pb uddeholm vidar superior english

UDDEHOLM VIDAR SUPERIOR

SS-EN ISO 9001SS-EN ISO 14001

Edition 4, Revised 09.2013, not printedThe latest revised edition of this brochure is the English version,which is always published on our web site www.uddeholm.com

This information is based on our present state of knowledge and is intended to provide generalnotes on our products and their uses. It should not therefore be construed as a warranty ofspecific properties of the products described or a warranty for fitness for a particular purpose.

Classified according to EU Directive 1999/45/ECFor further information see our Material Safety Data Sheets.


Uddeholm Vidar Superior belongs to the new generation of modified H11

(1.2343) steel grades with a low silicon content. The steel is produced using

the very latest in production techniques and shows very high toughness

values.

Uddeholm Vidar Superior is tested and certified, providing the customer

the best possible performance. Suitable applications are those where a high

toughness is needed; like in die casting or forging. The high purity in Udde-

holm Vidar Superior makes it an excellent steel also in plastic applications.

VIDAR is a trade mark registered in the European Union.

UDDEHOLMS ABNo part of this publication may be reproduced or transmitted for commercial purposes

without permission of the copyright holder.

3UDDEHOLM VIDAR SUPERIOR

GeneralUddeholm Vidar Superior is a chromium-molybdenum-vanadium alloyed hot work toolsteel which is characterized by: High level of resistance to thermal shock and

thermal fatigue Good high-temperature strength Excellent toughness and ductility in all

directions Excellent through-hardening properties Good dimensional stability during hardening

Improved tooling performanceThe name Superior implies that by specialprocessing techniques and close processcontrol, the steel attains high purity and a veryfine structure. Uddeholm Vidar Superiorshows significant improvements in impacttoughness compared to material of the H11(W.-Nr. 1.2343) type.

The improved impact toughness is parti-cularly valuable for tooling subjected to highmechanical and thermal stresses, e.g. die castingdies and forging tools. In practical terms, toolsmay be used at somewhat higher workinghardness (2 HRC) without loss of toughness.Since increased service hardness limits theformation of thermal fatigue cracks, improvedtool performance can be expected.

Tools for hot forgingAustenitizing

Material temperature (approx.) HRC

Aluminium,magnesium 9801000C (17951830F) 4452Copper alloys 9801000C (17951830F) 4452Steel 9801000C (17951830F) 4050

Moulds for plasticsAustenitizing

Part temperature (approx.) HRC

Injection mouldsCompression/transfer moulds 9801000C (17951830F) 4652

Typical C Si Mn Cr Mo Vanalysis % 0.36 0.3 0.3 5.0 1.3 0.5

Standard X36 CrMoV5 (CNOMO)specification X36 CrMoV5-1, W.-Nr. 1.2340

~AISI H11, ~B H11, ~W.-Nr. 1.2343,~AFNOR Z38 CDV 5,~UNI X37 CrMoV 51 KU,~UNE X37 CrMoV 5

Deliverycondition Soft annealed to approx.180 HB

Colour code Red/orange with a white line across

ApplicationsTools for die casting

Aluminium-,Tin, lead, Magnesium

Part zinc alloys, HRC alloys, HRC

Dies 4650 4248Fixed inserts, cores 4852 4650Sprue parts (ORVAR) (ORVAR)Nozzles (ORVAR) (ORVAR)Ejector pins (nitrided) (ORVAR) (ORVAR)Plunger, shot-sleeve(normally nitrided) (ORVAR) (ORVAR)

Austenitizingtemperature 9801000C (17951830F)

PropertiesPhysical dataAll specimens are taken from the centre of a1000 x 200 mm (39,4" x 7,88") bar. Unlessotherwise is indicated all specimens werehardened from 1000C (1832F), quenched ina vacuum furnace and tempered 2 + 2h at600C (1110F) to 45 1 HRC.

Temperature 20C 200C 400C 600C(68F) (392F) (750F) (1010F)

Density,kg/m3 7 800 7 750 7 700 7 600lbs/in3 0.282 0.280 0.278 0.275

Modulusof elasticity

MPa 210 000 200 000 180 000 140 000psi 30.5 x 106 29.1 x 106 26.1 x 106 20.3 x 106

Coefficientof thermalexpansion

per Cfrom 20C 11.6 x 10-6 12.4 x 10-6 13.2 x 10-6

per Ffrom 68F 6.4 x 10-6 6.9 x 10-6 7.3 x 10-6

Thermalconductivity

W/m C 30 30 31Btu in/

(ft2hF) 211 211 218


EFFECT OF TIMEAT HIGH TEMPERATURES ON HARDNESS

Hardness, HRC50

45

40

35

30

25

EFFECT OF TESTING TEMPERATURESON IMPACT ENERGY

Charpy V specimens, short transversedirection.

