performance evaluation of pearl millet thresher in …
TRANSCRIPT
1
PERFORMANCE EVALUATION OF PEARL MILLET THRESHER IN
GHANA
S. Atsu1, G.Y. Obeng2 and E. Mensah3
1,3Department of Agricultural Engineering
2Technology Consultancy Centre
Kwame Nkrumah University of Science and Technology
Kumasi, Ghana.
ABSTRACT
The threshing of millet to obtain clean grain is one of the most tedious operations in small-scale millet
processing, particularly in Africa. A prototype millet thresher was developed during the International
Development Design Summit (IDDS) 2008 and adapted for the threshing of millet grains in Ghana.
Studies were conducted on the effect of millet moisture content on the machine performance and grain
quality. Grain quality was evaluated for normal and abnormal germination. The performance of the
millet thresher was evaluated for its threshing efficiency and seed loss during threshing. From the study
results, threshing efficiency ranged from 87.25% to 89.18% at millet moisture content of 11.84% to 13.48%.
The value of seed loss of 1.47% to 3.3% was low due to the relatively high threshing efficiency of the
millet thresher. Higher grain germination after threshing was obtained with the millet thresher, and it
ranged from 72% to 92%. The threshed millet grains were free from stones and sand.
Keywords: Millet, threshing, clean grain, Ghana.
2
CHAPTER ONE
INTRODUCTION
1.1 Background
Millet is a staple grain for millions of Ghanaians and their families especially those
living in the northern parts of the country. 75% of the pearl millet grown in the northern
parts of Ghana is threshed manually, at about 4kg/hour by mortar and pestle or beating
(Boateng, 2008). Threshing is the removal of grains from the stalk or panicle. This is
usually done either manually or mechanically. Threshing of millet in Ghana and other
African countries is done manually by mostly women. It entails beating the millet heads
with sticks or clubs repeatedly until almost all the grains are detached from the heads.
The beating action may be done either on a mat, canvas or bare ground. In order to ease
grain collection after beating, sometimes the heads of millets may be stuffed into bags,
prior to beating (Silas, 2001). A faster, affordable threshing device could improve the
health and economics of millions of poor families relying on millet for food or sale.
Inefficient processing and traditional primitive techniques of hand threshing are the
cause of excessive postharvest grain losses. Much of the pearl millet threshing in rural
Africa in countries like Namibia is still done by slow manual pounding that consumes
up to 4 hours/day of women's time, and results in blisters and repetitive stress injuries.
For most of the time, the pearl millet is stored threshed, but not winnowed. A family
might rent a car to drive over their year's harvest of millet to thresh it. This cost around
US$15 (FAO, 1994). Alternatively, they might pound it by hand in a specially prepared
hole. In both cases, the grain gets mixed with grit and dirt. Women separate the grains
from the ears with a mortar and pestle, as it is needed for consumption or for marketing
purpose. These traditional methods are arduous and slow (10kg per woman-day) (FAO,
3
1996). Consequently, research has been conducted for some years on how to efficiently
mechanize small-scale threshing of millet in rural and peri-urban areas.
Millet grows on a panicle consisting of a stalk, florets, and grain as indicated in figure
1.1. The panicle has complex physical properties. The panicles vary in size over a factor
of 2 hence grinding damages the grain, twisting breaks the stalk and rubbing removes
florets from stalk. The mechanical threshing of other grains does not raise any special
problems - conventional grain threshers can be used with some modification such as
adjustment of cylinder speed, size of the slots in the cleaning screens etc. On the other
hand, the dense arrangements of spikelets on the rachis and the shape of the millet ears
(especially pearl millet) make mechanical threshing excessively difficult (IDDS, 2008).
Figure 1.1: A millet panicle consisting of a stalk (B), florets (1&2) and grain.
