lindab fasteners technical information components global/fasteners...lindab fasteners technical...

36
Lindab Coverline | Technical Information Fasteners Lindab Fasteners Technical Information Lindab Coverline TM

Upload: vuongdung

Post on 07-Mar-2018

245 views

Category:

Documents


1 download

TRANSCRIPT

Page 1: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

Lindab Coverl ine | Technical Information Fasteners

Lindab FastenersTechnical Information

Lindab Coverline TM

Page 2: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

Lindab Coverl ine | Fasteners

Dimensioning

Tolerances

Screw• Design of screw head, see relevant

product page• Length measurements are allowed

to vary by 5 %• Diameters are allowed to vary by

3 %

Nails• Design of nail head, see relevant

product page• Length measurements are allowed

to vary by ±4 %• Diameters are allowed to vary by

±4 %

Rivets• Design of rivet head, see relevant

product page• Length measurements (L) are al-

lowed to vary by ±0.5 mm• Main diameter (A) is allowed to vary

by ±0.3 mm• Rivet diameters (D) have tolerances

as specified below:

ScrewsStandardised failure forces for threaded screws in accordance with StBK-N5 - �3:51T = standardised tensile strength (kN/screw) characteristic value*.

Strength

Screw material*

Thread Diameter d mm

Aluminium SIS 43 38

Carbon steel case-hardened SIS 13 70

Stainless steel case-hardened SIS 23 02

Stainless steel

SIS 23 32, SIS 23 33 SIS 23 43

10 4.8 T4 T8 T8 T7

1� 5.5 T6 T11 T11 T10

14 6.3 T8 T15 T15 T13

16 8.0 T13 T�5 T�5 T��

Recommended operating loads in kN Concrete class

Concrete class K�5 K40

Tensile load 1.6 1.8

Transverse load �.0 �.0

Rivet Ø Tolerance

3.� -0.10 - +0.08

4.0 -0.15 - +0.08

4.8 -0.15 - +0.08

Type Diameter mm

Extraction forcekN

Shearing forcekN

AL/ST 3.� 1.5 1.�

AL/TEL 4.0 �.0 1.8

4.8 3.� �.7

ALT 3.� 1.5 1.1

4.0 �.1 1.8

4.8 3.6 �.6

TI 3.� 3.3 �.8

*Standardised shearing strength “S” is assumed to be 0.65 T (kN/cut, characteristic value).*Screw material of the alloys specified here or equivalent SS alloys.

Rivets(Actual values, not standardised)

Concrete anchor (K31 - K35)Minimum set depth: 30 mm minimum edge distance: 50 mm, in the event of trans-verse load 75 mmMinimum installation distance: 60 mm

Page 3: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

3

Lindab Coverl ine | Fasteners

Sealing washers

ScrewsConstruction screws with sealing wash-ers are supplied as standard in accor-dance with the table below.In accordance with the recommendation in the thin sheet standard, the rubber material is not electrically conductive.

X

Material, screw Screw diameter mm

Material washer Outer diameter washer, D mm

Carbon steel 4.8-5.5 Carbon steel 14

6.3-6.5 Carbon steel 16

Aluminium 5.6 Aluminium 14

Stainless steel 4.� Aluminium 1�

4.8 Aluminium 14

5.5 Stainless steel 14

6.3-6.5 Stainless steel 16

Panel screw Stainless steel 19

Type Ø nail

Dimen-sion

washer, mm

Colour washer

Tin nail �.5 6.5 × 3.0 × �.0

Grey

Clasp nail

3.5 9.0 × 3.5 × �.4

Grey or black

Dimensioning

Technical data:

Material: EPDMHardness, Shore A: 70 ± 5Tensile strength, MPa: 8.3Heat resistance:1�0°C continuous300°C max 30 min

Washer thicknesses, X :On overlap screws: 3.8 mmOther: �.8 mm

Standard washersScrews can also be supplied with other washer dimensions.

REMEMBER!Do not over-tighten construction screws with sealing washers; the material in our sealing washers is of a very high quality, but can be deformed when tightened too hard.

NailsNails are supplied with EPDM rubber sealing washers in accordance with the following table:

Page 4: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

4

Lindab Coverl ine | Fasteners

In order to ensure a suitable hole diam-eter, the procedure in accordance with StBK-N5 - 33:84�K should be applied.

Blind rivetsBlind rivets are installed in drilled or punched holes, hole diameter = rivet di-ameter + approx. 0.1 mm.

Concrete anchor (K31 - K35)Drill a hole Ø 6.5 mm, depth at least 40 mm + thickness of the component. Knock in the concrete anchor with a nor-mal hammer. When installing steel com-ponents, the hole in the component must be at least 8 mm, for thicker goods 8.5 mm.

Pipe flashers1. Before making a hole in the surface,

mark out the best position for the flasher.

�. Make an even hole with minimal tol-erance for the pipe.

3. The flasher should also provide a

Dimensioning

Installation instructions

Drilling screwUse power driver with depth stop that maintains a speed under load of 1500-�500 rpm when installing in material < � mm, and 1�00–1800 rpm when install-ing in thicker materials.

Self-tapping screw - without bitUse an infinitely variable or low speed power driver, suitable speed 300-600 rpm. Hole diameter in accordance with the table below, should be viewed as a guideline.

Ø Screw 4.8 4.8 4.8 6.5 6.3 6.3 6.3 6.3

Thickness surface

Wood 1.0-1.5 1.6-�.0 Wood 1.�5-1.5 �.0-3.0 4.0-6.0 7.0-�5.0

Thread type

A C C A C C B B

Ø drill hole

3.5 3.7 3.9 4.5 5.0 5.3 5.5 5.7

KL

watertight fit on the pipe. If the rub-ber needs to be cut to achieve the correct fit, use a sharp pair of scis-sors and avoid notches in the edge.

4. Apply silicone on the underside of the base, moisten the rubber with water and thread the tank opening over the pipe until it is in contact with the surface.

5. Press the base against the contours of the surface using your hands.

6. Secure the flasher at two points (1 and �, see fig.).

Continue to secure the flasher as il-lustrated to avoid gaps.

7. If there are sharp corners on the sur-face, use a blunt object to press the base into position.

8. Seal with additional silicone around the base.

Guideline drill diameters for self-tapping screws

ScrewsClamp lengthWood = Screw length -30 mmSteel = Fastened material + board etc. + surface

Page 5: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

5

Lindab Coverl ine | Fasteners

Basic conditions in accordance with the thin sheet standard: Fasteners must be of the same or higher grade than the basic mate-rial and adapted to the corrosion environment in question.Corrosivity classes in accordance with SS-EN ISO 1�944-� with regard to the corrosivity of the atmosphere as well as environ-mental examples.

Dimensioning

Corrosion protection/Corrosivity classes

We are continually adapting our production to the experiences that emerge in various independent investigations and tests. We also conduct field tests ourselves in order continually to follow up the quality of our products.Construction screws made of carbon steel for outdoor use in corrosivity class C� are electrogalvanised a minimum of �5µm, chrome-plated and painted with two-component polyurethane paint or polyester powder.

Corrosivity class

Environmental corrosivity

Outdoors Indoors

C1 Very low - Heated areas with dry air and insignificant pollutant volumes, e.g. offices, shops, schools, hotels.

C� Low Atmospheres with low pollutant volumes, e.g. rural areas.

Non-heated areas with varying temperatures and humidity levels. Low frequency of moisture condensation and low air pollutant content, e.g. sports halls, warehouses.

C3 Moderate Atmospheres with some salt or moderate air pollutant volumes. City areas and areas of light industry. Areas influenced to some extent by the coast.

Areas with moderate humidity and large air pollutant volumes from production processes, e.g. breweries, dairies, laundrettes.

C4 High Atmospheres with moderate amounts of salt or tangible air pollutant volumes. Industrial and coastal areas.

Areas with a high humidity and large air pollutant volumes from production processes, e.g. chemical industrials, swimming baths, shipyards.

C5-I Very high (Industrial) Industrial areas with high air humidity and an aggressive atmosphere.

Areas with almost permanent moisture condensation and large air pollutant volumes.

C5-M Very high (Marine) Coastal and offshore areas with large amounts of salt.

Areas with almost permanent moisture condensation and large air pollutant volumes.

Examples of typical environments in the temperate climate zone (informative)

Material qualityScrewsCarbon steel SAE1018 (SS1370)

Aluminium �0�4 (SS4338)

Drilling stainless steel Marutex®

Marutex® is a stainless steel drilling screw that is made of a special stainless steel. After heat treatment, the steel achieves a hardness fully comparable with hardened carbon steel. The Marutex® screw’s unique drilling properties, in combination with very high corrosion resistance, puts this screw in a class of its own. Marutex® has obtained a technical approval within the EU for use up to and including corrosivity class C4. Marutex® has been estimated having a service life of 50 years.

Self-tappingstainless steel -SAE304 (SS�33�)

NailsCarbon steel AISI 101�

Stainless steel AISI 304 (SS�333)

Copper SS5010

Rivets Material Material rivets splints

AL/ST Al/3.5 % Mg Steel

TI-A2 Stainless Stainless steel, steel,

AISI 305 AISI 304

Sealing washers - screwMetal

Steel, aluminium and stainless steel

RubberThe rubber, which has been vulcanised to the metal, is a high-grade EPDM rubber. It is characterised by extraordinary proper-ties as regards ozone and weather resist-ance, and also demonstrates very good

wear resistance.

