performing bench work ppt
TRANSCRIPT
![Page 1: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/1.jpg)
Performing Bench work
Department of EMMTLevel I (summer program)
Module trainerLemma Kiftaga(BSc in Engineering)
![Page 2: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/2.jpg)
1. Introduction to engineering metals• We will group materials of similar types
together and discuss their properties
• Generally Materials can be classified :– metallic and ,non metallic material
• Metal:We can consider metals as substances that have a lustrous sheen when cut, are good conductors of heat, and are good conductors of electricity.eg. aluminum, copper and iron
• Non metal:These can be elements, compounds of elements and mixtures of compounds. They include wood, rubber, plastics, ceramics and glass.
![Page 3: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/3.jpg)
Continued …• Some materials are compounds of metals and
non-metals. eg, naturally occurring abrasive grits, such as corundum contain between 70% and 90% of aluminium oxide (a compound of aluminium and oxygen).
![Page 4: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/4.jpg)
1.1. Importance of metals
• Metal are the most important elements on earth that are mostly applicable in many industrial activities and construction sectors.
• A repair man repairs broken parts and manufactures replacements according to samples and blueprints.
![Page 5: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/5.jpg)
1.2 Classification of metals• Metals can be classified as ferrous and non
ferrous metals.
• Ferrous metals: Ferrous metals and alloys are based on the metal iron.
• Iron is a soft grey metal and is rarely found in the pure state outside a laboratory
• For engineering purposes the metal iron is usually associated with the non-metal carbon.
![Page 6: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/6.jpg)
Continued…i. Plain carbon steels:as their name implies,
mainly of iron with small quantities of carbon.
• There will also be traces of impurities left over from when the metallic iron was extracted for its mineral ore.
• A small amount of the metal manganese is added to counteract the effects of the impurities.
![Page 7: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/7.jpg)
Plain carbon steel Contains
0.1% to 1.4% carbon.
Up to 1.0% manganese (not to be confused with magnesium).
Up to 0.3% silicon.
Up to 0.05% sulphur.
Up to 0.05% phosphorus.
![Page 8: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/8.jpg)
Effect of carbon content on the properties of plain carbon steel
![Page 9: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/9.jpg)
plain carbon steels can be grouped in to categories
i. Low carbon steels
(below 0.3% carbon).
ii. Medium carbon steels
(0.3% to 0.8% carbon).
iii. High carbon steels
(between 0.8% and 1.4% carbon).
![Page 10: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/10.jpg)
i. Low carbon steels
• It is referred to as mild steels
• If the carbon content is kept between 0.1% and 0.15%, the steel is often referred to as ‘ dead mild ’ steel.
• This steel is very ductile and very soft, and can be pressed into complicated shapes for car body panels at room temperature without cracking
![Page 11: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/11.jpg)
Continued…• It is used for the sub-strate of tin-plate and galvanized
steel. It is slightly weaker than the next group of low carbon steels to be considered
• Mild steel can be forged, rolled and drawn both in the hot and in the cold condition. It is easily machined with high-speed steel cutting tools.
• Because of its ease of manufacture and the very large quantities produced, mild steels are the cheapest and most plentiful of the steel products.
• Hot worked mild steel is available as structural sections for fabrication engineering (e.g. I-section beams, rolled steel joists, reinforcing rods and mesh for concrete, etc.), forgings, sheet, strip, plate, rods, bars and seam-welded tubes.
![Page 12: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/12.jpg)
Cold worked mild steel
• also known as bright drawn mild steel is available as
bright drawn bars
rods
solid drawn tubes
sheet and strip
formed wire goods.
![Page 13: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/13.jpg)
Medium carbon steels• There are two groups of medium carbon steels
From 0.3% to 0.5% carbon(can be heat treated to make them tough and strong)
From 0.5% to 0.8% carbon can be heat treated to make them fairly hard yet remain a degree of toughness (impact resistance).
• Medium carbon steels are harder, stronger and tougher than low carbon steels.
• They are also more expensive. They cannot be bent or formed in the cold condition to the same extent as low carbon steels without cracking.
![Page 14: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/14.jpg)
Continued…• medium carbon steels hot forge well, but
close temperature control is required to prevent(burning and cracking)
Burning’ at high temperatures over 1150°C, as this leads to embrittlement. The metal cannot be reclaimed and the forging has to be scrapped.
Cracking when forging is continued below 700°C. Cracking is due to work hardening as the steel is in the ‘cold’ condition from a forging point of view.
![Page 15: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/15.jpg)
Continued…• Medium carbon steels with carbon content in the
0.3% to 0.5% range are used for such products as drop-hammer die blocks, laminated springs, wire ropes, screwdriver blades, spanners, hammer heads and heavy duty forgings.