After being harvested millets may be stacked on the plot. This in-field storage method
results in a pre-drying of the millet panicles before threshing, the purpose of which is to
separate seeds from panicles. The traditional threshing of millet is generally made by
hand: bunches of panicles are beaten against a hard element (e.g. a wooden bar,
bamboo table or stone) or with a flail. The outputs ranges between 10g and 30kg of
4
grain per man-hour according to the variety of millet and the method applied (CGIAR,
2008). Grain losses amount to 1-2%, or up to 4% when threshing is performed
excessively late; some unthreshed grains can also be lost around the threshing area. In
many places in the northern parts of Ghana, the grain is pounded in a mortar with
pestle (Figure 1.2) or threshed by being trodden underfoot by humans or animals; the
output is 30kg to 50kg of grain per man-hour (Eliasu, 2008).
Figure 1.2: Manual pounding of millet in the northern region of Ghana
Figure 1.3: Millet farming community in the Northern regions.
5
1.2 Problem Statement
The project will evaluate the performance of a manually operated low-cost millet
thresher costing US$20 and suitable for local manufacture and sale in Ghana.
1.3 Justification
The performance evaluation of the MIT thresher will produce data that can be used to
redesign and adapt the thresher for millet varieties in Ghana. It will also provide data
that can potentially be used for producing cost effective and affordable threshers for
resource poor farmers in Ghana. The project will help draw the attention of policy
makers to the mechanisation of millet threshing in Ghana. It will also provide data that
can potentially be used for producing cost-effective and affordable threshers for poor
farmers in Ghana.
1.4 Objectives
The objectives of this project were, in summary, to:
1. Determine the threshing efficiency of the millet thresher
2. Determine the millet moisture content suitable for threshing.
3. Determine the percentage seed loss from the millet thresher.
4. Access the percentage germination of threshed millet seeds from the millet thresher.
5. Make recommendations to enhance the development and performance of the millet
thresher.
6
CHAPTER TWO
LITERATURE REVIEW
2.1 Introduction
Millet is a common name applied to at least five related members of the grass family
grown for their edible seeds. Some of the varieties are foxtail millet (Setaria italica), pearl
or cat-tail millet (Pennisetum typhoideum), Japanese barnyard millet (Echinochloa
frumentacea), raggee or finger millet (Eleusine coracana), and koda millet (Paspalum
scrobiculatum). Proso millet also known as common millet, broom corn millet, hog millet
or white millet (Panicum miliaceum) .Minor millets include: Barnyard millet (Echinochloa
spp.) Kodo millet (Paspalum scrobiculatum) Little millet (Panicum sumatrense) Guinea
millet (Brachiaria deflexa = Urochloa deflexa) Browntop millet (Urochloa ramosa = Brachiaria
ramosa = Panicum ramosum) (Crawford and Lee, 2003).
Pearl millet is a variety of millet which is a crop for human food. Pearl millet
(Pennisetum glaucum, or P. americanum) is grown widely in the tropics and subtropics in
regions of limited rainfall where there is a growing season of 90 to 120 days (BBC News,
2005). In Ghana early-maturing pearl millet is traditionally intercropped with
groundnut (Arachis hypogaea), sorghum (Sorghum bicolor) or late-maturing pearl millet.
Pearl millet grain is used in several traditional food preparations: thick porridge called
tô, a thin, fermented porridge called koko, and a deep-fried pancake called marsa. The
naked seeds are yellowish to whitish in colour and about the size of wheat grain (Appa,
et al, 1984).
The thrashing machine, or, in modern spelling, threshing machine (or simply thresher),
was a machine first invented by Scottish mechanical engineer Andrew Meikle for use in
agriculture. It was invented (c.1784) for the separation of grain from stalks and husks.
7
For thousands of years, grain was separated by hand with flails, and was very laborious
and time consuming. Mechanization of this process took much of the drudgery out of
farm labour. (Wikipedia, 2006).
The first millet and sorghum threshers were developed in Africa in the 1960-70s: the
Siscoma BS 1000 and the Marot DAK II. Giving relatively high outputs (about 1000kg
per hour) they have been intended for village farmers' groups, cooperatives or private
contractors going from village to village to work on big threshing layouts (FAO,1994).