Heat treatmentSoft annealingProtect the steel and heat through to 850C(1562F). Then cool in furnace at 10C (20F)per hour to 650C (1202F), then freely in air.

Stress relievingAfter rough machining the tool should beheated through to 650C (1202F), holdingtime 2 hours. Cool slowly to 500C (932F),then freely in air.

HardeningPreheating temperature: 600900C (11121652F). Minimum two preheating steps at600650C (11121202F) and 820850C(15081562F). When three preheats are usedthe second is carried out at 820C (1508F)and the third at 900C (1652F).Austenitizing temperature: 9801000C (17961832F).Soaking time: 3045 minutes.Soaking time = time at austenitizing tempera-ture after the tool is fully heated through.

Protect the tool against decarburization andoxidation during austenitizing.

ft. lbs

89

74

59

45

30

15

psi Rm, Rp0,21000x MPa

290 2000

261 1800

232 1600

203 1400

174 1200

145 1000

116 800

87 600

58 400

29 200

A5,Z %

100

90

80

70

60

50

40

30

20

10

APPROXIMATE STRENGTHAT ELEVATED TEMPERATURES

Longitudinal direction.

Impact energy, J

100 200 300 400 500 600 700C 210 390 570 750 930 1110 1290 F

Testing temperature

1 10 100 1000

Time, h

600C (1112F)

550C (1022F)

500C (932F)

Z

A5

RmRp0,2

120

100

80

60

40

20

40 20 20 100 200 300 400 500C

68 210 390 570 750 930F

Testing temperature

Mechanical propertiesApproximate tensile strength at room tem-perature.

Hardness 45 HRC 46.5 HRC 48.5 HRC

Tensilestrength

Rm 1450 MPa 1580 MPa 1680 MPa 210 000 psi 229 000 psi 244 000 psi

Yield strengthRp0,2 1240 MPa 1340 MPa 1410 MPa

180 000 psi 194 000 psi 204 000 psi

ElongationA5 13% 13% 12%

Reductionin area

Z 65% 65% 64%


Air cooling ofbars, mm

1 10 100 1 000 10 000 100 000 Seconds

1 10 100 1 000

1 10 100 Hours

0.2 1.5 10 90 600

Minutes

2000

1800

1600

1400

1200

1000

800

600

400

200

1100

1000

900

800

700

600

500

400

300

200

100

CF

CoolingCurveNo.

HardnessHV 10

800500(sec)

TCarbides

Austenitizing temperature 1000CHolding time 30 min.

Ms

Mf

987654321

Martensite

= 830CsA 1c

Pearlite

1

2

3

4

5

6

7

8

9

657

642

592

585

585

579

459

446

425

1

10

140

280

630

1030

5200

10400

20800

Bainite

fA 1c = 890C

CCT GRAPH

Austenitizing temperature 1000C (1832F). Holding time 30 minutes.

0.0079 0.059 0.394 3.54 23,6 inch

Quenching media High speed gas/circulating atmosphere.

Vacuum (high speed gas with sufficientpositive pressure). An interrupted quench at350450C (662842F) is recommendedwhere distortion control and quench crack-ing are a concern.

Martempering bath (salt or fluidized bed) at500550C (9321022F) or 180220C(356428F).

Warm oil, approx. 80C (176F).

Note 1: Temper the tool as soon as its tem-perature reaches 5070C (122158F).Note 2: In order to obtain the optimumproperties for the tool, the cooling rate shouldbe fast, but not at a level that gives excessivedistortion or cracks.


1234567890

1234567890

1234567890

1234567890

1234567890

1234567890

1234567890

1234567890

123456789

123456789

123456789

123456789

123456789

123456789

123456789

APPROXIMATE IMPACT ENERGY ATDIFFERENT TEMPERING TEMPERATURES

Charpy V specimens, short transversedirection.

200 400 450 500 550 600 625 650C 390 750 840 930 1020 1110 1155 1200F

Tempering temperature (2h + 2h)

ft.lb.