• Medium carbon steels with carbon content in the 0.5% to 0.8% range are used for such products as wood saws, cold chisels, forged blanks for connecting rods, crankshafts, gears and other stressed components such as high- ensile pipes and tubes.
![Page 16: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/16.jpg)
High carbon steels• These are harder, less ductile and more expensive
than both mild and medium carbon steels.
• They are also less tough
• used for springs, cutting tools and forming dies.
• High carbon steels work-harden readily and, for this reason, they are not recommended for cold working.
![Page 17: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/17.jpg)
Groups of high carbon steels
i. From 0.8% to 1.0% carbon where both toughness and hardness are required.
sheet metal pressing tools where the number of components to be produced does not warrant the cost of expensive alloy steels.
Also, cold chisels for fine work, some hand tools, shear blades, coil springs and high-tensile wire (piano wire).
![Page 18: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/18.jpg)
Continued…ii. From 1.0% to 1.2% carbon for sufficient hardness for most metal cutting tools for example wood-drills, screw-cutting taps and screw-cutting dies.
iii. From 1.2% to 1.4% carbons where extreme hardness is required for wood-working tools and knives where a very keen cutting edge is required. For all of these applications the steel has to be heat-treated to enhance its properties
![Page 19: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/19.jpg)
Properties of material
• Physical properties
• Chemical properties
• Thermal properties
• Electrical properties
• Magnetic properties
• Optical properties, and
• Mechanical properties
![Page 20: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/20.jpg)
Layout• Selection of Materials: depends on the specific
task to be performed.
• Layout tool: Before you can shape or form work pieces, you have to mark them to the required dimensions.
• The following tools are used in laying-out.
![Page 21: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/21.jpg)
scriber
![Page 22: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/22.jpg)
Continued…
![Page 23: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/23.jpg)
Continued…
![Page 24: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/24.jpg)
Dot punch…
a. making out punches, b. making out dots , c. filling of removing metal, d. chamfering
![Page 25: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/25.jpg)
The procedure making punched hole1.Mark out the centre.
2. Centre punches using the punch and a hammer
a) finding the position of the hole (b) punching (c) punched hole.
![Page 26: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/26.jpg)
![Page 27: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/27.jpg)
![Page 28: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/28.jpg)
![Page 29: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/29.jpg)
![Page 30: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/30.jpg)
![Page 31: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/31.jpg)
![Page 32: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/32.jpg)
3. Bench work operations3.1 Cutting: In the metalwork shop, materials (especially metals) are cut to shape before filing. The numerous types of cutting operations.
Cutting using Saws(mishar) :Saws used for cutting purposes in the school workshop
The different type of saw are:
• Hacksaw
• The junior hacksaw
• The sheet saw
• The piercing saw
![Page 33: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/33.jpg)
![Page 34: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/34.jpg)
types of saw• Hacksaw
![Page 35: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/35.jpg)
Points to watch when using the hacksaw1. Hold the work securely in the vice.
2. Grip the hacksaw firmly, using both hands
3. Use the same stance as for filing.
4. Use the full length of the blade.
![Page 36: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/36.jpg)
Other saws…• The junior hacksaw: has a spring tension frame,
which takes a blade about 150 mm long and 6 mm wide. It is useful tool for small work.
• The sheet saw: is used for cutting large sheets of metal or other materials, and fitted with the standard hacksaw blade (32 teeth per 25mm).
• The piercing saw: is used for fine work, either for decorative patterns or for cutting circles in beaten metal work. To fix the blade, loosen one end and passing through a hole drilled in the work, then re-fix it in the frame.
![Page 37: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/37.jpg)
KNIVES(mindi)• Most knives have cutting edges and are used to
cut, pare, notch, and trim wood, leather, rubber, and other materials.
Fig. Pocket Knife
![Page 38: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/38.jpg)
Saddler knife
![Page 39: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/39.jpg)
Rubber cutting knife
![Page 40: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/40.jpg)
Putty knife
![Page 41: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/41.jpg)
PIPE CUTTING• There are two sizes of pipe cutters.
• One size can cut from 1/8 to 2 inches
• while the other can cut from 2 to 4 inches. The pipe cutter has
1. a cutting blade
2. two pressure rollers which are adjusted and tightened by turning the handle
• Pipe cutters are used to cut steel, brass, copper, wrought iron, and lead pipe.
![Page 42: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/42.jpg)
Continued…
![Page 43: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/43.jpg)
Procedures to cut pipe• Measure from end of pipe and make a mark
where you want to cut
![Page 44: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/44.jpg)
Continued…
• Fasten pipe securely in a pipe vice (2). Be sure mark is clear so that it can be cut. Pipe must be supported on both ends to keep it from bending.
