm each
having clips of 10.5mm at for 50mm center to center shall be fixed in a
direction perpendicular to G.I. channel
with connecting clips made out of
2.64mm dia by 230mm long,
14
Contractor Asstt.Genl.Manager(Engg)
G.I. wire at every junction including
fixing the gypsum board with celling section and permetir channels 0.5mm
thick 27mm high having flanges of
20mm and 30mm long ,the permetir of
ceilling fixed to wallpartition with the help of rawal plugs at 450mm center to
center with 25mm long drive all screws
@ 230mm interval including jointing and fixing to a flush finish of tapered and
square edges of the board with
recommended filler, jointing tapes, finisher,& two coats of primer sutable
for board as per manufactures
specification and also including the cost
of making opening for light fitting , grills, outcuts made with frame of
perimeter channels suitbly fixed all
complete as per drawing and specification and dirction of the engineer
incharge but excluding the cost of
painting with:
12.5mm thick tapered edge gypsum board conferming to IS : 2095 - Part 1
1915.07 Sqm
(WATER SUPPLY AND SANITARY)
63. 12.41.1 192 Providing and fixing on wall face
unplasticised - Rigid PVC rain water
pipes conforming to IS : 13592 Type A
including jointing with seal ring
conforming to IS : 5382 leaving 10 mm
gap for thermal expansion. (i) Single
socketed pipes
A. 12.41.2 75 mm diameter 100.00 Rmt
B. 12.42 110 mm diameter 200.00 Rmt
64. 192 Providing and fixing on wall face
unplasticised - PVC moulded
fittings/accessories for unplasticised - Rigid PVC rain water pipes conforming
to IS : 13592 Type A including jointing
with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal
expansion
I Coupler
A 75 mm 20.00 Each
15
Contractor Asstt.Genl.Manager(Engg)
B 110 mm 40.00 Each
II Single Pushfit Coupler
A 75 mm 30.00 Each
B 110 mm 40.00 Each
III Single tee with door
A 75 X 75 X 75 mm 20.00 Each
B 110 X 110 X 110 mm 40.00 Each
IV Single tee without door
A 75 X 75 X 75 mm 20.00 Each
B 110 X 110 X 110 mm 30.00 Each
V Bend 87.5°
A 75 mm 20.00 Each
B 110 mm 30.00 Each
VI Shoe (Plain)
A 75 mm 20.00 Each
B 12.43 110 mm 30.00 Each
65. 192 Providing and fixing unplasticised -PVC
pipe clips of approved design to
unplasticised - PVC rain water pipes by
means of 50x50x50mm hard wood
plugs, screwed with M.S. screws of
required length including cutting brick
work and fixing in cement mortar 1:4 (1
cement : 4 coarse sand) and making good
the wall etc. complete.
A. 75 mm 150.00 Each
B. 17.1.1 110 mm 250.00 Each
66. 263 Providing and fixing water closet
squatting pan ( Indian type W.C. pan )
with 100mm sand cast Iron P or S trap,
10 litre low level white P.V.C. flushing
cistern with manually controlled device
(handle lever) conforming to IS : 7231,
Parryware/Hindware/Seabird/Orient
(Coral) with all fittings and fixtures
16
Contractor Asstt.Genl.Manager(Engg)
complete including cutting and making
good the walls and floors wherever
required.