Sealing washers, nails and pipe flashersRubber

High-grade EPDM rubber

Page 6: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

6

Lindab Coverl ine | Fasteners

U-nite Fasteners Technology AB now has more than �0 years’ experience of paint-ing construction and industrial screws. During this time we have continually devel-oped our technology, painting both with wet paint and powder.

Wet paintOur wet painting facility has the capacity to paint �00,000 screws per shift. After pre-treatment, the screw is painted with two-component polyurethane paint.

Polyurethane paint is generally char-acterised by very good outdoor resis-tance and high resistance to mechanical influences. The paint also offers good colour resistance, without chalking or fading, which makes it particularly suit-able for acidic environments. The paint we use has also been further adapted to cope with the very tough treatment to which it will be subjected. The colour system is evaluated regularly and has proven to satisfy extremely stringent re-quirements.

Powder paintWe have used powder paint, primarily on construction screws, since 1991. In close collaboration with our powder sup-plier, who is a leader in the field in Eu-

rope, we have developed a polyester powder that gives a very hard-wearing and even surface layer. Powder paint is free of solvents, which we consider to be a major advantage, benefiting both the

working and the external environment. Our powder facility has the capacity to paint 300,000 fasteners per shift.

ColoursConstruction and industrial screws can, in most cases, be supplied in any colour in accordance with NCS, RAL or ac-cording to colour tests. Construction metal screws are stocked in around 15 standard colours. We also stock paint in

all the Scandinavian sheet profilers’ co-lours, which can be delivered at short notice thanks to a very flexible manufac-turing process.Clasp and tin nails are stocked in some ten colours.Blind rivets, some dimensions are stocked in five colours.

Verification/testingIn order to ensure high, even quality in our paint systems, we take regular samples from our production process. Samples are taken from each con-signment to check the resistance of the paint to external influences/me-chanical wear and for colour check-ing. Different types of corrosion test are performed regularly to check col-our systems and surface treatment. Accelerated corrosion tests, salt spray, humidity cabinet and SCAB tests are conducted in co-operation with our paint suppliers, as well as by inde-pendent testing institutes. We also conduct field tests ourselves. Along-side our paint suppliers, we are con-tinually developing our paint systems, although no changes are implement-ed without extremely comprehensive testing.

Dimensioning

Paint systems

Surface treatmentScrewsCarbon steelBright zinc-plating 1�µm + chrome-platingFe/Zn 1�c1 or Spex® =>C1

Bright zinc-plating �5µm + chrome-plating Fe/Zn �5c1 + painting =>C�

Aluminium White pickling =>C4

Stainless steel Marutex®

Wax treatment =>C4

Stainless steel-A2Wax treatment =>C4

NailsTin nails:Carbon steel Bright zinc-plating 30µm + chrome-plating + painting =>C1(C�)

Copper >C4

Stainless steel-A2Bright =>C4

Clasp nails:Carbon steel Hot-dip galvanising 50µm =>C4

Stainless steel-A2Bright =>C4

Sealing washersSteelHot-dip galvanising min. �5µm(+ painting) =>C�

Aluminium White pickling =>C4

Stainless steelBright =>C4

Verification/testingSurface treatments are checked regularly, the zinc layer is checked on every batch using our own measuring equipment. In addition, accelerated corrosion tests such as salt spray and Kesternich tests are car-ried out by independent testing institutes in order to maintain a high, even level of qual-ity. We conduct field tests ourselves.

Page 7: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

7

Lindab Coverl ine | Fasteners

Dimensioning

Dimensioning valuesConditionsAll data are calculated in accordance with

• Boverket’s (National Swedish Board of Building, Planning and Housing) design regulations BKR 99

• Thin sheet standard StBK-N5

The fastener must never be the weakest link in a joint when subjected to shearing loads.

For safety reasons, power-absorbing joints must always have at least � fas-teners.

The dimensioning values are specified in kN/fastener and apply to safety class 1.

For safety classes � and 3, all the specified values are divided by 1.1 and 1.� respectively.

Edge and centre distances in the event of shearing force

a min. b min.

Screws 3d 1.5dRivets 3d 1.5dNails for firing tools 4.5d 4.5d

where d is the diameter of the fastener.

The length of the joint is restricted to a maximum of 15 d between the outer-most fasteners in the direction of the force, see StBK-N5 33:133.

Force analysis

In principle, a joint can be loaded with both extraction and shearing forces, see figure.

t is the thickness of the sheet nearest the head of the fastener.t1 is the thickness of the lower sheet.

If the joint is reversed, i.e. the fastener’s head comes up against the thickest sheet t1, adjust in all tables t = t1. The fol-lowing load cases can occur:

Fu

• Extraction from surface• Pulling through, punching through• Tensile failure in fastener

Fs

• Failure of edge of hole• Shearing failure in fastener• Tilt (only applies to wood)

Tensile force Fu and shearing force Fs can both affect the fastener at the same time. In this case check

+ ≤ 1Fu

Fud

Fs

Fsd

b

b

a

aaa

t1

t

Fs

Fu

Shearing force, construction screwsDimensioning value Fsd kN/screw. Attention is paid both to failure of the edge of the hole and shearing failure in the screw. Safety class 1.

t1

t

Fsd

In the area of number pairs in the table and marked *, shearing failure in the screw is decisive.The value to the left in each number pair relates to carbon steel screws, while the number to the right relates to stainless steel screws.

Nom t mm When

calculating t mm

Tensile yield limit

N/mm2

Screw diameter 4.2 mm

Screw diameter 4.8 mm

Screw diameter 5.5 mm

Screw diameter 6.3 mm

t1 =t t1 = 2.5 t t1 =t t1 = 2.5 t t1 =t t1 = 2.5 t t1 =t t1 = 2.5 t

0.4 0.3� �50 0.�6 0.54 0.�8 0.61 0.30 0.70 0.3� 0.81

0.5 0.41 �50 0.38 0.69 0.40 0.79 0.43 0.90 0.46 1.03

0.6 0.5� �50 0.5� 0.86 0.56 0.98 0.60 1.1� 0.64 1.�9

0.7 0.60 350 0.93 1.41 1.00 1.61 1.07 1.85 1.14 �.1�

0.8 0.73 350 1.�5 1.7� 1.34 1.96 1.43 �.�5 1.53 �.58

1.0 0.93 �50 1.�9 1.56 1.38 1.79 1.47 �.05 1.58 �.34

1.0 0.93 350 1.80 �.19 1.93 �.50 �.06 �.86 �.�1 3.�8

1.� 1.13 350 �.41 �.66 �.58 3.04 �.76 3.48 �.95 3.99 1.5 1.4� �50 �.39 �.39 �.60 �.73 �.78 3.1� �.97 3.58

1.5 1.4� 350 3.03* 3.03* 3.63 3.8� 3.64 3.89 4.37 4.16 5.01

�.0 1.91 350 3.03* 3.03* 4.16 3.64 4.16 3.64 5.7� 5.�0 5.7� 5.�0 6.49 6.74 �.5 �.40 350 3.03* 3.03* 4.16 3.64 4.16 3.64 5.7� 5.�0 5.7� 5.�0 7.80 6.76 7.80 6.76

Page 8: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

8

Lindab Coverl ine | Fasteners

Dimensioning

Tensile force, construction screwsThe dimensioning value Fud is deter-mined as the smallest value of Fud1 and Fud� in accordance with the tables be-low.

Extraction from steel surfaceDimensioning value Fud1 kN/screw. Screw diameter 5.5 mm.Safety class 1.

t1

t

Fud

Nominal t1 mm

When calculating t1 mm

Self-tapping screws Drilling screws

Tensile yield limit N/mm�, for the lower sheet t1

250 350 250 350

0.6 0.5� - - 0.3� 0.45 0.7 0.60 - - 0.41 0.57 0.8 0.73 - - 0.55 0.77 1.0 0.93 0.83 1.16 0.79 1.10 1.� 1.13 1.01 1.41 1.06 1.48 1.5 1.4� 1.�7 1.78 1.49 �.08 �.0 1.91 1.71 �.39 �.3� 3.�5 �.5 �.40 �.15 3.00 3.�7 4.58 3.0 3.00 �.68 3.75 4.57 6.40 3.5 3.50 3.13 4.38 5.76 8.06 4.0 4.00 3.58 5.00 7.04 9.85 5.0 5.00 4.47 6.�6 9.83 13.77 6.0 6.00 5.36 7.50 1�.93 18.10

Conversion factors 4.� mmfor other screw diameter 4.8 mm 6.3 mm

- - 0.87 0.87 0.87 0.87 0.93 0.93 1.15 1.15 1.07 1.07

In the event of a washer with a different diameter, multiply the table values by

9.5 mm 1� mm 14 mm 19 mm

0.4 0.7 1.0 1.�

Sheet nearest screw head

Nominal t mm

Tensile yield limit

N/mm2

0.4 �50 1.�0 1.08 0.84

0.5 �50 1.54 1.38 1.08

0.6 �50 1.91 1.7� 1.34

0.7 350 3.15 �.84 �.�1

0.8 350 3.83 3.45 �.68

1.0 350 4.88 4.39 3.4�

1.� 350 5.93 5.34 4.15

Pull-through failure, punching throughDimensioning value Fud� kN/screw. Washer with diameter 14 mm. The distance from screw to free sheet end must be greater than the width of the profile base, although at least �5 mm. Safety class 1.