The multipurpose "Bamba" thresher, better suited to rural communities, has a capacity
of about 300kg per hour (FAO, 1994). As regards mechanized harvesting at family level,
some hand-operated threshers (Champenois) were developed and tested
experimentally but they did not prove very successful. From a historical viewpoint,
threshing operations were mechanized earlier than harvesting methods, and were
studied throughout the 18th century. Two main types of stationary threshing machines
have been developed. The machines of Western design are known as 'through-flow'
threshers because stalks and ears pass through the machine (FAO, 1994). They consist of
a threshing device with pegs, teeth or loops, and (in more complex models) a cleaning-
winnowing mechanism based upon shakers, sieves and centrifugal fan ('Through-flow'
Thresher.). The capacities of the models from European manufacturers (e.g., Alvan
Blanch, Vicon, Borga) or tropical countries (Brazil, India, etc.) range from 500 to 2000kg
per hour ( Assennato et al,1994).
In the 1970s, IRRI (International Rice Research Institute) developed an axial flow
thresher which has been widely manufactured at local level. Such is the case in
Thailand where several thousands of these units have been put into use. They are
generally mounted on lorries and belong to contractors working about 500 hours per
year. In practice, the costs of machines and services vary from one country to another.
8
Compared with animal-drawn implements, powered harvesting and threshing
machines are difficult to manufacture. Research has been conducted into the design of
simplified equipment which can be manufactured locally, e.g. the IRRI and Votex
threshers (FAO, 1994).
Theoretically, local manufacturing offers various advantages such as reduced profit
margins to retailers and transport costs (100 kits in one container instead of 22 Votex
threshers, etc.), but also some drawbacks (quality of construction and employed
materials, adverse taxation and customs regulations, etc.). Supplied services are
generally paid for about a percentage of the harvested crop: 5 to 10% for threshing and
15 to 20% for combine harvesting (Baker, R. D., 2003).
In Mali, the cost of using the Votex thresher is estimated to be between 3 and 5% of the
grain produced. Harvesting is a labour-intensive operation but is less arduous than
threshing. Because most of the rural population consider threshing as a particularly
tedious operation (especially in the case of millet), grain producers accept the relatively
high cost of mechanical threshing (IDRC, 2001).
9
Figure 2.1: Votex thresher (CIRAD, 2008)
Figure 2.2: Japan Thresher (CIRAD, 2008)
The 'hold-on' thresher of Japanese design ( 'Hold on' thresher - Japanese design.), is so-
called because the bundles are held by a chain conveyor which carries them and
10
presents only the panicles to the threshing cylinder, keeping the straw out. According to
the condition of the crop, work rates can range between 300kg and 700kg per hour
(Iseki model). The main disadvantage of these machines is their fragility (FAO, 1994).
The pearl millet thresher developed during IDDS 2008 at MIT is an innovative,
inexpensive, portable threshing machine developed for small pearl millet farmers and
consumers (see Figure 2.3 below). It produces cleaner and healthier grain, faster, safer
and cheaper.
Figure 2.3: A prototype of pearl millet thresher developed during IDDS 2008
In developing countries like Ghana, harvesting and threshing operations are
traditionally carried out by women. However, in most situations, as these operations
become mechanized, they are taken over by men and the role of women is reduced to
winnowing and the gleaning of grain scattered during harvesting and threshing. The
mechanization of post-harvest operations frequently means the transfer of activities
from women to men (Korletey and Eliasu, 2008).
11
2.2 Threshing methods
The same method, but using a vehicle (tractor or lorry) is also commonly applied. The
vehicle is driven in circles over the paddy bunches as these are thrown on to the
threshing area (15m to 20m in diameter around the stack). The output is a few hundred
kg per hour. This method results in some losses due to the grain being broken or buried
in the earth. In Ghana, total losses induced by traditional harvesting and threshing
methods are estimated between 5 and 15 % (Silas, 1996). Also other methods include the
use of the mortar and pestle.
