PARTS LIST

1 Radio Mount

1 Feed Tube

1 Antenna Reflector

1 AZ/EL Mount

1 Mast

2 Hose Clamps

2 Carriage Bolt .25 x 20

1 Hex Bolt .25-20 x 1.5"

3 Flange Nut .25-20

3 Flat Washers .25-20

1 Spacer

1 Carriage Bolt #10 x 1.25"

1 #10 Hex Nut

2 U Bolts 5/16

2 V-Bracket

4 Star Nut

1 Canopy Module Radio

QTY DESCRIPTION BACKHAUL MODULE SUBSCRIBER MODULE REFLECTOR (ONLY) with REFLECTOR (BHRF) with REFLECTOR (27RD)

RADIO MOUNT

CANOPY MODULERADIO

HOSE CLAMP(2 PLACES)

AZ/EL MOUNT

MAST U BOLT(2 PLACES)

V-BRACKET(2 PLACES)

SPACER

CARRIAGE BOLT #10 x 1.25"

HEX BOLT.25-20 x1.5"

FEED TUBE

FLANGE NUT.25-20

CARRIAGE BOLT.25 X 20(2 PLACES)

#10 HEX NUT

FLAT WASHER.25-20

FLANGE NUT.25-20(3 PLACES)

FLAT WASHER.25-20(3 PLACES)

STAR NUT(4 PLACES)

ANTENNA REFLECTOR

http://www.motorola.com/canopySales Support: 866-515-5825Technical Support: 888-605-2552 (+1 217 824 9742)

REFLECTOR ASSEMBLY and INSTALLATION27 RD REFLECTOR

Tools Needed: 7/16 inch wrench or adjustable wrench Flat blade screwdriver or 5/16 inch socket for hose clamps and ground screw 1/2 inch wrench for U-Bolts - Backhaul only 3/8" wrench for #10 nut

Tighten Hose Clamps securely so the Radio is snug to the mount with no gaps at the lower support rib.

4

Loosen and open hose clamps. Slide clamps through the two openings in the Radio above and below the mount as shown in this illustration. Close hose clamps attaching radio to mount.

3

Slide Radio into mount as shown.2

RADIO MOUNT

RADIO

Place Antenna Reflector on flat surface or table.Attach AZ/EL Mount to Reflector using Carriage Bolts, Flat Washers, and Flange Nuts. Tighten nuts securely.

1

RADIO

RADIOMOUNT

HOSE CLAMPS

CARRIAGEBOLT

FLAT WASHERFLANGE NUT

REFLECTOR

AZ/ELMOUNT

HOSECLAMP

9/04 ECN9000000 8000973-01

RADIOMOUNT

HOSE CLAMPADJUSTMENTSCREW(FACING RADIO)

Assemble the Feed Tube to the Reflector as shown with 1/4" Flange Nut, .81" Spacer, Flat Washer and 1-1/2" Hex Bolt. Tightenhardware securely. 6

1/4" HEX FLANGE NUT

SPACER

FLAT WASHER

1-1/2"HEX BOLT

7

Slide assembledradio and mountinto feed tube as shown.

Secure Radio Mount to Feed Tube with #10 x 1-1/4" Carriage Bolt and #10 Nut. Tighten Nut to snug the bottom of the tube up to the Mount.

#10 NUT

#10 x 1-1/4"CARRIAGEBOLT

8

9 Install Mast on tower or building. For Backhaul,use provided U-Bolts. For Subscriber Module, use locally approved fasteners (lag bolts, screws, etc.) depending on installation. Adjust Mast to be vertical and plumb.Tighten all hardware securely. Connect Ground Screw to Earth Ground using heavy guage (10AWG) copperwire. Refer to local or national electrical regulations for exact specifications.

BACKHAUL MOUNT SUBSCRIBER MOUNT

VER

TICA

L &

PLU

MB

LOCALLY APPROVED FASTENERS

U BOLT STARNUT

V-BRACKET

MAST

12ELEVATION

-20

-100

10 20

The Elevation is set by rotating the Reflector vertically while the Elevation Adjustment Hardware is loose.An elevation scale is located on the side of the AZ/EL Mount. As the Reflector is adjusted, the elevationscale depicts the elevation angle. Once the elevation is determined, tighten BOTH Elevation Ajustment Nuts to secure the required angle.

ELEVATION

-20

-100

10 20

ELEVATIONADJUSTMENTNUT (ONE ON EACH SIDE)

VER

TICA

L &

PLU

MB

UP TO 3.25" O.D.PIPE (8.0cm O.D.)

10 AWGGROUND WIRE

GREENGROUND SCREW

ALTERNATEGROUND SCREW HOLE

MAST

AZ/EL MOUNT

AZ/EL MOUNTCLAMP

Loosen bolts on AZ/EL Mount Clamp. Slide AZ/ELMount with preassembed Reflector over mast. Loosely tighten AZ/EL Mount Clamp.

10 11To adjust azimuth, move Reflector from side to side while AZ/EL Clamp Hardware is loose. Once azimuth is determined, tighten (2) AZ/EL Clamp Nuts securely.

AZ/ELCLAMP NUTS

REFLECTOR

ELEVATION

Read indicated elevation at this edge of plate. The Beam from the Reflector will be horizontal when the Mast is vertical and the plate is set at 4.5 degrees up-elevation as shown.

Place Feed Tube on a solid surface or table. The Reflector end of the Feed Tube has a large hole on the bottom side. Align bolt holes and press Reflector Socket completely onto Feed Tube as shown.

5

FEED TUBE

ANTENNA REFLECTOR