Within the area check that tensile failure does not take place in the screw according to:

Diameter mm 4.� 4.8 5.5 6.3 Carbon steel kN/screw

4.6 6.4 8.8 1�.0

Stainless steel kN/screw

- 5.6 8.0 10.4

Page 9: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

9

Lindab Coverl ine | Fasteners

Dimensioning

Shearing force, blind rivetExtraction from steel surfaceDimensioning value Fsd kN/rivet.In the tables, attention has been paid to extraction, pull-through failure and tensile failure in the rivet. The values apply to both aluminium and Monel rivets. Safety class 1.

Tensile force, blind rivetExtraction from steel surfaceDimensioning value Fud kN/rivet.Attention has been paid both to hole edge failures and shearing failures in the rivet.Safety class 1.

t1

t

Fud

In the area of the table containing number pairs, shearing failure in the rivet is decisive.The value to the left relates to aluminium and the value to the right relates to Monel rivets.

Nominalt mm

When calcu latingt mm

Tensile yield limit

N/mm2

Rivet diameter 4.0 mm

Rivet diameter 4.8 mm

Rivet diameter 6.4 mm

t1 =t t1 = 2.5t t1 =t t1 = 2.5t t1 =t t1 = 2.5t

0.4 0.3� �50 0.�5 0.51 0.�8 0.61 0.3� 0.8�

0.5 0.41 �50 0.37 0.66 0.40 0.79 0.46 1.05

0.6 0.5� �50 0.51 0.8� 0.56 0.98 0.64 1.31

0.7 0.60 350 0.88 0.91 0.88 1.34 1.00 1.�8 1.61 1.15 �.15

0.8 0.73 350 0.88 1.�� 0.88 1.64 1.�8 1.34 1.�8 1.96 1.55 �.48 �.6�

1.0 0.93 �50 0.88 1.�6 0.88 1.49 1.�8 1.38 1.�8 1.79 1.59 �.48 �.38

1.0 0.93 350 0.88 1.76 0.88 1.9� 1.�8 1.93 1.�8 �.50 �.�� �.48 3.33

1.� 1.13 350 0.88 1.9� 0.88 1.9� 1.�8 �.58 1.�8 �.80 �.48 �.98 �.48 4.05

1.5 1.4� �50 0.88 1.9� 0.88 1.9� 1.�8 �.60 1.�8 �.73 �.48 3.00 �.48 3.64

1.5 1.4� 350 0.88 1.9� 0.88 1.9� 1.�8 �.80 1.�8 �.80 �.48 4.�0 �.48 4.96

�.0 1.91 350 0.88 1.9� 0.88 1.9� 1.�8 �.80 1.�8 �.80 �.48 4.96 �.48 4.96

�.5 �.40 350 0.88 1.9� 0.88 1.9� 1.�8 �.80 1.�8 �.80 �.48 4.96 �.48 4.96

t1

t

Fsd

The blind rivets are made of alumini-um AA 5056 or Monel.

Nominal t1 mm

When calculating

t1 mm

Tensile yieldlimit

N/mm2

Rivetdiameter 4.8 mm

Rivetdiameter 6.4 mm

0.4 0.3� �50 0.19 0.�6

0.5 0.41 �50 0.�5 0.33

0.6 0.5� �50 0.31 0.41

0.7 0.60 350 0.50 0.67

0.8 0.73 350 0.61 0.8�

1.0 0.93 �50 0.56 0.74

1.0 0.93 350 0.78 1.04

1.� 1.13 350 0.95 1.�7

1.5 1.4� �50 0.85 1.14

1.5 1.4� 350 1.19 1.59

�.0 1.91 350 1.60 �.14

�.5 �.40 350 1.60* �.69

* If Monel rivets are used, the value increases to �.0�.

Page 10: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

10

Lindab Coverl ine | Fasteners

Dimensioning

Fasteners, woodConditionsClimate class 1 and � in accordance with Design regulations BKR 99. In cli-mate class 3, the values depending on wood are reduced by �5%. Screws and nails must be fastened at right angles to the direction of the fibre.

Minimum edge and centre distance

Con-struction screws

Nails

Along the fibre direction

7d 10d

Across the fibre direction

4d 5d

Tensile force, construction screwsExtraction from wood surface

Dimensioning value Fud1 kN/screw.Screw diameter 4.8 mm.

Thread length Igf mm in wood

Fud1

�0 0.53

30 1.�1

40 1.88

50 �.44

If the screw diameter is mm

multiply the values by

5.5 1.10

6.5 1.�3

Also check the sheet for pull-through failure, punching Fud� in accordance with page 00.The minimum value of Fud1 and Fud� is di-mensioning.

Shearing force, construction screwsShearing force in wood (tilt)

Dimensioning value Fsd1 kN/screw.

Diameter d mm

Screw length mm

Fsd1

4.8 = 38 0.65

6.5 = 50 1.13

Also check the case Fsd in accordance with page 7 with t1 = t.The minimum value of Fsd1 and Fsd is di-mensioning.

Tensile force and shearing forces, nailsDimensioning values for extraction Fud and for tilt Fsd kN/nail.

Nail designa-tion

Diameter mm

Lengthmm

Fud Fsd

Façade nails 3.5 30 0.�6 1.14

Façade nails 3.5 40 0.34 1.14

Tin nails �.5 30 0.18 0.57

Mounting Shaft

diameter mm Fsd

Steel profile thickness

bmin*mm

Nails for firing tools in concrete

3.7 1.1 For all t 70

4.5 �.5 3.8 4.0

t = 0.7 mm t = 1.0 mm t > 1.0 mm

80

Nails for firing tools in steel

3.7 1.5 For all t �0

4.5 �.5 3.8 4.0

t = 0.7 mm t = 1.0 mm t > 1.0 mm

�0

Expanders in concrete

M6 �.5 3.0 t = 0.7 mm t > 0.7 mm

60

M6 1.5 For all t 40

* Minimum distance to concrete and steel edge.

Also check the case Fsd in accordance with page 7 with t1 = t.The values are reduced in relation to the diameter, for example 3.5/4.8 · the value in the table.

Fasteners, concrete and steelShearing force - nails for firing tools and expandersThe dimensioning value Fsd kN/nail.Attention is paid both to failure of the edge of the hole and shearing failure in the nail.Safety class 1.

Page 11: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

11

Lindab Coverl ine | Fasteners

DesignationDimen-

sionDrilling

capacityCorrosivity

classStainless

steelQuantity/

packArea of application

A10 4.8 x �8 4 x 0.5 C1-C� �50All-round screw for securing metal-plate to timber. (Drill bit)

A11 4,8 x �5 3 x 0,5 C�-C3 �50For mounting indoor and outdoor facades.

A12 4.8 x 35 3 x 0.5 C1-C� �50All-round screw for securing metal-plate to timber. (Sharp tip)

A134.8 x 35 4 x 0.5 C1-C� �50

All-round screw for securing metal-plate to timber. (Drill bit)

A13K

A14 4.8 x 51 4 x 0.5 C1-C� �50Mounting in timber where higher extraction value is required.

A15 4.8 x 64 4 x 0.5 C1-C� �00Mounting in timber where higher extraction value is required.

A216.5 x 51 � x 1.5 C1-C� �00

Mounting of metal-plate in laminated timber where extreme extraction values are required.A21F

A30K 4.� x �5 � x 0.9 C4 • �50 External flashing fastening.

A314.8 x 35 4 x 0.5 C4 • �50

Outdoor all-round screw for securing metal-plate to timber. (Drill bit)

A31K

A515.5 x 40 4 x 0.5 C4 • �50

Outdoor screw for mounting in wood where higher extraction value is required.A51K

A41 5.6 x 35 4 x 0.5 C4 alu �50Aluminium screw solely for mounting aluminium sheet in wood. (Drill bit)

A61 6.5 x 50 � x 1.0 C4 • �00Mounting of metal-plate in glulam where extreme extraction values are required.

Roofing and cladding to timber.

Technical data

Screws for construction

Unifast

Roofing and cladding to timber continues on page 12

Page 12: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

1�

Lindab Coverl ine | Fasteners

DesignationDimen-

sionDrilling

capacityCorrosivity

classStainless

steelQuantity/

packArea of application

A19 4.8 x 35 4 x 0.5 C1-C� �50Screw with wings for mounting corrugated plastic roof sheets to timber.

A72 4.8 x 35 - C1-C� �50Pipe clip screw with fibre cut tip for lower tightening torques and minimised risk of crack formation. Torx drive T�0.

A75 4.8 x 35 - C4 • �50

Stainless steel pipe clip screw for mounting in roof panel. Fibre cut tip for lower tightening torques and reduced risk of crack formation. Torx drive T�0.