103

86

74

59

44

29

15

HARDNESS, GRAIN SIZE AND RETAINEDAUSTENITE AS A FUNCTION OF AUSTENITIZINGTEMPERATURE

Impact energy KV Joule 140

120

100

80

60

40

20

Retained austenite

TEMPERING GRAPH

Air cooling of specimen 15 x 15 x 40 mm (0.6" x 0.6" x 1.6").

Hardness, HRC Retained austenite %

60

55

50

45

40

35

30

25

20

Austenitizing temperature1000C (1832F)

TemperingChoose the tempering temperature accordingto the hardness required by reference to thetempering graph below. Temper minimumtwice with intermediate cooling to room

100 200 300 400 500 600 700C 212 392 572 752 932 1112 1292F

Tempering temperature (2 + 2h)

Austenitizing temperature980C (1796F)

8

6

4

2

970 990 1010 1030C 1778 1814 1850 1886F

Austenitizing temperature

56

55

54

53

52

51

50

Grain size

Retained austenite

40

35

30

25

20

15

10

5

Retained austenite, %

8

6

4

Hardness

Hardness, HRCGrain sizem

Above tempering curves are obtained after heat treatment of samples with a size of 15 x 15 x 40 mm,cooling in forced air. Lower hardness can be expected after heat treatment of tools and dies due tofactors like actual tool size and heat treatment parameters.

temperature. Holding time at temperature isminimum 2 hours. Tempering in the tempera-ture range 450550C (8401020F) for theintended final hardness will result in a lowertoughness.


Depth of nitriding

DepthProcess Time mm inch

Gas nitriding 10 h 0.12 0.0047at 510C (950F) 30 h 0.21 0.0082

Plasma nitriding 10 h 0.10 0.0039at 480C (895F) 30 h 0.19 0.0075

Nitrocarburizing in gas at 580C (1075F) 2.5 h 0.13 0.0051

in salt bath at 580C (1075F) 1 h 0.07 0.0028

1234567890

1234567890

1234567890

1234567890

1234567890

1234567890

1234567890

1234567890

Tempering in the temperature range 450550C (8401020F) for the intended finalhardness will result in a lower toughness.

Nitriding and nitrocarburizingNitriding and nitrocarburizing result in a hardsurface layer which is very resistant to wearand erosion. The nitrided layer is, however,brittle and my crack or spall when exposed tomechanical or thermal shock, the risk increas-ing with layer thickness. Before nitriding, thetool should be hardened and tempered at atemperature at least 50C (120F) above thenitriding temperature.

Dimensional changes duringhardening and temperingDuring hardening and tempering the die isexposed to thermal as well as transformationstresses. This will inevitably result in dimen-sional changes and in the work case distortion.It is therefore recommended to always leave amachining allowance after machining beforethe die is hardened and tempered. Normallythe size in the largest direction will shrink andthe size in the smallest direction might in-crease but this is also a matter of the die size,the die design as well as the cooling rate afterhardening.

For Uddeholm Vidar Superior it is recom-mended to leave a machining allowance of0.2 per cent of the dimension in length, widthand thickness.

Charpy U specimens, short transversedirection.

Impact energyJ/cm2

80

70

60

50

40

30

20

10

200 300 400 500 550 600C390 570 750 930 1020 1110 F

Tempering temperature (2h + 2h)

Nitriding in ammonia gas at 510C (950F) orplasma nitriding in 75% hydrogen / 25% nitro-gen at 480C (896F) both result in a surfacehardness of ~1100 HV0,2. In general, plasmanitriding is the preferred method because ofbetter control over nitrogen potential; in par-ticular, formation of the so-called white layer,which is not recommended for hot-workservice, can readily be avoided.

However, careful gas nitriding can give per-fectly acceptable results.

Uddeholm Vidar Superior can also be nitro-carburized in either gas or salt bath. The sur-face hardness after nitrocarburizing is 10001100 HV0.2.

* Depth of case = distance from surface where hardnessis 50 HV0.2 over base hardness

Uddeholm Vidar Superior can also be nitridedin the soft annealed condition. The hardnessand depth of case will, however, be reducedsomewhat in this case.


Cutting datarecommendationsThe cutting data below are to be consideredas guiding values which must be adapted toexisting local conditions. More information canbe found in the Uddeholm publication Cut-ting data recommendation.

The recommendations, in following tables,are valid for Uddeholm Vidar Superior in softannealed condition.

DrillingHIGH SPEED STEEL TWIST DRILL

Drill diameter Cutting Feed (f)speed (vc)

mm inch m/min f.p.m. mm/rev. i.p.r.