17.2.1 White Vitreous china Orissa pattern
W.C. pan.of size 580x440mm with
integral type foot rests
9.00 Each
67. 263 Providing and fixing white vitreous
china pedestal type water closet
(European type W.C. pan) with seat and
lid, 10 litre low level white P.V.C.
flushing cistern with manually controlled
device (handle lever), conforming to IS :
7231, Parryware/Hindware/Seabrid
/Orient (Coral) with all fittings and
fixtures complete including cutting and
making good the walls and floors
wherever required :
17.7.2 W.C. pan with ISI marked white solid
plastic seat and lid
9.00 Each
68. 264 Providing and fixing wash basin with
C.I. brackets, 15 mm C.P. brass pillar
taps, 32 mm C.P. brass waste of standard
pattern, including painting of fittings and
brackets, cutting and making good the
walls wherever require :
17.23 White Vitreous chinaWash basin size
630x450 mm with a single 15 mm C.P.
brass pillar tap
14.00 Each
69. 17.9.1 267 Providing and fixing white vitreous
china flat back or wall corner type lipped
front urinal basin of 430x260x350mm
and 340x410x265mm sizes respectively.
18.00 Each
70. 265 Providing and fixing kitchen sink with
C.I. brackets, C.P. brass chain with
rubber plug, 40 mm C.P. brass waste
17
Contractor Asstt.Genl.Manager(Engg)
complete, includ-ing painting the fittings
and brackets, cutting and making good
the walls wherever required.
17.10.1
.1
White glazed fire clay kitchen sink of
size 600x450x250 mm
2.00 Each
71. 265 Providing and fixing Stainless Steel A
ISI 304 (18/8) kitchen sink as per I.S.
13983 with C.I. brackets and stainless
steel plug 40 mm including painting of
fittings and brackets, cutting and making
good the walls wherever required :
17.28.1 Kitchen sink with drain board
510x1040mm bowl depth 178mm
2.00 Each
72. 267 Providing and fixing P.V.C. waste pipe
for sink or wash basin including P.V.C.
waste fittings complete.
Flexible pipe
A 32 mm dia 14.00 Each
B 17.31 40 mm dia 3.00 Each
73. 17.33 267 Providing and fixing 600x450mm
bevelled edge mirror of superior glass (of
approved quality) complete with 6mm
thick hard board ground fixed to wooden
cleats with C.P. brass screws and
washers complete.
14.00 Each
74. 18.1 268 Providing and fixing 600x120x5mm
glass shelf with edges round of supported
on anodised aluminium angle frame with
C.P. brass brackets and guard rail
complete fixed with 40mm long
screws,rawl plugs etc., complete
14.00 Each
75. 292 Providing and fixing G.I. pipes complete
with G.I. fittings and clamps,including
cutting and making good the walls etc.
(internal work)
18
Contractor Asstt.Genl.Manager(Engg)
Exposed on wall
A 25mm dia. nominal bore 200.00 Rmt.
B 32mm dia. nominal bore 150.00 Rmt.
C 40mm dia. nominal bore 100.00 Rmt.
D 18.8.2 50mm dia. nominal bore 75.00 Rmt.
76. 18.13.1 292 Providing and fixing Chlorinated
Polyvinyl Chloride (CPVC) pipes,
having thermal stability for hot & cold
water supply including all CPVC plain &
brass threaded fittings i/c fixing the pipe
with clamps at 1.00 m spacing. This
includes jointing of pipes & fittings with
one step CPVC solvent cement and the
cost of cutting chases and making good
the same including testing of joints
complete as per direction of Engineer in
Charge. Concealed work including
cutting chases and making good the
walls etc., 20mm dia. nominal bore
250.00 Rmt.
77. 293 Making connection of G.I. distribution
branch with G.I.main of following sizes
by providing and fixing tee,including
cutting and threading the pipe etc.
complete.25 to 40 mm nominal bore
5.00 Each
78. 18.19.1 Providing and fixing gun metal gate
valve with C.I. wheel of
approvedquality(screwed end )
A 18.19.2 293 25 mm nominal bore (Horizontal) 6.00 Each
B 18.18.1 293 32 mm nominal bore. (Vertical) 4.00 Each
79. 18.22.1 293 Providing and fixing ball valve (brass) of
approved quality complete High or low
pressure with plastic floats 15 mm
nominal bore
4.00 Each
80. 294 Providing and fixing C.P. brass shower
rose with 15 or 20mm inlet
19
Contractor Asstt.Genl.Manager(Engg)
