x-ray films - xraykamarul | just another … is x-ray film? x-ray film is a photographic receptor...
TRANSCRIPT
What Is X-ray Film?
X-ray film is a photographic receptor consisting ofphotographically active or radiation sensitive emulsioncoated on a thin sheet like material, which is responsibleto record the physical impression of an object by whichwe can get detail about the object.
2
Classification of the film
3
MEDICAL X-RAY FILM
double-coated
screen type non-screen type
single-coated
screen type non-screen type
General radiographic film
Dental filmKidney surgery filmRadiation monitoring film
Mammographic film
CRT filmCopying filmLaser filmSubtraction film
Drystar FlmDryview film
Direct Exposure Film
4
Used without intensifying screens
Used mainly for extremities, previously for mammography
Requires 10 – 100 times more the exposure dose
The emulsion is thicker than screen film
Renders excellent detail
Indirect Exposure Film
5
These films are used in conjunction with pairs of I.S. .
The latent image being produced mainly by light emissionfrom screen phosphors.
A wide range of different films are available both the blue-sensitive and green - sensitive .
CHARACTERISTICS DIRECT EXPOSURE FILM INDIRECT EXPOSURE FILM
Exposed with Only by x-rays Mainly by vissible light
Used Without Screen With screen
Emulsion layer Thick Thin
Image formation In deep superficialy
Processing time more less
Resolution more less
Characteristic curve No apparent shoulder region in useful density range
Shoulder region within useful density range
Screen artifact no May possible
Exposure dose more less
Used in Orbit and extremities radiography. Also inIndustrial Radiography
General radiography
Difference B/W Non Screen & Screen Film
Type Of Direct Exposure Film
7
A. Dental Film
B. Kidney Surgery Film
C. Radiation Monitoring Film
D. Industrial Film
Dental Film
8
Periapical Dental Film:Used for single or group of Teeth
Occlusal Dental Fiim:Imaging mandibles or maxillae
Bitewing Dental film:Demonstrating the crown
Kidney Surgery Film
9
This duplitized film non screen film is designed to enable toradiographic exposure of kidney .
Each packet contains two films ,one with a fast emulsion,the other slow.
10 CM
13 CM FOR RENAL VESSELS
Laser Film
10
A laser printer uses digital electronic signal from an imagingdevice.
It is high-contrast single-emulsion film with extremely finegrain, also known as IR film.
Laser film is a silver halide film sensitized red light(Panchromatic) or laser light, e.g., HN Laser Film, IR LaserFilm.
Films Used With Cathode Ray
Tube Or TV Monitor
11
These films are used with cathode ray tube camera andmulti-formatter.
The emulsions are orthochromatic of medium to highcontrast and made to match a wide variety of CRTphosphor.
The film sizes commonly used are 8” x 10”, 11”x14” and14”x17” .
contd...
12
Used in following modalities:
Ultrasound
Computerized tomography
Magnetic resonance imaging
Nuclear medicine
Digital subtraction imaging
Substraction film
13
A type of single emulsion film used with angiography
One type prepares a positive copy of the image
The other type enhances subject contrast and detail
Duplicating Film
It is used to duplicate the pre-existing film.
Duplicating film is a single emulsion film that is exposedto ultraviolet light or Visible light through existingradiograph to produce a copy.
Polaroid Film
14
It is made up of positive and negative film sheets with a podof jellified processing chemistry.
Used particularly in ultrasound imaging.
The latent image is formed in the silver halide emulsion ofthe negative sheet. And the positive image formed due tomigration of Ag ions from the negative sheet.
The Dry View Film
15
High quality silver based material coated.
The heat /laser light sensitive layer contains silver halide/silver behnate crystal.
DRYVIEW Film also a type of laser film having high-resolution,
It is infra red sensitive photothermographic film that needsno wet film processor.
The Drystar Film
16
Direct thermal printing Drystar dry imaging films aredesigned to produce the highest diagnostic grayscalehardcopies. These images can represent the same "look andfeel" as conventional x-ray film.
Blue base
Maximum optical density > 3.5
Daylight film loading (films are insensitive to light)
Shelf life: to be used min. 18 months from packaging date
Storage temperature: 5 - 25 °C
Relative humidity: 30 - 60%
Extended term storage: minimum 20 years
Spectral Sensitivity
Spectral sensitivity is therange of wavelength of theelectromagnetic radiationthat the film will respond.