![Page 45: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/45.jpg)
Continued…• Open the jaws of the pipe cutter enough to
allow the pipe cutter to be placed around the pipe. Adjust so that the cutting blade (3) is on the line.
![Page 46: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/46.jpg)
Continued…
4. Tighten the handle (4) until cutting blade
makes contact with pipe.
5. Then turn the handle (4) 1/4 of a turn more
clockwise.
6. Now turn the whole cutter one turn around the
pipe (counter clockwise).
![Page 47: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/47.jpg)
3.2 Chipping Chipping metal (chiselling)
• You can chip the metal to produce grooves or to
reduce the width or thickness.
• Nowadays the grinder, shaper and miller are widely
used for this purpose, but if these machines are not
available, chipping is still an economical process.
![Page 48: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/48.jpg)
Procedures to chip metal1. Hold the metal in the vice.
2. Hold the chisel at an angle of about 45° to the work.
3. Hammer to remove the chip
![Page 49: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/49.jpg)
Chisels• It is used to cut cold metals and made of cast steel
or alloy steel.• The common types of chisels are
flat chisel: it used for general-purpose chiselling
cross-cut chisel: used for cutting grooves such as keyways, and for chipping;
half-round round-nosed chisel: used for cutting grooves (which are either curved or half-round).
diamond-pointed chisel: used for working into corners and cutting small grooves
![Page 50: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/50.jpg)
Continued…• Chiselling is one of the methods of
cutting material.
• Working in Chisel is inaccurate, but still widely used in mechanical workshop.
• When it becomes difficult to use shears or a saw, you can use the chisel in cutting metal plate or sheet, the process is called chopping out.
![Page 51: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/51.jpg)
![Page 52: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/52.jpg)
3.3. Filling
• Filing is a method of removing metal,
and the file which is the most widely
used hand tool in the school workshop,
is used for this cutting operation. It is
made of carbon tool steel containing
about 1.3 per cent carbon.
• Filing is a skill that is difficult to learn.
It is not easy to explain how to use a
file.
![Page 53: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/53.jpg)
principles of cross-filing
1. Hold the work firmly in the vice.
2. Allow a small part of the work to project from the vice and avoid vibration.
3. The work should normally be level with your elbow 4. Apply pressure in the forward stroke only.
5. Observe the correct methods for handling files, for
![Page 54: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/54.jpg)
![Page 55: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/55.jpg)
![Page 56: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/56.jpg)
![Page 57: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/57.jpg)
![Page 58: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/58.jpg)
3.4. Drilling, boring, counter boring,
spot-facing• Drilling in engineering refers to cutting a
circular hole in a material.
• before reaming, holes should be drilled.
• Drilling and reaming are therefore not the
same process.
• Boring, on the other hand, is making an
existing hole larger.
![Page 59: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/59.jpg)
Types of drilling machine include
![Page 60: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/60.jpg)
Continued…• hand drill is used to hold drill bits up to 5 mm for
light hand operations.
• electric hand drill is used in the same way as the
hand drill, but it is electrically powered and
controlled.
![Page 61: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/61.jpg)
![Page 62: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/62.jpg)
3.5. Lapping
• Sheet metalwork involves bending, cutting and joining of such materials as tinplate, aluminium, brass and galvanized mild steel.
• Hand shears (also known as tin man's snips) are made of tool steel
![Page 63: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/63.jpg)
Stakes
• Stakes may be referred to as small anvils, as
you use them for similar operations.
• The hatchet stake is usually used to turn
edges more than 90°.
• The brick iron is used for cylindrical and
conical work.
• The half-moon is used for turning edges of
circular or curved work.
![Page 64: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/64.jpg)
Continued…
• The funnel stake is used for forming conical and cylindrical work.
• The round-bottom stake is used for shaping the circular or curved bottoms of circular work.
• The tin man's anvil is used to true flat work.
• The creasing iron is used for preparing beaded and wired edges.
![Page 65: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/65.jpg)
![Page 66: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/66.jpg)
![Page 67: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/67.jpg)
![Page 68: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/68.jpg)
Mallets and Folding bars • Mallets are used for flattening and bending sheet
metalwork
• The heads are usually made of wood, hide or
plastic. Common types include the tin man's mallet
and the bossing mallet
• Folding bars come in lengths of 250-300 mm, and
are used for bending sheet metal at right angles.
• Groove Punch also known as a seaming tool, has
semi-circular or rectangular grooves. It is used for
fixing wired and folded seams in position.
![Page 69: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/69.jpg)
Soldering bit…• It is made of copper. The two main shapes are
hatchet and straight. The bits are used in soft soldering.
• They are heated in soldering stoves before melting the solder. There are also electric soldering bits.