18.48 100mm diameter 3.00 Each
81. 18.49.1 300 Providing and placing on terrace (at all
floor levels) polyethylene water storage
tank ISI : 12701 marked indicating the
BIS License No. with cover and suitable
locking arrangement and making
necessary holes for inlet, outlet and
overflow pipes but without fittings and
the base support for tank
12000.00 Ltr.
82. 18.52.1 300 Providing and fixing C.P. brass bib cock
of approved quality conforming to
IS:8931 a) 15 mm nominal bore
30.00 Each
83. 17.71 300 Providing and fixing C.P. brass stop
cock (concealed) of standard design and
of approved make conforming to
IS:8931a) 15 mm nominal bore
15.00 Each
84. 17.72 274 Providing and fixing PTMT liquid soap
container 109mm wide, 125mm high and
112mm distance from wall of standard
shape with bracket of the same materials
with snap fittings of approved quality
colour and make, weighing not less than
105gms.
12.00 Each
85. 17.73 274 Providing and fixing PTMT towel ring
trapezoidal shape 215mm long, 200mm
wide with a minimum distances of 37mm
from wall face with concealed fittings
arrangement of approved quality, colour
and make weighing not less than 88 gms
12.00 Each
86. 17.76 274 Providing and fixing PTMT towel rail
complete with brackets fixed to wooden
cleats with CP brass screws with
concealed fitting arrangement of
approved quality and colour 600mm long
towel rail with total length of 645mm,
12.00 Each
20
Contractor Asstt.Genl.Manager(Engg)
width 78mm and effective height of
88mm, weighing not less than 190gms.
87. 18.65 275 Providing and fixing PTMT urinal cock
of approved quality and colour15 mm
nominal size 80 mm long, 44 mm high
and 30 mm wide with BSP female
threads weighing not less than 50gms
(Prayag or equivalent)
15.00 Each
88. 18.74.2 303 Providing and fixing PTMT Soap Dish
Holder having length of 138 mm,
breadth 102 mm, height of 75 mm with
concealed fitting arrangements, weighing
not less than 106gms.
12.00 Each
89. 18.53 301 Providing and fixing unplastiised P.V.C.
connection pipe with PTMTNuts of
approved quality, colour and make
(Prayag or equivalent)
14.00 Each
90. 305 Providing and fixing C.P. brass angle
valve for basin mixer and gyser points of
approved quality conforming to
IS:8931a) 15 mm nominal bore
14.00 Each
II CIVIL WORK + WATER
SUPPLY+SANITARY
2.8.1 Drainage work
91. 19.6.3 64 Earth work in excavation in foundation
trenches or drains (not exceeding 1.5 m
in width or 10 sqm on plan) including
dressing of sides and ramming of
bottoms, lift upto 1.5 m, including
getting out the excavated soil and
disposal of surplus excavated soil. All
kinds of soil.
836.64 Cum
92 Providing and laying non-pressure NP2
class (light duty) R.C.C. pipes with
collars jointed with stiff mixture of
375.00 Rmt.
21
Contractor Asstt.Genl.Manager(Engg)
cement mortar in the proportion of 1:2 (1
cement : 2 fine sand) including testing of
joints etc. complete :250 mm dia. R.C.C.
pipe
93. 19.7.1.
1
317 Constructing brick masonry manhole in
cement mortar 1:4 ( 1 cement : 4 coarse
sand ) R.C.C. top slab with 1:2:4 mix (1
cement : 2 coarse sand : 4 graded stone
aggregate 20mm nominal size),
foundation concrete 1:4:8 mix (1 cement
: 4 coarse sand : 8 graded stone
aggregate 40mm nominal size) inside
plastering 12mm thick with cement
mortar 1:3 (1 cement : 3 coarse sand)
finished with floating coat of neat
cement and making channels in cement
concrete 1:2:4 (1 cement : 2 coarse sand :
4 graded stone aggregate 20mm nominal
size) finished with a floating coat of neat
cement complete as per standard design:
A 19.7.3.