A76 4.8 x 75 - C4 • 100

Stainless steel pipe clip screw for mounting in roof panel. Fibre cut tip for lower tightening torques and reduced risk of crack formation. Torx drive T�0.

A77 5.0 x 35 - C4 • 500 Stainless steel pipe clip screw for foot pipe clip. Pozi drive no. �.

A81 3.9 x �0 - C4 • 500 Stainless steel tin screw with fibre cut tip for lower tightening torques and reduced risk of crack formation. Torx drive T15.A82 3.9 x �5 - C4 • 500

A85 4.3 x �5 - C4 • 500Stainless steel screw for sliding clasps. Torx drive T�0.

A87 4.5 x �5 - C4 • 500Stainless steel screw for sliding clasps. Phillips drive no. �.

Other applications to timber.

Technical data

Screws for construction

Unifast

continued from page 11

Page 13: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

13

Lindab Coverl ine | Fasteners

DesignationDimen-

sionDrilling

capacityCorrosivity

classStainless

steelQuantity/

packArea of application

Light steel framing screw

B08

4.8 x 16 � x 0.56 - � x 1.5

C1

500, 1000

Selfdrilling screw for joining steel joists and profiles. The low head prevents damage to e.g. plasterboard. Phillips drive no. �.

B08BAND 1000Collated version for more rapid installation with automatic screwgun. 50pcs/strip.

Roofing and cladding to light section steel

B11 4.� x 13 1.0 - � x 1.5 C1-C� 500 Indoor, flashings in thin profiles.

B214.8 x �0 1.� - � x �.0 C1-C� �50

All-round screw, roofing and cladding to light section steel.

B21K

B23 4.8 x 3� 1.� - � x �.0 C1-C� �50All-round screw, roofing and cladding to light section steel.

B31 5.5 x �0 1.5 - � x �.5 C1-C� �50All-round screw, roofing and cladding to light section steel.

B32

5.5 x �5 1.5 - � x �.5 C1-C� �50All-round screw, roofing and cladding to light section steel, pipe clip screw, etc. B32F

B33

5.5 x 3� 1.5 - � x �.5 C1-C� �50All-round screw, roofing and cladding to light section steel, longer clamp length. B33K

B42

6.3 x �5 1.5 - � x 3.0 C1-C� �50Intended for joining lightweight steel constructions when high extraction values are required.B42F

KL: �0 mm

KL: 8 mm

Technical data

Screws for construction

KL = Clamp lengthRoofing and cladding to light section steel continues on page 14

KL: 6 mm

KL: 8 mm

KL: 13 mm

KL: 17 mm

KL: 11 mm

KL: 8 mm

Unifast

KL: 16 mm

KL: 17 mm

KL: 13 mm

KL: 14 mm

Page 14: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

14

Lindab Coverl ine | Fasteners

continued from page 13

DesignationDimen-

sionDrilling

capacityCorrosivity

classStainless

steelQuantity/

packArea of application

B51 4.� x 13 1.0 - � x 1.5 C4 • 500 Outdoor flashings in thin profiles.

B52 4.� x 16 1.0 - � x 1.5 C4 • 500 Outdoor flashings in thin profiles.

B61 4.8 x 16 1.� - � x �.0 C4 • �50Outdoor, roofing and cladding to light section steel, short clamp length..

B624.8 x �0 1.� - � x �.0 C4 • �50

Outdoor, roofing and cladding to light section steel.

B62K

B63 4.8 x �5 1.� - � x �.0 C4 • �50Outdoor, roofing and cladding to light section steel.

B64 4.8 x 40 1.� - � x �.0 C4 • �50Outdoor, roofing and cladding to light section steel, longer clamp length.

B71

5.5 x �0 1.5 - � x �.0 C4 • �50Outdoor, roofing and cladding to light section steel.

B71K

B72

5.5 x �� 1.5 - � x 3.0 C4 • �50Outdoor, roofing and cladding to light section steel, higher drilling capacity.

B72K

B73 5.5 x �5 1.5 - � x �.0 C4 • �50Outdoor, roofing and cladding to light section steel.

B75 5.5 x 35 1.5 - � x �.0 C4 • �50Outdoor, roofing and cladding to light section steel where long clamp length

B74

5.5 x 40 1.5 - � x �.0 C4 • �50Outdoor, roofing and cladding to light section steel where long clamp length is required.B74K

B82 6.3 x �5 1.5 - � x 3.0 C4 • �50Outdoor, roofing and cladding to light section steel where higher strength is required.

KL: 6 mm

KL: 1� mm

KL: 11 mm

KL: 11 mm

KL: �6 mm

KL: 6 mm

KL: 1� mm

KL: �6 mm

Technical data

Screws for constructionRoofing and cladding to light section steel.

Unifast

KL: 8 mm

KL: �6 mm

KL: 11 mm

KL: 8 mm

KL: 4 mm

KL: 7 mm

KL: 7 mm

KL: 14 mm

KL = Clamp length

Page 15: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

15

Lindab Coverl ine | Fasteners

DesignationDimen-

sionDrilling

capacityCorrosivity

classStainless

steelQuantity/

packArea of application

C11 5.5 x �3 4.0 - 8.0 C1-C� �50Screw for lightweight steel construction to lightweight steel construction or light-weight steel construction to ridge plate.

C21

5.5 x 3� 4.0 - 1�.0 C1-C� �50All-round screw for roofing and cladding to heavy section steel. With sealing washer or large flange.C21F

C22 5.5 x 51 4.0 - 1�.0 C1-C� �00All-round screw for mounting in heavy section steel, long clamp length.

C31 5.5 x �6 4.0 - 9.0 C4 • �50Outdoor screw for roofing and cladding to heavy section steel. Flashings in doorways.

C41

5.5 x 3� 4.0 - 1�.0 C4 • �50Outdoor screw for roofing and cladding to heavy section steel.

C41K

C42 5.5 x 45 4.0 - 1�.0 C4 • �50Outdoor screw for roofing and cladding to heavy section steel, long clamp length.

KL: �� mm

Roofing and cladding to heavy section steel.

KL: 10 mm

KL: 10 mm

KL: 30 mm

KL: 1� mm

KL: 10 mm

Screws for construction

KL: 10 mm

Unifast

KL: 10 mm

Technical data

KL = Clamp length

Page 16: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

16

Lindab Coverl ine | Fasteners

Stiching screws for roofing and cladding.

Technical data

Screws for construction

DesignationDimen-

sionDrilling

capacityCorrosivity

classStainless

steelQuantity/

packArea of application

D14

4.8 x 19 4 x 0.5 C1-C� �50All-round screw for stiching of thin metal-plates.

D14K

D21 5.5 x �0 4 x 0.5 C1-C� �50All-round screw for stiching of thin metal-plates, in event of sheet action.

D21F 5.5 x �0 3 x 0.9 C1 �50 Stiching of high profiles

D32F 6.3 x �� 3 x 0.9 C1 �50Stiching of high profiles suitable for sheet action calculation.

D33F 6.3 x 3� 3 x 0.9 C1 �50Stiching of high profiles suitable for sheet action calculation.

D41 4.� x 13 4 x 0.5 C4 • 500 Outdoor flashing fastening.

D42 4.� x 16 4 x 0.5 C4 • �50 Outdoor flashing fastening.

D51

4.8 x 19 3 x 0.7 C4 • �50Oudoor stiching of thin metal-plates.

D51K

D61 5.5 x 19 3 x 0.7 C4 • �50Oudoor stiching of thin metal-plates in event of sheet action.

D71K 6.3 x �� 3 x 0.7 C4 • �50Oudoor stiching of thin metal-plates in event of sheet action.

Unifast

Page 17: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

17

Lindab Coverl ine | Fasteners

Roofing and cladding + board to light section steel.

Technical data

Screws for construction

DesignationDimen-

sionDrilling

capacityCorrosivity

classStainless

steelQuantity/

packArea of application

E11 5.5 x 36 1.� - � x �.0 C1-C� �50Suitable for thin board, such as plasterboard.

E12 5.5 x 51 1.� - � x �.0 C1-C� �50All-round screw for all kinds of board thicknesses on walls.

E13 5.5 x 47 1.5 - � x �.5 C1-C� �50Board screw for thicker boards. Larger thread under the head for good tightness against the metal-plate.

E14 5.5 x 76 1.5 - � x �.5 C1-C� 150Board screw for thicker boards. Larger thread under the head for good tightness against the metal-plate.

E23 5.5 x 43 1.5 - � x �.0 C4 • �50Outdoor board screw for board up to 15 mm.

E24 5.5 x 34 1.5 - � x �.0 C4 • �50Outdoor board screw for thicker boards. Larger thread under the head for good tightness against the metal-plate.

E25 5.5 x 50 1.5 - � x �.0 C4 • �50Outdoor board screw for thicker boards. Larger thread under the head for good tightness against the metal-plate.