5 3/16 1520* 4966* 0.050.10 0.0020.004 510 3/163/8 1520* 4966* 0.100.20 0.0040.0081015 3/85/8 1520* 4966* 0.200.25 0.0080.0101520 5/83/4 1520* 4966* 0.250.30 0.0100.012

1) For coated HSS drill vc = 3540 m/min. (115131 f.p.m.)

CARBIDE DRILL

Type of drill

Cutting data Indexable Solid Carbideparameters insert carbide tip)

Cuttingspeed (vc)

m/min 200230 120150 120150f.p.m. 656755 394492 394492

Feed (f)mm/rev. 0.050.152) 0.100.253) 0.150.254)

i.p.r. 0.0020.0062) 0.0040.013) 0.0060.014)

1) Drill with replaceable or brazed carbide tip2) Feed rate for drill diameter 2040 mm (0.81.6)3) Feed rate for drill diameter 520 mm (0.20.8)4) Feed rate for drill diameter 1020 mm (0.40.8)

END MILLING

Type of milling

CarbideCutting data Solid indexableparameters carbide insert HSS

Cuttingspeed (vc)

m/min 145185 150190 30351)

f.p.m. 476607 492623 981151)

Feed (fz)mm/tooth 0.030.22) 0.080.22) 0.050.352)

inch/tooth 0.0010.0082) 0.0030.0082) 0.0020.0132)

Carbidedesignation

ISO P10P20 US C6C5

1) For coated HSS end mill vc = 5055 m/min. (164180 f.p.m.)2) Depending on radial depth of cut and cutter diameter

MillingFACE AND SQUARE SHOULDER MILLING

Milling with carbide

Cutting data parameters Rough milling Fine milling

Cutting speed (vc)m/min 140220 220260f.p.m. 459722 722853

Feed (fz)mm/tooth 0.20.4 0.10.2inch/tooth 0.0080.016 0.0040.008

Depth of cut (ap)mm 24 2inch 0.080.16 0.08

Carbide designationISO P20P40 P10US C6C5 C7

Coated Coatedcarbide carbide or

cermet

Turning

Turning with carbide TurningCutting data Rough Fine with HSS parameters turning turning Fine turning

Cuttingspeed (vc)

m/min 170220 220270 2530f.p.m. 558722 722886 8298

Feed (f)mm/rev. 0.20.4 0.050.2 0.3i.p.r. 0.0080.016 0.0020.008 0.012

Depthof cut (ap)

mm 24 0.52 2inch 0.080.16 0.020.08 0.08

Carbidedesignation

ISO P20P30 P10 US C6C5 C7

Coated Coated carbidecarbide or cermet

HSS = High Speed Steel


Photo-etchingUddeholm Vidar Superior is particularlysuitable for texturing by the photo-etchingmethod. Its high level of homogeneity and lowsulphur content ensures accurate and consist-ent pattern reproduction.

WeldingWelding of die components can be performed,with acceptable results, as long as the properprecautions are taken during the preparationof the joint, the filler material selection, thepreheating of the die, the controlled cooling ofthe die and the post weld heat treatmentprocesses. The following guidelines summarizethe most important welding process param-eters.

For more detailed information refer toUddeholms Welding of Tool Steel brochure.

Electrical DischargeMachiningEDMFollowing the EDM process, the applicable diesurfaces are covered with a resolidified layer(white layer) and a rehardened and untem-pered layer, both of which are very brittle andhence detrimental to die performance.

If EDM is used the white layer must becompletely removed mechanically by grindingor stoning. After the finish machining the toolshould also then be given an additional temperat approx. 25C (50F) below the highestprevious tempering temperature.

Further information is given in the Udde-holm brochure EDM of Tool Steel.

Welding method TIG MMA

Preheatingtemperature* Min. 325C (620F) Min. 325C (620F)

DIEVAR TIG-WELD UTP 673Filler metals QRO 90 TIG-WELD QRO 90 WELD

Maximuminterpass 475C 475Ctemperature (880F) (880F)

Post welding 2040C/h (3570F/h) for the firstcooling 23 hours and then freely in air.

Hardness 5558 HRC (673)after welding 4853 HRC 4853 HRC

Heat treatment after welding

Hardened Temper at 1020C (2040F) belowcondition the highest previous tempering tem-

perature.

Soft annealed Soft-anneal the material at 850Ccondition (1560F) in protected atmosphere.