1
317 Inside size 90x80cm and 45cm deep
including C.I. cover with frame (light
duty) 455x610mm internal diamensions
total weight of cover and frame to be not
less than 38kg (weight of cover 23kg and
weight of frame 15 kg)With F.P.S. bricks
with class designation 35
15.00 Each
B 19.8.1.
1
317 Inside size 120x90cm and 90cm deep
including C.I. cover with frame (medium
duty) 500mm internal diameter, total
weight of cover and frame to be not less
than 116 kg (weight of cover 58 kg and
weight of frame 58 kg)With F.P.S. bricks
class designation 35
5.00 Each
C 317 Extra for depth for manholes
22
Contractor Asstt.Genl.Manager(Engg)
Size 90x80cm With F.P.S. bricks class
designation 35
2.00 Rmt.
III Surface Drain
4.1.4
94. 6.1.2 79 Providing and laying in position cement
concrete of specified grade excluding the
cost of centering and shuttering - All
work upto plinth level. :1:2:4 (1
cement:2 coarse sand : 4 geaded stone
aggregate 40 mm nominal size)
49.15 Cum
95. 13.4.1 99 Brick work with F.P.S. bricks of class
designation 35 in foundation and plinth
in :Cement mortar 1:6 (1 cement : 6
Coarse sand)
138.00 Cum
96. 5.18.1 15 mm cement plaster on rough side of
single or half brick wall finished with a
floating coat of neat cement of mix
:13.4.1 1:4 (1 Cement : 4 course
sand)
956.56 Sqm
97. Providing precast cement concrete Jali
1:2:4 (1 cement : 2 coarse sand : 4
graded stone aggregate 6mm nominal
size) reinforced with 1.6 mm dia mild
steel wire including centring and
shuttering, roughening cleaning, fixing
and finishing in cement mortar 1:3 (1
cement: 3 fine sand) etc. complete
excluding plastering of the jambs, sills
and soffits. 50mm thick
400.00 Sqm
IV
18.12.8 External water supply
98 Providing and fixing G.I. pipes complete
with G.I. fittings including trenching and
refilling etc. (external work)
23
Contractor Asstt.Genl.Manager(Engg)
A 80mm dia. nominal bore 706.00 Rmt.
B 18.13.2 50mm dia. nominal bore 203.00 Rmt.
99. 293 Making connection of G.I. distribution
branch with G.I.main of following sizes
by providing and fixing tee,including
cutting and threading the pipe etc.
complete.50 to 80 mm nominal bore
15.00 Each
100. 18.19.4 Providing and fixing gun metal non-
return valve of approved
quality(screwed end )
A 18.19.6 294 '50mm nominal bore 7.00 Each
B 294 '80mm nominal bore 2.00 Each
V
Sump (U G Tank)
13.4.1
101. 5.9.2 15 mm cement plaster on rough side of
single or half brick wall finished with a
floating coat of neat cement of mix : 1:4
(1 Cement : 4 course sand)
76.56 Sqm
102. Centring and shuttering including
strutting, propping etc. and removal of
form work for : Walls (any thickness)
including attached pilasters, buttresses,
plinth beams and string courses etc in
plinth level
76.56 Sqm
VI
Septik Tank
13.16
103. 202 6mm cement plaster of mix :1:3(1
cement:3 fine sand)
71.09 Sqm
19.18.1
24
Contractor Asstt.Genl.Manager(Engg)
104. 320 Supplying and fixing C.I. cover without
frame for manholes:
19.32.1 455x610 mm rectangular C.I. cover
(light duty) the weight of the cover to be
not less than 23 kg.