KL: 14 mm

KL: �� mm

KL: ��-34 mm

KL: 4�-6� mm

KL: 16-�1 mm

KL: �6-38 mm

Unifast

DesignationDimen-

sionDrilling

capacityClamp

length mmCorrosivity

classStainless

steelQuantity/

packArea of application

Sandwich panels to light section steel

E33 5.5 x 98 1.5 - � x �.5 55-83 C1 100

Screw for indoormounting of sandwich panels to lightweight steel constructions

E34 5.5 x 1�0 1.5 - � x �.5 65-105 C1 100

E35 5.5 x 130 1.5 - � x �.5 75-115 C1 100

E36 5.5 x 150 1.5 - � x �.5 75-135 C1 100

E37 5.5 x 180 1.5 - � x �.5 105-165 C1 100

E38 5.5 x �00 1.5 - � x �.5 1�5-185 C1 100

E39 5.5 x �30 1.5 - � x �.5 155-�15 C1 100

E41 5.5 x 80 1.5 - � x 3.0 43-63 C4 • 100Stainless steel screw for outdoor mounting of sandwich panels in lightweight steel constructions/beams.

E42 5.5 x 100 1.5 - � x 3.0 53-8� C4 • 100

E43 5.5 x 1�5 1.5 - � x 3.0 66-107 C4 • 100

E44 5.5 x 150 1.5 - � x 3.0 91-131 C4 • 100

E45 5.5 x 174 1.5 - � x 3.0 110-156 C4 • 100

Sandwich panels to light section steel

Screws for construction

Unifast

Sandwich panels screws continues on page 18

KL: 18 mm

Page 18: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

18

Lindab Coverl ine | Fasteners

DesignationDimen-

sionDrilling

capacity

Clamp length

mm

Corrosivity class

Stain-less steel

Quantity/pack

Area of application

Sandwich panels to heavy section steel

E50 5.5 x 75 4.0 - 1�.5 3�-40 C1 100

Screw for indoor mounting of sandwich panels in steel beams

E51 5.5 x 85 4.0 - 1�.5 45-51 C1 100

E52 5.5 x 105 4.0 - 1�.5 45-69 C1 100

E53 5.5 x 130 4.0 - 1�.5 68-95 C1 100

E54 5.5 x 150 4.0 - 1�.5 68-115 C1 100

E55 5.5 x 175 4.0 - 1�.5 93-140 C1 100

E56 5.5 x 190 4.0 - 1�.5 108-155 C1 100

E57 5.5 x �10 4.0 - 1�.5 1�8-175 C1 100

E58 5.5 x �40 4.0 - 1�.5 160-�05 C1 100

E59 5.5 x �85 4.0 - 1�.5 �08-�50 C1 100

E61 5.5 x 85 4.0 - 1�.0 48-61 C4 • 100

Stainless steel screw for outdoor mounting of sandwich panels in steel beams.

E62 5.5 x 100 4.0 - 1�.0 56-76 C4 • 100

E63 5.5 x 1�0 4.0 - 1�.0 66-96 C4 • 100

E64 5.5 x 150 4.0 - 1�.0 81-1�6 C4 • 100

E65 5.5 x 185 4.0 - 1�.0 1�0-16� C4 • 100

Sandwich panels to timber

E70 6.5 x 80 � x 0.9 <30 C4 • 100

Stainless steel screw for outdoor mounting of sandwich panels in steel beams.

E71 6.5 x 100 � x 0.9 <50 C4 • 100

E72 6.5 x 1�0 � x 0.9 <70 C4 • 100

E73 6.5 x 140 � x 0.9 <90 C4 • 100

E74 6.5 x 160 � x 0.9 <110 C4 • 100

E75 6.5 x 180 � x 0.9 <130 C4 • 100

E76 6.5 x �00 � x 0.9 <150 C4 • 100

E77 6.5 x ��0 � x 0.9 <170 C4 • 100

Sandwich panel washer

NG4 39 x �9 – – C4 100 Sandwich Panels model G4

Sandwich panels to heavy section steel/timber.

Technical data

Screws for construction

Unifast

continued from page 17

Page 19: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

19

Lindab Coverl ine | Fasteners

Self-tapping, Type A

Technical data

Screws for construction

Designation DimensionCorrosivity

classStainless

steelQuantity/

packArea of application

FA13 6.5 x 38 C1-C� �50

Self-tapping screw for pre-drilled holes, intended for mounting in wood. At least 30 mm of the screw should be secured in the surface. Dimensioning of extraction values is necessary in certain cases. Long dimensions are suitable for mounting sandwich panels in ti.

FA14 6.5 x 51 C1-C� �00

FA15 6.5 x 64 C1-C� 150

FA16 6.5 x 75 C1-C� 150

FA20 6.5 x 100 C1-C� 100

FA24 6.5 x 150 C1-C� 100

FA25 6.5 x 175 C1-C� 100

FA26 6.5 x �00 C1-C� 100

FA52 4.8 x �5 C4 • �50

FA53 4.8 x 38 C4 • �50

Stainless steel self-tapping screw for pre-drilled holes, intended for mounting in wood. At least 30 mm of the screw should be secured in the surface. Dimensioning of extraction values is necessary in certain cases. Long dimensions are suitable for external mounting of sandwich panels in timber.

FA54 4.8 x 51 C4 • �50

FA63 6.5 x 38 C4 • �50

FA64 6.5 x 51 C4 • �00

FA65 6.5 x 64 C4 • 150

FA66 6.5 x 75 C4 • 150

FA70 6.5 x 100 C4 • 100

FA73 6.5 x 130 C4 • 100

FA74 6.5 x 150 C4 • 100

FA75 6.5 x 175 C4 • 100

FA76 6.5 x �00 C4 • 100

FA77 6.5 x ��0 C4 • 100

FA79 6.5 x �60 C4 • 100

Unitap

Page 20: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

�0

Lindab Coverl ine | Fasteners

Self-tapping, Type B

Technical data

Screws for construction

Designation DimensionCorrosivity

classStainless

steelQuantity/

packArea of application

FB11 6.3 x 19 C1-C� �50Self-tapping screw for pre-drilled holes, intended for mounting in thick steel/beams with material thickness 3-�5 mm. See installation instructions for choice of drill diameter. Long dimensions are suitable for mounting sandwich panels in steel beams.

FB12 6.3 x �5 C1-C� �50

FB16 6.3 x 75 C1-C� 150

FB20 6.3 x 100 C1-C� 100

FB24 6.3 x 150 C1-C� 100

FB25 6.3 x 175 C1-C� 100

FB61 6.3 x 19 C4 • �50

Stainless steel self-tapping screw for pre-drilled holes, intended for mounting in thick steel/beams with material thickness 3-�5 mm. See installation instructions for choice of drill diameter. Long dimensions are suitable for external mounting of sandwich panels in steel beams.

FB62 6.3 x �5 C4 • �50

FB63 6.3 x 38 C4 • �50

FB66 6.3 x 75 C4 • 150

FB70 6.3 x 100 C4 • 100

FB73 6.3 x 130 C4 • 100

FB74 6.3 x 150 C4 • 100

FB75 6.3 x 175 C4 • 100

FB76 6.3 x �00 C4 • 100

FB77 6.3 x ��0 C4 • 100

FB79 6.3 x �60 C4 • 100

Unitap

Page 21: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

�1

Lindab Coverl ine | Fasteners

Self-tapping, Type C (AB)

Technical data

Screws for construction

Designation DimensionCorrosivity

classStainless

steelQuantity/

packArea of application

FC11 6.3 x 19 C1-C� �50

Self-tapping screw for pre-drilled holes, intended for mounting in lightweight steel constructions/profiles with material thickness 1.5-3.0 mm. See installation instructions for choice of drill diameter. Long dimensions are suitable for mounting sandwich panels in lightweight steel constructions.

FC12 6.3 x �5 C1-C� �50

FC13 6.3 x 38 C1-C� �50

FC14 6.3 x 51 C1-C� �00

FC15 6.3 x 64 C1-C� 150

FC16 6.3 x 75 C1-C� 150

FC20 6.3 x 100 C1-C� 100

FC22 6.3 x 130 C1-C� 100

FC25 6.3 x 175 C1-C� 100

FC50 4.8 x 16 C4 • �50

FC52 4.8 x �5 C4 • �50

Stainless steel self-tapping screw for pre-drilled holes, intended for external mounting in lightweight steel constructions/profiles with material thickness 1.5-3.0 mm. See installation instructions for choice of drill diameter. Long dimensions are suitable for external mounting of sandwich panels in lightweight steel constructions.

FC53 4.8 x 38 C4 • �50

FC54 4.8 x 51 C4 • �50

FC61 6.3 x 19 C4 • �50

FC62 6.3 x �5 C4 • �50

FC63 6.3 x 38 C4 • �50

FC64 6.3 x 51 C4 • �00

FC65 6.3 x 64 C4 • 150

FC66 6.3 x 75 C4 • 150

FC70 6.3 x 100 C4 • 100

FC73 6.3 x 130 C4 • 100

FC74 6.3 x 150 C4 • 100

FC75 6.3 x 175 C4 • 100

FC76 6.3 x �00 C4 • 100

FC77 6.3 x ��0 C4 • 100

FC79 6.3 x �60 C4 • 100

FC 91 7.� x 19 C4 • 100Stainless steel self-tapping screws for repairing damaged holes.