2.3 Mechanised threshing
More recently, a Dutch company (Votex) has developed a small mobile thresher
provided with either one or two threshers (Figure 2.1). The machine has been widely
adopted in many rice growing areas. The simple design and work rates of these
machines (about 500kg per hour) seem to meet the requirements of rural communities.
(FAO, 1994)
2.4 Millet growth in Ghana
Pearl millet varieties namely, PARC MS-1, PARC MS-2, PARC MS-5 PARC MS-6,
Ghana White and ICMP 96491 have been proved high yielding dual purpose (grain-
cum-fodder) varieties. These varieties are drought resistant. These varieties have been
grown in Ghana over the years (Boateng, 2008). Figure 2.4 shows the trend in millet
production from 1990 to the year 2007 in Ghana. The data reveal an estimated current
production level of about 150, 000 metric tons.
12
Figure 2.4: Trend in Millet Production from 1990 to 2007 in Ghana.
13
CHAPTER THREE
MATERIALS AND METHODS
3.1 Experimental Site
The study was conducted at the Department of Agricultural Engineering at Kwame
Nkrumah University of Science and Technology, Kumasi.
3.2 Source and Variety of millet Obtained
Millet grain samples were obtained from farms in the Upper East region of Ghana. Test
samples were from the 2008 growing season.
Fig 3.1: Varieties of Millet Identified
14
3.3 Materials and Method
The millet thresher was developed at the Agricultural Engineering Workshop. A
recycled bicycle was use in the development of the thresher. To thresh the millet, a stalk
is placed on the rim of the thresher and the pedal rotated anticlockwise due to the fact
that, the bicycle which is being used for the threshing has been turned upside down.
During the rotation of the rim the millet stalk which is being threshed is also rotated
gently in order for the spokes to thresh all the grains on the stalk. The moisture content
of the millet before threshing, the spokes clearance and the speed of the rotating rim
played important roles in the determination of the efficiency of the thresher. Before
threshing the mass of millet stalks to be threshed were weighed using an electronic
balance. After threshing, the threshed millet, the chaff and the stalk was weighed.
3.4 Determination of Total Losses
The following relationships were used to calculate the total losses of the thresher.
(a) Percentage of unthreshed seeds =
100 quantity of unthreshed seeds obtained from all outlet in kg
Total grain input in kg (1)
(b) Percentage of cracked and broken seeds =
100 (cracked and broken seeds from specified seed out let (s) in kg
Total seeds received at seed outlet in kg (2)
(c) Percentage of blown seeds =
100 (quantity of clean seed obtained at chaff outlet in kg )
Total grain input in kg (3)
Total Loss (%) = sum of losses obtained at (a), (b) and (c) (4)
15
3.5 Determination of efficiencies
(i). Threshing efficiency = 100 - Percentage of unthreshed seeds
3.6 Germination Test
Two pearl millet varieties were used in the determination of the percentage seed
germination of the threshed millet from the thresher which will aid in determining the
seed quality produced by the millet thresher. 100 seeds were counted from the threshed
millet and 10 rows of 10 seeds were planted because the rows make it easier to count
seedlings. Seeds were sown at normal seeding depth of 2-3 cm. The seeds were placed
on top of the sand or soil and pushed in with a piece of dowel or a pencil and then
covered with a little more sand, it was then gently watered or kept moist (not wet)
because over-watering will result in fungal growth on the seeds, causing possible seed
rot and hence affecting normal germination. Keep moist. Seedlings were counted after 7
to 10 days when the majority of seedlings are up. Late seedlings that germinated were
not counted because they were the weak and damaged seeds. Only normal seedlings
were counted. Badly diseased, discoloured or distorted seedlings were not counted.
Percentage germination was calculated as;
Percentage germination = number of germinated seeds x 100%
Total number of seeds planted
3.6.1 Paper substrate germination test
In the determination of the viability of the threshed grain, 10 seeds were counted from
each variety and the planted in a paper substrate under laboratory conditions at 20ᵒc.