2.00 Nos.
105. 13.9.1 Making soak pit 2.5 m diameter 3.0
metre deep with 45 x 45 cm dry brick
honey comb shaft with bricks of class
designation35 and S.W.drain pipe 100
mm diameter, 1.8 m long complete as
per standard design With FPS bricks
1.00 No.
106. 13.16.1 201 12 mm cement plaster 1:3 (1 cement : 3
coarse sand) finished with a floating coat
of neat cement.
39.51 Sqm
107. 13.5.1 202 6 mm cement plaster 1:3 (1 cement : 3
fine sand) finished with a floating coat of
neat cement and thick coat of Lime wash
on top of walls when dry for bearing of
R.C.C. slabs and beams.
12.00 Sqm
108. 201 15 mm cement plaster on rough side of
single or half brick wall of mix 1:4(1
cement: 4 coarse sand)
59.73 Sqm
14.42.1
109. 13.62.1 219 White washing with lime to give an even
shade.Two or more coats
111.24 Sqm
110. 206 Painting with synthetic enamel paint of
approved brand and manufacture of
required colour to give an even shade:
Two or more coats on new work over
and under coat of suitable shade with
ordinary paint of approved brand and
manufacture.
7.92 Sqm
VIII
25
Contractor Asstt.Genl.Manager(Engg)
Landscaping
23.3.
111. 23.7 354 Supplying and stacking sludge at site
including royalty and carri-age upto 1
km ( sludge measured in stacks will be
reduced by 8% for payment).
375.00 Cum
112. 23.10.3 354 Fine dressing the ground 2500.00 100 Sqm
113. 354 Grassing with ‘Doob’ grass includ-ing
watering and maintenance of the lawn
for 30 days or more till the grass forms a
thick lawn free from weeds and fit for
mowing including supplying good earth
if needed (the good earth shall be paid
for separately).
In rows 5 cm apart in either direction. 2500.00 100 Sqm
IX
Internal Road work & pavement
16.1
114. 16.3.10
+ 2.25
16.1 Preparation and Consolidation of sub
grade with power road roller of 8 to 12
tonne capacity after excavating earth to
an average of 22.5 cm depth, dressing to
camber and consolidating with road
roller including making good the
undulations etc. and rerolling the
subgrade and disposal of surplus earth
lead upto 50 metres
1950.00 Sqm
115. Supplying and filling sand in
trenches,plinth,sides of foundation etc. in
layers not exceeding 20cm in depth
cosolidating each deposited layer by
watering, ramming consolidating and
dressing etc. complete
585.00 Cum
116. 16.4 Providing & laying in position cement 195.00 Cum
26
Contractor Asstt.Genl.Manager(Engg)
concrete of specified grade excluding the
cost of centring & shuttering -All work
upto plinth level (1 cement:5 coarse sand
:10 graded stone agg. 40mm nominal
size
117. Providing & laying design mix cement
conc. In roads,taxi tracks
&runways,having a minimum works test
beam flextural strength of 30 kg per cm
sq at 20 days usinng not less than 340 kg
of cement /cum of finished conc., coarse
sand & graded stone agg. of 40mm
nominal size in aproproate proportion as
per specified design criteria approved by
Engeener-in charge, mechanically
vibrated using needle & surface vibraters
in steel form works with sturdy MS
channel sections including curing &
providing & filling construction joints &
dummy joints with approved joint filler
& primer i/c rounding of the edges &
filling the groves 10@25mm deep at top
for constuction joints & 10mmx50mm
deep at top for dummy joints with joint
sealing compound( confirming to grade-
B of 1834 ) i/c making necessary
arrangements for expanstion joints etc all
complete
390.00 Cum
27
Contractor Asstt.Genl.Manager(Engg)
Name of work : Providing Internal Electrical Installation to R.O./D.O. office building at Raipur (C.G.)