Unitap

Page 22: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

��

Lindab Coverl ine | Fasteners

Roof insulation to metal-plate and profiles.

Technical data

Screws for construction

DesignationDimen-

sionDrilling

capacityCorrosivity

classStainless

steelQuantity/

packArea of application

Roof insulation to metal-plate and profiles, countersunk head, sharp point

G12 4.8 x 60 0.6-0.9 C� 500

Insulation screw with sharp point and countersunk head. Intended for securing insulation to high profiles. The screw length minus approximately 10 mm gives the max clamp length.

G14 4.8 x 80 0.6-0.9 C� 500

G16 4.8 x 100 0.6-0.9 C� 500

G18 4.8 x 1�0 0.6-0.9 C� 500

G20 4.8 x 140 0.6-0.9 C� 500

G22 4.8 x 160 0.6-0.9 C� 500

G24 4.8 x 180 0.6-0.9 C� 500

G26 4.8 x �00 0.6-0.9 C� 500

G27 4.8 x ��0 0.6-0.9 C� 500

G28 4.8 x �40 0.6-0.9 C� 500

G29 4.8 x �60 0.6-0.9 C� 500

G30 4.8 x �80 0.6-0.9 C� 500

Roof insulation to metal-plate and profiles, countersunk head, drill tip

G39 4.8 x 60 0.7 - � x 1.�5 C� 500

Insulation screw with drill tip and countersunk head. Suitable for mounting hat profiles and rails to high profiles, also for insulation. The screw length minus approxi-mately 15 mm gives the max clamp length.

G40 4.8 x 80 0.7 - � x 1.�5 C� 500

G41 4.8 x 100 0.7 - � x 1.�5 C� 500

G42 4.8 x 130 0.7 - � x 1.�5 C� 500

G43 4.8 x 150 0.7 - � x 1.�5 C� 500

G44 4.8 x 180 0.7 - � x 1.�5 C� 500

G45 4.8 x �00 0.7 - � x 1.�5 C� 500

Roof insulation to metal-plate and profiles, countersunk head, drill tip, stainless steel

G61 4.8 x 60 0.7 - � x 1.�5 C4 • �50 Stainless steel insulation screw for mounting when there are stringent demands for corrosivity resistance. Supplied with reduced drill tip and countersunk head. Screw length minus approximately 15 mm gives max clamp length.

G62 4.8 x 80 0.7 - � x 1.�5 C4 • �50

G63 4.8 x 100 0.7 - � x 1.�5 C4 • �50

G64 4.8 x 1�0 0.7 - � x 1.�5 C4 • �50

G65 4.8 x 140 0.7 - � x 1.�5 C4 • �50

Washer for ISO screw

G48 40 mm - C� �50

G49 80 mm - C� �50

U-nite ISOscrew

Page 23: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

�3

Lindab Coverl ine | Fasteners

Wood to steel construction, profile.

Technical data

Screws for construction

DesignationDimen-

sionDrilling

capacityClamp length

Corrosivity class

Stainless steel

Quantity/pack

Area of application

Wood to light section steel

H21 4.8 x �5 1.� - � x �.0 13 C� �50

Fastening wooden battensand joists to light section steel.

H22 4.8 x 4� 1.� - � x �.0 30 C� �50

H23 4.8 x 60 1.� - � x �.0 48 C� �00

H24 4.8 x 70 1.� - � x �.0 58 C� �00

H32 5.5 x 45 1.5 - � x �.5 30 C� �50

H33 5.5 x 55 1.5 - � x �.5 40 C� �00

H34 5.5 x 70 1.5 - � x �.5 55 C� �00

H35 5.5 x 85 1.5 - � x �.5 70 C� �00

H37 5.5 x 109 1.5 - � x �.5 94 C� 100

H52 4.8 x 38 1.5 - � x �.5 �6 C4 • �50 Stainless steel screw for outdoor use in light section steel.H53 4.8 x 50 1.5 - � x �.5 38 C4 • �50

Wood to heavy section steel

H63 5.5 x 60 5.0 - 1�.5 �5 C1 �00

Fastening wooden battensand joists to heavy section steel.

H65 5.5 x 85 5.0 - 1�.5 50 C1 �00

H67 5.5 x 109 5.0 - 1�.5 75 C1 100

H35-H37

H�1-H34H5�-H53

Uniwing

Page 24: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

�4

Lindab Coverl ine | Fasteners

DesignationDimen-

sionHole

diameter Corrosivity

classStainless

steelQuantity/

packArea of application

Concrete screw, wood and steel joists to concrete

K11 4.8 x 3� 4 C1 �50Concrete screw for mounting steel profiles and wood in concrete. Screws must be mounted at least �5 mm in the concrete. Drill hole depth at least 7 mm deeper than screw length in the concrete.

K12 4.8 x 45 4 C1 �50

K21 6.3 x 3� 5 C1 �50

K22 6.3 x 45 5 C1 �50

K23 6.3 x 55 5 C1 �00

K24 6.3 x 70 5 C1 150

K25 6.3 x 81 5 C1 100

Concrete anchor, wood and steel joists to concrete

K31 6.0 x 31 6.5 C1 �50 Concrete anchor for various purposes. Suitable for securing both steel and wood to concrete surfaces. In the concrete, drill hole diameter 6.5 mm at least 40 mm deep. In mounting components, 8-8.5 mm diameter. Fire-classified with S.P. no. 9� R1�314 A60, permitted load 1.0 Kn.

K32 6.0 x 38 6.5 C1 �50

K33 6.0 x 50 6.5 C1 �00

K34 6.0 x 63 6.5 C1 150

K35 6.0 x 75 6.5 C1 150

Wood and steel joists to concrete

U-nite concrete

Technical data

Screws for construction

Page 25: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

�5

Lindab Coverl ine | Fasteners

Drywall to wood and steel joists

Technical data

Screws for construction

DesignationDimen-

sionDrilling

capacitySurface

treatmentStainless

steelQuantity/

packArea of application

Drywall to wood and steel joists

L11 3.5 x �5 0.9 Phosphate 1000

Screw with sharp point for fastening drywall to wood and thin steel profiles.

L12 3.5 x 38 0.9 Phosphate 1000

L13 3.5 x 50 0.9 Phosphate 500

L21 3.5 x �5 0.9 Zinc 1000

L22 3.5 x 38 0.9 Zinc 1000

L23 3.5 x 50 0.9 Zinc 500

Drywall to steel joists

L31 3.5 x �5 �.5 Zinc 1000

Screw with drill point for fastening drywall to thin steel profiles.

L32 3.5 x 40 �.5 Zinc 1000

L33 3.5 x 48 �.5 Zinc 500

Drywall to wood joists

L41 3.9 x 30 – Zinc 1000

Screw with sharp point for fastening drywall to wood.

L42 3.9 x 41 – Zinc 500

L43 3.9 x 55 – Zinc 500

L44 3.9 x 78 – Zinc �50

Outdoor drywall or board to steel joist, stainless steel

L93

L93BAND

4.� x �80.56 - � x 1.5

C4 •

500

1000

Stainless steel screw for fastening outdoor drywall to steel joists. Satisfies the requirements in Hus-AMA. Non-countersunk head and pilot point that prevents damage to the drywall.Collated version for more rapid installation with automatic screwgun .

KL: 14 mm

U-nite drywall

Page 26: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

�6

Lindab Coverl ine | Fasteners

DesignationDimen-

sionQuantity/

packArea of application

M11 - 100For hanging mirrors, shelves, boards, signs and many other items on drywall.

M12 4.� x 35 100Screw intended for U-nite drywall anchor, M11.

Installation in drywall

Screws for construction

Position the screwdriver at the top of the drywall anchor.

Press against the drywall at the same time as turning the drywall anchor clock-wise until the head is flush with the wall.

Place the fixture over the drywall screw Ø 4.2 mm into the plaster anchor.

U-nite drywall anchor

Technical data

DesignationDimen-

sionQuantity/

packArea of application

M81 14 x 40 100 Frame sleeve and screw for adjustable fixing of window- and doorframes to light section steel.M92 7.0 x 35 100

M94 7/14 x 70 100Frame screw for adjustable fixing of window- and doorframes to wood.

Window and doorframes to wood and light section steel

Other products

U-nite frame fixings

Page 27: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

�7

Lindab Coverl ine | Fasteners

Pipe flashers

Technical data

Other products

Designation Base PipeQuantity/

packArea of application

N11 1�0 5 - 50 10

N12 160 44 - 8� 10

N13 195 6 - 1�7 10

N14 �35 75 - 160 5

N15 �75 108 - 190 5

N16 315 1�5 - �30 5

N17 365 150 - �80 5

N18 4�0 175 - 330 5

N19 650 �54 - 483 �

• Fits all metal-plate profiles

• Can be used for all types of pipe, steel, copper, PVC

• Watertight and dust-proof

• Easy to install on all types of surface, see installation instructions page 4

• Made of weather-resistant EPDM rubber

• Can cope with temperatures from -65°C to +100°C

• Colour black

Page 28: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

�8

Lindab Coverl ine | Fasteners

Designation Type Size Length Area of application

Magnetic socket

O11-42 Magnetic socket 1/4” 4�

Hexagonal socket with magnet

O11-65 Magnetic socket 1/4” 65

O13-42 Magnetic socket 8 4�

O13-65 Magnetic socket 8 65

O14-65 Magnetic socket 3/8” 65

Spring socket

O21-65 Spring socket 1/4” 65

Hexagonal socket with springO23-32 Spring socket 8 3�

O23-65 Spring socket 8 65

Socket with ball

O33-50 Socket with ball 8 50 Hexagonal socket with ball

Bits, square

O52-25 Square No. � �5

Bits for square and octagonal drive.

