four-post lift family - hunter l451t-ps, l454t-ps ... two stainless steel turnplates for...
TRANSCRIPT
AND VALIDATED
Four-Post Lift FamilyHigh-capacity open- and closed-front alignment lifts
WIDEST RUNWAYS!
Four-Post LiftsAvailable in long or short, open or closed configurations.
EXCLUSIVE
Two Swing Air Jacks
% Raise vehicles off runways
% 9,000-lb. capacity
EXCLUSIVE
Two Movable Work Steps
% 12 secure positions
% Lightweight design
EXCLUSIVE
Louvered Ramps
% Prevent wheel spin
% More effective than diamond tread or abrasive strips
NEW EXCLUSIVE
Extra-Wide Runways
% Accommodate vehicles up to 92" wide
26"
EXCLUSIVE
High-Capacity
% Lifts 18,000 lbs. (8164 kg)
% Best in class!
Other
Lift18,000 Pounds!
STANDARD
Flush Slipplates
% Wheelbases up to 158"
% Tethered pins secure plates on basic models
NEW OPTIONAL
Open-Front Workspace Available % Easy access to adjustment points and jacks
% Available on long- and standard-length runway racks
EXCLUSIVE
Louvered Locks
% 16 lock heights ensure runways are level
% Long-life galvanized cables
EXCLUSIVE
Umbilical Covering
% Strong and flexible
% Protects air and hydraulic lines from damage
EXCLUSIVE
Control Unit
% Easy-to-use console
% Powerful 3-hp motor
Model L451T-IS shown with optional AlignLights system
STANDARD
Pins and Pulleys
% Large-diameter iron pulleys with teflon bearings ensure long-life
% Chrome-plated pins
STANDARD
Integrated Air Line Kit
% Convenient power for air tools at front and rear
Models L451T-PS, L454T-PS
PowerSlide® ControlPush-button locks or unlocks the slipplates and turnplates.
PowerSlide® SlipplatesSecure slipplates with a single button. The technician no longer has to struggle to remove and replace slipplate pins for every alignment.
PowerSlide® edition saves time and hassle!
PATENTED
PowerSlide® Turnplates Save time by eliminating struggle with turnplate pins.
Only 3 Trips!
1 23
Yesterday's Technology
8 Trips
8 76 5
4 32 1
Minimize trips around the car1 Mount targets
2 Make adjustments
3 Remove targets
4 Jack vehicle and compensate sensors
5 Lower leveling legs (if equipped)
6 Remove slipplate and turnplate pins
7 Replace slipplate and turnplate pins
8 Raise leveling legs (if equipped)
EXCLUSIVE
PowerSlide® Locking System
Models L451T-IS, L454T-IS
FIA allows WinAlign® aligners to control lift features for ultimate productivity.*
* Alignment console sold separately.
FIA/Inflation Station edition maximizes productivity!
Integrated inflation reelsAutomatically fills or bleeds each tire.
Record tire pressurePrintouts record starting and final pressure.
FIA console Controls PowerSlide and Inflation Station features.
Model L451T-IS shown
Automatic lockingTurnplates and slipplates lock
and unlock at the right time. Locks automatically during lift descent.
PATENTED
Fully Integrated Alignment with Inflation Station and PowerSlide
STANDARD
Swing Air Jacks Hunter Swing Air Jacks add capabilities for lifting vehicles off the runways during alignment procedures and other multi-service operations.
% 9,000 lbs. (4,082 kg) capacity
% Combines low drive-on height with high lifting capacity needed to handle a wide range of vehicles
133-84-1 – 9,000-lb. Capacity Swing Air Jack
PATENTED
TurnplatesAll L451T and L454T models will ship with the most appropriate turnplates. When making a substitution, any of the following turnplates may be used.
20-2076-1 PowerSlide turnplates with automatic bridgesTwo stainless steel turnplates for camera-sensor systems.
20-2075-1 PowerSlide turnplates without automatic bridgesTwo stainless steel turnplates for conventional-sensor systems.
20-2532-1 Stainless steel turnplate kitTwo stainless steel Delrin-ball turnplates and bolt-on guide strips.
20-2533-1 Low-friction stainless steel turnplate kitTwo stainless steel Torlon ball turnplates and bolt-on guide strips.
20-2531-1 Powder-coated turnplate kitTwo powder-coated, Delrin-ball turnplates and bolt-on guide strips.
Integrated bridge lowers and raises as plates are locked, making rolling compensation a snap. Air-operated control system ties directly into PowerSlide® lifts (20-2076-1 shown).