PEAK SENSITIVITY is therange of wavelength inwhich the film will exhibitits highest response
CUT-OFF SENSITIVITY isthe range of wavelengthbeyond which the film is nolonger sensitive.
Film Construction
22
0.0004”
0.0005”
0.007”0.008
TOTAL FILM THICKNESS =0.008 INCH
Double –sided emulsion film
Contd…
2323
0.0004”
0.0005”
0.007”0.008
Anti –Halation /non curl backing
Single –sided emulsion film
Difference b/w Single Coated And
Double Coated X-ray Film
Characteristic Single coated Double coated
Emulsion layer One side Both side
Patient Radiation dose More Less
Noncurl back layer Present Absent
Radiographic detail More Less
Average gradient (G) Very less more
Parallax effect No yes
Contrast Less more
Radiographic Film Base
25
Initially X-RAY were taken on glass plates.
In 1918 cellulose nitrate bases film replaced glass,butdiscarded because of highly inflammable .
In 1920 cellulose tricetate or safety base was introduced.
Polyester base replaced cellulose tricetate in the 1960”s,
Now a days POLYETHYLENE TEREPHTHLATE RESIN areused.
FilmBase
.007”
Character Of Good Base Material.
26
structural support for fragile emulsion low light absorption flexible, thick, & strong
• processing• handling• viewbox insertion / removal abuse
dimensional stability• in processing• For archival
varying humidity NON -FLAMMABLE
Subbing Layer (Adhesive Layer)
28
Also called adhesive layer or Substratum layer.
Made of mixture of gelatin solution and solvent of filmbase.
It keeps emulsion layer and base adhered to each otherduring coating stage and processing.
When dye is added, it counteracts cross over effect.
Provides uniform surface over which the emulsion can becoated uniformly.
Emulsion Layer
29
Emulsion is the heart of radiographic film .
The X-RAY or Light from I.S. interact with the emulsion andtransfer information to the film.
It consists of a very homogeneous mixture of gelatin andsilver crystal.
In typical emulsion 90 to 99% is AgBr and about 1 to 10% AgI .
NOTE:
• The presence of AgI produce an emulsion of muchsensitivity than a pure AgBr emulsion.
• It also contains traces of sulfur(ALLYLTHIOUREA).
EmulsionLayers
contd…
30
Silver halide in a emulsion is in the form of small crystals.
Silver halide crystals may be tabular,globular,polyhedral,orirregular in shape.
Crystal size might vary from 1.0 –1.5 microns in dimeterwith about 6.3 x 1010 grains per centimeter of emulsion.
Grain Technology
31
Globular Grain:spherical in shape and has a biggervolume.Use for blue sensitive film.
Tabular Grain:Has a table –top like structure that providesbigger surface but smaller volume.
Advantages Of Tabular Grain
32
Increased RESOLUTION due to reduction in cross- over.
Reduction in silver coating weight.
Suitable for 45 s processing.
Grain Size And Distribution
33
GRAIN SIZE and DISTRIBUTION affects the following:
SPEED: The bigger the average grain size, the higher thespeed of the film.
CONTRAST: Affected by size distribution. The moreavailable in the film, the lower the contrast.
GRAININESS: Graininess is the apparent clumping of thecrystal as seen on the radiograph. The bigger the crystal,thehigher the graininess o f the film.
Binder
34
A binder is an ingredient used to bind together two or moreother materials in mixtures.
The common type of a binder which we can use is Gelatin.
Gelatin
35
Gelatin is used as the suspending medium and bindingagent for the silver halide particles.
It comes collagen fiber in which primary source are thecartilage, skin and the protein matrix (ossein) of bone ofanimals.
Why We Use Gelatin As Binder?
36
It is a medium in which SILVER NITRATE and SODIUMBROMIDE can react and the resulting AgBr get finely andevenly dispersed and remain suspended.
In warm state it can be easily spread on the film base.
On cooling, it sets firmly on the base as gel.
It is flexible and does not crack easily on bending.
It is optically transparent .
Gelatin does not react chemically with the silver halide .