O52-49 Square No. � 49

O52-50 Square No. � 65

O52-65 Square No. � 65

O53-25 Square No. 3 �5

O53-49 Square No. 3 49

Bits, octagonal

O55-49 Octagonal No. � 49Bits for octagonal drive (double square).

O56-49 Octagonal No. 3 49

O56-65 Octagonal No. 3 65

Bits Phillips

O62-25 Phillips No. � �5

Bits for Phillips drive.O62-49 Phillips No. � 49

O63-25 Phillips No. 3 �5

O63-49 Phillips No. 3 49

Bits Torx

O70-25 Torx T15 �5

Bits for Torx drive.

O70-49 Torx T15 49

O70-100 Torx T15 100

O71-25 Torx T�0 �5

O71-49 Torx T�0 49

O72-25 Torx T�5 �5

O72-49 Torx T�5 49

Sockets & bits

Other products

Installation aids

Technical data

Sockets & bits continues on page 29

Page 29: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

�9

Lindab Coverl ine | Fasteners

Flashings to wood

DesignationDimen-

sionCorrosivity

classStainless

steelQuantity/

packArea of application

Tin nail

P11 �.5 x 30 C3 1000

Tin nail for fasteningflashings to wood.

P12 �.5 x 30 C4 Copper 1000

P13 �.5 x 30 C4 Stainless steel • 1000

Clasp nail

P21 3.5 x 30 C3 500

Clamp nail for fasteningprofiled metal-plate and flashings to wood.

P22 3.5 x 30 C4 Copper 500

P23 3.5 x 30 C4 Stainless steel • 500

P31 3.5 x 40 C3 �50

P32 3.5 x 40 C4 Copper �50

P33 3.5 x 40 C4 Stainless steel • �50

P41 3.5 x 50 C3 �50

P42 3.5 x 50 C4 Copper �50

P43 3.5 x 50 C4 Stainless steel • �50

U-nite nail

Technical data

Designation Type Size Length Area of application

Installation tool

O72K Torx T�5 70Installation tool for screw with dome head and Torx drive

O72-70 Torx T�5 70 Special bits for installation tool 07�K

Bits set with holder

O95 �0 pieces 20 piece bit set containing� x Torx T15-�5� x Torx T�0-�5� x Torx T�5-�5� x Phillips No �-�5� x Phillips No 3-�5� x Slotted 6 mm� x Square No �-�5� x Square No 3-�51 x Torx T15-701 x quick release bit holder1 x Magnetic socket 1/4” 1 x Spring socket 8mm

Other products

continued from page 28

Page 30: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

30

Lindab Coverl ine | Fasteners

U-nite blind rivets

Technical data

Industrial range

Designation Dimension Max grip Colour-RAL Head diameter Quantity/pack

Open blind rivet type AL/ST, aluminium rivet with dome head and steel mandrel

RA11 3.� x 6 3.5 6.5 1000

RA12 3.� x 8 5.5 6.5 1000

RA13 3.� x 10 7.5 6.5 1000

RA14 3.� x 1� 9.5 6.5 1000

RB11 4.0 x 8 4.5 8 1000

RB12 4.0 x 10 6.5 8 1000

RB13 4.0 x 1� 8.5 8 1000

RB14 4.0 x 14 10.5 8 500

RB15 4.0 x 16 1�.5 8 500

RB16 4.0 x 18 14.5 8 500

RB17 4.0 x �0 16.5 8 500

RC11 4.8 x 8 4.0 9.5 500

RC12 4.8 x 10 6.0 9.5 500

RC13 4.8 x 1� 8.0 9.5 500

RC14 4.8 x 14 10.0 9.5 500

RC15 4.8 x 16 1�.0 9.5 500

RC16 4.8 x 18 14.0 9.5 500

RC17 4.8 x �0 16.0 9.5 500

RA45 6.4 x �5 �0.0 13 500

Open blind rivet type AL/ST, painted aluminium rivet with dome head and steel mandrel

RA1201 3.� x 8 5.5 Black - 9011 6.5 �50, 1000

RA1211 3.� x 8 5.5 Red - 3009 6.5 �50

RA1214 3.� x 8 5.5 Brown - 8014 6.5 �50

RA1215 3.� x 8 5.5 Tile red - 8004 6.5 �50

RA1240 3.� x 8 5.5 White - 9010 6.5 �50, 1000

RB1101 4.0 x 8 4.5 Black - 9011 8 �50 ,1000

RB1111 4.0 x 8 4.5 Red - 3009 8 �50

RB1114 4.0 x 8 4.5 Brown - 8014 8 �50

RB1115 4.0 x 8 4.5 Tile red - 8004 8 �50

RB1140 4.0 x 8 4.5 White - 9010 8 �50 ,1000

RB1201 4.0 x 10 6.5 Black - 9011 8 �50

RB1240 4.0 x 10 6.5 White - 9010 8 �50

Other models, sizes and colours on request.

Page 31: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

31

Lindab Coverl ine | Fasteners

Designation Dimension Max grip Colour-RAL Head diameter Quantity/pack

Open blind rivet type AL/ST, aluminium rivet with extra large dome head and steel mandrel

RD12 4.0 x 10 6.5 1� 500

RD15 4.0 x 16 1�.5 1� 500

RD17 4.0 x �0 16.5 1� 500

RD32 4.8 x 10 6.0 14 500

RD33 4.8 x 1� 8.0 14 �50

Open blind rivet type TI, stainless steel rivet with dome head and stainless steel mandrel (A2)

RE11 3.� x 6 3.5 6.5 1000

RE12 3.� x 8 5.5 6.5 1000

RE13 3.� x 10 7.5 6.5 1000

RE14 3.� x 1� 9.5 6.5 1000

Sealed blind rivet type ALT, aluminium rivet with dome head and steel mandrel

RG12 3.� x 8 3.5 6 1000

RG13 3.� x 10 5.0 6 1000

RG14 3.� x 1� 8.0 6 1000

RG21 4.0 x 8 3.0 8 1000

RG22 4.0 x 10 5.0 8 1000

RG23 4.0 x 1� 7.5 8 500

RG31 4.8 x 8 3.5 9.5 500

RG32 4.8 x 10 5.0 9.5 500

RG33 4.8 x 1� 8.0 9.5 500

RG34 4.8 x 14 9.5 9.5 500

RG35 4.8 x 18 13.0 9.5 500

Sealed blind rivet type ALT, painted aluminium rivet with dome head and steel mandrel

RG2201 4.0 x 10 5.0 Black - 9011 8 �50

RG2215 4.0 x 10 5.0 Tile red - 8004 8 �50

RG2240 4.0 x 10 5.0 White - 9010 8 �50

Sealed blind rivet type ALT, stainless stell with dome head and stainless steel mandrel

RH12 3.� x 8 3.0 6 1000

RH13 3.� x 9.5 4.5 6 1000

RH22 4.0 x 9.5 4.5 8 500

Multigrip, ventilation, aluminium rivet with dome head and steel mandrel

RK12 3.� x 8 5.0 6.� 1000

RK14 3.� x 9.5 6.4 6.� 1000

RK16 3.� x 11 8.0 6.� 1000

RK22 4.0 x 9.5 6.0 8.� 1000

RK24 4.0 x 1�.5 9.0 8.� 1000

RK26 4.0 x 16.5 13.0 8.� 500

RK32 4.8 x 10 6.5 9.� 500

RK34 4.8 x 14 11.0 9.� 500

RK36 4.8 x 16.9 13.0 9.� 500

Multigrip, ventilation, painted aluminium rivet with dome head and steel mandrel

RK1201 3.� x 8 5.0 Black-9011 6.� 1000

RK1211 3.� x 8 5.0 Red-3009 6.� 1000

RK1214 3.� x 8 5.0 Brown-8014 6.� 1000

RK1215 3.� x 8 5.0 Tile red-8004 6.� 1000

RK1240 3.� x 8 5.0 White-9010 6.� 1000

Other models, sizes and colours on request.