SECTION B – Electrical Works
SCHEDULE OF QUANTITIES FOR INTERNAL ELECTRICAL WORK FOR FCI RAIPUR
S.No. Description of Item Unit QTY RATE AMOUNT
POINT WIRING
1
Point Wiring in PVC conduit, with modular type switch:
Wiring for light point / fanpoint /exhaust fan point / call bell point
with 1.5 sqm mm FR PVC insulated, copper conductor single core
cable in surface / recessed pvc conduit with modular switch, modular plate, suitable G.I. box and earthing the point with 1.5 sq mm FR.
PVC insulated, copper conductor single core cable etc as required.
Group –C
Each
518
2 Twin control Point Wiring in PVC conduit, with modular type
switch:
Wiring for light point / fanpoint /exhaust fan point / call bell point with 1.5 sqm mm FR PVC insulated , copper conductor single core
cable in surface / recessed pvc conduit with two way modular
switch, modular plate, suitable G.I. box and earthing the point with
1.5 sq mm FR. PVC insulated, copper conductor single core cable etc as required. (For2 no stairs.)
each 6
3 Power plug wiring in PVC conduit ( 2x4sqmm )
Wiring for light / power plug point with 2x4 sqm mm FR PVC insulated, copper conductor single core cable in surface / recessed
pvc conduit with 1 no x4 sq mm FR. PVC insulated, copper
conductor single core cable etc as required.
Mtr 237
4 Power plug wiring in PVC conduit (4x4sqmm )
Wiring for light / power plug point with 4 x 4 sq.mm FR PVC insulated, copper conductor single core cable in surface / recessed
pvc conduit with 2 no x 4 sq mm FR. PVC insulated, copper
conductor single core cable etc as required.
Mtr 397
5 Circuit / submain wiring in PVC conduit
28
Contractor Asstt.Genl.Manager(Engg)
Wiring for circuit / submain wiring alongwith earth wire with the
following sizes of FR PVC insulated copper conductor single core cables in surface / recessed PVC conduit as required.
a 2 x2.5 Sqmm.+ 1x 2.5 Sqmm earth wire metre 351
b 4x2.5 Sqmm.+ 2 x 2.5 Sqmm earth wire metre 362
c 4 x 4 Sqmm. + 2 X 4 Sqmm earth wire metre 161
d 4 x 6 Sqmm. + 2 X 6 Sqmm earth wire metre 159
6 Telephone wiring in existing conduit
Supplying and drawing following pair, 0.5 Sqmm FR PVC Insulated
copper conductor,unarmoured telephone cable in surface/recessed PVC conduit as required.
2 Pair metre 531
4 Pair metre 149
7 S / F PVC conduit :
Supply and fixing following sizes of PVC conduit along with accessories in surface / recess including cutting the wall and making
good the same in case of recessed conduit as required.
20mm metre 531
25mm metre 963
32mm metre 352
8 S / F modular type switch / socket
Supply and fixing following modular type switch / socket on the
existing modular plate and switch box / cover including connection etc. as required.
a 5 / 6 amps swich each 127
b 2 way 5/ 6 amps swich each 6
c 15 / 16 amps swich each 467
d 3 pin 5 / 6 amps socket outlet each 260
e 6 pin 15 / 16 amps socket outlet each 75
f Telephone socket outlet each 64
9 S / F modular type electronic fan regulator
29
Contractor Asstt.Genl.Manager(Engg)
Supplying and fixing stepped type fan regulator on the existing
modular plate switch box including connections but excluding modular plate etc as required.
each 113
10 S / F modular type blanking plate
Supplying and fixing modular blanking plate on the existing
modular plate switch box including connections but excluding modular plate etc as required.
each 71
11 S / F modular boxes, base & cover plate
Supplying and fixing following size / modules, G.I. Box alongwith
modular base & cover plate for modular switches in recess etc
required.