It is porous so the processing chemicals can penetrate tothe silver halide crystals.
Some of the constituents in gelatin enhances the activity ofSilver bromide and some act as antifoggant.
contd…
37
It is the great advantage of the gelatin in which it can setits intermolecular space a/c to the condition of theenvironment, While processing, gelatin swells up in contactwith water, allows processing chemicals to enter the layerand react with the grains of emulsion, & On drying itregains its former state.
It is believed that gelatin reduces the tendency of reversalof reaction of Silver bromide after exposure
Making Of The Film Emulsion
38
The light sensitive layer of a film is termed the Emulsion. The preparation of emulsion is carried out in four stages:
Emulsification
Ripening
Washing
Digestion
Emulsification
39
Aqueous solution of Silver nitrate and Potassium bromide ismixed with warm solution of gelatin.
AgNO3 + KBr AgBr + KNO3
Insoluble Silver bromide (AgBr) remains suspended inviscous gelatin.
More rapid process of mixing results small grain size, thatresults narrow grain size distribution hence there is lowgraininess & better resolution.
Note:
More bromide is used to increase the negative chargebarrier that helps in development process.
Ripening
40
Emulsion is placed in certain temperature and more gelatinis mixed. Size of the grains and their even distribution isdetermined at this stage
Slow mixing with long ripening at high temp.=> Fast emulsion (with large grains)
Rapid mixing with short ripening at low temp.=> Slow emulsion (with fine grains)
Slow mixing with NH3 at low temp.=> Fast emulsion (with large grains)
Washing
41
After ripening, emulsion is chilled to form thick gel.
This gel is shredded.
It is washed with water that remove KNO3 and excess KBr bydiffusion process.
Digestion
42
Shredded and washed emulsion is re-heated to furtherincrease its sensitivity.
Re-heating also make the emulsion liquid and suitable tospread on the film base.
Supercoat (overcoat)
43
Protective layer of gelatin
Provides sturdiness to unexposed radiographic film.
Antistatic
Reduces damage from scratches, pressure, orcontamination during storage, handling and processing.
Supercoating
Few Additives
44
Preservative – Phenol as bacteriocide
Silver iodide – To extend sensitivity towards blue range.
Some dyes may extend Colour sensitivity further
Glycerin to make the emulsion pliable
Saponin – To make the emulsion receptive to the processingchemicals
Alcohol – To prevent frothing during coating
Coating The Film
45
Different layers of film are coated on the base material withrollers and squeezers.
The film lengths are then passed over chilled rollers so thatliquefied gelatinous layers settle and harden.
Then The film lengths are hung like festoons in an airconditioned room to dry.
Mechanical cutters cut The film lengths in sheets ofdesirable sizes.
Anti- Halation Layer
46
Halation : it is a phenomenon characterized by formation ofa diffuse image or halo around the proper image.
This occurs mainly in the single sided film.
Non-curling Layer
48
Preferred for single sided emulsion film.
This layer is not removed during development.
Adding A Dye To Base
49
These dyes cannot be removed during development.
Dye introduced in the base is carefully controlled because itincrease the density and may interrupt the transparency ofthe film.
Note-dye used in this should be complementary to theexposing light. e.g.,red dye is used for greeen sensitivefilm,yellow dye is used for blue sensitive film .
Cross Over Effect
50
It is a type of halation which occurs when film is used withintensifying screen.
Occurs only with double emulsion films and two screens.
Light from one screen expands in the form of a cone as itpasses through the screen and emulsion where a slightlyenlarged, less sharp image is formed.
contd
51
Special dyes incorporated in the emulsion
Colored subbing layer is used.
Addition of magenta dye also reduces cross over effect.
Irradiation
52
It is the sideway scattering of light within the crystal ofemulsion.
This contributes to unsharpness (blurring) of image.
How Film Records An Image
There are three steps
formation of subject contrast (Optical image)
Recording of latent image
Conversion of latent image into permanent image(processing)
53
The Latent Image
The latent image is the invisible change in the silver halide crystals.
The interaction between the photons and the silver halide crystals produces the latent image or manifest image on the emulsion layer.
This interaction is sometimes referred to as the photographic effect.