Then cool in the furnace at 10C (20F)per hour to 650C (1200F) then freelyin air.

* Preheating temperature must be established throughout the die and must be maintained for the entirety of the welding process, to prevent weld cracking.

GrindingA general grinding wheel recommendation isgiven below. More information can be found inthe Uddeholm publication Grinding of ToolSteel.

WHEEL RECOMMENDATION

Soft annealed HardenedType of grinding condition condition

Face grindingstraight wheel A 46 HV A 46 HV

Face grindingsegments A 24 GV A 36 GV

Cylindrical grinding A 46 LV A 60 KV

Internal grinding A 46 JV A 60 IV

Profile grinding A 100 IV A 120 JV

Further informationPlease contact your local Uddeholm office forfurther information on the selection, heattreatment, application and availability of Udde-holm tool steel.

PolishingUddeholm Vidar Superior has good polisha-bility in the hardened and tempered conditionbecause of a very homogeneous structure.This coupled with a low level of non metallicinclusions, due to ESR process, ensures goodsurface finish after polishing.

Note: Each steel grade has an optimum polish-ing time which largely depends on hardnessand polishing technique. Overpolishing can leadto a poor surface finish, orange peel orpitting.

Further information is given in the Udde-holm publication Polishing of mould steel.

10


The ESR Tool Steel ProcessThe starting material for our tool steel is carefully se-lected from high quality recyclable steel. Together withferroalloys and slag formers, the recyclable steel is meltedin an electric arc furnace. The molten steel is then tappedinto a ladle.

The de-slagging unit removes oxygen-rich slag andafter the de-oxidation, alloying and heating of the steelbath are carried out in the ladle furnace. Vacuum de-gassing removes elements such as hydrogen, nitrogen andsulphur.

ESR PLANT

In uphill casting the prepared moulds are filled with acontrolled flow of molten steel from the ladle.

From this, the steel can go directly to our rolling millor to the forging press, but also to our ESR furnacewhere our most sophisticated steel grades are meltedonce again in an electro slag remelting process. This isdone by melting a consumable electrode immersed in anoverheated slag bath. Controlled solidification in the steelbath results in an ingot of high homogeneity, thereby

removing macro segregation. Melting under a protectiveatmosphere gives an even better steel cleanliness.

HOT WORKING

From the ESR plant, the steel goes to the rolling mill orto our forging press to be formed into round or flat bars.

Prior to delivery all of the different bar materials aresubjected to a heat treatment operation, either as softannealing or hardening and tempering. These operationsprovide the steel with the right balance between hard-ness and toughness.

MACHINING

Before the material is finished and put into stock, we alsorough machine the bar profiles to required size and exacttolerances. In the lathe machining of large dimensions, thesteel bar rotates against a stationary cutting tool. Inpeeling of smaller dimensions, the cutting tools revolvearound the bar.

To safeguard our quality and guarantee the integrity ofthe tool steel we perform both surface- and ultrasonicinspections on all bars. We then remove the bar ends andany defects found during the inspection.

ROLLING MILL

FORGING

ESR-PLANT

ELECTRIC ARCFURNACE

STOCK

HEAT

TREATMENT

UPHILL CASTING

MACHINING

www.assab.com www.uddeholm.com

Network of excellenceUDDEHOLM is present on every continent. This ensures you

high-quality Swedish tool steel and local support wherever you

are. ASSAB is our exclusive sales channel, representing Udde-

holm in the Asia pacific area. Together we secure our position

as the worlds leading supplier of tooling materials.

UD

DEH

OLM

R-130917

UDDEHOLM is the worlds leading supplier of tooling materials. This

is a position we have reached by improving our customers everyday

business. Long tradition combined with research and product develop-

ment equips Uddeholm to solve any tooling problem that may arise.

It is a challenging process, but the goal is clear to be your number one

partner and tool steel provider.

Our presence on every continent guarantees you the same high quality

wherever you are. ASSAB is our exclusive sales channel, representing

Uddeholm in the Asia pacific area. Together we secure our position

as the worlds leading supplier of tooling materials. We act worldwide,

so there is always an Uddeholm or ASSAB relpresentative close at hand

to give local advice and support. For us it is all a matter of trust

in long-term partnerships as well as in developing new products. Trust

is something you earn, every day.

For more information, please visit www.uddeholm.com, www.assab.com

or your local website.

pb uddeholm vidar superior english

Documents