EXCLUSIVE OPTIONAL
AlignLights systemHunter’s AlignLights lighting system provides an efficient light source underneath the vehicle.
% Powered by the main lift power source and requires no additional or exposed electrical cords.
% Automatically turns off when the lift is lowered to the floor and turns on when the lift is raised.
% AlignLights is an ALI listed accessory.
20-2993-1 – AlignLights system for four-post lifts
L451 and L454 elevation view
Because of continuing technological advances, specifications, models and options are subject to change without notice.
AND VALIDATED
The Hunter L451 and L454 Lifts have been certified under the program conducted by Automotive Lift Institute (ALI) to comply with Safety Standard ANSI/ALI ALCTV-2011 and Electrical Standard UL 201.
Standard-length lifts
JOINTFREEAREA
JOINTFREEAREA
31 in. x 31(787 mm x787 )
AREA FREEOF JOINTS INCONCRETE
(located underboth front post
baseplates)
in.
mm
20 1/2 in. x
(521 mmBY
)AREAFREE
OF JOINTSIN
CONCRETE(locatedunder
both rearpost
baseplates)
20 1/2 in.
521 mm
12 ft.- 3/8 in.(3667 mm)
15 ft.- 3 3/8 in. (4658 mm)RECOMMENDED BAY WIDTH
4 in.(102 mm)
OVERALLLENGTH:
21 ft.- 9 3/4 in.(6648 mm)
28 5/8 in.(727 mm)
18 ft.- 10 1/4 in.(5747 mm)
ROOM FOR ALIGNMENT CONSOLE
HAWKEYE AND PRONTO SYSTEMSHAVE SPACE REQUIREMENTS IN
FRONT OF THE LIFT THAT MUST BEMET, REFER TO APPROPRIATESENSOR SITE REQUIREMENTS.
31 1/2 in.(768 mm)
11 - 7 3/16(3535 mm)ft. in.
9 -10 11/16(3015 mm)
ft. in.
26(660 mm)
in.
40(1016 mm)
in.
28 in.(711 mm)
RUNWAYLENGTH:
ft. in.
(not shown)
18 - 3(5563 mm)
9 ft.- 9 3/8 in.(2981 mm)
For Lift with HE421Floor-Mounted
Sensors:FM, ML, LC or FM
Typ. 27 - 8 1/4 in.(8439 mm)
Specified Range28 - 4 1/2 in.
to 24 -11 1/4 in.(8649 mm
to 7601 mm)
(Refer to 6292-T,Floor-MountedSensor site.
For HE421CM:add 5 in. (127 mm)(
For HE421WM:Spec Rangeis expanded.
(
RECOMMENDEDBAY LENGTH
ft.
ft.ft.
)
Refer to 6291-T.)
Refer to 6290-T)
L451 plan view
Max. vehicle weight 18,000 lbs. (8164 kg)Max. wheelbase
General service 193 in. (4902 mm)Two-wheel alignment* 177 in. (4496 mm)Four-wheel alignment 158 in. (4013 mm)
Min. four-wheel alignment 88 in. (2235 mm)
Max. lifting height 75 in. (1905 mm)Alignment height Any of 16 lock positionsMinimum height 8.75 in. (222 mm)Overall height 98 in. (2489 mm)Tread width
Min. inside 40 in. (1016 mm)Max. outside 92 in. (2337 mm)
Motor3 hp, 208-230 VAC,
60 Hz, 1 phAir 90-150 psi (6.2-10.3 bar)** * Long wheelbase vehicles may require jacking compensation** 125 psi required for full jack capacity
L451T-IS L454T-IS L451T-PS L454T-PS L451JT L454JT
Open-front accessibility % % %
Fully Integrated Alignment % %
Inflation Station % %
PowerSlide® slipplates & turnplates % % % %
Stainless steel turnplates % %
Two 9,000-lb. Swing Air Jacks % % % % % %
Specifications
Standard equipment % Stainless steel turnplates (PowerSlide® turnplates on PS and IS models)
% Flush-mounted, full-floating slipplates (PowerSlide® slipplates on PS and IS models)
% Louvered ramps with built-in wheel stops
% Front wheel stops % Two wheel chocks
% Two movable work steps % Built-in, full-length jack rails % Built-in air line kit
Optional equipment % 20-3145-1 – 17.5" Ramp Extension Kit (for low-clearance vehicles)
% 20-3146-1 – 40" Ramp Extension Kit (for extremely low-clearance vehicles or high-floor-slopes)
16 in.(406 mm)
6 ft. 3 in.(1905 mm)MAXIMUMHEIGHT
MAXIMUM FLOOR ELEVATION CHANGE OF 3 in. (76 mm) BETWEEN POSTS (baseplate outer edges)
FOR SHORT RUNWAYS, 18 ft. 7 1/2 in. (5677 mm) FOR LONG RUNWAYS, 21 ft. 4 in. (6502 mm)
FOR ALL OPEN-FRONT LIFTS, ADD 2 3/4 in. (70 mm)(for larger front baseplates)
8 ft. 2 in.(2489 mm)
8 1/4 in.(210 mm) MINIMUMHEIGHT
13 ft.(3962 mm)MINIMUMCEILINGHEIGHT
Copyright © 2017, Hunter Engineering CompanyForm 6020-T, 03/17
Supersedes form 6020-T, 11/15
0317RH
Extended-length lifts
Standard and optional equipmentIdentical to L451 and L454 Lift Racks.