• The soldering iron is heated in the tin man's stove (gas soldering stove).
• Heat the bit until the green flame shows: this is an indication that the correct temperature has been reached.
![Page 70: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/70.jpg)
Joints
• Types of Joints
![Page 71: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/71.jpg)
Bending
![Page 72: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/72.jpg)
![Page 73: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/73.jpg)
![Page 74: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/74.jpg)
Reaming• Reamers are used to enlarge and true a hole
• They are also used to remove burrs from the inside diameters of pipes and drilled holes.
(1). body the (2).shank (3). blades
![Page 75: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/75.jpg)
SOLID TAPER-PIN REAMER
![Page 76: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/76.jpg)
SOLID STRAIGHT-HOLE REAMER
![Page 77: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/77.jpg)
Expansion reamer
![Page 78: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/78.jpg)
ADJUSTABLE-BLADE REAMER
![Page 79: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/79.jpg)
Pipe reamer
![Page 80: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/80.jpg)
USING A SOLID STRAIGHT-HOLE REAMERI. Secure the work in a vice so that the hole to
be reamed is perpendicular to the top of the vice jaws.1 Secure the work in a vise so that the hole to be reamed is perpendicular to the top of the
vise jaws.
![Page 81: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/81.jpg)
ii. Using a tap wrench (1), tighten the handle to the square end of the reamer shank (2).
2 Using a tap wrench (1), tighten the handle to the square end of the reamer shank (2).
![Page 82: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/82.jpg)
iii. Position the reamer (3) at the top of the hole. Turn the wrench clockwise very slowly until the reamer is centeredin the hole. Straight-hole reamers (4) have a slight taper at
the end so they will fit into the hole easily.
iv. Turn the wrench clockwise with a steady, firm pres-
![Page 83: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/83.jpg)
Thread cutting• Screwing is a temporary method of
fastening parts together
• Methods for cutting screw threads include the use of the centre lathe.
• For bench work, however, taps and dies are used.
![Page 84: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/84.jpg)
Taps and dies• Tapes are the tools used for cutting internal
(female) threads. The term for cutting internal threads by hand is tapping
![Page 85: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/85.jpg)
Procedure for tapping
1. Drill a hole that has about the same diameter as the core of the tap.
2. Hold the work firmly in the vice.
3. Grip the first tap in the tap wrench or holder
![Page 86: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/86.jpg)
Continued…4. Insert the tap squarely in the hole and turn it clockwise to start threading
5. Turn anti-clockwise about a quarter-turn to break the sward.
6. Apply cutting oil through the flutes, to ease cutting and 'wash' away the chippings.
7. Repeat operation 5 until the entire length of thread on the tap has gone through (if it is a through hole).
![Page 87: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/87.jpg)
![Page 88: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/88.jpg)
Dies
• Dies are made either of high-carbon steel or of high speed steel. Unlike taps, dies are used for cutting external (male) threads).
![Page 89: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/89.jpg)
procedure for cutting external threads
• Square the end of the work and chamfer it (using a file, grinding machine or centre lathe) for an easy start (Figure 3.31).
![Page 90: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/90.jpg)
Continued…
• Grip the die, held in the stock, firmly and squarely on the work.
• Turn clockwise, about a quarter-turn, and ease back to remove chippings.
• Apply a good supply of oil (lubricant).
• Make adjustments of the screws after making a full cut until the depth required is achieved
![Page 91: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/91.jpg)
3.8.Grinding
• Grinders are mechanical devices which allow you to reshape, form, and sharpen metal cutting tools or other tools.
BENCH GRINDER
![Page 92: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/92.jpg)
Bench grinder…
![Page 93: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/93.jpg)
SHARPENING STONES• Sharpening stones usually have one coarse
face and one fine face.
![Page 94: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/94.jpg)
3.9. Replacing Broken tools
• Maintenance is one of the most important jobs you will do in the Navy.
• preventive maintenance is not done properly, or not done at all, your equipment may be put out of commission until it can be repaired.
• NEVER USE DAMAGED TOOLS
![Page 95: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/95.jpg)
4. Clean up
4.1 Work area
• Keep your working area, especially the floor, clean and free from any unnecessary items that can cause slipping or stumbling
• Materials should be properly stored in a material rack
• Protect the floor against spilled cutting oil.
![Page 96: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/96.jpg)
4.2 Tools and equipment• The tools and equipment's should be
cleaned after the required activities are performed.
• At last they should be stored in the recommended area based on the specifications from the industries they are manufactured to give the expected services.
![Page 97: Performing bench work ppt](https://reader031.vdocument.in/reader031/viewer/2022012320/55a6839e1a28ab37498b4751/html5/thumbnails/97.jpg)
END OF THE MODULE
2005 E.C