The paper substrate was placed in a Petri dish and a water bottle was used to keep the
16
substrate moist. The seeds were then planted in the paper substrate. It was then covered
with another Petri dish. The set up was monitored for 7days. The germinated seeds
were then counted. The number of germinated seeds counted was used to determine
the percentage germination. Due to over watering the grey variety was affected by
fungal infection hence the inability of the seeds to germinate.
3.7 Determination of moisture content
Seed moisture content is one of the most important factors influencing seed quality and
storability, therefore, its estimation during seed quality determination is important.
Seed moisture content can be expressed either on wet weight basis or on dry weight
basis. In seed testing, it is always expressed on a wet weight basis; the method for its
calculation is given later. For the purpose of this experiment, seed moisture content was
determined by air oven method or gravimetric method.
In this method, the seed moisture was removed by drying at a specified temperature
(103ᵒC) for a specified duration (17h). The moisture content was then expressed as a
percentage of the original weight (wet weight basis). The percentage moisture content
was then calculated as follows:
Percentage moisture content = Loss in weight ×100
Initial weight of seed
17
CHAPTER 4
RESULTS AND DISCUSSIONS
4.1 Results
4.1.1 Moisture Content Determination
Table 4.1: Moisture content determination table
Container
Identification
Weight of
empty
container
(g)
Weight of
sample
and
container
(before
drying)
(g)
Weight of
sample
before
drying
(g)
Weight of
sample
and
container
after
drying
(g)
Weight
loss
(g)
% Moisture
M1 M2 M2-M1 M3 M2-M3 100
12
32
MM
MM
REPLICATE 1
YELLOW 32.87 96.69 63.82 88.31 8.38 13.13
GREY 77.17 148.50 71.3 139.71 8.79 12.33
STALK
YELOW 402.38 507.90 105.52 494.53 13.37 12.6
GREY 57.36 136.04 78.68 126.70 9.34 11.87
WHITE 26.74 160.03 133.29 144.10 15.93 11.95
BLK&WHT 25.65 107.13 81.48 97.48 9.65 11.84
RED 32.39 95.22 62.83 86.75 8.47 13.48
18
Container
Identification
Weight of
empty
container
(g)
Weight of
sample
and
container
(before
drying)
(g)
Weight of
sample before
drying
(g)
Weight of
sample
and
container
after
drying
(g)
Weight
loss
(g)
% Moisture
M1 M2 M2-M1 M3 M2-M3 100
12
32
MM
MM
REPLICATE 2
YELLOW 32.87 115.83 82.96 106.57 10.86 13.09
GREY 26.74 98.32 71.58 88.93 9.39 13.12
REPLICATE 3
YELLOW 89.10 154.15 65.05 145.47 8.68 13.34
GREY 89.10 149.02 59.92 141.11 7.91 13.20
REPLICATE 4
YELLOW 454.73 482.82 28.09 479.13 3.69 13.14
GREY 454.73 510.70 55.97 503.27 7.43 13.27
Average moisture content of samples
Yellow variety = 4
%14.13%34.13%09.13%13.13 = 13.18%
Grey variety = 4
%27.13%20.13%12.13%33.12 = 12.98%
19
Table 4.2: Weight of Parameters Obtained after Threshing for the Various Varieties
After Threshing
Yellow Variety Grey Variety
Parameters
Weight of Stalks before threshing (A) 302.86g 492.25g
Weight of Stalks after threshing (B) 98.20g 103.01g
Weight of Grain (C = A- B) 204.66g 389.24g
Weight of empty container (D) 77.18g 77.14g
Weight of empty container + threshed grains (E) 254.77g 418.74g
Weight of threshed grain (F = E - D) 177.59g 341.60g
Weight of unthreshed grain 22.15g 39.56g
Table 4.3: Weight of Parameters Obtained after Winnowing for the Various Varieties
After Winnowing (Cleaning)
Yellow Variety Grey Variety
Parameters
Weight of empty container (A) 32.38g 77.14g
Weight of empty container + chaff (B) 82.31g 108.19g
Weight of empty container + clean grains (C) 157.13g 387.67g