54
Formation Of Subject Contrast
Subject contrast:-the variation in intensity of x-ray beamafter passing the absorber.
Subject contrast depends upon atomic No., density,thickness of absorber and the energy of the x-ray beam.
Different intensity of beam react differently with thephotographic material of the film.
55
56
The shape and lattice structure of silver halide are notperfect.
It causes some imperfection which results in imagingproperty of crystals.
So the sensivity specks is that low energy centre of thecrystal which acts as rest house for the 1º electron anddevelopment centre for the 2º electron.
Sensitivity Speck
For the formation of sensitivity specks impurity, usually aSilver-gold Sulfide is introduced by chemical sensitizationat or near the surface.
contd
57
The image forming x-rays deposit energy by photoelectricinteraction with atoms of silver halide crystals.
Formation of latent image is given by Gurney-Mott theory
contd
58
-
+
SENSITIVITY SPECK
SILVER HALIDE CRYSTAL
INTERSTITIAL Ag ION
1. Photon Absorption
6. Ag Ion Migration
3. Ag Ion Migration
2. Electron Trapping
+
-
4. Photon Absorption
-+
+
5. Electron Trapping
-
Producing the Latent Image
60
Radiation interaction releases electrons.
Electrons migrate to the sensitivity center.
At the sensitivity center, atomic silver is formed byattracting an interstitial silver ion.
The process is repeated many times resulting in the build upof silver atoms.
The remaining silver halide is converted to silver duringprocessing.
The resulting silver grain is formed.
Silver halide that is not irradiated remain inactive. Theirradiated and non-irradiated silver halide produces thelatent image.
Conversion Of Latent Image Into
Visible Image
61
This step is also known asprocessing. There are 4step in this processing:
1. Development
2. Fixing
3. Washing
4. Drying
Characteristics To Be Considered
While Selecting Film:
62
Contrast
Speed
Crossover
Spectral matching
Bulk of purchase
Time of purchase
Care And Protection Of Film
Films should be protected from
Physical damage
Light
High temperature
High relative humidity
Harmful gases and fumes
X-rays and radioactive source
Fire and theft
63
Resolving Power Of Films
64
Ability of a photographic emulsion to record fine details
It is expressed as the number of line pairs per millimeterwhich can be distinguished in the image as separate entities
Factors affecting the resolution of an image are – Grain size,Processing, Diffusion of light inside the emulsion layer andModular transfer function
Line Pairs Per Millimeter
65
A black and a white line make a line pair
A test pattern of slits cut on a metal plate with gradualfineness is exposed, processed and evaluated undermagnification.
Radiographic emulsions show 8 – 20 LP/mm
Photographic Fast emulsions show 40 – 50 LP/mm
• Medium emulsions show 70 – 100 LP/mm
• Slow emulsions show over 1000 LP/mm
Handling And Storage Of
Radiographic Film
67
X-ray film is a sensitive radiation detector and it must be handled in an area free of radiation.
Film storage must be shielded.
The darkroom adjacent to the x-ray room must be shielded.
If film use is low more shielding may be required.
Handling And Storage Of
Radiographic Film
68
Improper handling of the film will result in poor image quality due to artifacts.
Avoid bending, creasing or otherwise rough handling the film. Avoid sharp objects contacting the film.
Hands must be clean and dry.
Avoid hand creams, lotions or water free hand cleaners.
Static electricity or a dirty processor can cause artifacts.
Artifacts must be avoided.
Handling And Storage Of
Radiographic Film
69
Heat and Humidity must be controlled. Film is sensitive to heat and humidity from the time it is manufactured until the time it is viewed.
Heat and humidity causes fog or a loss of contrast. Film should be stored at 20º C (68º F).
Humidity should be between 40% and 60%.
Handling And Storage Of
Radiographic Film
70
Light will expose the film. Film must be handled and stored in dark.
If low level diffuse light exposes the film, fog is increased.
Luminous watches, cell phone and darkroom light leaks should be avoided.
Bright light causes gross exposure.
Handling And Storage Of
Radiographic Film
71
Shelf life. All film is supplied in boxes with an expirationdate.
Most film is supplied in boxes of 100 sheets.
The oldest film in stock should always be used first.Rotation is important.
Expired will loose speed and contrast and have increasedfog.