JOINTFREEAREA
JOINTFREEAREA
31 in. x 31(787 mm x787 )
AREA FREEOF JOINTS INCONCRETE
(located underboth front post
baseplates)
in.
mm
20 1/2 in. x
(521 mmBY
)AREAFREE
OF JOINTSIN
CONCRETE(locatedunder
both rearpost
baseplates)
20 1/2 in.
521 mm
12 ft.- 3/8 in.(3667 mm)
15 ft.- 3 3/8 in. (4658 mm)RECOMMENDED BAY WIDTH
4 in.(102 mm)
OVERALLLENGTH:
24 ft.- 6 1/4 in.(7474 mm)
28 5/8 in.(727 mm)
21 ft,- 6 3/4 in.(6572 mm)
ROOM FOR ALIGNMENT CONSOLE
HAWKEYE AND PRONTO SYSTEMSHAVE SPACE REQUIREMENTS IN
FRONT OF THE LIFT THAT MUST BEMET, REFER TO APPROPRIATESENSOR SITE REQUIREMENTS.
31 1/2 in.(768 mm)
11 - 7 3/16(3535 mm)ft. in.
9 -10 11/16(3015 mm)
ft. in.
26(660 mm)
in.
40(1016 mm)
in.
28 in.(711 mm)
RUNWAYLENGTH:
20 ft.-5 1/2 in.(6236 mm)
9 ft.- 9 3/8 in.(2981 mm)
For Lift with HE421Floor-Mounted
Sensors:FM, ML, LC or FM
Typ. 30 - 4 3/4 in.(9265 mm)
Specified Range31 - 3/4 in.
to 27 - 7 3/4 in.(9468 mm
to 8426 mm)
(Refer to 6292-T,Floor-MountedSensor site.
For HE421CM:add 5 in. (127 mm)(
For HE421WM:Spec Rangeis expanded.
(
RECOMMENDEDBAY LENGTH
ft.
ft.ft.
)
Refer to 6291-T.)
Refer to 6290-T)
L451L plan view***
*** See previous page for elevation view
Be sure to check out other Hunter literature for more quality products from Hunter Engineering.
Max. vehicle weight 18,000 lbs. (8164 kg)
Max. wheelbaseGeneral service 227 in. (5766 mm)
Two-wheel alignment* 211 in. (5360 mm)
Four-wheel alignment 158 in. (4013 mm)
Min. four-wheel alignment
88 in. (2235 mm)
Max. lifting height 75 in. (1905 mm)
Alignment height Any of 16 lock positions
Minimum height 8.75 in. (222 mm)
Overall height 98 in. (2489 mm)
Tread widthMin. inside 40 in. (1016 mm)
Max. outside 92 in. (2337 mm)
Motor3 hp, 208-230 VAC,
60 Hz, 1 ph
Air 90-150 psi (6.2-10.3 bar)** * Long wheelbase vehicles may require jacking compensation** 125 psi required for full jack capacity
Because of continuing technological advances, specifications, models and options are subject to change without notice.
PowerSlide and WinAlign are registered trademarks of Hunter Engineering Company. The PowerSlide logo is a trademark of Hunter Engineering Company.
The Hunter L451L and L454L Lifts have been certified under the program conducted by Automotive Lift Institute (ALI) to comply with Safety Standard ANSI/ALI ALCTV-2011 and Electrical Standard UL 201. AND VALIDATED
L451LT-IS L454LT-IS L451LT-PS L454LT-PS L451LJT L454LJT
Open-front accessibility % % %
Fully Integrated Alignment % %
Inflation Station % %
PowerSlide® slipplates & turnplates % % % %
Stainless steel turnplates % %
Two 9,000-lb. Swing Air Jacks % % % % % %
Specifications