Weight of chaff and clean grains (D = B - A) 49.93g 31.05g
Weight of clean grains (E = C - A) 124.75g 310.53g
20
Yellow Variety
Percentage of unthreshed seeds = %10066.204
15.22 = 10.82%
Percentage of broken or cracked seeds = %10072.124
62.5 = 4.51%
Threshing efficiency = 100%- 10.82% = 89.18%
Grey Variety
Percentage of unthreshed = %10053.310
56.39
g
g = 12.75%
Threshing efficiency = 100% - 12.75% = 87.25%
Percentage broken seeds = %10053.310
56.4 = 1.47%
21
4.1.2 Germination Test
Total number of seeds planted in the soil = 100
Yellow Variety
Table 4.4: Germination test results for yellow variety
Sample Number of seeds germinated percentage germination
A 38 76%
B 34 68%
Average % germination 72%
Grey Variety
Table 4.5: Germination test results for grey variety
Sample Number of seeds germinated Percentage germination
A 47 94%
B 45 90%
Average % germination 92%
4.1.3: Paper substrate method
Grey Variety
Number of seeds planted in paper substrate = 10
Number of seeds germinated =8
Therefore percentage germination = 80%
22
Yellow Variety
Number of seeds planted in paper substrate = 10
Number of seeds germinated =0
Therefore percentage germination =0%
4.1.4: Speed Test
Table 4.6: Shows the Various Speed Test and their Efficiency with Time
Weight of stalk
before
threshing
Weight of
stalk after
threshing
Weight of
threshed
grains
Speed
(rpm)
Time taken to
thresh
(min)
Efficiency
(%)
26.87g 10.52 16.35g 75 4 60.8
44.86g 22.71g 22.5g 110 7.5 50.1
37.18g 11.66g 25.52g 200 2.4 67.9
32.63 8.79 23.66g 325 3.59 72.5
24.33g 8.05g 16.28g 425 1.32 66.9
23
4.2 Discussion
4.2.1 Performance Evaluation
The millet thresher was installed on level and hard surface. Sufficient quantity of dried
two different varieties was taken. The threshing efficiency, percentage total loss and
germination were evaluated. During the test period, the speed of the rim was recorded
against the time of threshing and the percentage threshing efficiency using a
tachometer.
4.2.2 Threshing Efficiency and Moisture Content
The threshing efficiency ranged from 87.25% to 89.18% for the spokes clearance of 6mm
to 8mm and 11.84% to 13.48% moisture content for both varieties of the millet. This was
obtained at average speed between 200rpm and 325rpm, from table 4.6. The threshing
efficiency for a given level of spokes clearance and moisture content increases with
increase in rim speed. At given moisture content and rim speed to about 325rpm the
efficiency increases and then begins to drop in efficiency to a speed of 400rpm and
above. The threshing efficiency increases with increase in spokes clearance between
6mm to 8mm. This is however not the case with increase in rim speed for a given
moisture content where the threshing efficiency reduces. This is due to the increased
impact on the grains in the stalk resulting in a low ability of the thresher to efficiently
thresh the stalks thereby resulting in low threshing efficiency and causing most of the
seeds to be lost in the chaff.
4.2.3 Total Loss (%)
The total loss as spilled over and blown-up seeds ranged from a minimum of 3.3% to
maximum of 13.1% for the spokes clearance of 6mm to 8mm and moisture content of
24
11.87% to 13.48% respectively. The total losses were influenced significantly by the rim
speed, spokes clearance and moisture content. The total loss was the least at the average
rim speed of 200rpm to 325rpm and increased with increase in speed. Generally, the
spokes clearance of 6mm caused the minimum total loss at a given moisture and speed.
The percentage of cracked or broken seeds observed was minimum between1.47%
and4.51%.