a 1 or 2 Module (75mm X 75mm) each 48
b 8 Module ( 125x125 ) each 246
12 S / F power plug point modular type accessories
Supply and fixing suitable size size G.I. Box with modular plate and
cover in front on surface or in recess, including providing and fixing
6 pin 15 / 16 amps modular socket outlet and 15 / 16 amps modular switch, connection, etc. as required
each 63
13 S / F Ceiling rose :
Supplying and fixing 3 Pin, 5 amp. Ceiling rose on the existing junction box / wooden block including connection etc as required.
each 11
14 S / F brass holder :
Supplying and fixing brass batten / angle holder including
connection etc. as required. each 18
15 S / F TP MCB DB:
Supplying and fixing following way, three pole and neutral, sheet,
MCB distribution board, 415 volts, on surface / recess, complite with
tinned copper busbar, neutral busbar earth bar, din bar, detachable
gland plate interconnections phosphatized and powder painted including earthingetc as required ( But without
MCB/RCCB/ISOLATOR )
a 6 Way (4+18), Double door horizontal type each 5
b 8 Way (4+24), Double door horizontal type each 5
16 S / F Vertical type TP MCB DB:
30
Contractor Asstt.Genl.Manager(Engg)
Supplying, installation, testing, and commissioning of surface/ recess
mounting vertical type, 415 volts TPN MCB distribution board of
sheet steel, dust protected, duly phosphatized and power painted inclusive of 200 Amps tinned copper busbarnutral link, earth bar, din
bar for mounting MCB' s detachable gland/ knock out plate, and with
100 Amps 10 KA MCCB as incomer interconnection between incomer MCCB and busbars of following ways (but without MCB's
as required.)
12 Way with 100 Amps MCCB as incomer each 2
17 S / F "C" series SPMCB
Supplying and fixing 5 to 32 amps rating, 240 volts, 'C' series
miniature circuit breaker suitable for lighting and other loads of
following poles in the existing MCB DB complete with connections, testing and commissioning etc as required.
Single pole each 216
18 S / F TP MCB ISOLATOR
Supplying and fixing following rating, four pole, 215 volts, isolator
in the existing MCB DB complete with connections, testing and
commissioning etc as required.
40 Amp each 5
63 Amp each 5
19 S / F SPN RCCB
Supplying and fixing following rating, double pole,(single pole and
neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB
complete with connections, testing and commissioning etc. as
required.
25 Amp each 15
40 Amp each 15
20
Data cable cat-6 in existing conduit Mtr. 2047
21
Supply, eraction and testing of RJ - 45 Computer socket I.O with face plate and box for surface / concealed mounting system, complet
as required . D.Link Make NOS 242
22 Supply & installation of 2 modole PVC Box with plate (IN CAT 3 ROOM) for computer
NOS 96
31
Contractor Asstt.Genl.Manager(Engg)
23 Supply & installation of 8 modole PVC Box with plate (IN CAT 3
ROOM) for light socket with each computer NOS 201
24 Supply & laying of Telephone cable 20 pair 0.61 mm (armoured) Mt 260
25
Supplying and fixing of Krone type telephone tag block, suitable for
the multi-core telephone cable and shall accommodate tin-plated
phospher bronze connectors, providing economical and reliable spice. The connectors shall terminate both in incoming and outgoing
lines.The tag blocks shall be mounted inside fabricated 14
gaugeG.I.Box of suitable size with removable hinged covers and locking arrangement and shall be fully accessible. The item is
inclusive of providing and fixing of G.I boxes in surface/recessed
systems etc. as required complete.
a 50 Pair tag block No 2
b 20 Pair tag block No 5
26
Supply, Installation, Testing and Commissioning of 24 Cat-6 Patch /
jack panel with connectors, outlets and necessary connectivity
complete as required. No 2
27 a) Installation. Supply and proper dressing of 19" 12 U wall
mounting rack with front glass door No 3
28 Supplying and fixing following rating, four pole,415 volts, MCB in the existing MCB DB complete with connections, testing and
commissioning etc as required.
a 40 Amp each 5
b 63 Amp each 5