Page 32: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

3�

Lindab Coverl ine | Fasteners

Designation Dimension Max grip Colour-RAL Head diameter Quantity/pack

Multigrip, ventilation, steel rivet with dome head and steel mandrel

RM12 3.� x 9.5 4.0 7.� 1000

RM22 4.0 x 11 5.0 8.1 1000

RM32 4.8 x 10 4.8 9.8 500

RM34 4.8 x 1�.7 6.3 9.8 500

Open blind rivet type ST/ST, steel rivet with dome head and steel mandrel

RN11 3.� x 6 3.5 6.5 1000

RN12 3.� x 8 5.5 6.5 1000

RN13 3.� x 10 7.5 6.5 1000

Open blind rivet type ST/ST, painted steel rivet with dome head and steel mandrel

RN1201 3.� x 8 5.5 Black-9011 6.5 1000

RN1211 3.� x 8 5.5 Red-3009 6.5 1000

RN1214 3.� x 8 5.5 Brown-8014 6.5 1000

RN1227 3.� x 8 5.5 Grey-7040 6.5 1000

RN1240 3.� x 8 5.5 White-9010 6.5 1000

Open blind rivet type CU/ST, painted steel rivet with dome head and steel mandrel

RP11 3.0 x 6 3.5 6.5 1000

RP12 3.0 x 8 5.5 6.5 1000

RP13 3.0 x 10 7.0 6.5 1000

RP14 3.0 x 1� 9.0 6.5 1000

Split rivet, with dome head and steel mandrel

RS21 4.0 x 10 6.0 8 1000

RS30 4.8 x 10 5.0 9.5 500

RS31 4.8 x 1� 7.0 9.5 500

Blind rivet pliers

RZ12 Standard For rivets diam. �.4-4.0 1

RZ22 With long shanks For rivets diam. 3.�-4.8 1

Other models, sizes and colours on request.

Page 33: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

33

Lindab Coverl ine | Fasteners

Unidrill

Technical data

Industrial range

DesignationDimen-

sionDrilling

capacityCorrosivity

classStainless

steelQuantity/

packArea of application

Drill screw, pan head

SA11 3.5 x 9.5 �.�5 C1 1000

Drill screw with dome head for various purposes. Has locking grooves for a secure mount. Suitable for industrial requirements.

Phillips drive no. �

SA13 3.5 x 16 �.�5 C1 1000

SB10 4.� x 9.5 �.75 C1 1000

SB11 4.� x 13 �.75 C1 1000

SB13 4.� x 19 �.75 C1 1000

SB14 4.� x �5 �.75 C1 1000

SC12 4.8 x 13 3.5 C1 1000

SC14 4.8 x 19 3.5 C1 1000

SD11 3.5 x 9.5 � x 0.9 C4 • 1000Stainless steel screw where high demands are stipulated as regards corrosion resistance class. Has locking grooves for a secure mount.

Phillips drive no. �

SE11 4.� x 9.5 � x 0.9 C4 • 1000

SE12 4.� x 13 � x 0.9 C4 • 1000

SE13 4.� x 13 3 C4 • 1000

SE14 4.� x 16 � x 0.9 C4 • 1000

SE15 4.� x 16 3 C4 • 1000

SH11 4.� x 9.5 � x 0.9 C4 • 1000 Stainless steel industrial screw where high demands are stipulated as regards corrosion resistance class. Dome head with internal octagon, outer diameter of the SH and SK series: 9.5 and 11 mm respectively. Double square drive no. �

SH12 4.� x 13 � x 0.9 C4 • 1000

SH13 4.� x 13 3.5 C4 • 1000

SH14 4.� x 16 � x 0.9 C4 • 1000

SH15 4.� x 16 3.5 C4 • 1000

SH18 4.� x �5 � x 0.9 C4 • 1000

SK12 4.8 x 19 4 C4 • 1000

Unidrill is also supplied in painted version.

SA11-SC14

SD11-SE15

SH11-SK1�

Page 34: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

34

Lindab Coverl ine | Fasteners

Metal-plate screw, ventilation ducts and construction

Univent

DesignationDimen-

sionDrilling

capacityCorrosivity

classStainless

steelQuantity/

packArea of application

U40 3.5 x 9.5 � x 1.0 C1 1000Drill screw with reduced point for joining thin material. Hexagon head 1/4” with Phillips drive no. �.Stainless steel variant for high demands as regards corrosion resistance. Hexagon head 1/4”.

U41 4.� x 9.5 � x 1.0 C1 1000

U42 4.� x 13 � x 1.0 C1 1000

U46 4.� x 30 � x 1.0 C1 500

U49 4.� x 60 � x 1.0 C1 �50

TG10 4.� x 9.5 � x 0.9 C4 • 1000

TG12 4.� x 13 � x 0.9 C4 • 1000

DesignationDimen-

sionDrilling

capacityCorrosivity

classStainless

steelQuantity/

packArea of application

Drill screw, hexagon head

TA10 3.5 x 9.5 �.�5 C1 1000

Drill screw with hexagon head for various purposes. Suitable for industrial requirements and interior construction.

3.5-4.� = 1/4” hex head4.8-6.3 = 8 mm hex head

TA11 3.5 x 13 �.�5 C1 1000

TA12 3.5 x 16 �.�5 C1 1000

TB11 4.� x 9.5 �.�5 C1 1000

TB12 4.� x 13 �.75 C1 1000

TB13 4.� x 16 �.75 C1 1000

TB14 4.� x 19 �.75 C1 1000

TB15 4.� x �5 �.75 C1 1000

TC11 4.8 x 16 3 C1 1000

TC12 4.8 x 19 3 C1 1000

TC13 4.8 x �5 3 C1 1000

TC14 4.8 x 38 3 C1 500

TD12 5.5 x 19 5 C1 500

B32 5.5 x �5 5 C1 �50

B42 6.3 x �5 � x 3 C1 �50

TG10 4.� x 9.5 � x 0.9 C4 • 1000

Stainless steel screw for mountingwith high demands as regards corrosion resistance.

4.� = 1/4” hex head4.8-6.3 = 8 mm hex head

TG12 4.� x 13 � x 0.9 C4 • 1000

TG13 4.� x 13 3.5 C4 • 1000

TG14 4.� x 16 � x 0.9 C4 • 1000

TG15 4.� x 16 3.5 C4 • 1000

TH12 4.8 x 16 4 C4 • 1000

TH13 4.8 x �0 4 C4 • 1000

TH14 4.8 x �5 4 C4 • 1000

TH16 4.8 x 40 4 C4 • 500

B71 5.5 x �0 4 C4 • �50

B73 5.5 x �5 4 C4 • �50

B82 6.3 x �5 � x 3 C4 • �50

Unidrill is also supplied in painted version.

TA11-TE1�

TG10-B8�

Page 35: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

35

Lindab Coverl ine | Fasteners

DesignationDimen-

sionDrilling

capacityCorrosivity

classQuantity/

packArea of application

U51 4.� x 9.5 � x 0.9 C1 1000

Drill screw with sharp point for joining thin metal-plate or metal-plate to wood. Used primarily within ventilation and construc-tion. (Indoor use)1/4” hex head + Chisel slot.

U52 4.� x 13 � x 0.9 C1 1000

U54 4.� x 19 � x 0.9 C1 1000

U55 4.� x �5 � x 0.9 C1 1000

U57 4.� x 38 � x 0.9 C1 500

U58 4.� x 50 � x 0.9 C1 �50

U59 4.� x 75 � x 0.9 C1 �50

Installation screws are also supplied in painted version.

Installation screw

Technical data

Industrial range

Unifix

Metal-plate screw, ventilation and construction

Unispeed

DesignationDimen-

sionDrilling

capacityCorrosivity

classStainless

steelQuantity/

packArea of application

Installation screw, wood and steel joists

V12 4.� x 13 0.9 C1 1000

Installation screws with sharp tips for mounting in wood and thin steel profiles. (Indoor use)Phillips drive no. �

V13 4.� x 16 0.9 C1 1000

V14 4.� x 19 0.9 C1 1000

V15 4.� x �5 0.9 C1 500

V16 4.� x 3� 0.9 C1 500

V18 4.� x 50 0.9 C1 500

Installation screw, steel joists

V22 4.� x 13 �.0 C1 1000

Installation screw with drill tip for mounting in thin steel profiles (Indoor use). Phillips drive no. �

V23 4.� x 16 �.0 C1 1000

V24 4.� x 19 �.0 C1 500

V25 4.� x �5 �.0 C1 500

V26 4.� x 3� �.0 C1 500

V27 4.� x 38 �.0 C1 500

Installation screw for wood joists, stainless steel

V31 4.� x 13 - C4 • 1000

Stainless steel installation screw for external mounting in timber. Phillips drive no. �

V32 4.� x �5 - C4 • 500

V33 4.� x 3� - C4 • 500

V34 4.� x 45 - C4 • 500

V35 4.� x 65 - C4 • 500

Page 36: Lindab Fasteners Technical Information Components Global/fasteners...Lindab Fasteners Technical Information Lindab Coverline TM Lindab Coverline | Fasteners Dimensioning Tolerances

Lindab Coverl ine | Technical Information Fasteners

Lindab Profile is a business area within the Lindab

Group that develops, manufactures, and markets

efficient, economical and aesthetic steel and sheet-

metal solutions for the building industry.

We offer everything from complete building systems to

individual building components for all types of housing,

as well as commercial and industrial buildings.

Lindab Profile is represented in over �5 countries

throughout Europe. Our head office is in Förslöv,

in the south of Sweden.

Art

no

1531

88

2007

-06-

21

SE-269 82 BåstadPhone +46 (0)431 850 00www.lindab.com

Lindab Profile