4.2.4 Germination
The percentage germination of threshed seed was influenced significantly by moisture
content, rim speed and spokes clearance. The germination of the threshed seed ranged
from 72% to 92% over the range of spokes clearance 6mm to 8mm and 11.84% to 13.48%
moisture content.
The percentage germination of the threshed seed reduced with increase in rim speed.
The germination of threshed seed at 11.84% moisture content was significantly less at
the corresponding levels of speed and spokes clearance compared to germination of
seed threshed at 13.13% moisture content. Also, the minimum spokes clearance of 6mm
caused the minimum reduction in percentage germination. Increase in cylinder speed
causes higher damage while lower spokes clearance reduces the damage. Also the
higher the moisture content the more susceptible the seed is to deformation without
breakage resulting in injury or viability of seed. Therefore, the observation of reduction
in germination with increase in rim speed, moisture content and increase of spokes
clearance could be expected. Due to fungal infection on the grey varieties during the
paper substrate germination test all the seeds planted did not germinate as compared to
the yellow variety.
25
CHAPTER 5
CONCLUSIONS AND RECOMMENDATIONS
5.1 Conclusions and Recommendations
The main conclusions and recommendations arising out of the study are as follows:
1. The performance of the millet thresher was high and was affected by the moisture
content and the rim speed.
2. The optimum threshing efficiency of 89.18% was obtained using the average speed
between 200 rpm and 325 rpm at moisture content of about 13%.
3. The germination of the threshed seeds was high implying that the thresher did not
cause internal damage to the seeds.
4. The grains that were produced were free from stones and sand as compared to those
threshed in the rural areas.
5. Increase in the number of spikes in the threshing head from 27 to 36 in order to
increase the force of impact by the spikes on the material; thus increasing the threshing
efficiency.
6. There is the need to design an appropriate threshing chamber to facilitate the
collection of threshed grains.
7. There can be viable enterprises manufacturing and selling the millet thresher after it
has been continuously perfected and scaled-up as a marketable product.
26
REFERENCES
Agricultural Research Corporation ARC Sudan. (Accessed 3/30/06)
(http://www.arcsudan.org/millet.htm) Millet Research Program
Appa Rao S., Melak H. Mengesha and Sharma D. (1984). Collection and evaluation of
pearl millet (Pennisetum americanum) Germplasm from Ghana Genetic resource unit
ICRISAT and GTZ, Ghana.
Baker, R. D., (2003). Millet Production (Guide A-414) [PDF], New Mexico State
University
BBC News (2005) "Oldest noodles unearthed in China", (12 October 2005).
Boateng, (2008) Grains and Legumes Development Board, MoFA. Personal
Communication
CGIAR, 2008. Areas of Research: Millet Research & Impact. Consultative Group on
International Agricultural Research (CGIAR).
Crawford, Gary W. and Gyoung-Ah Lee. (2003) Agricultural Origins in the Korean
Peninsula. Antiquity 77(295):pp87-95.
FAO (1994). Grains storage techniques: Evolution and trends in development countries.
FAO Agricultural Services Bulletin No. 109.
IDDS (2008), Pearl millet thresher [www.millet.wetpaint.com]. Accessed December,
2008
27
IDRC (2001). Projects in Mali. Modified on 6th May 2009 [www.idrc.ca]. Accessed
December, 2008.
Korletey and Eliasu (2008) Ministry of Food and Agriculture. Personal Communication.
M. de Lucia and D. Assennato (1994) Agricultural Engineering in Development: Post
harvest operations and management of food grains. FAO Agricultural Services Bulletin
No. 93.
Silas T.A.R Kajuna (1996), MILLET: Post-harvest operations. Food and Agriculture
Organization.
Syngenta Foundation for Sustainable Agriculture (SFSA) (2008). Crops: Millet: What is
Millet?
Syngenta Foundation for Sustainable Agriculture.(SFSA) 2008, Crops: Millet: Pearl
Millet
Wikipedia contributors, 'Millet', Wikipedia, The Free Encyclopedia, 3 April 2006, 15:43
UTC, [accessed 3 April 2006].